Tatung KHA01651B DIGITAL ENTERTAINMENT CENTER User Manual USERS MANUAL
Tatung Company DIGITAL ENTERTAINMENT CENTER USERS MANUAL
Tatung >
USERS MANUAL
Digital Entertainment Center KHA-01651B Set-Up-Guide Rear Panel 11 13 15 Unpack the box WIFI AAA AAA Set Top Box DC-IN 12V Remote Control HDMI OUT SPDIF OUT Set-Up-Guide Component Cable Adapter Audio/Video Cable 7 S-Video Cable 8 Power Cord AUDIO & VIDEO IN Antenna Cable WIFI Antenna DC IN 12V HDMI OUT Componert (VIDEO OUT) COMPOSTIE(VIDEO OUT) S-VIDEO(VIDEO OUT) 10 11 12 10 12 14 AUDIO OUT(Left) AUDIO OUT(Right) COAXIAL(SPDIF OUT) OPTICAL(SPDIF OUT) AUDIO IN(Left) AUDIO IN(Right) 16 17 13 14 15 16 17 COMPOSTIE(VIDEO IN) S-VIDEO(VIDEO IN) LAN USB 2.0x2 ANT 1 IN Features Front Panel Audio Out Analog Audio Out (Audio Cable) & S/PDIF Out (Digital Optical Cable) WIFI DC-IN 12V Indicators 1 Power Button 2 Navigation Button 3 Menu Button HDMI OUT SPDIF OUT AUDIO & VIDEO IN :Press Power Red / Blue light illuminates when STB is on and sending a signal to the TV. :Press Up, Down, Left, Right to access and navigate menu items. Press OK to confirm. :Press Button to display the menu. Digital Coaxial Cable OPTICAL Audio Cable Digital Optical Cable Optical Fiber COAXIAL Connector S-VIDEO IN VIDEO IN AUDIO IN(Fornt Left Right ) MMC/SD 8 MD/CompactFlash I/II 9 Memory Stick/Pro/Duo 10 USB 2.0 10 Audio R Amplifier Amplifier 4 Plug in Power Cord and Turn Power On Video Out Connecting Analog AV WIFI DC-IN 12V HDMI OUT SPDIF OUT AUDIO & VIDEO IN WIFI DC-IN 12V HDMI OUT SPDIF OUT AUDIO & VIDEO IN Y/Pb/Pr Cable Note: Make sure the TV indicator is on before you start to use STB. The POWER button on the TV remote turns the TV on and off. The POWER button on the TV remote puts the STB in and out of standby state. Installing Batteries or AAA Pr Pb TV/VCR/DVR/MCPC/PVR Connecting Analog AV & Connecting Digital AV (HDMI) AAA Remote Control bottom side of view Safety Information Before you getting started, please read the important safety information below. AC Power Safety Warnings WIFI DC-IN 12V HDMI OUT SPDIF OUT The power supply is pre-set for the country/region in which you purchased DSTB (Digital Set Top Box). If you move to another country/region, please make sure you check its voltage requirements before plugging DSTB into an AC power outlet. Install the DSTB near an AC outlet. The AC power cord is DSTB's main AC disconnecting device and must be easily accessible at all times. For your safety, the power cord provided with your system has a grounded plug. Always use the power cord with a properly grounded wall outlet to avoid the risk of electrical shock. AUDIO & VIDEO IN S-Video Cable HDMI Cable Conventions used in this manual TV/VCR/DVR/MCPC/PVR VIDEO DEVICE WIFI HDMI OUT SPDIF OUT AUDIO & VIDEO IN to Router or ADSL WIFI Digital signals are received with the antenna cable connection. CAUTION: Information to prevent damage to the components when trying to complete a task. To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. DO NOT OPEN THE CHASSIS ANY TIME. Operation Safety Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your Service Provider immediately. To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry. Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet. Place the product on a stable surface. Slots and openings are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. This product should never be placed near or over a radiator or heat register. Antenna coaxial screen must be probably earthed. Federal Communication Commission Interference Statement Local Area Network (LAN) DC-IN 12V WARNING: Information to prevent injury to yourself when trying to complete a task. Electrical Safety or Ethernet LAN cable This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 2 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:c15ffad2-29a6-4ff0-b9af-703689700b37 Modify Date : 2007:06:08 10:02:09+08:00 Create Date : 2007:06:08 09:48:00+08:00 Metadata Date : 2007:06:08 10:02:09+08:00 Document ID : uuid:0c980270-bac5-4d11-aab7-b7b7fe3cca8c Format : application/pdf Creator : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 6.0 (Windows)EXIF Metadata provided by EXIF.tools