TIT ENG NL200 CARD LAMINATOR User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3530257
Application ID	r3DztVFpL3PL5khP44oIHw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	331.82kB (4147735 bits)
Date Submitted	2017-08-28 00:00:00
Date Available	2018-02-24 00:00:00
Creation Date	2017-06-27 16:29:50
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-08-25 17:07:50
Document Title	Users Manual
Document Creator	Adobe InDesign CC 2015 (Macintosh)

Load Lower Cleaning Roller & Films
- Load Lower Cleaning Roller
1. Pull the cartridge out while pressing the Cartridge Load/Eject Button to
remove it from the laminator as shown in the image below.
2. Align the Cleaning Roller with its hole and push it up until it clicks.
Cleaning roller hole
Important
- Make sure that it is fully inserted into the Cleaning Roller Hole before pushing the indicated area.
After installation
of cleaning roller
24
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
25
- Load Films to Lower Cartridge
2. Check the position of the Lower Film Cartridge and films for
rewinding and push the cartridge in until it clicks.
1. Load the films for lamination and rewinding in the correct position as
shown in the image below.
Important
RFID Tag
- Place the white film core on the core guide.
- The white film core does not fit the black
film core guide.
- Do not force the film core in as it can
damage the cartridge.
- Check the position of the RFID tag.
RFID Tag Reader
26
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
27
Load Cards
- Load Cards after taking out the Card Input Hopper
1.Hold the side of the card input hopper and pull it backward to remove it .
- Place cards in the Input Hopper
1. Open the Card input hopper by pulling it sideway.
2. Hold the backside of the card input hopper with one hand and open the
cover with the other. Then, place the cards inside as shown in the picture.
2. Place the cards inside the card input hopper as shown in the picture.
28
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
29
3. Close the cover and place the card input hopper in the tray.
Load/Unload Card Stacker to Laminator
- Load Card Stacker to Laminator
Insert the hook on the Card Stacker and push it down in the side
of the laminator. (Max. 150 cards can be loaded at once.)
Note
- The hinge is located where the card is loaded into the path to
prevent displacement.
- The hinge is lifted when the card is loaded into the laminator.
Before the card is loaded
30
©2017 T.I.TENG Co., Ltd. All rights reserved
When the card is loading
POINTMAN LAMINATOR NL200 User Manual
31
- Remove Cards after Taking Out
Card Stacker
Hold the side of Card Stacker and pull it up to remove as shown in
the image.
32
©2017 T.I.TENG Co., Ltd. All rights reserved
- Remove Cards without Taking Out Card Stacker
Use your thumb and index finger to take out 60 or fewer cards
from the Card Stacker without removing it from the laminator.
POINTMAN LAMINATOR NL200 User Manual
33
Connect Power & Communication Cables
- Connect Power Cable
Power On
Press the Power Switch (‘―’) to turn the laminator on.
Make sure that the Power Switch is off and connect the AC Power Cable to
the Power Port on the back of the laminator.
Prohibition
- The product must be used with AC power
with rated label.
- Check whether the Power Cable is
plugged in before use.
- Connect Communication Cable
To download the firmware, connect the laminator to a PC using either
RS232C or USB Port.
Power ON -> OFF
Power OFF -> ON
Electrical Hazard / Fire Hazard
If the product is exposed to rain or liquid, please turn off and unplug the cable, and contact an authorized
service representative.
USB Port
34
RS232C Port
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
35
Card Input Hopper Lock
OPTION
Front Cover Lock
OPTION
Turn the key clockwise to lock the Front Cover.
The key cannot be pulled out if the Front Cover is not closed. Do not force it
out as it can damage the Front Cover.
Insert the left side of card input
hopper lock and mount the other
side pulling to the sideway. Then,
use the Lock Key to lock it .
Locked -> Unlocked
36
©2017 T.I.TENG Co., Ltd. All rights reserved
Unlocked -> Locked
POINTMAN LAMINATOR NL200 User Manual
37
Button Control & Menu
- Pass Mode
Function : Set pass mode
- Buttons
1. Press ‘MENU’ to enter the menu mode.
2. Press ‘OK’ when ‘1. Pass mode’ appears on the LCD display.
Name
38
Description
Menu Navigation (Up)
Increase the value or navigate the menu.
