TP Link Technologies CPE610V2 5GHz 300Mbps 23dBi Outdoor CPE User Manual 5 User Manual rev1

TP-Link Technologies Co., Ltd. 5GHz 300Mbps 23dBi Outdoor CPE 5 User Manual rev1

5. User Manual rev1

CPE6105GHz 300Mbps 23dBi Outdoor CPEInstallation Guide
ContentsOverviewPackage ContentsHardware OverviewHardware ConnectionSite ConsiderationApplication ExampleHardware InstallationPower SupplyLightning & ESD ProtectionInstaller Compliance ResponsibilitySoftware ConfigurationLogging in to the PharOSConfiguration for a Typical ApplicationAntenna AlignmentSpecificationsFAQ1420212217
TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless network solutions. This guide is applicable to the product CPE610. OverviewPackage Contents1Power Cord Passive PoE AdapterInstallation GuideCPE610Installation GuideOutdoor CPEPharos CPE Center Reflector Panel Side Reflector Panels(Qty.2)Bolts with Nut and LockWasher Assemblies(M6×110, Qty.2)Bolts with Nut and LockWasher Assemblies(M6×70)Rear Cover Mounting Bracket(For CPE)Pole-mount ClampST3×16 Self-tapping Screws(Qty.2)D3×28 Plastic Wall Anchors(Qty.2)Mounting Bracket(For PoE Adapter)Protective Cap
Bottom ViewHardware Overview2Reflector AssemblySecuring ArmsBubble LevelMounting BracketPole-mount ClampRear Cover
3On: A device is connected to the ETHERNET port, but there is no activity.Flashing: A device is connected to the ETHERNET port and is active.On: The CPE is powered on.Panel LayoutOn: The wireless function is enabled.Passive PoE Adapter Power LEDOn: Power on.Off: Power off.Remote ResetPress and hold for 5 seconds to reset the CPE to its factory defaults.RESETPress and hold for 5 seconds to reset the CPE to its factory defaults.ETHERNETThe port is used to connect to the POE port of the provided PoE adapter for both data transmission and power supply through Ethernet cabling.Attention:The Adapter which works at 0-40 shall be installed and placed in an indoor environment.
4Hardware ConnectionSite ConsiderationEnsure a clear line of sight between the wireless devices for optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. See 'Q2' in 'FAQ' for details about how to calculate the minimum mounting height of the devices.Mounting HeightLine of SightSide View
5OrientationInstall the CPE devices so that they point towards the devices that will receive the signal. You can orient the devices with the help of Google Maps, GPS and some landmarks. The horizontal bandwidth of CPE610 is 7°.AshenzhenBLine of SightHorizontal Beamwidth
Application ExampleThe CPE device with the reflector installed provides outdoor network access over long distances for point-to-point applications.The CPE device without the reflector installed provides outdoor -to-indoor Wi-Fi coverage with the Feed only mode.6
71. Attach the Side Reflector Panels to the Center Reflector Panel as follows:a. Insert the two mounting studs on the Center Reflector Panel into the large opening of the slots on the Side Reflector Panel.b. Slide the Side Reflector Panel until the mounting studs are positioned over the narrow opening of the slots, and the top edges of the panels should be aligned when done.Hardware InstallationTERMS OF USE: Installers must abide by local rules and regulations in terms of legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements.
8c. Repeat step a and step b to attach the other Side Reflector Panel.d. (Optional) Attach the Side Reflector Panels to the Center Reflector Panel more securely using four M2.5x8 bolts and nuts (not provided). This is recommended if the CPE device is exposed to extreme weather, such as strong winds.2. Attach the Rear Cover to the reflector assembly as follows:a. While holding the reflector assembly, align the raised edges on the back with the Securing Arms of the Rear Cover, and align the Snap Hooks on the Rear Cover with the slots on the Center Reflector Panel.
9b. Attach the Rear Cover to the reflector assembly. Press upon the Rear Cover at the four positions marked in the diagram below in sequence until it locks into place. WARNING: To avoid damage, do not place the panels on a flat surface or push down on it.1243
103. Insert the Pharos CPE into the Rear Cover until the CPE locks into place.4. Connect the Ethernet cable to the Pharos CPE.a. Connect the Ethernet cable to the Ethernet port.Note: The length of the Ethernet cable is up to 60m for steady power supply.
11b. Attach the Protective Cap to the Rear Cover.5. Attach the Mounting Bracket to the Rear Cover until the grooves on the Mounting Bracket are positioned over the pins on the Rear Cover.
