TYSON BIORESEARCH HT100 Blood Glucose Meter User Manual HT100 C Manual LAY FDA AF004 0027000N 180117

Download:
Mirror Download [FCC.gov]
Document ID	3730057
Application ID	9uaBAZ8QmcDqiUglVCJLfQ==
Document Description	Users Manual_HT100_C
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	100.86kB (1260710 bits)
Date Submitted	2018-01-26 00:00:00
Date Available	2018-07-26 00:00:00
Creation Date	2018-01-17 13:08:23
Producing Software	Adobe PDF library 15.00
Document Lastmod	2018-01-17 13:08:24
Document Title	HT100_C_Manual_LAY_FDA_AF004-0027000N_180117
Document Creator	Adobe Illustrator CC 22.0 (Windows)

Limitations
The Tyson Bio HT100-C Blood Glucose Test Strips give accurate results when the following limitations are observed.
˙Use only capillary whole blood from finger, palm, and forearm.
˙Do not use for testing neonatal blood.
˙Altitude higher than 10745 feet may cause inaccurate results.
˙Severe dehydration and excessive water loss may lead to inaccurate blood glucose test results.
Consult your physician immediately if you believe you are suffering from severe dehydration.
˙For single-patient use only and should not be shared.
˙Should not be used to test critically ill patients.
˙Inaccurate results may occur in severely hypotensive individuals or patients in shock.
˙Inaccurate low results may occur for individuals experiencing a hyperglycemic-hyperosmolar state, with or without ketosis.
˙For In vitro diagnostic only.
˙For over the counter use.
˙Alternative site testing should be performed only during steady-state (when glucose is not changing rapidly).
˙Alternative site measurements should never be used to calibrate continuous glucose monitors (CGMs).
˙Alternative site measurements should never be used for insulin dosing calculations.
Warning
•This device is not intended for use in healthcare or assisted-use settings such as hospitals, physician
offices, or long-term care facilities because it has not been cleared by FDA for use in these settings,
including for routine assisted testing or as part of glycemic control procedures.
•Use of this device on multiple patients may lead to transmission of Human Immunodeficiency Virus (HIV),
Hepatitis C Virus (HCV), Hepatitis B Virus (HBV), or other bloodborne pathogens.
Table of Content
Limitations
Introduction
Important Safety Instructions
About Tyson Bio HT100-C Blood Glucose Monitoring System
About Tyson Bio HT100-C Blood Glucose Meter
About Tyson Bio HT100-C Blood Glucose Meter Display
About Tyson Bio HT100-C Blood Glucose Test Strip
Tyson Bio HT100-C Blood Glucose Test Strip
Setting Up Tyson Bio HT100-C Blood Glucose Meter
Installing/Replacing Batteries
Date/Time Setup
Reminder Alarms Setup
HI/LO Alarms Setup
Important Information
Using Tyson Bio HT100-C Blood Glucose Test Strip
Obtaining a Blood Sample
Applying a Blood Sample
HI and LO Readings
Available Alternate Sites Testing
01
02
03
04
05
06
07
08
08
08
09
10
11
12
13
14
15
16
Table of Content
Control Solution
Performing a Control Solution Test
Control Solution Results
Memory Features
View Day Average Results
Exiting the Memory Mode
Transfer Test Results to a Computer
Voice Guidance
Bluetooth Guidance
Cleaning and Disinfection Procedure
Care and Storage
Display Messages
Error Messages
Trouble Shooting
Specifications
Meter Storage
Icon Description
Service and Warranty
17
17
18
19
20
21
21
22
23
26
28
29
31
33
34
35
35
36
Introduction
Thank you for choosing Tyson Bio HT100-C Blood Glucose Monitoring System to monitor your blood glucose (sugar) level.
It is accurate, easy to use, and quick in response time. This User Manual contains all information needed to operate and
maintain Tyson Bio HT100-C Blood Glucose Monitoring System. Please read carefully before use.
Tyson Bio HT100-C Blood Glucose meter can be used with:
˙Tyson Bio HT100-C Blood Glucose Test Strip
Intended Use Statement
The Tyson Bio HT100-C Blood Glucose Monitoring System is intended for the quantitative measurement of glucose in fresh
capillary whole blood samples drawn from the fingertips, forearm, or palm. Alterative site testing should be performed
only during steady-state (when glucose is not changing rapidly). Testing is done outside the body (In Vitro diagnostic use).
It is intended for self-testing by people with diabetes at home as an aid to monitor the effectiveness of diabetes control.
It should only be used by a single patient and it should not be shared. It is not indicated for the diagnosis of or screening
for diabetes or for neonatal use.
The Tyson Bio HT100-C Blood Glucose Monitoring System is comprised of the Tyson Bio HT100-C Blood Glucose Meter and
Tyson Bio HT100-C Blood Glucose Test Strip.
01
Important Safety Instructions
˙All parts of the system should be considered potentially infectious and are capable of transmitting blood-borne
pathogens between patients and healthcare professionals.
˙The meter and lancing device are for single person use. Do NOT share them with anyone including other family
members!
˙All parts of the kit are considered biohazardous and can potentially transmit infectious diseases, even after you
have performed cleaning and disinfection.
˙Cleaning Solution and Disinfecting Solution: Clorox Bleach Germicidal Wipes (Clorox Professional Products Company. EPA
Reg. No. 67619-12).
Reference:
˙“ FDA Public Health Notification: Use of Fingerstick Devices on More than One Person Poses Risk for Transmitting
Bloodborne Pathogens: Initial Communication” (2010)https://www.fda.gov/MedicalDevices/Safety/AlertsandNotices/
ucm234889.htm
˙“ CDC Clinical Reminder: Use of Fingerstick Devices on More than One Person Poses Risk for Transmitting Blood-borne
Pathogens” (2010) http://www.cdc.gov/injectionsafety/Fingerstick-DevicesBGM.html
˙“ CDC: Infection Prevention during Blood Glucose Monitoring and Insulin Administration” (2010) https://www.cdc.gov/
injectionsafety/blood-glucose-monitoring.html
02
About Tyson Bio HT100-C Blood Glucose Monitoring System
The complete kit contains:
˙HT100-C Blood Glucose Meter
˙HT100-C Blood Glucose Test Strip (10 strips)
˙HT100-C Control Solution Level 2
˙Adjustable Automatic Lancing Device
˙10 Sterile Lancets
˙User Manual
˙Quick Reference Guide
˙Test Strip Package Insert
˙Control Solution Package Insert
˙Log Book
˙Carrying case
Note: 25-strips & 50-strips are sold separately.
