TP Link Technologies RE580D AC1900 Wi-Fi Range Extender User Manual
TP-Link Technologies Co., Ltd. AC1900 Wi-Fi Range Extender
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2823621 |
| Application ID | DFUX3YEdulUZtP515x5BzQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 126.39kB (1579902 bits) |
| Date Submitted | 2015-11-26 00:00:00 |
| Date Available | 2015-11-26 00:00:00 |
| Creation Date | 2015-11-25 16:16:27 |
| Producing Software | Microsoft® Word 2013 |
| Document Lastmod | 2015-11-25 16:16:27 |
| Document Title | User Manual |
| Document Creator | Microsoft® Word 2013 |
| Document Author: | win7 |
1910011262 REV 1.0.0 Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright ©2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be colocated or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 26 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” This device is restricted in indoor environment only. This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. surface. The device complies with RF specifications when the device used at 20 cm from your body. 2. SRD with DSSS and other than FHSS wideband modulation 1.3.Maximum applications. 100 mW e.i.r.p. Indoor 2.1. Maximum mean e.i.r.p. density is 2 mW/MHz. Maximum 100 mW e.i.r.p. 2.2. Maximum mean e.i.r.p. density is 20 mW/MHz. Maximum 100 mW e.i.r.p. It is permitted to use SRD for outdoor applications only for purposes of gathering telemetry information for automated monitoring and resources accounting systems or security systems. This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Belarus Not implemented Norway Implemented Reason/remark This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund on Svalbard. Italy Implemented The public use is subject to general authorisation by the respective service provider. Russian Federation Limited implementation 1. SRD with FHSS modulation 1.1. Maximum 2.5 mW e.i.r.p. 1.2. Maximum 100 mW e.i.r.p. Permitted for use SRD for outdoor applications without restriction on installation height only for purposes of gathering telemetry information for automated monitoring and resources accounting systems. Permitted to use SRD for other purposes for outdoor applications only when the installation height is not exceeding 10 m above the ground 2.3. Maximum mean e.i.r.p. density is 10 mW/MHz. Maximum 100 mW e.i.r.p. Indoor applications. Ukraine Limited implementation e.i.r.p. ≤100 mW with built-in antenna with amplification factor up to 6 dBi. ATTENTION: Due to EU law, the country settings must be identical to the country where the device is operating (important due to non-harmonised frequencies in the EU). Restricted to indoor use. This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : l'appareil nedoit pas produire de brouillage, et 5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This radio transmitter (IC: 8853A-RE580D / Model: RE580D) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list (Appendix), having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC: 8853A-RE580D / Model: RE580D) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste (Annexe), et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; The maximum antenna gain permitted for devices in the band 5725- Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; Le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et l’exploitation non point à point, selon le cas; De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.à-d., qu’ils ont la priorité) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 32cm between the radiator & your body. 減少電磁波影響，請妥適使用。 安全諮詢及注意事項 Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 32 cm de distance entre la source de rayonnement et votre corps. ● ● ● ● CAN ICES-3 (B)/NMB-3(B) ● 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行 清潔。 注意防潮，請勿將水或其他液體潑灑到本產品上。 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞 或覆蓋開口。 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在 密閉位置中。 당해 무선설비는 운용중 전파혼신 가능성이 있음. ● 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進 行此項工作。 注意！ 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用 者均不得擅自變更頻率、加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現 有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通 信，指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、 科學以及醫療用電波輻射性電機設備之干擾。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. ● ● When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. ● Avoid water and wet locations. ● Adapter shall be installed near the equipment and shall be easily accessible. ● The plug considered as disconnect device of adapter. ● Use only power supplies which are provided by manufacturer and in the original packing of this product. This product can be used in the following countries: AT BG BY CA CZ DE DK EE ES FI FR GB GR HU IE IT LT LV MT NL NO PL PT RO RU SE SG SK TR UA US TP-LINK TECHNOLOGIES CO., LTD The product carries the CE Mark: For the following equipment: Product Description: AC1900 Wi-Fi Range Extender Person responsible for marking this declaration: Model No.: RE580D Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents Yang Hongliang EN 300 328 V1.8.1: 2012-06 Product Manager of International Business EN 301 489-1 V1.9.2:2011& EN 301 489-17 V2.2.1:2012 Date of issue: 2015-06-19 EN 55022:2010+AC:2011 EN 55024:2010 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 EN 50385:2002 EN 301 893 V1.7.1:2012-06 TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China Contents Introduction........................................................................1 Product Overview ..................................................................... 