Taylor Freezer 345 346 349 355 Users Manual

345346349355 to the manual e29671f1-cc81-466d-929d-4491509fe4ad

: Taylor Taylor-Taylor-Freezer-345-346-349-355-Users-Manual-449397 taylor-taylor-freezer-345-346-349-355-users-manual-449397 taylor pdf

Open the PDF directly: View PDF .
Page Count: 87

OPERATOR’S

MANUAL

Model 345/346/349/355

Slush Freezers

Original Operating Instructions

039710- M

6/19/01 (Original Publication)

Updated 11/22/13

Complete this page for quick reference when service is required:

Taylor Distributor:

Address:

Phone:

Fax:

E- mail:

Service:

Parts:

Date of Installation:

Information found on the data label:

Model Number:

Serial Number:

Electrical Specs: Voltage Cycle

Phase

Maximum Fuse Size: A

Minimum Wire Ampacity: A

E2001 Carrier Commercial Refrigeration, Inc.

039710- M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work

may be a violation of Copyright Law of the United States of America and other countries, could result in the

awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further

civil and criminal penalties.

All rights reserved.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

Table of Contents Models 345, 346, 349, 355

Table of Contents

Section 1 To the Installer 1............................................

Air Cooled Units 1.......................................................

Water Cooled Refrigeration Units (Water Cooled Units Only) 2................

Water Connections 2....................................................

Electrical Connections 2.................................................

Syrup System Connections 4.............................................

Section 2 To the Operator 7...........................................

Section 3 Safety 8....................................................

Section 4 Operator Parts Identification 10...............................

Model 345 10............................................................

Model 346 11............................................................

Model 349 12............................................................

Model 355 13............................................................

Door Assembly 14.......................................................

Accessories 15..........................................................

Section 5 Important: To the Operator 16.................................

Symbol Definitions 16....................................................

Control Switch 16........................................................

Liquid Crystal Display 17..................................................

Operational Mode Display 17..............................................

Operator Menu Display 17................................................

Syrup Out Indicator 22....................................................

CO2 Out Indicator 23.....................................................

Water Out Indicator 23....................................................

Audio Alarm Silencer 23..................................................

Product Light 23.........................................................

Sampling Valve 23.......................................................

Daily Procedures 23......................................................

Section 6 Operating Procedures 24.....................................

Assembly 24............................................................

Sanitizing 29............................................................

Priming/Brixing 33........................................................

90 Day Closing Procedure 35..............................................

Draining Product From the Freezing Cylinder 35.............................

Cleaning 35.............................................................

Disassembly 36..........................................................

Brush Cleaning 36.......................................................

Models 345, 346, 349, 355 Table of Contents

Table of Contents - Page 2

Section 7 Important: Operator Checklist 38..............................

During Cleaning and Sanitizing 38.........................................

Troubleshooting Bacterial Count 38........................................

Regular Maintenance Checks 38...........................................

Winter Storage 39........................................................

Section 8 Troubleshooting Guide 40....................................

Section 9 Parts Replacement Schedule 42...............................

Section 10 Limited Warranty on Equipment 43............................

Section 11 Limited Warranty on Parts 45.................................

Section 12 Parts List 48.................................................

Wiring Diagrams 70......................................................

Note: Continuing research results in steady improvements; therefore, information

in this manual is subject to change without notice.

Note: Only instructions originating from the factory or its authorized translation

representative(s) are considered to be the original set of instructions.

E2001 Carrier Commercial Refrigeration, Inc.

(Updated November, 2013)

039710- M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work

may be a violation of Copyright Law of the United States of America and other countries, could result in the

awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further

civil and criminal penalties.

All rights reserved.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

1

Models 345, 346, 349, 355 To the Installer

131122

Section 1 To the Installer

The following information has been included in the

manual as safety and regulatory guidelines. For

complete installation instructions, please see the

Installation Checklist.

Installer Safety

In all areas of the world, equipment should be

installed in accordance with existing local codes.

Please contact your local authorities if you have any

questions.

Care should be taken to ensure that all basic safety

practices are followed during the installation and

servicing activities related to the installation and

service of Taylor equipment.

SOnly authorized Taylor service personnel

should perform installation and repairs on

the equipment.

SAuthorized service personnel should consult

OSHA Standard 29CFRI910.147 or the

applicable code of the local area for the

industry standards on lockout/tagout

procedures before beginning any installation

or repairs.

SAuthorized service personnel must ensure

that the proper PPE is available and worn

when required during installation and

service.

SAuthorized service personnel must remove

all metal jewelry, rings, and watches before

working on electrical equipment.

The main power supply(s) to the freezer must

be disconnected prior to performing any repairs.

Failure to follow this instruction may result in personal

injury or death from electrical shock or hazardous

moving parts as well as poor performance or damage

to the equipment.

Note:Allrepairsmustbeperformedbyan

authorized Taylor Service Technician.

This unit has many sharp edges that can

cause severe injuries.

Site Preparation

Review the area where the unit will be installed before

uncrating the unit. Make sure that all possible hazards

to the user and the equipment have been addressed.

Air Cooled Units

Air cooled units require 6” (152 mm) minimum air

space around all sides. Failure to allow adequate

clearance can reduce the refrigeration capacity of the

freezer and possibly cause permanent damage to the

compressor(s).

For Indoor Use Only: This unit is designed to operate

indoors, under normal ambient temperatures of

70_-75_F(21_-24_C). The freezer has successfully

performed in high ambient temperatures of

104_(40_C) at reduced capacities.

This unit must NOT be installed in an area

where a water jet or hose can be used. NEVER use a

water jet or hose to rinse or clean the unit. Failure to

follow this instruction may result in electrocution.

This unit must be installed on a level surface

to avoid the hazard of tipping. Extreme care should be

taken in moving this equipment for any reason. Two or

more persons are required to safely move this unit.

Failure to comply may result in personal injury or

equipment damage.

Uncrate the unit and inspect it for damage. Report any

damage to your Taylor Distributor.

This piece of equipment is made in the USA and has

USA sizes of hardware. All metric conversions are

approximate and vary in size.

2Models 345, 346, 349, 355To the Installer

120828

Water Cooled Refrigeration Units

(Water Cooled Units Only)

Failure to use adequate size water lines may cause the

unit to go off on high head pressure and shut down.

Depending on local water conditions, it may be

advisable to install a water strainer to prevent foreign

substances from clogging the automatic water valve.

There are two water “in” connections and one water

“out” line connection. DO NOT install a hand shut-off

valve on the water “out” line! Water should always

flow in this order: first, through the automatic water

valve; second, through the condenser; and third,

through the outlet fitting to an opentrapdrain.

IMPORTANT: Water pressures are pre-set at the

factory. Do not adjust the water. Improper water

adjustments may cause operation discrepancies.

A back flow prevention device is required

on the incoming water connection side. Please

refer to the applicable National, State, and local codes

for determining the proper configuration.

Water Connections

An adequate cold water supply must be provided

with a hand shut-off valve. On the back of the unit, a

3/8” (9.5 mm) M.F.L. water connection has been

provided for easy hook-up. A flexible line is

recommended, if local codes permit. A minimum of

25 psi water pressure is required to avoid having the

unit cut out the low water pressure switch. A booster

pump must be provided if this pressure is not

available.

Note: Water lines beyond 200 ft. (61 m) require 1/2”

(13 mm) water lines.

INSTALL POTABLE WATER CONNECTION

WITH ADEQUATE BACK-FLOW

PROTECTION TO COMPLY WITH

APPLICABLE NATIONAL, STATE AND

LOCAL CODES.

It is always a good practice to have a filter system to

improve the quality of the water and to avoid

clogging the operating components.

IMPORTANT: The water filter (064422- SER) must

be thoroughly flushed with water before connecting it

to the machine. This removes carbon particles that

could clog the flow control. To flush the filter,

connect the inlet end of the filter to the water supply.

Position the outlet end of the filter over an empty

pail. Open the water supply. Allow water to flow

through the filter until the water exiting the filter is

clear. Close the water supply. Attach the outlet end

of the filter to the machine. Reopen the water

supply.

Figure 1

Electrical Connections

In the United States, this equipment is intended to be

installed in accordance with the National Electrical

Code (NEC), ANSI/NFPA 70- 1987. The purpose of

the NEC code is the practical safeguarding of persons

and property from hazards arising from the use of

electricity. This code contains provisions considered

necessary for safety. Compliance therewith and

proper maintenance will result in an installation

essentially free from hazard! In all other areas of the

world, equipment should be installed in accordance

with the existing local codes. Please contact your local

authorities.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

Each unit requires one power supply for each data

label on the unit. Check the data label(s) on the freezer

for branch circuit overcurrent protection or fuse, circuit

ampacity, and other electrical specifications. Refer to

the wiring diagram provided inside of the control box

for proper power connections.

3

Models 345, 346, 349, 355 To the Installer

120828

CAUTION: THIS EQUIPMENT MUST BE

PROPERLY GROUNDED! FAILURE TO DO SO

CAN RESULT IN SEVERE PERSONAL INJURY

FROM ELECTRICAL SHOCK!

DO NOT operate this freezer with larger fuses

than specified on the unit data label. Failure to follow

this instruction may result in electrocution or damage

to the machine.

This unit is provided with an equipotential

grounding lug that is to be properly attached to the rear

of the frame by the authorized installer. The installation

location is marked by the equipotential bonding

symbol (5021 of IEC 60417-1) on both the removable

panel and the equipment’s frame.

Stationary appliances which are not equipped

with a power cord and a plug or another device to

disconnect the appliance from the power source must

have an all-pole disconnecting device with a contact

gap of at least 3 mm installed in the external

installation.

Appliances that are permanently connected to

fixed wiring and for which leakage currents may

exceed 10 mA, particularly when disconnected or not

used for long periods, or during initial installation, shall

have protective devices such as a GFI, to protect

against the leakage of current, installed by the

authorized personnel to the local codes.

Supply cords used with this unit shall be

oil-resistant, sheathed flexible cable not lighter than

ordinary polychloroprene or other equivalent synthetic

elastomer-sheathed cord (Code designation 60245

IEC 57) installed with the proper cord anchorage to

relieve conductors from strain, including twisting, at

the terminals and protect the insulation of the

conductors from abrasion.

Beater Rotation

Beater rotation must be clockwise as viewed

looking into the freezing cylinder.

Note: The following procedures should be

performed by a trained service technician.

To correct the rotation on a three- phase unit,

interchange any two incoming power supply lines at

freezer main terminal block only.

To correct rotation on a single- phase unit, change the

leads inside the beater motor. (Follow the diagram

printedonthemotor.)

Initial Freezing Cylinder Cleaning

Due to the types of products used in FCB equipment,

it is imperative that the freezing cylinder and the inlet

tube be thoroughly brush cleaned, rinsed, and

sanitized before running any product.

Prepare a cleaning solution, using 2 oz. of liquid

detergent in 2 gallons of warm water. Using this

solution, brush clean the freezing cylinder and the inlet

tube. Rinse the freezing cylinder and the inlet tube with

clean water and then sanitize, using the sanitizing

procedures outlined in this Operator Manual, starting

on page 29.

Refrigerant

In consideration of our environment, Taylor

uses only earth friendly HFC refrigerants. The HFC

refrigerant used in this unit is R404A. This refrigerant

is generally considered non-toxic and non-flammable,

with an Ozone Depleting Potential (ODP) of zero (0).

However, any gas under pressure is potentially

hazardous and must be handled with caution.

NEVER fill any refrigerant cylinder completely with

liquid. Filling the cylinder to approximately 80% will

allow for normal expansion.

4Models 345, 346, 349, 355To the Installer

131122

Use only R404A refrigerant that conforms to

the AHRI standard 700 specification. The use of any

other refrigerant may expose users and operators to

unexpected safety hazards.

Refrigerant liquid sprayed onto the skin may

cause serious damage to tissue. Keep eyes and skin

protected. If refrigerant burns should occur, flush

immediately with cold water. If burns are severe, apply

ice packs and contact a physician immediately.

Taylor reminds technicians to be cautious of

government laws regarding refrigerant recovery,

recycling, and reclaiming systems. If you have any

questions regarding these laws, please contact the

factory Service Department.

WARNING: R404A refrigerant used in

conjunction with polyolester oils is extremely moisture

absorbent. When opening a refrigeration system, the

maximum time the system is open must not exceed 15

minutes. Cap all open tubing to prevent humid air or

water from being absorbed by the oil.

Syrup System Connections

1. Water pipe connections and fixtures directly

connected to a potable water supply shall be

sized, installed and maintained according to

federal, state and local laws.

2. Hook up cold water supply to freezer to supply

water to the carbonator. A minimum of 21 PSI

of water pressure is required at the low

pressure switch. The low pressure switch will

cause the entire freezer to shut down if the

water pressure drops below 7 PSI for longer

than one minute.

The water regulator should be set at 35 PSI.

When the power switch is turned on the water

pump will immediately activate to maintain water

pressure.

3. Electrical Hook-Up

a. One power cord.

b. Refer to the data label.

c. Be sure all control switches on the front panel

are in the “OFF” position.

d. The freezer must be properly grounded.

4. A harness with three nylobrade tubes feeds

through the base pan and exits the rear of the

freezer. (The Model 355 is equipped with four

tubes.)

a. Connect the CO2line to the CO2regulator

that is closest to the CO2tank (primary

regulator). This line will supply CO2to the

freezer.

Figure 2

b. Connect the #1 line to the syrup tank for the

left side of the freezer as viewed from the

front of the machine. This line will supply

syrup to the left syrup sentry.

Note: For Bag-in-Box units (BIB), connect the #1 line

to the Bag-In-Box instead of the syrup tank.

Figure 3

c. Connect the #2 line to the syrup tank (or the

Bag-in-Box) for the right side of the freezer.

This line will supply syrup to the right syrup

sentry.

5

Models 345, 346, 349, 355 To the Installer

d. Connect the #4 line on the Model 355 to the

water regulator on the remote carbonator.

This line monitors the water pressure

supplied to the unit.

5. There are two spare CO2lines provided. Use

one of the spare CO2lines to connect one end

to the individual regulator (secondary regulator)

and the other end to the first syrup tank. Use

the other spare CO2line to connect the CO2to

the second syrup tank.

Figure 4

Note: For Bag-in-Box units, connect the CO2lines to

the Bag-in-Box pumps instead of the syrup tanks.

Figure 5

6. Set the primary regulator on the CO2tank to 90

PSI (6.2 BAR).

Figure 6

7. Set the secondary regulator on the CO2tank to

60 PSI (4.1 BAR) for the syrup tanks or the BIB

pumps.

Figure 7

8. Turn the cold water supply on.

9. Check for CO2leaks. This can be done by

closingthevalveonthetopoftheCO

2tank.

Watch the high pressure gauge; it should hold

pressure. If it does not, there is a CO2leak.

Use a soap solution to locate and repair the

leak.

6Models 345, 346, 349, 355To the Installer

10. For Bag-in-Box syrup delivery system, connect

thetwospareCO

2lines from the secondary

regulator to each “Gas In” fitting on the pumps.

Set secondary regulator pressure to 60 PSI

(4.1 BAR) depending on the length of syrup line

run to the unit.

Important: Ensure that the Bag-in-Box switch is

enabled.

11. The CO2regulator assembly (primary regulator)

inside the freezer should be set at 60 PSI (4.1

BAR). The secondary regulator, located inside

the freezer just behind the primary regulator,

canbeadjustedfrom20to25PSI.(Thefactory

recommendation is 20 PSI.) Increasing the

pressure from 20 PSI will increase the overrun.

You should always stay within the 20 to 25 PSI

range as the gauge reflects the pressure in the

hopper and barrel. The setting will be

determined by the desired overrun and the

syrup used.

12. The CO2low pressure switch requires at least

74 PSI before the freezer will start. It is set to

cut out at 60 PSI and in at 74 PSI.

13. The pressure relief valve on the hopper cover is

set to relieve at 30 PSI in case of excess

pressure in the hopper.

14. There are check valves in the CO2, syrup, and

water lines to prevent any back flow of soda

water, product, or CO2.

15. The CO2solenoids which supply CO2to the

hoppers are wired to provide CO2in all control

settings except “DEFROST” and “OFF”.

7

Models 345, 346, 349, 355 To the Operator

131122

Section 2 To the Operator

The freezer(s) you have purchased has been carefully

engineered and manufactured to give you dependable

operation.

This unit(s), when properly operated and cared for, will

produce a consistent quality product. Like all

mechanical products, this machine will require

cleaning and scheduled maintenance. A minimum

amount of care and attention is necessary if the

operating procedures outlined in this manual are

followed closely.

This Operator’s Manual should be read before

operating or performing any maintenance on your

equipment.

Your freezer will NOT eventually compensate and

correct for any errors during the set-up or filling

operations. Thus, the initial assembly and priming

procedures are of extreme importance. It is strongly

recommended that all personnel responsible for the

equipment’s operation study these procedures

together in order to be properly trained and to make

sure that no misunderstandings exist.

In the event you should require technical assistance,

please contact your local authorized Taylor Distributor

for service.

Note: Your Taylor warranty is valid only if the parts are

authorized Taylor parts, purchased from the local

authorized Taylor Distributor, and only if all required

service work is provided by an authorized Taylor

service technician. Taylor reserves the right to deny

warranty claims on units or parts if non- Taylor

approved parts or incorrect refrigerant were installed

in the unit, system modifications were performed

beyond factory recommendations, or it is determined

that the failure was caused by abuse, misuse, neglect,

or failure to follow all operating instructions. For full

details of your Taylor Warranty, please see the Limited

Warranty section in this manual.

Note: Constant research results in steady

improvements; therefore, information in this

manual is subject to change without notice.

If the crossed out wheeled bin symbol is

affixed to this product, it signifies that this product is

compliant with the EU Directive as well as other similar

legislation in effect after August 13, 2005. Therefore,

it must be collected separately after its use is

completed, and cannot be disposed as unsorted

municipal waste. The user is responsible for returning

the product to the appropriate collection facility, as

specified by your local code.

For additional information regarding applicable local

laws, please contact the municipal facility and/or local

distributor.

Compressor Warranty Disclaimer

The refrigeration compressor(s) on this unit are

warranted for the term stated in the Limited Warranty

section in this manual. However, due to the Montreal

Protocol and the U.S. Clean Air Act Amendments of

1990, many new refrigerants are being tested and

developed, thus seeking their way into the service

industry. Some of these new refrigerants are being

advertised as drop- in replacements for numerous

applications. It should be noted that in the event of

ordinary service to this unit’s refrigeration system,

only the refrigerant specified on the affixed data

label should be used. The unauthorized use of

alternate refrigerants will void your Taylor compressor

warranty. It is the unit owner’s responsibility to make

this fact known to any technician he employs.

It should also be noted that Taylor does not warrant the

refrigerant used in its equipment. For example, if the

refrigerant is lost during the course of ordinary service

to this machine, Taylor has no obligation to either

supply or provide its replacement either at billable or

unbillable terms. Taylor does have the obligation to

recommend a suitable replacement if the original

refrigerant is banned, obsoleted, or no longer available

during the five year warranty of the compressor.

Taylor will continue to monitor the industry and test

new alternates as they are being developed. Should a

new alternate prove, through our testing, that it would

be accepted as a drop-in replacement, then the above

disclaimer would become null and void. To find out the

current status of an alternate refrigerant as it relates to

your compressor warranty, call the local Taylor

Distributor or the Taylor Factory. Be prepared to

provide the Model/Serial Number of the unit in

question.

8Models 345, 346, 349, 355Safety

131122

Section 3 Safety

We at Taylor are concerned about the safety of the

operator when he or she comes in contact with the

freezer and its parts. Taylor has gone to extreme

efforts to design and manufacture built- in safety

features to protect both you and the service technician.

As an example, warning labels have been attached to

the freezer to further point out safety precautions to the

operator.

IMPORTANT - Failure to adhere to the

following safety precautions may result in severe

personal injury or death. Failure to comply with

these warnings may damage the machine and its

components. Component damage will result in

part replacement expense and service repair

expense.

DO NOT operate the freezer without reading

this Operator Manual. Failure to follow this instruction

may result in equipment damage, poor freezer

performance, health hazards, or personal injury.

This appliance is to be used only by trained

personnel. It is not intended for use by children or

people with reduced physical, sensory, or mental

capabilities, or lack of experience and knowledge,

unless given supervision or instruction concerning the

use of the appliance by a person responsible for their

safety. Children should be supervised to ensure that

they do not play with the appliance.

This unit is provided with an equipotential

grounding lug that is to be properly attached to the rear

of the frame by the authorized installer. The installation

location is marked by the equipotential bonding

symbol (5021 of IEC 60417-1) on both the removable

panel and the equipment’s frame.

DO NOT use a water jet to clean or rinse the

freezer. Failure to follow these instructions may result

in serious electrical shock.

SDO NOT operate the freezer unless it is

properly grounded.

SDO NOT operate the freezer with larger fuses

than specified on the freezer data label.

SAll repairs must be performed by an

authorized Taylor service technician.

SThe main power supplies to the machine must

be disconnected prior to performing any

repairs.

SFor Cord Connected Units: Only Taylor

authorized service technicians or licensed

electricians may install a plug or replacement

cord on these units.

SStationary appliances which are not equipped

with a power cord and a plug or another device

to disconnect the appliance from the power

source must have an all-pole disconnecting

device with a contact gap of at least 3 mm

installed in the external installation.

SAppliances that are permanently connected to

fixed wiring and for which leakage currents

may exceed 10 mA, particularly when

disconnected, not used for long periods, or

during initial installation, shall have protective

devices such as a GFI to protect against the

leakage of current, installed by authorized

personnel to the local codes.

SSupply cords used with this unit shall be

oil-resistant, sheathed flexible cable, not

lighter than ordinary polychloroprene or other

equivalent synthetic elastomer-sheathed cord

(Code designation 60245 IEC 57) installed

with the proper cord anchorage to relieve

conductors from strain, including twisting, at

the terminals and protect the insulation of the

conductors from abrasion.

If the supply cord is damaged, it must be

replaced by an authorized Taylor service

technician in order to avoid a hazard.

Failure to follow these instructions may result in

electrocution. Contact your local authorized Taylor

Distributor for service.

9

Models 345, 346, 349, 355 Safety

131122

SDO NOT allow untrained personnel to

operate this machine.

SDO NOT operate the freezer unless all

service panels and access doors are

restrained with screws.

SDO NOT remove any internal operating

parts (example: freezer door, beater,

scraper blades, etc.) unless all control

switches are in the OFF position and ALL

PRESSURE IN THE FREEZING

CYLINDER HAS BEEN RELIEVED.

Failure to follow these instructions may result in

contaminated product or severe personal injury to

fingers or hands from hazardous moving parts.

This unit has many sharp edges that can

cause severe injuries.

SDO NOT put objects or fingers in the door

spout. This may contaminate the product

and cause severe personal injury from blade

contact.

SUSE EXTREME CAUTION when removing

the beater asssembly. The scraper blades

are very sharp.

This freezer must be placed on a level

surface. Failure to comply may result in personal injury

or equipment damage.

