Taylor Freezer 345 346 349 355 Users Manual
345346349355 to the manual e29671f1-cc81-466d-929d-4491509fe4ad
2015-02-02
: Taylor Taylor-Taylor-Freezer-345-346-349-355-Users-Manual-449397 taylor-taylor-freezer-345-346-349-355-users-manual-449397 taylor pdf
Open the PDF directly: View PDF 
.
Page Count: 87
| Download | |
| Open PDF In Browser | View PDF |
OPERATOR’S MANUAL Model 345/346/349/355 Slush Freezers Original Operating Instructions 039710- M 6/19/01 (Original Publication) Updated 11/22/13 Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Fax: E- mail: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: A E 2001 Carrier Commercial Refrigeration, Inc. 039710- M Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties. All rights reserved. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072 Table of Contents Section 1 To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Cooled Refrigeration Units (Water Cooled Units Only) . . . . . . . . . . . . . . . . Water Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Syrup System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 2 To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 4 Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 345 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 346 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 349 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 355 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 5 Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Liquid Crystal Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operational Mode Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operator Menu Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Syrup Out Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CO2 Out Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Out Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio Alarm Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sampling Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Daily Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 6 Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Priming/Brixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Day Closing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining Product From the Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table of Contents 1 1 2 2 2 4 7 8 10 10 11 12 13 14 15 16 16 16 17 17 17 22 23 23 23 23 23 23 24 24 29 33 35 35 35 36 36 Models 345, 346, 349, 355 Table of Contents - Page 2 Section 7 Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 8 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 9 Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 10 Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 11 Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 12 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 38 38 38 39 40 42 43 45 48 70 Note: Continuing research results in steady improvements; therefore, information in this manual is subject to change without notice. Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be the original set of instructions. E 2001 Carrier Commercial Refrigeration, Inc. (Updated November, 2013) 039710- M Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties. All rights reserved. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072 Models 345, 346, 349, 355 Table of Contents Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. This unit has many sharp edges that can cause severe injuries. Site Preparation Installer Safety Review the area where the unit will be installed before uncrating the unit. Make sure that all possible hazards to the user and the equipment have been addressed. In all areas of the world, equipment should be installed in accordance with existing local codes. Please contact your local authorities if you have any questions. Air Cooled Units Care should be taken to ensure that all basic safety practices are followed during the installation and servicing activities related to the installation and service of Taylor equipment. S S S S Air cooled units require 6” (152 mm) minimum air space around all sides. Failure to allow adequate clearance can reduce the refrigeration capacity of the freezer and possibly cause permanent damage to the compressor(s). Only authorized Taylor service personnel should perform installation and repairs on the equipment. Authorized service personnel should consult OSHA Standard 29CFRI910.147 or the applicable code of the local area for the industry standards on lockout/tagout procedures before beginning any installation or repairs. Authorized service personnel must ensure that the proper PPE is available and worn when required during installation and service. Authorized service personnel must remove all metal jewelry, rings, and watches before working on electrical equipment. For Indoor Use Only: This unit is designed to operate indoors, under normal ambient temperatures of 70_-75_F (21_-24_C). The freezer has successfully performed in high ambient temperatures of 104_(40_C) at reduced capacities. This unit must NOT be installed in an area where a water jet or hose can be used. NEVER use a water jet or hose to rinse or clean the unit. Failure to follow this instruction may result in electrocution. This unit must be installed on a level surface to avoid the hazard of tipping. Extreme care should be taken in moving this equipment for any reason. Two or more persons are required to safely move this unit. Failure to comply may result in personal injury or equipment damage. The main power supply(s) to the freezer must be disconnected prior to performing any repairs. Failure to follow this instruction may result in personal injury or death from electrical shock or hazardous moving parts as well as poor performance or damage to the equipment. Uncrate the unit and inspect it for damage. Report any damage to your Taylor Distributor. This piece of equipment is made in the USA and has USA sizes of hardware. All metric conversions are approximate and vary in size. Note: All repairs must be performed by an authorized Taylor Service Technician. 131122 Models 345, 346, 349, 355 1 To the Installer Water Cooled Refrigeration Units IMPORTANT: The water filter (064422- SER) must be thoroughly flushed with water before connecting it to the machine. This removes carbon particles that could clog the flow control. To flush the filter, connect the inlet end of the filter to the water supply. Position the outlet end of the filter over an empty pail. Open the water supply. Allow water to flow through the filter until the water exiting the filter is clear. Close the water supply. Attach the outlet end of the filter to the machine. Reopen the water supply. (Water Cooled Units Only) Failure to use adequate size water lines may cause the unit to go off on high head pressure and shut down. Depending on local water conditions, it may be advisable to install a water strainer to prevent foreign substances from clogging the automatic water valve. There are two water “in” connections and one water “out” line connection. DO NOT install a hand shut-off valve on the water “out” line! Water should always flow in this order: first, through the automatic water valve; second, through the condenser; and third, through the outlet fitting to an open trap drain. IMPORTANT: Water pressures are pre-set at the factory. Do not adjust the water. Improper water adjustments may cause operation discrepancies. A back flow prevention device is required on the incoming water connection side. Please refer to the applicable National, State, and local codes for determining the proper configuration. Figure 1 Electrical Connections Water Connections In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70- 1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered necessary for safety. Compliance therewith and proper maintenance will result in an installation essentially free from hazard! In all other areas of the world, equipment should be installed in accordance with the existing local codes. Please contact your local authorities. An adequate cold water supply must be provided with a hand shut-off valve. On the back of the unit, a 3/8” (9.5 mm) M.F.L. water connection has been provided for easy hook-up. A flexible line is recommended, if local codes permit. A minimum of 25 psi water pressure is required to avoid having the unit cut out the low water pressure switch. A booster pump must be provided if this pressure is not available. Note: Water lines beyond 200 ft. (61 m) require 1/2” (13 mm) water lines. FOLLOW YOUR LOCAL ELECTRICAL CODES! INSTALL POTABLE WATER CONNECTION WITH ADEQUATE BACK-FLOW PROTECTION TO COMPLY WITH APPLICABLE NATIONAL, STATE AND LOCAL CODES. Each unit requires one power supply for each data label on the unit. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity, and other electrical specifications. Refer to the wiring diagram provided inside of the control box for proper power connections. It is always a good practice to have a filter system to improve the quality of the water and to avoid clogging the operating components. 120828 To the Installer 2 Models 345, 346, 349, 355 Beater Rotation CAUTION: THIS EQUIPMENT MUST BE PROPERLY GROUNDED! FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK! Beater rotation must be clockwise as viewed looking into the freezing cylinder. Note: The following procedures should be performed by a trained service technician. DO NOT operate this freezer with larger fuses than specified on the unit data label. Failure to follow this instruction may result in electrocution or damage to the machine. To correct the rotation on a three- phase unit, interchange any two incoming power supply lines at freezer main terminal block only. To correct rotation on a single- phase unit, change the leads inside the beater motor. (Follow the diagram printed on the motor.) This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC 60417-1) on both the removable panel and the equipment’s frame. Initial Freezing Cylinder Cleaning Due to the types of products used in FCB equipment, it is imperative that the freezing cylinder and the inlet tube be thoroughly brush cleaned, rinsed, and sanitized before running any product. Stationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation. Prepare a cleaning solution, using 2 oz. of liquid detergent in 2 gallons of warm water. Using this solution, brush clean the freezing cylinder and the inlet tube. Rinse the freezing cylinder and the inlet tube with clean water and then sanitize, using the sanitizing procedures outlined in this Operator Manual, starting on page 29. Appliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected or not used for long periods, or during initial installation, shall have protective devices such as a GFI, to protect against the leakage of current, installed by the authorized personnel to the local codes. Refrigerant In consideration of our environment, Taylor uses only earth friendly HFC refrigerants. The HFC refrigerant used in this unit is R404A. This refrigerant is generally considered non-toxic and non-flammable, with an Ozone Depleting Potential (ODP) of zero (0). Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion. However, any gas under pressure is potentially hazardous and must be handled with caution. NEVER fill any refrigerant cylinder completely with liquid. Filling the cylinder to approximately 80% will allow for normal expansion. 120828 Models 345, 346, 349, 355 3 To the Installer Use only R404A refrigerant that conforms to the AHRI standard 700 specification. The use of any other refrigerant may expose users and operators to unexpected safety hazards. 4. Refrigerant liquid sprayed onto the skin may cause serious damage to tissue. Keep eyes and skin protected. If refrigerant burns should occur, flush immediately with cold water. If burns are severe, apply ice packs and contact a physician immediately. c. Be sure all control switches on the front panel are in the “OFF” position. d. The freezer must be properly grounded. A harness with three nylobrade tubes feeds through the base pan and exits the rear of the freezer. (The Model 355 is equipped with four tubes.) a. Connect the CO2 line to the CO2 regulator that is closest to the CO2 tank (primary regulator). This line will supply CO2 to the freezer. Taylor reminds technicians to be cautious of government laws regarding refrigerant recovery, recycling, and reclaiming systems. If you have any questions regarding these laws, please contact the factory Service Department. WARNING: R404A refrigerant used in conjunction with polyolester oils is extremely moisture absorbent. When opening a refrigeration system, the maximum time the system is open must not exceed 15 minutes. Cap all open tubing to prevent humid air or water from being absorbed by the oil. Figure 2 b. Syrup System Connections 1. Water pipe connections and fixtures directly connected to a potable water supply shall be sized, installed and maintained according to federal, state and local laws. 2. Hook up cold water supply to freezer to supply water to the carbonator. A minimum of 21 PSI of water pressure is required at the low pressure switch. The low pressure switch will cause the entire freezer to shut down if the water pressure drops below 7 PSI for longer than one minute. Note: For Bag-in-Box units (BIB), connect the #1 line to the Bag-In-Box instead of the syrup tank. The water regulator should be set at 35 PSI. When the power switch is turned on the water pump will immediately activate to maintain water pressure. 3. Figure 3 Electrical Hook-Up a. One power cord. b. Refer to the data label. Connect the #1 line to the syrup tank for the left side of the freezer as viewed from the front of the machine. This line will supply syrup to the left syrup sentry. c. Connect the #2 line to the syrup tank (or the Bag-in-Box) for the right side of the freezer. This line will supply syrup to the right syrup sentry. 131122 To the Installer 4 Models 345, 346, 349, 355 d. 5. 6. Connect the #4 line on the Model 355 to the water regulator on the remote carbonator. This line monitors the water pressure supplied to the unit. Set the primary regulator on the CO2 tank to 90 PSI (6.2 BAR). There are two spare CO2 lines provided. Use one of the spare CO2 lines to connect one end to the individual regulator (secondary regulator) and the other end to the first syrup tank. Use the other spare CO2 line to connect the CO2 to the second syrup tank. Figure 6 7. Set the secondary regulator on the CO2 tank to 60 PSI (4.1 BAR) for the syrup tanks or the BIB pumps. Figure 4 Note: For Bag-in-Box units, connect the CO2 lines to the Bag-in-Box pumps instead of the syrup tanks. Figure 7 Figure 5 Models 345, 346, 349, 355 5 8. Turn the cold water supply on. 9. Check for CO2 leaks. This can be done by closing the valve on the top of the CO2 tank. Watch the high pressure gauge; it should hold pressure. If it does not, there is a CO2 leak. Use a soap solution to locate and repair the leak. To the Installer 10. 11. For Bag-in-Box syrup delivery system, connect the two spare CO2 lines from the secondary regulator to each “Gas In” fitting on the pumps. Set secondary regulator pressure to 60 PSI (4.1 BAR) depending on the length of syrup line run to the unit. Important: Ensure that the Bag-in-Box switch is enabled. The CO2 regulator assembly (primary regulator) inside the freezer should be set at 60 PSI (4.1 BAR). The secondary regulator, located inside the freezer just behind the primary regulator, can be adjusted from 20 to 25 PSI. (The factory recommendation is 20 PSI.) Increasing the pressure from 20 PSI will increase the overrun. You should always stay within the 20 to 25 PSI range as the gauge reflects the pressure in the hopper and barrel. The setting will be determined by the desired overrun and the syrup used. To the Installer 6 12. The CO2 low pressure switch requires at least 74 PSI before the freezer will start. It is set to cut out at 60 PSI and in at 74 PSI. 13. The pressure relief valve on the hopper cover is set to relieve at 30 PSI in case of excess pressure in the hopper. 