TSC Auto ID Technology RFWKD WIFI Module User Manual
TSC Auto ID Technology Co., Ltd. WIFI Module Users Manual
Contents
- 1. Users Manual
- 2. (RF-WKD) UserMan
Users Manual
RF-WKD Wi-Fi module USER’S MANUAL Copyright Information ©2014 TSC Auto ID Technology Co., Ltd, The copyright in this manual, the software and firmware in the printer described therein are owned by TSC Auto ID Technology Co., Ltd, All rights reserved. Information in this document is subject to change without notice and does not represent a commitment on the part of TSC Auto ID Technology Co. No part of this manual may be reproduced or transmitted in any form or by any means, for any purpose other than the purchaser’s personal use, without the expressed written permission of TSC Auto ID Technology Co. Agency Compliance and Approvals FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: VTV-RFWKD ” and "Contains IC: 10524A-RF-WKD “ Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This device is slave equipment, the device is not radar detection and not ad-hoc operation in the DFS band. This radio transmitter FCC ID: VTV-RF-WKD has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. ARISTOTLE RFA-25-P393B-70-85-L ENTERPRISES INC. ARISTOTLE RFA-25-P393B-70B140R ENTERPRISES INC. Antenna Type Peak Gain FPC 3.2 dBi for 2.4 GHz 3.1 dBi for 5 GHz 0.9 dBi for 2.4 GHz 3.2 dBi for 5 GHz FPC Note: The antenna connector is I-PEX type. Canada, Industry Canada (IC) Notices This device complies with Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body). Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d'une personne). This radio transmitter IC: 10524A-RF-WKD has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Cet émetteur radio IC: 10524A-RF-WKD a été approuvé par Industrie Canada pour fonctionner avec les types d'antennes énumérés ci‐dessous avec le gain maximal admissible et impédance d'antenne requise pour chaque type d'antenne indiqué. Types d'antennes n'est pas inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Antenna List No. Manufacturer Part No. ARISTOTLE RFA-25-P393B-70-85-L ENTERPRISES INC. ARISTOTLE RFA-25-P393B-70B140R ENTERPRISES INC. Note: The antenna connector is I-PEX type. Antenna Type Peak Gain FPC 3.2 dBi for 2.4 GHz 3.1 dBi for 5 GHz 0.9 dBi for 2.4 GHz 3.2 dBi for 5 GHz FPC 1. Introduction Product Introduction The RF-WKD is an 802.11 a/b/g/n Wi-Fi module which supports 2 dual-band external antennas. The module provides serial UART interface, enabling connection to any embedded design utilizing a 32-bit microcontroller via simple commands. The RF-WKD Wi-Fi module is compatible with other devices that use 802.11 a/b/g/n technology. For more information, please refer the contents in this document. 2. Specification 2.1 Hardware Specification 2.1.1 System Block Diagrams Crystal 40 MHz SPI Flash 128 Mbits DDR2 512 Mbits Debug Console Wideband E XT LAN 2.6V or 1.8V 2GHz Rx0 AR9342 MII/RMII /RGMII Internal UART L-Speed LDO for LC type diplexer 5GHz Rx0 SP3T RFSW IPEX0 SP3T RFSW IPEX1 2GHz Tx0 5GHz Tx0 PCI Express Wideband E XT LAN 2GHz Rx1 I2S/ SPDIF 5GHz Rx1 LC type diplexer 2GHz Tx1 USB MAC/PHY UART H-Speed Internal LDO for GPIO Internal SWREG 1.2V 5GHz Tx1 3.1V Wafer 2x7 pin EXT 5V or 3.3V supply External SW-REG 2.1.2 Module Specification CPU Atheros AR9342 RAM DDR2 SDRAM 512Mbits/64MByte Flash 128Mbits/16MByte Antenna 2T2R(2 x I-PEX connector) Output/power UART TXD.RXD.CTS.RTS 3.3VDC/0.5A, baud rate: 9600~115200bps USB USB (device) 5VDC/0.5A 1. Power LED LED indicator 2. WLAN LED Button