Access to the service area of the unit must be

restricted to persons having knowledge and practical

experience with the unit, in particular as far as safety

and hygiene are concerned.

Cleaning and sanitizing schedules are

governed by your state or local regulatory agencies

and must be followed accordingly. Please refer to the

cleaning section of this manual for the proper

procedure to clean this unit.

This machine is designed to maintain product

temperature under 41_F(5_C). Any product being

added to this machine must be below 41_F(5_C).

Failure to follow this instruction may result in health

hazards and poor freezer performance.

CAUTION: This unit is pressurized when in

operation. The control switch must be in the OFF

position until the unit is completely assembled. No part

should ever be removed from the machine while it is in

operation. No part should be removed until the control

switch has been turned to the OFF position and all

pressure has been relieved by opening the draw valve.

Failure to follow these instructions may result in severe

personal injury from hazardous moving parts or from

the impact of propelled parts.

IMPORTANT: DO NOT obstruct air intake and

discharge openings: These units require 6” (152 mm)

minimum air space around all sides. Failure to follow

this instruction may cause poor freezer performance

and damage to the machine.

For Indoor Use Only: This unit is designed to operate

indoors, under normal ambient temperatures of

70_-75_F(21_-24_C). The freezer has successfully

performed in high ambient temperatures of

104_(40_C) at reduced capacities.

DO NOT run the unit without product. Failure to follow

this instruction can result in damage to the unit.

NOISE LEVEL: Airborne noise emission does not

exceed 78 dB(A) when measured at a distance of 1.0

meter from the surface of the machine and at a height

of 1.6 meters from the floor.

10 Models 345, 346, 349, 355Operator Parts Identification

Section 4 Operator Parts Identification

17

5

7

11

10 6

8

12

9

16

4

13

2

15

14

13

18

Model 345

Item Description Part No.

1Panel A.-Side Left X45136

2Hood 044618

3Panel-Rear 044921-SP1

4Panel A.-Side Right X44919

5Caster-Swivel 3/4-10 St. 3” 021279

6Caster-Locking Swivel - 3” 030307

7Lock-Caster Bracket 032571

8Shield-Splash 043719

9Tray-Drip *345/6* Black w/Drain 043720-SP

10 Pan-Drip 19-1/2 Long 035034

Item Description Part No.

11 Panel-Service 044916

12 Panel-Front-Lower 043599-BLA

13 Stud-Nose Cone 5/16-18 020445

*13a Washer-Freezer Stud 036265

14 Card-Flavor Packet 035324

15 Card-FCB POP 043957

16 Panel-Front-Upper 043600-BLA

17 Plate A.-Dec-345-346-355 Black 043639-BLA

18 Decal- Dec- Taylor Domed 053761

*19 Pan-Drip (White) For Drip Guide 043612

*Not Shown

11

Models 345, 346, 349, 355 Operator Parts Identification

1

3

2

4

19

20

5

6

11

9

12

10

8

13

14

17

15

16

7

18

Model 346

Item Description Part No.

1Panel A.-Side Left X44917

2Hood 044618

3Panel-Rear 044921-SP1

4Panel A.-Side *346*AC*R*Filter X53611

5Caster-Swivel 3/4-10 St. 3” 021279

6Caster-Locking Swivel 3” 030307

7Lock-Caster Bracket 032571

8Shield-Splash 043719

9Tray-Drip 20” L x 8” D x 3-3/4 043720-SP

10 Pan-Drip 19-1/2 Long 035034

11 Panel-Service *346* Filter 053612

Item Description Part No.

12 Panel-Front-Lower 043599-BLA

13 Stud-Nose Cone 5/16-18 020445

*13a Washer-Freezer Stud 036265

14 Card-Flavor Packet 035324

15 Card-FCB POP 043957

16 Panel-Front-Upper 043600-BLA

17 Plate-Dec-345-346-355* Black 043639-BLA

18 Decal- Dec- Taylor Domed 053761

19 Filter- Air 18L x 16.5H x .70W AC 052779- 1

20 Cover- Hole- Filter- Snap In 053801

*21 Pan-Drip (White) For Drip Guide 043612

*Not Shown

12 Models 345, 346, 349, 355Operator Parts Identification

Model 349

5

4

7

11

6

8

9

10

12

14

13

2

17

18

16

13

15

Item Description Part No.

1Panel A.-Side Left X42289

2Hood 042166

3Panel-Rear *349* Drain Hole 042198

4Panel A.-Side Right X42291

5Caster-Swivel 3/4-10 St. 3” 021279

6Caster-Locking Swivel 3” 030307

7Lock-Caster Bracket 032571

8Panel-Service *349* AC 053652

9Tray-Drip (Black) w/Drain 038275-SP

10 Shield-Splash 038276

11 Panel-Front-Lower 042082-BLA

Item Description Part No.

12 Stud-Nose Cone 5/16-18 020445

*12a Washer-Freezer Stud 036265

13 Card-Flavor Packet 035324

14 Panel-Front Upper 042081-BLA

15 Plate-Dec *349* Black 035410-BLA

16 Decal- Dec- Taylor Domed 053761

17 Cover- Hole- Filter- Snap In 053801

18 Filter-Air18Lx16.5Hx.7W 052779- 1

*19 Pan A.-Drip w/Hose Left X42201

*20 Pan A.-Drip w/Hose Right X42203

*Not Shown

13

Models 345, 346, 349, 355 Operator Parts Identification

8

11

2

34

10

9

12

13

14

1

15

5

6

7

12a

Model 355

Item Description Part No.

1Panel-Front -Upper 043600-BLA

2Panel-Side-Left 044619-SP

3Hood 044618

4Panel-Rear-Stainless 044621-SS

5Panel-Side-Right 044620-SP

6Leg-4” 3/8-16 Stud 036397

7Shelf-Drip Tray 049697

8Tray-Drip 20” L x 8” D x 3-3/4 043720

9Shield-Splash 043719

Item Description Part No.

10 Pan-Drip 035034

11 Panel-Front-Lower 043599-BLA

12 Stud-Nose Cone 5/16-18 020445

*12a Washer-Freezer Stud 036265

13 Card-Flavor Packet 035324

14 Card-FCB POP 043957

15 Plate-Dec-345-346-355 Black 043639-BLA

*16 Pan-Drip (White) For Drip Guide 043612

*Not Shown

14 Models 345, 346, 349, 355Operator Parts Identification

120828

Door Assembly

ITEM DESCRIPTION PART NO.

1DOOR

1a CAP-SPOUT-DOOR-FCB-BLK 046191-BLA

1b SPRING-COMP.480X.072X3.0 039320

1c VALVE-DRAW-DOOR-PRESS. 039324

1d O-RING-9/16 OD X .103W 016369

1e SPOUT-DOOR-FCB-BLACK 046190-BLA

1f HANDLE-DRAW-FCB-BLACK 046192-BLA

1g PIN-PIVOT-SPOUT-DOOR 039321

1h SLIDE-HANDLE-DOOR-BLK 046193-BLA

1i SCREW-10-32X3/8PHL-TRUS

HD SS 053869

1j O-RING-9/32 OD X 1/16 WALL 029751

1k PLUG-PRIME-SLUSH-PRESS. 039568

1l DOOR-FREEZER-SLUSH-PRES 039573

ITEM DESCRIPTION PART NO.

1m O-RING-1.129 ODX.989ID 039219

1n NUT-SPOUT-DOOR-PRESS. 039323

2NUT-STUD 043666

3O-RING-5-1/4ODX.210W

(DOOR) 017003

4BEARING-FRONT-PRESSURE 039349

5BEATER-PLASTIC-FCB-PRESS. 041182

6BLADE-SCRAPER-FCB-16INCH 041103

7SHAFT-BEATER-SLUSH-PRES 039337

8SEAL-DRIVE SHAFT 032560

9*O-RING-7/8 OD X .139W

(BEATER SHAFT) 025307

10 BUSHING-BEATER

SHAFT/BOOT SEAL 042278

*NOTE: O-RING 025307 IS NOT USED ON CURRENT

MODELS. HOWEVER, UNITS BUILT PRIOR TO 10/09

THAT HAVE NOT BEEN UPDATED WITH METAL

REAR SHELL BEARING X67222 STILL REQUIRE

O-RING.

15

Models 345, 346, 349, 355 Operator Parts Identification

Accessories

KAY-5

Sanitizer/Cleaner

®

CAUTION

KEEP OUT OF REACH OF CHILDREN

FOR INSTITUTIONAL USE ONLY

1 OZ (28.4 g)

2

1

3

4

5

8

7

6

048260

R

ITEM DESCRIPTION PART NO.

1PAIL-MIX 10 QT 013163

2BRUSH-MIX PUMP BODY-3”X7” 023316

3BRUSH-DOUBLE ENDED 013072

4BRUSH-REAR BRG 1”DX2“L 013071

5BRUSH-DRAW VALVE 1-1/2”OD 014753

ITEM DESCRIPTION PART NO.

6KIT A.-TUNE UP X39699

7LUBRICANT-TAYLOR HI PERF 048232

8SANITIZER KAY-5 25 PACKETS 041082

*SANITIZER STERA-SHEEN 010425

*NOT SHOWN

16 Models 345, 346, 349, 355Important: To the Operator

Section 5 Important: To the Operator

Figure 8

Item Description

1Control Switch

2Liquid Crystal Display

3Keypad- Left

4Keypad- Right

5Product Light- Left Side

6Product Light- Right Side

Symbol Definitions

To better communicate in the International arena, the

words on many of our operator switches and keys have

symbols to indicate their functions. The Model 349 is

designed with these International symbols.

The following chart identifies the symbol definitions

used on the Model 349.

=ON

=OFF

=AUTO

=PRIME

= BEATER MOTOR

= ALARM SILENCE

= MENU/SELECT

Control Switch

The control switch is located on the top of the control

channel. When placed in the ON position, allows

Slushtechtoperation.

17

Models 345, 346, 349, 355 Important: To the Operator

Liquid Crystal Display

The Liquid Crystal Display (LCD) is located on the front

control panel. The LCD is used to show the current

operating mode of the freezing cylinders. The LCD

also indicates whether there is enough syrup, CO2,

and water being supplied to the freezer. If an error in

the machine operation occurs, a warning tone will

sound and the word “FAULT” will flash on the third line

of the display.

Operational Mode Display

When the unit is plugged into the wall receptacle and

the power switch is placed in the ON position, this

screen appears.

SAFETY TIMEOUT

ANY KEY ABORTS

This display will remain on the LCD for 60 seconds

unless a key is pressed. If any key is pressed (or 60

seconds passes), then the next screen appears.

OFF MODE OFF

OK SYRUP OK

CO2=OK WATER=OK

Note: Syrup, CO2and water are satisfied.

Pressing both AUTO keys will display this screen.

AUTO MODE AUTO

OK SYRUP OK

CO2=OK WATER=OK

Line 1 indicates the operating mode for each cylinder.

Line 2 indicates the status of the syrup systems in each

freezing cylinder.

Line 3 indicates if there is a fault in the system (left

side).

The same rules apply to the fourth line which indicates

the status of the CO2and the H2O.

AUTO MODE OFF

OK SYRUP OK

- - FAULT- -

CO2=OK WATER=OK

Operator Menu Display

The OPERATOR MENU is used to enter into the

operating screens. To access the OPERATOR MENU,

simply press the word “MENU”. The cursor will flash

under the letter “A”, indicating that this is screen A. To

select a different screen, use the arrow keys to move

the cursor to the desired screen selection and press

the SEL key.

OPERATOR MENU

ABCDEFGH

EXIT MENU

<- - - -> SEL

Operator Menu Timeout

If the display is left in the operator menu or any of the

operator menu selections, except for Current

Conditions, the display will return to the system mode

screen 60 seconds after the last keypress. The

Current Conditions screen will be displayed until

manually changed.

18 Models 345, 346, 349, 355Important: To the Operator

060801

Finding Current Fault Conditions

Screen B is FAULT DESCRIPTION. The fault

description will indicate if there is a fault in one of the

freezing cylinders. When the actual fault is corrected,

the warning tone will stop. Only items 9 and 10 require

pressing the OFF/<--- key to clear the fault message

and the warning tone.

Fault Messages

Beater Overload Beater is out on overload.

Chk Refrig Sys Psi Compressor is out on high

head pressure (or low

suction pressure = option

that applies to some units)

Thermistor Short Shorted thermistor probe.

Thermistor Open Open thermistor probe.

H2O Pressure Low Water pressure is low.

CO2 Pressure Low CO2pressure is low.

Syrup Pressure Low Syrup is no longer present.

BRLTemp2High Freezing cylinder

temperature is above 120_F

(49_C).

BRL Not Cooling Freezing cylinder is not

cooling after 5 minutes.

No Fault Found No fault conditions are

apparent.

The following are explanations of the possible faults

and the display screens.

Lines 2 and 3 indicate the faults found in the left and

right freezing cylinders respectively. The screen below

indicates that no faults exist on either side. To see if

there is more than one fault, press the +++ key.

Note: On a Model 349, faults for freezing cylinders 1

and 2 are shown on the first screen. Press the SEL key

to read fault messages for freezing cylinders 3 and 4.

1. NO FAULT FOUND - No fault conditions are

apparent.

FAULT DESCRIPTION

L: NO FAULT FOUND

R: NO FAULT FOUND

CLR +++ SEL

2. BEATER OVERLOAD - Beater motor is out on

overload. When this fault occurs, the machine

automatically turns off. The fault clears when

the condition is corrected.

FAULT DESCRIPTION

L: BEATER OVERLOAD

R: BEATER OVERLOAD

CLR +++ SEL

3. CHK REFRIG SYS PSI - Compressor is out on

high head pressure (or low suction pressure =

option that applies to some units). When this

fault occurs, the machine automatically turns

off. The fault clears when the condition is

corrected.

FAULT DESCRIPTION

L: CHK REFRIG SYS PSI

R: CHK REFRIG SYS PSI

CLR +++ SEL

4. THERMISTOR SHORT - One or both of the

barrel (freezing cylinder) thermistor probes are

faulty.

FAULT DESCRIPTION

L: THERMISTOR SHORT

R: NO FAULT FOUND

CLR +++ SEL

5. THERMISTOR OPEN - One or both of the

barrel (freezing cylinder) thermistor probes are

faulty.

FAULT DESCRIPTION

L: THERMISTOR OPEN

R: NO FAULT FOUND

CLR +++ SEL

19

Models 345, 346, 349, 355 Important: To the Operator

6. SYRUP PRESS LOW - When the syrup out

indicator displays a lack of syrup, a 15 minute

internal timer will start. At this time, no

refrigeration or product flow from the flow

control will be allowed. Only the beater and

CO2operate. If the syrup is not replenished at

the end of the 15 minutes, the freezing cylinder

will shut down and this fault message will

appear. Replenish the syrup, and the fault

message and warning tone will clear. If using a

tank system, priming may be required.

(Example shown is for the right side.)

FAULT DESCRIPTION

L: NO FAULT FOUND

R: SYRUP PRESS LOW

CLR +++ SEL

7. CO2PRESSURE LOW - When the CO2out

indicator displays a lack of CO2, a 60 second

internal timer will start. If the CO2is not

replenished at the end of the 60 seconds, both

freezing cylinders will shut down and this fault

message will appear. Replenish the CO2and

the fault message and warning tone will clear.

FAULT DESCRIPTION

L: CO2 PRESSURE LOW

R: CO2 PRESSURE LOW

CLR +++ SEL

8. H2O PRESSURE LOW - When the water out

indicator displays a lack of water, a 60 second

internal timer will start. If the water is not

replenished at the end of the 60 seconds, all

freezing cylinders will shut down and this fault

message will appear. Replenish the water and

the fault message and warning tone will clear.

FAULT DESCRIPTION

L: H2O PRESSURE LOW

R: H2O PRESSURE LOW

CLR +++ SEL

9. BRL NOT COOLING - A freezing cylinder

check has been established for the AUTO

mode of operation. If a freezing cylinder enters

the AUTO mode, the control will check product

temperature. After five minutes, it will again

check product temperature. If product

temperature does not drop in that five minute

time span, the freezing cylinder will shut down

and this message will appear on the fault

screen. For this check to be valid, the product

temperature must be above 40_F(4.4_C), and

the fill switch cannot be activated. If a fill

condition exists during this time, the five minute

check will be re-initiated.

FAULT DESCRIPTION

L: BARREL NOT COOLING

R: NO FAULT FOUND

CLR +++ SEL

10. BRL TEMP 2 HIGH - A maximum allowable

product temperature has been established to

prevent product from excessive heating. If the

product exceeds 120_F(49_C) temperature for

any reason (in any mode of operation), the

entire unit shuts down.

FAULT DESCRIPTION

L: BARREL TEMP 2 HIGH

R: NO FAULT FOUND

CLR +++ SEL

Faults, when corrected, are cleared from the fault

description screen, with the following exceptions: BRL

NOT COOLING and BRL TEMP 2 HIGH. These faults

require the operator to press the OFF key (when in the

FAULT DESCRIPTION screen) in order for the fault to

discontinue.

To see if there is more than one fault in either freezing

cylinder, press the plus key. To return to the

OPERATOR MENU, press the SEL key once. To

return to the Main Screen, use the right arrow key to

cycle to MENU ITEM A, then press the SEL key.

20 Models 345, 346, 349, 355Important: To the Operator

041011

Screen C is SET CLOCK. Move the cursor under the

number you wish to change. Press the +++ key to

increase the number; press the - - - key to decrease

the number. When the desired time and date appears,

press the SEL key once to return to the OPERATOR

MENU.

Note: The clock is programmed with military time.

SET CLOCK

14:30 6/25/01

<-- --> +++ - - - SEL

This screen will appear if an invalid date is entered.

(example: If the date entered exceeds the days of that

month.)

SET CLOCK

14:30 02/31/01

INVALID DATE

SEL

This screen allows the Daylight Saving Time options.

DAYLIGHT SAVING TIME

ENABLE DISABLE

<--- ---> SEL

If the Daylight Saving Time option is enabled, then the

time will be advanced by one hour at 2:00 a.m. on the

first Sunday in April, and will be retarded by one hour

at 2:00 a.m. on the last Sunday in October.

Screen D is MANUAL DEFROST. This screen allows

the operator to manually defrost theleftsideofthe

unit.

Place the cursor under YES, press the SEL key, and

the command will be executed.

MANUAL DEFROST

LEFT SIDE YES NO

<--- ---> SEL

Repeat the procedure for the right side of the unit.

MANUAL DEFROST

RIGHT SIDE YES NO

<--- ---> SEL

Note: The models 345 and 355 allow only one

freezing cylinder to be defrosted at a time. This applies

to freezing cylinder pairs on the model 349. Attempting

to place a freezing cylinder into defrost while the other

freezing cylinder is defrosting will result in the following

screen. (Model 346 does not have this restriction.)

ALREADY IN DEFROST

Press the SEL key to return the unit to the OPERATOR

MENU.

Screen E is SYSTEM INFORMATION. It consists of

6 display features.

Press the SEL key to advance to the next feature.

The first feature indicates the software version.

SYSTEM INFORMATION

355 CONTROL UVC2

VERSION 2.03

SEL

21

Models 345, 346, 349, 355 Important: To the Operator

The second feature indicates the bill of material

number and the serial number.

It also indicates if the unit is equipped with a water

pressure switch.

B.O.M. 035527C000

S/N K0000000

WITH H20 PRESS SW

SEL

The third feature indicates the version number of the

language and text.

SYSTEM INFORMATION

LANGUAGE

VERSION 1.05 ENGLISH 386

SEL

The fourth feature will display the Power Saver Mode,

as OFF, REST, or STANDBY.

If the Power Saver Mode is OFF, the following screen

will be displayed.

POWER SAVER MODE

OFF

SEL

If a Power Saver Mode is programmed, one of the

following screens will appear. (The model 349 will

display defrost information for freezing cylinders 1, 2,

3, and 4 instead of LEFT and RIGHT.)

There are seven possible Power Saver Mode time

frames (cycles). The second display line shows the

cycle (1 of 7) as well as the time and day at which the

Power Saver Mode will begin for that cycle. The third

line shows the time and day that the Power Saver

Mode will end for that cycle. Press the +++ or - - - keys

to view other cycles.

POWER SAVER REST

CYCLE 1 SUN 01:00

SUN 08:30

+++ - - - SEL

POWER SAVER STANDBY

CYCLE 1 SUN 01:00

SUN 08:30

+++ - - - SEL

The fifth feature will indicate the left side defrost

time(s) and which day(s) the defrost will occur.

Each freezing cylinder has eight possible defrost times

(cycles) for each day of the week. If all seven days

have the same time for a given cycle, then thefollowing

screen will appear. This example shows that ALL

seven days have CYCLE 1 programmed for 9:00.

Pressthe+++or---keystoviewothercycles.

DEFROST TIME LEFT

CYCLE 1 ALL 09:00

+++ - - - SEL

If one or more days of the week have a given cycle

programmed at different times, then the following

display will appear. This example shows that Sunday’s

CYCLE 1 is programmed for 9:00. The fact that SUN

is displayed (instead of ALL) indicates that some other

day(s) CYCLE 1 is programmed for a different time (or

not programmed at all). Using the cursor keys, place

the cursor under the cycle number. Press the +++ or

---keystoviewotherdefrosttimes(cycles) for the day

shown. Place the cursor under the day (SUN) and

press the +++ or - - - keys to access the other days of

the week.

DEFROST TIME LEFT

CYCLE 1 SUN 09:00

<--- ---> +++ --- SEL

The sixth feature will indicate the right side defrost

time(s) and which day(s) the defrost will occur.

Note: The functionality is the same as described

previously for the left side defrost.

DEFROST TIME RIGHT

CYCLE 1 ALL 10:00

+++ - - - SEL

22 Models 345, 346, 349, 355Important: To the Operator

060522

DEFROST TIME RIGHT

CYCLE 1 SUN 10:00

<--- ---> +++ --- SEL

Press the SEL key to return to the OPERATOR MENU.

Screen F is CURRENT CONDITIONS. This screen

displays the current viscosity and product temperature

for each freezing cylinder. An asterisk will indicate

which side is refrigerating. Press the SEL key to return

to the OPERATOR MENU.

Note: Viscosity is checked only when product

temperature is below 40_F/4.4_C.

The following screen is exemplary of models 345, 346,

and 355. The model 349 displays all four freezing

cylinders.

CURRENT CONDITIONS

L* 999HD 27.5F

R 1200HD 26.5F

SEL

Screen G is FAULT HISTORY. This option provides

a record of the last 20 faults. The display also indicates

the date and time each fault occurs.

FAULT HISTORY 1

06/25/01 08:34

NO FAULT FOUND

+++ - - - SEL

Press the arrow keys to increase or decrease the

fault page.

Page numbers are located in the upper right hand

corner of the display. The most recently recorded fault

will appear on page 1.

FAULT HISTORY 2

06/25/01

R SYRUP PRESS LOW 08:33

+++ - - - SEL

The fault description is listed on the third line of the

fault page.

FAULT HISTORY 3

06/25/01 08:32

B H2O PRESS LOW

+++ - - - SEL

Press the MENU/SEL key to return to the OPERATOR

MENU.

