TP Link Technologies M5350V1 3G Mobile Wi-Fi User Manual User Man TE7M5350V1 rev 3
TP-Link Technologies Co., Ltd. 3G Mobile Wi-Fi User Man TE7M5350V1 rev 3
User Man_TE7M5350V1_rev 3
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2149698 |
| Application ID | TYDxd5cYG1PO+GfpcblbsQ== |
| Document Description | User Man_TE7M5350V1_rev 3 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 186.48kB (2330961 bits) |
| Date Submitted | 2013-12-23 00:00:00 |
| Date Available | 2013-12-23 00:00:00 |
| Creation Date | 2013-01-28 09:17:16 |
| Producing Software | Adobe PDF Library 10.0 |
| Document Lastmod | 2013-12-23 15:07:48 |
| Document Title | User Man_TE7M5350V1_rev 3 |
| Document Creator | Adobe Illustrator CS3 |
M5350 3G Mobile Wi-Fi REV 1.0.0 1910010751 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. In SAR test, 1cm form the body is the distance to test the human exposure to radio frequency fields. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device has been designed to operate with an internal antenna, please do not change an antenna. This product has been tested for SAR item to insure the human exposure to radio frequency fields under a safe level. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1)cet appareil ne doit pas provoquer d’interférences et (2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou quele dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. NCC Notice & BSMI Notice 注意！ 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，費經許可，公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立 即停用，并改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率 射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 安全諮詢及注意事項 ● 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ● 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ● 注意防潮，請勿將水或其他液體潑灑到本產品上。 ● 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ● 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ● 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information When product has power button, the power button is one of the way to shut off the product; When there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE ES FI FR GB GR HU IE IT LT LV MT NL NO PL PT RO RU SE SK TR UA TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 3G Mobile Wi-Fi Model No.: M5350 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.1.1:2009 ETSI EN 301489-7 V1.3.1：2005& ETSI EN301489-24 V1.5.1：2010 EN 301908-1 V5.2.1：2011& EN 301908-2 V5.2.1：2011 EN301511 V9.0.2：2003 EN 55022:2010+AC:2011 EN 55024:2010 EN 61000-3-3:2008 EN 61000-3-2:2006+A1:2009+A2:2009 EN 60950-1:2006+A11：2009+A1:2010+A12:2011 EN 62311:2008 EN62209-2:2010 The product carries the CE Mark: Person responsible for marking this declaration: Yang Hongliang Product Manager of International Business Date of issue: 2013 TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China CONTENTS Package Contents ....................................................................................................... 1 Chapter 1. Introduction ......................................................................................... 2 1.1 Product Overview ......................................................................................................... 2 1.2 Main Features .............................................................................................................. 2 1.3 Physical Description ..................................................................................................... 2 Chapter 2. Hardware Installation.......................................................................... 4 2.1 Environment Requirements .......................................................................................... 4 2.2 Hardware Installation.................................................................................................... 4 Chapter 3. Quick Installation Guide ..................................................................... 7 3.1 System Requirements .................................................................................................. 7 3.2 TCP/IP Configuration ................................................................................................... 7 3.3 Wireless Connection .................................................................................................... 7 3.4 Quick Setup .................................................................................................................. 8 Chapter 4. Device Configuration ........................................................................ 12 4.1 Connection ................................................................................................................. 12 4.2 Quick Setup ................................................................................................................ 13 4.3 SMS ........................................................................................................................... 13 4.4 4.3.1 New Message ................................................................................................. 13 4.3.2 Inbox ............................................................................................................... 14 4.3.3 Sentbox .......................................................................................................... 