Menu Navigation (Down)
Decrease the value or navigate the menu.
OK
Set the value.
Menu
Enter or exit the menu.
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
39
Note
- In the Pass mode, you can choose ‘Auto’, ‘Alone_uppper’,
‘Alone_lower’, ‘Both’ or ‘Bypass’.
Use the menu navigation buttons to navigate the menu.
3. After selecting the pass mode, press ‘OK’ to go back to the previous step.
Auto mode
Select this option to start
laminating automatically when
the card is inserted.
4. Press ‘MENU’ to go into the standby mode.
Alone_uppper
Select this option to laminate
only the upper side.
Caution
- In the Alone Upper Mode, an error occurs
if any film is loaded at the lower cartridge
Alone_lower
Select this option to laminate
only the lower side.
Caution
5. If any changes have been made, you will be prompted to save the changes.
Press ‘OK’ to save the new settings or ‘MENU’ if you do not want to save them.
- In the Alone Upper Mode, an error occurs
if any film is loaded at the lower cartridge
Both
Select this option to laminate
both upper and upper sides.
Bypass
Select this option to pass
without laminating either
upper or lower side.
40
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
41
- Lamination Temperature (Temper_set)
4. Press ‘OK’ to set the temperature and go back to the previous step.
Function: Set the temperature of the lamination heater.
You can set the temperature between 120℃ and 190℃(248℉ and 374℉)
+/- increments of 5℃(9℉)
1. Press ‘MENU’ to enter the menu mode.
5. Press ‘MENU’ to go into the standby mode.
2. Press the menu navigation button to select ‘2. Temper_set’ and press ‘OK’.
6. If any changes have been made, you will be prompted to save the changes.
Press ‘OK’ to save the new settings or ‘MENU’ if you do not want to save them.
3. Use the menu navigation button to adjust the temperature for the
lamination heater.
(It can be set between 120℃ and 190℃(248℉ and 374℉) +/- increments of
5℃(9℉).)
42
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
43
- Film Position (Start POS set)
4. Press ‘OK’ to set the position and go back to the previous step.
Function : Set the position of film and card for lamination.
- It can be set between -1.0mm ~+1.5mm +/- increments of 0.1mm.
From the direction of inserting the card, it moves back by ‘– (L)‘ value and forward by ‘+(R)’.
1. Press ‘MENU’ to enter the menu mode.
5. Press ‘MENU’ to go into the standby mode.
2. Press the Menu Navigation Button to select ‘3. Start POS set’ and press ‘OK’.
6. If any changes have been made, you will be prompted to save the changes.
Press ‘OK’ to save the new settings or ‘MENU’ if you do not want to save them.
3. Use the Menu Navigation Button to adjust the position to laminate.
(It can be set between -1.0mm ~+1.5mm +/- increments of 0.1mm.)
44
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
45
- Power Saving Mode
4. Press ‘OK’ to set the power saving mode and go back to the previous step.
Function : The system turns off if it is inactive for a set duration of time.
It can be set between 5 and 60 minutes +/- increments of 5 minutes.
1. Press ‘MENU’ to enter the menu mode.
5. Press ‘MENU’ to go into the standby mode.
2. Press the Menu Navigation Button to select ‘4. Power saving’ and press ‘OK’.
6. If any changes have been made, you will be prompted to save the changes.
Press ‘OK’ to save the new settings or ‘MENU’ if you do not want to save them.
3. Use the Menu Navigation Button to set the power saving mode.
(It can be set between 5 and 60 minutes +/- increments of 5 minutes.)
46
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
47
- Path Sensor
4. Press ‘OK’ while holding the card and it goes in.
Function : Check whether the path sensor works correctly.
1. Press ‘MENU’ to enter the menu mode.
5. The card will move back and forth 5-6 times. Each time the card passes
the sensor, the indicator changes from X to O.