14. There are check valves in the CO2, syrup, and water lines to prevent any back flow of soda water, product, or CO2. 15. The CO2 solenoids which supply CO2 to the hoppers are wired to provide CO2 in all control settings except “DEFROST” and “OFF”. Models 345, 346, 349, 355 Section 2 To the Operator The freezer(s) you have purchased has been carefully engineered and manufactured to give you dependable operation. compliant with the EU Directive as well as other similar legislation in effect after August 13, 2005. Therefore, it must be collected separately after its use is completed, and cannot be disposed as unsorted municipal waste. The user is responsible for returning the product to the appropriate collection facility, as specified by your local code. This unit(s), when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, this machine will require cleaning and scheduled maintenance. A minimum amount of care and attention is necessary if the operating procedures outlined in this manual are followed closely. For additional information regarding applicable local laws, please contact the municipal facility and/or local distributor. This Operator’s Manual should be read before operating or performing any maintenance on your equipment. Compressor Warranty Disclaimer The refrigeration compressor(s) on this unit are warranted for the term stated in the Limited Warranty section in this manual. However, due to the Montreal Protocol and the U.S. Clean Air Act Amendments of 1990, many new refrigerants are being tested and developed, thus seeking their way into the service industry. Some of these new refrigerants are being advertised as drop- in replacements for numerous applications. It should be noted that in the event of ordinary service to this unit’s refrigeration system, only the refrigerant specified on the affixed data label should be used. The unauthorized use of alternate refrigerants will void your Taylor compressor warranty. It is the unit owner’s responsibility to make this fact known to any technician he employs. Your freezer will NOT eventually compensate and correct for any errors during the set-up or filling operations. Thus, the initial assembly and priming procedures are of extreme importance. It is strongly recommended that all personnel responsible for the equipment’s operation study these procedures together in order to be properly trained and to make sure that no misunderstandings exist. In the event you should require technical assistance, please contact your local authorized Taylor Distributor for service. Note: Your Taylor warranty is valid only if the parts are authorized Taylor parts, purchased from the local authorized Taylor Distributor, and only if all required service work is provided by an authorized Taylor service technician. Taylor reserves the right to deny warranty claims on units or parts if non- Taylor approved parts or incorrect refrigerant were installed in the unit, system modifications were performed beyond factory recommendations, or it is determined that the failure was caused by abuse, misuse, neglect, or failure to follow all operating instructions. For full details of your Taylor Warranty, please see the Limited Warranty section in this manual. It should also be noted that Taylor does not warrant the refrigerant used in its equipment. For example, if the refrigerant is lost during the course of ordinary service to this machine, Taylor has no obligation to either supply or provide its replacement either at billable or unbillable terms. Taylor does have the obligation to recommend a suitable replacement if the original refrigerant is banned, obsoleted, or no longer available during the five year warranty of the compressor. Taylor will continue to monitor the industry and test new alternates as they are being developed. Should a new alternate prove, through our testing, that it would be accepted as a drop-in replacement, then the above disclaimer would become null and void. To find out the current status of an alternate refrigerant as it relates to your compressor warranty, call the local Taylor Distributor or the Taylor Factory. Be prepared to provide the Model/Serial Number of the unit in question. Note: Constant research results in steady improvements; therefore, information in this manual is subject to change without notice. If the crossed out wheeled bin symbol is affixed to this product, it signifies that this product is 131122 Models 345, 346, 349, 355 7 To the Operator Section 3 Safety We at Taylor are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built- in safety features to protect both you and the service technician. As an example, warning labels have been attached to the freezer to further point out safety precautions to the operator. IMPORTANT - Failure to adhere to the following safety precautions may result in severe personal injury or death. Failure to comply with these warnings may damage the machine and its components. Component damage will result in part replacement expense and service repair expense. S DO NOT operate the freezer unless it is properly grounded. S DO NOT operate the freezer with larger fuses than specified on the freezer data label. S All repairs must be performed by an authorized Taylor service technician. S The main power supplies to the machine must be disconnected prior to performing any repairs. For Cord Connected Units: Only Taylor authorized service technicians or licensed electricians may install a plug or replacement cord on these units. S DO NOT operate the freezer without reading this Operator Manual. Failure to follow this instruction may result in equipment damage, poor freezer performance, health hazards, or personal injury. This appliance is to be used only by trained personnel. It is not intended for use by children or people with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. S Stationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation. S Appliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected, not used for long periods, or during initial installation, shall have protective devices such as a GFI to protect against the leakage of current, installed by authorized personnel to the local codes. Supply cords used with this unit shall be oil-resistant, sheathed flexible cable, not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion. S This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC 60417-1) on both the removable panel and the equipment’s frame. If the supply cord is damaged, it must be replaced by an authorized Taylor service technician in order to avoid a hazard. DO NOT use a water jet to clean or rinse the freezer. Failure to follow these instructions may result in serious electrical shock. Failure to follow these instructions may result in electrocution. Contact your local authorized Taylor Distributor for service. 131122 Safety 8 Models 345, 346, 349, 355 S DO NOT allow untrained personnel to operate this machine. S DO NOT operate the freezer unless all service panels and access doors are restrained with screws. Cleaning and sanitizing schedules are governed by your state or local regulatory agencies and must be followed accordingly. Please refer to the cleaning section of this manual for the proper procedure to clean this unit. DO NOT remove any internal operating parts (example: freezer door, beater, scraper blades, etc.) unless all control switches are in the OFF position and ALL PRESSURE IN THE FREEZING CYLINDER HAS BEEN RELIEVED. Failure to follow these instructions may result in contaminated product or severe personal injury to fingers or hands from hazardous moving parts. This machine is designed to maintain product temperature under 41_F (5_C). Any product being added to this machine must be below 41_F (5_C). Failure to follow this instruction may result in health hazards and poor freezer performance. S CAUTION: This unit is pressurized when in operation. The control switch must be in the OFF position until the unit is completely assembled. No part should ever be removed from the machine while it is in operation. No part should be removed until the control switch has been turned to the OFF position and all pressure has been relieved by opening the draw valve. This unit has many sharp edges that can cause severe injuries. S S Failure to follow these instructions may result in severe personal injury from hazardous moving parts or from the impact of propelled parts. DO NOT put objects or fingers in the door spout. This may contaminate the product and cause severe personal injury from blade contact. IMPORTANT: DO NOT obstruct air intake and discharge openings: These units require 6” (152 mm) minimum air space around all sides. Failure to follow this instruction may cause poor freezer performance and damage to the machine. USE EXTREME CAUTION when removing the beater asssembly. The scraper blades are very sharp. For Indoor Use Only: This unit is designed to operate indoors, under normal ambient temperatures of 70_-75_F (21_-24_C). The freezer has successfully performed in high ambient temperatures of 104_(40_C) at reduced capacities. This freezer must be placed on a level surface. Failure to comply may result in personal injury or equipment damage. DO NOT run the unit without product. Failure to follow this instruction can result in damage to the unit. Access to the service area of the unit must be restricted to persons having knowledge and practical experience with the unit, in particular as far as safety and hygiene are concerned. NOISE LEVEL: Airborne noise emission does not exceed 78 dB(A) when measured at a distance of 1.0 meter from the surface of the machine and at a height of 1.6 meters from the floor. 131122 Models 345, 346, 349, 355 9 Safety Section 4 Operator Parts Identification Model 345 2 1 3 16 15 14 17 4 13 12 18 11 5 6 10 8 7 9 Item Description Part No. Item Description Part No. 1 Panel A.-Side Left X45136 11 Panel-Service 044916 2 Hood 044618 12 Panel-Front-Lower 043599-BLA 3 Panel-Rear 044921-SP1 13 Stud-Nose Cone 5/16-18 020445 4 Panel A.-Side Right X44919 *13a Washer-Freezer Stud 036265 5 Caster-Swivel 3/4-10 St. 3” 021279 14 Card-Flavor Packet 035324 6 Caster-Locking Swivel - 3” 030307 15 Card-FCB POP 043957 7 Lock-Caster Bracket 032571 16 Panel-Front-Upper 043600-BLA 8 Shield-Splash 043719 17 Plate A.-Dec-345-346-355 Black 043639-BLA 9 Tray-Drip *345/6* Black w/Drain 043720-SP 18 Decal- Dec- Taylor Domed 053761 Pan-Drip 19-1/2 Long 035034 Pan-Drip (White) For Drip Guide 043612 10 *19 *Not Shown Operator Parts Identification 10 Models 345, 346, 349, 355 Model 346 3 2 1 15 14 16 13 17 12 18 4 5 8 10 19 9 11 Item Description Part No. 1 Panel A.-Side Left X44917 2 Hood 3 Panel-Rear 4 Item 20 6 7 Description Part No. 12 Panel-Front-Lower 043599-BLA 044618 13 Stud-Nose Cone 5/16-18 020445 044921-SP1 *13a Washer-Freezer Stud 036265 Panel A.-Side *346*AC*R*Filter X53611 14 Card-Flavor Packet 035324 5 Caster-Swivel 3/4-10 St. 3” 021279 15 Card-FCB POP 043957 6 Caster-Locking Swivel 3” 030307 16 Panel-Front-Upper 043600-BLA 7 Lock-Caster Bracket 032571 17 Plate-Dec-345-346-355* Black 043639-BLA 8 Shield-Splash 043719 18 Decal- Dec- Taylor Domed 053761 9 Tray-Drip 20” L x 8” D x 3-3/4 043720-SP 19 Filter- Air 18L x 16.5H x .70W AC 052779- 1 10 Pan-Drip 19-1/2 Long 035034 20 Cover- Hole- Filter- Snap In 053801 11 Panel-Service *346* Filter 053612 *21 Pan-Drip (White) For Drip Guide 043612 *Not Shown Models 345, 346, 349, 355 11 Operator Parts Identification Model 349 2 1 3 14 13 15 12 11 4 17 16 5 6 10 7 18 9 Item Description Part No. Item 8 Description Part No. 1 Panel A.-Side Left X42289 12 Stud-Nose Cone 5/16-18 020445 2 Hood 042166 *12a Washer-Freezer Stud 036265 3 Panel-Rear *349* Drain Hole 042198 13 Card-Flavor Packet 035324 4 Panel A.-Side Right X42291 14 Panel-Front Upper 042081-BLA 5 Caster-Swivel 3/4-10 St. 3” 021279 15 Plate-Dec *349* Black 035410-BLA 6 Caster-Locking Swivel 3” 030307 16 Decal- Dec- Taylor Domed 053761 7 Lock-Caster Bracket 032571 17 Cover- Hole- Filter- Snap In 053801 8 Panel-Service *349* AC 053652 18 Filter- Air 18 L x 16.5 H x .7 W 052779- 1 9 Tray-Drip (Black) w/Drain 038275-SP *19 Pan A.-Drip w/Hose Left X42201 10 Shield-Splash 038276 *20 Pan A.-Drip w/Hose Right X42203 11 Panel-Front-Lower 042082-BLA *Not Shown Operator Parts Identification 12 Models 345, 346, 349, 355 Model 355 3 2 4 1 14 5 13 12 12a 15 11 6 10 7 9 8 Item Description Part No. Item Description Part No. 1 Panel-Front -Upper 043600-BLA 10 Pan-Drip 035034 2 Panel-Side-Left 044619-SP 11 Panel-Front-Lower 043599-BLA 3 Hood 044618 12 Stud-Nose Cone 5/16-18 020445 4 Panel-Rear-Stainless 044621-SS *12a Washer-Freezer Stud 036265 5 Panel-Side-Right 044620-SP 13 Card-Flavor Packet 035324 6 Leg-4” 3/8-16 Stud 036397 14 Card-FCB POP 043957 7 Shelf-Drip Tray 049697 15 Plate-Dec-345-346-355 Black 043639-BLA 8 Tray-Drip 20” L x 8” D x 3-3/4 043720 *16 Pan-Drip (White) For Drip Guide 043612 9 Shield-Splash 043719 *Not Shown Models 345, 346, 349, 355 13 Operator Parts Identification Door Assembly ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 DOOR 1m O-RING-1.129 ODX.989ID 039219 1a CAP-SPOUT-DOOR-FCB-BLK 046191-BLA 1n NUT-SPOUT-DOOR-PRESS. 039323 1b SPRING-COMP.480X.072X3.0 039320 2 NUT-STUD 043666 1c VALVE-DRAW-DOOR-PRESS. 039324 3 O-RING-9/16 OD X .103W 016369 O-RING-5-1/4ODX.210W (DOOR) 017003 1d 1e SPOUT-DOOR-FCB-BLACK 046190-BLA 4 BEARING-FRONT-PRESSURE 039349 5 BEATER-PLASTIC-FCB-PRESS. 041182 6 BLADE-SCRAPER-FCB-16INCH 041103 7 SHAFT-BEATER-SLUSH-PRES 039337 8 SEAL-DRIVE SHAFT 032560 9* O-RING-7/8 OD X .139W (BEATER SHAFT) 025307 10 BUSHING-BEATER SHAFT/BOOT SEAL 042278 1f HANDLE-DRAW-FCB-BLACK 046192-BLA 1g PIN-PIVOT-SPOUT-DOOR 039321 1h SLIDE-HANDLE-DOOR-BLK 046193-BLA 1i SCREW-10-32X3/8PHL-TRUS HD SS 053869 1j O-RING-9/32 OD X 1/16 WALL 029751 1k PLUG-PRIME-SLUSH-PRESS. 039568 1l DOOR-FREEZER-SLUSH-PRES 039573 *NOTE: O-RING 025307 IS NOT USED ON CURRENT MODELS. HOWEVER, UNITS BUILT PRIOR TO 10/09 THAT HAVE NOT BEEN UPDATED WITH METAL REAR SHELL BEARING X67222 STILL REQUIRE O-RING. 120828 Operator Parts Identification 14 Models 345, 346, 349, 355 Accessories 2 1 3 4 5 KAY-5 6 8 R 7 ® Sanitizer/Cleaner KEEP OUT OF REACH OF CHILDREN CAUTION FOR INSTITUTIONAL USE ONLY 1 OZ (28.4 g) 048260 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 PAIL-MIX 10 QT 013163 6 KIT A.-TUNE UP X39699 2 BRUSH-MIX PUMP BODY-3”X7” 023316 7 LUBRICANT-TAYLOR HI PERF 048232 3 BRUSH-DOUBLE ENDED 013072 8 SANITIZER KAY-5 25 PACKETS 041082 4 BRUSH-REAR BRG 1”DX2“L 013071 * SANITIZER STERA-SHEEN 010425 5 BRUSH-DRAW VALVE 1-1/2”OD 014753 Models 345, 346, 349, 355 *NOT SHOWN 15 Operator Parts Identification Section 5 Important: To the Operator Figure 8 Item 1 2 3 4 5 6 The following chart identifies the symbol definitions used on the Model 349. Description Control Switch Liquid Crystal Display Keypad- Left Keypad- Right Product Light- Left Side Product Light- Right Side = ON = OFF = AUTO = PRIME = BEATER MOTOR = ALARM SILENCE = MENU/SELECT Symbol Definitions Control Switch To better communicate in the International arena, the words on many of our operator switches and keys have symbols to indicate their functions. The Model 349 is designed with these International symbols. Important: To the Operator The control switch is located on the top of the control channel. When placed in the ON position, allows Slushtecht operation. 