TP Link Technologies CPE610V1 5GHz 300Mbps 23dBi Outdoor CPE User Manual Part 1

TP-Link Technologies Co., Ltd. 5GHz 300Mbps 23dBi Outdoor CPE Part 1

Contents

User Manual Part 1

CPE610Outdoor CPEInstallation Guide
ContentsOverviewPackage ContentsHardware OverviewHardware ConnectionSite ConsiderationHardware InstallationPower SupplyLightning & ESD ProtectionSoftware ConfigurationLogging in to the PharOSConfiguration for a Typical ApplicationAntenna AlignmentSpecificationsFAQ1415181920
TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless network solutions. This guide is applicable to the product CPE610. OverviewPackage Contents1Power Cord Passive PoE AdapterInstallation GuideCPE610Installation GuideOutdoor CPEPharos CPE Center Reflector Panel Side Reflector Panels(Qty.2)Bolts with Nut and LockWasher Assemblies(M6×110, Qty.2)Bolts with Nut and LockWasher Assemblies(M6×70)Rear Cover Mounting Bracket(For CPE)Pole-mount ClampST3×10 Self-tapping Screws(Qty.2)D3×28 Plastic Wall Anchors(Qty.2)Mounting Bracket(For PoE Adapter)Protective Cap
Bottom ViewHardware Overview2Reflector AssemblySecuring ArmsBubble LevelMounting BracketPole-mount ClampRear Cover
3On: A device is connected to this port, but there is no activity.Flashing: A device is connected to this port, and is active.On: The CPE is powered on.Panel LayoutOn: The wireless function is enabled.Passive PoE Adapter Power LEDOn: Power on.Off: Power off.Remote ResetPress and hold for 5 seconds to reset the CPE to its factory defaults.RESETPress and hold for 5 seconds to reset the CPE to its factory defaults.ETHERNETThe port is to connect to the POE port of the provided PoE adapter for both data transmission and power supply through Ethernet cabling.
4Hardware ConnectionSite ConsiderationEnsure a clear line of sight between the wireless devices for optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. See 'Q2' in 'FAQ' for details about how to calculate the minimum mounting height of the devices.Mounting HeightLine of SightSide View
5OrientationInstall the CPE devices so that they point towards the devices that will receive the signal. You can orient the devices with the help of Google Maps, GPS and some landmarks. The horizontal bandwidth of CPE610 is 6.8°.AshenzhenBLine of SightHorizontal Beamwidth
61. Attach the Side Reflector Panels to the Center Reflector Panel as follows:a. Insert the two mounting studs on the Center Reflector Panel into the large opening of the slots on the Side Reflector Panel.b. Slide the Side Reflector Panel until the mounting studs are positioned over the narrow opening of the slots, and the top edges of the panels should be aligned when done.Hardware Installation
7c. Repeat step a and step b to attach the other Side Reflector Panel.d. (Optional) Attach the Side Reflector Panels to the Center Reflector Panel more securely using four M2.5x8 bolts and nuts (not provided). This is recommended if the CPE device is exposed to extreme weather, such as strong winds.2. Attach the Rear Cover to the reflector assembly as follows:a. While holding the reflector assembly, align the raised edges on the back with the Securing Arms of the Rear Cover, and align the Snap Hooks on the Rear Cover with the slots on the Center Reflector Panel.
8b. Attach the Rear Cover to the reflector assembly. Press upon the Rear Cover at the four positions marked in the diagram below in sequence until it locks into place. WARNING: To avoid damage, do not place the panels on a flat surface or push down on it.1243

Navigation menu