TENDA TECHNOLOGY HG305-GP N300 Wireless VoIP GPON Router User Manual

SHENZHEN TENDA TECHNOLOGY CO., LTD. N300 Wireless VoIP GPON Router Users Manual

Users Manual

3. Configure the RouterStep 1: Log in to the web UI of the router1. Start a web browser, enter 192.168.1.1 in the address bar, and press Enter on the keyboard.2. Enter the login username and password (admin for both by default), and click Login.Step 2: Perform the registration process1. Choose Network > Remote Management > Authentication Methods to enter the configuration page.2. Select an authentication method based on the information provided by your internet service provider (ISP), and enter the required parameters.3. Click Submit button on the bottom of the page.Step 3: Create a WAN connection1. Choose Network > WAN > WAN Connection to enter the configuration page.2. IP Version: Select your IP version. Take IPv4 as an example.3. Type: Select your connection type. Take PPPoE as an example.4. Connection Name: Select Create WAN Connection.5. Service List: Select a service type from the drop-down list. Take INTERNET as an example.6. VLAN Type: Select a VLAN type. Take Tag as an example.7. VLAN ID: Enter the VLAN ID provided by your ISP.8. 802.1p: Specify a priority for the WAN service based on the information provided by your ISP.9. Username: Enter the PPPoE user name provided by your ISP.10. Password: Enter the PPPoE password provided by your ISP.11. Click Create button on the bottom of the page.* If other parameters on this page are provided by your ISP, configure them according to your needs.Step 4: Configure the WiFi settings1. Choose Network > WLAN > SSID Settings to enter the configuration page.2. Change the WiFi name (SSID Name).3. Choose Network > WLAN > Security to enter the configuration page.4. Change the WPA Passphrase (WiFi password).5. Click Submit button on the bottom of the page.FAQQ1: I cannot access the web UI of the router after I enter 192.168.1.1 in the address bar. What should I do? A1: Try the following solutions one by one to troubleshoot the problem: Verify that the Ethernet cable is connected properly and the corresponding LED lights are in normal status. Check the IP address settings of your computer. Verify it is set to Obtain an IP address automatically. Connect your computer to another LAN port of the router. Clear the cache of your web browser. Try entering 192.168.1.1 in the address bar of another browser to log in. Try login on another computer. Hold down the Reset button for about 5 seconds to reset the router to factory default. Then enter 192.168.1.1 in the address bar of a web browser to login again.Q4: I forget the login password. What should I do?A4: Hold down the Reset button on this device for about 5 seconds to restore it to factory default. Then try login with the default user name and password (admin for both).Caution：Adapter Model: BN063-A12012EManufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO.,LTD.Input: 100-240 V AC 50/60 Hz 0.4 AOutput: 12 V DC 1 A : DC VoltageRECYCLING© 2017 Shenzhen Tenda Technology Co., Ltd. All rights reserved.Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders. Specifications are subject to change without notice.6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052Canada Hotline: 1-888-998-8966 HongKong Hotline: 00852-81931998 Skype: TendaszWebsite: http://www.tendacn.com E-mail: support@tenda.com.cnLogout HG305-GStatus Network Security Application Administration MaintenanceWANBindingLAN Address SettingPrefix ManagementWLANRemote ManagementITMSCertificateAuthentication MethodsQoSSNTPRoutingAuthentication MethodsSNLOID SNAuthentication PasswordSubmit CancelLoginUsernamePasswordadmin.....LoginCreate CancelStatus Network Security Application Administration MaintenanceWAN4in6 Tunnel SettingsARP SettingDHCP Release FirstBindingLAN Address SettingPrefix ManagementWLANRemote ManagementQoSSNTPRoutingIP Version IP v4Type PPPoEConnection Name Create WAN ConnectionPort Binding LAN1 LAN2 LAN3 LAN4SSID1 SSID2 SSID3 SSID4Enable DHCP ServerEnable NATService List INTERNETVLAN Type TagVLAN ID802.1p 0Enable DSCPDSCPMTU 1492UsernamePasswordEnable PPPoE Proxy Allow MaxUserNum 4Enable Pass ThroughAuthentication Type AutoConnection Trigger Always OnIdle Timeout 1200 secWAN ConnectionStatus Network Security Application Administration MaintenanceWANBindingLAN Address SettingPrefix ManagementWLANBasicSSID SettingsSecurityRemote ManagementQoSSNTPRoutingChoose SSID SSID1Broadcast Disable SSID EnableMaximum Clients 32 （1~32）SSID Name SSID1 （1~32 Char）Submit CancelStatus Network Security Application Administration MaintenanceWANBindingLAN Address SettingPrefix ManagementWLANBasicSSID SettingsSecurityRemote ManagementQoSSNTPRoutingChoose SSID SSID1Authentication Type WPA/WPA2-PSKWPA Passphrase !