16 Models 345, 346, 349, 355 Liquid Crystal Display Pressing both AUTO keys will display this screen. AUTO OK The Liquid Crystal Display (LCD) is located on the front control panel. The LCD is used to show the current operating mode of the freezing cylinders. The LCD also indicates whether there is enough syrup, CO2, and water being supplied to the freezer. If an error in the machine operation occurs, a warning tone will sound and the word “FAULT” will flash on the third line of the display. MODE SYRUP CO2=OK AUTO OK WATER=OK Line 1 indicates the operating mode for each cylinder. Line 2 indicates the status of the syrup systems in each freezing cylinder. Line 3 indicates if there is a fault in the system (left side). The same rules apply to the fourth line which indicates the status of the CO2 and the H2O. Operational Mode Display AUTO OK - - FAULT- CO2=OK When the unit is plugged into the wall receptacle and the power switch is placed in the ON position, this screen appears. MODE SYRUP OPERATOR MENU ABCDEFGH EXIT MENU <- - - -> SEL Operator Menu Timeout OFF OK If the display is left in the operator menu or any of the operator menu selections, except for Current Conditions, the display will return to the system mode screen 60 seconds after the last keypress. The Current Conditions screen will be displayed until manually changed. WATER=OK Note: Syrup, CO2 and water are satisfied. Models 345, 346, 349, 355 WATER=OK The OPERATOR MENU is used to enter into the operating screens. To access the OPERATOR MENU, simply press the word “MENU”. The cursor will flash under the letter “A”, indicating that this is screen A. To select a different screen, use the arrow keys to move the cursor to the desired screen selection and press the SEL key. This display will remain on the LCD for 60 seconds unless a key is pressed. If any key is pressed (or 60 seconds passes), then the next screen appears. CO2=OK OFF OK Operator Menu Display SAFETY TIMEOUT ANY KEY ABORTS OFF OK MODE SYRUP 17 Important: To the Operator Finding Current Fault Conditions 2. Screen B is FAULT DESCRIPTION. The fault description will indicate if there is a fault in one of the freezing cylinders. When the actual fault is corrected, the warning tone will stop. Only items 9 and 10 require pressing the OFF/<--- key to clear the fault message and the warning tone. FAULT DESCRIPTION L: BEATER OVERLOAD R: BEATER OVERLOAD CLR +++ Fault Messages Beater Overload Beater is out on overload. Chk Refrig Sys Psi Compressor is out on high head pressure (or low suction pressure = option that applies to some units) Thermistor Short Shorted thermistor probe. Thermistor Open Open thermistor probe. H2O Pressure Low Water pressure is low. CO2 Pressure Low CO2 pressure is low. 3. Syrup Pressure Low Syrup is no longer present. BRL Temp 2 High Freezing cylinder is not cooling after 5 minutes. No Fault Found No fault conditions are apparent. 4. SEL CHK REFRIG SYS PSI - Compressor is out on high head pressure (or low suction pressure = option that applies to some units). When this fault occurs, the machine automatically turns off. The fault clears when the condition is corrected. FAULT DESCRIPTION L: CHK REFRIG SYS PSI R: CHK REFRIG SYS PSI CLR +++ Freezing cylinder temperature is above 120_F (49_C). BRL Not Cooling BEATER OVERLOAD - Beater motor is out on overload. When this fault occurs, the machine automatically turns off. The fault clears when the condition is corrected. SEL THERMISTOR SHORT - One or both of the barrel (freezing cylinder) thermistor probes are faulty. The following are explanations of the possible faults and the display screens. FAULT DESCRIPTION L: THERMISTOR SHORT R: NO FAULT FOUND CLR +++ Lines 2 and 3 indicate the faults found in the left and right freezing cylinders respectively. The screen below indicates that no faults exist on either side. To see if there is more than one fault, press the +++ key. Note: On a Model 349, faults for freezing cylinders 1 and 2 are shown on the first screen. Press the SEL key to read fault messages for freezing cylinders 3 and 4. 1. 5. NO FAULT FOUND - No fault conditions are apparent. FAULT DESCRIPTION L: NO FAULT FOUND R: NO FAULT FOUND CLR +++ THERMISTOR OPEN - One or both of the barrel (freezing cylinder) thermistor probes are faulty. FAULT DESCRIPTION L: THERMISTOR OPEN R: NO FAULT FOUND CLR +++ SEL SEL SEL 060801 Important: To the Operator 18 Models 345, 346, 349, 355 6. SYRUP PRESS LOW - When the syrup out indicator displays a lack of syrup, a 15 minute internal timer will start. At this time, no refrigeration or product flow from the flow control will be allowed. Only the beater and CO2 operate. If the syrup is not replenished at the end of the 15 minutes, the freezing cylinder will shut down and this fault message will appear. Replenish the syrup, and the fault message and warning tone will clear. If using a tank system, priming may be required. (Example shown is for the right side.) FAULT DESCRIPTION L: NO FAULT FOUND R: SYRUP PRESS LOW CLR +++ 7. 10. SEL Models 345, 346, 349, 355 SEL BRL TEMP 2 HIGH - A maximum allowable product temperature has been established to prevent product from excessive heating. If the product exceeds 120_F (49_C) temperature for any reason (in any mode of operation), the entire unit shuts down. FAULT DESCRIPTION L: BARREL TEMP 2 HIGH R: NO FAULT FOUND CLR +++ H2O PRESSURE LOW - When the water out indicator displays a lack of water, a 60 second internal timer will start. If the water is not replenished at the end of the 60 seconds, all freezing cylinders will shut down and this fault message will appear. Replenish the water and the fault message and warning tone will clear. FAULT DESCRIPTION L: H2O PRESSURE LOW R: H2O PRESSURE LOW CLR +++ BRL NOT COOLING - A freezing cylinder check has been established for the AUTO mode of operation. If a freezing cylinder enters the AUTO mode, the control will check product temperature. After five minutes, it will again check product temperature. If product temperature does not drop in that five minute time span, the freezing cylinder will shut down and this message will appear on the fault screen. For this check to be valid, the product temperature must be above 40_F (4.4_C), and the fill switch cannot be activated. If a fill condition exists during this time, the five minute check will be re-initiated. FAULT DESCRIPTION L: BARREL NOT COOLING R: NO FAULT FOUND CLR +++ SEL CO2 PRESSURE LOW - When the CO2 out indicator displays a lack of CO2, a 60 second internal timer will start. If the CO2 is not replenished at the end of the 60 seconds, both freezing cylinders will shut down and this fault message will appear. Replenish the CO2 and the fault message and warning tone will clear. FAULT DESCRIPTION L: CO2 PRESSURE LOW R: CO2 PRESSURE LOW CLR +++ 8. 9. SEL Faults, when corrected, are cleared from the fault description screen, with the following exceptions: BRL NOT COOLING and BRL TEMP 2 HIGH. These faults require the operator to press the OFF key (when in the FAULT DESCRIPTION screen) in order for the fault to discontinue. To see if there is more than one fault in either freezing cylinder, press the plus key. To return to the OPERATOR MENU, press the SEL key once. To return to the Main Screen, use the right arrow key to cycle to MENU ITEM A, then press the SEL key. SEL 19 Important: To the Operator Screen C is SET CLOCK. Move the cursor under the number you wish to change. Press the +++ key to increase the number; press the - - - key to decrease the number. When the desired time and date appears, press the SEL key once to return to the OPERATOR MENU. Repeat the procedure for the right side of the unit. MANUAL DEFROST RIGHT SIDE Note: The clock is programmed with military time. SET CLOCK 14:30 <- - - -> YES <- - - - - - > NO SEL 6/25/01 +++ - - - Note: The models 345 and 355 allow only one freezing cylinder to be defrosted at a time. This applies to freezing cylinder pairs on the model 349. Attempting to place a freezing cylinder into defrost while the other freezing cylinder is defrosting will result in the following screen. (Model 346 does not have this restriction.) SEL This screen will appear if an invalid date is entered. (example: If the date entered exceeds the days of that month.) SET CLOCK 14:30 02/31/01 INVALID DATE SEL ALREADY IN DEFROST This screen allows the Daylight Saving Time options. DAYLIGHT SAVING TIME DISABLE ENABLE <- - - - - - > Press the SEL key to return the unit to the OPERATOR MENU. SEL If the Daylight Saving Time option is enabled, then the time will be advanced by one hour at 2:00 a.m. on the first Sunday in April, and will be retarded by one hour at 2:00 a.m. on the last Sunday in October. Screen E is SYSTEM INFORMATION. It consists of 6 display features. Press the SEL key to advance to the next feature. Screen D is MANUAL DEFROST. This screen allows the operator to manually defrost the left side of the unit. The first feature indicates the software version. Place the cursor under YES, press the SEL key, and the command will be executed. MANUAL DEFROST LEFT SIDE <- - - - - - > YES SYSTEM INFORMATION 355 CONTROL UVC2 VERSION 2.03 NO SEL SEL 041011 Important: To the Operator 20 Models 345, 346, 349, 355 The second feature indicates the bill of material number and the serial number. POWER SAVER STANDBY SUN CYCLE 1 SUN +++ - - - It also indicates if the unit is equipped with a water pressure switch. Each freezing cylinder has eight possible defrost times (cycles) for each day of the week. If all seven days have the same time for a given cycle, then the following screen will appear. This example shows that ALL seven days have CYCLE 1 programmed for 9:00. Press the +++ or - - - keys to view other cycles. SEL The third feature indicates the version number of the language and text. SYSTEM INFORMATION LANGUAGE VERSION 1.05 ENGLISH 386 DEFROST TIME LEFT ALL CYCLE 1 SEL +++ The fourth feature will display the Power Saver Mode, as OFF, REST, or STANDBY. - - - 09:00 SEL If one or more days of the week have a given cycle programmed at different times, then the following display will appear. This example shows that Sunday’s CYCLE 1 is programmed for 9:00. The fact that SUN is displayed (instead of ALL) indicates that some other day(s) CYCLE 1 is programmed for a different time (or not programmed at all). Using the cursor keys, place the cursor under the cycle number. Press the +++ or - - - keys to view other defrost times (cycles) for the day shown. Place the cursor under the day (SUN) and press the +++ or - - - keys to access the other days of the week. If the Power Saver Mode is OFF, the following screen will be displayed. POWER SAVER MODE OFF SEL If a Power Saver Mode is programmed, one of the following screens will appear. (The model 349 will display defrost information for freezing cylinders 1, 2, 3, and 4 instead of LEFT and RIGHT.) DEFROST TIME LEFT CYCLE 1 SUN <- - - - - - > There are seven possible Power Saver Mode time frames (cycles). The second display line shows the cycle (1 of 7) as well as the time and day at which the Power Saver Mode will begin for that cycle. The third line shows the time and day that the Power Saver Mode will end for that cycle. Press the +++ or - - - keys to view other cycles. Models 345, 346, 349, 355 SEL The fifth feature will indicate the left side defrost time(s) and which day(s) the defrost will occur. B.O.M. 035527C000 S/N K0000000 WITH H20 PRESS SW POWER SAVER REST SUN CYCLE 1 SUN +++ - - - 01:00 08:30 +++ - - - 09:00 SEL The sixth feature will indicate the right side defrost time(s) and which day(s) the defrost will occur. Note: The functionality is the same as described previously for the left side defrost. DEFROST TIME RIGHT ALL CYCLE 1 01:00 08:30 SEL +++ 21 - - - 10:00 SEL Important: To the Operator DEFROST TIME RIGHT SUN CYCLE 1 <- - - - - - > +++ - - - The fault description is listed on the third line of the fault page. 10:00 SEL FAULT HISTORY 06/25/01 B H2O PRESS LOW +++ - - - Press the SEL key to return to the OPERATOR MENU. Screen F is CURRENT CONDITIONS. This screen displays the current viscosity and product temperature for each freezing cylinder. An asterisk will indicate which side is refrigerating. Press the SEL key to return to the OPERATOR MENU. Screen H is SERVICE MENU. This screen allows the authorized service technician to access service information. Return to the OPERATOR MENU by using the arrow keys to move the cursor under the letter “A”, and press the MENU/SEL key. The following screen is exemplary of models 345, 346, and 355. The model 349 displays all four freezing cylinders. OPERATOR MENU ABCDEFGH SERVICE MENU <- - - - - - > Syrup Out Indicator AUTO OUT 1 08:34 +++ - - - CO2- OK SEL MODE SYRUP AUTO OK WATER- OK If the word “OUT” appears in one of the columns next to the word “SYRUP”, it indicates a lack of syrup or syrup pressure being supplied for the indicated freezing cylinder. If the unit is in the AUTO or PRIME modes, the product light will flash and a warning tone will sound for that freezing cylinder. At this time, replace the appropriate syrup. As a safety feature, the refrigeration system automatically stops to prevent a freeze-up in the freezing cylinder. Press the arrow keys to increase or decrease the fault page. Page numbers are located in the upper right hand corner of the display. The most recently recorded fault will appear on page 1. FAULT HISTORY 06/25/01 R SYRUP PRESS LOW +++ - - - SEL 27.5F 26.5F SEL Screen G is FAULT HISTORY. This option provides a record of the last 20 faults. The display also indicates the date and time each fault occurs. FAULT HISTORY 06/25/01 NO FAULT FOUND SEL Press the MENU/SEL key to return to the OPERATOR MENU. Note: Viscosity is checked only when product temperature is below 40_F/4.4_C. CURRENT CONDITIONS L* 999HD R 1200HD 3 08:32 If a syrup out condition occurs on one side, that side will enter the HOLD mode at which time refrigeration remains off, the beater continues to run, and the CO2 solenoid is closed for that side to prevent the dispensing of product. The opposite side will not be affected. 2 08:33 SEL 060522 Important: To the Operator 22 Models 345, 346, 349, 355 CO2 Out Indicator AUTO OK MODE SYRUP CO2- OUT Audio Alarm Silencer The audio alarm will be disabled if the ALARM SILENCE key is pressed. If a new fault or fault condition occurs or the system mode changes, the audio alarm will be re-enabled automatically. If the audio alarm is silenced for greater than 30 minutes without correcting the fault, it will be re-enabled automatically. AUTO OK WATER- OK On the LCD, if the word “OUT” appears next to the word “CO2” it indicates a lack of CO2 being supplied to the freezer. The product light will also flash and a warning tone will sound. This will continue until the CO2 is replaced. If the CO2 is not replaced within one minute, the machine will shut down and a fault message will appear. Product Light When the light is flashing, it indicates that the product is not at serving viscosity. This will occur during the initial freeze down, a defrost cycle and a FAULT condition and during power saver modes. Water Out Indicator AUTO OK MODE SYRUP CO2- OK Sampling Valve AUTO OK The sampling valve is located behind the front drip tray. The sampling valve is used to obtain a brix reading. WATER- OUT On the LCD, if the word “OUT” appears next to the word “WATER”, it indicates a lack of water being supplied to the freezer. In addition, the product light will flash and a warning tone will sound. This will continue until the proper amount of water is supplied to the freezer. If the water is not supplied within one minute, the machine will shut down and a fault message will appear. Models 345, 346, 349, 355 Daily Procedures The following procedure should be performed daily. Remove the splash shield, front drip tray and center drip pan. Take these parts to the sink and brush-clean them. Re-install the parts onto the freezer. 