1 What can your Extender do .................................................. 1 Support for the 802.11ac wireless technology ..................... 1 Main Features....................................................................... 2 Appearance .............................................................................. 2 Connect the Extender to the Internet .................................4 Before You Begin ..................................................................... 4 Basic Requirements ................................................................. 5 Quick Setup .............................................................................. 5 Using WPS (Wi-Fi Protected Setup) .................................... 5 Using your Web Browser...................................................... 7 View the Information of the Extender .............................. 11 View the Extender’s Current Status ....................................... 11 Change the Extender’s IP Address ........................................ 19 DHCP Server .......................................................................... 19 Settings ............................................................................... 19 View the DHCP Client List .................................................. 20 More Functions ............................................................... 22 Entertainment Adapter ............................................................ 22 Manage the Extender ..................................................... 23 LED Control ............................................................................ 23 Firmware Upgrade .................................................................. 24 Backup & Restore ................................................................... 24 Factory Defaults ...................................................................... 25 System Log ............................................................................. 25 Reboot .................................................................................... 26 Logout ..................................................................................... 26 View the Information about the Host Network, the Extender and the Clients .............................................................................. 12 Appendix......................................................................... 27 Manage the Extended Network and Security Settings .... 13 Factory Defaults ...................................................................... 27 Extend another Network ........................................................ 13 Troubleshooting ...................................................................... 28 Extender Settings ................................................................... 15 Specifications .......................................................................... 29 Manage the Extender’s Wi-Fi Security Settings .................... 16 Glossary .................................................................................. 29 Change your Admin Account ............................................. 16 Control the Wireless Devices Access to the Extender....... 16 The RE580D AC1900 Wi-Fi Range Extender is dedicated to Small Office/Home Office (SOHO) wireless network solutions. It will enlarge your existing wireless network and mobility within your wireless network while also allowing you to connect a wired device to a wireless environment. Increased mobility and the absence of cabling will be beneficial for your network. The extender provides two options to finish the quick setup. This chapter covers the following topics: Product Overview Option One: an easy wireless connection to the host network (equipped with WPS/QSS button) by Using WPS on the back panel. Appearance Option Two: Using your Web Browser for installation and management. Even though you may not be familiar with the extender, you can easily configure it with the help of this guide. Before installing the extender, please look through this guide to get the full information of the RE580D AC1900 Wi-Fi Range Extender. With using IEEE 802.11ac wireless technology, this device can transmit wireless data at the rate of up to 600Mbps (2.4GHz) + 1300Mbps (5GHz). With multiple protection measures, including wireless LAN 64/128-bit WEP encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), the RE580D AC1900 Wi-Fi Range Extender delivers complete data privacy. It is also compatible with all IEEE 802.11n, IEEE 802.11a, IEEE 802.11b and IEEE 802.11g products. Introduction Complies with IEEE 802.11ac Provides multiple encryption security Types including: 64/128-bit WEP and WPA-PSK/WPA2-PSK Supports Built-in DHCP server Supports Firmware Upgrade Supports Web-based Management LEDs Ports Buttons Introduction Name (RE) Status Indication Solid blue The extender has established a secure connection, and the signal strength is adequate. Solid orange Blinking (5GHz)/ (2.4GHz) (Power) (Ethernet) (Range Extender/WPS) Button: If your Wireless router supports WPS or QSS function, you can press the WPS or QSS button and then press the RE button to establish a secure connection between the Wireless router and the extender. Reset Button: This button is used to restore the extender’s factory default settings. The extender has established a secure connection, but the signal strength is too weak. There are two ways to reset the extender: Option