TRANE Air Conditioner/heat Pump(outside Unit) Manual L0905065

User Manual: TRANE TRANE Air conditioner/heat pump(outside unit) Manual TRANE Air conditioner/heat pump(outside unit) Owner's Manual, TRANE Air conditioner/heat pump(outside unit) installation guides

Open the PDF directly: View PDF .
Page Count: 8

2TWR2-1N-1B

18-BC51D2-3

Pumps

2TWR1 & 2TWR2

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

IMPORTANT -- This Document is customer property and is to remain with this unit. Please return to service information

pack upon completion of work.

These instructions do not cover all variations in

systems nor provide for every possible contingency to

be met in connection with installation. All phases of

this installation must comply with NATIONAL, STATE

AND LOCAL CODES. Should further information be

desired or should particular problems arise which are not

covered sufficiently for the purchaser's purposes, the matter

should be referred to your installing dealer or local distributor.

A. GENERAL

The following instructions cover 2TWR1 and 2TWR2 Heat

Pump Units.

NOTE:

These outdoor units may be used with indoor units

equipped with Thermostatic Expansion Valve or Accutron rM

Flow Control Check Valve (F.C.C.V.) assembly for refrigerant

flow control only.

Check for transportation damage after unit is uncrated.

Report promptly, to the carrier, any damage found to the unit.

To determine the electrical power requirements of the unit,

refer to the nameplate of the unit. The electrical power

available must agree with that listed on the nameplate.

The Weathertron ®Heat Pump has been designed and

manufactured to withstand and operate in severe winter

conditions. However, there are precautionary steps which

should be taken at the time of installation which -will help

assure the efficient operation of the unit. It is recom-

mended that these precautions be taken for units

being installed in areas where snow accumulation and

prolonged below freezing temperatures occur.

1, Units should be elevated 3 to 12 inches above the pad or

rooftop, depending on local weather. This additional

height will allow better drainage of snow and ice (melted

during defrost cycle) prior to its refreezing. This should

prevent a build-up of ice around the unit which occurs

when unit is not elevated. Insure that drain holes in

unit base pan are not obstructed preventing

draining of defrost water.

2. If possible, avoid locations that are likely to accumulate

snow drifts. If not possible, a snow drift barrier should be

installed around the unit to prevent a build-up of snow

on the sides of the unit and should be of sufficient

distance from the unit to prevent restriction of airflow to

and from the unit. Also allow for proper maintenance

space. The barrier should be constructed of materials

which will blend in with the building design.

5 FT. ABOVE UNIT-UNRESTRICTED

Avoid locating the unit where condensation and freezing

of defrost vapor may annoy the customer. For instance,

installing the unit under a bedroom, ldtchen, or picture

window may be annoying to the customer since conden-

sate and fog will occur during the defrost cycle.

Avoid locating the unit under the eaves or other over-

head structures as sizeable icicles may form and the unit

may be damaged by these falling icicles.

B. LOCATION AND PREPARATION

OFTHE UNIT

1. When removing unit from the pallet, notice the tabs on

the basepan. Remove tabs by cutting with a sharp tool as

shown on page 2, Figure 2, and slide unit off of pallet.

The unit should be set on a level support pad at least as

large as the unit base pan, such as a concrete slab. If this

is not the application used please refer to application

bulletin "Trane APB2001-02".

The support pad must NOT be in direct contact with any

structure. Unit must be positioned a minimum of 12"

from any wall or surrounding shrubbery to insure

adequate airflow. Clearance must be provided in front of

control box (access panels) and any other side requiring

service access to meet National Electrical Code. Also, the

unit location must be far enough away from any struc-

|nsta||er's Guide

@BASEPAN TAB REMOVAL

ture to prevent excess roof run-off water from pouring

directly on the unit. Do not locate unit(s) close to

bedroom(s).

4. The top discharge area must be unrestricted for at least

five (5) feet above the unit.