23 Important: To the Operator Section 6 Operating Procedures Assembly The Models 345, 346 and 355 contain two 7 quart (6.6 liter) freezing cylinders. The Model 349 contains four 7 quart (6.6 liter) freezing cylinders. MAKE SURE THE CONTROL SWITCH IS IN THE OFF POSITION. Failure to do so may result in personal injury or component damage. CAUTION: This unit is pressurized when in operation. The control switch, located on the top side of the control box must be in the OFF position until the unit is completely assembled. No part should ever be removed from the machine while it is in operation. No parts should be removed until the control switch has been turned to the OFF position and all pressure has been relieved at the draw handle. Note: When lubricating parts, use an approved food grade lubricant (example: Taylor Lube HP). Step 1 Lubricate the o-ring groove. Slide the o-ring into the groove on the drive shaft. Lubricate the drive shaft seal groove, the o-ring, and the shaft portion that comes in contact with the bearing on the beater drive shaft. DO NOT lubricate the hex end of the drive shaft. The syrup flow controls combine the two ingredients of soda water and syrup, and send this combination to the mix hoppers. As product is drawn, new product from the hopper will flow through a mix feed tube down into the freezing cylinder. The mix hopper is supplied with 20 pounds of CO2 gas for dispensing the finished product. We begin our instructions at the point where the parts are disassembled and laid out to air dry. The following procedures will show you how to assemble the parts into the freezer, sanitize them, and prime the freezer with fresh product. Duplicate the following procedures, where they apply, for the remaining freezing cylinder(s). Figure 9 Lubricate the inside diameter of the drive shaft seal. Install the drive shaft seal bushing in the drive shaft seal. If you are disassembling the machine for the first time or need information to get to this starting point in our instructions, turn to page 36 , “Disassembly” and start there. Figure 10 Operating Procedures 24 Models 345, 346, 349, 355 Note: The drive shaft bushing must be positioned in the center of the drive shaft seal. Step 2 Install the beater assembly. First check the scraper blades for any nicks or signs of wear. If any nicks are present or if the blade is worn, replace both blades. If the blades are in good condition, place the scraper blades over the holding pins on the beater. Slide the seal and bushing over the shaft and groove until it snaps into place. Fill the inside portion of the seal with 1/4” more lubricant and evenly lubricate the end of the seal that fits onto the rear shell bearing. Note: Each hole on the scraper blade must fit securely over each pin. Figure 13 Figure 11 Align the flats on the end of the beater assembly with the drive shaft. Make sure the beater assembly locating pin is in position in the locating hole of the drive shaft. Turn the beater slightly to be certain that the beater is properly seated. When in position, the beater will be approximately 3/8” inside the front of the freezing cylinder. Insert the beater drive shaft into the freezing cylinder, hex end first, and into the rear shell bearing until the seal fits securely over the rear shell bearing. Be certain the drive shaft fits into the drive coupling without binding. Remove any excess lubricant from the seal. Important: Failure to properly seat the beater may cause damage to the beater and the door. Figure 12 Models 345, 346, 349, 355 Figure 14 25 Operating Procedures Note: The scraper blades on the beater assembly should be in the 6 and 12 o’clock positions. This will enable freezer door installation. Figure 17 Snap the draw valve handle onto the door spout. Align the hole in the draw valve with the slot in the draw handle. Figure 15 Step 3 Install the draw valve. Slide the two o-rings into the grooves on the draw valve. Lubricate the o-rings and the valve as illustrated below. Figure 18 Slide the pivot pin through the draw handle and into the draw valve. Figure 16 Insert the draw valve into the freezer door spout from the front of the unit. The valve is properly installed when the hole in the draw valve is visible in the slot of the freezer door spout. Operating Procedures Figure 19 26 Models 345, 346, 349, 355 Place the draw handle slide over the opening in the draw handle and the pivot pin. Secure the assembly with screws. Step 4 Install the prime plug. Place the two o-rings on the prime plug and lightly lubricate. Figure 20 Insert the spring into the front of the door spout. Figure 23 Step 5 Place the large o-ring into the door groove and lightly lubricate. Figure 21 Place the threaded cap on the end of the draw valve cavity. Turn the cap clockwise until it is secure. Figure 24 Note: Every three months, discard the o-rings and install new o-rings. Figure 22 Models 345, 346, 349, 355 27 Operating Procedures Step 6 Install the front bearing. Do not lubricate the front bearing. Figure 27 Install the hopper cover. Lock it into place. Figure 25 Step 7 Install the freezer door. Position the door on the four studs on the front of the freezing cylinder. Firmly push the door into place. Install the four handscrews on the studs and finger-tighten them equally in a criss-cross pattern to insure that the door is snug. Do not over-tighten the handscrews. Figure 28 Attach the vinyl tube to the pressure relief on the hopper cover. Position the open end of the vinyl tube into the rear drip pan. Figure 26 Figure 29 Repeat Steps 1 through 8 for the remaining freezing cylinder(s). Step 8 Place the o-ring into the groove of the hopper cover. Operating Procedures 28 Models 345, 346, 349, 355 Step 9 Install the center drip pan through the front of the machine. Step 2 Prepare two gallons (7.6 liters) of an approved 100 PPM sanitizing solution (example: Kay-5R). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. IMPORTANT: Make sure the sanitizer is completely dissolved. If your freezer uses Bag in Box syrup, follow steps 3 through 5. If your freezer uses syrup tanks, follow the instructions on page 5. Step 3 Bag in Box Units Only: Using an empty bag of syrup, cut the syrup line connection from the end of the bag. Figure 30 Sanitizing Note: If a unit is sanitized, and will not be used for an extended period of time, clean water should be used to flush all sanitizer from the lines prior to storage of the unit. Upon return to service, the unit must be sanitized prior to use. Figure 32 Step 1 Open the lighted display door. Remove the hood and the side panels to gain access to the hoppers. Place the control switch in the ON position. Step 4 Connect the syrup line to the syrup connection that was cut from the syrup bag. Figure 31 Figure 33 Models 345, 346, 349, 355 29 Operating Procedures Step 5 With the bag connector attached to the syrup line, place the syrup line into the pail of sanitizing solution. Figure 36 Step 7 Place a mix pail beneath the sampling valve which is located behind the front drip tray. Slowly open the sampling valve and allow sanitizer to flow through this line and into the pail. After approximately 1/2 gallon of sanitizer has been dispensed, close the valve. Step 8 Raise the prime plug only enough to allow a slight hissing sound. Place an empty pail under the door spout. When sanitizing solution begins to exit the relief port opening in the freezer door, lower the prime plug. Press the OFF key. Figure 34 Replace Steps 3 - 5 for Syrup Tank Units: Pour the solution into a clean, empty syrup tank. Place the syrup tank cover in position. Remove the CO2 line and syrup line number one from the syrup tank for freezing cylinder number one. Connect these lines to the spare syrup tank filled with sanitizing solution. Figure 37 Figure 35 Step 9 Prepare two gallons (7.6 liters) of an approved 100 PPM sanitizing solution (example: Kay-5R). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Step 6 Press the PRIME key. This will cause the sanitizing solution to flow through the lines and into the mix hopper. Operating Procedures 30 Models 345, 346, 349, 355 Step 10 With the pail beneath the door spout, open the draw valve and relieve all pressure from the freezing cylinder. Remove the hopper cover. Slowly pour the two gallons (7.6 liters) of sanitizing solution into the mix hopper until the hopper becomes 1/4 full of sanitizing solution. Figure 40 Figure 38 Step 11 With the brushes provided, brush-clean the mix hopper, mix inlet hole, mix level float switch, product fitting, CO2 fitting and mix feed tube. Use caution when cleaning the float switch so as not to damage it. Figure 41 Figure 39 Models 345, 346, 349, 355 Figure 42 31 Operating Procedures Step 14 Press the BEATER key. Agitate the solution in the freezing cylinder for five minutes. Figure 43 Step 12 Install the mix feed tube into the mix inlet hole in the bottom of the mix hopper. Figure 46 Step 15 With a pail beneath the door spout, open the draw valve and drain all the solution from the mix hopper and the freezing cylinder. Press the OFF key and close the draw valve. Figure 44 Step 13 Sanitize and install the hopper cover. Lock the cover into place. Attach the vinyl tube to the pressure relief valve on the hopper cover. Position the open end of the vinyl tube into the rear drip pan. Figure 47 Step 16 Disconnect the syrup connector in the sanitizing solution. Repeat Steps 2 through 14 for the remaining freezing cylinder(s). Step 17 Remove the right side panel and install the rear white drip pan. Figure 45 Operating Procedures 32 Models 345, 346, 349, 355 Priming/Brixing Step 3 Raise the prime plug enough to allow a slight hissing sound. Step 1 Connect the syrup line to the syrup tank (or the Bag in Box). Step 2 Press the BEATER key to pressurize the freezing cylinder. Figure 50 Note: The pressure in the freezing cylinder should be relieved very slowly. Step 4 Slowly open the syrup sampling valve and let it run into a bucket until all the sanitizer is removed and full strength product is flowing. Do not open the valve so much that the syrup line to the hopper is drained. Figure 48 After three minutes, press the PRIME key. This will cause the product to flow to the mix hopper. Figure 51 Brix is the ratio of syrup to water which will directly affect the quality and taste of the product. Brixing should be done before priming the freezer and when a change in syrup flavor has been made. Figure 49 Models 345, 346, 349, 355 33 Operating Procedures Allow the product to flow over the refractometer. The brix reading should register 13 to 14. A reading higher than this would cause a darker, richer product. The refrigeration system would have to run longer to freeze this excess syrup. A reading lower than this could cause a freeze-up in the freezing cylinder because of the excess water. Figure 54 Step 6 With a pail beneath the door spout, press the BEATER key. Open the draw valve and drain the freezing cylinder. Close the draw valve. After three minutes, press the PRIME key. This will cause the product to flow to the mix hopper. Step 7 Hold a large cup under the pressure relief port exit of the door, until the liquid level (not foam) reaches the pressure relief port. Lower the prime plug. Press the OFF key. Figure 52 To adjust the brix, turn the adjustment screw located in the service panel. Clockwise adjustments increase the amount of syrup to water, and counterclockwise adjustments decrease the amount of syrup to water. Adjust the screw in small increments and check the brix again. Note: A large amount of foam indicates that the prime plug was raised too high. Repeat Steps 1 through 7 for the remaining freezing cylinder(s). Step 8 To place the freezing cylinder in the AUTO mode, press the AUTO key. When the unit cycles off, the product will be at serving viscosity. Figure 53 Repeat this step until a correct brix reading is registered. Step 5 Once the proper brix has been achieved, close the sampling valve. Install the front drip tray and the splash shield on the front of the freezer. Operating Procedures Figure 55 Repeat this step for the remaining freezing cylinder(s). 34 Models 345, 346, 349, 355 Step 2 When all the product has been drained from the mix hopper and the freezing cylinder, close the draw valve and press the OFF key. Discard this product. Step 9 Replace the side panels and close the lighted display. Install the hood in position on top of the freezer. 90 Day Closing Procedure We recommend that the machine be completely disassembled and cleaned at least every ninety days using the following procedures. ALWAYS FOLLOW LOCAL HEALTH CODES Figure 57 To disassemble a freezer, the following items will be needed: S S S S Repeat Steps 1 and 2 for the remaining freezing cylinder(s). Two cleaning pails Necessary brushes (provided with freezer) Cleaner Single service towels Cleaning Step 1 Open the lighted display door from the front of the machine. Remove the hood and side panels to gain access to the hoppers. Draining Product From the Freezing Cylinder Step 2 Prepare two gallons (7.6 liters) of an approved cleaning solution (example: Kay-5R). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Step 1 Press the BEATER key. This will allow the beater to operate and CO2 pressure will be maintained to push the product from the freezing cylinder. Open the draw valve and drain the product from the machine until the CO2 begins to jet. Important: Make sure the cleaner is completely dissolved. Step 3 Pour the solution into a clean, empty bucket. Place the syrup line with old syrup connection into the bucket of sanitizer. Step 4 Press the PRIME key. This will cause the cleaning solution to flow through the lines and into the mix hopper. Step 5 Remove the front drip tray. Place a mix pail beneath the sampling valve located behind the front drip tray. Slowly open the sampling valve and allow cleaner to flow through this line and out into the pail. After approximately 1/2 gallon of cleaner has been dispensed, close the valve. Figure 56 Models 345, 346, 349, 355 35 Operating Procedures Disassembly Step 6 Raise the prime plug. Place an empty pail under the door spout. When cleaning solution begins to exit the relief port opening in the freezer door, lower the prime plug. Press the OFF key. Open the draw valve and relieve all pressure from the freezing cylinder. Remove the hopper cover. Remove the mix feed tube and take it to the sink for further cleaning. Close the prime plug. Step 1 Be sure the control switch is in the OFF position. Open the draw valves to make sure all pressure has been relieved. Step 2 Raise the prime plug. Leave the bleed port open when removing the freezer door to insure that all pressure is relieved from the freezing cylinder. Step 7 Prepare two gallons (7.6 liters) of an approved cleaning solution (example: Kay-5R). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Step 3 Remove the following parts from the freezer and take them to the sink for brush-cleaning: handscrews, freezer doors, beater assemblies and scraper blades, drive shafts, hopper covers, front drip tray, splash shield. Step 8 Slowly pour two gallons (7.6 liters) of cleaning solution into the mix hopper until the hopper becomes 1/4 full of cleaning solution. Brush Cleaning Step 1 Prepare a sink with an approved cleaning solution. USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS (example: Kay-5R). IMPORTANT: Follow the label directions. Too STRONG of a solution can cause parts damage, while too MILD of a solution will not provide adequate cleaning. Make sure all brushes provided with the freezer are available for brush cleaning. Step 9 With the brushes provided, brush-clean the mix hopper, mix inlet hole, mix level float switch, product fitting, and CO2 fitting. Use caution when cleaning the float switch. Failure to do so will cause damage to the component. Step 2 Return to the freezer with a small amount of cleaning solution. With a single service towel, wipe clean the bearing surface. Brush-clean the rear shell bearings at the back of the freezing cylinders with the black bristle brush. Step 10 Clean and install the hopper cover. Lock the cover into place. Attach the vinyl tube to the pressure relief valve on the hopper cover. Position the open end of the vinyl tube into the rear drip pan. Step 11 Press the BEATER key to agitate the solution in the freezing cylinder. Step 12 With a pail beneath the door spout, open the draw valve and drain all the solution from the mix hopper and the freezing cylinder. Press the OFF key and close the draw valve. Step 13 Disconnect the syrup connector. Figure 58 Step 3 Remove the rear drip pan. (Does not apply to the Model 349.) Repeat Steps 2 through 13 for the remaining freezing cylinder(s). Operating Procedures 36 Models 345, 346, 349, 355 Note: To remove o-rings, use a single service towel to grasp the o-ring. Apply pressure in an upward direction until the o-ring pops out of its groove. With the other hand, push the top of the o-ring forward. It will roll out of the groove and can be easily removed. If there is more than one o-ring to be removed, always remove the rear o-ring first. This will allow the o-ring to slide over the forward rings without falling into the open grooves. Step 4 Remove the right side panel and take the rear, white drip pan to the sink for further cleaning. Step 5 Remove the following parts: seals and o-rings from the drive shafts, drive shaft seal bushings from drive shaft seals, caps and springs from freezer doors, screws and draw handle slides from freezer doors, pivot pins from draw valves, draw valve handles from freezer doors, draw valves from freezer doors, o-rings from draw valves, prime plugs from freezer doors, o-rings from prime plugs, o-rings and front bearings from freezer doors, o-rings from mix hopper covers. Step 6 Using a single service towel, wipe the lubricant off the parts. Brush-clean all disassembled parts in the cleaning solution. Make sure all lubricant and syrup is removed. Place all the cleaned parts on a clean, dry surface to air-dry. Step 7 Wipe clean all the exterior surfaces of the freezer. Discard all o-rings and replace them with new ones. Models 345, 346, 349, 355 37 Operating Procedures Section 7 Important: Operator Checklist During Cleaning and Sanitizing j 7. Clean and sanitize the syrup lines regularly to prevent syrup residue build-up that would restrict the proper flow of syrup. j 8. On a regular basis, take a brix reading to assure a consistent quality product. ALWAYS FOLLOW LOCAL HEALTH CODES Cleaning and sanitizing schedules are governed by your State or local regulatory agencies and must be followed accordingly. The following check points should be stressed during the cleaning and sanitizing operations. Regular Maintenance Checks WE RECOMMEND CLEANING AND SANITIZING EVERY 90 DAYS. Troubleshooting Bacterial Count j 1. Replace scraper blades that are nicked, damaged or worn down. j 1. Thoroughly clean and sanitize the machine regularly, including complete disassembly and brush cleaning. j 2. Before installing the beater, be certain that the scraper blades are properly attached over the pins. j 2. Use all brushes supplied for thorough cleaning. The brushes are specially designed to reach all product passageways. j 3. Check the rear shell bearing for signs of wear (excessive product leakage from the rear drip pans to the front drip tray). j 3. Use the white bristle brush to clean the mix inlet hole which extends from the mix hopper down to the rear of the freezing cylinder. j 4. Dispose of o-rings or seals if they are worn, torn, or fit too loosely, and replace with new ones. j 4. Use the black bristle brush to thoroughly clean the rear shell bearing located at the rear of the freezing cylinder. Be sure there is a generous amount of cleaning solution on the brush. j 5. Follow all lubricating procedures as outlined in “Assembly”. j 5. Using a screwdriver and a cloth towel, keep the rear shell bearing and the female hex drive socket clean and free of lubricant and product deposits. j 6. Check the condenser(s) for accumulation of dirt and lint. Dirty condensers will reduce the efficiency and capacity of the machine. Condensers should be cleaned monthly by removing the poly- flo filter and cleaning it. Remove the service panel and side panels to expose the condenser(s). Never use screwdrivers or other metal probes to clean between the fins. j 6. Properly prepare the cleaning and sanitizing solutions. Read and follow the label directions carefully. Too strong of a solution may damage the parts and too weak of a solution will not do an adequate job of cleaning or sanitizing. Important: Operator Checklist 38 Models 345, 346, 349, 355 Winter Storage If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is subject to freezing conditions. Wrap detachable parts of the freezer such as the beater, the scraper blades, the drive shaft, and the freezer door. Place these parts in a protected, dry place. Rubber trim parts and gaskets can be protected by wrapping them with moisture-proof paper. All parts should be thoroughly cleaned of dried mix or lubrication which attract mice and other vermin. Disconnect the freezer from the main power source to prevent possible electrical damage. Note: It is recommended that an authorized service technician perform winter storage draining, to insure all water has been removed. This will guard against freezing and rupturing of the components. Your local Taylor Distributor can perform this service for you. Models 345, 346, 349, 355 39 Important: Operator Checklist Section 8 PROBLEM 1. Product is too stiff. Troubleshooting Guide PROBABLE CAUSE REMEDY PAGE REF. a. Too much water to syrup ratio. Improper brix adjustment. a. Adjust the brix accordingly. b. Consistency control needs adjustment. b. Contact a service technician. - - - c. Torque coupling bound in WARM position. c. Contact a service technician. - - - a. Freezer in a defrost cycle. a. Wait for defrost cycle to end. - - - b. Consistency control needs adjustment. b. Contact a service technician. - - - c. Torque coupling bound in COLD position. c. Contact a service technician. - - - d. Broken springs in torque coupling. d. Contact a service technician. - - - 3. No product is being dispensed. a. Product frozen-up in freezing cylinder. a. See problem No. 1. - - - 4. Freezer will not operate in the BEATER or AUTO mode. a. Unit is unplugged. a. Check the plug at wall receptacle. - - - b. Blown fuse, or the circuit breaker is off. b. Replace the fuse or turn the breaker on. - - - c. Beater motor is out on overload. Check fault description screen. c. Allow the motor to cool. Press the AUTO key. Call a service technician if the beater motor goes out on overload again. 18 a. Beater motor is out on overload. Check the fault description screen. a. Allow the motor to cool. Press the AUTO key. Call a service technician if the beater motor goes out on overload again. 18 b. The torque coupling is bound in the COLD position. b. Contact a service technician. c. Condenser dirty, A/C. c. Clean condenser monthly. d. Water supply off, W/C. d. Turn the water on. 2. Product is too soft. 5. No compressor operation in the AUTO mode. Troubleshooting Guide 40 33 - - - 38 - - - Models 345, 346, 349, 355 PROBLEM PROBABLE CAUSE REMEDY PAGE REF. a. Rounded corners of hex end of drive shaft, drive coupling, or both. a. Replace the drive shaft, or call a service technician to replace the direct drive unit. - - - b. Lubrication of hex end of drive shaft. b. Do not lubricate the hex end. If necessary, contact a service technician for removal. 24 7. Excessive loss of CO2. a. Leak in the CO2 system. a. Contact a service technician. 8. Leakage from rear drip pan(s) into front drip tray. a. Seal or o-ring on drive shaft is worn, missing, or incorrectly installed. a. Replace or install correctly on drive shaft. 24 b. Worn rear shell bearing. b. Contact a service technician to replace rear shell bearing. - - - a. Inadequate lubrication of draw valve o-rings. a. Lubricate properly. 26 b. Wrong type lubricant on draw valve o-rings. b. Use food grade lubricant (example: Taylor Lube HP). 24 c. Worn or missing draw valve o-rings. c. Replace or install o-rings on draw valve. 26/ 42 a. Syrup lines need to be cleaned and sanitized. a. Clean and sanitize syrup lines. - - - b. Blocked flow control. b. Contact a service technician. - - - a. Loss of CO2 to propel syrup. a. Contact a service technician. - - - b. Clogged or kinked syrup lines. b. Sanitize syrup lines regularly. If kinked, repair or replace. - - - a. Machine is not in the AUTO or PRIME mode. a. Place the machine in the AUTO or PRIME mode. 34 b. The mix level float switch is inoperative. b. Contact a service technician. - - - a. Faulty check valve in carbonation system. a. Call a service technician to replace the check valve. - - - 6. Unable to remove the drive shaft from the rear shell bearing. 9. Excessive mix leakage from door spout. 10. Unable to adjust brix. 11. Lack of syrup being supplied to machine. 12. Product does not enter mix hopper. 13. Carbonated water or sulfuric aroma is evident in the faucet or sewage system. Models 345, 346, 349, 355 41 - - - Troubleshooting Guide Section 9 PART DESCRIPTION Parts Replacement Schedule EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY X Minimum Black Bristle Brush, 1” x 2” Inspect & Replace if Necessary Minimum Double Ended Brush Inspect & Replace if Necessary Minimum White Bristle Brush, 1-1/2” x 2” Inspect & Replace if Necessary Minimum White Bristle Brush, 3” x 7” Inspect & Replace if Necessary Minimum Scraper Blade Drive Shaft Seal X Drive Shaft O-Ring X Freezer Door O-Ring X Draw Valve O-Ring X Door Spout O-Ring X Hopper Cover O-Ring X Front Bearing X Prime Plug O-Ring X Refer to Parts List on the next page when ordering the above parts. Parts Replacement Schedule 42 Models 345, 346, 349, 355 Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”) to the original purchaser only. LIMITED WARRANTY Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of this document. Product Soft Serve Frozen Yogurt Shakes Smoothies Frozen Beverage Batch Desserts Part Limited Warranty Period Insulated shell assembly Five (5) years Refrigeration compressor (except service valve) Five (5) years Beater motors Two (2) years Beater drive gear Two (2) years Printed circuit boards and Softech controls beginning with serial number H8024200 Two (2) years Parts not otherwise listed in this table or excluded below One (1) year LIMITED WARRANTY CONDITIONS 1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of purchase may be required at time of service. 2. This limited warranty is valid only if the Product is installed and all required service work on the Product is performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are used. 3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the Taylor Operator’s Manual. 4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit. 5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty. LIMITED WARRANTY EXCEPTIONS This limited warranty does not cover: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective parts, replacement parts, or new Products. 2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning of condensers. 131122 Models 345, 346, 349, 355 43 Limited Warranty on Equipment 3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual. 4. External hoses, electrical power supplies, and machine grounding. 5. Parts not supplied or designated by Taylor, or damages resulting from their use. 6. Return trips or waiting time required because a service technician is prevented from beginning warranty service work promptly upon arrival. 7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies. 8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or water supply specification of the Product; or components repaired or altered in any way so as, in the judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration. 9. Any Product purchased over the Internet. 10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of electrical service. 11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever. 12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will void this limited warranty. 13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant. 14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER. LEGAL REMEDIES The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072 Limited Warranty on Equipment 44 Models 345, 346, 349, 355 Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally (the “Parts”) to the original purchaser only. LIMITED WARRANTY Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of this document. Limited Warranty Period Part’s Warranty Class Code or Part Class 103 Parts¹ Three (3) months Class 212 Parts² Twelve (12) months Class 512 Parts Twelve (12) months Class 000 Parts No warranty Taylor Part #072454 (Motor- 24VDC *C832/C842*) Four (4) years LIMITED WARRANTY CONDITIONS 1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required at time of service. 2. This limited warranty is valid only if the Part is installed and all required service work in connection with the Part is performed by an authorized Taylor distributor or service agency. 3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation location in the unit of original installation. 4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the Taylor Operator’s Manual. 5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit. 6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate Taylor Limited Warranty on freezer or grill equipment. 7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited warranty. 1, 2 Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1 (Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment. 131122 Models 345, 346, 349, 355 45 Limited Warranty on Parts LIMITED WARRANTY EXCEPTIONS This limited warranty does not cover: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective Parts, replacement Parts, or new Parts. 2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning of condensers or carbon and grease buildup. 3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but not limited to the platen and plate, sides of the shroud or top of the shroud. 4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials or cleaning processes not approved for use by Taylor. 5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any release sheets and clips for the Product’s upper platen assembly. 6. External hoses, electrical power supplies, and machine grounding. 7. Parts not supplied or designated by Taylor, or damages resulting from their use. 8. Return trips or waiting time required because a service technician is prevented from beginning warranty service work promptly upon arrival. 9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies. 10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or water supply specification of the unit in which a part is installed; or Parts or the units in which they are installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or normal wear or deterioration. 11. Any Part purchased over the Internet. 12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of electrical service. 13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever. 14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited warranty. 