2. Press the Menu Navigation Button to select ‘5. Path sensor’ and press ‘OK’.
6. The laminator releases the card upon completion.
3. Insert a card that is not printed into the Card Slot.
(Make sure to hold the card until the operation starts.)
48
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
49
7. Press 'OK' to go back to the previous step.
- Serial No. (Product_infor)
Function : check the serial number of the product.
1. Press ‘MENU’ to enter the menu mode.
8. Press ‘MENU’ to go into the standby mode.
2. Press the menu navigation button to select ‘7. Product_infor’ and press ‘OK’.
3. Check the serial number.
The first 4 digits indicate the year and month of manufacture and the last
4 digits mean production lot number.
50
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
51
6. Press 'MENU' to go back to the previous step.
- Factory Reset (Factory init)
Function : Reset the system to factory default settings.
Default Settings: Pass mode : Auto, Temper_set: 150℃(302℉),
Start_POS set : 0mm, Power_saving: 5min
1. Press ‘MENU’ to enter the menu mode.
7. Press ‘MENU’ to go into the standby mode.
2. Press the Menu Navigation Button to select ‘8. Factory init’ and press ‘OK’.
3. Press ‘OK’ and ‘Setting init?’ appears on the screen.
52
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
53
4. Press ‘OK’ to proceed or ‘MENU’ to cancel the action. (You will be directed
to the previous step when you press either ‘OK’ or ‘MENU’.)
6. If any changes have been made, you will be prompted to save the changes.
Press ‘OK’ to save the new settings or ‘MENU’ if you do not want to save them.
5. Press ‘MENU’ to go into the standby mode.
54
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
55
Maintenance Instructions
- Supported Cards
The following cards are recommended for the prevention of jams
and the best results.
① Size
- International Standard (CR-79, CR-80 ISO 7810)
- 53.98mm (W) x 85.60mm (L)/3.375"x2.215"
Clean the Laminator
- Clean the Exterior
- Make sure to turn off the laminator and unplug the power cable
before cleaning it with a soft cloth slightly dampened with water.
- Do not allow any liquid to drip inside the printer.
- Make sure that the printer is dry before turning it on.
Caution
Do not use any liquid / gel containing a high content of alcohol or solvent to
clean the printer as it may cause discoloration or fissure on its surface.
② Thickness
- Standard : 0.76mm~1.0mm (30mil~40mil)
③ Acceptable Cards
- Glossy white
- Free of dirt or grease
- Not contaminated
- Free of scratches or dents
- Completely flat
- Static Free
- Clean Roller Using Cleaning Card
It is recommended to clean the laminator using the cleaning card every month
or each time 500 cards are laminated in order to maintain quality and prevent
damage to the important parts.
1. Press ‘MENU’ to enter the menu mode.
④ Unacceptable Cards
- Heavily damaged
- Stained or contaminated
- Scratched
- Bent or deformed
- Embossed
2. Press the menu navigation button to select ‘6. Path cleaning’ and press ‘OK’.
Caution
Do not use cards considered unacceptable
as they may damage the parts.
56
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
57
3. Insert the cleaning card to the card ejector.
(Make sure to hold the card until the operation starts.)
6. The card will be released once the cleaning process is complete.
7. Press 'MENU' to go back to the previous step.
4. Press ‘OK’ while holding the card and it goes in.
8. Press ‘MENU’ to go into the standby mode.
5. The card will move back and forth 3-4 times while cleaning the roller.
58
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
59
- Clean the Blue Cleaning Roller
Troubleshooting
Some of the problems you may encounter while using the printer can be
fixed by referring to the following troubleshooting guide.
If the problem persists, then please contact your local dealer.
- Error Messages & Solutions
Error
Messages
Blue Cleaning Roller
This cleaning tool is designed to remove any unwanted materials from
the surface of cards, and it can be used semi-permanently since it can be
washed.
It is recommended to clean it at least once every two weeks. If more than
400 cards are laminated within a month, it is recommended to clean it every
200 times of use.