Screen H is SERVICE MENU. This screen allows the

authorized service technician to access service

information. Return to the OPERATOR MENU by

using the arrow keys to move the cursor under the

letter “A”, and press the MENU/SEL key.

OPERATOR MENU

ABCDEFGH

SERVICE MENU

<--- ---> SEL

Syrup Out Indicator

AUTO MODE AUTO

OUT SYRUP OK

CO2- OK WATER- OK

If the word “OUT” appears in one of the columns next

to the word “SYRUP”, it indicates a lack of syrup or

syrup pressure being supplied for the indicated

freezing cylinder. If the unit is in the AUTO or PRIME

modes, the product light will flash and a warning tone

will sound for that freezing cylinder. At this time,

replace the appropriate syrup. As a safety feature, the

refrigeration system automatically stops to prevent a

freeze-up in the freezing cylinder.

If a syrup out condition occurs on one side, that side

will enter the HOLD mode at which time refrigeration

remains off, the beater continues to run, and the

CO2solenoid is closed for that side to prevent the

dispensing of product. The opposite side will not be

affected.

23

Models 345, 346, 349, 355 Important: To the Operator

CO2Out Indicator

AUTO MODE AUTO

OK SYRUP OK

CO2- OUT WATER- OK

On the LCD, if the word “OUT” appears next to the

word “CO2” it indicates a lack of CO2being supplied to

the freezer. The product light will also flash and a

warning tone will sound. This will continue until the

CO2is replaced. If the CO2is not replaced within one

minute, the machine will shut down and a fault

message will appear.

Water Out Indicator

AUTO MODE AUTO

OK SYRUP OK

CO2- OK WATER- OUT

On the LCD, if the word “OUT” appears next to the

word “WATER”, it indicates a lack of water being

supplied to the freezer. In addition, the product light will

flash and a warning tone will sound. This will continue

until the proper amount of water is supplied to the

freezer. If the water is not supplied within one minute,

the machine will shut down and a fault message will

appear.

Audio Alarm Silencer

The audio alarm will be disabled if the ALARM

SILENCE key is pressed. If a new fault or fault

condition occurs or the system mode changes, the

audio alarm will be re-enabled automatically. If the

audio alarm is silenced for greater than 30 minutes

without correcting the fault, it will be re-enabled

automatically.

Product Light

When the light is flashing, it indicates that the product

is not at serving viscosity. This will occur during the

initial freeze down, a defrost cycle and a FAULT

condition and during power saver modes.

Sampling Valve

The sampling valve is located behind the front drip tray.

The sampling valve is used to obtain a brix reading.

Daily Procedures

The following procedure should be performed daily.

Remove the splash shield, front drip tray and center

drip pan. Take these parts to the sink and brush-clean

them. Re-install the parts onto the freezer.

24 Models 345, 346, 349, 355Operating Procedures

Section 6 Operating Procedures

The Models 345, 346 and 355 contain two 7 quart (6.6

liter) freezing cylinders. The Model 349 contains four

7 quart (6.6 liter) freezing cylinders.

CAUTION: This unit is pressurized when

in operation. The control switch, located on the top

side of the control box must be in the OFF position until

the unit is completely assembled. No part should ever

be removed from the machine while it is in operation.

No parts should be removed until the control switch

has been turned to the OFF position and all pressure

has been relieved at the draw handle.

The syrup flow controls combine the two ingredients of

soda water and syrup, and send this combination to

the mix hoppers. As product is drawn, new product

from the hopper will flow through a mix feed tube down

into the freezing cylinder. The mix hopper is supplied

with 20 pounds of CO2gas for dispensing the finished

product.

We begin our instructions at the point where the parts

are disassembled and laid out to air dry.

The following procedures will show you how to

assemble the parts into the freezer, sanitize them, and

prime the freezer with fresh product.

Duplicate the following procedures, where they apply,

for the remaining freezing cylinder(s).

If you are disassembling the machine for the first time

or need information to get to this starting point in our

instructions, turn to page 36 , “Disassembly” and start

there.

Assembly

MAKE SURE THE CONTROL SWITCH ISIN

THE OFF POSITION. Failure to do so may result in

personal injury or component damage.

Note: When lubricating parts, use an approved food

grade lubricant (example: Taylor Lube HP).

Step 1

Lubricate the o-ring groove. Slide the o-ring into the

groove on the drive shaft. Lubricate the drive shaft seal

groove, the o-ring, and the shaft portion that comes in

contact with the bearing on the beater drive shaft. DO

NOT lubricate the hex end of the drive shaft.

Figure 9

Lubricate the inside diameter of the drive shaft seal.

Install the drive shaft seal bushing in the drive shaft

seal.

Figure 10

25

Models 345, 346, 349, 355 Operating Procedures

Note: The drive shaft bushing must be positioned in

the center of the drive shaft seal.

Slide the seal and bushing over the shaft and groove

until it snaps into place. Fill the inside portion of the

seal with 1/4” more lubricant and evenly lubricate the

end of the seal that fits onto the rear shell bearing.

Figure 11

Insert the beater drive shaft into the freezing cylinder,

hex end first, and into the rear shell bearing until the

seal fits securely over the rear shell bearing. Be certain

the drive shaft fits into the drive coupling without

binding. Remove any excess lubricant from the seal.

Figure 12

Step 2

Install the beater assembly. First check the scraper

blades for any nicks or signs of wear. If any nicks are

present or if the blade is worn, replace both blades. If

the blades are in good condition, place the scraper

blades over the holding pins on the beater.

Note: Each hole on the scraper blade must fit

securely over each pin.

Figure 13

Align the flats on the end of the beater assembly with

the drive shaft. Make sure the beater assembly

locating pin is in position in the locating hole of the drive

shaft. Turn the beater slightly to be certain that the

beater is properly seated. When in position, the beater

will be approximately 3/8” inside the front of the

freezing cylinder.

Important: Failure to properly seat the beater may

cause damage to the beater and the door.

Figure 14

26 Models 345, 346, 349, 355Operating Procedures

Note: The scraper blades on the beater assembly

should be in the 6 and 12 o’clock positions. This will

enable freezer door installation.

Figure 15

Step 3

Install the draw valve. Slide the two o-rings into the

grooves on the draw valve. Lubricate the o-rings and

the valve as illustrated below.

Figure 16

Insert the draw valve into the freezer door spout from

the front of the unit. The valve is properly installed

when the hole in the draw valve is visible in the slot of

the freezer door spout.

Figure 17

Snap the draw valve handle onto the door spout. Align

the hole in the draw valve with the slot in the draw

handle.

Figure 18

Slide the pivot pin through the draw handle and into the

draw valve.

Figure 19

27

Models 345, 346, 349, 355 Operating Procedures

Place the draw handle slide over the opening in the

draw handle and the pivot pin. Secure the assembly

with screws.

Figure 20

Insert the spring into the front of the door spout.

Figure 21

Place the threaded cap on the end of the draw valve

cavity. Turn the cap clockwise until it is secure.

Figure 22

Step 4

Install the prime plug. Place the two o-rings on the

prime plug and lightly lubricate.

Figure 23

Step 5

Place the large o-ring into the door groove and lightly

lubricate.

Figure 24

Note: Every three months, discard the o-rings and

install new o-rings.

28 Models 345, 346, 349, 355Operating Procedures

Step 6

Install the front bearing. Do not lubricate the front

bearing.

Figure 25

Step 7

Install the freezer door. Position the door on the four

studs on the front of the freezing cylinder. Firmly push

the door into place. Install the four handscrews on the

studs and finger-tighten them equally in a criss-cross

pattern to insure that the door is snug. Do not

over-tighten the handscrews.

Figure 26

Step 8

Place the o-ring into the groove of the hopper cover.

Figure 27

Install the hopper cover. Lock it into place.

Figure 28

Attach the vinyl tube to the pressure relief on the

hopper cover. Position the open end of the vinyl tube

into the rear drip pan.

Figure 29

Repeat Steps 1 through 8 for the remaining freezing

cylinder(s).

29

Models 345, 346, 349, 355 Operating Procedures

Step 9

Install the center drip pan through the front of the

machine.

Figure 30

Sanitizing

Note: If a unit is sanitized, and will not be used for an

extended period of time, clean water should be used

to flush all sanitizer from the lines prior to storage of the

unit. Upon return to service, the unit must be sanitized

prior to use.

Step 1

Open the lighted display door. Remove the hood and

the side panels to gain access to the hoppers. Place

the control switch in the ON position.

Figure 31

Step 2

Prepare two gallons (7.6 liters) of an approved 100

PPM sanitizing solution (example: Kay-5R). USE

WARM WATER AND FOLLOW THE MANUFACTUR-

ER’S SPECIFICATIONS. IMPORTANT: Make sure

the sanitizer is completely dissolved.

If your freezer uses Bag in Box syrup, follow steps 3

through 5. If your freezer uses syrup tanks, follow the

instructions on page 5.

Step 3

BaginBoxUnitsOnly:Using an empty bag of syrup,

cut the syrup line connection from the end of the bag.

Figure 32

Step 4

Connect the syrup line to the syrup connection that

was cut from the syrup bag.

Figure 33

30 Models 345, 346, 349, 355Operating Procedures

Step 5

With the bag connector attached to the syrup line,

place the syrup line into the pail of sanitizing solution.

Figure 34

Replace Steps 3 - 5 for Syrup Tank Units: Pour the

solution into a clean, empty syrup tank. Place the

syrup tank cover in position. Remove the CO2line and

syrup line number one from the syrup tank for freezing

cylinder number one. Connect these lines to the spare

syrup tank filled with sanitizing solution.

Figure 35

Step 6

Press the PRIME key. This will cause the sanitizing

solution to flow through the lines and into the mix

hopper.

Figure 36

Step 7

Place a mix pail beneath the sampling valve which is

located behind the front drip tray. Slowly open the

sampling valve and allow sanitizer to flow through this

line and into the pail. After approximately 1/2 gallon of

sanitizer has been dispensed, close the valve.

Step 8

Raise the prime plug only enough to allow a slight

hissing sound. Place an empty pail under the door

spout. When sanitizing solution begins to exit the relief

port opening in the freezer door, lower the prime plug.

Press the OFF key.

Figure 37

Step 9

Prepare two gallons (7.6 liters) of an approved 100

PPM sanitizing solution (example: Kay-5R). USE

WARM WATER AND FOLLOW THE MANUFACTUR-

ER’S SPECIFICATIONS.

31

Models 345, 346, 349, 355 Operating Procedures

Step 10

With the pail beneath the door spout, open the draw

valve and relieve all pressure from the freezing

cylinder. Remove the hopper cover. Slowly pour the

two gallons (7.6 liters) of sanitizing solution into the mix

hopper until the hopper becomes 1/4 full of sanitizing

solution.

Figure 38

Step 11

With the brushes provided, brush-clean the mix

hopper, mix inlet hole, mix level float switch, product

fitting, CO2fitting and mix feed tube. Use caution when

cleaning the float switch so as not to damage it.

Figure 39

Figure 40

Figure 41

Figure 42

32 Models 345, 346, 349, 355Operating Procedures

Figure 43

Step 12

Install the mix feed tube into the mix inlet hole in the

bottom of the mix hopper.

Figure 44

Step 13

Sanitize and install the hopper cover. Lock the cover

into place. Attach the vinyl tube to the pressure relief

valve on the hopper cover. Position the open end of the

vinyl tube into the rear drip pan.

Figure 45

Step 14

Press the BEATER key. Agitate the solution in the

freezing cylinder for five minutes.

Figure 46

Step 15

With a pail beneath the door spout, open the draw

valve and drain all the solution from the mix hopper and

the freezing cylinder. Press the OFF key and close the

draw valve.

Figure 47

Step 16

Disconnect the syrup connector in the sanitizing

solution.

Repeat Steps 2 through 14 for the remaining freezing

cylinder(s).

Step 17

Remove the right side panel and install the rear white

drip pan.

33

Models 345, 346, 349, 355 Operating Procedures

Priming/Brixing

Step 1

Connect the syrup line to the syrup tank (or the Bag in

Box).

Step 2

Press the BEATER key to pressurize the freezing

cylinder.

Figure 48

After three minutes, press the PRIME key. This will

cause the product to flow to the mix hopper.

Figure 49

Step 3

Raise the prime plug enough to allow a slight hissing

sound.

Figure 50

Note: The pressure in the freezing cylinder should be

relieved very slowly.

Step 4

Slowly open the syrup sampling valve and let it run into

a bucket until all the sanitizer is removed and full

strength product is flowing. Do not open the valve so

much that the syrup line to the hopper is drained.

Figure 51

Brix is the ratio of syrup to water which will directly

affect the quality and taste of the product. Brixing

should be done before priming the freezer and when

a change in syrup flavor has been made.

34 Models 345, 346, 349, 355Operating Procedures

Allow the product to flow over the refractometer. The

brix reading should register 13 to 14. A reading higher

than this would cause a darker, richer product. The

refrigeration system would have to run longer to freeze

this excess syrup. A reading lower than this could

cause a freeze-up in the freezing cylinder because of

the excess water.

Figure 52

To adjust the brix, turn the adjustment screw located

in the service panel. Clockwise adjustments increase

the amount of syrup to water, and counterclockwise

adjustments decrease the amount of syrup to water.

Adjust the screw in small increments and check the

brix again.

Figure 53

Repeat this step until a correct brix reading is

registered.

Step 5

Once the proper brix has been achieved, close the

sampling valve. Install the front drip tray and the splash

shield on the front of the freezer.

Figure 54

Step 6

With a pail beneath the door spout, press the BEATER

key. Open the draw valve and drain the freezing

cylinder. Close the draw valve. After three minutes,

press the PRIME key. This will cause the product to

flow to the mix hopper.

Step 7

Hold a large cup under the pressure relief port exit of

the door, until the liquid level (not foam) reaches the

pressure relief port. Lower the prime plug. Press the

OFF key.

Note: A large amount of foam indicates that the prime

plug was raised too high.

Repeat Steps 1 through 7 for the remaining freezing

cylinder(s).

Step 8

To place the freezing cylinder in the AUTO mode,

press the AUTO key. When the unit cycles off, the

product will be at serving viscosity.

Figure 55

Repeat this step for the remaining freezing

cylinder(s).

35

Models 345, 346, 349, 355 Operating Procedures

Step 9

Replace the side panels and close the lighted display.

Install the hood in position on top of the freezer.

90 Day Closing Procedure

We recommend that the machine be completely

disassembled and cleaned at least every ninety days

using the following procedures.

ALWAYS FOLLOW LOCAL HEALTH CODES

To disassemble a freezer, the following items will be

needed:

STwo cleaning pails

SNecessary brushes (provided with freezer)

SCleaner

SSingle service towels

Draining Product From the

Freezing Cylinder

Step 1

Press the BEATER key. This will allow the beater to

operate and CO2pressure will be maintained to push

the product from the freezing cylinder. Open the draw

valve and drain the product from the machine until the

CO2begins to jet.

Figure 56

Step 2

When all the product has been drained from the mix

hopper and the freezing cylinder, close the draw valve

and press the OFF key. Discard this product.

Figure 57

Repeat Steps 1 and 2 for the remaining freezing

cylinder(s).

Cleaning

Step 1

Open the lighted display door from the front of the

machine. Remove the hood and side panels to gain

access to the hoppers.

Step 2

Prepare two gallons (7.6 liters) of an approved clean-

ing solution (example: Kay-5R). USE WARM WATER

AND FOLLOW THE MANUFACTURER’S SPECIFI-

CATIONS.

Important: Make sure the cleaner is completely

dissolved.

Step 3

Pour the solution into a clean, empty bucket. Place the

syrup line with old syrup connection into the bucket of

sanitizer.

Step 4

Press the PRIME key. This will cause the cleaning

solution to flow through the lines and into the mix

hopper.

Step 5

Remove the front drip tray. Place a mix pail beneath

the sampling valve located behind the front drip tray.

Slowly open the sampling valve and allow cleaner to

flow through this line and out into the pail. After

approximately 1/2 gallon of cleaner has been

dispensed, close the valve.

36 Models 345, 346, 349, 355Operating Procedures

Step 6

Raise the prime plug. Place an empty pail under the

door spout. When cleaning solution begins to exit the

relief port opening in the freezer door, lower the prime

plug. Press the OFF key. Open the draw valve and

relieve all pressure from the freezing cylinder. Remove

the hopper cover. Remove the mix feed tube and take

it to the sink for further cleaning. Close the prime plug.

Step 7

Prepare two gallons (7.6 liters) of an approved

cleaning solution (example: Kay-5R). USE WARM

WATER AND FOLLOW THE MANUFACTURER’S

SPECIFICATIONS.

Step 8

Slowly pour two gallons (7.6 liters) of cleaning solution

into the mix hopper until the hopper becomes 1/4 full

of cleaning solution.

Step 9

With the brushes provided, brush-clean the mix

hopper, mix inlet hole, mix level float switch, product

fitting, and CO2fitting. Use caution when cleaning the

float switch. Failure to do so will cause damage to the

component.

Step 10

Clean and install the hopper cover. Lock the cover into

place. Attach the vinyl tube to the pressure relief valve

on the hopper cover. Position the open end of the vinyl

tube into the rear drip pan.

Step 11

Press the BEATER key to agitate the solution in the

freezing cylinder.

Step 12

With a pail beneath the door spout, open the draw

valve and drain all the solution from the mix hopper and

the freezing cylinder. Press the OFF key and close the

draw valve.

Step 13

Disconnect the syrup connector.

Repeat Steps 2 through 13 for the remaining freezing

cylinder(s).

Disassembly

Step 1

Be sure the control switch is in the OFF position. Open

the draw valves to make sure all pressure has been

relieved.

Step 2

Raise the prime plug. Leave the bleed port open when

removing the freezer door to insure that all pressure is

relieved from the freezing cylinder.

Step 3

Remove the following parts from the freezer and take

them to the sink for brush-cleaning: handscrews,

freezer doors, beater assemblies and scraper blades,

drive shafts, hopper covers, front drip tray, splash

shield.

Brush Cleaning

Step 1

Prepare a sink with an approved cleaning solution.

USE WARM WATER AND FOLLOW THE

MANUFACTURER’S SPECIFICATIONS (example:

Kay-5R). IMPORTANT: Follow the label directions.

Too STRONG of a solution can cause parts damage,

while too MILD of a solution will not provide adequate

cleaning. Make sure all brushes provided with the

freezer are available for brush cleaning.

Step 2

Return to the freezer with a small amount of cleaning

solution. With a single service towel, wipe clean the

bearing surface. Brush-clean the rear shell bearings at

the back of the freezing cylinders with the black bristle

brush.

Figure 58

Step 3

Remove the rear drip pan. (Does not apply to the

Model 349.)

37

Models 345, 346, 349, 355 Operating Procedures

Step 4

Remove the right side panel and take the rear, white

drip pan to the sink for further cleaning.

Step 5

Remove the following parts: seals and o-rings from the

drive shafts, drive shaft seal bushings from drive shaft

seals, caps and springs from freezer doors, screws

and draw handle slides from freezer doors, pivot pins

from draw valves, draw valve handles from freezer

doors, draw valves from freezer doors, o-rings from

draw valves, prime plugs from freezer doors, o-rings

from prime plugs, o-rings and front bearings from

freezer doors, o-rings from mix hopper covers.

Discard all o-rings and replace them with new ones.

Note: To remove o-rings, use a single service towel to

grasp the o-ring. Apply pressure in an upward direction

until the o-ring pops out of its groove. With the other

hand, push the top of the o-ring forward. It will roll out

of the groove and can be easily removed. If there is

more than one o-ring to be removed, always remove

the rear o-ring first. This will allow the o-ring to slide

over the forward rings without falling into the open

grooves.

Step 6

Using a single service towel, wipe the lubricant off the

parts. Brush-clean all disassembled parts in the

cleaning solution. Make sure all lubricant and syrup is

removed. Place all the cleaned parts on a clean, dry

surface to air-dry.

Step 7

Wipe clean all the exterior surfaces of the freezer.

38 Models 345, 346, 349, 355Important: Operator Checklist

Section 7 Important: Operator Checklist

During Cleaning and Sanitizing

ALWAYS FOLLOW LOCAL HEALTH CODES

Cleaning and sanitizing schedules are governed by

your State or local regulatory agencies and must be

followed accordingly. The following check points

should be stressed during the cleaning and sanitizing

operations.

WE RECOMMEND CLEANING AND SANITIZING

EVERY 90 DAYS.

Troubleshooting Bacterial Count

j1. Thoroughly clean and sanitize the machine

regularly, including complete disassembly and

brush cleaning.

j2. Use all brushes supplied for thorough cleaning.

The brushes are specially designed to reach all

product passageways.

j3. Use the white bristle brush to clean the mix inlet

hole which extends from the mix hopper down

to the rear of the freezing cylinder.

j4. Use the black bristle brush to thoroughly clean

the rear shell bearing located at the rear of the

freezing cylinder. Be sure there is a generous

amount of cleaning solution on the brush.

j5. Using a screwdriver and a cloth towel, keep the

rear shell bearing and the female hex drive

socket clean and free of lubricant and product

deposits.

j6. Properly prepare the cleaning and sanitizing

solutions. Read and follow the label directions

carefully. Too strong of a solution may damage

the parts and too weak of a solution will not do

an adequate job of cleaning or sanitizing.

j7. Clean and sanitize the syrup lines regularly to

prevent syrup residue build-up that would

restrict the proper flow of syrup.

j8. On a regular basis, take a brix reading to assure

a consistent quality product.

Regular Maintenance Checks

j1. Replace scraper blades that are nicked,

damaged or worn down.

j2. Before installing the beater, be certain that the

scraper blades are properly attached over the

pins.

j3. Check the rear shell bearing for signs of wear

(excessive product leakage from the rear drip

pans to the front drip tray).

j4. Dispose of o-rings or seals if they are worn, torn,

or fit too loosely, and replace with new ones.

j5. Follow all lubricating procedures as outlined in

“Assembly”.

j6. Check the condenser(s) for accumulation of dirt

and lint. Dirty condensers will reduce the

efficiency and capacity of the machine.

Condensers should be cleaned monthly by

removing the poly- flo filter and cleaning it.

Remove the service panel and side panels to

expose the condenser(s). Never use

screwdrivers or other metal probes to clean

between the fins.

39

Models 345, 346, 349, 355 Important: Operator Checklist

Winter Storage

If the place of business is to be closed during the winter

months, it is important to protect the freezer by

following certain precautions, particularly if the

building is subject to freezing conditions.

Disconnect the freezer from the main power source to

prevent possible electrical damage.

Your local Taylor Distributor can perform this service

for you.

Wrap detachable parts of the freezer such as the

beater, the scraper blades, the drive shaft, and the

freezer door. Place these parts in a protected, dry

place. Rubber trim parts and gaskets can be protected

by wrapping them with moisture-proof paper. All parts

should be thoroughly cleaned of dried mix or

lubrication which attract mice and other vermin.