15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant. 16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. Limited Warranty on Parts 46 Models 345, 346, 349, 355 LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER. LEGAL REMEDIES The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072 Models 345, 346, 349, 355 47 Limited Warranty on Parts Parts List 032511 Bearing- Rear Shell 48 041182 Beater Assembly X30160 046536- Housing A.- W/Wheel Motor- Blower X47833- Blower Assembly 033047 053726 Wheel- Blower Capacitor- Run 053729 Screen- Blower X53725- 27 Blower A. 053481- 27 039422 Block- Terminal 2P- L1,L2 053728 039422 Block- Terminal 2P- L1,L2 Motor- Fan 208- 230V 50/60 HZ 033145 Belt (Rear Bearing Units) Housing- Blower- 6 POLE 044056 Belt 053720 033142 Belt Clip- Screen- Blower 025633 Belt 041103 X39163- SER Bearing- Unit Rear (2 Pulley) +Blade- Scraper X39162- SER Bearing- Unit Rear (1 Pulley) 012864 X49506 Accumulator A.- Insulated +Washer- Bearing Lock 053377 Accumulator- Copper 2”DIA 13”LG 018432 X50468 Accumulator A.- Insulated- Right +O- Ring X50465 Accumulator A.- Insulated- Left 028991 X50139 Accumulator A.- Insulated- Right 028992 X50138 Accumulator A.- Insulated- Left +Nut- Brass Bearing 047062 Accumulator- Copper 2” Dia. 10” Long +Guide- Drip Seal 042134 X50261 PART NUMBER +Accumulator- Suction- Vertical Accumulator A.- Insulated DESCRIPTION 1 1 2 4 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 4 1 2 2 2 4 2 2 2 2 2 2 2 1 1 2 1 1 1 1 1 1 1 1 4 1 3 1 2 2 8 4 2 2 4 4 4 4 4 1 1 2 1 1 1 4 2 1 1 2 2 2 2 2 1 1 345 346 349 355 QTY. QTY. QTY. QTY. 103 103 103 103 103 103 103 103 103 103 103 103 000 000 000 000 000 103 103 103 000 000 000 000 000 103 103 103 103 103 103 103 103 103 WARR. CLASS Prior to: 346- K0066159, 349- K0053129 346- K0066159/Up, 349- K0053129/Up Prior to: 349- J9097086, 355- J8113767 349- J9097086/Up, 355- J8113767 Kit- Includes Retaining Plate- 052131 Kit- Includes Retaining Plate- 052131 Prior to J9053838 0355- J9053838/Up Prior to J9114879 Prior to J9114879 Prior to J9072433 Prior to J9072433 345- J9067375/Up, 346- J9072433/Up, 349- J9114879/Up Prior to J9067375 Prior to J9067375 REMARKS 126 129 144 144 144 PARTS UPDATE Section 12 Parts List + Available Separately Models 345, 346, 349 & 355 + Available Separately Models 345, 346, 349 & 355 49 Parts List 014753 023316 040040- 010 040040- 011 040040- 042 040040- 043 040040- 041 040040- 015 040040- 019 049455- 27 Brush- White Bristle Brush- White Bristle (3” x 7”) Cable- Ribbon- 50C (5”) Cable- Ribbon- 50C (20”) Cable- Ribbon- 20C (18”) Cable- Ribbon- 20C (18”) Cable- Ribbon- 20C (14”) Cable- Ribbon- 14C (14”) Cable- Ribbon- 14C (22”) Carbonator 032571 +Lock- Caster Bracket 052401- 27 +Relay- Compressor 037430 +Relay- Start- Compressor 029439 048134 +Capacitor- Run - 35MFD/375V +Capacitor- Start - 124- 147MFD/330V 047520- 031790 +Capacitor- Start - 161- 193UF/250V Compressor (TECUMSEH) 037431 +Capacitor- Run - 25UF/440V 036880- 053106 +Capacitor- Start 189- 227UF/250V Compressor (BRISTOL) 029439 +Capacitor- Run 35UF/370V 052396- 030307 Caster- Locking Swivel (Front) Compressor (COPELAND) 035324 Card- Flavor (Packet of 9 Cards) 021279 043957 Card- FCB P.O.P. Caster- Swivel (Rear) 032569 Carbonator (OLD) 050257- 27 013072 Probe A.- Carbonator w/Reed Switch 013071 Brush- Double Ended PART NUMBER Brush- Black Bristle (1” x 2”) DESCRIPTION 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 345 QTY. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 346 QTY. 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 349 355 QTY. QTY. 103 103 512 103 103 103 512 103 103 103 512 103 103 103 000 000 103 103 103 103 103 103 103 103 103 103 000 000 000 000 WARR. CLASS 230- 60- 1 230- 60- 1 Replacement for 036880- 230- 60- 1 230- 60- 1 230- 60- 1 355 - For Service - Use X53905- 27 (Modifications Required - SB 2507) Prior to: 345- J9067375, 346- J9067641, 349- J9097086, 355- J9053838. For Service- Use 047520- & the applicable start components. 230- 60- 1 230- 60- 1 230- 60- 1 349- J9097086/Up 345- J9067375/Up 346- J9067641/Up Jo Bell - Prior to J5061557 230- 60- 1 McCann - J5061557/Up REMARKS 150 140/141 144 144 144 144 95 103, 119 95, 119 PARTS UPDATE + Available Separately Parts List 50 Models 345, 346, 349 & 355 020944- 24 039365 039416 043636- L 052898 Tube- Vinyl Drain Valve- Pressure Relief Decal- Cleaning Instructions Decal- Left Control Decal- Left Control 016037 042079 Cover- Hopper O- Ring- Hopper Cover 042610 Clamp- Hose X42080 Cover A.- Mix Tank- Relief Valve 049285- RED Label- Identification- Red 053290 039734 Spring - Red Cover- Compressor 039455 Screw- Shoulder 052816 025376 Screw- Set Cover- Compressor 039453 Pin- Coupling Torque X39523 Coupling A.- Torque 039397 053376 Condenser A/C 046866 019558 Condenser A/C Coupling- Load Torque 052502- 2 Condenser- AC- 12LX18HX3.12T 5RW Coupling- Drive Torque 053502- 1 +Capacitor- Run - 20UF/440V Condenser- AC- 12LX18HX3.12T 5RW 012906 051957- 27 +Relay- Start- Compressor INCLUDES: 033044- 1 X53292- 27 051958- 048150 PART NUMBER +Capacitor- Start - 189- 227UF/330V +Box A.- Cap/Relay Compressor (COPELAND) +Relay- Start- Compressor DESCRIPTION 1 1 1 2 2 2 2 2 2 1 2 6 6 4 6 2 2 2 1 1 345 QTY. 1 1 1 2 2 2 2 2 2 2 6 6 4 6 2 2 2 2 1 1 2 346 QTY. 1 4 4 4 4 4 4 2 4 12 12 8 12 4 4 4 2 1 1 2 1 1 1 2 2 2 2 2 2 1 2 6 6 4 6 2 2 2 1 1 1 1 1 1 349 355 QTY. QTY. 000 000 000 103 000 000 103 000 103 103 103 000 103 000 000 103 103 103 103 103 103 103 103 103 103 103 103 512 103 WARR. CLASS 345- J9053838/Up, 346- J9072433/Up, 355- J9012316/Up Prior to: 345- J9053838 346- J9072433, 355- J9012316 Bulk under R30335 Sound Barrier - J9053838/Up Sound Barrier - J9067375/Up Replaces 047083 Prior to: 346- J9072433 349- J9097086 Front- Right Shell 346- J9072433/Up 349- J9097086/Up Rear- Left Shell 346- J9072433/Up 349- J9097086/Up 230- 60- 1 230- 60- 1 230- 60- 1 230- 60- 1 - J9053838/UP J9053838/Up - HP62 Also replacement for 036880- Must convert to HP62 Refrigerant & install 049154 Dryer. See Update 142 230- 60- 1 REMARKS 142 142 144 139 142 142 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 51 Parts List 045967 043892 053646 043467 042941 039463 038374 046586 X53549 X53593 053515044939053566 044940053636043502S052840044107X38062- SER Decal- Decorative Decal- Decorative ”Taylor Crown/Logo” Decal- Dec- Slush- Press- 4 BRL Decal- Decorative Decal- Power Switch Decal- Pressure Gauge (Set of 4) Decal- Troubleshooting Deflector- Blower Exhaust Deflector A.- Air Exhaust *346* Deflector A.- Air Exhaust *349* Diagram- Wiring Diagram- Wiring Diagram- Wiring *346* Diagram- Wiring Diagram- Wiring *349* Diagram- Wiring Diagram- Wiring Diagram- Wiring Display- Liquid Crystal 046190 046193- BLA +Slide- Draw Handle 046190- BLA 053869 +Screw +Spout- Door 017003 +O- Ring +Spout- Door 046192 +Handle- Draw Valve 046193 046192- BLA +Handle- Draw Valve +Slide- Draw Handle 039349 039573 +Bearing- Front Door- Freezer 038221 053761 +Lens- Display 043636- R Decal- Dec- Taylor Domed PART NUMBER Decal- Right Control DESCRIPTION 2 2 4 4 4 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 345 QTY. 2 2 4 4 4 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 346 QTY. 4 4 8 8 8 4 4 4 4 4 1 1 1 1 1 1 1 2 1 1 1 1 2 2 4 4 4 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 349 355 QTY. QTY. 103 103 103 103 000 000 103 103 000 103 103 103 000 000 000 000 000 000 000 103 103 103 000 000 000 000 000 000 000 000 000 WARR. CLASS Prior to J8060000 J8060000/Up Prior to J8060000 J8060000/Up Prior to J8060000 J8060000/Up Prior to J9053838 355- J8113767/Up Prior to J9114233 J9114233/Up Prior to J9072433 J9072433/Up Prior to J9067375 J9067375/Up J9071741/Up J9072433/Up Prior to: 346- J9072433, 346- J9071741 Prior to J9114233 349- J6114233/Up Prior to J8060000 (Dec Plate- X44115- BLA) J8060000 to: 345- K0012597, 346- K0024873 349- K0025070, 355- K0013505 349- K0025070/Up, 355- K0013505/Up 345- K0012597/Up, 346- K0024873/Up, REMARKS 130 130 151 130 142 144 144 130 PARTS UPDATE + Available Separately Parts List 52 Models 345, 346, 349 & 355 052779- 1 Filter- Air- 18.00LX16.50HX.70W 043638 Regulator (0 - 100 PSI) 2 +Body A.- Flow Control - Less Solenoid X48729- SER 2 2 2 1 1 1 1 1 1 1 1 1 1 4 2 2 2 4 2 2 2 345 QTY. (Or X48729- SER - Body A.- Flow Control w/o Solenoid) X48729- 27 043638 Regulator (0 - 100 PSI) Body A.- Flow Control w/Solenoid 043643 Gauge- Pressure (0 - 100 PSI) X48728- 27 018466 Fitting 3/8 x 1/4 Flow Control - w/o Pressure Switch 029235 Filter- Water Line X42151 043643 Filter A.- Regulator 018466 Gauge- Pressure (0 - 100 PSI) X35019 Filter A.- Regulator Fitting 3/8 x 1/4 044734 Filter- Water (Carbonator) 029235 053697 Filter- Water 1/4FFLINX1/4MFLOV Filter- Water Line 040140- 001 Filter- Corcom 053801 049154 Dryer- Filter +Cover- Hole- Filter- Snap In 045866 016369 +O- Ring 048901 039324 +Valve- Draw Dryer- Filter 039320 +Spring Dryer- Filter- HP62- 3/8 X 1/4S 039321 +Pin- Pivot 046138 039219 +O- Ring Dryer- Filter 039323 +Nut- Spout 049154 046191 Dryer- Filter 046191- BLA +Cap PART NUMBER +Cap DESCRIPTION 2 2 2 2 1 1 1 1 1 1 1 1 2 2 2 2 4 2 2 2 4 2 2 2 346 QTY. 4 4 4 4 1 1 1 1 1 1 1 1 2 2 2 2 8 4 4 4 8 4 4 4 2 2 2 1 1 1 4 2 2 2 4 2 2 2 349 355 QTY. QTY. 103 103 103 103 103 103 103 000 103 103 103 103 000 103 000 000 103 000 000 000 000 000 000 000 000 103 103 103 000 103 103 103 WARR. CLASS Less Pressure Switch Prior to J9114233 Prior to: 345- J9067375, 346- J9067641 Prior to: 345- J9102846, 346- J9102432, 349- J9102424 345- J9102846/Up, 346- J9102432/Up 349- J9102424/Up 346- J9072433/Up, 349- J9097086/Up 349- J9097086/Up, 355- J9012316/Up Prior to J9067641 346- J9067641/Up Prior to: 345- J8124526, 349- J90097086, 355- J9012316 J8124526/Up Prior to J8060000 J8060000/Up REMARKS 144 142 144 144 130 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 53 Parts List 051826- 155 051826- 168 018520 018521 030386 018595 Hose- Beverage Hose- Beverage Marker- No. 1 Marker- No. 2 Valve- Check Washer- Nylon Flare 016715 018520 018521 018522 018523 Adaptor- Swivel Marker- No. 1 Marker- No. 2 Marker- No. 3 Marker- No. 4 X52457 051826- 146 Hose- Beverage Harness A.- Feed 049427 X49312 Harness A.- Feed Fitting X47137 Guide A.- Drip Pan 052140 X47134 Ferrule 045606 +Holder- Fuse Guide A.- Drip Pan 044519 045293 Fuse 15 Amp - In Line Label- CO2 016137 +O- Ring- Plug 016715 1 049573 +Plug- Pressure Switch Adaptor- Swivel 1 049706 +Switch- Pressure 15 PSI 2 2 2 2 1 1 1 2 6 2 4 1 1 2 2 2 2 048784 4 30 +Switch- Pressure 35 PSI 048709 Screw- 8 x 1/2 SL Hex 2 041951 048829 Retainer- Inlet Line 4 4 2 30 2 4 345 QTY. Screw- 8- 32 x 3/8 Hex 016137 X48732 Bowl A.- Float- Flow Control O- Ring- Flow Control Float A. 048709 Screw- 8 x 1/2 SL Hex 048710 048829 Clip- Retainer- Syrup Pressure Switch 048776- 27 Retainer- Inlet Line PART NUMBER Coil- Solenoid DESCRIPTION 2 2 2 2 1 1 1 2 6 2 4 1 1 1 1 2 2 4 2 4 12 2 4 2 2 24 2 4 346 QTY. 2 2 2 2 6 1 2 2 4 4 4 4 8 24 4 8 4 4 48 4 8 1 1 1 2 2 2 2 4 12 2 4 2 2 24 2 4 349 355 QTY. QTY. 000 000 000 000 103 103 000 103 000 000 000 000 000 103 000 000 103 103 103 103 103 000 000 103 103 103 000 000 103 000 103 103 000 103 103 WARR. CLASS J8050000/Up (Replaces X49313) Bulk - R30313 Bulk - R30313 Bulk - R30313 non- pressurized units only non- pressurized units only non- pressurized units only REMARKS 130 128 PARTS UPDATE + Available Separately Parts List 54 Models 345, 346, 349 & 355 030386 051826- 180 051826- 210 044519 049427 Valve- Check Hose- Beverage Hose- Beverage Label- CO2 Fitting 045199 049428 021030 051826- 120 051826- 188 051826- 8 018520 018521 018522 018523 019762 030386 049429 018595 Decal- Soda Elbow Ferrule Hose- Beverage Hose- Beverage Hose- Beverage Marker- No. 1 Marker- No. 2 Marker- No. 3 Marker- No. 4 Tee Valve- Check Valve- Check Washer- Nylon Flare 039349 039219 016369 025307 017003 016037 029751 048260- WHT O- Ring (Door Spout) O- Ring (Draw Valve) O- Ring (Drive Shaft) O- Ring (Freezer Door) O- Ring (Hopper Cover) O- Ring (Prime Plug) O- Ring Removal Tool X39699 Kit A.- Tune- Up Bearing- Front 042166 Hood 044618 016715 Adaptor- Swivel Hood 018646 Adaptor X51823 052140 Harness A.- Feed 018595 Ferrule PART NUMBER Washer- Nylon Flare DESCRIPTION 1 4 2 2 2 4 4 2 2 1 345 QTY. 2 4 2 2 2 4 4 2 2 1 346 QTY. 4 8 4 4 4 8 8 4 4 1 4 2 1 4 4 10 4 2 4 2 2 2 4 4 2 2 1 4 2 2 1 2 2 3 3 2 2 3 14 2 3 8 1 1 349 355 QTY. QTY. 000 000 000 000 000 000 000 000 000 103 103 000 103 103 103 000 000 000 000 000 000 000 000 103 000 103 103 103 103 000 000 000 103 000 000 WARR. CLASS Bulk - R30313 Bulk - R30313 REMARKS 128 128 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 55 Parts List 051433 042279 039462 051807 036397 Label- Warning- Cover Label- Warning- Do Not Draw Product Label- Warning- Relieve Pressure LED Assembly (Product Not Ready) Leg- 4” 016715 052140 051826- 65 Adaptor- Swivel Ferrule Hose- Beverage 052140 051826- 24 Ferrule Hose- Beverage 051826- 50 Hose- Beverage 051826- 8 Hose- Beverage 2 051826- 9 016715 052140 018520 Ferrule Marker- No. 1 X52453 4 2 2 4 4 2 1 2 2 2 1 1 1 2 2 7 1 2 345 QTY. 052140 Adaptor- SWV 1/4F 1/4Barb*SS* Line A.- CO2 (No. 1) Hose- Beverage Ferrule X43656 052140 Ferrule Line A.- CO2 (Right & Left) (OLD) 016715 Adaptor- Swivel X53880 052140 Ferrule Line A.- CO2 (Right & Left) (NEW) 016715 Adaptor- Swivel X44518 044519 Label- CO2 Line A.- CO2 (Regulator to Carbonator) 016715 Adaptor- Swivel X44952 X28150 Line A.- Air Supply Line A.- CO2 (Regulator to Carbonator) 051751 Lens- Yellow 039268 032749 Label- Door- Warning- Moving Parts +Cap- Rubber 032164 032560 PART NUMBER Label- Caution- GRD- PERM- ENG/SP Seal (Drive Shaft) DESCRIPTION 2 4 2 2 4 4 2 1 2 2 2 1 2 1 2 2 8 1 1 2 346 QTY. 2 2 2 1 1 2 2 1 4 2 2 2 7 1 1 4 2 4 2 2 4 4 2 1 2 2 1 2 4 4 1 2 2 5 1 1 2 349 355 QTY. QTY. 000 000 103 103 000 000 103 000 000 103 103 000 000 103 103 000 000 000 103 103 000 000 103 103 103 000 103 103 000 000 000 000 000 000 WARR. CLASS J8050000/Up (Replaces X45182) Bulk - R30313 Use w/Old Style 2.5 Quart Mix Tank Bulk- R30313 Use w/New Style 3.5 Quart Mix Tank Bulk - R30313 Bulk - R30313 Bulk - R30313 LED Snap In - Replaces 042509- LensRed New Amber Light (Replaces X42508) To Prevent Injury 349- 4 prior to J8124111 w/Light Flashing 349- 4 prior to J8124111 Replaces 036529 Decal *CAUTION* 346- J9084947/Up, 349- J9097086/Up, 355- J9012316/Up REMARKS 130 128 151 151 128 128 128 136 PARTS UPDATE + Available Separately Parts List 56 Models 345, 346, 349 & 355 018521 051826- 27 Marker- No. 2 Hose- Beverage 018522 051826- 28 Marker- No. 3 Hose- Beverage 018523 051826- 29 Marker- No. 4 Hose- Beverage 051826- 36 Hose- Beverage 051826- 3 051826- 32 051826- 40 051826- 42 018520 019762 031622 Hose- Beverage Hose- Beverage Hose- Beverage Hose- Beverage Marker- No. 1 Tee- 1/4 Barb- SS Valve- Sampling X49667 052140 Ferrule Line A.- Mix Outlet (Left & Right) 049428 020563 Elbow- 3/8 O- Ring x 1/4 Barb Elbow- 1/4 FFL x 1/4 Barb X49585 051826- 36 Hose- Beverage Line A.- Mix Outlet (Left) 052140 Ferrule X41005 052140 Ferrule Line A.- CO2- BIB Pump 016715 Adaptor- Swivel X31565 052140 Ferrule Line A.- CO2 (CO2 Tank to Syrup Tank) 016715 Adaptor- SWV 1/4F 1/4Barb*SS* X52456 052140 Ferrule Line A.- CO2 (No. 4) 016715 Adaptor- SWV 1/4F 1/4Barb*SS* X52455 052140 Ferrule Line A.- CO2 (No. 3) 016715 X52454 051826- 30 PART NUMBER Adaptor- SWV 1/4F 1/4Barb*SS* Line A.