03
About Tyson Bio HT100-C Blood Glucose Meter
1. Data Port
2. Display
3. Button
To connect interface cable for data transferring
To display results in numbers and icons
Press and hold to enter reminder alarm and HI/LO alarm setup
To adjust numbers and to toggle settings
To browse test results and averages in memory
4. Button
Press and hold to enter buzzer setup
To adjust numbers & to toggle settings
To browse test results and averages in memory
5. Button
Press and hold to enter the year/date/time setting
To browse Control Solution test results
To turn the meter ON/OFF
6. Strip Ejector
Push to eject the test strip
7. Test Port
The test strip is inserted here
8. Battery Cover To slide open and close
9. Meter Label
Manufacturer information
10. Serial Numbers The meter manufacturer serials
04
About Tyson Bio HT100-C Blood Glucose Meter Display
10
11
12
13
14
15
16
1. Memory Icon
Memory mode
2. Year/Date
Display year/date
3. Control Solution Icon
Control Solution test mode and Control Solution test result
4. Alarm Icon
Reminder alarm
5. Test Result
Result display
6. Buzzer Icon
When buzzer is ON
7. Meal Indicator Icon
Pre-meal and post-meal
8. 14 day Average
14 day average result
9. Time
Time display
10. Blood Drop Icon
Flashes when the meter is ready to accept your
blood sample to test
11. Warning Icon
Appears when a result is out of range
12. Test Strip Icon
Appears when the meter is ready for a test
13. Temperature Icon
Appears when the meter exceeds normal operating
temperatures
14. Measurement Units
To identify test result units (mg/dL)
15. Battery Icon
Appears when battery power is low
16. Bluetooth icon
When Bluetooth is on
Note: The mg/dL is the standard unit in the United States. Meters used in the United States must be set to read in mg/dL".
05
About Tyson Bio HT100-C Blood Glucose Test Strip
Tyson Bio HT100-C Blood Glucose Test Strip is only for Tyson Bio HT100-C Blood Glucose Meter.
Use each strip ONCE ONLY!
A test strip consists of the following parts:
1. Target Area
Where a blood drop or control solution to be applied
2. Confirmation Window
To confirm sufficient blood sample and control solution
3. Contact Bar
To be inserted into the test port and to activate the meter (top side up)
top side
06
Tyson Bio HT100-C Blood Glucose Test Strip
Tyson Bioresearch, Inc.
5F., No. 16, 18, 20, 22, Kedong 3rd Rd.,
Zhunan Township, Miaoli County 35053,
Taiwan
Tel : +886-37-585998
Customer Service
U.S.A. +1-800-948-3894
30˚C
4˚C
HT100
Blood Glucose Test Strips
Use within 1 months after first opening.
Do not use past the expiration date.
Use Tyson Bio HT100-C meter only !
HT100-C
Control Solution Range
Level 1:
mg/dL
Level 2:
mg/dL
Level 3:
mg/dL
Test Strip Vial Label
AL001-0119000N (01) Rev. date: 12/2016
HT100-C
Store at 39 ~ 86°F (4 ~ 30°C), 10~90% RH.
Do not refrigerate.
Do not store test strips outside this vial.
Re-cap immediately.
WARNING: Always close cap tightly.
For testing of glucose in capillary whole blood.
Store at 39 ~ 86°F (4 ~ 30°C), 10~90% RH.
Do not refrigerate.
Do not store test strips outside this vial.
Re-cap immediately.
WARNING: Always close cap tightly.
For testing of glucose in capillary whole blood.
Tyson Bioresearch, Inc.
5F., No. 16, 18, 20, 22, Kedong 3rd Rd.,
Zhunan Township, Miaoli County 35053,
Taiwan
Tel : +886-37-585998
Customer Service
U.S.A. +1-800-948-3894
30˚C
4˚C
Blood Glucose Test Strips
Use within 1 months after first opening.
Do not use past the expiration date.
Use Tyson Bio HT100 meter only !
Control Solution Range
Level 1:
mg/dL
Level 2:
mg/dL
Level 3:
mg/dL
Test Strip Vial
07
Setting Up Tyson Bio HT100-C Blood Glucose Meter
˙Make sure the batteries are properly installed
˙The default is set to January 1st, 0:00
˙Please follow instructions to properly setup the meter
Installing/Replacing Batteries
1. Slide and remove the battery cover (Fig.1).
2. Install batteries with the + and – ends matching indication marks
on the battery compartment (Fig.2).
3. Slide battery cover back into place (Fig.3).
(Fig.1)
(Fig.2)
(Fig.3)
Date/Time Setup
1. When the meter is off, press and hold for 4 seconds to enter this setting mode. (with the voice function on, you will
hear "Please set date and time.")
2. Press or to select “24hr” or “12hr”.
3. Press to confirm (Fig.4).
4. The numbers of “year” will appear and flash. Press or to adjust and Press to confirm (Fig.5).
5. The number of “month” will appear and flash. Press or to adjust and press to confirm (Fig.6).
6. The numbers of “date” will appear and flash. Press or to adjust and press to confirm (Fig.7).
7. The numbers of “hour” will appear and flash. Press or to adjust and press to confirm (Fig.8).
08
(Fig.4)
(Fig.5)
(Fig.6)
(Fig.7)
(Fig.8)
8. The numbers of “minute” will appear and flash. Press or
adjust. Press to confirm (Fig.9).
