TRAFICON N V 10-6034-6035 TrafiCam Wireless US User Manual Man TrafiCam R600 4TI R401 Installation EN

TRAFICON N.V. TrafiCam Wireless US Man TrafiCam R600 4TI R401 Installation EN

Contents

revised users manual

XInstallation manualProduct reference number TrafiCam®: 10-6034 - Revision R6.014TI: 10-6027 - Revision R4.01TrafiCam® with a 4TI interfaceDraft document, not released - September 2007
iWXTrafiCam® with a 4TI interfaceSafety warningEN55022FCC Part 15WarningThis is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment under FCC rules. FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 4,89 cm (1,93 inches) between the radiator and your body.
iiWXTrafiCam® with a 4TI interfaceNoticeThe information contained in this document is subject to change without notice.Traficon® n.v. makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.Traficon® n.v. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.No part of this document may be copied, reproduced, or translated to another language without the prior written consent of Traficon® n.v.© Copyright 2007, Traficon® n.v. - All rights reservedTraficon® n.v.Vlamingstraat 19B-8560 WevelgemBelgiumTel +32 (0)56 37.22.00Fax +32 (0)56 37.21.96E-mail traficon@traficon.com
iiiWXTrafiCam® with a 4TI interfaceTable of contentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2The TrafiCam® system items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2The TrafiCam® sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4The 4TI interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6The cables for connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8The accessories for mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Hardware specification - TrafiCam® sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Hardware specification - 4TI interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Specification - wireless communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ivWXTrafiCam® with a 4TI interfaceList of figuresFigure 1: TrafiCam® installed at an intersection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Figure 2: Items of the TrafiCam® system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Figure 3: Architecture of the TrafiCam® system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Figure 4: Front and side view of the TrafiCam® sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Figure 5: The TrafiCam® sensor opened . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Figure 6: The 4TI interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Figure 7: The cables for connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Figure 8: The mounting accessories (brackets and tube) . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1WXTrafiCam® with a 4TI interface1. IntroductionThis manual describes the hardware and installation of a wireless TrafiCam® system with the 4TI as the interface between the TrafiCam® sensor, PC and traffic controller. Functional characteristics of TrafiCam®• Presence detection at the stop bar on intersections • Advance detection of vehicles approaching the intersectionon up to 8 zones over different lanes. The user can make these zones direction sensitive.Via its digital outputs, TrafiCam® provides an input to the traffic controller upon presence detection. Functional characteristics of 4TI• Serves as the interface for up to 4 TrafiCam® sensors• Provides up to 16 outputs (maximum 4 per TrafiCam®) to the traffic controllerFigure 1: TrafiCam® installed at an intersectionThe user configures TrafiCam® and the 4TI via TrafiCam® PC Tool. This tool allows to:For TrafiCam®• place the presence detection zones on an image from TrafiCam®• assign the hardware outputs to the presence zones• activate and verify the configurationFor 4TI• link the outputs of TrafiCam® sensors and 4TI• activate the system configuration
2WXTrafiCam® with a 4TI interface2. Hardware2.1. The TrafiCam® system itemsThe TrafiCam® system has the following items.Figure 2: Items of the TrafiCam® system1 = The TrafiCam® sensor2 = The mounting accessories3 = The installation CD (with the PC Tool and the manuals)4 = Tools (hex keys and cable tags)5 = The 4TI interfaceIn addition, the installation requires:* retaining straps* connection cables (see The cables for connection)* PSU (12-26 V AC/DC)Note: Traficon does not supply the retaining straps or the PSU.15234