Note: It is recommended that an authorized service

technician perform winter storage draining, to insure

all water has been removed. This will guard against

freezing and rupturing of the components.

40 Models 345, 346, 349, 355Troubleshooting Guide

Section 8 Troubleshooting Guide

PROBLEM PROBABLE CAUSE REMEDY PAGE

REF.

1. Product is too stiff. a. Too much water to syrup

ratio. Improper brix

adjustment.

a. Adjust the brix

accordingly.

33

b. Consistency control needs

adjustment.

b. Contact a service

technician.

---

c. Torque coupling bound in

WARM position.

c. Contact a service

technician.

---

2. Product is too soft. a. Freezer in a defrost cycle. a. Wait for defrost cycle to

end.

---

b. Consistency control needs

adjustment.

b. Contact a service

technician.

---

c. Torque coupling bound in

COLD position.

c. Contact a service

technician.

---

d. Broken springs in torque

coupling.

d. Contact a service

technician.

---

3. No product is being

dispensed.

a. Product frozen-up in

freezing cylinder.

a. See problem No. 1. ---

4. Freezer will not operate in

the BEATER or AUTO

mode.

a. Unit is unplugged. a. Check the plug at wall

receptacle.

---

b. Blown fuse, or the circuit

breaker is off.

b. Replace the fuse or turn

the breaker on.

---

c. Beater motor is out on

overload. Check fault

description screen.

c. Allow the motor to cool.

Press the AUTO key. Call

a service technician if the

beater motor goes out on

overload again.

18

5. No compressor operation

in the AUTO mode.

a. Beater motor is out on

overload. Check the fault

description screen.

a. Allow the motor to cool.

Press the AUTO key. Call

a service technician if the

beater motor goes out on

overload again.

18

b. The torque coupling is

bound in the COLD

position.

b. Contact a service

technician.

---

c. Condenser dirty, A/C. c. Clean condenser monthly. 38

d. Water supply off, W/C. d. Turn the water on. ---

41

Models 345, 346, 349, 355 Troubleshooting Guide

PROBLEM PROBABLE CAUSE REMEDY PAGE

REF.

6. Unable to remove the

drive shaft from the rear

shell bearing.

a. Rounded corners of hex

end of drive shaft, drive

coupling, or both.

a. Replace the drive shaft, or

call a service technician to

replace the direct drive

unit.

---

b. Lubrication of hex end of

drive shaft.

b. Do not lubricate the hex

end. If necessary, contact

a service technician for

removal.

24

7. Excessive loss of CO2.a. Leak in the CO2system. a. Contact a service

technician.

---

8. Leakage from rear drip

pan(s) into front drip tray.

a. Seal or o-ring on drive

shaft is worn, missing, or

incorrectly installed.

a. Replace or install correctly

on drive shaft.

24

b. Worn rear shell bearing. b. Contact a service

technician to replace rear

shell bearing.

---

9. Excessive mix leakage

from door spout.

a. Inadequate lubrication of

draw valve o-rings.

a. Lubricate properly. 26

b. Wrong type lubricant on

draw valve o-rings.

b. Use food grade lubricant

(example: Taylor Lube

HP).

24

c. Worn or missing draw

valve o-rings.

c. Replace or install o-rings

on draw valve.

26/ 42

10. Unable to adjust brix. a. Syrup lines need to be

cleaned and sanitized.

a. Clean and sanitize syrup

lines.

---

b. Blocked flow control. b. Contact a service

technician.

---

11. Lack of syrup being

supplied to machine.

a. Loss of CO2to propel

syrup.

a. Contact a service

technician.

---

b. Clogged or kinked syrup

lines.

b. Sanitize syrup lines

regularly. If kinked, repair

or replace.

---

12. Product does not enter

mix hopper.

a. Machine is not in the

AUTO or PRIME mode.

a. Place the machine in the

AUTO or PRIME mode.

34

b. The mix level float switch

is inoperative.

b. Contact a service

technician.

---

13. Carbonated water or

sulfuric aroma is evident

in the faucet or sewage

system.

a. Faulty check valve in

carbonation system.

a. Call a service technician

to replace the check

valve.

---

42 Models 345, 346, 349, 355Parts Replacement Schedule

Section 9 Parts Replacement Schedule

PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY

Scraper Blade XMinimum

Drive Shaft Seal X

Drive Shaft O-Ring X

Freezer Door O-Ring X

Draw Valve O-Ring X

Door Spout O-Ring X

Hopper Cover O-Ring X

Front Bearing X

Prime Plug O-Ring X

Black Bristle Brush, 1” x 2” Inspect & Replace if

Necessary

Minimum

Double Ended Brush Inspect & Replace if

Necessary

Minimum

White Bristle Brush, 1-1/2” x 2” Inspect & Replace if

Necessary

Minimum

White Bristle Brush, 3” x 7” Inspect & Replace if

Necessary

Minimum

Refer to Parts List on the next page when ordering the above parts.

43

Models 345, 346, 349, 355 Limited Warranty on Equipment

131122

Section 10 Limited Warranty on Equipment

TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS

Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited

warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)

to the original purchaser only.

LIMITED WARRANTY

Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and

service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to

defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,

will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for

the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for

a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed

below and on the reverse (if any) of this document.

Product Part Limited Warranty Period

Soft Serve

Frozen Yogurt

Shakes

Smoothies

Frozen Beverage

Batch Desserts

Insulated shell assembly Five (5) years

Refrigeration compressor

(except service valve)

Five (5) years

Beater motors Two (2) years

Beater drive gear Two (2) years

Printed circuit boards and

Softech controls beginning

with serial number H8024200

Two (2) years

Parts not otherwise listed in

this table or excluded below

One (1) year

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins

ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of

purchase may be required at time of service.

2. This limited warranty is valid only if the Product is installed and all required service work on the Product is

performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are

used.

3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in

the Taylor Operator’s Manual.

4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit.

5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.

LIMITED WARRANTY EXCEPTIONS

This limited warranty does not cover:

1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of

defective parts, replacement parts, or new Products.

2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning

of condensers.

44 Models 345, 346, 349, 355Limited Warranty on Equipment

3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.

4. External hoses, electrical power supplies, and machine grounding.

5. Parts not supplied or designated by Taylor, or damages resulting from their use.

6. Return trips or waiting time required because a service technician is prevented from beginning warranty

service work promptly upon arrival.

7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,

unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including

but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning

supplies.

8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake

or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,

accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or

water supply specification of the Product; or components repaired or altered in any way so as, in the

judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.

9. Any Product purchased over the Internet.

10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the

inadequacy or interruption of electrical service.

11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.

12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will

void this limited warranty.

13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY

NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential

damages, so this limitation may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from

jurisdiction to jurisdiction.

LIMITATION OF WARRANTY

THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS

AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE

REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE

COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL

OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,

PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS

WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED

BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

LEGAL REMEDIES

The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or

complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other

correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or

remedies.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

45

Models 345, 346, 349, 355 Limited Warranty on Parts

131122

Section 11 Limited Warranty on Parts

TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS

Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited

warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally

(the “Parts”) to the original purchaser only.

LIMITED WARRANTY

Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service

as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails

due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service

agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no

charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited

warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions

listed below and on the reverse (if any) of this document.

Part’s Warranty Class Code or Part Limited Warranty Period

Class 103 Parts¹Three (3) months

Class 212 Parts²Twelve (12) months

Class 512 Parts Twelve (12) months

Class 000 Parts No warranty

Taylor Part #072454 (Motor- 24VDC *C832/C842*) Four (4) years

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required

at time of service.

2. This limited warranty is valid only if the Part is installed and all required service work in connection with the

Part is performed by an authorized Taylor distributor or service agency.

3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation

location in the unit of original installation.

4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in

the Taylor Operator’s Manual.

5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.

6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate

Taylor Limited Warranty on freezer or grill equipment.

7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this

limited warranty.

1, 2 Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1

(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor

freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.

46 Models 345, 346, 349, 355Limited Warranty on Parts

LIMITED WARRANTY EXCEPTIONS

This limited warranty does not cover:

1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of

defective Parts, replacement Parts, or new Parts.

2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning

of condensers or carbon and grease buildup.

3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including

the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper

assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but

not limited to the platen and plate, sides of the shroud or top of the shroud.

4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or

in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or

other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials

or cleaning processes not approved for use by Taylor.

5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any

release sheets and clips for the Product’s upper platen assembly.

6. External hoses, electrical power supplies, and machine grounding.

7. Parts not supplied or designated by Taylor, or damages resulting from their use.

8. Return trips or waiting time required because a service technician is prevented from beginning warranty

service work promptly upon arrival.

9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,

unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including

but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning

supplies.

10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake

or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,

accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or

water supply specification of the unit in which a part is installed; or Parts or the units in which they are

installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or

normal wear or deterioration.

11. Any Part purchased over the Internet.

12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the

inadequacy or interruption of electrical service.

13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.

14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is

installed will void this limited warranty.

15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY

NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential

damages, so this limitation may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from

jurisdiction to jurisdiction.

47

Models 345, 346, 349, 355 Limited Warranty on Parts

LIMITATION OF WARRANTY

THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS

AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE

REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE

PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR

INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,

PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS

WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED

BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

LEGAL REMEDIES

The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or

complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other

correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

Section 12 Parts List

+ Available Separately

48

Parts List Models 345, 346, 349 & 355

DESCRIPTION PART

NUMBER

345

QTY.

346

QTY.

349

QTY.

355

QTY.

WARR.

CLASS

REMARKS PARTS

UPDATE

Accumulator A.- Insulated X50261 1103 Prior to J9067375 144

+Accumulator- Suction- Vertical 042134 1103 Prior to J9067375 144

Accumulator- Copper 2” Dia. 10” Long 047062 122 103 345- J9067375/Up, 346- J9072433/Up,

349- J9114879/Up

144

Accumulator A.- Insulated- Left X50138 1103 Prior to J9072433

Accumulator A.- Insulated- Right X50139 1103 Prior to J9072433

Accumulator A.- Insulated- Left X50465 1103 Prior to J9114879

Accumulator A.- Insulated- Right X50468 1103 Prior to J9114879

Accumulator- Copper 2”DIA 13”LG 053377 1103 0355- J9053838/Up

Accumulator A.- Insulated X49506 1103 Prior to J9053838

Bearing- Rear Shell 032511 2242 000

+Guide- Drip Seal 028992 2242 000

+Nut- Brass Bearing 028991 2242 000

+O- Ring 018432 2242 000

+Washer- Bearing Lock 012864 2242 000

Bearing- Unit Rear (1 Pulley) X39162- SER 2221 103 Kit- Includes Retaining Plate- 052131 129

Bearing- Unit Rear (2 Pulley) X39163- SER 2 1 103 Kit- Includes Retaining Plate- 052131 126

Beater Assembly 041182 2242 103

+Blade- Scraper 041103 4484 000

Belt 025633 2 2 000

Belt 033142 2000

Belt 044056 1000

Belt (Rear Bearing Units) 033145 2 1 000

Block- Terminal 2P- L1,L2 039422 121 103 349- J9097086/Up, 355- J8113767

Block- Terminal 2P- L1,L2 039422 1231 103 Prior to: 349- J9097086, 355- J8113767

Blower A. X53725- 27 1 1 103 346- K0066159/Up, 349- K0053129/Up

Clip- Screen- Blower 053720 4 4 103

Housing- Blower- 6 POLE 053728 1 1 103

Motor- Fan 208- 230V 50/60 HZ 053481- 27 1 1 103

Screen- Blower 053729 1 1 103

Wheel- Blower 053726 1 1 103

Blower Assembly X47833- 1 1 103 Prior to: 346- K0066159, 349- K0053129

Capacitor- Run 033047 1 1 103

Housing A.- W/Wheel X30160 1 1 103

Motor- Blower 046536- 1 1 103

49

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Brush- Black Bristle (1” x 2”) 013071 1111 000

Brush- Double Ended 013072 1111 000

Brush- White Bristle 014753 1111 000

Brush- White Bristle (3” x 7”) 023316 1111 000

Cable- Ribbon- 50C (5”) 040040- 010 1103

Cable- Ribbon- 50C (20”) 040040- 011 1111 103

Cable- Ribbon- 20C (18”) 040040- 042 1111 103

Cable- Ribbon- 20C (18”) 040040- 043 1111 103

Cable- Ribbon- 20C (14”) 040040- 041 1103

Cable- Ribbon- 14C (14”) 040040- 015 1103

Cable- Ribbon- 14C (22”) 040040- 019 1 1 1 103

Carbonator 049455- 27 111 103 McCann - J5061557/Up 95, 119

Probe A.- Carbonator w/Reed Switch 050257- 27 111 103 230- 60- 1 103, 119

Carbonator (OLD) 032569 111 103 Jo Bell - Prior to J5061557 95

Card- FCB P.O.P. 043957 1 1 1 000

Card- Flavor (Packet of 9 Cards) 035324 1121 000

Caster- Locking Swivel (Front) 030307 222 103

+Lock- Caster Bracket 032571 222 103

Caster- Swivel (Rear) 021279 222 103

Compressor (COPELAND) 052396- 122 512 345- J9067375/Up 346- J9067641/Up 144

349- J9097086/Up

+Capacitor- Run 35UF/370V 029439 122 103 230- 60- 1 144

+Capacitor- Start 189- 227UF/250V 053106 122 103 230- 60- 1 144

+Relay- Compressor 052401- 27 122 103 230- 60- 1 144

Compressor (BRISTOL) 036880- 1221 512 Prior to: 345- J9067375, 346- J9067641,

349- J9097086, 355- J9053838.

For Service- Use 047520- & the

applicable start components.

140/141

355 - For Service - Use X53905- 27

(Modifications Required - SB 2507)

150

+Capacitor- Run - 25UF/440V 037431 1221 103 230- 60- 1

+Capacitor- Start - 161- 193UF/250V 031790 1221 103 230- 60- 1

+Relay- Start- Compressor 037430 1221 103 230- 60- 1

Compressor (TECUMSEH) 047520- 122 512 Replacement for 036880-

+Capacitor- Run - 35MFD/375V 029439 122 103 230- 60- 1

+Capacitor- Start - 124- 147MFD/330V 048134 122 103 230- 60- 1

+ Available Separately

50

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

+Relay- Start- Compressor 048150 122 103 230- 60- 1

Compressor (COPELAND) 051958- 1512 J9053838/Up - HP62 Also replacement for

036880- Must convert to HP62 Refrigerant

& install 049154 Dryer. See Update 142

142

+Box A.- Cap/Relay X53292- 27 1103 230- 60- 1 - J9053838/UP 142

+Capacitor- Start - 189- 227UF/330V 033044- 1 1103 230- 60- 1

+Relay- Start- Compressor 051957- 27 1103 230- 60- 1

INCLUDES:

+Capacitor- Run - 20UF/440V 012906 1103 230- 60- 1

Condenser- AC- 12LX18HX3.12T 5RW 053502- 1 1 1 103 Rear- Left Shell 346- J9072433/Up

349- J9097086/Up

Condenser- AC- 12LX18HX3.12T 5RW 052502- 2 1 1 103 Front- Right Shell 346- J9072433/Up

349- J9097086/Up

Condenser A/C 019558 122 103 Prior to: 346- J9072433 349- J9097086

Condenser A/C 053376 1103 Replaces 047083 139

Coupling A.- Torque X39523 2242 103

Coupling- Drive Torque 046866 2242 103

Coupling- Load Torque 039397 2242 103

Pin- Coupling Torque 039453 6 6 12 6103

Screw- Set 025376 4484 000

Screw- Shoulder 039455 6 6 12 6000

Spring - Red 039734 6 6 12 6103

Label- Identification- Red 049285- RED 2242 000

Cover- Compressor 052816 1 2 103 Sound Barrier - J9067375/Up 144

Cover- Compressor 053290 1103 Sound Barrier - J9053838/Up 142

Cover A.- Mix Tank- Relief Valve X42080 2242 103

Clamp- Hose 042610 2242 000

Cover- Hopper 042079 2242 103

O- Ring- Hopper Cover 016037 2242 000

Tube- Vinyl Drain 020944- 24 2242 000 Bulk under R30335

Valve- Pressure Relief 039365 2242 103

Decal- Cleaning Instructions 039416 1111 000

Decal- Left Control 043636- L 1 1 1 000 Prior to: 345- J9053838 346- J9072433,

355- J9012316

Decal- Left Control 052898 1 1 1 000 345- J9053838/Up, 346- J9072433/Up,

355- J9012316/Up

142

51

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Decal- Right Control 043636- R 1 1 1 000

Decal- Dec- Taylor Domed 053761 1111 000 345- K0012597/Up, 346- K0024873/Up,

349- K0025070/Up, 355- K0013505/Up

Decal- Decorative 045967 1 1 1 000 (Dec Plate- X44115- BLA) J8060000 to:

345- K0012597, 346- K0024873

349- K0025070, 355- K0013505

130

Decal- Decorative ”Taylor Crown/Logo” 043892 1 1 1 000 Prior to J8060000

Decal- Dec- Slush- Press- 4 BRL 053646 1000 349- J6114233/Up

Decal- Decorative 043467 1000 Prior to J9114233

Decal- Power Switch 042941 1111 000

Decal- Pressure Gauge (Set of 4) 039463 1121 000

Decal- Troubleshooting 038374 1111 000

Deflector- Blower Exhaust 046586 1 1 103 Prior to: 346- J9072433, 346- J9071741

Deflector A.- Air Exhaust *346* X53549 1103 J9072433/Up

Deflector A.- Air Exhaust *349* X53593 1103 J9071741/Up

Diagram- Wiring 053515- 1000 J9067375/Up 144

Diagram- Wiring 044939- 1000 Prior to J9067375 144

Diagram- Wiring *346* 053566 1000 J9072433/Up

Diagram- Wiring 044940- 1000 Prior to J9072433

Diagram- Wiring *349* 053636- 1J9114233/Up

Diagram- Wiring 043502S- 1000 Prior to J9114233

Diagram- Wiring 052840- 1000 355- J8113767/Up 142

Diagram- Wiring 044107- 1000 Prior to J9053838

Display- Liquid Crystal X38062- SER 1111 103

+Lens- Display 038221 1111 103

Door- Freezer 039573 2242 103

+Bearing- Front 039349 2242 000

+Handle- Draw Valve 046192- BLA 2242 103 J8060000/Up 130

+Handle- Draw Valve 046192 2242 103 Prior to J8060000

+O- Ring 017003 2242 000

+Screw 053869 4484 000 151

+Slide- Draw Handle 046193- BLA 4484 103 J8060000/Up 130

+Slide- Draw Handle 046193 4484 103 Prior to J8060000

+Spout- Door 046190- BLA 2242 103 J8060000/Up 130

+Spout- Door 046190 2242 103 Prior to J8060000

+ Available Separately

52

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

+Cap 046191- BLA 2242 103 J8060000/Up 130

+Cap 046191 2242 103 Prior to J8060000

+Nut- Spout 039323 2242 103

+O- Ring 039219 4484 000

+Pin- Pivot 039321 2242 103

+Spring 039320 2242 103

+Valve- Draw 039324 2242 103

+O- Ring 016369 4484 000

Dryer- Filter 049154 1000 J8124526/Up 144

Dryer- Filter 046138 1 2 1 000 Prior to: 345- J8124526, 349- J90097086,

355- J9012316

144

Dryer- Filter- HP62- 3/8 X 1/4S 048901 2000 346- J9067641/Up

Dryer- Filter 045866 2000 Prior to J9067641

Dryer- Filter 049154 2 1 000 349- J9097086/Up, 355- J9012316/Up 142

Filter- Air- 18.00LX16.50HX.70W 052779- 1 2 2 000 346- J9072433/Up, 349- J9097086/Up

+Cover- Hole- Filter- Snap In 053801 2 2 000

Filter- Corcom 040140- 001 1111 103

Filter- Water 1/4FFLINX1/4MFLOV 053697 111 000 345- J9102846/Up, 346- J9102432/Up

349- J9102424/Up

Filter- Water (Carbonator) 044734 111 000 Prior to: 345- J9102846, 346- J9102432,

349- J9102424

Filter A.- Regulator X35019 1 1 103 Prior to: 345- J9067375, 346- J9067641 144

Filter- Water Line 029235 1 1 000

Fitting 3/8 x 1/4 018466 1 1 103

Gauge- Pressure (0 - 100 PSI) 043643 1 1 103

Regulator (0 - 100 PSI) 043638 1 1 103

Filter A.- Regulator X42151 1103 Prior to J9114233

Filter- Water Line 029235 1000

Fitting 3/8 x 1/4 018466 1103

Gauge- Pressure (0 - 100 PSI) 043643 1103

Regulator (0 - 100 PSI) 043638 1103

Flow Control - w/o Pressure Switch X48728- 27 2242 103 Less Pressure Switch

Body A.- Flow Control w/Solenoid X48729- 27 2242 103

(Or X48729- SER - Body A.- Flow Control

w/o Solenoid)

224 103

+Body A.- Flow Control - Less Solenoid X48729- SER 2242 103

53

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Coil- Solenoid 048776- 27 4484 103

Retainer- Inlet Line 048829 2242 103

Screw-8x1/2SLHex 048709 30 24 48 24 000

Bowl A.- Float- Flow Control X48732 2242 103

Clip- Retainer- Syrup Pressure Switch 048710 4242 103

O- Ring- Flow Control Float A. 016137 4484 000

Retainer- Inlet Line 048829 2242 103

Screw-8x1/2SLHex 048709 30 12 24 12 000

Screw- 8- 32 x 3/8 Hex 041951 4484 000

+Switch- Pressure 35 PSI 048784 2242 103

+Switch- Pressure 15 PSI 049706 2442 103 non- pressurized units only

+Plug- Pressure Switch 049573 2242 103 non- pressurized units only

+O- Ring- Plug 016137 2242 000 non- pressurized units only

Fuse 15 Amp - In Line 045293 1121 000

+Holder- Fuse 045606 1121 103

Guide A.- Drip Pan X47134 1 1 103

Guide A.- Drip Pan X47137 1103

Harness A.- Feed X49312 1 1 103

Adaptor- Swivel 016715 4 4 103

Label- CO2 044519 2 2 000

Ferrule 052140 6 6 000

Fitting 049427 2 2 103

Hose- Beverage 051826- 146 1 1 000 Bulk - R30313 128

Hose- Beverage 051826- 155 1 1 000 Bulk - R30313

Hose- Beverage 051826- 168 1 1 000 Bulk - R30313

Marker- No. 1 018520 2 2 000

Marker- No. 2 018521 2 2 000

Valve- Check 030386 2 2 103

Washer- Nylon Flare 018595 2 2 000

Harness A.- Feed X52457 1103 J8050000/Up (Replaces X49313) 130

Adaptor- Swivel 016715 6103

Marker- No. 1 018520 2000

Marker- No. 2 018521 2000

Marker- No. 3 018522 2000

Marker- No. 4 018523 2000

+ Available Separately

54

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Washer- Nylon Flare 018595 4000