One: With the extender powered on, use a pin to press the RESET button until all the LEDs turn on momentarily, then release the button and wait the extender to reboot to its factory default settings. WPS connection is in process. Off No active connection. On The extender is connected to the 2.4GHz or 5GHz wireless network of your host network. Off No connection. On The extender is on. Option Two: Restore the default settings from System Tools > Backup &Restore of the extender's Web-based Management page. LED Button: You can press the LED button to light up or turn off all the LEDs. After the LEDs are off, the extender can still work normally. The extender is initializing. Power Button：You can press the Power button to turn on or off the extender. Off The extender is off. On The Ethernet port is connected. Off The Ethernet port is not connected. Ethernet Port: Five 10/100/1000Mbps RJ45 Ethernet ports used to add wireless connectivity to an Ethernet-enabled device such as Internet TV, DVR, Gaming console and so on. Please note that this port is not allowed to be connected with router. Blinking Introduction Please read this guide carefully before installing and using the device. The operating distance range of your wireless connection can vary significantly depending on the physical position of the wireless devices. Factors that can weaken signals by getting in the way of your network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary based on the types of materials and background RF (radio frequency) noise in your home or office. In order to optimize the performance of RE580D, please follow the instructions below to achieve an ideal location (please make sure it is always within the wireless coverage of the wireless router). ● Half-way Between Generally, the ideal location for RE580D is half-way between the Wireless router and Wireless Client. If the wireless signal is not satisfactory, you may place RE580D somewhat nearer to the Wireless router. ● No Obstacles and Spacious - Clear obstacles in the way between RE580D and Wireless router. It’s better to locate it in a spacious place, such as near the corridors. ● No Interference - Choose a location away from Bluetooth devices and other household electronics, such as cordless phone, microwave, and baby monitor, etc., to minimize signal interference. This chapter covers the following topics: Before You Begin Basic Requirements Quick Setup Connect the Extender to the Internet Your router should support WPS. Otherwise, please use Using your web browser. Place your extender in a well-ventilated place far from direct sunlight, any heater or heating vent. Leave at least 2 inches (5cm) space around the device for heat dissipation. Turn off your extender and unplug the power adapter in a lighting storm to avoid damage. Use Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0 or above. Operating temperature of the extender should be 0℃~40℃ (32℉ ~104℉). Operating humidity of the extender should be 10%~90%RH (Noncondensing). Power On Plug the extender into an electrical outlet near your router, and wait until the Power LED is lit and solid blue. Connect Press the WPS button on your router. Connect the Extender to the Internet If the RE LED does not change from flashing to solid, please refer to Using your Web Browser. Some ISP gateways disable the WPS function by default, if the WPS method fails, please refer to Using your Web Browser. If you are connecting the extender to a dual-band router but only 2.4GHz ( ) or 5GHz ( ) LED is on, repeat step 1) and 2) again to connect the other band. For more information about using WPS on your router, please refer to the router manufacturer's user guide. Immediately press the RE button on your extender. The LED should change from flashing to solid, showing that WPS connection is successful. Relocate Plug the extender into an electrical outlet about halfway between your router (Host Network) and the Wi-Fi dead zone. Wait until the LED is lit with a solid blue. If not, relocate the extender closer to the router to achieve a good (or better) signal quality. Enjoy! The extender shares the same wireless network name (SSID) and wireless password as your router. Connect the Extender to the Internet Power On Plug the extender into an electrical outlet near your router, and wait until the Power LED is lit and solid blue. ● Connecting via Wireless Disconnect the Ethernet (wired) connection to your computer. Click the Wi-Fi icon on the taskbar and connect to the extender's network (e.g. TPLINK_Extender_2.4GHz or _5GHz). Connect to the Extender ● Connecting via Ethernet Cable Disable the Wi-Fi on your computer. Connect the extender to your computer via an Ethernet cable. Login Launch a web browser and type http://tplinkrepeater.net into the URL field and use admin (all lowercase) for both Username and Password to log in. Connect the Extender to the Internet Configure Create a new username and password to log in the web management page, then click Confirm. Select your router's 2.4GHz host network and enter the password, then click Next. Select your router's 5GHz host network and enter the password, then click Next. Connect the Extender to the Internet Verify your wireless settings and click Finish. The corresponding LEDs (2.4GHz and 5GHz) should turn on and stay solid. If your router does not support 5GHz wireless network, please click Skip to continue. Either keep the same SSIDs as your host network or create new names for the extended networks, then click Next. Connect the Extender to the Internet Enjoy! Both extended