14 4.3.4 Drafts .............................................................................................................. 15 4.3.5 Settings........................................................................................................... 16 Advanced ................................................................................................................... 17 4.4.1 Dial-up ............................................................................................................ 17 4.4.2 Wi-Fi ............................................................................................................... 23 4.4.3 DHCP ............................................................................................................. 26 4.4.4 Tools ............................................................................................................... 28 Appendix A: FAQ....................................................................................................... 32 Appendix B: Configuring the PC ............................................................................. 33 Appendix C: Specifications...................................................................................... 36 Appendix D: Glossary .............................................................................................. 37 M5350 3G Mobile Wi-Fi User Guide Package Contents The following items should be found in your package: M5350 3G Mobile Wi-Fi One power adapter One USB cable One battery Quick Installation Guide Note: Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact with your distributor. Conventions The Device or M5350 mentioned in this guide stands for M5350 3G Mobile Wi-Fi without any explanation. Attention: All the 3G function described below is not available in the United States. 3G function is designed for other countries except the United States. -1- M5350 Chapter 1. 3G Mobile Wi-Fi User Guide Introduction 1.1 Product Overview TP-LINK’s M5350 is at the forefront of wireless 3G sharing. Equipped with a built-in 3G modem, you can instantly establish your own Wi-Fi hotspot simply by inserting a 3G SIM card at the interior of the device. With up to 21.6Mbps download and 5.76Mbps upload speeds, M5350 is able to provide 3G wireless sharing to up to 10 users simultaneously. Its pocket-sized design and powerful 2000mAh internal battery make it an ideal travel companion, allowing users to work or play for hours on end. Besides, with its innovative OLED display, users can have a much more intuitive view of the device’s working status, such as signal strength, network type (2G/3G), Wi-Fi status, message, internet status and battery meter. 1.2 Main Features Equipped with a built-in 3G modem - No other bulky devices required HSPA+ supported with up to 21.6Mbps download and 5.76Mbps upload speeds Supports up to 10 users simultaneously 2000mAh internal battery for extended hours of outdoor use Portable and cobblestone design ideal for travel use Micro USB port for versatile recharging OLED display provides an intuitive view of the device’s working status Equipped with a micro SD card slot for up to 32GB of optional storage 1.3 Physical Description Power Button OLED Screen Micro USB Port Figure 1-1 the Exterior SIM Card Slot Micro SD Memory Card Slot RESET Button (hole) Figure 1-2 the Interior -2- M5350 3G Mobile Wi-Fi User Guide The details about the Exterior and Interior are explained as below. Power Button: When the Device is successfully installed, and it’s powered (either by battery or electricity); press this button for about 5 seconds to turn on the Device, and if you want to turn it off, please press this button for another 3 seconds. Micro USB Port: It’s for you to connect the Device with the power adapter (attached in the package) via the USB cable. SIM Card Slot: It’s where to insert your SIM card. Micro SD Memory Card Slot: It’s where to insert your micro SD memory card. RESET Button (hole): It’s the button to restore the Device to its factory defaults. With the Device powered on, use a pin to press and hold the RESET button (hole) for about 5 seconds, until the LED screen is off and later displays “TP-LINK”; then release the button and wait the Device to reboot and restore its factory default settings. OLED Screen: Figure 1-3 LED Screen The OLED Indication: Item Description Indication Signal Strength Indicates the signal strength of current 2G/3G network. Network Option Displays the current network option: 2G or 3G. Wi-Fi Connection Displays the amount of un-read short message(s); if the icon flashes, it means the mail-box is full. SMS Connection Status Battery Status Connection Mode 52B/125B Displays the Wi-Fi status and the amount of current wireless client. Traffic Statistics Indicates the successful network connection. Displays the remaining battery power. Means the automatic mode of Internet connection; Means the manual mode of Internet connection. Means “current traffic/ total traffic”. (The “current traffic” will be cleared every time the device turns off, while the “total traffic” will be cleared only when the device is reset.) Table 1-1 The OLED Screen details Note: When you leave alone the buttons on the device, the OLED screen will light on for 55 seconds and then turn off. Later when you press the power button, the OLED screen will light up and display the related information. -3- M5350 Chapter 2. 