Ferrule 052140 10 000

Valve- Check 030386 4103

Hose- Beverage 051826- 180 4000 Bulk - R30313 128

Hose- Beverage 051826- 210 1000

Label- CO2 044519 2000

Fitting 049427 4103

Harness A.- Feed X51823 1103

Adaptor 018646 1103

Adaptor- Swivel 016715 8103

Decal- Soda 045199 3000

Elbow 049428 2103

Ferrule 021030 14 000

Hose- Beverage 051826- 120 3000 Bulk - R30313 128

Hose- Beverage 051826- 188 2000

Hose- Beverage 051826- 8 2000

Marker- No. 1 018520 3000

Marker- No. 2 018521 3000

Marker- No. 3 018522 2000

Marker- No. 4 018523 2000

Tee 019762 1103

Valve- Check 030386 2103

Valve- Check 049429 2103

Washer- Nylon Flare 018595 4000

Hood 044618 1 1 1 103

Hood 042166 1103

Kit A.- Tune- Up X39699 2242 000

Bearing- Front 039349 2242 000

O- Ring (Door Spout) 039219 4484 000

O- Ring (Draw Valve) 016369 4484 000

O- Ring (Drive Shaft) 025307 2242 000

O- Ring (Freezer Door) 017003 2242 000

O- Ring (Hopper Cover) 016037 2242 000

O- Ring (Prime Plug) 029751 4484 000

O- Ring Removal Tool 048260- WHT 1242 000

55

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Seal (Drive Shaft) 032560 2242 000

Label- Caution- GRD- PERM- ENG/SP 032164 111 000 346- J9084947/Up, 349- J9097086/Up,

355- J9012316/Up

Label- Door- Warning- Moving Parts 032749 1111 000 *CAUTION*

Label- Warning- Cover 051433 7875 000 Replaces 036529 Decal

Label- Warning- Do Not Draw Product 042279 2222 000 w/Light Flashing 349- 4 prior to J8124111

Label- Warning- Relieve Pressure 039462 2222 000 To Prevent Injury 349- 4 prior to J8124111

LED Assembly (Product Not Ready) 051807 1121 103 New Amber Light (Replaces X42508) 136

Leg- 4” 036397 4103

+Cap- Rubber 039268 4000

Lens- Yellow 051751 1242 103 LED Snap In - Replaces 042509- Lens-

Red

Line A.- Air Supply X28150 1103

Adaptor- Swivel 016715 2103

Ferrule 052140 2000

Hose- Beverage 051826- 65 1000 Bulk - R30313 128

Line A.- CO2 (Regulator to Carbonator) X44952 1 1 103

Adaptor- Swivel 016715 2 2 103

Label- CO2 044519 2 2 000

Ferrule 052140 2 2 000

Hose- Beverage 051826- 24 1 1 000 Bulk - R30313 128

Line A.- CO2 (Regulator to Carbonator) X44518 1103

Adaptor- Swivel 016715 2103

Ferrule 052140 2000

Hose- Beverage 051826- 50 1000 Bulk - R30313 128

Line A.- CO2 (Right & Left) (NEW) X53880 2 2 2 103 Use w/New Style 3.5 Quart Mix Tank 151

Adaptor- Swivel 016715 4 4 4 103

Ferrule 052140 4 4 4 000

Hose- Beverage 051826- 8 2 2 2 000 Bulk- R30313

Line A.- CO2 (Right & Left) (OLD) X43656 2 2 2 103 Use w/Old Style 2.5 Quart Mix Tank 151

Ferrule 052140 4 4 4 000

Hose- Beverage 051826- 9 2 2 2 000 Bulk - R30313 128

Line A.- CO2 (No. 1) X52453 1103 J8050000/Up (Replaces X45182) 130

Adaptor- SWV 1/4F 1/4Barb*SS* 016715 2103

Ferrule 052140 2000

Marker- No. 1 018520 2000

+ Available Separately

56

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Hose- Beverage 051826- 30 1000 Bulk - R30313 (Replaces 051826- 14) 128/130

Line A.- CO2 (No. 2) X52454 1103 J8050000/Up (Replaces X45183) 130

Adaptor- SWV 1/4F 1/4Barb*SS* 016715 2103

Ferrule 052140 2000

Marker- No. 2 018521 2000

Hose- Beverage 051826- 27 1000 Bulk - R30313 (Replaces 051826- 9) 128/130

Line A.- CO2 (No. 3) X52455 1103 J8050000/Up (Replaces X45184) 130

Adaptor- SWV 1/4F 1/4Barb*SS* 016715 2103

Ferrule 052140 2000

Marker- No. 3 018522 2000

Hose- Beverage 051826- 28 1000 Bulk - R30313 (Replaces 051826- 8) 128/130

Line A.- CO2 (No. 4) X52456 1103 J8050000/Up (Replaces X45185) 130

Adaptor- SWV 1/4F 1/4Barb*SS* 016715 2103

Ferrule 052140 2000

Marker- No. 4 018523 2000

Hose- Beverage 051826- 29 1000 Bulk - R30313 (Replaces 051826- 4) 128/130

Line A.- CO2 (CO2 Tank to Syrup Tank) X31565 2242 103

Adaptor- Swivel 016715 4484 103

Ferrule 052140 4484 000

Hose- Beverage 051826- 36 2242 000 Bulk - R30313 128

Line A.- CO2- BIB Pump X41005 2 2 103

Ferrule 052140 2 2 000

Hose- Beverage 051826- 36 2 2 000 Bulk - R30313 128

Line A.- Mix Outlet (Left) X49585 1 1 103

Elbow- 1/4 FFL x 1/4 Barb 020563 1 1 103

Elbow- 3/8 O- Ring x 1/4 Barb 049428 1 1 103

Ferrule 052140 4 6 000

Hose- Beverage 051826- 3 1 1 000 Bulk - R30313

Hose- Beverage 051826- 32 1 1 000 Bulk - R30313

Hose- Beverage 051826- 40 1 1 000 Use w/Old Style 2.5 Quart Mix Tank 151

Hose- Beverage 051826- 42 1 1 000 Use w/New Style 3.5 Quart Mix Tank 151

Marker- No. 1 018520 2 2 000

Tee- 1/4 Barb- SS 019762 1 1 103

Valve- Sampling 031622 1 1 103

Line A.- Mix Outlet (Left & Right) X49667 2103

57

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Elbow- 1/4 FFL x 1/4 Barb 020563 2103

Elbow- 3/8 O- Ring x 1/4 Barb 049668 2103

Ferrule 052140 8000

Hose- Beverage 051826- 24 2000

Hose- Beverage 051826- 46 2000 Use w/New Style 3.5 Quart Mix Tank

Hose- Beverage 051826- 40 2000 Use w/Old Style 2.5 Quart Mix Tank

Valve- Sampling 031622 2103

Line A.- Mix Outlet (Right) X49586 1 1 103

Elbow- 1/4 FFL x 1/4 Barb Swivel 020563 1 1 103

Elbow- 3/8 O- Ring x 1/4 Barb SS 049428 1 1 103

Ferrule 052140 6 6 000

Hose- Beverage 051826- 3 1 1 000

Hose- Beverage 051826- 32 1 1 000

Hose- Beverage 051826- 42 1 1 000 Use w/New Style 3.5 Quart Mix Tank 151

Hose- Beverage 051826- 40 1 1 000 Use w/Old Style 2.5 Quart Mix Tank 151

Marker- No. 2 018521 2 2 000

Tee- 1/4 Barb SS 019762 1 1 103

Valve- Sampling 031622 1 1 103

Line A.- Mix Outlet (No. 1) X49719 1103

Elbow- 1/4 FFL x 1/4 Barb 020563 1103

Elbow- 3/8 O- Ring x 1/4 Barb 049428 1103

Ferrule 052140 6000

Hose- Beverage 051826- 5 1000

Hose- Beverage 051826- 38 1000 Use w/New Style 3.5 Quart Mix Tank 151

Hose- Beverage 051826- 36 1000 Use w/Old Style 2.5 Quart Mix Tank 151

Hose- Beverage 051826- 48 1000

Marker- No. 1 018520 2000

Tee 019762 1103

Valve- Sampling 031622 1103

Line A.- Mix Outlet (No. 2) X49720 1103

Elbow- 1/4 FFL x 1/4 Barb 020563 1103

Elbow- 3/8 O- Ring x 1/4 Barb 049428 1103

Ferrule 052140 6000

Hose- Beverage 051826- 3 1000 Use w/Old Style 2.5 Quart Mix Tank

Hose- Beverage- 1/4 ID X 7/16 OD 051826- 5 1000 Use w/New Style 3.5 Quart Mix Tank

+ Available Separately

58

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Hose- Beverage 051826- 48 1000 Use w/Old Style 2.5 Quart Mix Tank 151

Hose- Beverage 051826- 50 2000 Use w/New Style 3.5 Quart Mix Tank 151

Marker- No. 2 018521 1000

Tee- 1/4 Barb SS 019762 1103

Valve- Sampling 031622 1103

Line A.- Mix Outlet (No. 3) X49721 1103

Elbow- 1/4 FFL x 1/4 Barb 020563 1103

Elbow- 3/8 O- Ring x 1/4 Barb 049428 1103

Ferrule 052140 6000

Hose- Beverage 051826- 5 1000

Hose- Beverage 051826- 48 1000 Use w/Old Style 2.5 Quart Mix Tank 151

Hose- Beverage 051826- 50 2000 Use w/New Style 3.5 Quart Mix Tank 151

Marker- No. 3 018522 2000

Tee 019762 1103

Valve- Sampling 031622 1103

Line A.- Mix Outlet (No. 4) X49722 1103

Elbow- 1/4 FFL x 1/4 Barb 020563 1103

Elbow- 3/8 O- Ring x 1/4 Barb 049428 1103

Ferrule 052140 6000

Hose- Beverage 051826- 5 1000

Hose- Beverage 051826- 38 1000 Use w/New Style 3.5 Quart Mix Tank 151

Hose- Beverage 051826- 36 1000 Use w/Old Style 2.5 Quart Mix Tank 151

Hose- Beverage 051826- 48 1000

Marker No. 4 018523 2000

Tee 019762 1103

Valve- Sampling 031622 1103

Line A.- Pressure (Water) X44961 1 1 103 Prior to: 345- J9067375, 346- J9056262 144

Adaptor- Barb 018646 1 1 103

Adaptor- Swivel 016715 1 1 103

Ferrule 052140 2 2 000

Hose- Beverage 051826- 63 1 1 000

Line A.- Soda (Carbonator- Sentry) X49587 1 1 103

Adaptor- Swivel 016715 3 3 103

Decal- Soda 045199 3 3 000

Ferrule 052140 6 6 000

59

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Hose- Beverage 051826- 28 1 1 000

Hose- Beverage 051826- 30 2 2 000

Tee 019762 1 1 103

Valve- Check 049429 2 2 103

Washer- Nylon 018595 2 2 000

Line A.- Water (Pump Discharge) X49485 1 1 103

Elbow 049464 2 2 103

Ferrule 029834 2 2 000

Hose- Beverage 020565- 28 1 1 000 Bulk - R30333

Line A.- Water (Pump Discharge) X49465 1103

Elbow 049464 2103

Ferrule 029834 2000

Tube- Nylobrade 020565- 24 1000

Line A.- Water (Pump Inlet) X44953 1 1 103 Prior to: 345- J9067375, 346- J9055262 144

Adaptor 019194 2 2 103

Ferrule 029834 2 2 000

Tube- Nylobrade 020568- 86 1 1 000

Line A.- Water (Pump Inlet) X42219 1103 Prior to J9102424

Adaptor 019194 2103

Ferrule 029834 2000

Tube- Nylobrade 020565- 20 1000

Line A.- Water- Regulator X53386 1 1 103 345- J9067375/Up, 346- J9067641/Up 144

Adaptor- Swivel- 3/8F x 3/8 Barb 019194 1 1 103

Ferrule 029834 6 6 000

Fitting- 3/8MFL x 3/8 Barb 053503 1 1 103

Hose- Beverage 020565- 3 1 1 000 Bulk R30333

Tube- Nylobrade 020565- 38 1 1 000 Bulk R30333

Hose- Beverage 020565- 50 1 1 000 Bulk R30333

Regulator- Water 30 PSI Fixed 051729 1 1 103

Tee- 3/8 Barb x 1/4MFL x 3/8 Barb 038582 1 1 103

Line A.- Water *349*REG. X53645 1103 J9114233/Up

Adaptor- SWV 3/8F X 3/8arb*SS* 019194 1103

Ferrule- .650 ID NP Brass 029834 6000

Fitting- 3/8MFL X 3/8Barb- Brass 053503 1103

Hose- Beverage- 3/8 ID X 5/8 OD 020565- 16 1000 Bulk R30333

+ Available Separately

60

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Hose- Beverage- 3/8 ID X 5/8 OD 020565- 38 1000 Bulk R30333

Hose- Beverage- 3/8 ID X 5/8 OD 020565- 8 1000 Bulk R30333

Regulator- Water- 30 PSI Fixed 051729 1103

Tee- 3/8 BARBX1/4MFLX3/8BARB- SS 038582 1103

Lubricant- Taylor 048232 1111 000

Manifold A.- CO2 - 2 Regulators - 2 Solenoids X51834- 27 1 1 103 J8040000/Up 128

Elbow- 1/4MFL X 1/8MPT Brass 005139 3 3 103

Manifold- CO2 - 2 Regulator - 2 Solenoid 051835- 27 1 1 103

Gauge- 60 PSI - 1/8 MPT- Back Mount 027875 1 1 103

Gauge- 100 PSI - 1/8 MPT- Back Mount 052699 1 1 103

Regulator- 60 PSI 051835- 4 1 1 103 136

Regulator- 20 PSI 051835- 3 1 1 103 136

Coil- Service- CO2 Manifold 051835- 2 2 2 103 136

+ Kit- Service- Valve & Coil 051835- 1 2 2 103 Includes: Plunger Tube, Nut, Coil &

Bracket, Spring, Plunger & O- Ring

136

Valve- Check - 1/4MPT In X 1/4MFL Out 044534 2 2 103

Manifold A.- CO2 - 2 Regulator- 4 Solenoid X51838- 27 1103 J8054096/Up (Repl X47223- 27 Sol) 129

Elbow- 1/4MFL X 1/8MPT Brass 005139 2103

Fitting- 1/4MFL X 1/8MPT 001485 1103

Manifold- CO2- 2Reg/4Sol*349* 051839- 27 1103

Coil- Service- CO2 Manifold 051835- 2 4103 136

Gauge- 60 PSI- Back Mount 027875 1103 136

Gauge- 100 PSI- Back Mount 052699 1103

Regulator- 60 PSI 051835- 4 1103

Regulator- 20 PSI 051835- 3 1103

+ Kit- Service- Valve & Coil 051835- 1 4103 Includes: Plunger Tube, Nut, Coil &

Bracket, Spring, Plunger & O- Ring

136

Valve- Check 1/4MPTINX1/4MFLOUT 044534 4103

Valve- Check- 1/4MPT In X 1/4MFL Out 044534 4103

Manifold- CO2- 2 Regulator - 4 Solenoid 051839- 27 1103

Manifold A.- CO2 - 1 Regulator - 2 Solenoid X51832- 27 1103 J8040000/Up 129

Elbow- 1/4MFL X 1/8MPT Brass 005139 2103

Manifold- CO2- 1 Regulator - 2 Solenoids 051833- 27 1103

Coil- Service- CO2 Manifold 051835- 2 2103 136

Gauge- 60PSI- 1/8 MPT- Back Mount 027875 1103 136

61

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Regulator- 20 PSI 051835- 3 1103 136

+ Kit- Service- Valve & Coil 051835- 1 2103 Includes: Plunger Tube, Nut, Coil &

Bracket, Spring, Plunger & O- Ring

136

Valve- Check - 1/4MPT In X 1/4MFL Out 044534 2103

Manifold A.- Soda w/Check Valve X49718 1103

Adaptor- Swivel 016715 5103

Adaptor- 1/8 MP x 1/4 Barb 020130 1103

Ferrule 052140 10 000

Fitting- 3/8 O- Ring x 1/4 Barb SS 049427 4103

Hose- Beverage 051826- 19 1000

Hose- Beverage 051826- 23 2000

Hose- Beverage 051826- 26 2000

Manifold A.- Soda X42342 1103

Valve- Check 042352 4103

Washer- Flare Nylon 018595 4000

Man- Oper 345/346/349/355 039710- M 1111 000

Motor- Beater 014477- 2 2 212

Motor- Beater 033140- 2 1 212

Motor-Fan50Watt 029770- 1103 J9067375/Up 144

+Blade- Fan (12” Pull) 53419 1103 J9067375/Up 144

Motor- Fan - 120 Watt 041401- 1103 Prior to J9067375 144

+Blade- Fan (12” Pull) 047061 1103 Prior to J9067375 144

+Capacitor- Run - 4UF- 370V 019624 1103 Fan Motor - Prior to J9067375 144

Motor- Fan - 50 Watt 029770- 1103 J9053838/Up 142

+Blade- Fan (12” Push) 049009 1103 J9053838/Up 142

Motor- Fan - 80 Watt 051744- 1103 J8010000 thru J9053837

+Blade- Fan (12” Push) 047279 1103

+Capacitor- Run - 4UF- 440V 051785 1103 Fan Motor (208- 230/60/1)

Motor- Fan - 120 Watt 041401- 1103 Prior to J8010000

+Blade- Fan (12” Push) 047060 1103

+Capacitor- Run - 4UF- 370V 019624 1103

Motor- Pump 016309- 111 103

Nut- Stud 043666 8 8 16 8103

Pail (10 qt. - 9.5 liter) 013163 1111 000

Pan- Drip (Expansion Valve) 044949 1 1 103

+ Available Separately

62

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Pan- Long Black Drip 19- 1/2 in Long 035034 1 1 1 103 Rear Shell Bearing

Pan- Rear White Drip 043612 1 1 1 103 Drip Guide

Pan A.- Drip w/Hose (Left) X42201 1103 Rear Shell Bearing

Pan A.- Left Drip X42202 1103 Rear Shell Bearing

Tube- Vinyl Drain 020944- 11 1000

Pan A.- Drip w/Hose (Right) X42203 1103 Rear Shell Beariing

Pan A.- Right Drip X42204 1103 Rear Shell Bearing

Tube- Vinyl Drain 020944- 11 1000

Pan A.- Drip (Expansion Valve) X50226 1103

Panel- Front Lower 043599- BLA 1 1 103 J8060000/Up 130

Panel- Front Lower 043599 1 1 103 Prior to J8060000

Panel- Front- Lower 042082- BLA 1103 J8110000/Up

Panel- Front Lower 042082- WHT 1103 Prior to J8110000

Panel- Front Lower 043599SBLA 1103 J8060000/UP 130

+Plug- Hole- 1/2- Black 049775 2000

Panel- Front Lower 043599- SP 1103 Prior to J8060000

Panel- Front Upper 043600- BLA 1 1 1 103 J8060000/Up, 355J9024482/Up 130

Panel- Front Upper 043600 1 1 1 103 Prior To J8060000

Panel- Front Upper 042081- BLA 1103 J8110000/Up

Panel- Front Upper 042081- WHT 1103 Prior to J8110000

Panel- Rear 044921- SP1 1 1 103

Panel- Rear *349*Drain Hole* 042198 1103 J9114240/Up

Panel A.- Rear X42197 1103 Prior to J9114240

Panel- Rear 044621- SS 1103

Panel- Service 044916 1103

Panel- Service *346* Filter 053612 1103 Air cooled only - J9072433/Up

Panel- Service 045125 1103 Water cooled and A/C prior to J9072433

Panel- Service *349*AC* 053652 1103 Air cooled only J9114233/Up

Panel- Service 042293 1103 Water cooled and A/C Prior to J9114233

Panel A.- Left Side X45136 1103

Panel A.- Left Side X44917 1103

Panel A.- Left Side X42289 1103

Panel- Left Side 044619- SP 1103

Panel A.- Side *346*AC*R*Filter X53611 1103 Air cooled only - J9072433/Up

Panel A.- Right Side X44919 1 1 103 Water cooled and A/C prior to J9072433

63

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Panel A.- Right Side X42291 1103

Panel- Right Side 044620- SP 1103

PCB A.- Brown Out X47299- SER 1111 103

PCB A.- Control *345* UVC2 (CURRENT) X53580- SER 1212 J9067375/Up 144

PCB A.- UVCA (Base Board) X51169- SER 1212

Chip- Software UVC2 Display X40872 1103

Chip- Software UVC2 Chip- SEL X40873 1103

Chip- Software UVC2 U10 English X40875 1103

Chip-SoftwareUVC2U11 X40876 1103

Chip- Software X40790 1103 J9067375/Up

PCB A.- Control *345* UVC2 (OLD STYLE) X52440- SER 1212 J8072717 thru J9067374 132/144

PCB A.- UVC2 (Base Board) X51169- SER 1212 J8072717/UP 132

Chip- Software (Old) X40878 1103 J8072717 thru J9067374 132

PCB A.- Control (OLD STYLE) X47235- SER 1212 Use X52440- SER 132

PCB A.- Universal (Base Board/Old) X44863- SER 1212 Prior to J8072717 132

Chip- Software/Old X40837 1103 Prior to J8072717 132

PCB A.- Control *346*UVC2 (CURRENT) X53517- SER 1212 J9067641/Up 145

PCB A.- Universal (Base Board) X51169- SER 1212 J9067641/Up 145

Chip- Software UVC2 Display X40872 1 1 103

Chip- Software UVC2 Chip- SEL X40873 1 1 103

Chip- Software UVC2 U10 English X40875 1 1 103

Chip-SoftwareUVC2U11 X40876 1 1 103

Chip- Software X40789 1103 J9067641/Up 145

PCB A.- Control (OLD STYLE) X47233- SER 1212 Use X53517- SER 145

PCB A.- Universal (Base Board) X44863- SER 1212 Prior to J9067641 145

Chip- Software X40838 1103 Prior to J9067641 145

PCB A.- Control (CURRENT) X53653- SER 1212 J9114233/Up 148

PCB A.- Universal (Base Board) X51169- SER 1212 J9114233/Up 148

Chip- Software UVC2 Display X40872 111 103

Chip- Software UVC2 Chip- SEL X40873 111 103

Chip- Software UVC2 U10 English X40875 111 103

Chip-SoftwareUVC2U11 X40876 111 103

Chip- Software X40791 1103 J9114233/Up 148

IC- Parallel Port Chip 040176- 006 1103

PCB A.- Control (OLD STYLE) X45315- SER 1212 Use X53653- SER 148

+ Available Separately

64

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

PCB A.- Universal (Base Board) X44863- SER 1212 Prior to J9114233

Chip- Software X40833 1103 Prior to J9114233

PCB A.- Control *355- 355A UVC2*(CURRENT) X52846- SER 1212 J9053838/Up 142

PCB A.- UVC2 (Base Board) X51169- SER 1212 J8072560/Up

Chip- Software UVC2 Display X40872 1111 103

Chip- Software UVC2 Chip- SEL X40873 1111 103

Chip- Software UVC2 U10 English X40875 1111 103

Chip-SoftwareUVC2U11 X40876 1111 103

Chip- Software- 355- 355A UVC2 X40781 1103 J9053838/Up 142

PCB A.- Control *355*UVC2 (OLD STYLE) X52439- SER 1212 Use Prior to J9053838

(Replaces X47234- SER)