networks share the same Wi-Fi password as your main network, but may have different wireless network names if you customize the SSIDs during the configuration. Relocate Plug the extender into an electrical outlet about halfway between your router (Host Network) and the Wi-Fi dead zone. Wait until the LED is lit with a solid blue. If not, relocate the extender closer to the router to achieve a good (or better) signal quality. Connect the Extender to the Internet Launch a web browser and type in http://tplinkrepeater.net, then go to Settings > Status webpage. You can view the network connection in the Status webpage. ● The normal status. ● The extender is failed to connect to the wireless network of your router. ● The extender is connected to the wireless network of your router, but no transmitting data. Please check your host network. ● The extender is connected to the router unnormally. Maybe the gateway is set incorrectly in the Static IP. You can select “Obtain an IP address automatically” on the “LAN Settings” page. This chapter covers the following topics: View the Extender’s Current Status View the Information about the Host Network, the Extender and the Clients View the Information of the Extender Instructions for the icons of 2.4GHz/5GHz wireless status: Name Instructions The wireless is on and encrypted. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings > Status webpage. Click the icons of your router, the extender and clients. The detailed instructions for the corresponding icon are displayed below. The wireless is on and unencrypted. Router：The wireless is off, or the connection is failed. Extender：The wireless is off. The icons are selected. View the Information of the Extender If you want to extend another network, you can refer to the following steps to finish it quickly. Launch a web browser and type in http://tplinkrepeater.net，then go to Settings->Wireless->Connect to Network webpage. Enable Connect to 2.4GHz/5GHz Network. Then click Wireless Scanner to scan the network you want to extend. This chapter covers the following topics: Extend another Network Extender Settings Manage the Extender’s Wi-Fi Security Settings Change the Extender’s IP Address DHCP Server Manage the Extended Network and Security Settings Select the network you want to extend from the list. Once a network is selected, the SSID and security settings of that network will automatically fill in. If the host network is encrypted, enter the password in the box of the host wireless security. If the network you want to extend is on but not shown in the list, please try by following the steps below. Move the extender closer to your router. Then click Refresh on the top-right corner of the list to scan the network again. You can also enter the information of the network manually you want to extend on the Connect to Network page. Then click Save to connect to the host network. When Host 2.4GHz/5GHz Security is WEP, please select the index same with the host network. Click Save to save the settings. Manage the Extended Network and Security Settings Relocate. Plug in the extender halfway between your wireless router (Host Network) and the Wi-Fi dead zone. Wait for the extender to reconnect and the LED turns solid blue. If not, relocate it closer to the router to achieve a good (or better) signal quality. Enjoy! The extender shares the same wireless network name (SSID) and wireless password as your host network. If you want to change the wireless network name (SSID), please refer to Extended Settings. On the Extended Network page, you can enable or disable the wireless network of the extender, change and hide the wireless network name (SSID) of the extender. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Wireless-> Extended Network webpage. Configure the settings as shown in the figure below. Extended 2.4GHz/5GHz: Enable or disable the 2.4GHz/5GHz wireless function of the extender. Extended 2.4GHz/5GHz SSID: Either copy the host SSID or create a new name using up to 32 characters. This field is case-sensitive. Hide SSID broadcast: Select this checkbox if you want to hide the extender’s SSID (of the 2.4GHz or 5GHz wireless network) from the Wi-Fi network list. If you want to connect to the hiden SSID, please enter the SSID and the password manaully. Click Save to save the settings. Manage the Extended Network and Security Settings Manage the Extender’s Wi-Fi Security Settings Change your Admin Account Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->System Tools->Admin Account webpage. Create a new username and password as shown in the figure below. Click Save to save the settings. Control the Wireless Devices Access to the Extender The Access Control function controls the devices connected to the extender by the wireless connection. For increased security, you can restrict access to the Wi-Fi network of your extender to allow only specific Wi-Fi devices in the white list. Devices that are in the black list cannot join the wireless network of the extender. Blacklist Mode The devices in the Blacklist are not allowed to connect to the extender. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Wireless-> Access Control webpage. Click the button to enable the Access Control function. Old Username：Enter your current username. Old Password: Enter your current password. New Username: Enter your new username. New Password: Enter your new password. Confirm Password: Re-enter your new password. Select Blacklist as shown in the figure below, then click Save to save the settings. Manage the Extended Network and Security Settings Add the device to the blacklist by following the ways. ● Add the Online Devices to the blacklist. In the Online Devices list, you can view the information about the devices connected to the extender. For one device, you can click the icon to add the device to the blacklist. For several devices, select them and click Block to add them at the same time. Device Name: Enter the device name. MAC Address: Enter the MAC address of the host in XX-XX-XX-XXXX-XX format (e.g. 00-11-22-33-44-AA). Click OK to save your settings. Whitelist Mode Only the devices in the Whitelist are allowed to connect to the extender. ● Add the device to the blacklist manually, if the device is not in the Online Devices list. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Wireless-> Access Control webpage. Click the button to enable the Access Control function. Click Add. Then enter the device name and MAC address in the figure below. Select Whitelist as shown in the figure below, then click Save to save the settings. Manage the Extended Network and Security Settings Click OK to save your settings. Modify or Remove a Device in the Blacklist/Whitelist Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Wireless-> Access Control webpage. Click the Add button. You can modify or remove the devices in the Blacklist or Whitelist. ● Modify a Device in the Blacklist or Whitelist. Click the icon , and then enter the device name and MAC address. Click OK to save the setings. ● Device Name: Enter the device name. MAC Address: Enter the MAC address of the host in XX-XX-XX-XXXX-XX format (e.g. 00-11-22-33-44-AA). Remove a Device in the Blacklist or Whitelist. For one device, you can click the icon to remove the device from the list. For several devices, select them and click Delete to remove them at the same time. Manage the Extended Network and Security Settings Change the Extender’s IP Address By default, the extender is set to obtain an IP address automatically from the front router. If you want to use a specific IP address appropriate to your network demand, please refer to the steps below. We do NOT recommend you change the IP address unless you are quite sure about the IP setting for special network demand, random changes may lead to Internet disconnection. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Network webpage. Select Use the following IP address, then enter the IP address and gateway manually. Subnet: Enter the subnet mask in dotted-decimal notation that determines the size of the network (255.255.255.0 by default). Default Gateway: Enter the gateway that is in the same subnet as the IP address in dotted-decimal notation. It is usually the LAN IP address of your router. Click the Save button to save the settings. DHCP Server DHCP stands for Dynamic Host Configuration Protocol. The DHCP Server will automatically assign dynamic IP addresses to the devices on the network. This protocol simplifies network management and allows new wireless devices to be set to IP addresses automatically. To use the DHCP server function of the device, you should configure all computers as "Obtain an IP Address automatically" mode. Settings ● IP Address: Enter the IP address in dotted-decimal notation (192.168.0.254 by default). Set the DHCP Server status to Auto (by default) When the DHCP Server is Auto, the extender automatically detects to find the devices enabling the DHCP Server. If the DHCP Server of the device is enabled, the extender’s DHCP Server is disabled. Otherwises, the extender’s DHCP Server is enabled. The default is Auto. ● Enable DHCP Server Manage the Extended Network and Security Settings When the DHCP Server is On, please make sure that IP Address Pool, Default Gateway for the DHCP server and LAN IP address are in the same segmengt as the router. Otherwises, the extender cannot access the Internet. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Network webpage. If the DHCP Server is On, please configure it as shown in the figure bleow. Primary DNS (Optional): Enter the DNS IP address provided by your ISP. Secondary DNS (Optional): Enter the second DNS IP address provided by your ISP. Click Save to save your changes. ● Disable DHCP Server If the DHCP server of the extender is Off, please make sure the DHCP server of your router is on. Otherwise, you have to configure the IP address for each client manually. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Network webpage. Select Off, then click Save to save the settings. View the DHCP Client List The DHCP Client List displays the Client Name, MAC Address, Assigned IP and Lease Time for each DHCP Client attached to the device. IP Address Pool：Enter a range of IP address that can be leased to the clients. By default, the starting IP address is 192.168.0.100 and the ending IP address is 192.168.0.199. Address Lease Time：Enter the time duration that an IP address is leased to the client, between 1 and 2880 minutes. The default is 1 minute. Default Gateway (Optional): Enter the LAN IP address of your host network. Launch a web browser and type in http://tplinkrepeater.net, then log in to Settings->Network webpage. You can view the information of the DHCP clients connected to the extender in the DHCP Client List. Manage the Extended Network and Security Settings Client Name: The name of the DHCP client. MAC Address: The MAC address of the DHCP client. Assigned IP Address: The IP address that is allocated to the client by the DHCP server. Lease Time: The time duration that the IP address is leased to the DHCP client. Click