TRANE Air Conditioner/heat Pump(outside Unit) Manual L0905062

User Manual: TRANE TRANE Air conditioner/heat pump(outside unit) Manual TRANE Air conditioner/heat pump(outside unit) Owner's Manual, TRANE Air conditioner/heat pump(outside unit) installation guides

Open the PDF directly: View PDF .
Page Count: 8

18=AC51D6=1

iiI!;!l!ii !I! ii iI:i

Condensing Units

4TTR4A/B Models

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

IMPORTANT -- This Document is customer property and is to remain with this unit. Please return to service information

pack upon completion of work.

These instructions do not cover all variations in

systems nor provide for every possible contingency to

be met in connection with installation. All phases of

this installation must comply with NATIONAL, STATE

AND LOCAL CODES. Should further information be

desired or should particular problems arise which are not

covered sufiieiently for the purchaser's purposes, the matter

should be referred to your installing dealer or local distributor.

A. GENERAL

This information is intended for use by individuals posses-

sing adequate backgrounds of electrical and mechanical

experience. Any attempt to repair a central air conditioning

product may result in personal injury and or property

damage. The manufacturer or seller cannot be responsible

for the interpretation of this information, nor can it assume

any liability in connection with its use.

The following instructions cover 4TFR4 Condensing Units.

NOTE:

These outdoor units are designed to be installed with

approved/matched Trane indoor systems.

These units use R-410A refrigerant which operates at 50 to

70% higher pressures than R-22. Use only R-410A approved

service equipment. Refrigerant cylinders are painted a

"Rose" color to indicate the type of refrigerant and may

contain a "dip" tube to allow for charging of liquid refriger-

ant into the system. All R-410A systems use a POE oil that

readily absorbs moisture from the atmosphere. To limit this

"hygroscopic" action, the system should remain sealed

whenever possible. Never break a vacuum with air and

always change the driers when opening the system for

component replacement.

Check for transportation damage after unit is uncrated.

Report promptly, to the carrier, any damage found to the unit.

To determine the electrical power requirements of the unit,

refer to the nameplate of the unit. The electrical power

available must agree with that listed on the nameplate.

UNiT CONTAINS R-410A REFRIGERANT!

R-410A OPERATING PRESSURE EXCEEDS THE

LIMIT OF R-22. PROPER SERVICE EQUIPMENT IS

REQUIRED. FAILURE TO USE PROPER SERVICE

TOOLS MAY RESULT IN EQUIPMENT DAMAGE OR

PERSONAL INJURY.

SERVICE

USE ONLY R-410A REFRIGERANT AND

APPROVED POE COMPRESSOR OIL.

B. LOCATION AND PREPARATION

OF THE UNiT

1. When removing unit from the pallet, notice the tabs on

the basepan. Remove tabs by cutting with a sharp tool as

shown in Figure 2 (see page 2).

2. The unit should be set on a level support pad at least as

large as the unit base pan, such as a concrete slab. If this

is not the application used please refer to application

bulletin "Trane XR-APG**-EN". (*denotes latest

revision number)

|nstaI|er's Guide

@BASEPAN TAB REMOVAL NOTE:

Attach R-410A CAUTION Label (located in documentation

package) to access panel of indoor section.

IMPORTANT:

The outdoor unit is shipped withthe proper size orifice and a

stick-on orifice size label in an envelope attached to the outdoor

unit. Outdoor unit nameplate will have correct orifice size

specified as BA YFCCV---A for rated pefformance.

D. iNSTALLiNG REFRIGERANT LINES

3. The support pad must NOT be in direct contact with any

structure. Unit must be positioned a minimum of 12"

from any wall or surrounding shrubbery to insure

adequate airflow. Clearance must be provided in ff'ont of

control box (access panels) & any other side requiring

service access to meet National Electrical Code. Also,

the unit location must be fhr enough away from any

structure to prevent excess roof run-off water from

pouring directly on the unit. Do not locate unit(s) close

to bedroom(s).