126. Secure the Mounting Bracket to the Rear Cover using M6x70 Bolts with Nut and Lock Washer Assemblies.7. Attach the CPE assembly to the pole using two Pole-mount Clamps and two M6x110 Bolts with Nut and Lock Washer Assemblies.a. Insert the two Bolts into the Mounting Bracket.
13b. Secure the Pole-mount Clamps with Nuts and Washers.Note: Suitable pole diameters range from 15mm to 70mm.8. Adjust the azimuth and elevation angle of the CPE device to achieve maximum signal strength.
14Power SupplyConnecting the PoE AdapterConnect the devices as shown in the figure below.PoE LANEthernet cable length up to 60mMounting the PoE Adapter (Optional)Note: To ensure the passive PoE adapter is attached most securely, it is recommended to install the adapter with the Ethernet port facing upward.1. Drill two holes on the wall and insert the plastic wall anchors into the the holes. Secure the mounting bracket to the wall.2. Attach the passive PoE adapter to the mounting bracket by sliding the adapter in the direction of the arrows until it locks into place.
15Lightning & ESD ProtectionProper grounding is extremely important for outdoor devices.By using shielded CAT5e (or above) cable with ground wire and the provided PoE adapter, you can effectively eliminate ESD attacks.CPEPoE Adapter with Earth GroundShielded CAT5e (or above)Cable with Ground WireGrounded 3-wirePower OutletTwisted PairGround WireSecondary Cable ShieldCable ShieldSheath
Installer Compliance ResponsibilityDevices must be professionally installed and it is theprofessional installer's responsibility to make sure the device isoperated within local rules and regulations.Since TP-Link’s Pharos outdoor CPE610 can be paired with avariety of antennas, the Antenna and TransmitPower fields are provided to the professional installer to assistin meeting regulatory requirements.Refer to Antenna and Transmit Power elds to make sure the devices are operated within local rules and regulations.16
17Open a web browser, type http://192.168.0.254 into the address field and press Enter (Windows) or return (Mac). It is recommended to use the latest version of Google Chrome, Firefox or Safari.Software CongurationLogging in to the PharOSBefore accessing the PharOS Web Interface, you need to assign a static IP address 192.168.0.X (X ranges between 2 and 253, e.g. 192.168.0.10) to your computer.This chapter introduces the login to the PharOS Web Interface and the software configurations.1.2.192.168.0.254Enter admin for both User Name and Password, then select the Language from the drop-down list. Read and agree to the terms of use, then click Login.3.
18Change the default User Name and Password for security purposes. You can then start to configure your CPE.1. Log in to PharOS and go to the Quick Setup page.2. Operation Mode: Select Access Point and click Next.3. LAN Settings: Click Next.4. Wireless AP Settings: a. Create a new SSID (Network name) for your wireless network.b. Select WPA-PSK/WPA2-PSK for the Security method and create a PSK Password to protect your AP. Congure the Access Point (AP)For subsequent logins, use the new username and password.Conguration for a Typical ApplicationThe typical topology is as follows: Multiple wireless bridges are built among the access point and the clients. Follow the instructions below to configure the Access Point and the Client.For simplicity, we will take one wireless bridge as an example.4.For more configurations, please visit https://www.tp-link.com/support to download the User Guide of PharOS products in the download center.Access PointClientClientClient
19Congure the Client1. Log in to PharOS and go to the Quick Setup page.2. Operation Mode: Select Client and click Next.3. LAN Settings: Change the IP Address to 192.168.0.X (X ranges between 2 and 253), the same subnet as the access point, and click Next.4. Wireless Client Settings: a. Click Survey and select the SSID of the Access Point in the AP list, then click Connect.b. Select WPA-PSK/WPA2-PSK from the Security option, enter the same PSK password and distance value of the Access Point, then click Next.5. Finish: Verify your settings and click Finish to complete the configuration.For more configurations, please visit https://www.tp-link.com/support to download the User Guide of PharOS products in the download center.c. Enter the distance between the Access Point and the Client into the Distance Setting field.d. Select the MAXtream checkbox (Refer to Q3 in FAQ for details about MAXtream), and click Next.5. Finish: Verify your settings and click Finish to complete the configuration.