initial/reset button Console port Reserved for debug 2.1.3 PCB Characteristics Printed Circuit Board: FR4, UL94V-0, 6 Layers Dimension: I/O placement: 14 pins wafer (definition as following) pin definition 3.3V Reset TX CTS RX RTS Wake_up TCP GND 10 GND 11 5V 12 USB D- 13 GND 14 USB D+ 2.1.4 Environmental Conditions Preservation Temperature: -25 ~ 60 ˚C Preservation Humidity: 10~90% non-condensing Operation Temperature: 0 ~ 50˚C Operation Humidity: 10~90% non-condensing 2.1.5 ESD ±8kV for Air Discharge ±4kV for Contact Discharge 2.2. Protocol: Item Protocol FTP client for firmware update RAW TCP printing protocol (Port 9100 printing) LPR Printing Protocol (Port 515 printing) SNMP v1: Get Printer Status. (Print Name, Port Number, Printer Status…) DHCP Client: Station mode BOOTP RARP ARP 2.3. Mechanical Dimension: 3. AT command Convention For every AT command its response is a status, the default response should be an ASCII character byte starting from ‘0’, ‘0’ indicate the request is done successfully , others indicate independent status, but ‘1’ may indicate the request is not complete in certain circumstances. For every AT command its input is defined, the input option with underline indicate the default value for the module. Angle Brackets (“<” and “>”) indicate the value in the brackets is an arbitrary string. Every listed AT command should be ended with two binary character 0x0D 0x0A. AT Commands 3.1. Set UART baud Rate (wait for confirmation for both printer and module) AT+UARTBAUD=n Baud rate 9600 14400 19200 38400 56000 57600 115200 230400 460800 921600 Return status 3.2. AT Command Response Type AT+RESP=n n=0: Single Byte Mode -AT response will be either “0”, “1”, or any single byte n=1: String Mode -AT response will be either “OK” or “Fail”. Return status 3.3. Time Setting (UTC) AT+TIME= YYYY.MM.DD-hh:mm:ss Return status 3.4. Enable/Disable WLAN Interface AT+WACTIVE=n n=0: Disable n=1: Enable Return status 3.5. File Transfer AT+WFILE=, , Return ‘0’ 3.6. Reboot WLAN Module AT+WREBOOT Return ‘0’ 3.7. Reset to Default AT+WRESET Return ‘0’ 3.8. Set Host name AT+WHOSTNAME= Return status 3.9. Wireless LAN Basic Setting 3.9.1. Set WLAN Mode AT+WMODE=n n=1: 11NAHT20 -802.11n A-Band (5GHz) n=2: 11NGHT20 Return status 3.9.2. Set AP/client mode -802.11n G-Band (2.4Gz) AT+WAPMODE=n n=0: client mode n1: AP mode Return status 3.9.3. Enable/Disable DHCP Client AT+WDHCPC=n n=0: Disable n=1: Enable Return status 3.9.4. Static IP, Subnet Mask, Gateway Set AT+WSTATIC= , ,Gateway>, Return status 3.9.5. Set Client Mode SSID AT+WSSID= Return status 3.9.6. Set AP Mode SSID AT+WAPSSID= Return status 3.9.7. Set Wireless Roaming Option AT+WROAM= , m=-30~-90(dBm): Threshold n=0~30 (dB): Delta Return status 3.10. Wireless LAN Security Setting 3.10.1. Set Security Mode AT+WSECURITY=n n=0: None n=1: WEP n=2: WPA/WPA2-PSK n=3: WPA2-EAP Return status 3.11. Wireless LAN WEP Setting 3.11.1. Set WEP Key Index AT+WWEPINDEX=n n=1~4 Return status 3.11.2. Set WEP Key AT+WWEPKEYn= n=1~4 is 10 or 26 hexadecimal digits (or empty to clear the current setting) Return status 3.12. WPA2 Setting 3.12.1. Set WPA2-PSK Key AT+WWPA2PSK= is 8~63 ASCII characters or a 32-byte key formatted as an ASCII hexadecimal number. Return status 3.12.2. Set AP Mode WPA2-PSK Key AT+WAPWPA2PSK= is 8~63 ASCII characters or a 32-byte key formatted as an ASCII hexadecimal number. Return status 3.12.3. Set WPA2-EAP Identity AT+WEAPIDENTITY= , < password > Return status 3.12.4. Set WPA2-EAP Method AT_WEAPMETHOD=n n=0: EAP-TLS n=1: PEAPv0 with EAP-MSCHAPv2 n=2: EAP-TTLS with EAP-MSCHAPv2 Return status 3.12.5. Set WPA2-EAP Certificate File (*.pem) AT+WEAPCERT= , , Type: “0” -> CA Certificate File “1” -> Client Certificate File “2” -> Client Private Key File Size is in unit byte Return status 3.13. Firmware Update Mechanism 3.13.1. Module Firmware Upgrade AT+MFIRMWARE= , Return status *Return “Failed” if firmware checksum error, otherwise “OK”. 