3G Mobile Wi-Fi User Guide Hardware Installation 2.1 Environment Requirements Place the Device in a well-ventilated place far from any heater or heating vent Avoid direct irradiation of any strong light (such as sunlight) Keep at least 2 inches (5 cm) of clear space around the Device Operating Temperature: 0℃~40℃ (32℉~104℉) Operating Humidity: 10%~90%RH, Non-condensing 2.2 Hardware Installation STEP 1: Install SIM card and memory card. 1) Open the cover upwards (as the arrow shows). 2) Make sure to have the SIM card’s metal chip downwards and the triangle notch outwards, and then slide the card into its slot (in the direction as the arrow shows). Note: If you have a Micro-SIM or Nano-SIM, please use an adapter to convert it to a standard SIM card. 3) First, push and then lift the locker to open it. Second, have the memory card’s metal chip downwards and inwards, and then fit it in its slot. Finally, put down and then pull the locker to lock it. -4- M5350 3G Mobile Wi-Fi User Guide Note: The micro SD memory card is optional. You can purchase it appropriate to your own need. STEP 2: Install the battery. 1) Touch the metal contacts of the battery to the metal points of the Device, and then press to fit the battery body into the slot. 2) Before closing the cover, please note down the SSID and the wireless password on the label for later use. SSID: The wireless network name of M5350 Wireless Password: The pre-encryption of M5350 3) Close the cover by pressing it. -5- M5350 3G Mobile Wi-Fi User Guide Note: It’s advised that you do not use M5350 until the battery has been installed. When finishing the above two-step installation, you can press the power button 5 seconds to turn on M5350. Tips: You are supported to charge the battery in two ways: Method 1: 1) Connect one end of the USB cable to the micro USB port. 2) Connect the other end of the USB cable to the USB port of the power adapter. 3) Plug the power adapter to a standard wall socket. Method 2: 1) Connect one end of the USB cable to the micro USB port. 2) Connect the other end of the USB cable to the USB port of your PC. -6- for about M5350 Chapter 3. 3G Mobile Wi-Fi User Guide Quick Installation Guide This chapter will guide you to quickly set up the basic functions for your M5350 3G Mobile Wi-Fi. 3.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Device is connected directly to the Ethernet.) PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors TCP/IP protocol on each PC Web browser, such as Microsoft Internet Explorer 5.0 , Netscape Navigator 6.0 or above 3.2 TCP/IP Configuration The default IP address of the M5350 3G Mobile Wi-Fi is 192.168.0.1, and the default Subnet Mask is 255.255.255.0, which values can be changed as you desire. In this guide, we use all the default values for description, and take the configuration in Windows 7 for example. While, Pads or Wi-Fi cellphones by default obtain IP address and DNS server address automatically, so you can just skip this step and continue with the 3.3 Wireless Connection. Note: Before configuration, please make sure your computer has been equipped with a wireless network adapter. Obtain an IP address automatically 1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. Please refer to Appendix B: Configuring the PC for the detailed instructions. 2) Then the built-in DHCP server will assign an IP address for the PC. Configure the IP address manually 1) Set up the TCP/IP Protocol for your PC. Please refer to Appendix B: Configuring the PC for the detailed instructions. 2) Configure the network parameters. The IP address is 192.168.0.X ( X stands for any number from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.0.1 (the device's default IP address). 3.3 Wireless Connection Note: To log in the Device’s web-based management page, you need to first connect to the wireless network of the Device. at the bottom of your desktop. 1. Click the icon 2. Click the refresh button , and then select the SSID of M5350 and then click Connect. -7- M5350 3G Mobile Wi-Fi User Guide Note: The default SSID (also called Wireless Network Name) of the device is TP-LINK_M5_XXXXXX (XXXXXX is the last 6 characters of the device’s MAC address. 3. Enter the wireless password you’ve noted down in the Security Key field, and then click OK. Note: You can refer to the label on the rear cover for the default SSID and wireless password of M5350. 4. When Connected appears behind the SSID of M5350, you’ve successfully connected to its wireless network. Note: After successful connection to M5350 (with a SIM card inserted), you can enjoy the 3G mobile connection instantaneously. Otherwise, please continue with 3.4 Quick Setup to further configure your device. 3.4 Quick Setup 1. Open a web-browser, enter the default address 192.168.0.1 in the address field and then press Enter. When the login window appears, enter admin (in lower case letters) for both User Name and Password, and then click the OK button or press the Enter. -8- M5350 Figure 3-1 3G Mobile Wi-Fi User Guide Login Windows Note: If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go to Tools menu > Internet Options > Connections > LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2. After successful login, there will appear the Quick Setup page. Click Next to continue. Figure 3-2 3. Quick Setup – Start On the Dial-up Settings page shows the related information of the SIM card inserted. Click Next to continue, if you are sure the information is correct. You can also click New to create a new profile. -9- M5350 Figure 3-3 4. 