4. The top discharge area must be unrestricted fbr at least

five (5) feet above the unit.

5. When the outdoor unit is mounted on a roof! be sure the

roof will support the unit's weight. Properly selected

isolation is recommended to prevent sound or vibration

transmission to the building structure.

6. The maximum length of refrigerant lines ff'om outdoor to

indoor unit should NOT exceed sixty (60) feet.

7. If outdoor unit is mounted above the air handler, maxi-

mum lift should not exceed sixty (60) feet (suction line).

If air handler is mounted above condensing unit, maxi-

mmn lift should not exceed sixty (60) feet (liquid line).

NOTE:

Refer to "Refrigerant Piping Software" Pub. No. 32-3312-02.

8. Locate and install indoor coil or air handler in accor-

dance with instruction included with that unit.

C. ACCUTRON TM FLOW CONTROL VALVE

If the indoor unit System Refrigerant Flow control is an

Aecutron TM orifice and check valve assembly, an orifice size

change may be necessary.

The outdoor model determines the required orifice size.

Check the listed orifice size on nameplate of the selected

outdoor model. If the indoor unit is fhctory shipped with a

diffbrent orifice size, the orifice must be changed to obtain

system rated perfbrmance.

BRAZE TYPE iNDOOR END

SEALING CAP

If using existing refrigerant lines make certain that all joints

are brazed, not soldered.

Condensing units have provisions for braze connections.

Pressure taps are provided on the service valves of outdoor

unit fbr compressor suction and liquid pressures.

The indoor end of the recommended refrigerant line sets may

be straight or with a 90 degree bend, depending upon situa-

tion requirements. This should be thoroughly checked out

befbre ordering refrigerant line sets.

The gas line must always be insulated.

in scroll compressor applications, dome temperatures may

be hot. Do not touch top of compressor, may cause minor

to severe burning.

The units are fhctory charged with the system charge

required when using fifteen (15) feet of connecting line. Unit

nameplate charge is the same.

Final refrigerant charge adjustment is necessary. Use

the Charging Charts in the outdoor unit Service Facts.

1. Determine the most practical way to run the lines.

2. Consider types of bends to be made and space limitations.

NOTE:

Large diameter tubing will be very difficult to rebend once it

has been shaped.

3. Determine the best starting point for routing the refriger-

ant tubing -- INSIDE OR OUTSIDE THE STRUCTURE.

4. Provide a pull-thru hole of sufficient size to allow both

liquid and gas lines.

5. Be sure the tubing is of sufficient length.

6. Uncoil the tubing -- do not kink or dent.

7. Route the tubing making all required bends and properly

secure the tubing betbre making connections.

8. To prevent a noise within the building structure due to

vibration transmission from the reff'igerant lines, the

tbllowing precautions should be taken:

a. When the refrigerant lines have to be thstened to floor

joists or other ff'aming in a structure, use isolation

type hangers.

b. Isolation hangers should also be used when reff'iger-

ant lines are run in stud spaces or enclosed ceilings.

c. Where the reff'igerant lines run through a wall or sill,

they should be insulated and isolated.

d. Isolate the lines from all ductwork.

|nsta||er's Guide

©LiQUiD LiNE SERVICE VALVE

ROLLED EDGE TO

KF'_.._/ / CAPTIVATESTEM

CAP

sE.%"Ic"s,DEoF .EXRE%%

SERVICE _ k_,Y /

PORT -- /

LIQUID LINE

CONNECTION

E. SERVICE VALVE OPERATION

BRASS LIQUID LINE SERVICE VALVE

The Brass Liquid Line Service Valve is thetory shipped in the

seated position to hold thctory charge. The pressure tap

service port (when depressed) opens only to the field brazing

side of the valve when the valve is in the seated position.

The liquid line valve is not a back seating valve (see

WARNING below).

LEAK CHECK

iMPORTANT:

Replace pressure tap port valve core before attaching hoses

for evacuation.