132/142

PCB A.- UVC2 (Base Board) X51169- SER 1212 J8072560/Up 132

Chip- Software X40877 1103 J8072560 thru J9053837 132/142

PCB A.- Control (OLD STYLE) X47234- SER 1212 Use X52439- SER 132

PCB A.- Universal (Base Board) X44863- SER 1212 Prior to J8072560 132

Chip- Software X40839 1103 Prior to J8072560 132

PCB A.- Interface X45622- SER 1121 212

Plate- Decorative 035410- BLA 1103 J8110000/Up

Plate- Decorative (Cover w/Slots for Flavor

Cards)

035410 1103 Prior to J8110000 (White)

Plate- Dec- 345- 346- 355*BLACK 043639- BLA 1 1 1 103 345- J9125292/Up, 346- J9113331/Up,

355- J9024482/Up

Plate A.- Decorative X44115- BLA 1 1 1 103 J8060000 to: 345- J9125292,

346- J9113331, 355- J9024482

130

Plate A.- Decorative X44115 1 1 1 103 Prior to J8060000

Plug- Prime 039568 2242 103

+O- Ring 029751 4484 000

Probe- Thermistor (Barrel) 038061- BLK 2242 103

Pulley- 11” Dia. (Rear Bearing Unit) 025570 2 2 103

Pulley- 11” Dia. 035955 2 1 103

Pulley (Rear Bearing Unit) 047094 2 1 103

Pulley (Rear Bearing Unit) 047095 2 1 103

Pulley (Beater Motor) 027616 2 2 103

Pulley (Beater Motor) 042190 2 1 103

Pump- Water 016306 1 1 103

65

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Pump- Water 042791 1103

Regulator- CO2 (Wall Mount) 051840 1111 103 Replaces 031623 124, 126

Includes:

Diaphragm 051840- 6 1111 103

Seat Assembly 051840- 7 1111 000

Gauge- Regulator- 160 lb. 051840- 15 2222 103

Gauge- Regulator- 3000 lb. 051840- 16 1111 103

Hose- Regulator- 3 Foot- Hi Pressure 051840- 22 1111 103 Includes Fittings

Ring- Quad- Hose- Regulator- CO2 051840- 22R 1111 000

Relay- Compressor 012725- 1221 103

Sanitizer- Kay 5 041082 1111 000

Sensor A.- EVC X44951 2 2 2 103

Sensor A.- Viscosity No. 1 X47221- 1 1103

Sensor A.- Viscosity No. 2 X47221- 2 1103

Sensor A.- Viscosity No. 3 X47221- 3 1103

Sensor A.- Viscosity No. 4 X47221- 4 1103

Shaft- Beater Drive 039337 2242 103

+Bushing- Drive Shaft Seal 042278 2242 103

+O- Ring 025307 2242 000

+Seal 032560 2242 000

Shelf- Drip Tray 049697 1103

+Screw- Thumb 044403 2000

Shelf A.- Drip Tray X44898 1 1 103

+Tube- Vinyl 020945- 96 1 1 000

Shelf A.- Drip Tray X38355 1103

+Tube- Vinyl 020945- 96 1000

Shell A.- Insulated (NEW) X53756 224 512 345- K0026349/Up, 346- K0024873/Up,

349- K0025070/Up

151

Shell A.- Insulated (OLD) X44905 224 512 Prior to Above Serial Numbers - replace

with X53756 Shell, 053875- 5 or - 8 Feed

tube. 345 & 346 also use X53880 CO2

Line.

151

Shell A.- Insulated (NEW) X53812 2512 3.5 Quart Mix Tank k0038353/Up

Shell A.- Insulated (OLD) X43624 2512 Prior to K0038353 Replace With X53812

Shell, X53880 CO2 Line & 053875- 5 or - 8

Feed Tube

Shield- Splash 043719 1 1 1 103

+ Available Separately

66

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

Shield- Splash 038276 1103

Stud- Nose Cone (Freezing Cylinder) 020445 8 8 16 8103

+Washer- Freezer Stud 036265 8 8 16 8000

Switch- Pressure - 440 PSI 048230 1221 103 345- J9067375/Up, 346- J9072433/Up,

349- J9097086/Up, 355- J9053838/Up

142/144

Switch- Pressure - 440 PSI 046362 1221 103 Prior to: 345- J9067375, 346- J9072433,

349- J9097086, 355- J9053838

144

Switch- Low Pressure Switch (H2O) 016292 1111 103

Switch- Low Pressure Switch (CO2) 036070 1111 103

Switch- Membrane - 20” - Left 044521 1 1 1 103 345- J9067375/Up, 346- 9072433/Up,

355 - J9053838/Up

142/144

Switch- Membrane - 23” - Right 053138 1 1 1 103 345- J9067375/Up, 346J9072433,

355 - J9053838/Up

142/144

Switch- Membrane 038065 2242 103 Prior to: 345- J9067375, 346- J9072433,

355- J9053838

144

Switch A.- Float- Mix Level X44936 2242 103 Mix Hopper

Switch- Toggle- SPST 3/4 HP 250V 012626 1111 103 Power

Transformer 045754 1111 103

Tray- Front Drip 043720- SP 1 1 103

Tray- Front Drip 038275- SP 1103

Tray- Front Drip 043720 1103

Tube- Mix Feed (NEW) 053875- 5 2242 103 New style 3.5 quart mix tank 151

Tube- Mix Feed (OLD) 039566- 5 2242 103 Use w/old style 2.5 quart mix tank 151

Tube- Vinyl (Drip Tray Shelf- Drain Line) 020945- 96 1 1 000

Valve- Access (Compressor) 044455 1 2 1 103

Valve- Access (Compressor) 047016 1221 103 Main High Side 349- Prior to J9114233

Valve- Access (Compressor) 043232 2103 349- Prior to J9114233

Valve- Access- 1/4MFL X 3/8ODSDR 053565 4103 349- J9114233/Up

Valve- Automatic Expansion 046365 2242 103

+Boot- Expansion Valve 050900 2242 000 345- J9067375/Up, 346- J9072433/Up,

349- J9114233/Up, 345- J9012316/Up

+Boot- Expansion Valve 027137 2242 000 Prior to: 345- J9067375, 346- J9072433,

349- J9114233, 355- J9012316

Valve- Check (Defrost Line) 047053 2 4 2 103 Prior to: 345- J906737, 349- J9102431 144

67

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

355 - Prior to J9053838 142

Valve- Solenoid (Liquid Line/Defrost) 043449- 2 4 4 103 J9053838/Up, 355 - 2 Used Prior to

J9053838

142

Valve- Sol 1/8ORF 1/4INX3/8OUT (Defrost) 053511- 2 4 103 346- J9072433/Up, 349- J9114233/Up

Valve- Solenoid (Defrost) 044982- 1221 103 Prior to J9053838, 355 - 1 Used Prior to

J9053838

144

Valve- Solenoid 1/8 ORF X 1/4S 053051- 2J9055971/Up

Valve A.- Solenoid (Regulator/CO2) X44937- 1 1 103 Prior to S/N J8040000 128

+Elbow A.- Restrictor X34866 2 2 103

+Restrictor- Air 021162 2 2 000

+Gauge- Pressure (0- 60 PSI) 021029 1 1 103

+Gauge- Pressure (0- 100 PSI) 043643 1 1 103

+Marker- No. 1 018520 1 1 000

+Marker- No. 2 018521 1 1 000

+Regulator (0- 100 PSI) 043638 2 2 103

+Valve- Check 030386 2 2 103

+Valve- Solenoid 047496- 2 2 103

Valve A.- Solenoid (Regulator/CO2) X47223- 1103 Prior to S/N J8054096 - See Manifold 129

+Gauge- Pressure (0- 60 PSI) 021029 1103

+Gauge- Pressure (0- 100 PSI) 043643 1103

+Manifold A.- CO2 X44508 1103

+Marker- No. 1 018520 1000

+Marker- No. 2 018521 1000

+Marker- No. 3 018522 1000

+Marker- No. 4 018523 1000

+Regulator- CO2 (Primary) 0- 100 PSI 043638 2103

+Valve- Check 044534 4103

+Valve- Solenoid 017444 4103

Valve A.- Solenoid (Regulator/CO2) X45309- 1103 Prior to S/N J8040000 129

+Elbow A.- Restrictor X34866 2103

+Elbow- Union 001486 2103

+Restrictor- Air 021162 2000

+Gauge- Pressure 021029 1103

+Marker- No. 1 018520 1000

+Marker- No. 2 018521 1000

+Regulator (0- 100 PSI) 043638 1103

+ Available Separately

68

Parts List Models 345, 346, 349 & 355

DESCRIPTION PARTS

UPDATE

REMARKSWARR.

CLASS

355

QTY.

349

QTY.

346

QTY.

345

QTY.

PART

NUMBER

+Valve- Check 030386 2103

+Valve- Solenoid 047496- 2103

Video- Train Film- FCB Pressure 046914- V 1111 000 345- J9055921/Up, 346- J9072433/Up,

346- J9072433/Up, 355- J9012316

Washer- Nylon Flare 018595 18 19 519 000

REMOTE DISPENSER ASSEMBLY

Carbonator 049455- 12 1103

Probe A.- Carbonator w/Reed Switch 050257- 12 1103 115 Volt - J7062208/Up 119

Kit A.- Probe & Float 050258- 12 1103 115 Volt - Prior to J7062208

Cord- Power 036408 1103

Elbow- 3/8 FFL x 3/8 Barb 049464 2103

Elbow- 3/8 MFL x 3/8 MPT 007096 1103

Ferrule 029834 2000

Filter- Water 1/4FFLINX1/4MFLOV 053697 1000 Replaces 044734 146, 147

Filter- Water Line 044558 1000

Gauge- Pressure (0- 100 PSI) 043643 1103

Label- Warn- Press (Low Water Pressure) 044108 1000

Label- Water Regulator 044110 1000

Leg- Rubber (Rubber Bumper) 044650 4103

Light- Indicator 017450 1103

Motor- Pump 016309- 12 1103

Panel- Exterior 044805 1103

Pump- Water 016306 1103

Regulator (0- 50 PSI) 029830 1103

Switch- Low Pressure (H2O) 016292 1103

Tube- Nylobrade (Pump to Carbonator Tank) 020565- 14 1000 Bulk R30333

Washer- 3/8 Flare- Nylon 077124 1000

50 CYCLE

Belt 045166 2000

Belt 028182 1000

Capacitor- Run 012906 1 2 1 103 BRISTOL

Capacitor- Start 038143 1 2 1 103 BRISTOL

Capacitor- Run 029439 1 2 103 TECUMSEH & COPELAND

Capacitor- Start 048134 1 2 103 TECUMSEH

69

+ Available Separately

Models 345, 346, 349 & 355 Parts List

DESCRIPTION PART

NUMBER

345

QTY.

346

QTY.

349

QTY.

355

QTY.

WARR.

CLASS

REMARKS PARTS

UPDATE

Capacitor- Run 023606 1103 COPELAND - J9053838/Up 142

Capacitor- Start- 145- 175UF/220V 012901 1 2 COPELAND

Capacitor- Start 051960 1103 COPELAND - J9053838/Up 142

Motor-Fan50Watt 029770- 27 1103 COPELAND - J9053838/Up

Motor- Fan 100 Watt 047178- 34 1 1 103 BRISTOL

+Blade- Fan (12”Pull) 047061 1103

+Blade- Fan (12”Push) 047279 1103

+Capacitor- Run - 4UF/370V 019624 1 1 103 Fan Motor

Pulley (Beater Motor) 037297 1 2 103

Pulley (Beater Motor) 044422 2 1 103

Relay- Start 038146 1 2 1 103 BRISTOL

Relay- Start 048133 1 2 103 TECUMSEH

Relay- Start- Compressor 051957- 12 1 2 COPELAND

Relay- Start 051957- 40 1103 COPELAND - J9053838/Up 142

WATER COOLED

Accumulator- Copper 2”DIA 13”LG 053377 1 2 2/18/99/Up

Blower- 100 CFM 012796- 1103 345- J9071890/Up

Blower Assembly X45116- 111 103

Blower 012796- 111 103

Condenser- WC- Coax 047540 1 1 103 345- J9071890/Up, 349- J9114879/Up

Condenser 048287 1221 103 Repl 018278 (J8050000/Up) 129

Guard- Blower 022505 111 103

Motor- Fan 012768- 1103

+Blade- Fan (7” Push) 016289 1103

Panel- Left Side 044833- SP 1103

Switch- Pressure - 350 PSI 048231 1221 103 345- J9053838/Up, 346- J9071890/Up,

349- J9114879/Up, 355- J9072849

142

Switch- Pressure - 350 PSI 046431 1221 103

Valve- Water 046686 1221 103

345

053515-27

11/12/13

YEL

BLK

YEL

BLK

RED/WHITE

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

BLK

LED

BARREL 2 LED

BARREL 1

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

BRNBRN BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK

W2

BLK

BRN

ORG/WHT

ORN

PRP/WHT

ORG/WHT

BRN

WHT

ORN

ORN

BLK

BLK

WHT/BLK

41 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

YEL

BLK

M

FAN

WHT

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

BLK

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

HPCO

L1

L2

BLK

BLK

WHT/BLK

BLK

WHT

YEL

BLK

WHT

BLK

RED

BLK

BLK

WHT/BLK

BLK/WHT

WHT

WHT/BLK

WHT/BLK

YEL

M

WHT

WHT/BLK

BLK BLK

CARBONATOR FILL SWITCH

WHT

WHT/BLK STRIPE

WHT WHT

WHT

WHT/BLK

WHT/BLK

WHT

C NO C NO

BRN

BLK

BLU

BRN

BLK

BLU

BRN

BLU

RED

RED

BLU

15A FUSE

GROUND FRAME

SECURELY

BARREL

2

DEFROST

RED/WHT

WHT

RED/WHT

WHT

SOLENOID

RED/WHT

WHT

WHT

S

R

LINE

RELAY

START CAPACITOR

C

INTERNAL OVERLOAD

RUN CAPACITOR

COPELAND COMPRESSOR WIRING

1

2

5

4

WHT

BRN

BLK

BRN

052396-1

EQUIPMENT

GROUND

BLEED RESISTOR

WHT(120 VOLTS)

BLK(230 VOLTS)

BLK

BLU

BARREL

1

BLK

BLK

T1 L2

T2

L1

COMPRESSOR

CONTACTOR

COMPRESSOR

CONTACTOR

BLKBLK

MAGNATEK-CENTURY

5

6 1

LEESON

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

T1 OR BLU

T8 OR RED

THERMAL OL

BRN

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN

START

5

1

GE/RBC BEATER MOTOR WIRING

CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5

1

2

3

FIG.1

FIG.2

1 2

1211

PRIMARY

SECONDARY

LEFT BEATER MOTOR

FIG.1

BARREL

1

LIQ. LINE

SOLENOID

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A.

CONTROL

SWITCH

SPST

EMI FILTER

COMPRESSOR

FIG.2

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

123 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

531

W1

RIGHT BEATER MOTOR

FIG.1

PUMP

RUN CAPACITOR USED

WITH 041401-27 OR

047178-34 MOTOR ONLY.

X1

A B

CONT.

TRANS.

1

11

2

12

EMPTY

EMPTY

EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH.

OUT

BRN OUT

PCB A.

IN IN

OUT

345

053515-33

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK STR

BLK

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

BRN

BRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK

W2

BLK

BRN

ORG/WHT

ORN

PRP/WHT

ORG/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

41 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

M

FAN

WHT

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

BLK

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

HPCO

L1

BLK

WHT/BLK

WHT

YEL

BLK

WHT

BLKBLK

BLK

RED

BLK

BLK

BLK

WHT/BLK

5

6 1

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

WHT/BLK

WHT/BLK

YEL

WHT/BLK

BLK/WHT

WHT

WHT

WHT

WHT/BLK

WHT/BLK

L2 L3

BLK

BLK

BLK

BLK

BLK

BLK

BLK

BLK

CNO CNO

WHT

BRN

BLK

BLU

BRN

BLK

BLU

BRN

LED

BARREL 2

BLK/WHT

RED

BLU

LED

BARREL 1

WHT

WHT

BLU

RED

M

BLK BLK

CARBONATOR FILL SWITCH

WHT

GROUND FRAME

SECURELY

15A FUSE

RED/WHT

WHT

WHT

BARREL

1DEFROST

SOLENOID

BARREL

2

RED/WHT

T1

L1

COMPRESSOR

CONTACTOR

L2

T2

COMPRESSOR

CONTACTOR

BLKBLK

1 2

1211

PRIMARY

SECONDARY

LEFT BEATER MOTOR

BARREL

1

LIQ. LINE

SOLENOID

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A.

CONTROL

SWITCH

SPST

EMI FILTER

COMPRESSOR

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1234

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

531

W1

MAGNATEK-CENTURY LEESON

RIGHT BEATER MOTOR

COMPRESSOR

CONTACTOR

L3T3

LINE

COMPRESSOR WIRING

RUN CAPACITOR USED

WITH 041401-27 OR

047178-34 MOTOR ONLY.

X1

A B

PUMP

1

11

2

12

EMPTY

EMPTY

EMPTY - (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH.

COMPRESSOR

TERMINALS

OUT

BRN OUT

PCB A.

IN IN

OUT

CONT.

TRANS.

345

053515-40

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

BLK

LED

BARREL 2 LED

BARREL 1

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

BRNBRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK WHT

W2

BLK

BRN

ORG/WHT

ORN

PRP/WHT

ORG/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

41 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

M

FAN

WHT

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

BLK

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

HPCO

L1

N

WHT

WHT/BLK

WHT

WHT

YEL

BLK

WHT

BLKBLK

BLK

RED

BLK

BLK

GRN/YELGRN/YEL

GRN/YEL

GRN/YEL

GRN/YELGRN/YEL

WHT/BLK

BLK/WHT

WHT

WHT/BLK

WHT/BLK

YEL

M

GRN/YEL

WHT

WHT/BLK

BLK BLK

CARBONATOR FILL SWITCH

WHT

BLK/WHT

WHT

GRN/YEL

GRN/YEL

WHT

WHT

WHT/BLK

WHT/BLK

WHT

C NO C NO

BRN

BLK

BLU

BRN

BLK

BLU

BRN

BLU

RED

RED

BLU

15A FUSE

GROUND FRAME

SECURELY

BARREL

2

DEFROST

RED/WHT

WHT

RED/WHT

WHT

SOLENOID

RED/WHT

WHT

WHT

S

R

LINE

RELAY

START CAPACITOR

C

INTERNAL OVERLOAD

RUN CAPACITOR

COPELAND COMPRESSOR WIRING

1

2

5

4

WHT

BRN

BLK

BRN

052396-1

EQUIPMENT

GROUND

BLEED RESISTOR

WHT(120 VOLTS)

BLK(230 VOLTS)

BLK

BLU

BARREL

1

GRN/YEL

T1 L2

T2

L1

COMPRESSOR

CONTACTOR

COMPRESSOR

CONTACTOR

WHT

BLK

MAGNATEK-CENTURY

5

6 1

LEESON

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

T1 OR BLU

T8 OR RED

THERMAL OL

BRN

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN

START

5

1

GE/RBC BEATER MOTOR WIRING

CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5

1

2

3

FIG.1

FIG.2

1 2

1211

PRIMARY

SECONDARY

LEFT BEATER MOTOR

FIG.1

BARREL

1

LIQ. LINE

SOLENOID

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A.

CONTROL

SWITCH

SPST

EMI FILTER

COMPRESSOR

FIG.2

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

531

W1

RIGHT BEATER MOTOR

FIG.1

PUMP

RUN CAPACITOR USED

WITH 041401-27 OR

047178-34 MOTOR ONLY.

X1

A B

CONT.

TRANS.

1

11

2

12

EMPTY

EMPTY

EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH.

OUT

BRN OUT

PCB A.

IN IN

OUT

346

053566-27

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

BLK

BLK

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

BRN

BRN BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK BLK

W2

BLK

BRN

ORG/WHT

ORN

ORG/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

41 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

BLK

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

LEFT

HPCO

BLK BLK

BLK

WHT/BLK

BLK

WHT

YEL

BLK

WHT

BLKBLK

BLK

RED

BLK

BLK

WHT/BLK

5

6 1

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

WHT/BLK

WHT/BLK

YEL

WHT/BLK

M

BLK BLK

BLK

BLK BLK

M

WHT

BLK

RED/WHT

WHT

WHT

WHT

RED

WHT

BLK/WHT

BLK

BLK

RIGHT

HPCO

WHT/BLK

WHT

BLK

WHT

WHT

BLU/WHT

BRN BLK BLU

BRN BLK BLU

BRN

BRN

LED

BARREL 2

WHT/BLK

RED

BLU

LED

BARREL 1

WHT

WHT

BLU

RED

M

BLK BLK

CARBONATOR FILL SWITCH

WHT

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDING UNIT BEFORE HANDLING SOLID

STATE COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1 AT

EACH END.

RIGHT

COMPRESSOR

CONTRACTOR

RIGHT

COMPRESSOR

FIG.2

RIGHT

COMPRESSOR

CONTRACTOR

GROUND FRAME

SECURELY

15 A

FUSE

S

R

LINE

RELAY

START CAPACITOR

C

INTERNAL OVERLOAD

RUN CAPACITOR

COPELAND COMPERSSOR WIRING - CSR

1

2

5

4

WHT

BRN

BLK

BRN

052396-1

EQUIPMENT

GROUND

BLEED RESISTOR

WHT(120 VOLTS; 220V-50Hz)

BLK(230 VOLTS)

BLK

BLU

L1

L2

BLK

BLK

T1 OR BLU

T8 OR RED

THERMAL OL

BRN

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN

START

5

1

GE/RBC BEATER MOTOR WIRING

CWLE-RED OR T8 INTERNAL ON #5, BLACK OR T5 INTERNAL ON #A}

1

2

3

FIG.1

FIG.2

1 2

1211

PRIMARY

SECONDARY

LEFT BEATER MOTOR

FIG.1

BLOWER

BARREL 1

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

SYR.SOL.

BARREL 1

DEFROST

SOLENOID

4321

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A.

CONTROL

SWITCH

SPST

EMI FILTER

LEFT

COMPRESSOR

FIG.2

LEFT

COMPRESSOR

CONTACTOR

T1 L2

T2

L1

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

J8

W1

1 2 3 4

J7

4321

5 3 1

W1

LEFT

COMPRESSOR

CONTACTOR

MAGNATEK-CENTURY LEESON

RIGHT BEATER MOTOR

FIG.1

T1 L2

T2

L1

COMP.

CONT.

COIL

BARREL 2

DEFROST

SOLENOID

BARREL 2

RUN CAPACITOR

USED WITH 046536-27

MOTOR ONLY

X1

A B

PUMP

1

11

2

12

EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH.

EMPTY

EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04).