- CO2 (No. 2) Hose- Beverage DESCRIPTION 1 1 2 1 1 1 1 4 1 1 1 2 2 2 2 4 4 2 345 QTY. 1 1 2 1 1 1 1 6 1 1 1 2 2 2 2 4 4 2 346 QTY. 4 8 8 4 1 2 2 2 1 1 2 2 2 1 1 2 2 2 1 1 2 2 4 4 2 349 355 QTY. QTY. 103 103 103 000 000 000 000 000 000 103 103 103 000 000 103 000 000 103 103 000 000 000 103 103 000 000 000 103 103 000 000 000 103 103 000 WARR. CLASS Use w/New Style 3.5 Quart Mix Tank Use w/Old Style 2.5 Quart Mix Tank Bulk - R30313 Bulk - R30313 Bulk - R30313 Bulk - R30313 Bulk - R30313 (Replaces 051826- 4) J8050000/Up (Replaces X45185) Bulk - R30313 (Replaces 051826- 8) J8050000/Up (Replaces X45184) Bulk - R30313 (Replaces 051826- 9) J8050000/Up (Replaces X45183) Bulk - R30313 (Replaces 051826- 14) REMARKS 151 151 128 128 128/130 130 128/130 130 128/130 130 128/130 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 57 Parts List 051826- 42 051826- 40 018521 019762 031622 Hose- Beverage Hose- Beverage Marker- No. 2 Tee- 1/4 Barb SS Valve- Sampling 052140 051826- 5 051826- 38 051826- 36 051826- 48 018520 019762 031622 Ferrule Hose- Beverage Hose- Beverage Hose- Beverage Hose- Beverage Marker- No. 1 Tee Valve- Sampling 020563 049428 052140 051826- 3 051826- 5 Elbow- 1/4 FFL x 1/4 Barb Elbow- 3/8 O- Ring x 1/4 Barb Ferrule Hose- Beverage Hose- Beverage- 1/4 ID X 7/16 OD X49720 049428 Elbow- 3/8 O- Ring x 1/4 Barb Line A.- Mix Outlet (No. 2) 020563 Elbow- 1/4 FFL x 1/4 Barb X49719 051826- 32 Hose- Beverage Line A.- Mix Outlet (No. 1) 051826- 3 X49586 Line A.- Mix Outlet (Right) Hose- Beverage 031622 Valve- Sampling 052140 051826- 40 Hose- Beverage Ferrule 051826- 46 Hose- Beverage 049428 051826- 24 Hose- Beverage Elbow- 3/8 O- Ring x 1/4 Barb SS 052140 Ferrule 020563 049668 Elbow- 1/4 FFL x 1/4 Barb Swivel 020563 Elbow- 3/8 O- Ring x 1/4 Barb PART NUMBER Elbow- 1/4 FFL x 1/4 Barb DESCRIPTION 1 1 2 1 1 1 1 6 1 1 1 345 QTY. 1 1 2 1 1 1 1 6 1 1 1 346 QTY. 1 1 6 1 1 1 1 1 2 1 1 1 1 6 1 1 1 2 2 2 2 8 2 2 349 355 QTY. QTY. 000 000 000 103 103 103 103 103 000 000 000 000 000 000 103 103 103 103 103 000 000 000 000 000 000 103 103 103 103 000 000 000 000 103 103 WARR. CLASS Use w/New Style 3.5 Quart Mix Tank Use w/Old Style 2.5 Quart Mix Tank Use w/Old Style 2.5 Quart Mix Tank Use w/New Style 3.5 Quart Mix Tank Use w/Old Style 2.5 Quart Mix Tank Use w/New Style 3.5 Quart Mix Tank Use w/Old Style 2.5 Quart Mix Tank Use w/New Style 3.5 Quart Mix Tank REMARKS 151 151 151 151 PARTS UPDATE + Available Separately Parts List 58 Models 345, 346, 349 & 355 018521 019762 031622 Marker- No. 2 Tee- 1/4 Barb SS Valve- Sampling 052140 051826- 5 051826- 48 051826- 50 018522 019762 031622 Ferrule Hose- Beverage Hose- Beverage Hose- Beverage Marker- No. 3 Tee Valve- Sampling 051826- 38 051826- 36 051826- 48 018523 019762 Hose- Beverage Hose- Beverage Hose- Beverage Marker No. 4 Tee 052140 051826- 63 Ferrule Hose- Beverage 016715 045199 052140 Adaptor- Swivel Decal- Soda Ferrule X49587 016715 Adaptor- Swivel Line A.- Soda (Carbonator- Sentry) 018646 Adaptor- Barb X44961 051826- 5 Hose- Beverage Line A.- Pressure (Water) 052140 Ferrule 031622 049428 Elbow- 3/8 O- Ring x 1/4 Barb Valve- Sampling 020563 Elbow- 1/4 FFL x 1/4 Barb X49722 049428 Elbow- 3/8 O- Ring x 1/4 Barb Line A.- Mix Outlet (No. 4) 020563 Elbow- 1/4 FFL x 1/4 Barb X49721 051826- 50 Line A.- Mix Outlet (No. 3) 051826- 48 Hose- Beverage PART NUMBER Hose- Beverage DESCRIPTION 6 3 3 1 1 2 1 1 1 345 QTY. 6 3 3 1 1 2 1 1 1 346 QTY. 1 1 2 1 1 1 1 6 1 1 1 1 1 2 2 1 1 6 1 1 1 1 1 1 2 1 349 355 QTY. QTY. 000 000 103 103 000 000 103 103 103 103 103 000 000 000 000 000 000 103 103 103 103 103 000 000 000 000 000 103 103 103 103 103 000 000 000 WARR. CLASS Prior to: 345- J9067375, 346- J9056262 Use w/Old Style 2.5 Quart Mix Tank Use w/New Style 3.5 Quart Mix Tank Use w/New Style 3.5 Quart Mix Tank Use w/Old Style 2.5 Quart Mix Tank Use w/New Style 3.5 Quart Mix Tank Use w/Old Style 2.5 Quart Mix Tank REMARKS 144 151 151 151 151 151 151 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 59 Parts List 019762 049429 018595 Tee Valve- Check Washer- Nylon 020565- 28 Hose- Beverage 020565- 24 Tube- Nylobrade 020568- 86 Tube- Nylobrade 020565- 20 Tube- Nylobrade 053503 020565- 3 020565- 38 020565- 50 051729 038582 Fitting- 3/8MFL x 3/8 Barb Hose- Beverage Tube- Nylobrade Hose- Beverage Regulator- Water 30 PSI Fixed Tee- 3/8 Barb x 1/4MFL x 3/8 Barb 019194 029834 053503 020565- 16 Adaptor- SWV 3/8F X 3/8arb*SS* Ferrule- .650 ID NP Brass Fitting- 3/8MFL X 3/8Barb- Brass Hose- Beverage- 3/8 ID X 5/8 OD X53645 029834 Ferrule Line A.- Water *349*REG. 019194 Adaptor- Swivel- 3/8F x 3/8 Barb X53386 029834 Ferrule Line A.- Water- Regulator 019194 Adaptor X42219 029834 Ferrule Line A.- Water (Pump Inlet) 019194 Adaptor X44953 029834 Ferrule Line A.- Water (Pump Inlet) 049464 Elbow X49465 029834 Ferrule Line A.- Water (Pump Discharge) 049464 Elbow X49485 051826- 30 Line A.- Water (Pump Discharge) 051826- 28 Hose- Beverage PART NUMBER Hose- Beverage DESCRIPTION 1 1 1 1 1 1 6 1 1 1 2 2 1 1 2 2 1 2 2 1 2 1 345 QTY. 1 1 1 1 1 1 6 1 1 1 2 2 1 1 2 2 1 2 2 1 2 1 346 QTY. 1 1 6 1 1 1 2 2 1 1 2 2 1 349 355 QTY. QTY. 000 103 000 103 103 103 103 000 000 000 103 000 103 103 000 000 103 103 000 000 103 103 000 000 103 103 000 000 103 103 000 103 103 000 000 WARR. CLASS Bulk R30333 J9114233/Up Bulk R30333 Bulk R30333 Bulk R30333 345- J9067375/Up, 346- J9067641/Up Prior to J9102424 Prior to: 345- J9067375, 346- J9055262 Bulk - R30333 REMARKS 144 144 PARTS UPDATE + Available Separately Parts List 60 Models 345, 346, 349 & 355 051835- 4 051835- 3 051835- 2 051835- 1 Regulator- 60 PSI Regulator- 20 PSI Coil- Service- CO2 Manifold + Kit- Service- Valve & Coil 051835- 4 051835- 3 Regulator- 60 PSI Regulator- 20 PSI 051835- 2 027875 Coil- Service- CO2 Manifold Gauge- 60PSI- 1/8 MPT- Back Mount 051833- 27 X51832- 27 Manifold A.- CO2 - 1 Regulator - 2 Solenoid Manifold- CO2- 1 Regulator - 2 Solenoids 051839- 27 Manifold- CO2- 2 Regulator - 4 Solenoid 005139 044534 Valve- Check- 1/4MPT In X 1/4MFL Out Elbow- 1/4MFL X 1/8MPT Brass 044534 Valve- Check 1/4MPTINX1/4MFLOUT 051835- 1 052699 Gauge- 100 PSI- Back Mount + Kit- Service- Valve & Coil 027875 Gauge- 60 PSI- Back Mount 051839- 27 Manifold- CO2- 2Reg/4Sol*349* 051835- 2 001485 Fitting- 1/4MFL X 1/8MPT Coil- Service- CO2 Manifold 005139 X51838- 27 Elbow- 1/4MFL X 1/8MPT Brass Manifold A.- CO2 - 2 Regulator- 4 Solenoid 044534 052699 Gauge- 100 PSI - 1/8 MPT- Back Mount Valve- Check - 1/4MPT In X 1/4MFL Out 027875 051835- 27 Manifold- CO2 - 2 Regulator - 2 Solenoid Gauge- 60 PSI - 1/8 MPT- Back Mount 005139 Elbow- 1/4MFL X 1/8MPT Brass X51834- 27 038582 Tee- 3/8 BARBX1/4MFLX3/8BARB- SS Manifold A.- CO2 - 2 Regulators - 2 Solenoids 051729 Regulator- Water- 30 PSI Fixed 048232 020565- 8 Lubricant- Taylor 020565- 38 Hose- Beverage- 3/8 ID X 5/8 OD PART NUMBER Hose- Beverage- 3/8 ID X 5/8 OD DESCRIPTION 2 2 2 1 1 1 1 1 3 1 1 345 QTY. 2 2 2 1 1 1 1 1 3 1 1 346 QTY. 1 4 4 4 1 1 1 1 4 1 1 2 1 1 1 1 1 1 1 2 1 2 1 1 349 355 QTY. QTY. 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 000 103 103 000 000 WARR. CLASS J8040000/Up Includes: Plunger Tube, Nut, Coil & Bracket, Spring, Plunger & O- Ring J8054096/Up (Repl X47223- 27 Sol) Includes: Plunger Tube, Nut, Coil & Bracket, Spring, Plunger & O- Ring J8040000/Up Bulk R30333 Bulk R30333 REMARKS 136 136 129 136 136 136 129 136 136 136 136 128 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 61 Parts List 042352 018595 Valve- Check Washer- Flare Nylon 016309043666 013163 044949 Nut- Stud Pail (10 qt. - 9.5 liter) Pan- Drip (Expansion Valve) 019624 +Capacitor- Run - 4UF- 370V Motor- Pump 047060 +Blade- Fan (12” Push) 041401- 051785 Motor- Fan - 120 Watt 047279 +Capacitor- Run - 4UF- 440V 051744- 049009 +Blade- Fan (12” Push) Motor- Fan - 80 Watt +Blade- Fan (12” Push) 029770- 019624 +Capacitor- Run - 4UF- 370V Motor- Fan - 50 Watt 047061 041401- 53419 +Blade- Fan (12” Pull) Motor- Fan - 120 Watt +Blade- Fan (12” Pull) 029770- X42342 Manifold A.- Soda Motor- Fan 50 Watt 051826- 26 Hose- Beverage 033140- 051826- 23 Hose- Beverage Motor- Beater 051826- 19 Hose- Beverage 014477- 049427 Fitting- 3/8 O- Ring x 1/4 Barb SS Motor- Beater 052140 Ferrule 039710- M 020130 Adaptor- 1/8 MP x 1/4 Barb Man- Oper 345/346/349/355 016715 X49718 Adaptor- Swivel Manifold A.- Soda w/Check Valve 044534 051835- 1 Valve- Check - 1/4MPT In X 1/4MFL Out 051835- 3 Regulator- 20 PSI PART NUMBER + Kit- Service- Valve & Coil DESCRIPTION 1 1 8 1 1 1 1 1 1 2 1 345 QTY. 1 1 8 1 2 1 346 QTY. 1 16 1 2 1 4 4 1 2 2 1 4 10 1 5 1 1 8 1 1 1 1 1 1 1 1 1 1 2 2 1 349 355 QTY. QTY. 103 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 212 212 000 000 103 103 000 000 000 103 000 103 103 103 103 103 103 WARR. CLASS Prior to J8010000 Fan Motor (208- 230/60/1) J8010000 thru J9053837 J9053838/Up J9053838/Up Fan Motor - Prior to J9067375 Prior to J9067375 Prior to J9067375 J9067375/Up J9067375/Up Includes: Plunger Tube, Nut, Coil & Bracket, Spring, Plunger & O- Ring REMARKS 142 142 144 144 144 144 144 136 136 PARTS UPDATE + Available Separately Parts List 62 Models 345, 346, 349 & 355 043599 042082- BLA 042082- WHT 043599SBLA Panel- Front Lower Panel- Front- Lower Panel- Front Lower Panel- Front Lower X45136 X44917 X42289 044619- SP X53611 X44919 Panel A.- Left Side Panel A.- Left Side Panel- Left Side Panel A.- Side *346*AC*R*Filter Panel A.- Right Side 044916 Panel- Service Panel A.- Left Side 044621- SS Panel- Rear 042293 X42197 Panel A.- Rear Panel- Service 042198 Panel- Rear *349*Drain Hole* 053652 044921- SP1 Panel- Rear Panel- Service *349*AC* 042081- WHT Panel- Front Upper 045125 042081- BLA Panel- Front Upper Panel- Service 043600 Panel- Front Upper 053612 043600- BLA Panel- Front Upper Panel- Service *346* Filter 043599- SP Panel- Front Lower 049775 043599- BLA Panel- Front Lower +Plug- Hole- 1/2- Black X50226 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 020944- 11 Tube- Vinyl Drain Pan A.- Drip (Expansion Valve) 1 1 1 020944- 11 Tube- Vinyl Drain 1 1 X42204 X42202 Pan A.- Left Drip 1 1 1 1 1 1 1 2 1 1 1 349 355 QTY. QTY. X42203 X42201 Pan A.- Drip w/Hose (Left) 1 1 346 QTY. Pan A.- Right Drip 043612 345 QTY. Pan A.- Drip w/Hose (Right) 035034 Pan- Rear White Drip PART NUMBER Pan- Long Black Drip 19- 1/2 in Long DESCRIPTION 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 000 103 103 103 103 103 103 000 103 103 000 103 103 103 103 WARR. CLASS Water cooled and A/C prior to J9072433 Air cooled only - J9072433/Up Water cooled and A/C Prior to J9114233 Air cooled only J9114233/Up Water cooled and A/C prior to J9072433 Air cooled only - J9072433/Up Prior to J9114240 J9114240/Up Prior to J8110000 J8110000/Up Prior To J8060000 J8060000/Up, 355J9024482/Up Prior to J8060000 J8060000/UP Prior to J8110000 J8110000/Up Prior to J8060000 J8060000/Up Rear Shell Bearing Rear Shell Beariing Rear Shell Bearing Rear Shell Bearing Drip Guide Rear Shell Bearing REMARKS 130 130 130 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 63 Parts List X47299- SER X53580- SER PCB A.- Brown Out PCB A.- Control *345* UVC2 (CURRENT) X40875 X40876 Chip- Software UVC2 U10 English Chip- Software UVC2 U11 X40875 X40876 Chip- Software UVC2 U10 English Chip- Software UVC2 U11 040176- 006 X45315- SER PCB A.- Control (OLD STYLE) X40876 Chip- Software UVC2 U11 IC- Parallel Port Chip X40875 Chip- Software UVC2 U10 English X40791 X40873 Chip- Software UVC2 Chip- SEL Chip- Software X40872 X51169- SER Chip- Software UVC2 Display PCB A.- Universal (Base Board) X53653- SER X40838 PCB A.- Control (CURRENT) X44863- SER Chip- Software X47233- SER PCB A.- Universal (Base Board) PCB A.- Control (OLD STYLE) X40789 X40873 Chip- Software UVC2 Chip- SEL Chip- Software X40872 X51169- SER PCB A.- Universal (Base Board) Chip- Software UVC2 Display X53517- SER X40837 Chip- Software/Old PCB A.- Control *346*UVC2 (CURRENT) X44863- SER PCB A.- Universal (Base Board/Old) X47235- SER X40878 Chip- Software (Old) PCB A.- Control (OLD STYLE) X51169- SER X52440- SER PCB A.- UVC2 (Base Board) PCB A.- Control *345* UVC2 (OLD STYLE) X40790 X40873 Chip- Software UVC2 Chip- SEL Chip- Software X40872 Chip- Software UVC2 Display X51169- SER 044620- SP PCB A.- UVCA (Base Board) X42291 Panel- Right Side PART NUMBER Panel A.- Right Side DESCRIPTION 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 345 QTY. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 346 QTY. 1 1 1 1 1 1 1 1 1 1 1 1 1 349 355 QTY. QTY. 212 103 103 103 103 103 103 212 212 103 212 212 103 103 103 103 103 212 212 103 212 212 103 212 212 103 103 103 103 103 212 212 103 103 103 WARR. CLASS Use X53653- SER J9114233/Up J9114233/Up J9114233/Up Prior to J9067641 Prior to J9067641 Use X53517- SER J9067641/Up J9067641/Up J9067641/Up Prior to J8072717 Prior to J8072717 Use X52440- SER J8072717 thru J9067374 J8072717/UP J8072717 thru J9067374 J9067375/Up J9067375/Up REMARKS 148 148 148 148 145 145 145 145 145 145 132 132 132 132 132 132/144 144 PARTS UPDATE + Available Separately Parts List 64 Models 345, 346, 349 & 355 X40781 X44115 Plate A.- Decorative 038061- BLK 025570 035955 047094 047095 027616 042190 016306 Probe- Thermistor (Barrel) Pulley- 11” Dia. (Rear Bearing Unit) Pulley- 11” Dia. Pulley (Rear Bearing Unit) Pulley (Rear Bearing Unit) Pulley (Beater Motor) Pulley (Beater Motor) Pump- Water +O- Ring 1 1 1 2 2 2 4 X44115- BLA Plate A.- Decorative 1 029751 043639- BLA Plate- Dec- 345- 346- 355*BLACK 2 035410 Plate- Decorative (Cover w/Slots for Flavor Cards) 1 039568 035410- BLA Plate- Decorative Plug- Prime X45622- SER X40839 Chip- Software PCB A.- Interface X44863- SER PCB A.- Universal (Base Board) X47234- SER X40877 Chip- Software PCB A.- Control (OLD STYLE) X51169- SER PCB A.- UVC2 (Base Board) X52439- SER 1 X40876 Chip- Software UVC2 U11 Chip- Software- 355- 355A UVC2 PCB A.- Control *355*UVC2 (OLD STYLE) 1 X40875 Chip- Software UVC2 U10 English 1 X40873 1 X40872 Chip- Software UVC2 Chip- SEL X51169- SER 345 QTY. Chip- Software UVC2 Display PCB A.- UVC2 (Base Board) X52846- SER X40833 PCB A.- Control *355- 355A UVC2*(CURRENT) X44863- SER Chip- Software PART NUMBER PCB A.- Universal (Base Board) DESCRIPTION 1 2 2 2 4 2 1 1 1 1 1 1 1 1 346 QTY. 2 2 2 2 4 8 4 1 1 2 1 1 1 1 1 1 1 1 1 1 2 4 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 349 355 QTY. QTY. 103 103 103 103 103 103 103 103 000 103 103 103 103 103 103 212 103 212 212 103 212 212 103 103 103 103 103 212 212 103 212 WARR. CLASS Prior to J8060000 346- J9113331, 355- J9024482 J8060000 to: 345- J9125292, 345- J9125292/Up, 346- J9113331/Up, 355- J9024482/Up Prior to J8110000 (White) J8110000/Up Prior to J8072560 Prior to J8072560 Use X52439- SER J8072560 thru J9053837 J8072560/Up (Replaces X47234- SER) Use Prior to J9053838 J9053838/Up J8072560/Up J9053838/Up Prior to J9114233 Prior to J9114233 REMARKS 130 132 132 132 132/142 132 132/142 142 142 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 65 Parts List 051840 X53756 X44905 X53812 X43624 043719 Shell A.- Insulated (OLD) Shell A.- Insulated (NEW) Shell A.- Insulated (OLD) Shield- Splash 020945- 96 X38355 Shell A.- Insulated (NEW) +Tube- Vinyl Shelf A.- Drip Tray 020945- 96 X44898 Shelf A.- Drip Tray +Tube- Vinyl 044403 049697 +Screw- Thumb Shelf- Drip Tray 032560 039337 Shaft- Beater Drive +Seal X47221- 4 Sensor A.- Viscosity No. 4 025307 X47221- 3 Sensor A.- Viscosity No. 3 +O- Ring X47221- 2 Sensor A.- Viscosity No. 2 042278 X47221- 1 Sensor A.- Viscosity No. 1 +Bushing- Drive Shaft Seal X44951 051840- 22R Ring- Quad- Hose- Regulator- CO2 Sensor A.- EVC 051840- 22 Hose- Regulator- 3 Foot- Hi Pressure 041082 051840- 16 Gauge- Regulator- 3000 lb. 012725- 051840- 15 Gauge- Regulator- 160 lb. Sanitizer- Kay 5 051840- 7 Seat Assembly Relay- Compressor 051840- 6 Diaphragm Includes: 042791 Regulator- CO2 (Wall Mount) PART NUMBER Pump- Water DESCRIPTION 1 2 2 1 1 2 2 2 2 2 1 1 1 1 1 2 1 1 1 345 QTY. 1 2 2 1 1 2 2 2 2 2 1 2 1 1 1 2 1 1 1 346 QTY. 4 4 1 1 4 4 4 4 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 2 2 2 1 2 2 2 2 2 1 1 1 1 1 2 1 1 1 349 355 QTY. QTY. 103 512 512 512 512 000 103 000 103 000 103 000 000 103 103 103 103 103 103 103 000 103 000 103 103 103 000 103 103 103 WARR. CLASS Shell, X53880 CO2 Line & 053875- 5 or - 8 Feed Tube Prior to K0038353 Replace With X53812 3.5 Quart Mix Tank k0038353/Up Prior to Above Serial Numbers - replace with X53756 Shell, 053875- 5 or - 8 Feed tube. 345 & 346 also use X53880 CO2 Line. 345- K0026349/Up, 346- K0024873/Up, 349- K0025070/Up Includes Fittings Replaces 031623 REMARKS 151 151 124, 126 PARTS UPDATE + Available Separately Parts List 66 Models 345, 346, 349 & 355 043720 053875- 5 039566- 5 020945- 96 044455 047016 043232 053565 046365 050900 027137 047053 Tray- Front Drip Tube- Mix Feed (NEW) Tube- Mix Feed (OLD) Tube- Vinyl (Drip Tray Shelf- Drain Line) Valve- Access (Compressor) Valve- Access (Compressor) Valve- Access (Compressor) Valve- Access- 1/4MFL X 3/8ODSDR Valve- Automatic Expansion +Boot- Expansion Valve +Boot- Expansion Valve Valve- Check (Defrost Line) X44936 Switch A.