3G Mobile Wi-Fi User Guide Quick Setup – Dial-up Settings On the Wi-Fi Settings page, you can create a unique and easy-to-remember wireless network name (SSID) or keep it default, and in the Wireless Password field set a wireless password for your network. Then click Next to continue. Figure 3-4 5. Quick Setup – Wi-Fi Settings On the Finish page, please double-check your settings. If all the parameters are verified, click Finish to complete the Quick Setup; if there is anything wrong, you can click Back to re-configure it. -10- M5350 Figure 3-5 Quick Setup – Finish -11- 3G Mobile Wi-Fi User Guide M5350 Chapter 4. 3G Mobile Wi-Fi User Guide Device Configuration After the successful login to the web-based management page of M5350, you will see the main menu listing Connection, Quick Setup, SMS, and Advanced on the top. In the following parts, these items will be explained in details, about their respective functions and configurations. Figure 4-1 Main Menu 4.1 Connection The Status page displays the current status information about the device. All information is read-only. Figure 4-2 Connection Connection Status: Displays the device’s current connection status, including the connection and SIM status, network type, received and sent traffics and their totals, duration and its total, etc. WAN Status: Displays the device’s current WAN status, including IP address, DNS server and connection mode. Wi-Fi Status: Displays the device’s current wireless settings, including SSID, channel, security mode and current Wi-Fi clients. Click Wi-Fi Settings to head for the Wi-Fi Settings page and configure it. Click Clear to clear the total traffic statistics and total duration of the device Click Refresh to get the status information updated. -12- M5350 3G Mobile Wi-Fi User Guide 4.2 Quick Setup Please refer to 3.4 Quick Setup. 4.3 SMS Figure 4-3 SMS Menu There are five submenus under the SMS tab (as shown in Figure 4-3): New Message, Inbox, Sentbox, Drafts and Settings. Click any of them, and you will be able to configure the corresponding functions. 4.3.1 New Message Figure 4-4 New Message Number: Enter the receiver’s cellphone number. Contents: Text your message in this box. Click Send to send the message. Click Save to save the message in the Drafts box. -13- M5350 3G Mobile Wi-Fi User Guide 4.3.2 Inbox Figure 4-5 Inbox Index: The index of the message. Status: means the message has been read. means the message hasn't been read yet. Date: Shows the date when the message was received. Number: Shows the cellphone number that sent this message. Contents: Click to unfold and read the detailed content of the message. Select: Select the message(s) for deletion. Click All to select all of the messages. Click Refresh to refresh the inbox, and get any new message(s). Click Delete to delete the message(s). 4.3.3 Sentbox Figure 4-6 Sentbox -14- M5350 3G Mobile Wi-Fi User Guide Index: The index of the message. Date: Shows the date when the message was sent. Number: Shows the cellphone number that the message was planned to be sent to. Contents: Click to unfold and read the detailed content of the message(s). Select: Select the message(s) for deletion. Click All to select all of the messages. Click Refresh to refresh the inbox. Click Delete to delete the message(s). 4.3.4 Drafts You can review the unsent saved message(s) on this page. Figure 4-7 Drafts Index: The index of the message. Number: Shows the cellphone number that this message was planned to be sent to. Contents: Click to unfold and read the detailed content of the message(s), or for further edition and delivery. Select: Select the message(s) for deletion. Click All to select all of the messages. Click Refresh to refresh the drafts. Click Delete to delete the message(s). -15- M5350 3G Mobile Wi-Fi User Guide Figure 4-8 Edit Message(Drafts) 4.3.5 Settings On this page, you can do the following settings: Figure 4-9 Settings Enable SMS Center: Disabled by default. It's recommended to keep the default setting. If you want to manually set the SMS Center Number, please select Enable. SMS Center Number: When the SMS Center is enabled, you can enter the SMS Center Number of the local ISP. If you enter a wrong number, the SMS would be affected and not properly used. Save The Sent Message: Enable it to automatically save the sent message in the sentbox. Auto Replace Old Messages: If enabled, it will automatically delete the old messages and save the new ones when the sentbox or drafts box is full. If disabled, you need to -16- M5350 3G Mobile Wi-Fi User Guide manually delete the old messages to save the new ones when the sentbox or drafts box is full. Click Save to make your settings take effect. 4.4 Advanced Figure 4-10 Advanced Menu There are four submenus under the Advanced tab (as shown in Figure 4-10): Dial-up, Wi-Fi, DHCP and Tools. Click any of them, and you will be able to configure the corresponding functions. 