3.13.2. FTP Server Check Request AT+MFTPCHECK= , , , , Return <1 byte of status>, <3 bytes of Co nfig size> , <3 bytes of Data size> , <4 bytes of printer firmware size> *status: 0x00: Operation Success (FTP check finished, no need to upgrade firmware) 0x01: Upgrade Printer only 0x02: Upgrade Module only (Module Reboot Required) 0x03: Upgrade both Printer and Module (Module Reboot Required) 0x04: Connecting Refused 0x05: Connection Timeout (Retry 3 Times) 3.14. Status 3.14.1. Get WLAN State AT+WSTATE=? Return , , , Return 0 on any not applicable field. 3.14.2. Get MAC/IP Address AT+WMAC=? Return , , , Return 0.0.0.0 when any not applicable IP. 3.14.3. Get Site Survey Result AT+WSCAN=? Return , , , , , ; , , , , , ; …. 3.14.4. Get Module SNMP Information AT+WSNMPINFO=? Return , , , , , , , , , , , , , , , , , , , , , , 3.14.5. Get Hostname AT+WHOSTNAME=? Return 4. Network command Format To ensure all transfers over UART are operating as expectation, each transfer is required to include the following fields: ● An Opcode which defines the specific operation, the operation may be different between the Printer and the Module. ● A transfer size designates the whole size of this transfer. Target should drop this transfer and acknowledge Initiator with error when received size is different to this value. * All the fields denoted in transfers are adhering to Network Byte Order (Big Endian). Transfer Commands: Printer Command Set: Data Write Command: This command provides function for Initiator to write data to Target. Initiator Request: Opcode Transfer size Data Checksum Value 0x1100 Size Data Reserved Size (Byte) <16M Opcode Transfer size F/W Ver. Checksum Value 0xFF00 Size Version* Reserved Size (Byte) Module Ready Signal: Module Request: *Version: String: [MAJOR NUMBER].[MINOR NUMBER].[BUILD NUMBER] AT Command: Printer can communicate AT command with Module in following format. Initiator Request: Opcode Transfer size Data Checksum Value 0x2000 Size AT command Reserved Size (Byte) <16M Opcode Transfer size Data Checksum Value 0x2000 Size AT Response Reserved Size (Byte) <16M Target Response: NT Command: Printer can establish connection through NT command in following format. Initiator Request: Opcode Transfer size Data Checksum Value 0x3000 Size NT command Reserved Size (Byte) <16M Opcode Transfer size Data Checksum Value 0x3000 Size NT response Reserved Size (Byte) <16M Target Response: Network Command Set: Printer can establish connection through commands below. Network Open Command: (Printer Only) NT+SOCKETOPEN= , , : “0” -> TCP Socket Connect “1” -> TCP Socket Accept “2” -> UDP Socket Open Return Socket SetOpt Command: NT+SETSOCKETOP= ,
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Jinn-pc_2 Create Date : 2015:01:15 17:02:27+08:00 Modify Date : 2015:01:15 17:02:27+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Title : Microsoft Word - 使用手冊_TSC RF-WKD manual Creator : Jinn-pc_2 Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:baf07d60-dd75-4b03-9b04-e5823ce98638 Instance ID : uuid:947d5b0c-a837-41aa-9d32-b0387b7aaf8c Page Count : 19EXIF Metadata provided by EXIF.tools