5. When the outdoor unit is mounted on a roof, be sure the

roof will support the unit's weight. Properly selected

isolation is recommended to prevent transmission to the

building structure.

6. The maximum length of refrigerant lines from outdoor

to indoor unit should NOT exceed sixty (60) feet.

7. If outdoor unit is mounted above the air handler, maxi-

mum lift should not exceed sixty (60) feet (suction line). If

air handler is mounted above condensing unit, maxi-

mum lift should not exceed sixty (60) feet (liquid line).

8. Locate and install indoor coil or air handler in accor-

dance with instruction included with that unit.

C. ACCUTRON TM FLOW CONTROL VALVE

If the indoor unit System Refrigerant Flow control is an

Accutron TM orifice and check valve assembly, an orifice size

change may be necessary.

The outdoor model determines the required orifice size.

Check the listed orifice size on nameplate of the selected

outdoor model. If the indoor unit is factory shipped with a

diffhrent orifice size, the orifice must be changed to obtain

system rated performance.

IMPORTANT'.

The outdoor unit is shipped with the proper size orifice and a

stick-on orifice size label in an envelope attached to the

outdoor unit. Outdoor unit nameplate will have correct orifice

size specified as BAYFCCV --- A for rated performance.

BRAZE TYPE iNDOOR END

SEALING CAP

D. INSTALLING REFRIGERANT LINES

If using existing refrigerant lines make certain that all joints

are brazed, not soldered.

Condensing units have provisions for braze connections.

Pressure taps are provided on the service valves of outdoor

unit for compressor suction and liquid pressures.

The indoor end of the recommended refrigerant line sets may

be straight or with a 90 degree bend, depending upon

situation requirements. This should be thoroughly checked

out before ordering refrigerant line sets.

The gas line must always be insulated.

In scroll compressor applications, dome temperatures may

be hot. Do not touch top of compressor, may cause minor to

severe burning.

The units are factory charged with the system charge re-

quired -when using fifteen (15) f_et of connecting line. Unit

nameplate charge is the same.

Final refrigerant charge adjustment is necessary. Use

the Charging Charts in the outdoor unit Service Facts.

1. Determine the most practical way to run the lines.

2. Consider types of bends to be made and space limitations.

NOTE:

Large diameter tubing will be very difficult to rebend once it

has been shaped.

Determine the best starting point for routing the refriger-

ant tubing - -INSIDE OR OUTSIDE THE STRUCTURE.

Provide a pull-thru hole of sufficient size to allow both

liquid and gas lines.

Be sure the tubing is of sufficient length.

Uncoil the tubing --- do not kink or dent.

Route the tubing making all required bends and properly

secure the tubing before making connections.

To prevent a noise within the building structure due to

vibration transmission from the refrigerant lines, the

following precautions should be taken:

a. When the refrigerant lines have to be fastened to floor

joists or other framing in a structure, use isolation

type hangers.

LiQUiD LiNE SERVICE VALVE

ROLLED EDGE TO

CAP_ @/CAPTIVATE STEM

sEO.ffS ,S'DEOF--- -- .EX.EADgEM

SERVICE _ _ /

PORT -- /

LIQUID LINE

CONNECTION

|nsta||er's Guide

@GAS LiNE BALL SERVICE VALVE

CAP ---__ ,I-J, 1/4 TURN ONLY

COUNTERCLOCKWISE

FOR FULL OPEN

I _ POSITION

VALVEBTEM

UNITSIDE

OFVALVE

PRESSURETAPPORT /

GAS LINE CONNECTION

o,.

CAP _ (_

BODY

COOL

L_ZI i _17_q

CORE

b. Isolation hangers should also be used -when refriger-

ant lines are run in stud spaces or enclosed ceilings.

c. Where the refrigerant lines run through a wall or sill,

they should be insulated and isolated.

d. Isolate the lines from all ductwork.