After the brazing operation of refrigerant lines to both the

outdoor and indoor unit is completed, the field brazed

connections must be checked for leaks. Pressurize through

the service valve ports, the indoor unit and field refrigerant

lines with dry nitrogen to 350-400 psi. Use soap bubbles or

other leak-checking methods to see that all field joints are

leak-fi'ee! If not, release pressure; then repair!

SYSTEM EVACUATION

NOTE:

Since the outdoor unit has arefrigerant charge, the gas and

liquid line valves must remain closed.

1. Upon completion of leak check, evacuate the refrigerant

lines and indoor coil before opening the gas and liquid

line valves.

2. Attach appropriate hoses from manifold gauge to gas

and liquid line pressure taps.

Extreme caution should be exercised when opening the

Liquid Line Service Valve. Turn valve stem counterclock-

wise only until the stem contacts the rolled edge. (See

Figure 4) No torque is required.

BRASS GAS LINE SERVICE VALVE

The Brass Gas Line Service Valve is shipped in the closed

position to hold the rectory refrigerant charge. The pressure

tap service port (when depressed) opens only to the field

brazing side when the valve is in the closed position. The Gas

Line Service Valve is full open with a 1/4 turn. See Figure 5.

BRAZING REFRIGERANT LINES

1. Remove lower access cover to access service valves.

2. Before brazing, remove plugs from external copper stub

tubes. Clean internal and external surIhces of stub

tubes prior to brazing.

3. Cut and fit tubing, minimizing the use of sharp

90 ° bends.

4. Insulate the entire gas line and its fittings.

5. Do NOT allow uninsulated liquid line to come in direct

contact with bare gas line.

6. Precautions should be taken to avoid heat damage

to the pressure tap valve core during brazing. It is

recommended that the pressure tap port valve

core be removed and a wet rag wrapped around

the valve body.

NOTICE:

Use care to make sure that no moisture enters pressure tap

port, while wet rag is being used.

NOTICE:

Precautions should be taken to avoid heat damage to

basepan during brazing. It is recommended to keep the

flame directly off of the baeepan.

7. Use a Dry Nitrogen Puige and Brazing Alloy without flux

when brazing the field line to the copper thctory connec-

tion. Flow dry nitrogen into either valve pressure tap

port, thru the tubing and out the other port while brazing.

8. Braze using accepted good brazing techniques.

NOTE:

Unnecessary switching of hoses can be avoided and

complete evacuation of all lines leading to sealed system

can be accomplished with manifold center hose and

connecting branch hose to a cylinder of R-410A and

vacuum pump.

3. Attach center hose of manifold gauges to vacuum pump.

4. Evacuate until the micron gauge reads no higher than

350 microns.

5. Close offvalve to vacuum pump and observe the micron

gauge. If gauge pressure rises above 500 microns in one (1)

minute, then evacuation is incomplete or system has a leak.

6. If vacuum gauge does not rise above 500 microns in

one (1) minute, the evacuation should be complete.

7. With vacuum pump and micron gauge blanked off, open

valve on R-410A cylinder and charge refrigerant lines and

indoor coil with vapor to tank pressure of R-410A supply.

NOTE:

DO NOT VENT REFRIGERANT INTO THE ATMOSPHERE.

8. Close valve on R-410A supply cylinder. Close valves on

manifold gauge set and remove refioigerant charging

hoses from liquid and gas pressure tap ports.

@GAS LiNE SERVICE VALVE

c,P_ ,%,%,27L,_.....

FOR FULL OPEN

UN,TS,OE/!_ TM

oP VALVE

PRESSURE TAP PORT /#

GAS LINE CONNECTION

18-AC51 D6-1

|nsta||er's Guide

NOTE:

A 3/16" Allen wrench is required to open liquid line service

valve. A I/4" Open End or Adjustable wrench is required to

open gas line valve. A 3/4" Open End wrench is required to

take off the valve stem cap.