CNO CNO

OUT

BRN OUT

PCB A. IN IN

OUT

CONT.

TRANS.

346

053566-33

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

BLK

BLK

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

BLK

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUS

E

DAMAGE TO SOLID STATE COMPO

NENTS.

ELIMINATE STATIC ELECTRICIT

Y BY TOUCHING

GROUNDED UNIT BEFORE HANDLI

NG SOLID STATE

COMPONENTS.

BRNBRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK BLK

W2

BLK

BRN

ORG/WHT

ORN

ORG/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

41 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

BLK

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

LEFT

HPCO

L1

BLK BLK

WHT/BLK

WHT

YEL

BLK

WHT

BLKBLK

BLK

RED

BLK

BLK

BLKBLK

WHT/BLK

5

6 1

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

WHT/BLK

WHT/BLK

YEL

WHT/BLK

M

BLK BLKBLK

BLK BLK

M

WHT

RED/WHT

WHT

WHT

WHT

RED

WHT

BLK/WHT

BLK

BLK

RIGHT

HPCO

WHT/BLK

WHT

BLK

WHT

WHT

BLK

BLU/WHT

L2 L3

BLK

BLK

BLK

BLK

BLK

BLK

BLK

BLK

BLK

BRN

BLK

BLU

BRN

BLK

BLU

BRN

BRN

LED

BARREL 2

BLK/WHT

RED

BLU

LED

BARREL 1

WHT

WHT

BLU

RED

M

BLK BLK

CARBONATOR FILL SWITCH

WHT

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

15 A

FUSE

BLK

BLK

1 2

1211

PRIMARY

SECONDARY

LEFT BEATER MOTOR

BARREL 1

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

SYR.SOL.

BARREL 1

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

GROUND FRAME

SECURELY

J6

CONTROL PCB A.

CONTROL

SWITCH

SPST

EMI FILTER

LEFT

COMPRESSOR

LEFT

COMPRESSOR

CONTACTOR

T1 L2

T2

L1

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

12345678

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

5 3 1

W1

LEFT

COMPRESSOR

CONTACTOR

MAGNATEK-CENTURY LEESON

RIGHT BEATER MOTOR

RIGHT

COMPRESSOR RIGHT

COMPRESSOR

CONTRACTOR

T1 L2T2

L1

RIGHT

COMPRESSOR

CONTRACTOR

COMP.

CONT.

COIL

BARREL 2

DEFROST

SOLENOID

BARREL 2

L3T3

LEFT

COMPRESSOR

CONTACTOR

L3

T3

RIGHT

COMPRESSOR

CONTRACTOR

LINE

COPELAND COMPRESSOR WIRING

RUN CAPACITOR

USED WITH 046536-27

MOTOR ONLY

BLOWER

X1

A B

PUMP

1

11

2

12

EMPTY

EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH.

COMPRESSOR

TERMINALS

C NO C NO

EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04).

OUT

BRN OUT

PCB A. IN IN

OUT

CONT.

TRANS.

346

053566-40

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

BLK

BLK

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

BRNBRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK WHT

W2

BLK

BRN

ORG/WHT

ORN

ORG/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

41 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

BLK

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

LEFT

HPCO

L1

N

BLK WHT

WHT

WHT/BLK

WHT

WHT

YEL

WHT

WHT

BLKBLK

BLK

RED

BLK

BLK

GRN/YEL

GRN/YEL

GRN/YEL

GRN/YEL

GRN/YEL

WHT/BLK

WHT/BLK

WHT/BLK

YEL

GRN/YEL

WHT/BLK

M

BLK WHT

BLK

BLK WHT

M

WHT

BLK

RED/WHT

WHT

WHT

WHT

RED

WHT

BLK/WHT

BLK

BLK

RIGHT

HPCO

WHT/BLK

WHT

GRN/YEL

WHT

WHT

GRN/YEL

WHT

GRN/YELL

BLU/WHT

BRN BLK BLU

BRN BLK BLU

RED

LED

BARREL 2

BLK/WHT

RED

BLU

LED

BARREL 1

WHT

WHT

BLU

RED

M

BLK BLK

CARBONATOR FILL SWITCH

WHT

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDING UNIT BEFORE HANDLING SOLID

STATE COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1 AT

EACH END.

RIGHT

COMPRESSOR

CONTACTOR

RIGHT

COMPRESSOR

FIG.2

RIGHT

COMPRESSOR

CONTACTOR

GROUND FRAME

SECURELY

15 A

FUSE

BLK

GRN/YEL

WHT

S

R

LINE

RELAY

START CAPACITOR

C

INTERNAL OVERLOAD

RUN CAPACITOR

COPELAND COMPRESSOR WIRING

1

2

5

4

WHT

BRN

BLK

BRN

052396-1

EQUIPMENT

GROUND

BLEED RESISTOR

WHT(120 VOLTS; 220V-50Hz)

BLK(230 VOLTS)

BLK

BLU

START

13

MAIN

2

4

2C

THERMAL

O.L.

EXTRA

MAIN

65

RED 50 HZ

BLK 60 HZ

WHT COM

BRN

BRN

CAP

208/240 50/60 HZ

GE BLOWER MOTOR SCHEMATIC

FIG. 3

WHT

MAGNATEK-CENTURY

5

6 1

LEESON

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

T1 OR BLU

T8 OR RED

THERMAL OL

BRN

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN

START

5

1

GE/RBC BEATER MOTOR WIRING

CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5

1

2

3

FIG.1

FIG.2

1 2

1211

PRIMARY

SECONDARY

LEFT BEATER MOTOR

FIG.1

BLOWER

(FIG 3)

BARREL 1

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

SYR.SOL.

BARREL 1

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A.

CONTROL

SWITCH

SPST

EMI FILTER

LEFT

COMPRESSOR

FIG.2

LEFT

COMPRESSOR

CONTACTOR

T1 L2

T2

L1

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

531

W1

LEFT

COMPRESSOR

CONTACTOR

RIGHT BEATER MOTOR

FIG.1

T1 L2

T2

L1

COMP.

CONT.

COIL

BARREL 2

DEFROST

SOLENOID

BARREL 2

X1

A B

PUMP

1

11

2

12

EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH.

EMPTY

EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04).

CNO CNO

OUT

BROWN OUT

PCB A. IN IN

OUT

CONT.

TRANS.

346

053566-58

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

BLK

BLK

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

BLK

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

BRNBRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK BLK

W2

BLK

BRN

ORG/WHT

ORN

ORG/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

41 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

BLK

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

LEFT

HPCO

L1

N

BLK BLK

WHT/BLK

WHT

WHT

YEL

WHT

WHT

BLKBLK

BLK

RED

BLK

BLK

GRN/YELGRN/YEL

GRN/YEL

BLKBLK

WHT/BLK

5

6 1

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

WHT/BLK

WHT/BLK

YEL

GRN/YEL

WHT/BLK

M

BLKBLK

BLK BLK

M

WHT

RED/WHT

WHT

WHT

WHT

RED

WHT

BLK/WHT

BLK

BLK

RIGHT

HPCO

WHT/BLK

WHT

GRN/YEL

WHT

WHT

GRN/YEL

WHT

BLK

BLU/WHT

L2 L3

BLK

GRN/YEL

BLK

GRN/YEL

GRN/YEL

BLK

BLK

BLK

BLK

BLK

BLK

BLK

CNO

CNO

GRN

BRN

BLK

BLU

BRN

BLK

BLU

WHT

RED

LED

BARREL 2

BLK/WHT

RED

BLU

LED

BARREL 1

WHT

WHT

BLU

RED

M

BLK BLK

CARBONATOR FILL SWITCH

WHT

15A

FUSE

CONTROL

ENCLOSURE(S)

GRN/YEL

BLK

WHT

BLK

BLK

GRN/YEL

START

13

MAIN

2

4

2C

THERMAL

O.L.

EXTRA

MAIN

65

RED 50 HZ

BLK 60 HZ

WHT COM

BRN

BRN

CAP

208/240 50/60 HZ

GE MOTOR SCHEMATIC

FIG. 1

1 2

1211

PRIMARY

SECONDARY

LEFT BEATER MOTOR

BARREL 1

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

SYR.SOL.

BARREL 1

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

GROUND FRAME

SECURELY

J6

CONTROL PCB A.

CONTROL

SWITCH

SPST

EMI FILTER

LEFT

COMPRESSOR LEFT

COMPRESSOR

CONTACTOR

T1 L2T2L1

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1 2 34

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

531

W1

LEFT

COMPRESSOR

CONTACTOR

MAGNATEK-CENTURY LEESON

RIGHT BEATER MOTOR

RIGHT

COMPRESSOR RIGHT

COMPRESSOR

CONTRACTOR

T1 L2

T2

L1

RIGHT

COMPRESSOR

CONTRACTOR

COMP.

CONT.

COIL

BARREL 2

DEFROST

SOLENOID

BARREL 2

L3T3

LEFT

COMPRESSOR

CONTACTOR

L3

T3

RIGHT

COMPRESSOR

CONTRACTOR

LINE

COPELAND COMPRESSOR WIRING

BLOWER

(FIG 1)

X1

A B

PUMP

1

11

2

12

EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04)

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH.

COMPRESSOR

TERMINALS

EMPTY

EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04).

OUT

BRN OUT

PCB A. IN IN

OUT

CONT.

TRANS.

349

053636-27S

11/12/13

GROUND FRAME

SECURELY

YEL

BLK

BLK

YEL

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

WHT

ORG/WHT

BRN

WHT

WHT

M

BLK

CARB.

PUMP

WHT

CARB. FILL SWT

RED/BLK

YEL

BLK

LED

BARREL 1 LED

BARREL 2

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

LEFT

HPCO

BARREL 1

SYRUP OUT

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BLK

BLK

BRN

RED

BLK

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

BARREL 4

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

RIBBON CABLE

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

WHT

ORG/WHT

M

DEFROST

SOLENOID

RIGHT

HPCO

BARREL

3

HOPPER

FILL

SWITCH

CO2

PRESSURE

SWITCH

BLK

BLK

RED

BLK

BLK

BLK

BARREL

4

HOPPER

FILL

SWITCH

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

BARREL 2

KEYPAD

LCD DISPLAY

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

H2O

PRESSURE

SWITCH

WHT

PROXIMITY

SWITCH

BLK

WHT/BLK

BLU

RED

RED

BLK

BLK

PRP

PRP/WHT

WHT/BLK

BARREL 3

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 3

KEYPAD

BARREL 4

KEYPAD

RED

BLK

BLK

L2

BLU

1 4 1 4

BLK

WHT/BLKWHT/BLK

YEL

BLK

BARREL 1

BIB SWITCH

BLKBRN

BRN. BLK.

BARREL 2

SYRUP OUT

SWITCH

BARREL 3

SYRUP OUT

SWITCH

BRN

BARREL

4

BIB

SWITCH

BARREL 3

BIB SWITCH

BRN BLK

BRN BLK

BARREL 4

SYRUP OUT

SWITCH

BLU

BLK

BRN

BLU

BLK

BRN

YEL

L1 L2

L2L1

LINE

LOAD

M

BLK BLK

BLK

L1

BLK

BLK

W2

WHT/BLK

BRN

ORG/WHT

ORN

PRP/WHT BLK/WHT

WHT

BRN

WHT

BLK BLK

RED

BLU

RED

BLU

W2

RED/BLK

LED

BARREL 3

RED/BLK

BLK

BLK

LED

BARREL 4

BLK/YEL

BLK

WHT/BLK

WHT

WHT

BRN

BLK

BLK

BLK

BLK

BRN

M

BLK BLKBLKBLK

BRN

BLK BLU

BRN

BLK BLU

BARREL 4

BARREL 3

PROXIMITY

SWITCH

BLK

ORGORG

WHT

ORN

PRP/WHT

WHT

WHT

WHT

WHT

WHT

BRN

BLK

BLK

RIBBON CABLE

BLK BLK

BLK BLK

BLK BLK BLK BLKBLK

BLK

BLK

BLK

BLK BLK

WHT

RIBBON CABLE

RIBBON CABLE

RED RED RED

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES MUST BE

CONNECTED TO PIN 1 AT EACH END.

BRN

BRN

RUN CAPACITOR USED WITH

46536-27 MOTOR ONLY.

RED

BLU

BLU

RED

15A FUSE

15A FUSE

BARREL

2

WHT

RED/WHT

RED/WHT

BARREL

1DEFROST

SOLENOID

BARREL

3

RIGHT

BEATER

MOTOR

(SEE FIG 1)

WHT/BLK

BARREL

4

DEFROST

SOLENOID

WHT

RED/WHT

RED/WHT

S

R

LINE

RELAY

START CAPACITOR

C

INTERNAL OVERLOAD

RUN CAPACITOR

COPELAND COMPRESSOR WIRING

1

2

5

4

WHT

BRN

BLK

BRN

EQUIPMENT

GROUND

BLEED RESISTOR

WHT(120 VOLTS)

BLK(230 VOLTS)

BLK

BLU

(RIGHT INTERFACE PCB A. WI JUMPERS NON-FUNCTIONAL)

WHT

WHT

WHT WHT

CONTROL

ENCLOSURE(S)

1 2

1211

PRIMARY

SECONDARY

1 2

1211

BLK

YEL

WHT

BLK

BRN

WHT

ORG/WHT

WHT

LEFT

BEATER

MOTOR

(SEE FIG 1)

BARREL

1

LIQ. LINE

SOLENOID

LEFT

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

DEFROST

SOLENOID

4 3 2 1

BARREL

3

LIQ. LINE

SOLENOID

RIGHT

COMP.

CONT.

COIL

BARREL

3

H20 SOL.

BARREL

3

SYR.SOL

BARREL

3

CO2 SOL.

BARREL

4

CO2 SOL.

BARREL

4

H20 SOL.

BARREL

4

LIQ. LINE

SOLENOID

BARREL

4

SYR.SOL.

BLOWER

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

UNIVERSAL PCB A.

CONTROL

SWITCH EMI FILTER

LEFT

COMPRESSOR

LEFT COMPRESSOR

CONTACTOR

T1 L2T2

L1

LEFT INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

654321765432176543217654321

1 2 3 4 5 6 7 8

L2

J16 J13

X1

J8

A

B

W1

1 2 3 4

J7

4 3 2 1

RIGHT INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

X1

J8

A B

W1

1 2 3 4

4321

J6

J7

4321

531531

LEFT COMPRESSOR

CONTACTOR RIGHT

COMPRESSOR

RIGHT COMPRESSOR

CONTACTOR

T1 L2T2

L1

RIGHT COMPRESSOR

CONTACTOR

W1

CONT.

TRANS.

NOTE:

1

11

2

12

EMPTY-(RESERVED)

EMPTY-H2O PRESSURE SWITCH ACTIVE/JUMPER-H2O PRESSURE SWITCH BYPASSED

EMPTY-(JUMPER USED FOR DUAL BARREL DEFROST ONLY)

EMPTY-(RESERVED)

4 3

6 5

8 7

910

LEFT INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

SERVICE/TEST ONLY

EMPTY-(RESERVED)

IN

IN OUT

OUT

BRN OUT

PCB A.

MAGNATEK-CENTURY

5

6 1

LEESON

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

T1 OR BLU

T8 OR RED

THERMAL OL

BRN

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN

START

5

1

1/4 HP GE/RBC BEATER MOTOR WIRING

CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5

1

2

3

FIG.1

1/2 HP GE/RBC

3

2

1

YEL WHT

WHT/BLK

349

053636-33S

11/12/13

YEL

BLK

BLK

YEL

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

WHT

ORG/WHT

BRN

WHT

WHT

M

BLK

CARB.

PUMP

WHT

CARB. FILL SWT

RED/BLK

YEL

BLK

LED

BARREL 1 LED

BARREL 2

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

LEFT

HPCO

BARREL 1

SYRUP OUT

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BLK

BLK

BRN

RED

BLK

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

BARREL 4

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 3

WHT/BLK

RIBBON CABLE

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

WHT

ORG/WHT

M

BARREL

DEFROST

SOLENOID

RIGHT

HPCO

BARREL

3

HOPPER

FILL

SWITCH

CO2

PRESSURE

SWITCH

BLK

BLK

RED

BLK

BLK

BLK

BARREL

4

HOPPER

FILL

SWITCH

RIBBON CABLE SEE NOTE 3

WHT/BLK

BLK

BARREL 2

KEYPAD

LCD DISPLAY

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

H2O

PRESSURE

SWITCH

WHT

PROXIMITY

SWITCH

BLK

WHT/BLK

RED

BLK

BLK

PRP

PRP/WHT

WHT/BLK

BARREL 3

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 3

RIBBON CABLE SEE NOTE 3

BARREL 1

KEYPAD BARREL 3

KEYPAD

BARREL 4

KEYPAD

RED

BLK

BLK

L2

BLU

1 4 1 4

2. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

BLK

WHT/BLKWHT/BLK

YEL

BLK

BARREL 1

BIB SWITCH

BLK

BRN

BRN. BLK.

BARREL 2

SYRUP OUT

SWITCH

BARREL 3

SYRUP OUT

SWITCH

BRN

BARREL

4

BIB

SWITCH

BARREL 3

BIB SWITCH

BRN BLK

BRN BLK

BARREL 4

SYRUP OUT

SWITCH

BLU

BLK

BRN

BLU

BLK

BRN

YEL

L1 L2

L2L1

LINE

LOAD

M

BLK

BLK

BLK

L1

BLK

BLK

W2

WHT/BLK STRIPE

BROWN

ORG/WHT

ORN

PRP/WHT WHT/BLK

ORG/WHT

WHT

BRN

WHT

BLK BLK

BLK

RED

RED

BLU

W2

RED/BLK

LED

BARREL 3

RED/BLK

BLK

BLK

LED

BARREL 4

BLK/YEL

BLK

WHT/BLK

WHT

WHT

BRN

BLK

BLK

BLK

BLK

BRN

M

BLK BLKBLKBLK

BRN

BLK

BLU

BRN

BLK

BLU

BARREL 4

BARREL 3

PROXIMITY

SWITCH

BLK

ORGORG

WHT

ORN

PRP/WHT

WHT

WHT

WHT

WHT

WHT

BRN

RIBBON CABLE

BLK

BLK

BLK BLK

BLK

BLK

BLK BLKBLK

BLK

BLKBLKBLK

BLK BLK

WHT

RIBBON CABLERIBBON CABLE

RED RED RED

3. STRIPED WIRE ON RIBBON CABLES MUST BE

CONNECTED TO PIN 1 AT EACH END.

BLK BLK

BLK

L3

BLK

BLK

BLK

BLK

BLK

BLK

BLK BLK

BLK

BLK

BLK

1. COMPRESSOR PROTECTED UNDER

PRIMARY SINGLE PHASING CONDITIONS.

BRN

BRN

BLU

RED

RED

BLU

BLU

RED

RIBBON CABLE

SEE NOTE 3

BLU

GROUND FRAME

SECURELY

15A FUSE

15A FUSE

BARREL

1

BARREL

2

DEFROST

RED/WHT

WHT

BLK

SOLENOID

RED/WHT

WHT

3BARREL

4

DEFROST

SOLENOID

RUN CAPACITOR USED WITH

46536-27 MOTOR ONLY

RED/WHT

WHT

RED/WHT STR

WHT

WHT

WHT

CONTROL

ENCLOSURE(S)

1 2

1211

PRIMARY

SECONDARY

1 2

1211

BLK

YEL

WHT

BLK

BRN

WHT

ORG/WHT

WHT

BARREL

1

LIQ. LINE

SOLENOID

LEFT

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

DEFROST

SOLENOID

4321

BARREL

3

LIQ. LINE

SOLENOID

RIGHT

COMP.

CONT.

COIL

BARREL

3

H20 SOL.

BARREL

3

SYR.SOL

BARREL

3

CO2 SOL.

BARREL

4

CO2 SOL.

BARREL

4

H20 SOL.

BARREL

4

LIQ. LINE

SOLENOID

BARREL

4

SYR.SOL.

BLOWER

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

UNIVERSAL PCB A.

CONTROL

SWITCH

EMI FILTER

LEFT COMPRESSOR

LEFT COMPRESSOR

CONTACTOR

T1 L2

T2

L1

LEFT INTERFACE PCB A.

12345678 1 2

6543217

1234

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

654321765432176543217654321

12345678

L2

J16 J13

X1

J8

B

W1

1 2 3 4

J7

4321

RIGHT INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6543217

123 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

654321765432176543217654321

12345678

L2

J16 J13

X1

J8

A B

W1

1 2 3 4

1234

J6

J7

4321

5 3 15 3 1

LEFT COMPRESSOR

CONTACTOR

RIGHT

COMPRESSOR

RIGHT COMPRESSOR

CONTACTOR

T1 L2

T2

L1

RIGHT COMPRESSOR

CONTACTOR

LEFT COMPRESSOR

CONTACTOR

L3T3

RIGHT COMPRESSOR

CONTACTOR

L3

T3

LINE

COMPRESSOR WIRING

W1

A

CONT.

TRANS.

COMPRESSOR

TERMINALS

NOTE:

1

11

2

12

EMPTY-(RESERVED)

EMPTY-H2O PRESSURE SWITCH ACTIVE/JUMPER-H2O PRESSURE SWITCH BYPASSED

EMPTY-(JUMPER USED FOR DUAL BARREL DEFROST ONLY)

EMPTY-(RESERVED)

4 3

6 5

8 7

910

LEFT INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

RIGHT INTERFACE PCB A. W1 JUMPERS NON-FUNCTIONAL)

SERVICE/TEST ONLY

EMPTY-(RESERVED)

IN

IN OUT

OUT

BRN OUT

PCB A.

LEFT BEATER

MOTOR

(SEE FIG 1) RIGHT

BEATER

MOTOR

(SEE FIG 1)

MAGNATEK-CENTURY

5

6 1

LEESON

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

T1 OR BLU

T8 OR RED

THERMAL OL

BRN

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN

START

5

1

1/4 HP GE/RBC BEATER MOTOR WIRING

CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5

1

2

3

FIG.1

1/2 HP GE/RBC

3

2

1

YEL WHT

WHT/BLK

349

053636-58S

11/12/13

YEL

BLK

BLK

YEL

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

WHT

ORG/WHT

BRN

WHT

WHT

M

BLK

CARB.

PUMP

WHT

CARB.

FILL SWT

RED/BLK

YEL

BLK

LED

BARREL 1 LED

BARREL 2

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

LEFT

HPCO

BARREL 1

SYRUP OUT

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BLK

BLK

BRN

RED

BLK

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

BARREL 4

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 3

WHT/BLK

RIBBON CABLE

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

WHT

ORG/WHT

M

BARREL

DEFROST

SOLENOID

RIGHT

HPCO

BARREL

3

HOPPER

FILL

SWITCH

CO2

PRESSURE

SWITCH

BLK

BLK

RED

BLK

BLK

BLK

BARREL

4

HOPPER

FILL

SWITCH

RIBBON CABLE SEE NOTE 3

WHT/BLK

BLK

BARREL 2

KEYPAD

LCD DISPLAY

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

RIBBON

CABLE

H2O

PRESSURE

SWITCH

WHT

PROXIMITY

SWITCH

BLK

RED

BLK

BLK

PRP

PRP/WHT

WHT/BLK

BARREL 3

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 3

RIBBON CABLE SEE NOTE 3

BARREL 1

KEYPAD BARREL 3

KEYPAD

BARREL 4

KEYPAD

RED

BLK

N

BLU

1 4 1 4

2. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

BLK

WHT/BLK

WHT/BLK

YEL

BLK

BARREL 1

BIB SWITCH

BLKBRN

BRN. BLK.