E. SERVICE VALVE OPERATION

BRASS LIQUID AND GAS LINE SERVICE VALVES

The Brass Liquid and Gas Line Service Valves are factory

shipped in the seated position to hold factory charge. The

pressure tap service port (when depressed) opens only to the

field brazing side of the valve when the valve is in the seated

position. The liquid line valve is not a back seating valve (see

WARNING below).

Extreme caution should be exercised when opening the

Liquid and Gas Line Service Valves. Turn valve stem

counterclockwise only until the stem contacts the roiled

edge. (See Figures 4 and 6) No torque is required.

BRASS GAS LINE BALL SERVICE VALVE

The Brass Gas Line Service Valve is shipped in the closed

position to hold the factory refrigerant charge. The pressure

tap service port (when depressed) opens only to the field

brazing side when the valve is in the closed position.

The Gas Line Service Valve is full open with a 1/4 turn. See

Figure 5.

BRAZING REFRIGERANT LINES

1. Remove lower access cover to access service valves.

2. Before brazing, remove plugs from external copper stub

tubes. Clean internal and external surfaces of stub tubes

prior to brazing.

3. Cut and fit tubing, minimizing the use of sharp 90 ° bends.

4. Insulate the entire gas line and its fittings.

5. Do NOT allow uninsulated liquid line to come in direct

contact with bare gas line.

®GAS LiNE SERVICE VALVE

ROLLED EDGE TO

CAP_ @/CAPTIVATE STEM

UNIT SIDE OF

SERVICE VALVE

HEXHEADED

VALVE SYSTEM

SERVICE-_q

PORT /

GASLINE

CONNECTION

6. Precautions should be taken to avoid heat damage

to the pressure tap valve core during brazing. It is

recommended that the pressure tap port valve

core be removed and a wet rag wrapped around

the valve body.

NOTE:

Use care to make sure that no moisture enters pressure tap

port, while wet rag is being used.

NOTE:

Precautions should be taken to avoid heat damage to

basepan during brazing. It is recommended to keep the

flame directly off of the basepan.

7. Use a Dry Nitrogen Purge and Brazing Alloy without

flux when brazing the field line to the copper thctory

connection. Flow dry nitrogen into either valve pressure

tap port, thru the tubing and out the other port while

brazing.

8. Braze using accepted good brazing techniques.

LEAK CHECK

IMPORTANT:

Replace pressure tap port valve core before attaching hoses for

evacuation.

After the brazing operation of refrigerant lines to both the

outdoor and indoor unit is completed, the field brazed

connections must be checked for leaks. Pressurize through

the service valve ports, the indoor unit and field refrigerant

lines with dry nitrogen to 350-400 psi. Use soap bubbles or

other leak-checking methods to see that all field joints are

leak-free! If not, release pressure; then repair!

SYSTEM EVACUATION

NOTE:

Since the outdoor unit has a refrigerant charge, the gas and

liquid line valves must remain closed.

1. Upon completion of leak check, evacuate the refrigerant

lines and indoor coil before opening the gas and liquid

line valves.

2. Attach appropriate hoses from manifold gauge to gas

and liquid line pressure taps.

NOTE:

Unnecessary switching of hoses can be avoided and corn=

plete evacuation of all lines leading to sealed system can be

accomplished with manifold center hose and connecting

branch hose to a cylinder of HCFC-22 and vacuum pump.

18-BC51 D2-3 3

|nstaI|er's Guide

3. Attach center hose of manifold gauges to vacuum pump.

4. Evacuate until the micron gauge reads no higher than

350 microns.

5. Close offvalve to vacuum pump and observe the micron

gauge. If gauge pressure rises above 500 microns in one

(1) minute, then evacuation is incomplete or system has

a leak.

6. If vacuum gauge does not rise above 500 microns in one

(1) minute, the evacuation should be complete.