3WXTrafiCam® with a 4TI interfaceThe scheme below illustrates the architecture of the system.Figure 3: Architecture of the TrafiCam® system
4WXTrafiCam® with a 4TI interface2.2. The TrafiCam® sensorFigure 4: Front and side view of the TrafiCam® sensorA = The lensB = The gland to insert the cable for connection between sensor and interfaceC = The LED (will light upon presence detection)D = The screws on the rear shell (to open the sensor)E = The rotating point to fix the mounting bracket A CDE B
5WXTrafiCam® with a 4TI interfaceFigure 5: The TrafiCam® sensor openedCN1 = The connector to the 4TICN1 pinout: see below.A = The fixation plate (to keep the connection cable in place)B = The product labelC = Flattened side of the rear shell (as an aid to close the sensor)Pinout of connector CN1Pin Description+ + Power supply- - Power supply GroundingA RS-485AB RS-485BCN1ACB
6WXTrafiCam® with a 4TI interface2.3. The 4TI interfaceFigure 6: The 4TI interfaceA The USB/B connector (to connect to the PC)JP12 The groundingJ11 The PSU connector for power supply to the 4TI interface4TI can also feed the TrafiCam® sensors. J1, J3, J4 or J5The connector to the TrafiCam® master sensor J12, J13 The output connectors to the traffic controllerThe tables below provide the pinout scheme of connector J1 to J5, J12 and J13.JP12AJ11J5J4J3J1J12J13
7WXTrafiCam® with a 4TI interfacePinout of connector J1(same for connector J3, J4, J5)Pin Description+ + Power supply- - Power supplyA RS-485AB RS-485B GroundingPinout of connector J12 and J13 Pin DescriptionError - - Error output Error + + Error output Common Common output(for output 1 to 16)Output 1 to 16 Output 1 to 16
8WXTrafiCam® with a 4TI interface2.4. The cables for connectionThe table below gives an overview of the cables used for connecting the TrafiCam® sensor, the 4TI interface and the PC.Figure 7: The cables for connectionConnection Cable IllustrationSensor to interface Shielded twisted pair cable, UV-resistant, 4 wires + shieldingSTP, d. 5-10 mm, min 2x2 + shieldInterface to PC USB cable type USB/A - USB/B
9WXTrafiCam® with a 4TI interface2.5. The accessories for mountingThere is a mounting bracket for the TrafiCam® sensor and a mounting bracket to the pole. The tube connects both brackets.Figure 8: The mounting accessories (brackets and tube)A = The mounting bracket for the TrafiCam® sensorB = The tubeC = The mounting bracket to the poleD = The holes to put the retaining straps throughCABD
10WXTrafiCam® with a 4TI interface3. InstallationDo not remove the lens cover until the TrafiCam® is installed.Ensure that the system power is off before starting the installation..Step I: Mount the TrafiCam® on a stable pole.1. Fix the mounting tube to the brackets (Torque max = 1,3 Nm).2. Fix the TrafiCam® to the pole using retaining straps.Put the retaining straps through the holes in the bracket.3. Position the TrafiCam® provisionally (Torque max = 1,3 Nm).You can mount the TrafiCam® in a horizontal or vertical position.TrafiCam® is a downward looking device.Verify that there is no horizon in the image!
11WXTrafiCam® with a 4TI interfaceStep IIa: Connect the TrafiCam® master sensor to the 4TI interface.Use a shielded twisted pair cable, UV-resistant, 4 wires+shield.At the Traficam® side1. Open the sensor.2. Loosen the cable gland.3. Insert the cable into TrafiCam® through the gland.4. Strip the wires and fix the cable tags. Isolate the grounding wire.5. connect the cable to CN1 and fix the cable plate.6. Close the TrafiCam® (Torque max = 1,0 Nm).7. Tighten the cable gland.At the 4TI interface side8. Connect the cable to the connector J1 (or J3, J4, J5).Step IIb: Connect the TrafiCam® slave sensors to the local power supply.Use a shielded twisted pair cable, UV-resistant, 2 wires +grounding.At the Traficam® side1. Open the sensor.2. Loosen the cable gland.3. Insert the cable into TrafiCam® through the gland.4. Strip the wires and fix the cable tags. Isolate the grounding wire.5. connect the cable to CN1 (power supply and grounding pins only) and fix the cable plate.6. Close the TrafiCam® (Torque max = 1,0 Nm).7. Tighten the cable gland.At the 4TI interface sideNo connectionsNote: If you wish to supply power to the slave sensors via the 4TI interface you should connect only the pins of CN1 as described above. Do NOT connect the RS-485 wires.