1. Remove the cleaning roller from the laminator
60
©2017 T.I.TENG Co., Ltd. All rights reserved
Solution
해결
E11
The temperature of the heater not in
use is too high.
Leave the laminator for a while to cool it
off. (Power off)
E13
The card loader is empty.
If the error message persists when the
cards are loaded, please contact the
service representative for assistance.
E20
The Front Cover is open
Check whether the cover is closed. If the
problem persists, please contact the service
representative for assistance.
E21
No cartridge is loaded.
Check the cartridge. If the problem persists,
please contact the service representative
for assistance.
E22
There is no film. The tag cannot be
recognized.
Check if there are films. If there are
enough films, check whether the tag can
be recognized. If not, please contact the
service representative for assistance.
E24
The Pass Mode does not match how
the cartridge ribbon is loaded.
(ex. Pass Mode is set to Both in the
menu settings and only the lower
cartridge has films.)
Check if there are films. If there are
enough films, check whether the tag can
be recognized. If not, please contact the
service representative for assistance.
E25
The sensor does not recognize the
ribbon mark while lamination is in
process.
Check the ribbon mark on the film. If
there is no problem with the ribbon mark,
please contact the service representative
for assistance.
E26
Jam occurs when there is no
lamination process.
If there is no card inside the laminator or
slot, the system goes back to normal. If the
problem persists, please contact the service
representative for assistance.
E42
The heater module fails to return to
its original position.
Restart the system 2-3 times. If the
problem persists, please contact the service
representative for assistance.
(This is caused by overheating. Please
contact the service representative promptly
to avoid injuries.)
W10
There are 40 or fewer ribbon films.
Replace the films.
2. Wash it under running water.
3. Make sure that it is fully dried before installing it into the laminator.
Description
POINTMAN LAMINATOR NL200 User Manual
61
- Remove Jammed Card
Error
Messages
E31
Film Specifications
Description
Solution
Jam occurs while laminating.
Turn the power off and release the card
(using the handle on the back).
If the problem persists after changing the settings,
please contact the service representative for assistance.
1. Turn the power off.
- Patch-Type Film
Type
Specifications
Clear (1.0mil)
500 Prints/Roll
Hologram(1.0 mil)
500 Prints/Roll
2. Rotate the knob and remove the jammed card as shown in the image.
MEN
OK
62
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
63
Laminator Specifications
- Features
Quick heating process and laminating performance
- After initialization, the system is ready within 40 seconds and laminates both
sides within 20 seconds.
Easy operation and configuration
- Easy to operate and configure the quality settings
- Easy to load the film cartridge thanks to door-type front cover
- Designed with a knob for removing jammed card
- Wide display and convenient button control (4Line MONO LCD, 4 Control Buttons)
High level of security
- The front cover can be locked to protect the films inside (optional feature).
Large amount of laminator films
- Up to 500 laminator films (Dual sides) are supported.
⑥ Film Patch Dimensions
- Size: 81mm x 51mm (CR-79, CR-80)
- Thickness : 1.0 mil
⑦ Film Patch Capacity
- 500 patches / roll (1.0mil)
- Optional Specifications
- Card Stacker: 150 cards (0.76mm)
- Front Cover Lock (for the protection of films)
- Cradle (for connecting to a card/retransfer printer)
- Laminator Specifications
① Product Dimensions(Width x Length x Height) and Weight
1) NL200 (Standard)
- Dimensions : 216.5mm(W) x 320mm(L) x 313.5mm(H)
- Weight : 9.45kg
2) NL200 (Standard, Card Stacker)
- Standard Specifications
① Laminating Type
- Heat Roller +Halogen Lamp Type
- Dimensions : 216.5mm(W) x 443.4mm(L) x 313.5mm(H)
- Weight : 9.65kg
3) NL200H (Standard, Card Input Hopper)
② Laminating Function
- Dimensions : 216.5mm(W) x 377.2mm(L) x 313.5mm(H)
- Weight : 10kg
- Edge to edge, Dual/single sided lamination
4) NL200H (Standard, Card Input Hopper, Card Stacker)
③ Laminating Speed
- Dimensions : 216.5mm(W) x 500.6mm(L) x 313.5mm(H)
- Weight : 10.2kg
- 8mm/s (for both Dual and single sided lamination)
④ Laminating Temperature
② Power Supply
- 120℃ to 195℃(248℉ to 383℉)
- AC 110V ~ 240V
- Single 600W / Dual 600W
⑤ Supported Card Size
- CR-79, CR-80
③ Interface
- USB 2.0
- RS-232
64
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
65
Warranty Certificate
Product
Name of Customer
Model No.