@#$%12345 (8 ~ 63 characters)WPA Encryption Algorithm TKIP+AESSubmit CancelWP S WL AN Re setUSBPlease read this installation guide before you start. You can visit our website at www.tendacn.com for more information about the router.Packing ListInstallation GuideN300 Wireless VoIP GPON RouterModel: HG305-GGPON Router * 1Power Adapter * 1Ethernet Cable * 1Phone Cable * 1Installation Guide * 11. Get to Know the RouterTop PanelLED Indicator Color Status DescriptionPOWER GreenSolid on The ONU is connected to a power supply properly.Off The ONU is not powered on, or not connected to a power supply.INET GreenSolid onBlinkingOffThe Ethernet connection is established successfully.The ONU is transmitting or receiving data.The ONU does not obtain a correct IP address, or Ethernet connection does not exist.PON GreenSolid onBlinkingOffThe ONU is succeeded in being activated.The ONU is being activated.The ONU is failed to be activated.LOS RedBlinkingOffThe receiving optical power of the ONU is lower than the sensitivity of the optical receiver.The ONU is receiving optical power properly.LAN1/2/3/4 GreenSolid onBlinkingOffThe LAN port is connected to a device properly, but no data is being transmitted.The LAN port is transmitting or receiving data.The LAN port is not connected to a device properly.TEL1/2 GreenSolid onBlinkingOffThe soft switch is succeeded in being registered by the ONU, but no traffic is being transmitted.The traffic is being transmitted.The soft switch is failed to be registered by the ONU.WLAN GreenSolid onBlinkingOffThe wireless function is enabled, and no data is being transmitted.The ONU is transmitting or receiving data in wireless manner.The wireless function is disabled.WPS GreenSolid onBlinkingOffThe WPS negotiation is successful.The ONU is performing WPS negotiation.The WPS feature is disabled, or the WPS negotiation fails.USB GreenSolid onBlinkingOffThe USB port is connected to a device properly, and works in Host manner. But no data is being transmitted.The USB port is transmitting or receiving data.The USB port is not connected to a device.Rear PanelButton/Port DescriptionON/OFFPOWERLAN1/2/3/4PONTEL1/2Power button. Used to turn on/off the ONU.Power jack. Used to connect to a power receptacle using the included power adapter for power supply.LAN ports. Used to connect to a computer, set-top box, router, switch, and so on.SC/APC optical fiber port. Used to connect to the internet.POTS ports. Used to connect to a telephone or fax machine.Side PanelTEL2 TEL1 PON LAN4 LAN3 LAN2 L AN1 POWER ON/OFFButton/Port DescriptionWPSWLANResetUSBWPS button. Press it to perform WPS negotiation.WiFi button. Press it to enable/disable WiFi.Reset button. Hold it down for 5 seconds to restore the factory settings of the router. Restoring the router to factory settings clears all settings of the router. You need to configure the router again for internet access.USB port. Used to connect to a USB flash disk for resources sharing.Environment RequirementsOperating temperature: 0 °C~40 °C Operating humidity: 10%~90% RH non-condensingAnti-static PrecautionElectrostatic adsorption occurs if dust falls onto the router, which may disable the router to work properly. To prevent this problem, keep the air in the ambient environment clean and regularly perform dedusting. 2. Connect the RouterStep 1: Connect the PON port to the internet using an indoor fiber cord.Step 2: Connect a computer to one of the LAN ports of the router.Step 3: Connect the router to a power receptacle using the included power adapter.Step 4: Turn on the router.Q2: The router (ONU) cannot be registered. What should I do?A2: Try the following solutions one by one to troubleshoot the problem: Verify that the fiber cord is connected to the router properly. Check the status of the LOS LED indicator. If it stays blinking, check whether the optical module input power is within its normal range of -8~-28 dBm which is displayed on the Status > Network Information > GPON Information page of the web UI. If not, verify that the fiber terminal is clean, and the fiber is not bent excessively. Check the status of the PON LED indicator. If it is off, check whether you select correct authentication method, and the authentication information you entered is correct. If the problem persists, contact your ISP.Q3: The registration is successful but I cannot access the internet. What should I do?A3: Try the following solutions one by one to troubleshoot the problem: Check whether the GPON router obtains valid IP address, DNS, and gateway information which is displayed on the Status > Network Information > IPv4/IPv6 Connection page of the web UI. If not, verify that the WAN connection you create is correct and valid. Verify that the IP address of your computer is set to “Obtain an IP address automatically”. If your problem still persists, contact your ISP.TipsLED Indicator Color Status Description1. Get to Know the RouterCE Mark WarningThis is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.Declaration of ConformityHereby, SHENZHEN TENDA TECHNOLOGY CO. LTD. declares that the radio equipment type HG305-G is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: http://www.tendacn.com/en/service/page/ce.htmlOperate Frequency: 2.4GHz-2.4835GHzEIRP Power (Max.): 18dBmSoftware Version: V1.0.0.0This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.POWER L AN2INET PO N LOS LAN 1 LAN3 LA N4 TE L1 T EL2 W LAN WPS U SBPOWER LAN2INET PON LOS LAN1 LAN3 LAN4 TEL1 TEL2 WLAN WPS USB Caution, laserNOTEDO NOT look directly at the PON port when the router is powered on, neither the terminal ofthe indoor fiber cord, to prevent any harm to your eyes.---End.FCC StatementThis device is restricted to be used in the indoor. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:— Reorient or relocate the receiving antenna.— Increase the separation between the equipment and receiver.— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.— Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.SHENZHEN TENDA TECHNOLOGY CO.,LTD

Navigation menu