9. The set date and time will now be displayed on screen
(Fig.10, Fig.11). Press to turn off the meter.
10. The meter date/time setting is complete.
to
(Fig.9)
Reminder Alarms Setup
(Fig.10)
(Fig.11)
Tyson Bio HT100-C meter provides 4 reminder alarms. All reminder alarms are OFF as default. Please follow these steps to
setup reminder alarms.
1. When the meter is OFF, press and hold for 4 seconds or longer to enter setting. (with the voice function on, you will
hear " Please set reminder alert".)
2. The first reminder alarm will appear on the display (Fig.12).
3. Press or to select “ON” or “OFF”.
4. If “OFF” is chosen and pressed, the meter will proceed to the next reminder alarm setting. If “ON” is chosen (Fig.13) and
pressed, the number of “hour” will start flashing (Fig.14). Press or to adjust and press to confirm.
5. The numbers of “minutes” will flash (Fig.15). Press or to adjust and press to confirm. The meter will go to the next
reminder alarm setting.
6. Repeat steps 3 to 5 to set the rest of reminder alarms.
(Fig.12)
(Fig.13)
(Fig.14)
(Fig.15)
09
HI/LO Alarms Setup
1. Press
to enter the HI alarm setting after completing the reminder alarm setup. (with the voice function on, you will
hear "Please set your alert value".)
2. Press
or
to set “ON" and press
3. To change the alarm setting, press
to confirm. If "OFF" is chosen, the meter will skip this setting (Fig.16, 17).
or
until you reach your desired HI setting and then press
to confirm. (Fig.18)
The HI alarm value range is 100 ~ 400mg/dL and the default value is 180mg/dL. (with the voice function and HI Alarm on,
you will hear "please set hyperglycemic value".)
4. Continue to the LO alarm setting (Fig.19), repeat Step 2 and 3 (Fig.20, 21) to confirm or to change LO alarm setting.
The LO alarm value range is 40 ~ 90mg/dL and the default value is 70mg/dL. (with the voice function and LO Alarm on,
you will hear "please set hypoglycemic value".)
5. Press
to finish setting and the meter will be turned off.
(Fig.16)
(Fig.17)
(Fig.18)
(Fig.19)
(Fig.20)
(Fig.21)
NOTE:
The hypoglycemic (LO) and hyperglycemic (HI) alarm glucose values should be selected in consultation with your
health care provider.
You will hear "The meter will switch off shortly." if no further action.
10
Important Information
Before Testing
˙Always keep test strips in the original vial. The vial contains drying agents to protect the test strips from moisture.
˙Tightly close the vial cap immediately after removing a test strip.
˙Use each strip immediately after removing it from the vial.
˙Use each test strip ONCE ONLY.
˙Do not use the test strips or Control Solution beyond the expiration date printed on the package. This may cause
inaccurate results.
˙Do not use the test strips or Control Solution if the package is damaged.
˙Store your test strips and the Control Solutions between 39°F ~ 86°F (4°C ~ 30°C)
Temperature beyond this range can damage test strips and lead to inaccurate results.
˙Any change of medications based on the Tyson Bio HT100-C Blood Glucose Monitoring System results without advices of
a doctor is NOT RECOMMENDED.
˙The lancing device is intended only for single user and should NOT be shared.
˙Users should wash hands thoroughly with soap and water after handling the meter, lancing device, or test strips.
˙Only Tyson Bio HT100-C Test Strip and Control Solution can be used with the Tyson Bio HT100-C Blood Glucose Meter.
11
Using Tyson Bio HT100-C Blood Glucose Test Strip
You need the following items to test
˙Tyson Bio HT100-C Blood Glucose Meter
˙Tyson Bio HT100-C Blood Glucose Test Strip
˙Adjustable automatic lancing device and sterile lancet
Preparing the Test Strip
1. Wash hands using soap and warm water. Rinse and dry thoroughly (Fig.22).
2. Please remove protective wrap completely before opening the vial.
3. Take a test strip from the vial and re-cap immediately (Fig.23).
4. Insert the test strip top side up into the test port (Fig.24). The meter will be automatically turned on.
5. System checking will appear (Fig.25). (with the voice function on, you will hear " System checking".)
6. A beep will sound and following by a flashing “ ” icon. (with the voice function on, you will hear " Please apply blood
sample.") You can press or to select the meal indicator for marking the test as (Fig.26):
˙Pre-Meal Test
(with the voice function on, you will hear" Pre-meal, please apply sample.")
˙Post-Meal Test (with the voice function on, you will hear" Post-meal, please apply sample.")
˙No marker as default
7. A blood sample can now be obtained (refer to P.13).
(Fig.22)
12
(Fig.23)
(Fig.24)
(Fig.25)
(Fig.26)
Obtaining a Blood Sample
1. Unscrew the lancing device cap (Fig.27).
2. Place a lancet into the lancing device (Fig.28).
3. Twist and pull to remove the protective lancet cover to expose the sterile needle. Save the cap for later use (Fig.29).
4. Screw the lancing device cap back on. Select the skin penetration depth preferred (Fig.30).
5. Pull the barrel back until you hear a 'click' (Fig.31).
6. Place the lancing device against the finger, palm, or forearm. Press the trigger to obtain a blood sample (Fig.32).
To unload the lancing device
1. After sampling, carefully remove the cap containing the used lancet.
2. Push the exposed tip of the lancet into its Protective Cap (Fig.33).
Slide the Lancet Ejector forward and dispose the used lancet in an appropriate container.
For further instructions please see the insert provided with the lancing device.
(Fig.27)
(Fig.28)
(Fig.29)
(Fig.30)
(Fig.31)
(Fig.32)
(Fig.33)
CAUTION:
To reduce chances of infection:
˙Lancets are for single usage only.
˙Wash hands thoroughly with soap and water before and after handling the meter, lancing device, and test strips.
˙Please refer to section "Cleaning and Disinfection Procedure" (refer to P.25) for detail instructions of meter
maintenance.