BARREL 2

SYRUP OUT

SWITCH

BARREL 3

SYRUP OUT

SWITCH

BRN

BARREL

4

BIB

SWITCH

BARREL 3

BIB SWITCH

BRN BLK

BRN BLK

BARREL 4

SYRUP OUT

SWITCH

BLU

BLK

BRN

BLU

BLK

BRN

L1 L2

L2L1

LINE

LOAD

M

BLK

BLK

WHT

L1

BLK

BLK

W2

WHT/BLK

BRN

ORG/WHT

ORN

PRP/WHT BLK/WHT

ORN/WHT

WHT

BRN

WHT

WHT

WHT WHT

RED

BLU

RED

BLU

W2

RED/BLK

LED

BARREL 3

RED/BLK

BLK

BLK

LED

BARREL 4

BLK/YEL

BLK

WHT/BLK

WHT

WHT

BRN

BLK

BLK

BLK

BLK

BRN

M

BLK BLK

BLK

BLK

BRN

BLK

BLU

BRN

BLK

BLU

BARREL 4

BARREL 3

PROXIMITY

SWITCH

BLK

ORGORG

ORN

PRP/WHT

WHT

WHT

WHT

WHT

WHT

BRN

RIBBON CABLE

BLK

BLK

BLK

BLK

BLK

BLK BLK BLK

BLK

BLK

WHT

RIBBON CABLERIBBON CABLE

RED RED RED

3. STRIPED WIRE ON RIBBON CABLES MUST BE

CONNECTED TO PIN 1 AT EACH END.

BLK BLK

L2

BLK

BLK

BLK

WHT

WHT

BLK BLK

BLK

1. COMPRESSOR PROTECTED UNDER

PRIMARY SINGLE PHASING CONDITIONS.

L3

GRN/YEL

BLK

BLK

GRN/YEL

WHT/BLK

BLK

GRN/YEL

BLK

WHT/BLK

BLK

GRN/YEL

BLK

BLK

GRN/YEL

WHT

BLK

GRN/YEL

GRN/YEL

GRN/YEL

GRN/YEL

WHT

WHT

RED WHT

BLU

RED

RED

BLU

BLU

RED

RIBBON CABLE

SEE NOTE 3

BLU

15A FUSE

15A FUSE

GROUND FRAME

SECURELY

BARREL

2

DEFROST

RED/WHT

WHT

WHT

SOLENOID

BARREL

4

CO2 SOL.

WHT

SOLENOID

RED/WHT

WHT

RED/WHT

ORG/WHT

13

WHT

WHT

WHT

START

13

MAIN

2

4

2C

THERMAL

O.L.

EXTRA

MAIN

65

RED 50 HZ

BLK 60 HZ

WHT COM

BRN

BRN

CAP

208/240 50/60 HZ

GE MOTOR SCHEMATIC

FIG. 1

SEE FIG 1

CONTROL

ENCLOSURE(S)

1 2

1211

PRIMARY

SECONDARY

1 2

1211

BLK

YEL

WHT

WHT

BRN

WHT

ORG/WHT

WHT

BARREL

1

LIQ. LINE

SOLENOID

LEFT

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

BARREL

DEFROST

SOLENOID

4 3 2 1

BARREL

3

LIQ. LINE

SOLENOID

RIGHT

COMP.

CONT.

COIL

BARREL

3

H20 SOL.

BARREL

3

SYR.SOL

BARREL

3

CO2 SOL.

BARREL

4

DEFROST

BARREL

4

H20 SOL.

BARREL

4

LIQ. LINE

SOLENOID

BARREL

4

SYR.SOL.

BLOWER

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

UNIVERSAL PCB A.

CONTROL

SWITCH

EMI FILTER

LEFT COMPRESSOR

LEFT COMPRESSOR

CONTACTOR

T1 L2T2L1

LEFT INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6543217

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

X1

J8

B

W1

1 2 3 4

J7

4 3 2 1

RIGHT INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

12 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

X1

J8

A B

W1

1 2 3 4

4321

J6

J7

4321

531531

LEFT COMPRESSOR

CONTACTOR

RIGHT COMPRESSOR

RIGHT COMPRESSOR

CONTACTOR

T1 L2T2L1

RIGHT COMPRESSOR

CONTACTOR

LEFT COMPRESSOR

CONTACTOR

L3T3

RIGHT COMPRESSOR

CONTACTOR

L3T3

LINE

COMPRESSOR WIRING

W1

A

CONT.

TRANS.

COMPRESSOR

TERMINALS

NOTE:

1

11

2

12

EMPTY-(RESERVED)

EMPTY-H2O PRESSURE SWITCH ACTIVE/JUMPER-H2O PRESSURE SWITCH BYPASSED

EMPTY-(JUMPER USED FOR DUAL BARREL DEFROST ONLY)

EMPTY-(RESERVED)

4 3

6 5

8 7

910

LEFT INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

RIGHT INTERFACE PCB A. JUMPERS NON-FUNCTIONAL)

SERVICE/TEST ONLY

EMPTY-(RESERVED)

IN

IN OUT

OUT

BRN OUT

PCB A.

LEFT BEATER

MOTOR

(SEE FIG 1)

RIGHT

BEATER

MOTOR

(SEE FIG 1)

MAGNATEK-CENTURY

5

6 1

LEESON

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

T1 OR BLU

T8 OR RED

THERMAL OL

BRN

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN

START

5

1

1/4 HP GE/RBC BEATER MOTOR WIRING

CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5

1

2

3

FIG.1

1/2 HP GE/RBC

3

2 1

YEL WHT

WHT/BLK

355/355A/356

052840-27

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

BLK

LED

BARREL 2 LED

BARREL 1

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

BRNBRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK

W2

BLK

BRN

ORG/WHT

ORN

PRP/WHT

ORN/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

32

1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

M

FAN

WHT

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

HPCO

L1

BLK BLK

BLK

WHT/BLK

BLK

WHT

YEL

WHT

WHT

BLK

BLK

BLK

RED

BLK

BLK

WHT/BLK

BLK/WHT

BLK/WHT

M

WHT

BLK

CARBONATOR FILL SWITCH

WHT

BLK/WHT

WHT WHT

WHT/BLK

WHT

C NO C NO

BRN

BLK

BLU

BRN

BLK

BLU

BRN

BLU

RED

RED

BLU

15A FUSE

GROUND FRAME

SECURELY

BARREL

2

DEFROST

SOLENOID

RED/WHT

WHT

BLK

BLK

BARREL 1

SAMPLER SWITCH

(PUSHBUTTON-OPTIONAL)

BLK

BLK

BARREL 2

SAMPLER SWITCH

(PUSHBUTTON-OPTIONAL)

P.O.P.

DISPLAY

WHT

L2

RED

3 2

RED/BLK

FAN MOTOR

RUN CAPACITOR

(USED WITH AIR

COOLED UNITS ONLY)

BLK

GRN

BLK/WHT

61

CARBONATOR

PUMP

CCW ROTATION

FROM LEAD END

M

BLK

CARBONATOR

FILL SWITCH

WHT

BLK/WHT

L1

2

1

BLK

3

WHT

BLK

BLK

BLK

WHT

GRN/YEL

BLK

WHT

GRN/YEL

N

LOW H2O PRESSURE

INDICATOR LIGHT

H2O

PRESSURE

SWITCH

REMOTE CARBONATOR WIRING 115V

(SEE FIG.1 IF REMOTE CARBONATOR)

OPTIONAL

GRN/YEL

CONTROL SWITCH

SPST

FIG. 1

OPTIONAL

OPTIONAL

T1 T2

L1 L2

COMPRESSOR

CONTACTOR

COMPRESSOR

CONTACTOR

MAGNATEK-CENTURY

3

6 1

LEESON

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

T1 OR BLU

J12 OR PUR

THERMAL PROTECTOR

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN 1

START

5

1

GE/RBC BEATER MOTOR WIRING

NOTE:

1. FOR LOW VOLTAGE REMOVE BROWN (P2) FROM TERMINAL #3

AND PLACE ON TERMINAL #5, REMOVE WHITE (T2) FROM TERMINAL #5

AND PLACE ON TERMINAL #2.

2. TO REVERS ROTATION INTERCHANGE RED (T8) AND

BLACK (J9-KC, KCR OR T5-KH) LEADS.

3. WHEN MORE THAN ONE CAPACITOR IS USED CONNECT

IN PARALLEL.

1

2

3

B

3

MAIN 2

T3 OR ORN

T2 OR WHT

RUN CAP.

(WHEN SPEC.)

J11 OR BRN

START CAP.

(KC MOT0R

ONLY), LEAD

T5 OR BLACK

CONNECTED

DIRECTLY TO SWT

FOR KH MOTORS

J9 OR BLK

T8 OR RED

INT.

BRN

HIGH VOLTAGE CW ROTATION SHOWN

1 2

1211

PRIMARY

SECONDARY

LINE

EQUIPMENT

GROUND

COPELAND COMPRESSOR WIRING

S

R

C

1

2

5

4

WHT

BRN

BLK

BRN

BEATER MOTOR

BARREL

1

LIQ. LINE

SOLENOID

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

BARREL

1

DEFROST

SOLENOID

4321

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A.

EMI FILTER

COMPRESSOR

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1234

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

12345678

L2

J16 J13

J8

W1

1 2 3 4

J7

4321

531

W1

PUMP

X1

A B

RELAY

START CAPACITOR

INTERNAL OVERLOAD

RUN CAPACITOR

BLEED RESISTOR

CONTROL

TRANSFORMER

1

11

2

12

EMPTY

EMPTY

EMPTY

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH.

OUT

BRN OUT

PCB A.

IN IN

OUT

355/355A/356

052840-33

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

BLK

LED

BARREL 2 LED

BARREL 1

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

BRNBRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK

W2

BLK

BRN

ORG/WHT

ORN

PRP/WHT

ORN/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

32 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

M

FAN

WHT

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

HPCO

L1

BLK

BLK

WHT/BLK

BLK

WHT

YEL

WHT

WHT

BLK

BLK

BLK

RED

BLK

BLK

WHT/BLK

BLK/WHT

BLK/WHT

M

WHT

BLK

CARBONATOR FILL SWITCH

WHT

BLK/WHT

WHT WHT

WHT/BLK

WHT

C NO C NO

BRN

BLK

BLU

BRN

BLK

BLU

BRN

BLU

RED

RED

BLU

15A FUSE

GROUND FRAME

SECURELY

BARREL

2

DEFROST

SOLENOID

RED/WHT

WHT

BLK

BLK

BARREL 1

SAMPLER SWITCH

(PUSHBUTTON-OPTIONAL)

BLK

BLK

BARREL 2

SAMPLER SWITCH

(PUSHBUTTON-OPTIONAL)

P.O.P.

DISPLAY

WHT

L2

RED

3 2

RED/BLK

FAN MOTOR

RUN CAPACITOR

USED WITH AIR

COOLED UNITS ONLY

BLK

GRN

BLK/WHT

61

(SEE FIG.1 IF REMOTE CARBONATOR)

OPTIONAL

CONTROL SWITCH

SPST

L3

BLK

BLK

OPTIONAL

OPTIONAL

L3

T3

COMPRESSOR

CONTACT

BLK

T1 T2

L1 L2

COMPRESSOR

CONTACTOR

COMPRESSOR

CONTACTOR

CARBONATOR

PUMP

CCW ROTATION

FROM LEAD END

M

BLK

CARBONATOR

FILL SWITCH

WHT

BLK/WHT

L1

2

1

BLK

3

WHT

BLK

BLK

BLK

WHT

GRN/YEL

BLK

WHT

GRN/YEL

N

LOW H2O PRESSURE

INDICATOR LIGHT

H2O

PRESSURE

SWITCH

REMOTE CARBONATOR WIRING

GRN/YEL

FIG. 1

MAGNATEK-CENTURY

3

6 1

LEESON

2

4 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

YEL WHT

WHT/BLK

T1 OR BLU

J12 OR PUR

THERMAL PROTECTOR

YEL

WHT/BLK

4

2

WHT

T4 OR YEL

T5 OR BLK

A

P2 OR BRN

P1 OR PUR

MAIN 1

START

5

1

GE/RBC BEATER MOTOR WIRING

NOTE:

1. FOR LOW VOLTAGE REMOVE BROWN (P2) FROM TERMINAL #3

AND PLACE ON TERMINAL #5, REMOVE WHITE (T2) FROM TERMINAL #5

AND PLACE ON TERMINAL #2.

2. TO REVERS ROTATION INTERCHANGE RED (T8) AND

BLACK (J9-KC, KCR OR T5-KH) LEADS.

3. WHEN MORE THAN ONE CAPACITOR IS USED CONNECT

IN PARALLEL.

1

2

3

B

3

MAIN 2

T3 OR ORN

T2 OR WHT

RUN CAP.

(WHEN SPEC.)

J11 OR BRN

START CAP.

(KC MOT0R

ONLY), LEAD

T5 OR BLACK

CONNECTED

DIRECTLY TO SWT

FOR KH MOTORS

J9 OR BLK

T8 OR RED

INT.

BRN

HIGH VOLTAGE CW ROTATION SHOWN

1 2

1211

PRIMARY

SECONDARY

BEATER MOTOR

BARREL

1

LIQ. LINE

SOLENOID

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

BARREL

1

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A.

EMI FILTER

COMPRESSOR

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

531

W1

PUMP

X1

A B

CONTROL

TRANSFORMER

1

11

2

12

EMPTY

EMPTY

EMPTY

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH.

OUT

BRN OUT

PCB A.

IN IN

OUT

355/355A/356

052840-40

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

BLK

LED

BARREL 2 LED

BARREL 1

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

BRNBRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK

W2

BLK

BRN

ORG/WHT

ORN

PRP/WHT

ORN/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

32

1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

M

FAN

WHT

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

HPCO

L1

WHT

WHT

WHT/BLK

WHT

WHT

YEL

WHT

WHT

BLK

BLK

BLK

RED

BLK

BLK

WHT/BLK

3

6 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

BLK/WHT

BLK/WHT

M

WHT

BLK

CARBONATOR FILL SWITCH

WHT

BLK/WHT

WHT WHT

WHT/BLK

WHT

C NO C NO

BRN

BLK

BLU

BRN

BLK

BLU

BRN

BLU

RED

RED

BLU

15A FUSE

GROUND FRAME

SECURELY

BARREL

2

DEFROST

SOLENOID

RED/WHT

WHT

BLK

BLK

BARREL 1

SAMPLER SWITCH

(PUSHBUTTON-OPTIONAL)

BLK

BLK

BARREL 2

SAMPLER SWITCH

(PUSHBUTTON-OPTIONAL)

P.O.P.

DISPLAY

WHT

RED

3 2

RED/BLK

FAN MOTOR

RUN CAPACITOR

USED WITH AIR

COOLED UNITS ONLY

BLK

BLK/WHT

61

(SEE FIG.1 IF REMOTE CARBONATOR)

OPTIONAL

CONTROL SWITCH

SPST

N

GRN

OPTIONAL

OPTIONAL

GRN/YEL

GRN/YEL

GRN/YEL

GRN/YEL

GRN/YEL

GRN/YEL

GRN/YEL CONTROL

ENCLOSURE(S)

LEESON

2

4 1

YEL WHT

WHT/BLK

T1 T2

L1 L2

COMPRESSOR

CONTACTOR

COMPRESSOR

CONTACTOR

CARBONATOR

PUMP

CCW ROTATION

FROM LEAD END

M

BLK

CARBONATOR

FILL SWITCH

WHT

BLK/WHT

L1

2

1

BLK

3

WHT

BLK

BLK

BLK

WHT

GRN/YEL

BLK

WHT

GRN/YEL

N

LOW H2O PRESSURE

INDICATOR LIGHT

H2O

PRESSURE

SWITCH

REMOTE CARBONATOR WIRING

GRN/YEL

FIG. 1

1 2

1211

PRIMARY

SECONDARY

LINE

EQUIPMENT

GROUND

COPELAND COMPRESSOR WIRING

S

R

C

1

2

5

4

WHT

BRN

BLK

BRN

BEATER MOTOR

BARREL

1

LIQ. LINE

SOLENOID

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

BARREL

1

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A.

EMI FILTER

COMPRESSOR

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6 5 4 3 2 17

1234

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

1 2 3 4 5 6 7 8

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

531

W1

MAGNATEK-CENTURY

PUMP

X1

A B

RELAY

START CAPACITOR

INTERNAL OVERLOAD

RUN CAPACITOR

BLEED RESISTOR

CONTROL

TRANSFORMER

1

11

2

12

EMPTY

EMPTY

EMPTY

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH.

OUT

BRN OUT

PCB A.

IN IN

OUT

355/355a/356

052840-58

11/12/13

YEL

BLK

YEL

BLK

RED/WHT

WHT

PRP/WHT

WHT

BLU/WHT

WHT

ORN

ORG/WHT

BRN

RED/BLK

BLK

LED

BARREL 2 LED

BARREL 1

RED/BLK

BLK

BLK

RED/BLK

BARREL 2

BARREL 1

BLK

BLK

BRN

RED

BLK

BLK

BLK

RED

BARREL

2

BIB

SWITCH

BARREL

2

HOPPER

FILL

SWITCH

THERMISTORS

PROBES

RIBBON CABLE SEE NOTE 2

WHT/BLK

BLK

LCD DISPLAY

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

RIBBON CABLE

SEE NOTE 2

WHT

PROXIMITY

SWITCHES

BARREL 2

BARREL 1

RIBBON CABLE SEE NOTE 2

RIBBON CABLE SEE NOTE 2

BARREL 1

KEYPAD BARREL 2

KEYPAD

NOTE:

1. STATIC ELECTRICITY MAY CAUSE

DAMAGE TO SOLID STATE COMPONENTS.

ELIMINATE STATIC ELECTRICITY BY TOUCHING

GROUNDED UNIT BEFORE HANDLING SOLID STATE

COMPONENTS.

2. STRIPED WIRE ON RIBBON CABLES

MUST BE CONNECTED TO PIN 1

AT EACH END.

BRNBRN

BRN BRN

BARREL 2

SYRUP OUT

SWITCH

L1 L2

L2L1

LINE

LOAD

M

BLK

W2

BLK

BRN

ORG/WHT

ORN

PRP/WH

ORN/WHT

BRN

WHT

ORN

ORNBLK

BLK

WHT/BLK

32 1 4

H2O

PRESSURE

SWITCH

PRP/WHT

PRP/WHT

BRN

RED

BLK/YEL

BRN

YEL

BLK

YEL

BLK

M

FAN

WHT

BLK

BLK

BLK

WHT

BRN

PRP

PRP

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

WHT

BLK

BLK

RED

BLK

C02

PRESSURE

SWITCH

BARREL

1

HOPPER

FILL

SWITCH

BARREL

1

BIB

SWITCH

BARREL 1

SYRUP OUT

SWITCH

HPCO

L1

BLK

BLK

WHT/BLK

BLK

WHT

YEL

WHT

WHT

BLK

BLK

BLK

RED

BLK

BLK

WHT/BLK

3

6 1

BEATER MOTOR WIRING

YEL WHT

WHT/BLK

BLK/WHT

BLK/WHT

M

WHT

BLK

CARBONATOR FILL SWITCH

WHT

BLK/WHT

WHT WHT

WHT/BLK

WHT

C NO C NO

BRN

BLK

BLU

BRN

BLK

BLU

BRN

BLU

RED

RED

BLU

15A FUSE

GROUND FRAME

SECURELY

BARREL

2

DEFROST

SOLENOID

RED/WHT

WHT

BLK

BLK

BARREL 1

SAMPLER SWITCH

(PUSHBUTTON-OPTIONAL)

BLK

BLK

BARREL 2

SAMPLER SWITCH

(PUSHBUTTON-OPTIONAL)

P.O.P.

DISPLAY

WHT

L2

RED

3 2

RED/BLK

FAN MOTOR

RUN CAPACITOR

USED WITH AIR

COOLED UNITS ONLY

BLK

BLK/WHT

61

(SEE FIG.1 IF REMOTE CARBONATOR)

OPTIONAL

CONTROL SWITCH

SPST

N L3

GRN

GRN/YEL

GRN/YEL

GRN/YEL

OPTIONAL OPTIONAL

COMPRESSOR

CONTACTOR

L3

T3

BLK BLK

GRN/YEL

BLK

GRN/YEL

GRN/YEL

WHT WHT

LEESON

2

4 1

YEL WHT

WHT/BLK

COMPRESSOR

T2

L1 L2

COMPRESSOR

CONTACTOR

COMPRESSOR

CONTACTOR

T1

CARBONATOR

PUMP

CCW ROTATION

FROM LEAD END

M

BLK

CARBONATOR

FILL SWITCH

WHT

BLK/WHT

L1

2

1

BLK

3

WHT

BLK

BLK

BLK

WHT

GRN/YEL

BLK

WHT

GRN/YEL

N

LOW H2O PRESSURE

INDICATOR LIGHT

H2O

PRESSURE

SWITCH

REMOTE CARBONATOR WIRING

GRN/YEL

FIG. 1

GRN/YEL CONTROL

ENCLOSURE(S)

1 2

1211

PRIMARY

SECONDARY

BEATER MOTOR

BARREL

1

LIQ. LINE

SOLENOID

COMP.

CONT.

COIL

BARREL

1

H20 SOL.

BARREL

1

SYR.SOL.

BARREL

1

CO2 SOL.

BARREL

2

CO2 SOL.

BARREL

2

H20 SOL.

BARREL

2

LIQ. LINE

SOLENOID

BARREL

2

SYR.SOL.

BARREL

1

DEFROST

SOLENOID

4 3 2 1

1 2

J1

J10 J11

J7

J9

J5 J6

J4

J3

J2

J6

CONTROL PCB A. EMI FILTER

INTERFACE PCB A.

1 2 3 4 5 6 7 8 1 2

6543217

1 2 3 4

J14

J12J15J11

J5 J3 J1J4 J2

J10J9

L1

6 5 4 3 2 176 5 4 3 2 176 5 4 3 2 176 5 4 3 2 1

12345678

L2

J16 J13

J8

W1

1 2 3 4

J7

4 3 2 1

531

W1

MAGNATEK-CENTURY

PUMP

X1

A B

CONTROL

TRANSFORMER

1

11

2

12

EMPTY

EMPTY

EMPTY

EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED

EMPTY

SERVICE/TEST ONLY

4 3

6 5

8 7

910

INTERFACE PCB A. W1 JUMPER BLOCK DETAIL

JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED

AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH.

OUT

BRN OUT

PCB A.

IN IN

OUT