Refresh to refresh the DHCP Client List. Manage the Extended Network and Security Settings The extender RE580D can be used as a wireless adapter to connect any Ethernet-enabled device, such as a Blu-ray player, game console, DVR, or smart TV, to your wireless network. After the extender connected to the Internet, you can connect an Ethernetenabled device to the extender using an Ethernet cable. This chapter covers the following topics: Entertainment Adapter By default, the Ethernet ports connect to the 5GHz wireless network. If you want the extender to connect to the 2.4GHz wireless network only, please follow the steps below to finish the settings: Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Network webpage. Select the radio button 2.4GHz in the following figure. Click Save to save the settings. More Functions LED Control can turn off the LEDs at the specific time. The extender can still work normally after the LEDs are off. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings-> System Tools -> Time Settings webpage. Select the Time Zone of your location. Click Save to save your settings. This chapter covers the following topics: LED Control Firmware Upgrade Backup & Restore Factory Defaults System Log Reboot Logout Go to Settings-> System Tools -> LED Control webpage, then set the time to turn off the LEDs. ● Night Mode：If the Night Mode box is checked, all the LEDs are off in the setting time. Manage the Extender ● LED Off Time: Set the time to turn off the LEDs. Please DO NOT power off the extender during the upgrade process. Click Save to save your settings. Launch a web browser and type in http://tplinkrepeater.net，then go to Settings->System Tools->Firmware Upgrade webpage. You can view the firmware version and the software version. Search the latest firmware of your extender from the Support page at www.tplink.com. Then download the latest firmware upgrade file to your computer. It is highly recommended to backup your current configurations, in case a recovery is needed to restore the system to a previous state or from the factory defaults. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->System Tools->Backup & Restore webpage. Click Browse to locate and select the downloaded file. Backup and restore the configuration on the Backup & Restore page. ● Configuration Backup Click Backup to save your current configurations as a config.bin file on your computer. Make sure to save it in a safe location where you can retrieve it when needed. Click Upgrade. The upgrade takes a few minutes to complete and the extender will automatically reboot itself when finished. Manage the Extender Please DO NOT power off the extender during the backup process. ● Configuration Restore Click Browse to locate and select your backup file. Click Restore and then YES to restore the extender. The restore process may take a few minutes to complete and the extender will automatically reboot itself when finished. Please DO NOT power off the extender during the restore process. Factory Restore will erase all settings that you have configured for the extender. To re-login to the extender's management page, use the default admin for both username and password. Launch a web browser and type in http://tplinkrepeater.net，then go to Settings->System Tools-> System Log webpage. You can select the Log Type and Log Level in the Log Filter drop-down list. Here you can quickly trace the logs which you want to view. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->System Tools-> Backup & Restore webpage. Click Factory Restore to reset your extender to its factory default settings in the figure below. Manage the Extender Launch a web browser and type in http://tplinkrepeater.net. Click Reboot on the top right corner to reboot the extender. Launch a web browser and type in http://tplinkrepeater.net. You can also click the following buttons to apply the settings. Click Refresh to update the system log. Click Delete All to permanently remove all logs. Click Save Log to save the system log as a .txt file on your computer. Click Logout on the top right corner to log out the management webpage safely. Manage the Extender Name Status Common Default Settings This chapter covers the following topics: Username admin Password admin IP Address 192.168.0.254 Subnet Mask 255.255.255.0 http://tplinkrepeater.net Factory Defaults Domain Troubleshooting Wireless Specifications Glossary 2.4GHz: TP-LINK_Extender_2.4GHz SSID 5GHz: TP-LINK_Extender_5GHz Wireless Security Disabled Access Control Disabled Appendix browser, enter the default domain http://tplinkrepeater.net in the address field and get logged in. If you are unable to log in, please RESET the device, and then use the default IP address to get into the web-based configuration page, reconfigure the device. T1. How do I restore my extender’s configuration to its factory default settings? ● There are two ways to reset the extender: ● ● Option One: With the extender powered on, use a pin to press and hold the RESET button until all LEDs turn on momentarily, then release the button. Option Two: Restore the default settings from “System Tools > Restore & Backup” of the extender's Web-based Management page. Once the extender is reset, the current configuration settings will be lost and you will need to reconfigure it. T2. What can I do if I forget my login password? ● Restore the extender’s configuration to its factory default settings. If you don’t know how to do that, please refer to previous T1; ● Use the default username and password: admin, admin; ● Try to