13
Applying a Blood Sample
SAMPLE MAY BE OBTAINED FROM FINGER, PLAM, OR FOREARM
1. Introduce the tip of the test strip to the drop of blood. Blood sample will be automatically drawn into the test strip
(Fig.34) Discard the first drop of blood sample to prevent contamination.
2. Hold the tip of the test strip touching the blood drop until the meter beeps.
3. The meter will start to countdown as soon as the blood has completely filled the confirmation window of the test strip.
If applying an insuffcient blood sample, the error code (E-7) will appear on the display (Fig.35).
4. The test result will appear on the display in 5 seconds (Fig.36). (with the voice function on, you will hear "Blood glucose
test result is ... milligram per deciliter.") All results will be automatically stored into the meter memory (Fig.37).
5. The meter will automatically turn off after 2 minutes. You will hear "The meter will switch off shortly." if no further action.
6. After completing the test, push the strip ejector (Fig.38) or use a tissue paper to remove the test strip.
Sufficient
Blood
Insufficient
Blood
(Fig.37)
(Fig.35)
(Fig.36)
(Fig.38)
Warning:
˙DO NOT point the test strip at anyone when ejecting.
˙Used lancets and test strips are considered bio-hazardous. Dispose of used lancets and test strips in a clinical waste container
(Fig.34)
Normal Glucose Values
Before a meal (fasting) : <100 mg/dL
2 h after a meal: < 140mg/dL.
These ranges were cited from the American Diabetes Association, Classification and Diagnosis of Diabetes, 2017.
Diabetes Care 40(Suppl. 1):S11–S24
14
HI and LO Readings
˙Tyson Bio HT100-C Blood Glucose Meter is designed to display test results between 20 ~ 600 mg/dL.
˙If “HI” (Fig.39) appears on the display, it indicates the reading is higher than 600 mg/dL.
˙If “LO” (Fig.40) appears on the display, it indicates the reading is lower than 20 mg/dL.
(Fig.39)
(Fig.40)
We suggested the testing procedure should be reviewed and the test should be repeated using a new test strip
to reconfirm the test result.
15
Available Alternate Sites Testing
Palm and Forearm
Tyson Bio HT100-C Blood Glucose Monitoring System provides you alternate sites
testing (AST). This system allows you to test on the palm and the forearm with the
equivalent results to fingertip testing.
Physiological differences in the circulation between the finger and other test sites may
result in differences in blood glucose measurements. Changes in blood glucose may be
observed in finger blood samples sooner than blood samples from the alternate sites.
If you are testing for hypoglycemia (low blood glucose), we recommend that you test
on your fingertips.
AST ONLY in the following intervals:
˙In a pre-meal or fasting state
(more than 2 hours since the last meal)
˙Two hours or more after taking insulin
˙Two hours or more after exercise
DO NOT use AST if:
˙You think your blood glucose is low
˙You are unaware of hypoglycemia
˙Your AST results do not match the way you feel
˙You are testing for hyperglycemia
˙Your routine glucose results are often fluctuating
16
Palm
Forearm
There are limitations for doing AST.
Please consult your healthcare
professional before you do AST.
AST measurements should not be used to
calibrate continuous glucose monitors
(CGMs).
AST measurements should not be used for
insulin dose calculations.
Control Solution
The Control Solution is to ensure that Tyson Bio HT100-C Blood Glucose Monitoring System is working properly and you are
performing a test correctly.
When to Perform a Control Solution Test
1. You use the meter for the first time.
4. Your test results are not consistent with how you feel.
2. You use a new vial of test strips.
5. You think your test result is not accurate.
6. You damage your meter.
3. You suspect that the meter or test
strips are not working properly.
7. An advice from your healthcare professional.
Note: Please read the Control Solution package insert for more detail information.
Performing a Control Solution Test
1. Be sure of the Control Solution is at a room temperature between 59°F ~ 95°F (15°C ~ 35°C) before
testing.
Control solution that is not at room temperature when tested may cause out of range results.
2. Insert a Tyson Bio HT100-C test strip, top side up, contact bar end first, into the test port. The meter will
be automatically turned ON (Fig.41).
3. A beep will sound and the system checking will appear followed by a flashing “ ” icon (Fig.42). (with the
voice function on, you will hear " Please apply blood sample.")
(Fig.41)
(Fig.42)
17
4. Press and hold for 2 seconds to change to the Control Solution test mode. "
" will appear on the display
(Fig.43). (with the voice function on, you will hear "Please apple control solution.") Press again for 2 seconds and
the meter will switch back to the normal testing mode. (with the voice function on, you will hear " Please apply blood
sample.")
5. Discard the first drop of the Control Solution. Squeeze a small drop on a clean nonabsorbent surface e.g. wax paper
Do not apply the Control Solution to the test strip directly from the bottle because contamination may occur (Fig.44)
6. Introduce the tip of the test strip to the Control Solution drop. The Control Solution will be automatically drawn into
the strip. Hold until the meter beeps. The meter will now start to count down and the Control Solution test result will
appear on the LCD screen (Fig.45). (with the voice function on, you will hear "Control solution test result is ... milligram
per deciliter.")
Caution:
Follow the above instructions when performing a
Control Solution test in order to prevent contamination.
Control Solution Results
(Fig.43)
(Fig.44)
(Fig.45)
The Tyson Bio HT100-C Blood Glucose Monitoring System is working properly only if the Control Solution test result is
within the specified range printed on the test strip vial. Please repeat the test when the test result is out of range.
Out of range result may be caused by:
˙Incorrect steps while performing the test
˙The Control Solution temperature is lower than 59°F (15°C) or higher than 95°F (35°C)
˙Expired or contaminated Control Solution
˙Expired or contaminated test strips
˙Meter malfunction
18
Note:
˙The result will not be included in any day average calculation when the Tyson Bio HT100-C Blood Glucose meter is
set in the Control Solution test mode.
˙DO NOT use Tyson Bio HT100-C Blood Glucose meter if the problem persists. Please contact customer service
immediately.