4.4.1 Dial-up Figure 4-11 Dial-up Menu 4.4.1.1. Dial-up Dial-up Settings page allows you to do the following configurations. -17- M5350 Figure 4-12 3G Mobile Wi-Fi User Guide Dial-up Settings Profile List: A list of profile(s). Select the profile of your SIM card currently inserted in the device, and then you can manually control the connection status and mode of it. Connection Status: Shows whether the Internet is connected or disconnected at present. Connection Mode: The device provides two modes of connection – Auto and Manual. Please select the connection mode as you need. Auto (Connection): The device will automatically establish connection once it’s started. During the process, if your Internet connection is terminated due to some exterior reasons, the device would automatically attempt connection until it’s successful. This option is suggested, if you have the network service paid by month. Manual (Connection): When you start the device and your computer, or when the connection is terminated during the process, you need to manually dial up for connection, either in here or on the Status page. When you select Manual as your connection mode, you need to specify a MAX Idle Time (5 minutes by default), namely a period of inactivity, after which the device will disconnect your Internet connection, and not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. If you have the network service paid by hour, this option is suggested. Click Save to save the above settings and have them take effect. 4.4.1.2. Profile You can manage your profile on this page. -18- M5350 Figure 4-13 3G Mobile Wi-Fi User Guide Profile Management Profile List: A list of profile(s). Select the profile of your SIM card currently inserted in the device, and then you can view the related information of it. If you find any parameters wrong, you can click New to create a new profile with the right settings (as shown in Figure 4-14). Profile Name: Displays the name of the profile you’ve selected. APN Type: Displays the type of your APN, either Auto or Manual. Auto means the device have dynamic APN, which need not to be specified. Manual means you specify your APN manually. APN: Displays the Access Point Name provided by your ISP. Username/Password: Displays the User Name and Password provided by your ISP. Authentication: Displays the specific authentication type your ISP required. None: Means no authentication is required. PAP: Means your ISP required Password Authentication Protocol, which allows the device to establish authentication with the peer using two handshakes. CHAP: Means your ISP required Challenge Handshake Authentication Protocol, which allows the device to establish authentication with the peer using three handshakes and checking the peer identity periodically. Auto: Means the device have dynamic negotiation with the dialing server and the Authentication Type need not to be specified. Click New to create a new profile. -19- M5350 Figure 4-14 3G Mobile Wi-Fi User Guide New Profile 4.4.1.3. Network Mode Figure 4-15 Network Mode Settings Connection Status: Shows whether the Internet is connected or disconnected at present. Network Mode: The device supports three modes of network connection – Auto, 2G only and 3G only. If your SIM card supports GSM, please select 2G only; if your SIM card supports WCDMA, please select 3G only; if you are not very sure about it, please select Auto and then the device will detect it automatically. Click Save to save your settings. 4.4.1.4. PIN Config You can configure your PIN code on this page. -20- M5350 3G Mobile Wi-Fi User Guide Figure 4-16 PIN Configuration Current Status: Shows whether your PIN code function is enabled or disabled. PIN Function: You can select whether to enable PIN function or not. Once the PIN function is enabled, every time you start the device with this SIM card inserted, you need to enter the PIN code; while if you go to enable the Auto Validate PIN function, it could save you this trouble. PIN Code: You can set a PIN code, not more than 8 characters. Remaining Attempts: Shows how many attempts there are left for you to try entering the PIN code after you failed to enter the right one. You have 3 attempts at most. If you accidentally fail in three attempts, the PIN will be locked and you will be required to enter the PUK code that is written on your SIM card (as shown in Figure 4-17). If the current status of PIN is disabled, you can select Enable PIN and set a PIN code, and then click Apply to make your settings take effect. While, if the SIM current status is PIN enabled and verified, you can select Disable PIN and enter the current PIN code, or select Modify PIN and enter the required parameters to set a new PIN code, and then click Apply to make your settings take effect. -21- M5350 3G Mobile Wi-Fi User Guide Figure 4-17 PIN Configuration - PUK Decode A PUK (PIN Unlocked Key), also known as Personal Unlock Code (PUC), is used in 3GPP mobile phones to reset a personal identification number (PIN) that has been lost or forgotten. The PUK is a SIM-specific code assigned by the service provider. If a user does not know his or her PUC and is prompted for it, it should be obtained from the service provider. On the page as shown in Figure 4-17, first enter the PUK code and then set a new PIN code to unlock your SIM card as well as any device with it inserted. 