7. With vacuum pump and micron gauge blanked off; open

valve on HCFC-22 cylinder and charge refrigerant lines

and indoor coil with vapor to tank pressure of HCFC-22

supply.

NOTE:

DO NOT VENT REFRIGERANT INTO THE ATMOSPHERE.

5. Provide flexible electrical conduit whenever vibration

transmission may create a noise problem within the

structure.

6. The use of color coded low voltage wire is recommended

to simplify connections between the outdoor unit, the

thermostat and the indoor unit.

Table 1--- NEC Class II Control Wiring

24 VOLTS

WIRE SIZE MAX. WIRE LENGTH

18 AWG 150 FT

16 AWG 225 FT.

14 AWG 300 FT.

8. Close valve on HCFC-22 supply cylinder. Close valves on

manifold gauge set and remove refrigerant charging

hoses from liquid and gas pressure tap ports.

NOTE:

A 3/16" Allen wrench is required to open liquid line service

valve. A 1/4" Open End or Adjustable wrench is required to

open gas line valve. A 3/4" Open End wrench is required to

take off the valve stem cap.

9. The liquid line shut-offvalve ean now be opened.

Remove shut-offvalve cap. Fully insert hex wrench into

the stem and backout counterclockwise until valve stem

just touches rolled edge (approximately five [5] turns)

observing WARNING statement on page 3. See Figure 4.

10. Replace liquid service pressure tap port cap and valve

stem eap. These caps MUST BE REPLACED to

prevent leaks. Replace valve stem and pressure tap cap

finger tight, then tighten an additional 1/6 turn.

11. The gas valve can now be opened. For a ball type gas

valve, open the gas valve by removing the shut-offvalve

cap and turning the valve stem 1/4 turn counterclock-

wise, using 1/4" Open End or Adjustable wrench. See

Figure 5. For brass gas line service valve opening, follow

9 and 10 above. See Figure 6.

12. The gas valve is now open for refrigerant flow. Replace

valve stein cap to prevent leaks. Again, these eaps

MUST BE REPLACED to prevent leaks. Replace valve

stem and pressure tap cap finger tight, then tighten an

additional 1/6 turn. See Figure 4.

If refrigerant lines are longer than 15 feet and/or a difi_rent

size than recommended, it will be necessary to adjust system

refrigerant charge upon completion of installation. See unit

Service Facts.

F. ELECTRICAL CONNECTIONS

When installing or servicing this equipment, ALWAYS

exercise basic safety precautions to avoid the possibility

of electric shock.

1. Power -wiring and grounding of equipment must comply

with local codes.

2. Power supply must agree with equipment nameplate.

3. Install a separate disconnect switch at the outdoor unit.

4. Ground the outdoor unit per local code requirements.

Table 1 defines maximum total length of low voltage

wiring from outdoor unit, to indoor unit, and to

thermostat.

Mount the indoor thermostat in accordance with instruc-

tion included -with the thermostat. Wire per appropriate

hook-up diagram (included in these instructions).

G. DEFROST CONTROL

The demand defrost control measures heat pump outdoor

ambient temperature with a sensor located outside the

outdoor coil. A second sensor located on the outdoor coil is

used to measure the coil temperature. The diffhrence be-

tween the ambient and the colder coil temperature is the

diffhrence or delta-T measurement. This delta-T measure-

ment is representative of the operating state and relative

capacity of the heat pump system. By measuring the change

in delta-T, we can determine the need for defrost. The coil

sensor also serves to sense outdoor coil temperature for

termination of the defrost cycle.

FAULT iDENTiFICATiON

A fault condition is indicated by the flashing light on the

defrost control inside the heat pump control box.

In normal operation, the defrost control light will flash once

each second. If the light is flashing more than once per

second or not at all, refer to the service manual for that unit.

PiN iDENTiFiCATiON (See Figure 7.)

1. TEST_COMMON (Shorting any of the other pins to this

pin causes the function of the other pin to be executed.

