TP Link Technologies LBM100 Light Bulb Wi-Fi Module User Manual EUT RF test specification

TP-Link Technologies Co., Ltd. Light Bulb Wi-Fi Module EUT RF test specification

TE7LMB100_User Manual Rev.2

LBM100 User ManualFCC STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the followingmeasures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.Consult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions:1）This device may not cause harmful interference.2）This device must accept any interference received, including interferencethat may cause undesired operation.Any changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.Note: The manufacturer is not responsible for any radio or TV interference caused byunauthorized modifications to this equipment. Such modifications could void the user’sauthority to operate the equipment.FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for anuncontrolled environment. This device and its antenna must not be co-located oroperating in conjunction with any other antenna or transmitter.“To comply with FCC RF exposure compliance requirements, this grant is applicable toonly Mobile Configurations. The antennas used for this transmitter must be installed toprovide a separation distance of at least 20 cm from all persons and must not beco-located or operating in conjunction with any other antenna or transmitter.”This device is restricted in indoor environment only.Canadian Compliance StatementThis device complies with Industry Canada license-exempt RSSs. Operation is subject tothe following two conditions:1）This device may not cause interference, and2）This device must accept any interference, including interference that maycause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareilsradio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :3）l’appareil ne doit pas produire de brouillage;4）l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,meme si le brouillage est susceptible d’en compromettre le fonctionnement.This radio transmitter (IC: 8853A-LBM100/ Model: LBM100) has been approved byIndustry Canada to operate with the antenna types listed below with the maximumpermissible gain indicated. Antenna types not included in this list (Appendix A), having again greater than the maximum gain indicated for that type, are strictly prohibited for usewith this device.Le présent émetteur radio (IC: 8853A-LBM100/ Model: LBM100) a été approuvé parIndustrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous etayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste(Annexe A), et dont le gain est supérieur au gain maximal indiqué, sont strictementinterdits pour l'exploitation de l'émetteur.Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with minimum distance20cm between the radiator & your body.Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pourun environnement non contrôlé. Cet équipement doit être installé et utilisé avec unminimum de 20 cm de distance entre la source de rayonnement et votre corps.Industry Canada StatementCAN ICES-3 (B)/NMB-3(B)
1. OverviewThe LBM100 Wi-Fi module provides a highly-integraed and flexible platform fordeveloping and evaluating products and applications based on the QCA4010SoC.The LBM100 Wi-Fi module can be either used with development kit for softwaredevelopment or incorporated into OEM products to enable rapid deployment of Wi-Ficonnected systems.The module includes the following components:QCA4010 chipAn integrated BalunA printed antenna2MB SPI FlashShield2. Interface and pinoutInterface:Debug UARTI2C slavePWM x4USB2.0 for ART toolPinout:
3. Electric FeaturePower SupplyTypeDCInput3.3V0.3ATypical700WStandby Mode324mW4. Mechanic FeatureSize: 36.50mm*16.00mm*3.9mm5. Wireless FeatureOperating Frequency:2.4GHz:2412~2462MHzTransfer Rate: 802.11b: 11/5.5/2/1 Mbps802.11g: 54/48/36/24/18/9/6 Mbps802.11n: up to 150 MbpsWireless Channel: ch1-ch11(ch1-ch9 for 11nHT40)Transimit Power:18dBm(max)Antenna Type: An printed Omni Directional antenna with 2.37dBi gain6. Physical and EnvironmentalOperating Temperature: 0℃～100℃Storage Temperature: -1 0℃～100℃Working Humidity: 10%～90% RH7. Additional DescriptionThe module will be installed inside another device. And the outside of the device intowhich the module is installed will display a label referring to the enclosed module.This exterior label will use the wording such as “Contains FCC ID: TE7LBM100Contains IC: 8853A-LBM100”, or any other similar wording that expresses the samemeaning.

Navigation menu