Memory Features
1. Press to turn on the meter when the meter is off.
2. Press to view previous results. (with the voice function on, you will hear" review history test records.")
˙“ MEM” icon will be displayed on the top center area.
˙“ Year” will be display on the top left corner (Fig.46).
˙After 1 second “Month-Day” will then be displayed on the top left corner.
˙“ Time” will be displayed on the top right corner (Fig.47).
˙The most recent memory results will be displayed first.
3. You can press or to scroll forwards and backwards.
4. Press to exit and view the Control Solution test result (Fig.48).
5. When the meter displays the last stored test result, press so the meter will display day average results (Fig.49).
(Fig.46)
(Fig.47)
(Fig.48)
(Fig.49)
Note:
˙The meter stores 500 results in the memory.
˙When the memory is full, the oldest result will be replaced by the most recent result.
19
View Day Average Results
1. Press to turn on the meter.
2. Press button to view day average results. (with the voice function on, you will hear "Review average value.")
3. 7/14/30 day average results marked with a no meal/ pre-meal/ post-meal and will be displayed on screen in sequence
when is pressed (Fig.50~ 57).
4. When the meter displays 7 days with no meal status assigned, press button and the meter will change to view
results in memory.
(Fig.50)
(Fig.51)
(Fig.52)
(Fig.53)
(Fig.54)
(Fig.55)
(Fig.56)
(Fig.57)
Note:
1. The 7/14/30 day average is calculated from the test results obtained during the last consecutive 7/14/30 day
periods.
2. A result with a temperature warning symbol will NOT be calculated in 7/14/30 day average.
3. “LO” under 20 mg/dL and “HI” over 600 mg/dL readings will NOT be stored in the memory.
20
Exiting the Memory Mode
1. When the meter displays a Control Solution test result, press will turn the meter off.
2. The meter will also be turned off automatically after 2 minutes following the last key pressed.
To Record Your Results
We provide a log book for you to record. Please refer to the log book for details.
Transfer Test Results to a Computer
You can use Tyson Bio PC Link to transfer test results to your personal computer. Obtain the required software and cable to
be ordered separately. For order information please call Customer Service or visit website of www.tysonbio.com
1. Follow the instructions provided with software to install the software into your personal computer.
2. Connect the interface cable to a serial port on your computer while the meter is off.
3. Connect the other end of interface cable to the data port located on the side of the meter.
4. The word "PC" will appear on the display indicates that the meter is now in the communication mode (Fig.58)
(Fig.58)
21
Voice Guidance
Voice Guidance Setup
˙Press to turn on the meter.
will appear. (Fig.59)
˙The voice guidance feature is “ON” by default.
˙Please proceed the following steps
1. When the meter is switched off, press and hold for 4 seconds to enter into setting mode.
2. Press or to select “ON”(Fig.60) or “OFF” (Fig.61). A beep will sound when voice is set “ON”.
(Fig.59)
3. Press to confirm.
4. If the voice is set on, press or to select voice volume. The numbers of “volume” will appear and flash. Press or
to adjust from 1 to 15 (Fig.62).
5. Press to confirm.
6. “L1” or “L2” will appear and flash. Press or to select a Language (Fig.63).
7. Press to confirm.
Note: L1 is English (default) / L2 is Spanish
(Fig.60)
22
(Fig.61)
(Fig.62)
(Fig.63)
Bluetooth Guidance
Bluetooth Setup
˙Press
to turn on the meter. will appear when HT100-C has been detected (Fig. 64)
˙Bluetooth is OFF by default.
˙Please proceed the following steps.
To Transfer Memory Data
1. When the meter is switched ON, hold for 4 seconds to enter Bluetooth mode. will appear and flash on the meter when
meter is not connected with a mobile device (Fig. 65).
2. Turn on BLE tool APP (with Blood Glucose Test) and Bluetooth on your mobile device.
3. Click “Connect” and select the device shown (ex. TBMTXXXXXXXX) in APP list. stops blinking when
the meter & mobile device is connected.
4. Press the button on APP to transfer data. The meter will display while data are biing transferred (Fig. 66)
(Fig.64)
(Fig.65)
(Fig.66)
23
To Connect via Bluetooth before a Blood Glucose Testing
1. When the meter is switched off, press and hold
button for 4 seconds to enter setting.
2. Press to confirm Buzzer setting and enter Bluetooth function setting menu.
3. Press or to select Bluetooth “ON” or “OFF” (Fig. 67).
4. Select “ON” and press to confirm and meter will be turned off.
5. Insert a test strip to turn ON the meter (Fig. 68). will blink when the meter is NOT connected with a mobile device.
6. Turn on BLE tool APP (with Blood Glucose Test) and Bluetooth on your mobile device.
Note: Please skip Step 1~4 if Bluetooth feature is already “ON”.
7. Click “Connect” and select the device shown (ex. TBMTXXXXXXXX) in APP list. stops blinking when the meter &
mobile device is connected.
8. Perform your blood glucose test. After testing your blood glucose, the test result will automatically transmit to the APP.
will disappear (Fig. 69).
(Fig.67)
24
(Fig.68)
(Fig.69)
To Connect via Bluetooth after a Blood Glucose Testing
1. When the meter is switched off, press and hold
button for 4 seconds to enter setting.
2. Press to confirm Buzzer setting and enter Bluetooth function setting menu.
3. Press or to select Bluetooth “ON” or “OFF” (Fig. 70).
4. Select “ON” and press to confirm and meter will be turned off.
5. Insert a test strip to turn ON the meter (Fig. 71). will blink when the meter is NOT connected with a mobile device.
6. After testing your blood glucose, the test result is shown (Fig. 72). Bluetooth icon is still blinking.
Note: Please skip Step 1~4 if Bluetooth feature is already “ON”.
7. Turn on BLE tool APP (with Blood Glucose Test) and Bluetooth on your mobile device
8. Click “Connect” and select the device shown (ex. TBMTXXXXXXXX) in APP list. stops blinking when the meter &
mobile device is connected.
