Tait TBAB1A Base Station Tranceiver User Manual Exhibit D Users Manual per 2 1033 c3

Download:
Mirror Download [FCC.gov]
Document ID	502237
Application ID	rrPHNLWihIwQCtapP4hXPQ==
Document Description	Exhibit D Users Manual per 2 1033 c3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	68.65kB (858095 bits)
Date Submitted	2004-12-30 00:00:00
Date Available	2004-12-29 00:00:00
Creation Date	2004-12-20 16:57:35
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2004-12-20 16:57:35
Document Title	Exhibit D Users Manual per 2 1033 c3

Appendix 1: 12V PA
Boost Regulator Circuit Description
This section provides a brief description of the circuitry on the boost
regulator board. Figure 1.1 below shows the configuration for a 5W or
50W PA, along with the main inputs and outputs for power, RF and control
signals. Note that the 60W board is only fitted to the 50W PA. The circuit
description for the rest of the PA is provided in the “Circuit Description”
chapter.
Figure 1.1
5W or 50W PA high level block diagram
12VDC
I/P
12VDC O/P
(Reciter)
Boost Regulator
28VDC
RF I/P +
PA Key
6W
Board
DC
System
Control
Bus
28VDC
60W
Board
RF
Control &
Monitor
RF O/P
RF
Low-Pass
Filter
Directional
Coupler
Board
Control &
Monitor
Control &
Monitor
Control Board
Ambient Air
Temperature
Sensor
Board
The boost regulator board accepts an input of 12VDC nominal. The input
is firstly fed through the DC input filter, and is then fed through an output
filter to provide the 12VDC (nominal) output for the reciter. The output
from the DC input filter is also fed to the power stage where the voltage is
boosted to 28VDC, and is then fed through an output filter to provide the
28VDC output for the PA circuit boards.
The battery control circuitry monitors the DC input voltage from the
battery. Protection is provided against the wrong input voltage being
supplied. The battery control circuitry also prevents deep discharge of the
battery.
TB8100 Installation and Operation Manual
© Tait Electronics Limited December 2004
Appendix 1: 12V PA
Overview of Inputs and Outputs
This section identifies the main input and output connections for the
TB8100 BSS with 12V PA. Figure 1.2 below identifies the connections at
the front of the base station, and Figure 1.3 on page iii identifies those at the
rear. Refer to the “Connection” chapter for more details.
Figure 1.2
5W or 50W base station inputs and outputs - front view
c d e
PA
RF input from reciter
12VDC low current output for reciter
RF output to PA
reciter
terminating circuitry for system control bus
system control bus
DC output (for optional reciter fan only)
12VDC low current input from PA
Important
ii
h g
Appendix 1: 12V PA
The system control bus terminating circuitry board must be
connected to the system control bus at all times. If the
board is disconnected, the state of much of the bus will be
undefined. This may cause corrupted data to be present on
the bus when the reciter reads the states of the switches on
the control panel. This in turn may result in random actuations of microphone PTT, carrier, or speaker key, causing
the BSS to transmit or the speaker to be actuated incorrectly.
TB8100 Installation and Operation Manual
© Tait Electronics Limited December 2004
Figure 1.3
5W or 50W base station inputs and outputs - rear view
b c
reciter
system interface connector
external reference frequency input
12VDC input
Power Saving control input
PA
RF output
RF input
auxiliary DC input for system interface
subrack ground connector
DC Power
The TB8100 12V PA is designed to accept a nominal 12VDC input with
negative ground. There is a minimum DC start-up threshold to prevent
damaging a battery which has little capacity left.
You must connect the DC supply from the battery to the PA via a fuse or
DC-rated circuit breaker with the appropriate rating, as shown in the table
below. The DC input leads should be of a suitable gauge to ensure less than
0.2V drop at maximum load over the required length of lead.
Nominal Supply
Voltage
12VDC
Input Voltage
Range
Circuit Breaker/
Fuse Rating
10.6VDC to 16.8VDC 20A
Recommended
Wire Gaugea
2AWG / 35mm2
a. For a length of 1.5m to 2m (5ft to 6.5ft) (typical).
TB8100 Installation and Operation Manual
© Tait Electronics Limited December 2004
Appendix 1: 12V PA
iii
Figure 1.4
Recommended DC power connection
Circuit Breaker
or Fuse
PMU
Battery
The pin allocations for the 2-way DC input connector are shown below.
Pin
Description
+V input
ground
2-way connector - external view
iv
Appendix 1: 12V PA
TB8100 Installation and Operation Manual
© Tait Electronics Limited December 2004

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:12:20 16:57:35
Producer                        : Acrobat Distiller 4.05 for Windows
Modify Date                     : 2004:12:20 16:57:35+14:00
Page Count                      : 4

EXIF Metadata provided by EXIF.tools