reconfigure your extender by following the instructions of this guide. T3. What can I do if I cannot access the web-based configuration page? ● Check to verify all the connections (either wireless or wired ones) are proper. If yes, please proceed to the next step; otherwise, check the connections again. ● Try to obtain an IP address and gateway; if succeed, open your web- Feel free to contact our technical support, if the problem still persists. T4. How can I know that my wireless signal has been repeated and boosted by RE580D? An easy way is to compare the signal strength of your target wireless network (symbolized by its SSID), with RE580D in operation vs. out of operation. Before comparison, you’d better make sure your computer can obtain an IP address from your target wireless network and thus access the Internet, either via RE580D or without. T5. Will the extender work if I connect the ETHERNET port of it to the router via Ethernet cable? Sorry, it won’t work. The extender is designed to connect wirelessly to the router, while the ETHERNET port is designed to connect with a wired device, like Internet TV, Gaming console, DVR and so on. T6. Why does the wireless transmission rate speed down, while the wireless signal is stronger after repeated by RE580D? In compliance with the wireless transmission protocol, all the extender devices are set to work in half-duplex instead of full-duplex mode. In other words, the extender has to process one-way communication between your root Wireless router (or AP) and the terminal clients; so the transmission time will be double-increased, while the speed will be decreased. TP-LINK recommends that you connect to the extender when your home network connection is poor, or when you want a larger wireless coverage to eliminate “dead zones”. Appendix Security Physical and Environment General Standards and Protocols IEEE 802.3, IEEE 802.3u, IEEE 802.11a, IEEE 802.11n, IEEE 802.11b, IEEE 802.11g, IEEE 802.1x, IEEE 802.11e, IEEE 802.11i, IEEE 802.11ac, TCP/IP, DHCP Safety & Emission CE Ports One 10/100/1000M Auto-Negotiation LAN RJ45 port Antennas Omni Directional antenna with 1.59dBi gain(2.4G) and 1.03dBi gain(5GB1)1.43dBi gain(5GB4) Wireless Frequency Band Working Temperature 0℃~40℃ (32℉~104℉) Working Humidity 10% ~ 90% RH, Non-condensing Storage Temperature -40℃~70℃(-40℉~158℉) Storage Humidity 5% ~ 95% RH, Non-condensing ● 802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. ● 802.11g - specification for wireless networking at 54 Mbps using directsequence spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security. ● 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) was formed to help accelerate the IEEE 802.11n development process and promote a technology specification for 2.4GHz：2.4~2.4835GHz 5GHz：5.15~5.25GHz, 5.725~5.85GHz 2.4GHz： 11n：up to 600Mbps 11g：54/48/36/24/18/12/9/6Mbps Radio Data Rate WEP, WPA-PSK, WPA2-PSK 11b：11/5.5/2/1Mbps 5GHz： 11ac: up to 1300Mbps 11a: 54/48/36/24/18/12/9/6Mbps Appendix interoperability of next-generation wireless local area networking (WLAN) products. ● ● Access Point (Range Extender) - A wireless LAN transceiver or "base station" that can connect a wired LAN to one or many wireless devices. Access points can also bridge to each other. DNS (Domain Name System) – An Internet Service that translates the names of websites into IP addresses. ● Domain Name - A descriptive name for an address or group of addresses on the Internet. ● DoS (Denial of Service) - A hacker attack designed to prevent your computer or network from operating or communicating. ● DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over existing traditional phone lines. ● ISP (Internet Service Provider) - A company that provides access to the Internet. ● MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be transmitted. ● SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. ● WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. ● ● WLAN (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area. ● WPA (Wi-Fi Protected Access) - WPA is a security technology for wireless networks that improves on the authentication and encryption features of WEP (Wired Equivalent Privacy). In fact, WPA was developed by the networking industry in response to the shortcomings of WEP. One of the key technologies behind WPA is the Temporal Key Integrity Protocol (TKIP). TKIP addresses the encryption weaknesses of WEP. Another key component of WPA is built-in authentication that WEP does not offer. With this feature, WPA provides roughly comparable security to VPN tunneling with WEP, with the benefit of easier administration and use. This is similar to 802.1x support and requires a RADIUS server in order to implement. The Wi-Fi Alliance will call this, WPA-Enterprise. One variation of WPA is called WPA Pre Shared Key or WPA-Personal for short - this provides an authentication alternative to an expensive RADIUS server. WPA-Personal is a simplified but still powerful form of WPA most suitable for home Wi-Fi networking. To use WPA-Personal, a person sets a static key or "passphrase" as with WEP. But, using TKIP, WPA-Personal automatically changes the keys at a preset time interval, making it much more difficult for hackers to find and exploit them. The Wi-Fi Alliance will call this, WPAPersonal. Wi-Fi –A trademark of the Wi-Fi Alliance and the brand name for products using the IEEE 802.11 family of standards. Appendix
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Warning : Root object (1 0 obj) not found at 17EXIF Metadata provided by EXIF.tools