9. The test result will automatically transmit to the APP. will disappear (Fig. 73).
(Fig.70)
(Fig.71)
(Fig.72)
(Fig.73)
25
Cleaning and Disinfection Procedure
Cleaning:
Cleaning removes visible soil, organic material, and most importantly, blood products. Always clean before disinfecting.
The meter should be cleaned whenever it is visibly dirty.
Disinfection:
Disinfection generally refers to the use of chemical and physical agents, such as chemicals, to destroy the potential
inactivity of a material.
The meter should be disinfected periodically, such as twice per week.
Material
Clorox Bleach Germicidal Wipes (Clorox Professional Products Company. EPA Reg. No. 67619-12).
Signs of deterioration
•Performance: The control solution measurements are out of range which is listed on the test strip label.
•Physical: Polymer crazing (thin silver streaks appear), cracking, swelling, dissolving, softing, or becoming brittle,
and the symbols are not clear in LCD display.
If these signs of deterioration are noted, users should stop using meter and contact customer service.
Customer Service
U.S.A. +1-800-948-3894
Taiwan +886-37-585998
24 hours a day, 7 days a week Taiwan
GMT+8, 8:30 ~ 17:30, Monday ~ Friday
Note:
Users should wash hands thoroughly with soap and water after handling the meter, lancing device, or test strips
should be included.
26
Cleaning and Disinfection Procedure
(Step 1)
(Step 2)
(Step 3)
(Step 4)
(Step 5)
(Step 6)
(Step 7)
(Step 8)
(Step 9)
(Step 10)
(Step 11)
(Step 12)
(Step 13)
(Step 14)
(Step 15)
Cleaning:
˙The meter should be cleaned prior to disinfection.
˙Switch the meter OFF.
˙Cleaning solution and disinfecting solution: Clorox Bleach
Germicidal Wipes
˙Use a new cleaning wipe.
˙The meter is cleaned follow by the illustrations
(Step1 ~ Step15).
˙Wipe the entire surface of the meter to clean blood and
other body fluids.
˙Please avoid using alcohol or organic solvents in cleaning.
˙Do not immerse the meter in water. Do not allow water or
cleaning fluids into the meter, test port, and data port.
Disinfection:
˙ Cleaning solution and disinfecting solution: Clorox Bleach
Germicidal Wipes
˙ Use a new disinfection wipe.
˙ The meter is cleaned follow by the illustrations
(Step1~Step15).
˙ Wipe the entire surface of the meter to remove bloodborne
pathogens.
˙ Dispose of the used wipe in a trash bin.
˙ Allow exteriors to remain wet for the 1 minute contact time.
˙ Wipe surface using a towel and allow to air dry.
27
Care and Storage
Please handle the meter with care. Dropping the meter may result in damage.
˙Do not expose the meter, test strips, and the Control Solution to extreme conditions such as high humidity, heat, freezing
cold, or dust.
˙DO NOT STORE IN DIRECT SUNLIGHT OR AREAS WITH HIGH HUMIDITY AND/OR DUST.
˙It is advised that you store all parts of Tyson Bio HT100-C Blood Glucose Monitoring System in the carrying case provided.
28
Display Messages
Display
Description
The system is ready to accept a blood sample.
Action
Apply a blood sample.
The result is HIGHER than the “HI” alert setting.
The default setting is 180 mg/dL and it can be changed
according to 《HI/LO Alarms Setup》
The result is LOWER than the “LO” alert setting.
The default setting is 70 mg/dL and it can be changed
according to 《HI/LO Alarms Setup》
Test result is HIGHER than 600 mg/dL.
Repeat the test by using a new test strip. If the same
message displays again, the result is confirmed to be higher
than the meter test range. Please consult your healthcare
professional immediately for further advice.
Test result is LOWER than 20 mg/dL.
Repeat the test by using a new test strip. If the same
message displays again, the result is confirmed to be lower
than the meter test range. Please consult your healthcare
professional immediately for further advice.
29
Display
30
Description
Action
Temperature is TOO HIGH during the test procedure.
Large variation may occur between results due to high or
low temperature. Move to an environment (50°F ~ 104°F or
10°C ~ 40°C) and wait for 30 minutes before re-testing.
Temperature is TOO LOW during the test procedure.
Large variation may occur between results due to high or
low temperature. Move to an environment (50°F ~ 104°F or
10°C ~ 40°C) and wait for 30 minutes before re-testing.
The preset reminder alarm is ringing
Press any button to turn off the alarm or wait for the alarm to
be turned off automatically in 30 seconds.
Battery power is LOW. Meter will only provide
proximately 10 more measurements.
Replace with 2 AAA batteries.
An error message indicates that the hematocrit of
the hematocrit of the blood sample is too high for
HT100-C system to perform a test.
Follow the instructions and try again with a new test strip.
Please contact customer service if the problem persists.
1. An error message indicates that the hematocrit of
the blood sample is too low for HT100-C system to
perform a test.
2. Use control solution to check the meter and test
strips.
1. Follow the instructions and try again with a new test strip.
Please contact customer service if the problem persists.
2. Follow the instructions to enter control solution mode, and
try again with a new test strip.
Error Messages
Display
Description
Action
Temperature is TOO HIGH to perform a test.
(with the voice function on, you will hear
"Operating temperature error")
Move to an environment between 50°F ~ 104°F or 10°C
~ 40°C and wait for 30 minutes before re-testing.
Temperature is TOO LOW to perform a test.
(with the voice function on, you will hear
"Operating temperature error")
Move to an environment between 50°F ~ 104°F or 10°C
~ 40°C and wait for 30 minutes before re-testing.
Battery power is depleted for further usage.
(with the voice function on, you will hear
"Battery error")
Replace with 2 AAA batteries immediately
An error message indicates a problem with
the test strip. (with the voice function on, you
will hear "Error 1, Strip error")
Review the instructions and try again with a new test strip.
Please contact customer service if the problem persists.