Leaving this pin open results in the normal mode of

operation.)

2. TST = Test (Shorting TEST_COMMON to this pin

speeds up all defrost board timings.)

©PiN iDENTiFiCATiON

° m

4 18-BC51 D2-3

|nsta||er's Guide

3. FRC_DFT = Forced Defrost (Short TEST_COMMON to

this pin for two (2) seconds to initiate a forced defrost.

Remove the short after defrost initiates.)

DEFROST CONTROL CHECKOUT

Normal operation requires:

a. LED on board flashing 1 time/second.

b. 24V AC between R & B

c. 24V AC between Y & B with unit operating

d. Defrost initiation when FRC_DFT pin is shorted to

TEST_COMMON pin.

If a defrost control problem is suspected, refer to the service

information in control box.

Do NOT connect 24 VAC to T1 (ODS=A) terminal. ODS=A

thermistor WILL BE BLOWN.

I. OPERATIONAL AND CHECKOUT

PROCEDURES

Final phases of this installation are the unit Operational and

Checkout Procedures which are found in this instruction on

page 8. To obtain proper performance, all units must be

operated and charge adjustments made in accordance with

procedures found in the Service Facts.

J. ELECTRIC HEATERS

Electric heaters, if used, are to be installed in the air han-

dling device according to the instructions accompanying the

air handler and the heaters.

K. START CONTROL

Some models have quick start components which are fhctory

installed. For models that do not have factory installed start

components, provisions are made for a field installed start kit

accessory. When adding an accessory, follow the instructions

provided with the kit.

H. COMPRESSOR START UP

After all electrical wiring is complete, SET THE THERMO-

STAT SYSTEM SWITCH IN THE OFF POSITION SO

COMPRESSOR WILL NOT RUN, and apply power by closing

the system main disconnect switch. This will activate the

compressor sump heat (where used). Do not change the

Thermostat System Switch until power has been applied for

one (1) hour. Following this procedure will prevent potential

compressor overload trip at the initial start-up.

L. OUTDOOR THERMOSTAT

An outdoor thermostat TAYSTAT250B may be field installed.

For data, see wiring diagram attached to unit and instruction

sheet packaged with outdoor thermostat.

M. SEACOAST SALT SHIELD

Units installed -within one mile of salt water including

seacoasts and inland waterways, require the addition of

BAYSEAC001 (Seacoast Kit) at the time of installation.

IMPORTANT:

See Limited Warranty information in Use and Care Manual.

TYPICAL FIELD HOOK=UP DIAGRAMS

T'3T/_T

0 _

i ,

i i }

i iB; ;

i i

)iR H,',,I,,DER

_---'i_

(

:ii\

I[...,:_

ii'

L....[_

[ i

> l i, r riD ::<W B5290,>03

Notes:

HF,',,T PU:_4P

@ ,.

L... i

R-n 0

F!K X2 )

_----_,;

: _"--'_!R( T )

1. Be sure power supply agrees with equipment nameplate.

2. Power wiring and grounding of equipment must comply with local codes.

3. Low voltage wiring to be No. 18 AWG minimum conductor.

4. ODT-B must be set lower than ODT-A.

,5. If outdoor thermostats (ODT) are not used, connect W1 to W2 and W3.

6. N/A to programmable thermostat.

'S ;, iAR A,i; SP II)

,::, R HA!',[) ER II[/; i PU_,'I

._,."... y

-- _- --

:iK(X1_)

.... .__c.P._9.'_i ._u4o{_.