9. The liquid line shut-offvalve can now be opened. Remove

shut-off valve cap. Fully insert hex wrench into the stem

and backout counterclockwise until valve stem just touches

rolled edge (approximately five [5] turns) observing

WARNING statement on page 3. See Figure 4.

10. Replace liquid service pressure tap port cap and valve

stem cap. These caps MUST BE REPLACED to

prevent leaks. Replace valve stein cap and pressure tap

cap finger tight, then tighten an additional 1/6 turn.

11. The gas valve can now be opened. Open the gas valve by

removing the shut-off valve cap and turning the valve

stem 1/4 turn eounterelockwise, using 1/4" Open End or

Adjustable wrench. See Figure 5.

12. The gas valve is now open for refl'igerant flow. Replace

valve stem cap to prevent leaks. Again, these caps

MUST BE REPLACED to prevent leaks. Replace valve

stem cap and pressure tap cap finger tight, then tighten

an additional 1/6 turn. See Figure 5.

If refl'igerant lines are longer than 15 feet and!or a

diff>rent size than recommended, it will be necessary to

adjust system refl'igerant charge upon completion of

installation. See unit Service Facts.

F. ELECTRICAL CONNECTIONS

When installing or servicing this equipment, ALWAYS

exercise basic safety precautions to avoid the possibility of

electric shock.

1. Power wiring and _'ounding of equipment must comply

with local codes.

2. Power supply must agree with equipment nameplate.

3. Install a separate disconnect switch at the outdoor unit.

4. Ground the outdoor unit per local code requirements.

5. Provide flexible electrical conduit whenever vibration

transmission may create a noise problem within the

structure.

6. The use of color coded low voltage wire is recommended

to simplify connections between the outdoor unit, the

thermostat and the indoor unit.

Table I-- NEC Class II Control Wiring

24 VOLTS

WIRE SIZE MAX. WIRE LENGTH

18 AWG 150 FT

16 AWG 225 FT.

14 AWG 300 FT.

7. Table 1 defines maximum tota! length of low voltage

wiring from outdoor unit, to indoor unit, and to thermostat.

8. Mount the indoor thermostat in accordance with instruc-

tion included with the thermostat. Wire per appropriate

hook-up diagram (included in these instructions).

G. COMPRESSOR START UP

After all electrical wiring is complete, SET THE THERMO-

STAT SYSTEM SWITCH IN THE OFF POSITION SO

COMPRESSOR WILL NOT RUN, and apply power by

closing the system main disconnect switch. This will activate

the compressor sump heat (where used). Do not change the

Thermostat System Switch until power has been applied for

one (1) hour. Following this procedure will prevent potential

compressor overload trip at the initial start-up.

H. OPERATIONAL AND

CHECKOUT PROCEDURES

Final phases of' this installation are the unit Operational and

Checkout Procedures which are found in this instruction (see

page 8). To obtain proper performance, all units must be

operated and charge adjustments made in accordance with

procedures found in the Service Facts.

I. ELECTRIC HEATERS

Electric heaters, if used, are to be installed in the air han-

dling device according to the instructions accompanying the

air handler and the heaters.

d. START CONTROL

Some models have quick start components which are fhctory

installed. For models that do not have fhctory installed start

components, provisions are made for a field installed start kit

accessory. When adding an accessory, follow the instructions

provided with the kit.

K. OUTDOOR THERMOSTAT

An outdoor thermostat TAYSTAT250B may be field installed.

For data, see wiring diagram attached to unit and instruction

sheet packaged with outdoor thermostat.

L. SEACOAST SHIELD

Units installed within one mile of salt water, including

seacoasts and inland waterways, require the addition of

BAYSEAC001 (Seacoast Kit) at the time of installation.