An error message indicates a problem with the
test strip or meter. (with the voice function on,
you will hear " Error 2, Meter error")
Review the instructions and try again with a new test strip.
Please contact customer service if the problem persists.
31
Display
32
Description
Action
An error message indicates a problem with
the meter. (with the voice function on, you
will hear " Error 2, Meter error")
Remove batteries and wait for 1 minute. Reinstall batteries
to see if meter is working properly. Please contact customer
service if the problem persists.
An error message indicates a problem with
the test strip. (with the voice function on,
you will hear "Error 1, Strip error")
Review the instructions and try again with a new test strip.
Please contact customer service if the problem persists.
An error message indicates a problem with
the meter. (with the voice function on, you
will hear " Error 2, Meter error")
Remove batteries and wait for 1 minute. Reinstall
batteries to see if meter is working properly. Please
contact customer service if the problem persists.
An error message indicates a problem with
the test strip. (with the voice function on,
you will hear "Error 1, Strip error")
Review the instructions and try again with a new test strip.
Please contact customer service if the problem persists.
An error message indicates insufficient
volume of blood sample for the test.
Follow the instructions and try again with a new test strip,
then applying a sufficient blood sample to the test strip.
Please contact customer service if the problem persists.
An error message indicates a problem with
the meter.
Remove batteries and wait for 1 minute. Reinstall
batteries to see if meter is working properly. Please
contact customer service if the problem persists.
Trouble Shooting
Other problems which may occur
Action
A test strip has not been inserted into the meter
properly.
Review the instructions and re-insert a test strip
correctly.
Defective test strip.
Replace with a new test strip.
A test strip remains in the test port for more than 2
minutes before testing.
Review the instructions and re-insert a test strip
correctly.
LCD display on the meter is blank when trying to
perform a test.
Please contact customer services for assistance.
The meter does not function after new batteries are
installed.
Remove batteries and wait for 1 minute. Reinstall
batteries to see if meter is working properly.
33
Specifications
Operation Temperature
Operation Humidity
Hematocrit
Test Sample
10 ~ 90% RH
10 ~ 65%
Capillary Whole Blood(fingertip, palm, and forearm)
Sample Volume
0.7 µL
Measuring Unit
mg/dL
Measuring Range
Test Time
Memory Capacity
Average
External Output
Power supply
34
50°F ~ 104°F (10°C ~ 40°C)
20 ~ 600 mg/dL
5 seconds countdown
500 most recent results
7/14/30 days average
USB interface
2 AAA batteries
Battery Life
Approximately 1000 tests
Dimension
106L x 66W x 20H mm
Weight
70 g without batteries
Note: Please refer to the Test Strip Insert for
the performance of system accuracy and
precision.
The Meter meets the electromagnetic
compatibility requirements as per IEC
60601-1-2:2014 and EN 60601-1-2:2015.
Caution: Do not use the meter close to the
electronic equipment which is a source of
strong electromagnetic radiation, which may
interfere with proper operation of meter.
Meter Storage
˙Transport and store at temperature -4°F ~ 122 °F (-20°C ~ 50°C), less than 90% RH.
˙Precision instrument, do not drop or crush when being transported.
Icon Description
Temperature limitation
Manufacturer
Batch code
In vitro diagnostic medical device
Use by
Consult instructions for use
Do not reuse
Sufficient for
Serial Number
Catalogue number
Caution
Control
35
Service and Warranty
IMPORTANT
˙Tyson Bio HT100-C Blood Glucose Glucose Meter, Tyson Bio HT100-C Test Strip and Tyson Bio HT100-C Control Solution
are in conformity with the CFR, Title 21 and IVDD 98/79/EC.
˙Tyson Bio HT100-C Blood Glucose Monitoring System manufacturer warranty is valid only when used properly with in the
guidelines of this User Manual provided.
˙The Lancing device and Lancets are in conformity with the CFR, Tiltle 21 and MDD 93/42/EEC.
Manufacturer Warranty
˙Tyson Bioresearch Inc. offers 3 years guarantee on this product. Our company shall repair or replace any Tyson Bio
HT100-C Blood Glucose Monitoring System found defective with a new one.
˙This warranty does not apply to the performance of a Tyson Bio HT100-C Blood Glucose Monitoring System that has been
accidentally damaged, altered, misused, tampered with or abused in anyway. In no event shall our company be liable to
the purchaser or any other person for any incidental, consequential, or punitive damages arising from or in anyway
connected with the purchase or operation of Tyson Bio HT100-C Blood Glucose Monitoring System.
˙For manufacturer warranty services, purchaser must contact Tyson Bioresearch, Inc. for help.
36
Notice
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void
the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
˙Reorient or relocate the receiving antenna.
˙Increase the separation between the equipment and receiver.
˙Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
˙Consult the dealer or an experienced radio/TV technician for help.
37
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation of the
device.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
38
Manufacturer of Blood Glucose Meter, Test Strip and Control Solution
Tyson Bioresearch, Inc.
5F., No. 16, 18, 20, 22, Kedong 3rd Rd.,
Zhunan Township, Miaoli County 35053, Taiwan
+886-37-585998
www.tysonbio.com
Customer Service
U.S.A. +1-800-948-3894
Taiwan +886-37-585998
24 hours a day, 7 days a week
GMT+8, 8:30 ~ 17:30, Monday ~ Friday
When you call our customer service, please have all components of the product available. This will allow us to answer your
questions with speed and efficiency.
Manufacturer of Lancet and Lancing Device
Shandong Lianfa Medical Plastic Products Co., Ltd.
No.1 Shuangshan Sanjian Road 250200 Zhangqiu City, Jinan, Shandong PEOPLE’S REPUBLIC OF CHINA
SteriLance Medical (Suzhou) Inc.