-_ B

D- [/01{ 6 D

PR i,i F;;' FROM , i :1;'9 )4PO{Z

LEGEND

..... FACTORY WIRING

FIELD WIRING

18-BC51 D2-3 5

Installer's Guide

SERViCr PANE[ .......... _

IIICIRiCAI ANI) iRIFIRiG_RA_i

COMPONENT C[LARA_C_S

PER PREVAilinG CO_LS

iOP DiSCiiARGE AREA SiiOULD BE

UNRESTRICTED FOR AT LEAST 1524 (5 FEET}

A_OVE UN[_ d_lJ ¸ S_IOU[b BE PEACED SO ROOi

i!_O[[ ¸ WATE[i _O[S NO] _O_R _I_E¢iL¥ ON UNi]

£_i) SHOWi) _i_ A/ JI_ASI¸ 30_ (i_ ¸¸} EROM WA[i ANJ)

ALL SORROUNDiNG SHRUBBERY O_ IWO SinES¸

OTFIER TWO Si_[S U_R_STRiCT[_

FA_EL _ L

25 7 :J

2_ 2 (bS) i_ i011£ .............. .

I O_i ?9 I &( ( . ---

28 f, ', 1_8} DIA K 0 _l H........

22 2 7/8} DIA OlE i_ C,91TR,PL j

BOX tX) I 'C4 [:OH EL E( R ( AL j

/()W_iSIJP[ ' _ .....

(;'U [J _[ S R_iC[ ?/_,'E, -''1''_= ,

@ [: HA [ BE{;} HT I I_

COr_/ECl }01i /i I /,I SA[ F_L

LARE PRESSURE I_P il IGS j ,i il

MODELS BASE FIG. A

2TWR1018A 2 2 651 (25-5/8)

2TWR1024A 2 2 651 (25-5/8)

2TWR1030A 2 2 730 (28-3/4)

2TWR1036A 2 2 730 (28-3/4)

2TWR1042A 3 2 832 (32-3/4)

2TWR1048A 3 2 832 (32-3/4

2TWR1060A 4 1 841 (33-1/8)

2TWR2018A 2 2 651 (25-5/8)

2TWR2024A 2 2 730 (28-3/4)

2TWR2030B 2 2 832 (32-3/4)

2TWR2036A 3 1 832 (32-3/4)

2TWR2042A 3 1 832 (32-3/4)

2TWR2048A 3 1 933 (36-3/4)

2TWR2060A 4 1 1045 (41-1/8)

j;,

FIG. 1

\ KO [OH AiTER_A[E

,, C i IleAl OJ Iq',,

\ GAS i iNE I/4 iWiN SAil SIRVICI VAJVL 'l)'

ID FE_£LE BRAZED CO_N[CTiO_ _IT_ [/4 ¸¸ SA[

FiARE PR[SSbR_ TAP FiTTi_6

724 (28-1/2)

829 (32-5/8)

946 (37-1/4)

724 (28-1/2)

829 (32-5/8)

946 (37-1/4)

651 (25-5/8)

756 (29-3/4)

870 (34-1/4)

651 (25-5/8)

756 (29-3/4)

870 (34-1/4)

I I(/;I) t [! S _,,' '3

V , ' I t4A

BRAZED CO,i!'E,30l

WI I _,1 SAE FLARE

PRESSUR Ts,P f TT_G

GAS Li:/ SIVCE VALVE, x

I D FEI_'ALF BRAZED

¢ON_[¢[I()_ WlTli i/4 '¸ SA[ FLARE

i_R[S$[iR_ lAP i¸ il_ iN6

D E F G H J K

5/8 1/4 127 (5) 57 (2-1/4) 180 (7-1/8) 44 (1-3/4) 457 (18)

3/4 5/16 127 (5) 57 (2-1/4) 180 (7-1/8) 44 (1-3/4) 457 (18)

3/4 5/16 137 (5-3/8) 65 (2-5/8) 210 (8-1/4) 57 (2-1/4) 457 (18)

7/8 3/8 137 (5-3/8) 65 (2-5/8) 210 (8-1/4) 57 (2-1/4) 457 (18)

7/8 3/8 137 (5-3/8) 86 (3-3/8) 210 (8-1/4) 79 (3-1/8) 508 (20)