4.4.1.5. Auto Validate PIN Figure 4-18 PIN Code Auto Validate Auto Validate: Select to enable or disable this function. PIN Code: If you enable the Auto Validate function above, please enter the appropriate PIN code of your SIM card in this filed. When the PIN code is required upon device -22- M5350 3G Mobile Wi-Fi User Guide restarting, it will be validated automatically once. If validation failed, please go to PIN Config page to input another PIN code. Click Save to save your settings. 4.4.2 Wi-Fi Figure 4-19 Wi-Fi menu Wi-Fi Settings can prevent any intruders from connecting your wireless network, occupying your network resources, hacker-overhearing and hacker-attacking, and thus enhance the security of your wireless network. 4.4.2.1. Basic Settings Wi-Fi basic settings enable you to configure your wireless parameters. Figure 4-20 Wi-Fi Basic Settings Wireless Network Name (SSID): SSID is short for Service Set Identification, which is for you to distinguish the different wireless network. The default SSID of this device is TP-LINK_M5_XXXXXX (XXXXXX stand for the last 6 characters of the MAC address of it.) You can rename it as your preference, but the value is limited to 32 characters at most and also it is case-sensitive (For example, TEST is NOT the same as test.) Later on it will displays in the wireless network list searched by your devices. -23- M5350 3G Mobile Wi-Fi User Guide Enable SSID Broadcast: Select to enable or disable this function. When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the device. If you Enable SSID Broadcast, the Wireless device will broadcast its name (SSID) on the air; otherwise, you have to manually type in the SSID and then you can join its network. Region: Select your region from the drop-down list. This field specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. Channel: This field determines which operating frequency ranging from 1~13 will be used. If you select Auto, then the device will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Security Mode: You are provided three modes of security here: None, WPA-PSK/WPA2-PSK, and WEP. WPA-PSK/WPA2-PSK: It’s the WPA/WPA2 authentication type based on pre-shared passphrase. It’s easy to set and secure to use. So it’s perfect for SOHO users. WPA Encryption: Two types of encryption are provided here: TKIP and AES. AES is recommended. WPA Key: The default WPA key is the last 8 characters of IMEI. You can keep it default or enter 8~63 ASCII characters or 8~64 hexadecimal characters as your new WPA key. WEP: Wired Equivalent Privacy, a basic type of security, is not so secure as WPA-PSK/WPA2-PSK. It is based on the IEEE 802.11 standard. WEP Authentication Type: Select either Open (System) or Shared (Key) as your authentication. WEP Key Type: HEX and ASCII formats are provided. HEX format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length. WEP Key Lengths: You can select the WEP key length WEP_40 (64-bit) or WEP_104 (128-bit) for encryption. You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters for WEP_40 (64-bit).You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters for WEP_104 (128-bit). WEP Key: In accordance with the WEP Key length you have selected above, enter your WEP Key. -24- M5350 3G Mobile Wi-Fi User Guide Wi-Fi off time: If no clients connect to the device’s wireless network in a period of time (15 minutes by default), the Wi-Fi will be shut down. You can press the power button to resume the Wi-Fi. Click Save to save your settings. 4.4.2.2. MAC Filter The Wireless MAC Address Filtering feature allows you to control the wireless stations accessing the device, which depends on the station's MAC addresses. MAC Address is the physical address of the wireless stations, usually in the format of XX-XX-XX-XX-XX-XX format (X is any hexadecimal digit). Figure 4-21 Wireless MAC Filter Wireless MAC Filter: Select to Enable or Disable the MAC filter function of the device. The below settings will take effect only when you select Enable. MAC Address List: A List of MAC addresses will be allowed to access the device. Your MAC: Displays the MAC address of your client(s) currently wirelessly connected to the device. Click Save to save your settings. 4.4.2.3. Wi-Fi Status The Wi-Fi Status page displays the basic information about the Wi-Fi client(s) that are currently connected to the device. -25- M5350 3G Mobile Wi-Fi User Guide Figure 4-22 Wi-Fi Status ID: The index of the Wi-Fi Client. MAC Address: The MAC address of the Wi-Fi client. Click Refresh to update the amount of the Wi-Fi clients and their information. 4.4.3 DHCP Figure 4-23 DHCP menu The Device is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the wireless clients that are connected to the device in the LAN. -26- M5350 4.4.3.1. 