No.68 Litanghe Road,Xiangcheng Suzhou, Jiangsu 215133 P.R.China
39

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.6-c143 79.161210, 2017/08/11-10:28:36
Create Date                     : 2018:01:17 13:08:23+09:00
Metadata Date                   : 2018:01:17 13:08:24+08:00
Modify Date                     : 2018:01:17 13:08:24+08:00
Creator Tool                    : Adobe Illustrator CC 22.0 (Windows)
Thumbnail Width                 : 36
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 4895 bytes, use -b option to extract)
Instance ID                     : uuid:dc1f7b06-fd1d-41b3-9274-6b418fd91d87
Original Document ID            : xmp.did:7802FC91387AE11183C8CDD1A970ED67
Document ID                     : xmp.did:a8a4380d-5423-6640-96ab-29fa08b12bc9
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:e1588b98-060a-471e-8a1c-b4e33056bea5
Derived From Document ID        : xmp.did:07de6bc7-da31-c24a-9c65-187fbd399c52
Derived From Original Document ID: xmp.did:7802FC91387AE11183C8CDD1A970ED67
Derived From Rendition Class    : proof:pdf
History Action                  : converted, saved, saved
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh), Adobe Illustrator CC 2015 (Macintosh), Adobe Illustrator CC 22.0 (Windows)
History Changed                 : /, /, /
History When                    : 2016:07:19 11:28:27+08:00, 2016:10:21 15:17:52+08:00, 2018:01:17 13:08:12+08:00
History Instance ID             : xmp.iid:86ac97ae-b4dc-48c0-87ee-133816d6c347, xmp.iid:a8a4380d-5423-6640-96ab-29fa08b12bc9
Manifest Link Form              : EmbedByReference, EmbedByReference, EmbedByReference
Manifest Reference File Path    : vvnI5J.tif, vvnI5J.tif, 50H_K.psd
Ingredients File Path           : vvnI5J.tif, vvnI5J.tif, 50H_K.psd
Format                          : application/pdf
Title                           : HT100_C_Manual_LAY_FDA_AF004-0027000N_180117
Producer                        : Adobe PDF library 15.00
Trapped                         : False
N Pages                         : 1
Has Visible Transparency        : True
Has Visible Overprint           : True
Max Page Size W                 : 139.999999
Max Page Size H                 : 90.000032
Max Page Size Unit              : Millimeters
Font Name                       : Arial-BoldItalicMT, ArialMT, Arial-BoldMT, BakerSignetBT-Roman, MyriadPro-Regular, MyriadPro-It, MyriadPro-Semibold, MyriadPro-SemiboldIt, MyriadPro-Bold, MyriadPro-BoldIt, MyriadPro-Black, MyriadPro-BlackIt, AdobeMingStd-Light
Font Family                     : Arial, Arial MT, Arial MT, BakerSignet BT, Myriad Pro, Myriad Pro, Myriad Pro, Myriad Pro, Myriad Pro, Myriad Pro, Myriad Pro, Myriad Pro, Adobe 明體 Std
Font Face                       : Bold Italic, Regular, Bold, Roman, Regular, Italic, Semibold, Semibold Italic, Bold, Bold Italic, Black, Black Italic, L
Font Type                       : Open Type, Open Type, Open Type, TrueType, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type
Font Version                    : Version 5.21, 001.000, 001.001, mfgpctt-v1.57 Friday, February 19, 1993 3:30:24 pm (EST), Version 2.006;PS 002.000;Core 1.0.38;makeotf.lib1.6.6565, Version 2.006;PS 002.000;Core 1.0.38;makeotf.lib1.6.6565, Version 2.006;PS 002.000;Core 1.0.38;makeotf.lib1.6.6565, OTF 1.006;PS 001.000;Core 1.0.23;hotunix 1.28, Version 2.006;PS 002.000;Core 1.0.38;makeotf.lib1.6.6565, OTF 1.006;PS 001.000;Core 1.0.23;hotunix 1.28, OTF 1.006;PS 001.000;Core 1.0.23;hotunix 1.28, OTF 1.006;PS 001.000;Core 1.0.23;hotunix 1.28, Version 6.008;PS 6.001;hotconv 1.0.67;makeotf.lib2.5.33168
Font Composite                  : False, False, False, False, False, False, False, False, False, False, False, False, False
Font File Name                  : arialbi_2.ttf, ArialMT_0.otf, Arial-BoldMT_0.otf, BAKRSIGN_0.TTF, MyriadPro-Regular_0.otf, MyriadPro-It_0.otf, MyriadPro-Semibold_0.otf, MyriadPro-SemiboldIt_0.otf, MyriadPro-Bold_0.otf, MyriadPro-BoldIt_0.otf, MyriadPro-Black_0.otf, MyriadPro-BlackIt_0.otf, AdobeMingStd-Light_0.otf
Plate Names                     : Cyan, Magenta, Yellow, Black, PANTONE Cool Gray 11 C
Swatch Group Name               : 預設色票群組
Swatch Group Type               : 0
Swatch Colorant Swatch Name     : PANTONE Orange 021 C, PANTONE Cool Gray 11 C, C=50 M=0 Y=90 K=0, C=10 M=100 Y=100 K=0, C=0 M=0 Y=0 K=60 1, C=0 M=0 Y=0 K=80
Swatch Colorant Type            : SPOT, SPOT, PROCESS, PROCESS, PROCESS, PROCESS
Swatch Colorant Tint            : 100.000000, 100.000000, 100.000000, 100.000000
Swatch Colorant Mode            : CMYK, Lab, CMYK, CMYK, CMYK, CMYK
Swatch Colorant Cyan            : 0.000000, 50.000000, 10.000000, 0.000000, 0.000000
Swatch Colorant Magenta         : 80.000001, 0.000000, 100.000000, 0.000000, 0.000000
Swatch Colorant Yellow          : 100.000000, 89.999998, 100.000000, 0.000000, 0.000000
Swatch Colorant Black           : 0.000000, 0.000000, 0.000000, 60.000000, 80.000000
Swatch Colorant L               : 36.470600
Swatch Colorant A               : 0
Swatch Colorant B               : -3
Page Count                      : 42
Creator                         : Adobe Illustrator CC 22.0 (Windows)

EXIF Metadata provided by EXIF.tools