TENDA TECHNOLOGY TEL9901G 10/100/1000 MBPS NETWORK INTERFACE CARD User Manual

SHENZHEN TENDA TECHNOLOGY CO., LTD. 10/100/1000 MBPS NETWORK INTERFACE CARD Users Manual

Users Manual

 Copyright Statement  is  the  registered  trademark  of Shenzhen  Tenda  Technology  Co.,  Ltd.  Other trademark or trade name mentioned herein are the trademark or registered trademark of the company. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co., Ltd, individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages. All  the  photos  and  product  specifications mentioned in this manual are for references only, as the upgrading of software and hardware, there will be changes. And if there are changes, Tenda is not responsible for informing in advance. If you  want  to  know  more  about  our  products information,  please  visit  our  website  at www.tenda.cn
  1   Table of Contents   1 Product Description..................................... 1 1.1 Unpacking ............................................1 1.2 Main Features ....................................1 1.3 Specifications .................................. 3 1.4  LED Indicators ................................ 3 2 Hardware Installation............................ 5 3 Driver Installation ....................................... 6
  11 Product Description  Thanks  for  purchasing TENDA  TEL9901G  10/100/ 1000M auto-Negotiation Gigabit PCI LAN Adapter. TEL9901G is fully compliant with PCI2.2, support ACPI  power  management.  TEL9901G  is  Auto- Negotiation,  supports  three  transfer  rate  of 10Mbps, 100Mbps and 1000Mbps. Being able to auto detect  the  transfer  rate  of  the  networking devices connected and also support full and half duplex modes. Besides, TEL9901G also supports Boot ROM and RPL/PXE. TENDA TEL9901G supports driver software under the operation system of Windows 98, Windows ME, Windows 2000, Windows NT, Windows XP, Windows NT, Linux and Novell etc.   1.1 Unpacking  This package contains: 10/100/1000Mbps Gigabit PCI LAN Adapter 1CD Driver   1User’s Manual   1Quality-passed Certificate Card  1Quality Warranty Card  1  1.2 Main Features  TEL9901G  is  fully  compliant  with  IEEE802.3 10Base-T , IEEE802.3u  100Base-Tx , IEEE802.3ab 1000Base-T protocol, supports IEEE802.3x full  duplex flow control, IEEE802.1p priority tag. And  also  supports  Auto-Negotiation,  auto MDI/MDI-X, simple to configure and economic. It
  2is  your  best  choice  for  realizing  Gigabit Network to your desktop. Compliant  with  IEEE802.3,  IEEE802.3u, IEEE802.3ab standard; Supports  transfer  rate  of  10Mbps,  100Mbps, 1000Mbps and duplex of 10/100M under full duplex mode, half duplex, 1000M under full duplex mode. Supports  NWAY  Auto-Negotiation,  auto  detect transfer rate, duplex mode, and able to select an optimal network connecting mode and  avoid complex configuration, Plug-and-Play Supports auto MDI/MDI-X Supports IEE802.3x Flow Control for full-duplex mode Compliant  with  PCI  2.1,  PCI2.2  protocol, supports 32 bits, 33/66MHz PCI BUS, extremely low CPU consumption  Supports ACPI power management, enables you to manage power through modern operating systems and obtains optimal power management. Compliant  with  IEEE802.1Q  standard,  supports Tag VLAN, supports IEEE802.1p priority tag. Supports  the  transmitting  and  receiving  of Gigabit Jumbo Frame Up to 2000Mbps throughput Integrated  big  capacity  independent transferring/ receiving  FIFO buffering area. Adopting high integration and high performance single chipset solution. Supports Boot ROM, able to realize RPL/PXE while inserting the appointed Boot ROM. Abundant  driving  software  supported,  almost supports  all  the  normal  operating  systems including  WIN NT4.0, WIN98SE, WIN ME, WIN 2000, WIN  XP,  NOVELL  SERVER/CLIENT,
  3LINUX2.2X/2.4X/2.6X,  MAC OS and Free BSD etc.   1.3 Specifications  Main Features Protocol IEEE802.1p   IEEE802.1Q IEEE802.3    IEEE802.3u IEEE802.3ab  IEEE802.3x  BUS Type  32bit 33/66MHZ  PCI BUS Network Interface  RJ45 I/O Address  System auto assign Disconnected (IRO) System auto assign Half/Full Duplex  Transfer Rate 10/20Mbps  100/200Mbps 2000Mbps Operating Temperature  0℃~45℃ (32  F ~112 F)Operating Humidity 10%-90% (non condensing)Consumption 5 Voltage power input from the PCI slot of the main-board, MAX 4 watts consumption   1.4  LED Indicators  One “FDX”LED ON indicates that TEL9901G is working under full duplex modeOne “1000”LED Indicates status of 1000Mbps Link/Act One “100” LED Indicates status of 100Mbps Link/Act
  4One “10” LED Indicates status of 10Mbps Link/Act Note: When the Link/Act LED is ON, it indicates that TEL9901G is connected to the network successfully at the respective transfer rate. When the Link/Act LED is blinking, it indicates that TEL9901G is transmitting data.
  5 2 Hardware Installation  Please  install  TEL9901G  according  to  the following steps: ¾ Shut down your computer, unplug its power cord and remove the chassis cover. ¾ Insert the contact edge of the DGE-530T card into the connector of any available PCI Bus Master  expansion  slot.  Press  the  card firmly  into  the  connector  such  that  the card’s  contacts  are  fully  seated  in  the connector. ¾ Install the bracket screw that secures the card to the computer chassis and replace the computer’s chassis cover. ¾ Connect TEL9901G to the network through Cat. 5 or Cat. 5 enhanced twisted pair cable. ‘
  6 3 Driver Installation  Please install the driver according to the following steps:  ¾ Start PC, and insert the CD attached in the packing. The computer would run the CD automatically and display Tenda Setup on the screen. (If the computer is not running the CD automatically, please double click the CD and run “TendaSetup.exe” ), please click the icon of “driver software” to install the driving software. ¾ Please click “TEL9901G”, select “the language of driver software” and then click “Enter” to start installation. ¾ Please select the directory for installation and click “Next” ¾ Please click “Finish” and you now install the driver successfully.
  7FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference  to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
  8To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of FCC RF Rules. Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Caution!  The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

Navigation menu