12WXTrafiCam® with a 4TI interfaceStep III: Mount the 4TI interface by clicking it on the DIN rail.Step IV: Connect the interface to the traffic controller.
13WXTrafiCam® with a 4TI interfaceFinally connect the power supply.The configuration manual (separate manual) describes how to optimise the position of the TrafiCam®. Tighten all screws after optimising the position of the TrafiCam®.Step V: Connect the interface to the PC.Use a USB cable type USB/A - USB/B.
14WXTrafiCam® with a 4TI interface4. MaintenanceThe maintenance of the TrafiCam® can be done during the regular maintenance of the traffic lights and controller. Note: Depending on the on-site conditions, you may need to increase the frequency of maintenance.Instruction Frequency Tools RemarkClean the faceplate of the TrafiCam®.Check the camera image.Verify the configuration of the system.Once per yearOnce per yearSoft cloth and mild detergentPC with TrafiCam® PC toolAvoid movement of the TrafiCam®.Use the configuration manual for guidance.
15WXTrafiCam® with a 4TI interface5. Hardware specification - TrafiCam® sensorCAMERACMOS, black&white, resolution 640x480, 1/3 “DIMENSIONSL x H x W: 45 cm x 16 cm x 10 cm mounted vertically41 cm x 18 cm x 10 cm mounted horizontallyMass (including mounting bracket, excluding cable): 600 gSensor diameter: 10 cmMATERIALSSensor Front and back shell: polycarbonateMid section: fibre reinforced polyamide Mounting bracket: fibre reinforced polyamide Tube: aluminiumCOMMUNICATIONRS485 service port for configurationOUTPUTS4 optically isolated digital outputs, Imax = 50 mA, Pmax = 300 mWPOWER SUPPLY VOLTAGE INPUT+20V ...+26V AC/DCPOWER CONSUMPTION85 mA @ +12 V DC (1,2 W)50 mA @ +24 V DC (1,2 W)ENVIRONMENTALTemperature range: between - 34°C and +80°C0 to 95 % relative humidity, non-condensingHousing: waterproof to IP67 Materials: weatherproof, UV-resistant REGULATORYEMC: CE Directive 89/336/EEC; product standard EN 55022 Class AFCC: FCC part 15 Class ANEMA: NEMA II Shock and vibration LENS TYPE > Wide angle Narrow angleFocal distance 3,0 mm 8,0 mmField of view - horizontal 95° 32°Field of view - vertical 65° 22°Field of view - diagonal 103° 39°
16WXTrafiCam® with a 4TI interface6. Hardware specification - 4TI interfaceDIMENSIONSL x H x W: 18,5 cm x 8,5 cm x 5 cm; DIN-rail clickableMass: 250 gCOMMUNICATIONUSB between 4TI and PCRS-485 between 4TI and TrafiCam®OUTPUTS16 optically isolated digital outputs1 optically isolated digital error outputPOWER SUPPLY VOLTAGE INPUT+12V ...+26V AC / DCPOWER CONSUMPTION120 mA @ +12 V DC (1,5 W)60 mA @ +24 V DC (1,5 W)ENVIRONMENTALTemperature range: between - 34°C and +80°CREGULATORYEMC: CE Directive 89/336/EEC; product standard EN 55022 Class AFCC: FCC part 15 Class ANEMA: NEMA II Shock and vibration
17WXTrafiCam® with a 4TI interface7. Specification - wireless communicationWireless 915MHz Frequency Band (USA, Mexico, …)Technology: Frequency Hopping Spread Spectrum (FHSS)Frequency Range: 902-928MHzAvailable Hop Patterns: 6Transmission power (ERP): 250mWMax. communications distance: max. 400m* with omni-directional antenna (to be confirmed)Effective bandwidth: 115,2kbaud netto*Input Voltage: 20-26V AC/DCCurrent Consumption: 85mA @ 24V Power Consumption: Peak 2,0W (to be confirmed), Average 1,5W (to be confirmed)Certification: FCC chapter 47 part 15 .207/209/249FCC equipment autorisation: pendingFCC ID: VE7-10-6034-6035* In ideal conditions: direct line of sight, no fixed objects in ellipse (trees/leafs, power lines, buildings, etc..), no moving objects in ellipse (buses, trucks, trams, etc..), good weather, normal traffic environment, no interference, 25mW transmission power, higher than 6m above the ground's surface
TrafiCam® with a 4TI interface18WXIndexCConnector pinout4TI connector J1 (J3, J4, J5) 74TI connector J12 (J13) 7TrafiCam connector CN1 5HHardware specification4TI interface 16TrafiCam sensor 15IInstallation accessoriescables for connection 8mounting brackets and tube 9Installation, stepwise 10MMaintenance 14SSpecification wireless communication 17System TrafiCam - 4TIarchitecture 3Items 2TTrafiCam sensorfront and side view 4opened 5

Navigation menu