TYCOFETY KANTECH 15KTMULMTKP Smart Card Reader User Manual My

TYCO SAFETY PRODUCTS / KANTECH Smart Card Reader My

Users Manual

SmartCard ReaderMullion Single GangTechnical SpecificationsModel KT-MUL-MT-KP / KT-MUL-MT KT-MUL-SC-KP / KT-MUL-SC KT-SG-MT-KP / KT-SG-MT KT-SG-SC-KP / KT-SG-SCTypical Read Range 13.56 MHz MIFARE Plus X,encrypted sector, ID-1 Credentials (Cards) Up to 1.2" Up to 1.6"Typical Read Range 125 kHz ioProx ID-1Credentials (Cards) Up to 1.8" - Up to 2.0" -Input Voltage 5VDC to 15VDCPower Consumption @ 12V 175mA 70mA 160mA 70mA 175mA 70mA 160mA 70mAOperating Humidity 0 to 95% non-condensingOperating Temperature -40C to +70C (-40F to +158F)Environmental Rating IP57Dimensions (H.W.D.) mm 115.8 x 44.6 x 24.7 115.8 x 71.5 x 24.7Dimensions (H.W.D.) in 4.56 x 1.75 x 0.97 4.56 x 2.81 x 0.97Weight 108g (0.24lb) 106g (0.23lb) 105g (0.23lb) 103g (0.23lb) 173g (0.38lb) 166g (0.37lb) 170g (0.37lb) 161g (0.35lb)Housing Polycarbonate, Smoked BlackRF Technologies 13.56 MHz and 125 kHz 13.56 MHz 13.56 MHz and 125 kHz 13.56 MHzCapacitive Touch Keypad with backlighting x x x xLED Indicator Multi-Color Bar: Red, Green, Yellow, Blue, ConfigurableSounder IntegratedTamper OpticalInputs Wiegand or RS-485: LED and Buzzer RS-485: 2 to 4 (configurable, using double device)Output RS-485: 1 supervised, open-drain, up to 750mAWiring Terminal 6 Screwless PolesMounting Mullion North American Single GangCommunication RS-485 Bus AES-128 Encrypted or WiegandWiegand Formats 26-bit / 34-bit / Kantech XSF / Kantech SSFSupported Credentials 13.56MHz125kHzMIFARE Plus X and ISO/IEC 14443AioProx - ioProx -Cabling 3 Twisted pairs AWG 22 unshielded, up to 250' (75m)Security Supports AES-128 Encryption between the Credential and the Reader as well as between the Reader and the Access ControllerFirmware Fully upgradable via RS-485Certifications FCC, CE, UL, NIST, FIPS 197, RoHS, WEEEFlammability Rating UL94 V-0Warranty Limited LifetimeCompatible Access Control Units:Wiegand XSF KT-300, KT-400 and KT-1Wiegand SSF KT-300, KT-400 and KT-1RS485 KT-400 and KT-1
SmartCard ReaderMounting InstructionsFollow these instructions to install the reader:1. Pull the controller’s wires in the wall through the hole in the mountingbracket.2. Affix the mounting plate to the wall using two screws (#6-32).3. If a higher level of tamper detection is desired, cut the plastic tampertab from the mounting bracket.4. Secure the white reflector tab back into the mounting plate hole with ascrew. (#6-32).5. After having wired the reader as per the drawings below, insert the tophook of the cover into the mounting plate tab and complete the pro-cedure by pressing the bottom part into place until the bottom hook is inplace.6. If a more secure installation is desired, install the provided screw at thebottom of the reader. You may also use the provided security screwinstead for an even safer installation. (#6-32).FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by KANTECH could void your authority to usethis equipment.This equipment generates and uses radio frequency energy and if not installed and used properly, in strictaccordance with the manufacturer’s instructions, may cause interference to radio and television reception. Ithas been type tested and found to comply with the limits for Class B device in accordance with the spe-cifications in Subpart “B” of Part 15 of FCC Rules, which are designed to provide reasonable protectionagainst such interference in any residential installation. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause interference to television or radio reception,which can be determined by turning the equipment off and on, the user is encouraged to tryto correct the inter-ference by one or more of the following measures:-Re-orient the receiving antenna-Relocate the alarm control with respect to the receiver-Move the alarm control away from the receiver-Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.If necessary, the user should consult the dealer or an experienced radio/television technician for additionalsuggestions. The user may find the following booklet prepared by the FCC useful: “How to Identify andResolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Print-ing Office, Washington D.C. 20402, Stock # 004-000-00345-4.INDUSTRY CANADA STATEMENTCAN-ICES-3(B)/NMB-3(B)Wiring Chart via Wiegand Wiring Chart via RS485Wiring Chart via RS485 (Lock Wiring)UL294 Performance Levels:Destructive Attack: Level I (no attack test)Line Security: Level III (AES128 line security)Endurance: Level IV (100,000 cycles)Standby Power: Level I (no integral standby power)Installation location and wiring methods shall be in accordance with theNational Electrical Code, ANSI/NFPA 70. There is no maintenancerequired and there are no replacement parts required for these devices._____________________________________________________________________________________________________________________This device complies with Part 15 Class B of the FCC rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received includinginterference that may cause undesired operation. This class B digital apparatus meets all requirements of the Cana-dian Interference Causing Equipment Regulations CAN ICES-3 (B) / NMB-3 (B).MullionFCC ID: V8515KTMULMTKPIC: 5690B-KTMULMTKPSingle GangFCC ID: V8515KTSGMTKPIC: 5690B-KTSGMTKPCopyright © 2015 Tyco International Ltd. and its Respective Companies. All rights reserved • Specifications may change without noticeTel.: 1 (450) 444-2030 • Toll Free: 1-888-222-1560 • Fax: 1 (450) 444-2029 • www.kantech.comD29009033R001Models:KT-MUL-MT and KT-MUL-MT-KP FCC ID: V8515KTMULMTKP IC: 5690B-KTMULMTKP . Models: KT-SG-MT and KT-SG-MT-KP FCC ID: V8515KTSGMTKP IC: 5690B-KTSGMTKPModels: KT-MUL-SC and KT-MUL-SC-KP FCC ID: V8515KTMULSCKP IC: 5690B-KTMULSCKP . Models: KT-SG-SC and KT-SG-SC-KP FCC ID: V8515KTSGSCKP IC: 5690B-KTSGSCKPThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Navigation menu