TP Link Technologies LBM100 Light Bulb Wi-Fi Module User Manual EUT RF test specification

Download:
Mirror Download [FCC.gov]
Document ID	2950518
Application ID	jV4UIIZ+VtxyyboC6Q2bWQ==
Document Description	TE7LMB100_User Manual Rev.2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.21kB (152659 bits)
Date Submitted	2016-04-05 00:00:00
Date Available	2016-04-06 00:00:00
Creation Date	2016-03-28 15:48:58
Document Lastmod	2016-03-28 15:48:58
Document Title	EUT RF test specification
Document Author:	qiuchenshuo

LBM100 User Manual
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:


Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1）
2）
This device may not cause harmful interference.
This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to
only Mobile Configurations. The antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.”
This device is restricted in indoor environment only.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is subject to
the following two conditions:
1）
2）
This device may not cause interference, and
This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
3）
4）
l’appareil ne doit pas produire de brouillage;
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
meme si le brouillage est susceptible d’en compromettre le fonctionnement.
This radio transmitter (IC: 8853A-LBM100/ Model: LBM100) has been approved by
Industry Canada to operate with the antenna types listed below with the maximum
permissible gain indicated. Antenna types not included in this list (Appendix A), having a
gain greater than the maximum gain indicated for that type, are strictly prohibited for use
with this device.
Le présent émetteur radio (IC: 8853A-LBM100/ Model: LBM100) a été approuvé par
Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et
ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste
(Annexe A), et dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
1. Overview
The LBM100 Wi-Fi module provides a highly-integraed and flexible platform for
developing and evaluating products and applications based on the QCA4010
SoC.The LBM100 Wi-Fi module can be either used with development kit for software
development or incorporated into OEM products to enable rapid deployment of Wi-Fi
connected systems.
The module includes the following components:
QCA4010 chip
An integrated Balun
A printed antenna
2MB SPI Flash
Shield
2. Interface and pinout
Interface:
Debug UART
I2C slave
PWM x4
USB2.0 for ART tool
Pinout:
3. Electric Feature
Power Supply
Type
DC
Input
3.3V0.3A
Typical
700W
Standby Mode
324mW
4. Mechanic Feature
Size: 36.50mm*16.00mm*3.9mm
5. Wireless Feature
Operating Frequency:2.4GHz:2412~2462MHz
Transfer Rate:
802.11b: 11/5.5/2/1 Mbps
802.11g: 54/48/36/24/18/9/6 Mbps
802.11n: up to 150 Mbps
Wireless Channel: ch1-ch11(ch1-ch9 for 11nHT40)
Transimit Power:18dBm(max)
Antenna Type: An printed Omni Directional antenna with 2.37dBi gain
6. Physical and Environmental
Operating Temperature: 0℃～100℃
Storage Temperature:
-1 0℃～100℃
Working Humidity:
10%～90% RH
7. Additional Description
The module will be installed inside another device. And the outside of the device into
which the module is installed will display a label referring to the enclosed module.
This exterior label will use the wording such as “Contains FCC ID: TE7LBM100
Contains IC: 8853A-LBM100”, or any other similar wording that expresses the same
meaning.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 5
Create Date                     : 2016:03:28 15:48:58+00:00
Modify Date                     : 2016:03:28 15:48:58+00:00
Title                           : EUT RF test specification
Author                          : qiuchenshuo
Creator                         : WPS Office 专业版

EXIF Metadata provided by EXIF.tools