IMPORTANT:

See Limited Warranty information in Use and Care Manual

M. TROUBLESHOOTING

TROUBLESHOOTING CHART -- WHAT TO CHECK

SYSTEMFAULTS

REFRIGERANTCIRCUIT

ELECTRICAL

Compressor&OD FanDoNotStart

CompressorWillNotStartButOD FanRuns

OD FanWon'tStart

CompressorNt_msButWon'tStart

CompressorCyclesonIOL

ID BlowerWon'tStart

PPrimaryCauses S Sec0ndaryCauses

4 18-AC51 D6-1

|nsta||er's Guide

TYPICAL FIELD HOOK=UP DIAGRAMS

T'STAT IR HANDLER

...... R

...... Wl

A I CONDITIONER

...... y

ODT

_ ...... B

VARIABLE SPEED

T'STAT AIR HANDLER AIR CONDITIONER

F_q

FTq

1233

ISTq

_"= === y

0DT A

JoP_,O...... o_ i

'"B

PRINTEDFROM B152901P02 PRINTED FROMBI52gosP03

÷ CONNECTIONSTO BE MADE FOR OPERATION OF

BLOWERWITH HUMIDISTAT IN COOLING

T 'STAT

NOTE

I -STAGE

2-STAGE

FURNACE

Fcl

AI CONDITIONER

_. ..... y

...... B

PRINTEDFROMB152903P02

-kW2 present only on 2 stage

thermostat and furnace

Notes:

1. Be sure power supply agrees with equipment nameplate.

2. Power wiring and grounding of equipment must comply with local codes.

3. Low voltage wiring to be No. 18 AWG minimum conductor.

4. ODT-B must be set lower than ODT-A.

5. If outdoor thermostats (ODT) are not used, connect W1 to W2 and W3.

T 'STAT

] NOTE

PRI NTE

VARIABLE SPEED

2 STAGE FURNACE

i-tS]]

Frl

[]

prl

FRO BI52901P04

LEGEND

..... FACTORY WIRING

_ FIELD WIRING

AI CONDITIONER

_-.-y

18-AC51 D6-1 5

|nstaller's Guide

4TTR4 OUTLINE DRAWING

NOTE: ALL DIMENSIONSARE IN MM (INCHES).

SERVICE PANEL....................

ELECTRICAL AND REFRIGERANT

COMPONENTCLEARANCES

PER PREVAILING CODES

TOP DISCHARGE AREA SHOULD BE

UNRESTRICTED FOR AT LEAST 1524 {5 FEET)

ABOVE UNIT UNIT SHOULDBE PLACED SO ROOF

RUN OFF WATER DOEB NOT POUR DIRECTLY ON UNIT,

AND SHOULDBE AT LEAST 305 {IR"/ FROM WALL AND

ALL SURROUNDINGSHRUBBERYON TWOSIDES

OTHER TWOSIDES UNRESTRICTED

ELECTRICAL SERVICE -_

PANEL

222 (7/8) DIA

LOWVOLTAGE

286 (I I/8) DIA KO

222 (7/8) DIA HOLE IN CONTROL

BOX BOTTOMFOR ELECTRICAL

POWERSUPPLY

LIOUID LINE SERVICE VALVE

IIEII ID FEMALE BRAZE

CONNECTIONWITH I/4 II SAE

FLARE PRESSURETAP FITTINGS

IbI' _ ,

//./I \ _ k_\

FIG.1

FOR ALTERNATE

_} ELECTRICAL ROUTING

AS LINE I/4 TURN BALL SERVICE VALVE, "D"

ID FEMALE BRAZED CONNECTION WITH I/4" SAE

FLARE PRESSURE TAP FITTING

MODELS

4TTR4018B

4TTR4024B

4TTR4030A

4TTR4036A

4TTR4042A

4TTR4048A

4TTR4060B

BASE

FIG.