3G Mobile Wi-Fi User Guide Basic Settings Figure 4-24 Basic Settings IP Address: The IP address of the device, which is used to log in its web-based management page. The default value is 192.168.0.1. Subnet Mask: An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. DHCP Server: You can select to enable or disable the DHCP server. If you disable the server, you must have another DHCP server within your network, or else you must configure the IP address of the host(s) manually. Start IP Address: This field specifies the first address in the IP address pool. 192.168.0.100 is the default start IP address. End IP Address: This field specifies the last address in the IP Address pool. 192.168.0.199 is the default end IP address. Address Lease Time: It is the length of time a network user will be allowed to keep connecting to the device with the current IP address (that is assigned by the DHCP server). Enter the amount of time, in minutes, that the IP address will be "leased". The time range is 1~2880 minutes. The default value is 120 minutes. Preferred DNS Server: Input the DNS IP address provided by your ISP. It is optional. Alternate DNS Server: Input the IP address of another DNS server if your ISP provides two DNS servers. It is optional. Click Save to save the changes. Note: To use the DHCP server function of the Device, you should configure all the clients in the LAN as "Obtain an IP Address automatically" mode. -27- M5350 3G Mobile Wi-Fi User Guide 4.4.3.2. Clients List On this page, you can view the information about the clients attached to the device. All the information is read-only. You cannot change any of the values on this page. Figure 4-25 Clients List ID: The index of the DHCP Clients. Host Name: The name of the DHCP client(s). MAC Address: The MAC address of the DHCP client(s). IP Address: The IP address the device has assigned to the DHCP client(s). Duration: The time of the DHCP client(s) leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the client(s). 4.4.4 Tools Figure 4-26 Tools menu Under Tools menu, you can do such configurations as backing up or uploading a configuration file of the device, restoring all the settings of the device to its factory defaults, modifying the password for your login, rebooting the device, and checking some information about the device. As follows, we will explain them in details. -28- M5350 3G Mobile Wi-Fi User Guide 4.4.4.1. Configuration On this page, you can back up the configuration of the device to file, or upload a configuration file to the device. Figure 4-27 Configuration Management Backup Configuration to File: Click Backup to save the configuration file in your computer, for later necessary use. It’s strongly recommended to back up the old configuration file before firmware upgrade or new configuration file upload, in case that during those process it might get the original configuration lost. Upload Configuration File: Click Browse to locate the config.bin file or directly enter its location file, and then click Upload to upload the configuration file. 4.4.4.2. Restore Factory You can restore the device to its factory default settings, when necessary. Figure 4-28 Restore to factory defaults -29- M5350 3G Mobile Wi-Fi User Guide Restore to Factory Defaults: Click Restore to reset all configuration settings to their default values. All of the settings you have saved will be lost when the default settings are restored. You can restore the following factory default values: • The default User Name: admin • The default Password: admin • The default IP Address: 192.168.0.1 • The default Subnet Mask: 255.255.255.0 4.4.4.3. Modify Password It is strongly recommended that you change the factory default password of the device. Figure 4-29 Modify Password Old Password: The old password that is used to log in the device. New Password: The new password you want to set for the login of the device. Confirm New Password: Enter the new password again for confirmation. Click Save when you finish the setting. Click Clear to clear all the values you have already set, and then you can reset it. Note: The new password must not exceed 14 characters in length and not include any spaces. -30- M5350 3G Mobile Wi-Fi User Guide 4.4.4.4. Reboot Figure 4-30 Reboot the Device Reboot the Device: Click Reboot to get the device rebooted and the saved settings to take effect. 4.4.4.5. Device Info This page displays the related information about this device, including Device Name, Firmware Version, Hardware Version, MAC Address, and IMEI. Figure 4-31 Device Information Device Name: The Model of the device. Firmware Version: The current firmware version Hardware Version: The current hardware version. MAC Address: The physical address of the device. The value is read-only thus could not be changed. IMEI: International Mobile Equipment Identity. Composed of 15 digits, it is unique and thus used to identify individual mobile equipment. -31- M5350 3G Mobile Wi-Fi User Guide Appendix A: FAQ T1. What should I do if I cannot log in the web-based management page of M5350 after I have successfully connected to M5350? 1) Please verify your PC‘s IP address is on the same network segment with M5350. If not, please go to the next step. 2) Manually set an IP address for your PC, or configure your PC to “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Thus to make sure your PC‘s IP address on the same network segment with M5350. 3) If the above two steps failed, please feel free to contact our technical support. T2. What should I do if I cannot access the Internet? 1) Please verify the card you inserted into M5350 is a valid WCDMA SIM card. 2) Please check if the PIN function is enabled. If enabled, please go to Advanced -> Dial-up -> PIN Config and enter the correct PIN code. 3) Please verify the current ISP parameters are correct. Otherwise, please go to Advanced -> Dial-up -> Profile and configure the correct parameters. 