1-1/8 3/8 137 (5-3/8) 86 (3-3/8) 210 (8-1/4) 79 (3-1/8) 508 (20)

1-1/8 3/8 152 (6) 98 (3-7/8) 219 (8-5/8) 86 (3-3/8) 508 (20)

5/8 1/4 127 (5) 57 (2-1/4) 180 (7-1/8) 44 (1-3/4) 457 (18)

3/4 5/16 137 (5-3/8) 65 (2-5/8) 210 (8-1/4) 57 (2-1/4) 457 (18)

7/8 3/8 143 (5-5/8) 92 (3-5/8) 210 (8-1/4) 79 (3-1/8) 508 (20)

1-1/8 3/8 143 (5-5/8) 92 (3-5/8) 210 (8-1/4) 79 (3-1/8) 508 (20)

1-1/8 3/8 152 (6) 98 (3-7/8) 219 (8-5/8) 86 (3-3/8) 508 (20)

From Dwg. 21D152898 Rev. 9

6 18-BC51 D2-3

|nstal|er's Guide

MOUNTING HOLE LOCATION

Note: All dimensions are in IVllVl(Inches).

BASE 2

BASE 3

NOTE: For model base size,

see table on page 6.

........................................................$99 (255 n_ ......................................................

_?f (2864)

BASE 4 From Dwg. 21 D152637 Rev. 1

18-BC51 D2-3 7

|nsta||er's Guide

CHECKOUT PROCEDURE

After installation has been completed, it is recommended that the entire system be checked against the following list:

1. Refrigerant Line, Leak checked .................................. [

2. Suction Lines and Fittings properly insulated ........... [

3. Have all Refrigerant Lines been secured and

isolated properly? ........................................................ [

4. Have passages through masonry been sealed?

If mortar is used, prevent mortar from coining

into direct contact with copper tubing ........................ [

5. Verify tightness of all electrical connects ................... [

6. Observe outdoor fan during on cycle for clearance

and smooth operation ................................................. [

]

8. Supply registers and return grilles open and

unobstructed ............................................................... [ ]

9. Return air filter installed ............................................ [ ]

10. Thermostat thermometer is accurate. Check

against a reliable thermometer. Adjust per

instructions with thermostat ...................................... [ ]

11. Is correct speed tap being used?

(Indoor blower motor) ................................................. [ ]

12. Operate complete system in each mode to

insure safe operation ................................................... [ ]

7. Indoor coil drain line drains freely. Pour water

into drain pan .............................................................. [

TROUBLESHOOTING CHART m WHAT TO CHECK

SYSTEMFAULTS

REFRIGERANTCIRCUIT

HeadPressure Too High

HeadPressure Too Low

SuctionPressureTooHigh

SuctionPressureTooLow

LiquidBefrig Eloodback(TXV)

IELCoil Frostiag

ELECTRICAL

Compressor& OB Fan

Won't Start

CompressorWill Not Start

But OD EalqRuns

OD FanWon't Start

CompressorHums ButWon't Start

CompressorCycleson I01.

IELBlower Won't Start

DEFROST

UnitWon't Initiate Defrost

DefrostTerminatesonTime

Unit IcingUp

C - Cooling H - Heating

s s

ss ii

s P

s p

P Ss PP

P P

P - PrimaryCauses S - SecondaryCauses "k - 3 PhaseOnly

T J.N£

Trane

A business of

American Standard Companies

www.trane.com

Literature Order Number 2TWR2-iN-1B RI. 2/03

File Number SV-UN-S/SP-2TWR2-1N-1B

Supersedes 2TWR2-1N-1A

Stocking Location PI Louisville & Webb/Mason-Houston

Trane has a policy of continuous product and product data improvement and it reserves the right to change

design and specifications without notice.

TRANE Air Conditioner/heat Pump(outside Unit) Manual L0905065

Navigation menu

Versions of this User Manual:

Views

Navigation