832 (32-3/4)

933 (36-3/4)

943 (37-1/8)

1045 (41-1/8)

829 (32-5/8)

946 (37-1/4)

C D E F G H J K

756 (29-3/4) 1/2 1/4 143 (5-5/8) 92 (3-5/8) 210 (8-1/4) 79 (3-1/8) 508 (20)

756 (29-3/4) 5/8 5/16 143 (5-5/8) 92 (3-5/8) 210 (8-1/4) 79 (3-1/8) 508 (20)

756 (29-3/4) 3/4 5/16 143 (5-5/8) 92 (3-5/8) 210 (8-1/4) 79 (3-1/8) 508 (20)

756 (29-3/4) 3/4 3/8 143 (5-5/8) 92 (3-5/8) 210 (8-1/4) 79 (3-1/8) 508 (20)

870 (34-1/4) 3/4 3/8 152 (6) 98 (3-7/8) 219 (8-5/8) 86 (3-3/8) 508 (20)

870 (34-1/4) 7/8 3/8 152 (6) 98 (3-7/8) 219 (8-5/8) 86 (3-3/8) 508 (20)

6 18-AC51 D6-1

Insialler's Guide

MOUNTING HOLE LOCATION

NOTE: ALL DIMENSIONS ARE IN MM (INCHES).

294 (11 56)_ 1

Ill (6 14)

DRILL4 PLACES

335 (1319)

(2709)

221 (8,69)

NOTE: For model base size,

see table on page 6.

310 (12 20)_

'99 (23 bS)

' ( 2{i 6 'i )

BASE 4

158 (624)

_I)RILL

f 4 PLACES

717 (2824)

(31 s_8)

From Dwg. D152637 Rev. 1

18-AC51 D6-1 7

|nsta||er's Guide

CHECKOUT PROCEDURE

After installation has been completed, it is recommended that the entire system be checked against the following list:

1. Refrigerant Line, Leak checked .................................. [

2. Suction Lines and Fittings properly insulated ........... [

3. Have all Refi'igerant Lines been secured and

isolated properly? ........................................................ [

4. Have passages through masonry been sealed?

If mortar is used, prevent mortar from coming

into direct contact with copper tubing ........................ [

5. Verify tightness of all electrical connects ................... [

6. Observe outdoor fhn during on cycle for clearance

and smooth operation .................................................. [

7. Indoor coil drain line drains freely. Pour water

into drain pan .............................................................. [

] 8. Supply registers and return _'illes open and

] unobstructed ................................................................ [ ]

9. Return air filter installed ............................................ [ ]

] 10. Thermostat thermometer is accurate. Check

against a reliable thermometer. Adjust per

instructions with thermostat ...................................... [ ]

] 11. Is correct speed tap being used?

] (Indoor blower motor) .................................................. [ ]

12. Operate complete system in each mode to

insure safe operation ................................................... [ ]

CHECKOUT PROCEDURE WiTH MAiN P(

Step

No. TO CHECK

1 SumpHeat

2 IndoorFan Operation

3 CoolingOperation

4 CheckingPerformance

& Charge

5 Heating@

Off

iNDOORTHERMOSTAT

SWITCHSETTING

@ @ FanSwitch

Cool Heat Auto On

X X

)WER DISCONNECTS CLOSED (ON)

COMPONENTOPERATION

indoor Outdoor

Blower Fan

Runs Runs

Compressor @ Comp. Furnace

Runs Sump Heat

Heater Comes On

X X X X

x Ix I x I x x

USE CHARTS ATTACHED TO O.D. UNIT

Informowner on howto operatesystem andwhat to expectof it. At the sametimedeliverOwner'sUseand CareBooklet.

@ Also set thermostat dial to call for cooling or heating as necessary.

@ Check only necessary if heating unit is used for indoor section and wiring has been disturbed during installation of cooling equipment,

@ When applicable.

ARI Standard

210/240 UAC

05/08

1r]MN£

Trane

www.trane.com

Trane has a policy of continuous product and product data improvement and it reserves the right to change

design and specifications without notice.

TRANE Air Conditioner/heat Pump(outside Unit) Manual L0905062

Navigation menu

Versions of this User Manual:

Views

Navigation