4) Please check if the connection mode is auto or manual. If it is manual connection, please go to Advanced -> Dial-up and click Connect to manually get connected to the Internet. 5) If the above steps failed, please feel free to contact our technical support. T3. What if I forget my login password? 1) Restore M5350 to its factory defaults; 2) Log into M5350 with the default user name and password: admin. And then reconfigure M5350 following the QIG. T4. How could I restore M5350 to its factory defaults? Method 1: With M5350 powered on, use a pin to press the RESET button in the interior panel. Method 2: Get logged in to the web-based management page of M5350, and then go to Advanced -> Tools -> Restore Factory and click Restore. Note: Once M5350 is reset, all the current configurations will be lost and you need to reconfigure it. -32- M5350 3G Mobile Wi-Fi User Guide Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. 1. Install TCP/IP component 1) On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel. 2) Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window. 3) Right click the icon that showed below, select Properties on the prompt page. Figure B-1 4) In the prompt page that showed below, double click on the Internet Protocol (TCP/IP). Figure B-2 -33- M5350 5) 3G Mobile Wi-Fi User Guide The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. You have two ways to configure the TCP/IP protocol below: Setting IP address automatically Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as shown in the Figure below: Figure B-3 Setting IP address manually a. Select Use the following IP address radio button. And the following items available b. If the Device's LAN IP address is 192.168.0.1, type IP address is 192.168.0.x (x is from 2 to 254), and Subnet mask is 255.255.255.0. c. Type the Device’s LAN IP address (the default IP is 192.168.0.1) into the Default gateway field. d. Select Use the following DNS server addresses radio button. In the Preferred DNS Server field you can type the DNS server IP address, which has been provided by your ISP. -34- M5350 Figure B-4 6) Now click OK to keep your settings. -35- 3G Mobile Wi-Fi User Guide M5350 3G Mobile Wi-Fi User Guide Appendix C: Specifications General Standards IEEE 802.11n, IEEE 802.11b, IEEE 802.11g Network Type HSPA+ / HSUPA / HSDPA / UMTS Certification CE, FCC, RoHS Dimension 94mm x 56.7mm x 19.8mm (W x D x H) One Micro USB port One SIM card slot Interface One Micro SD Memory card slot Power button RESET button OLED Display Power Supply 2000m Internal Ah Rechargeable Battery 5VDC/1.0A External Power Adapter Wireless Band Data Rate WCDMA: 2100/1900/900Mhz GSM: 850/900/1800/1900Mhz Download: 21.6Mbps Upload: 5.76Mbps Frequency 2.4-2.4835GHz EIRP <20dBm Security 64/128-bit WEP, WPA-PSK/WPA2-PSK Antenna Internal Antenna Environment Temperature Humidity Operating : 15℃~40℃ Storage: -20℃~50℃ Operating: 0% ~ 75% RH, Non-condensing Storage: 0% ~ 75% RH, Non-condensing Attention：All the 3G function described above is not available in the United States. 3G Function is designed for other countries except the Unites States. -36- M5350 3G Mobile Wi-Fi User Guide Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.11n development process and promote a technology specification for interoperability of next-generation wireless local area networking (WLAN) products. 802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security. DHCP (Dynamic Host Configuration Protocol) - A protocol that automatically configure the TCP/IP parameters for the all the PC(s) that are connected to a DHCP server. ISP (Internet Service Provider) - A company that provides access to the Internet. SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit shared key algorithm, as described in the IEEE 802.11 standard. Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices. WLAN (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area. -37-
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Annotate, Fill forms Tagged PDF : Yes Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2013:12:23 15:07:48+08:00 Create Date : 2013:01:28 09:17:16+08:00 Metadata Date : 2013:12:23 15:07:48+08:00 Creator Tool : Adobe Illustrator CS3 Thumbnail Width : 148 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 13454 bytes, use -b option to extract) Document ID : uuid:e9d8dc59-c794-4ffc-aa91-c44c5cef3158 Instance ID : uuid:d59fbf34-faf9-4457-99c8-ace7d64fa7aa Rendition Class : proof:pdf Subject : 506 Format : application/pdf Title : Description : Creator : Producer : Adobe PDF Library 10.0 N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 8.268338 Max Page Size H : 11.693332 Max Page Size Unit : Inches Font Name : ArialMT, Arial-BoldMT, AdobeSongStd-Light, SimSun Font Family : Arial, Arial, Adobe 宋体 Std, 宋体 Font Face : Regular, Bold, L, Regular Font Type : Open Type, Open Type, Open Type, TrueType Font Version : Version 3.00, Version 3.00, Version 5.002;PS 5.002;hotconv 1.0.49;makeotf.lib2.0.15106, Version 3.12 Font Composite : False, False, False, False Font File Name : ARIAL.TTF, ARIALBD.TTF, AdobeSongStd-Light.otf, simsun.ttc Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Page Count : 44 Page Layout : OneColumnEXIF Metadata provided by EXIF.tools