20Antenna AlignmentIn order to get the best performance, you can precisely align the direction of the CPE with the assistance of Wireless Signal Quality on the STATUS page of the PharOS Web Interface.Adjust the direction of the CPE until the SNR reaches a maximum.WBS+AntennaWBS+Antenna
21SpecicationsInterfacePower Supply11ESD Protection Lightning Protection Operating HumidityOperating TemperatureCertication10/100Mbps Ethernet port24V passive PoE adapter included 15KVUp to 6KV-40 to 70 (-40 to 158 )℉℉ 10% to 90%CE, FCC, RoHS, IP65℃℃Note:1. Estimation is based on shielded CAT5e(or above) cable with an integrated grounding wire.HARDWARE FEATURESWIRELESS FEATURES802.11 Standards 11a/nButton RESET: Restore the device to its factory defaults
22FAQ How to restore the CPE to its factory default settings?With the CPE powered on, press and hold the RESET button on the CPE for about 5 seconds.Q1.Method 1:Method 2:RESET Button:Press & hold for about 5 secondsRemote Reset Button:Press & hold for about 5 secondsWith the CPE powered on, press and hold the Remote Reset button on the passive PoE adapter for about 5 seconds.
23How to calculate the minimum mounting heightof the devices?In order to maximize the received signal strength of the devices, you need to minimize the effect of the out-of-phase signals, which is caused by obstacles in the path between the transmitter and the receiver. Fresnel Zone is a usual method to calculate this path, as shown in the formula and the figure below.Q2.h = the height ofobstacle at this point H h+r*(1 40%)(H is the height of the CPE)d2rd1where,r = Fresnel zone radius in metersc = 3x108 m/s, speed of lightf = operating frequency of the devices in Hzd1 & d2 = the distances between the point and the devices in metersFor example, assume d1 is 2km, d2 is 8km, and f is 2.4GHz, then r would be 14.142m. Considering a toleration of 40%, allowable radius would be 8.485m. Assume h is 10m, then the result of the minimum mounting height based on this point would be 18.485m. Similarly, calculate the results based on all the points where there are obstacles, and the maximum value would be the final result.For more information, please refer to:http://en.wikipedia.org/wiki/Fresnel_zonefcddddr⋅+×=2121
24What is Pharos MAXtream?Pharos MAXtream is a proprietary protocol developed on the basis of Time Division Multiple Access (TDMA) by TP-Link.The MAXtream technology has the following advantages:Eliminates hidden node collisions & improves channel efficiency.Lower latency, higher throughput, larger network capacity & more stability.Improves the QoS for video, voice and sound data stream.By dividing the timing of transmission into different time slots, MAXtream allows the Pharos devices to transmit in rapid succession, one after another, each stream using its own time slot to transmit and receive frames, which greatly reduces the chance of collision.Pharos MAXtream is a non-standard Wi-Fi protocol that is only compatible with TP-Link’s Pharos series products. Please note that you will not be able to connect other Wi-Fi devices to an AP with MAXtream enabled.Q3.Log in to PharOS, click Spectrum Analysis in the tools drop-down list, a window will pop up to remind you that all wireless connections will be lost during spectrum analysis. Click Yes to continue to the Spectrum Analysis page.1. How can I use Spectrum Analysis to find the appropriate channel for the devices?Q4.
252.Click Start, PharOS will begin to analyze the power of frequency. Observe the curves for a period of time, and then click Stop. Note that the relatively low and continuous part of the average curve indicates less radio noise. Here, we use the figure below as an example. 3. When choosing channel/frequency, you should avoid the spectrum with large radio noise. In this example, the recommended channel/ frequency is 112/5560MHz.
FCC STATEMENTFCC RF Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2018/ 06/ 14
CE Mark WarningThis is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. RF Exposure InformationEU declaration of conformityTP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU.The original EU declaration of conformity may be found at http://ww-w.tp-link.com/en/ceRF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body.OPERATING FREQUENCY(the maxi-mum transmitted power)5470 MHz -5725 MHz (30dBm)
Safety InformationKeep the device away from water, fire, humidity or hot environments.Do not attempt to disassemble, repair, or modify the device.Do not use damaged charger or USB cable to charge the device.Do not use any other chargers than those recommended.Do not use the device where wireless devices are not allowed.Adapter shall be installed near the equipment and shall be easily accessible.Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us.For EU/EFTA, this product can be used in the following countries:AT / BE / BG / CH / CY / CZ / DE / DK / EE / EL / EF / FI / FR / HR / HU / IE / IS / IT / LI / LT / LU / LV / MT / NL / NO / PL / PT / RO / SE / SI / SK / UK• • • •• • DC voltage Symbol ExplanationRECYCLINGThis product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.Explanation of the symbols on the product labelПродукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
© 2018 TP-Link 7106508090 REV1.0.2The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public License (“GPL”). As applicable, the terms of the GPL and any information on obtaining access to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under (https://www.tp-link.com/en/support/g-pl/). The respective programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more authors. For details, see the GPL Code and other terms of the GPL.For technical support, User Guide and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.

Navigation menu