TP Link Technologies CPE210 2.4 GHz 300Mpbs 9dBi Outdoor CPE User Manual CPE210 updated PART2

TP-Link Technologies Co., Ltd. 2.4 GHz 300Mpbs 9dBi Outdoor CPE CPE210 updated PART2

Contents

CPE210_User Manual_updated-PART2

122. Open your web browser, type 'http://192.168.0.254' in the address  eld and press 'Enter'. It is recommended to use the latest version of Google Chrome, Safari or Firefox.3. The 'Login' page will appear, set the parameters as below. • Username: admin • Password: admin • Region: select according to your country/region • Select 'I agree to these terms of use' • Click 'Login'4. At the  rst login, change the 'Password' for safety.For subsequent logins, you only need to enter the username and password that you have set to log in.
135. Then you will log in to the PharOS Web Interface and see the Status page, shown as the  gure below.
14• Point-to-PointPoint-to-Point application is used to build a transparent bridge between two locations which are far from each other. The gure shown below is an example for this application.Refer to the following steps to congure the CPEs.2. Conguration for Typical ApplicationThis section introduces the congurations for the Point-to-Point application. Congure the Access Point1. Log in to PharOS2. Go to the Quick Setup page3. Operation Mode • Select 'Access Point' • Click 'Next'4. LAN Settings: Click 'Next'5. Wireless AP Settings • SSID: customize the name for the network as you like • Security: select 'WPA-PSK/WPA2-PSK' • PSK Password: create the password for the network as you like • Distance Setting: enter the distance between the Access Point and the Client. It is recommended to round the number up to the nearest integer • Select the MAXtream option if the Access Point and the Client both are Pharos outdoor CPEs. (Refer to Q4 in FAQ for details about MAXtream) • Click 'Next'6. Finsh: Click 'Finish'IP cameraAccess PointLAN: 192.168.0.254ClientLAN: 192.168.0.2Computer
15Congure the Client1. Log in to PharOS2. Go to the Quick Setup page3. Operation Mode • Select 'Client' • Click 'Next'4. LAN Settings • IP Address: 192.168.0.2 (on the same subnet with the Access Point) • Click 'Next'5. Wireless Client Settings • SSID of Remote AP: click 'Survey', select the SSID of the Access Point, and click 'Connect' • Security: select 'WPA-PSK/WPA2-PSK' • PSK Password: enter the password of the Access Point • Distance Setting: enter the same number with the Access Point • Click 'Next'6. Finsh: Click 'Finish'
16Antenna AlignmentIn order to get the best performance, you can precisely align the direction of the CPE with the assistance of 'Wireless Signal Quality' on STATUS page of the Pharos Web Interface.24dB22dB18dB22dB18dBWISPAdjust the direction of the CPE until the device reaches the highest SNR
17 HARDWARE FEATURES Dimensions CPE520/CPE220: 275.83*79*60.3mm CPE510/CPE210: 224.34*79*60.3mm Interface LAN0: 10/100Mbps Ethernet Port(PoE IN) LAN1: 10/100Mbps Ethernet Port GND: Grounding Terminal for Lightning Protection RESET: Button to restore the device to Factory Default Power Supply 24V Passive PoE Adapter Included ESD Protection1) 15kV Lightning Protection1) 6kV Operating Temperature -30℃~60℃ (-22℉~158℉) Operating Humidity 5% ~ 95 % Certication CE, FCC, RoHS, IPX5 WIRELESS FEATURES Models CPE210 CPE220 CPE510 CPE520 Antenna Gain 9dBi 12dBi 13dBi 16dBiHorizontal Beamwidth/Elevation Beamwidth2) 65°/ 45° 45°/ 30° 45°/ 33° 50°/ 20°Maximum Transmit Power3) 27dBm 30dBma 27dBm 30dBmOperating Frequency 2.4- 2.4835GHz 2.4- 2.4835GHz 5.15- 5.85GHz 5.15- 5.85GHz802.11 Standards 11b/g/n 11b/g/n 11a/n 11a/nSpecications1) Estimation is based on copper grounding cable and shielded CAT5e cable with ESD drain wire.2) Beamwidth values may vary throughout operating frequency.3) Maximum transmit power and operating frequency may vary in dierent countries or regions.Note
18Frequently Asked Questions (FAQ)Q1. How to restore the CPE to its factory default settings?With the CPE powered on, press and hold the 'RESET' button of the CPE or the 'Remote Reset' button of the Passive PoE Adapter for about 8 seconds until the Wireless Signal Strength LEDs ash.RESETRemoteResetPharos CPE:Passive PoE Adapter:
19Q2. How to calculate the minimum mounting height of the devices?In order to maximize the received signal strength of the devices, installers need to minimize the eect of the out-of-phase signals, which is caused by obstacles in the path between the transmitter and the receiver. Fresnel Zone is a usual method to calculate this path, as shown in the formula and the gure below.where,r = Fresnel zone radius in metersc = 3x108 m/s, speed of lightf = operating frequency of the devices in Hzd1 & d2 = the distances between the point and the devices in metersh = the height of obstacle at this pointH h+r*(1 40%)(H is the height of the CPE)For example, assume d1 is 2km, d2 is 8km, and f is 2.4GHz, then r would be 14.142m. Considering a toleration of 40%, allowable radius would be 8.485m. Assume h is 10m, then the result of the minimum mounting height based on this point would be 18.485m. Similarly, calculate the results based on all the points where there are obstacles, and the maximum value would be the nal result.For more information, please refer to http://en.wikipedia.org/wiki/Fresnel_zone fcddddr⋅+×=2121d2rd1
20Q3. How can I use Spectrum Analysis to  nd the appropriate channel for the devices?1. Log in to PharOS, on the 'WIRELESS' page, you can  nd the 'Spectrum Analysis' button as shown in the  gure below. Click the button.2. The following window will pop up. Click 'Yes' and you will then get into the Spectrum Analysis page. 3. Select the 'Frequency Range' and click the 'Start' button, the PharOS will begin to analyze the power of the frequency. Watch the curves for a period of time, and then click 'Stop'. Mark the relatively low and continuous part of the average curve, and note the corresponding frequency range. Here we take the  gure below as an example.into the Spectrum Analysis page. into the Spectrum Analysis page. into the Spectrum Analysis page.
214. Close the Spectrum Analysis Window, and then you will get back to the Wireless page. For the Channel/Frequency option, it is recommended to select a value whose frequency is within the noted frequency range. So, in this example, the recommended Channel/Frequency is 116/5580MHz.Q4. What is Pharos MAXtream?Pharos MAXtream is a proprietary protocol developed on the basis of Time Division Multiple Access (TDMA) by TP-LINK.The MAXtream technology has the following advantages:• Eliminates hidden node collisions & improves channel effi ciency.• Lower latency, higher throughput, larger network capacity & more stability.To enable the MAXtream function among the AP and stations, you only need to select the MAXtream option on the 'WIRELESS' page of the PharOS Web Interface of the AP, shown as the  gure below. Then the stations will automatically adjust their connections to the AP.Pharos MAXtream is a non-standard Wi-Fi protocol that is only compatible with TP-LINK’s Pharos series products. Please notice that you will not be able to connect other Wi-Fi devices to an AP with MAXtream enabled.
FCC STATEMENTCE Mark WarningThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user’s authority to operate the equipment.This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.FCC RF Radiation Exposure Statement:This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Congurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”Limited to local law of the United States, selecting country code and channel function was disabled.The permitted channel&power is controlled by wireless driver.The end-user have no permission and no way to change it. That is to say that The device can only work in legal channel&power.
Canadian Compliance StatementThis product can be used in the following countries:AT / BG / BY / CA / CZ / DE / DK / EE / ES / FI / FR / GB / GR / HU / IE / IT LT / LV / MT / NL / NO / PL / PT / RO / RU / SE / SK / TR / UA This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device.Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d’interférences et (2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.Industry Canada StatementComplies with the Canadian ICES-003 Class B specications.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.Safety Information• When product has power button, the power button is one of the way to shut o the product; When there is no power button, the only way to completely shut o power is to disconnect the product or the power adapter from the power source.• Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.• Avoid water and wet locations.
COPYRIGHT & TRADEMARKSSpecications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.No part of the specications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.Website: http://www.tp-link.comTel: +86 755 26504400 E-mail: support@tp-link.com7106504648 REV1.0.0

Navigation menu