Address
Manufacture
No.
Date of Purchase
Size
Warranty Period
Regulatory
-FCC
(YYYY/MM/DD)
(30 months) from the date of purchase
Purchase
Dealer
FCC IDENTIFIER : XTNNL200
Name of Grantee : TIT ENG Co.,Ltd.
Equipment Class : Part 15 Low Power Communication Device Transmitter
Notes :
Address: TEL)
- Repaired at cost if any of the following apply.
- The warranty has expired.
- The product is damaged by the negligence or misuse of the consumer
(e.g. impact, water, fire).
- The product is damaged by a natural disaster (e.g. earthquake, flood).
- The product is damaged from unauthorized repair or modification.
- Consumable parts are consumed (according to the company policy).
- The product is damaged by the use of unsupported cards.
FCC Statement
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user`s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device should be installed and operated with minimum 20 cm
between the radiator and your body.
- EU
This product is CE marked according to the provision of the R&TTE Directive (99/5/EC).
Here by T.I.T ENG Co., Ltd. Declares that this product is in compliance with the essential
requirement and other relevant provisions of Directive 1999/5/EC.
66
©2017 T.I.TENG Co., Ltd. All rights reserved
POINTMAN LAMINATOR NL200 User Manual
67
-RoHS
We hereby guarantee that all products that POINTMAN will deliver directly or
through any third party to you, do not contain Pb, Cd, Hg, CR+6, PBB, PBDE
to the beat of our knowledge, Thereby our products are in accordance with
RoHS2 Directive.
- Directive 2002/95/EC
- Directive 2005/717/EC
- Directive 2005/747/EC
68
©2017 T.I.TENG Co., Ltd. All rights reserved
This document is the copyright of T.I.T ENG Co., Ltd. and may not be reproduced in
full or in part by any means, electronic or otherwise, without the prior written consent
of T.I.T ENG Co., Ltd.
The Company would be very grateful if any accidental inaccuracies could be pointed
out to us, as well as any other constructive criticism which might lead to a better
understanding.
T.I.T ENG Co.,Ltd.
7th floor, Shin-do B/D, 215, Jungdae-ro, Songpa-gu, Seoul, Korea (ZIP: 05702)
sales@pointman.co.kr
POINTMAN Technologies Inc.
260 Maple Court Suite 277, Ventura, CA 93003,
TEL: +1 844 384 3279, www.pointmanusa.com
POINTMAN Trading Co.,Ltd
Room 10G, Building B, Zhongyangdadao, Baoyuan Road 2004,
Xixiang Street, Bao an district, Shenzhen, China (ZIP: 518102)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2017:06:27 16:29:50+09:00
Creator                         : Adobe InDesign CC 2015 (Macintosh)
Modify Date                     : 2017:08:25 17:07:50+09:00
Language                        : ko-KP
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Metadata Date                   : 2017:08:25 17:07:50+09:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Instance ID                     : uuid:0d67ebc9-6d95-47b4-a610-5308e58da746
Original Document ID            : xmp.did:a8bbca65-383f-4601-bff0-eed9724059a1
Document ID                     : xmp.id:683cbe35-2027-4b8b-95e5-e8d6156bdc10
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:82ceb991-840b-440f-b001-53507649f016
Derived From Document ID        : xmp.did:8a4e08fa-a075-4959-89e5-0d7181d8377f
Derived From Original Document ID: xmp.did:a8bbca65-383f-4601-bff0-eed9724059a1
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2017:06:27 16:29:50+09:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 24

EXIF Metadata provided by EXIF.tools