- Float- Mix Level 038275- SP 038065 Switch- Membrane 043720- SP 053138 Switch- Membrane - 23” - Right Tray- Front Drip 044521 Switch- Membrane - 20” - Left Tray- Front Drip 036070 Switch- Low Pressure Switch (CO2) 045754 016292 Switch- Low Pressure Switch (H2O) Transformer 046362 Switch- Pressure - 440 PSI 012626 048230 Switch- Pressure - 440 PSI Switch- Toggle- SPST 3/4 HP 250V 036265 020445 +Washer- Freezer Stud 038276 Stud- Nose Cone (Freezing Cylinder) PART NUMBER Shield- Splash DESCRIPTION 2 2 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 1 1 1 8 8 345 QTY. 2 2 2 2 2 1 2 2 1 1 1 2 2 1 1 1 1 2 2 8 8 346 QTY. 4 4 4 4 4 2 2 4 4 1 1 1 4 4 1 1 2 2 16 16 1 2 2 2 2 1 1 2 2 1 1 1 2 2 1 1 1 1 1 1 8 8 349 355 QTY. QTY. 103 000 000 103 103 103 103 103 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 000 103 103 WARR. CLASS Prior to: 345- J906737, 349- J9102431 349- J9114233, 355- J9012316 Prior to: 345- J9067375, 346- J9072433, 349- J9114233/Up, 345- J9012316/Up 345- J9067375/Up, 346- J9072433/Up, 349- J9114233/Up 349- Prior to J9114233 Main High Side 349- Prior to J9114233 Use w/old style 2.5 quart mix tank New style 3.5 quart mix tank Power Mix Hopper 355- J9053838 Prior to: 345- J9067375, 346- J9072433, 345- J9067375/Up, 346J9072433, 355 - J9053838/Up 345- J9067375/Up, 346- 9072433/Up, 355 - J9053838/Up Prior to: 345- J9067375, 346- J9072433, 349- J9097086, 355- J9053838 349- J9097086/Up, 355- J9053838/Up 345- J9067375/Up, 346- J9072433/Up, REMARKS 144 151 151 144 142/144 142/144 144 142/144 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 67 Parts List 018520 018521 018522 018523 043638 044534 017444 +Marker- No. 1 +Marker- No. 2 +Marker- No. 3 +Marker- No. 4 +Regulator- CO2 (Primary) 0- 100 PSI +Valve- Check +Valve- Solenoid X34866 001486 021162 021029 018520 018521 043638 +Elbow A.- Restrictor +Elbow- Union +Restrictor- Air +Gauge- Pressure +Marker- No. 1 +Marker- No. 2 +Regulator (0- 100 PSI) X45309- X44508 Valve A.- Solenoid (Regulator/CO2) 043643 047496- +Valve- Solenoid +Manifold A.- CO2 030386 +Valve- Check +Gauge- Pressure (0- 100 PSI) 043638 +Regulator (0- 100 PSI) 021029 018521 +Marker- No. 2 +Gauge- Pressure (0- 60 PSI) 018520 +Marker- No. 1 X47223- 043643 +Gauge- Pressure (0- 100 PSI) Valve A.- Solenoid (Regulator/CO2) 021029 +Gauge- Pressure (0- 60 PSI) +Restrictor- Air 1 2 2 2 2 1 1 1 1 2 X44937- Valve A.- Solenoid (Regulator/CO2) 021162 053051- Valve- Solenoid 1/8 ORF X 1/4S 1 2 044982- Valve- Solenoid (Defrost) 2 345 QTY. X34866 053511- Valve- Sol 1/8ORF 1/4INX3/8OUT (Defrost) +Elbow A.- Restrictor 043449- PART NUMBER Valve- Solenoid (Liquid Line/Defrost) DESCRIPTION 2 2 2 1 1 1 1 2 2 1 2 2 346 QTY. 4 4 2 1 1 1 1 1 1 1 1 2 4 4 1 1 1 1 2 2 2 1 1 4 349 355 QTY. QTY. 103 000 000 103 000 103 103 103 103 103 103 000 000 000 000 103 103 103 103 103 103 103 000 000 103 103 000 103 103 103 103 103 WARR. CLASS Prior to S/N J8040000 Prior to S/N J8054096 - See Manifold Prior to S/N J8040000 J9055971/Up Prior to J9053838, 355 - 1 Used Prior to J9053838 346- J9072433/Up, 349- J9114233/Up J9053838/Up, 355 - 2 Used Prior to J9053838 355 - Prior to J9053838 REMARKS 129 129 128 144 142 142 PARTS UPDATE + Available Separately Parts List 68 Models 345, 346, 349 & 355 043643 044108 044110 044650 017450 016309- 12 044805 016306 029830 Gauge- Pressure (0- 100 PSI) Label- Warn- Press (Low Water Pressure) Label- Water Regulator Leg- Rubber (Rubber Bumper) Light- Indicator Motor- Pump Panel- Exterior Pump- Water Regulator (0- 50 PSI) 045166 028182 012906 038143 029439 048134 Belt Belt Capacitor- Run Capacitor- Start Capacitor- Run Capacitor- Start 50 CYCLE 077124 044558 Filter- Water Line Washer- 3/8 Flare- Nylon 053697 Filter- Water 1/4FFLINX1/4MFLOV 020565- 14 029834 Ferrule Tube- Nylobrade (Pump to Carbonator Tank) 007096 Elbow- 3/8 MFL x 3/8 MPT 016292 049464 Switch- Low Pressure (H2O) 036408 Elbow- 3/8 FFL x 3/8 Barb 050258- 12 Kit A.- Probe & Float Cord- Power 050257- 12 Probe A.- Carbonator w/Reed Switch Carbonator 049455- 12 018595 Washer- Nylon Flare REMOTE DISPENSER ASSEMBLY 046914- V 047496- Video- Train Film- FCB Pressure 030386 +Valve- Solenoid PART NUMBER +Valve- Check DESCRIPTION 1 1 1 1 18 1 345 QTY. 2 2 2 2 19 1 346 QTY. 2 5 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 2 1 2 1 1 1 1 19 1 2 2 349 355 QTY. QTY. 103 103 103 103 000 000 000 000 103 103 103 103 103 103 103 000 000 103 000 000 000 103 103 103 103 103 103 000 000 103 103 WARR. CLASS TECUMSEH TECUMSEH & COPELAND BRISTOL BRISTOL Bulk R30333 Replaces 044734 115 Volt - Prior to J7062208 115 Volt - J7062208/Up 346- J9072433/Up, 355- J9012316 345- J9055921/Up, 346- J9072433/Up, REMARKS 146, 147 119 PARTS UPDATE + Available Separately Models 345, 346, 349 & 355 69 Parts List 044422 038146 048133 051957- 12 051957- 40 Pulley (Beater Motor) Relay- Start Relay- Start Relay- Start- Compressor Relay- Start 1 X45116012796- Blower Assembly 022505 012768- Guard- Blower Motor- Fan 044833- SP 048231 046431 046686 Panel- Left Side Switch- Pressure - 350 PSI Switch- Pressure - 350 PSI Valve- Water 016289 048287 Condenser +Blade- Fan (7” Push) 047540 Condenser- WC- Coax Blower 1 012796- 1 1 1 1 1 1 1 053377 Blower- 100 CFM 1 1 1 1 1 1 1 1 1 2 2 2 1 2 1 1 2 2 2 2 2 2 2 2 1 2 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 345 346 349 355 QTY. QTY. QTY. QTY. Accumulator- Copper 2”DIA 13”LG WATER COOLED 037297 019624 Pulley (Beater Motor) +Capacitor- Run - 4UF/370V 047178- 34 Motor- Fan 100 Watt 047279 029770- 27 Motor- Fan 50 Watt +Blade- Fan (12”Push) 051960 Capacitor- Start 047061 012901 +Blade- Fan (12”Pull) 023606 Capacitor- Start- 145- 175UF/220V PART NUMBER Capacitor- Run DESCRIPTION 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 WARR. CLASS 345- J9053838/Up, 346- J9071890/Up, 349- J9114879/Up, 355- J9072849 Repl 018278 (J8050000/Up) 345- J9071890/Up, 349- J9114879/Up 345- J9071890/Up 2/18/99/Up COPELAND - J9053838/Up COPELAND TECUMSEH BRISTOL Fan Motor BRISTOL COPELAND - J9053838/Up COPELAND - J9053838/Up COPELAND COPELAND - J9053838/Up REMARKS 142 129 142 142 142 PARTS UPDATE BLK RIBBON CABLE SEE NOTE 2 12 10 2 4 6 8 J4 J6 J3 J5 W1 J2 RIBBON CABLE SEE NOTE 2 RIBBON CABLE SEE NOTE 2 1 2 J1 11 9 1 3 5 7 J7 CONTROL PCB A. J9 BARREL 1 BLK YEL BARREL 2 BLK BLK BLK BRN BARREL 1 SYRUP OUT SWITCH PROXIMITY SWITCHES BLK RED BRN BRN BLK C NO BARREL 1 BIB SWITCH BLK BRN BLK BLK BLU BLU BARREL 1 HOPPER FILL SWITCH SEE NOTE 2 RIBBON CABLE BRN SEE NOTE 2 RIBBON CABLE COMPRESSOR CONTACTOR T1 1 4 BLK C02 PRESSURE SWITCH BLK BLK 4 3 2 1 J5 1 2 3 4 1 2 3 4 5 6 7 8 J7 5 BLK BARREL 2 LIQ. LINE SOLENOID 3 1 J3 1 2 3 4 5 6 7 8 BLK RED/BLK J12 WHT BLK BLK T2 INTERFACE PCB A. W1 JUMPER BLOCK DETAIL L2 BRN COMPRESSOR CONTACTOR BRN BLK PRP PRP/WHT X1 J14 NO WHT/BLK C BARREL 2 BIB SWITCH BLK A RED 1 2 J1 RED/BLK J13 B BARREL 2 H20 SOL. WHT WHT WHT 7 6 5 4 3 21 WHT WHT L2 W1 J2 BARREL 2 SYRUP OUT SWITCH COMPRESSOR FIG.2 M ORG/WHT 7 6 5 4 3 21 ORN WHT/BLK STRIPE L1 RED/WHT PRP/WHT INTERFACE PCB A. J16 7 6 5 4 3 21 J4 J15 W2 7 6 5 4 3 21 J11 WHT ORG/WHT 6 5 4 3 21 WHT ORN 4 3 2 1 L1 BLK RED J6 WHT BLU/WHT BARREL 1 CO2 SOL. WHT RED/WHT 1 WHT BRN BLK YEL WHT/BLK WHT/BLK WHT L1 LINE L2 BLK PRIMARY LOAD L2 WHT SECONDARY CONT. TRANS. L1 EMI FILTER IN BLK BLK BRN OUT PCB A. OUT CONTROL SWITCH SPST RED/BLK YEL ORN ORN 2. STRIPED WIRE ON RIBBON CABLES MUST BE CONNECTED TO PIN 1 AT EACH END. WHT GROUND FRAME SECURELY OUT IN BLK WHT WHT WHT CARBONATOR FILL SWITCH WHT RIGHT BEATER MOTOR FIG.1 LEFT BEATER MOTOR FIG.1 RUN CAPACITOR USED WITH 041401-27 OR 047178-34 MOTOR ONLY. NOTE: 1. STATIC ELECTRICITY MAY CAUSE DAMAGE TO SOLID STATE COMPONENTS. ELIMINATE STATIC ELECTRICITY BY TOUCHING GROUNDED UNIT BEFORE HANDLING SOLID STATE COMPONENTS. 4 H2O PRESSURE SWITCH RED M FAN BARREL 1 LED BLK/WHT BARREL 2 LED BARREL 2 DEFROST SOLENOID WHT BARREL 2 CO2 SOL. BLK BRN BLU BARREL 2 HOPPER FILL SWITCH WHT WHT RED/WHT WHT BRN WHT BARREL 2 SYR.SOL. BLK BARREL 1 SYR.SOL. BRN EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04). EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED EMPTY SERVICE/TEST ONLY EMPTY EMPTY HPCO BARREL 1 BARREL 2 SEE NOTE 2 RIBBON CABLE RED/WHITE BLK YEL BLK YEL WHT PRP/WHT BLK JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH. BLK J11 J10 BARREL 2 KEYPAD RED BARREL 1 KEYPAD BLK J10 J9 J8 BRN BLK ORG/WHT 1 2 3 4 BARREL 1 H20 SOL. WHT/BLK COMP. CONT. COIL WHT/BLK BARREL 1 LIQ. LINE SOLENOID PRP BARREL 1 DEFROST SOLENOID BLK/YEL YEL BLK BRN BLU LCD DISPLAY BLK BLK PUMP M L2 BLK BLK 15A FUSE RED WHT RED LINE 6 5 1 WHT WHT/BLK T4 OR YEL A 2 1 BLU 4 5 1 2 RELAY WHT BLK BRN R S FIG.2 052396-1 RUN CAPACITOR WHT YEL WHT/BLK BLEED RESISTOR BRN C WHT LEESON 4 2 WHT/BLK 4 COPELAND COMPRESSOR WIRING START CAPACITOR EQUIPMENT GROUND FIG.1 INTERNAL OVERLOAD WHT(120 VOLTS) BLK(230 VOLTS) BLK YEL 1 BRN BEATER MOTOR WIRING MAGNATEK-CENTURY YEL P2 OR BRN 3 5 P1 OR PUR T8 OR RED 2 1 T5 OR BLK THERMAL OL T1 OR BLU GE/RBC BEATER MOTOR WIRING CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5 START THERMISTORS PROBES WHT/BLK WHT/BLK WHT WHT WHT WHT WHT BRN MAIN BLK PRP/WHT 12 2 L1 WHT/BLK WHT/BLK 1 11 345 053515-27 11/12/13 L2 BARREL 2 SYR.SOL. BRN BARREL 2 DEFROST SOLENOID M FAN WHT CONTROL SWITCH SPST BARREL 1 LED YEL L2 ORN ORN WHT LEFT BEATER MOTOR BLK RUN CAPACITOR USED WITH 041401-27 OR 047178-34 MOTOR ONLY. YEL LINE IN OUT WHT LOAD L2 PRIMARY SECONDARY CONT. TRANS. L1 EMI FILTER L1 RED/BLK STR BLK BLK IN BRN OUT PCB A. OUT WHT WHT/BLK RIGHT BEATER MOTOR WHT BLK WHT WHT WHT CARBONATOR FILL SWITCH BLK M PUMP L2 L3 BLK BARREL 2 CO2 SOL. RED/WHT WHT BLK BLK/WHT BARREL 2 LED RED 4 H2O PRESSURE SWITCH 1 WHT/BLK BLK BLK BLK BLK WHT B BRN BLU BARREL 2 HOPPER FILL SWITCH WHT BRN WHT BARREL 2 H20 SOL. X1 J13 A J14 7 6 5 4 3 21 RED/BLK 1 2 J1 PRP/WHT BLK PRP BLK NO BARREL 2 BIB SWITCH C WHT/BLK BLK BLK BLK BLK 15A FUSE BARREL 2 LIQ. LINE SOLENOID 2 J12 W1 7 6 5 4 3 21 BLK J2 12 BARREL 1 CO2 SOL. L1 WHT BLK/WHT BLK RED/BLK J3 1 2 3 4 5 6 7 8 RED BRN L3 L2 BLK BARREL 1 SYR.SOL. 1 1 BARREL 1 H20 SOL. WHT ORG/WHT 3 J4 BARREL 2 SYRUP OUT SWITCH BRN WHT WHT COMPRESSOR CONTACTOR T2 COMPRESSOR CONTACTOR T3 11 COMP. CONT. COIL WHT ORN J16 7 6 5 4 3 21 BLK BLK BLK WHT WHT BLK BARREL 1 LIQ. LINE SOLENOID WHT J15 7 6 5 4 3 21 RED/WHT INTERFACE PCB A. J11 W2 1 2 3 4 J5 1 2 3 4 5 6 7 8 J7 4 3 2 1 4 3 2 1 5 6 5 4 3 21 BLU/WHT J6 BLK BLK PRP/WHT THERMISTORS PROBES BARREL 1 DEFROST SOLENOID PRP/WHT WHT RED/WHT BLK YEL BLK YEL SEE NOTE 2 SEE NOTE 2 BLU BLU RED BLK C02 PRESSURE SWITCH 4 ORN ORG/WHT BRN LCD DISPLAY BARREL 2 KEYPAD SEE NOTE 2 J9 RIBBON CABLE RIBBON CABLE BLK BLK BARREL 1 HOPPER FILL SWITCH 1 M COMPRESSOR NOTE: 1. STATIC ELECTRICITY MAY CAUSE DAMAGE TO SOLID STATE COMPONENTS. ELIMINATE STATIC ELECTRICITY BY TOUCHING GROUNDED UNIT BEFORE HANDLING SOLID STATE COMPONENTS. WHT/BLK WHT/BLK ORG/WHT 1 2 3 4 WHT BLK 2. STRIPED WIRE ON RIBBON CABLES MUST BE CONNECTED TO PIN 1 AT EACH END. WHT/BLK WHT/BLK SEE NOTE 2 BRN BRN BLK BRN NO BLK BLU SEE NOTE 2 CONTROL PCB A. J7 C BARREL 1 BIB SWITCH BLK RIBBON CABLE BRN T1 RED J1 1 2 RED BLK PROXIMITY SWITCHES BARREL 1 SYRUP OUT SWITCH SERVICE/TEST ONLY RED WHT BRN BARREL 1 BLK INTERFACE PCB A. W1 JUMPER BLOCK DETAIL PRP/WHT BRN BLK RIBBON CABLE JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH. PRP WHT WHT WHT WHT WHT WHT/BLK BARREL 2 BARREL 1 HPCO BRN BLK L1 BLK COMPRESSOR CONTACTOR WHT/BLK YEL EMPTY EMPTY EMPTY - (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04). EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED EMPTY BLK/YEL J10 J9 J8 J11 J10 BARREL 2 BLK BLK BLK J4 J6 J3 J5 J2 W1 1 3 5 7 9 RED RIBBON CABLE 11 BLK BARREL 1 KEYPAD SEE NOTE 2 10 2 4 6 8 RIBBON CABLE 12 BLK YEL BLK BRN L1 BLK YEL 6 1 WHT WHT/BLK 5 GROUND FRAME SECURELY YEL 4 1 WHT WHT/BLK 2 LEESON COMPRESSOR WIRING BEATER MOTOR WIRING MAGNATEK-CENTURY COMPRESSOR TERMINALS LINE 345 053515-33 11/12/13 L2 BARREL 2 SYR.SOL. WHT BRN WHT RED/WHT WHT BARREL 2 DEFROST SOLENOID M FAN WHT BARREL 1 LED BLK/WHT BRN YEL BLK BLK L2 BLK LINE LOAD L2 PRIMARY WHT SECONDARY CONT. TRANS. L1 EMI FILTER L1 OUT IN ORN ORN GRN/YEL WHT GRN/YEL BLK WHT WHT WHT GRN/YEL GRN/YEL GRN/YEL BLK GRN/YEL CARBONATOR FILL SWITCH WHT RIGHT BEATER MOTOR FIG.1 LEFT BEATER MOTOR FIG.1 RUN CAPACITOR USED WITH 041401-27 OR 047178-34 MOTOR ONLY. YEL RED/BLK CONTROL SWITCH SPST IN BRN OUT PCB A. OUT WHT M PUMP GRN/YEL GRN/YEL N WHT WHT BARREL 2 CO2 SOL. RED BARREL 2 LED BLK BRN BLU BARREL 2 HOPPER FILL SWITCH WHT/BLK WHT/BLK GRN/YEL WHT GROUND FRAME SECURELY NOTE: 1. STATIC ELECTRICITY MAY CAUSE DAMAGE TO SOLID STATE COMPONENTS. ELIMINATE STATIC ELECTRICITY BY TOUCHING GROUNDED UNIT BEFORE HANDLING SOLID STATE COMPONENTS. 4 H2O PRESSURE SWITCH 1 WHT 345 053515-40 11/12/13 3 1 5 1 P1 OR PUR P2 OR BRN 2 BRN A BLK 4 2 R S WHT LEESON 1 WHT/BLK 4 WHT/BLK 1 2 YEL 5 T4 OR YEL T8 OR RED 2 THERMAL OL T5 OR BLK T1 OR BLU 6 WHT FIG.1 5 1 RELAY 4 BLU YEL WHT/BLK WHT 052396-1 RUN CAPACITOR BLEED RESISTOR BRN INTERNAL OVERLOAD WHT(120 VOLTS) BLK(230 VOLTS) WHT C BLK EQUIPMENT GROUND FIG.2 COPELAND COMPRESSOR WIRING START CAPACITOR BRN BEATER MOTOR WIRING MAGNATEK-CENTURY YEL MAIN GE/RBC BEATER MOTOR WIRING CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5 LINE START BLK B WHT BARREL 2 H20 SOL. BLK PRP PRP/WHT X1 J13 A BLK J14 7 6 5 4 3 21 1 2 J1 RED/BLK J2 RED NO BARREL 2 BIB SWITCH C WHT/BLK GRN/YEL WHT RED/WHT 15A FUSE BARREL 2 LIQ. LINE SOLENOID J12 W1 7 6 5 4 3 21 BLK 2 L1 WHT BLK/WHT BLK RED/BLK J3 1 2 3 4 5 6 7 8 12 BARREL 1 CO2 SOL. 1 BARREL 2 SYRUP OUT SWITCH BRN L2 COMPRESSOR CONTACTOR T2 WHT WHT WHT BARREL 1 SYR.SOL. WHT ORG/WHT 3 J4 ORG/WHT BRN 1 BARREL 1 H20 SOL. WHT ORN J16 7 6 5 4 3 21 BLK WHT WHT WHT BLK COMP. CONT. COIL WHT J15 7 6 5 4 3 21 RED/WHT PRP/WHT INTERFACE PCB A. J11 W2 1 2 3 4 J5 1 2 3 4 5 6 7 8 J7 4 3 2 1 4 3 2 1 5 6 5 4 3 21 BLU/WHT J6 BLK BRN THERMISTORS PROBES BARREL 1 LIQ. LINE SOLENOID BLU BLU BLK RED BLK M ORN LCD DISPLAY BARREL 1 DEFROST SOLENOID PRP/WHT WHT SEE NOTE 2 RED/WHT BLK YEL BLK YEL RIBBON CABLE SEE NOTE 2 BLK BLK SEE NOTE 2 BRN BRN BLK BARREL 1 HOPPER FILL SWITCH 4 C02 PRESSURE SWITCH 1 BLK BLK 2. STRIPED WIRE ON RIBBON CABLES MUST BE CONNECTED TO PIN 1 AT EACH END. WHT/BLK WHT/BLK RIBBON CABLE RIBBON CABLE BLK BRN BLK BARREL 1 BIB SWITCH NO T1 WHT/BLK WHT/BLK 11 RIBBON CABLE ORG/WHT 1 2 3 4 BARREL 2 KEYPAD BLK RED BRN C L1 COMPRESSOR CONTACTOR BLU SEE NOTE 2 J9 PROXIMITY SWITCHES BARREL 1 SYRUP OUT SWITCH BRN BLK SERVICE/TEST ONLY RED RIBBON CABLE J7 BARREL 2 BARREL 1 HPCO BLK RED BARREL 1 BLK INTERFACE PCB A. W1 JUMPER BLOCK DETAIL PRP/WHT WHT BRN YEL JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH. PRP BRN BLK J11 J10 WHT WHT WHT WHT WHT WHT/BLK COMPRESSOR FIG.2 WHT/BLK J10 J9 J8 RIBBON CABLE CONTROL PCB A. 1 EMPTY EMPTY BLK/YEL J1 1 2 W1 3 5 7 9 BLK J4 J6 J3 J5 J2 BARREL 2 BLK EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04). EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED EMPTY RED SEE NOTE 2 11 BLK BARREL 1 KEYPAD 4 6 8 10 2 SEE NOTE 2 12 BLK YEL BLK BRN L1 BLK 15 A FUSE J12 7 6 5 4 3 21 L2 W1 2 L1 BLK T2 A BLK J14 BARREL 2 SYR.SOL. C WHT WHT NO BARREL 2 BIB SWITCH BARREL 2 CO2 SOL. COMP. CONT. COIL BARREL 2 4 BLK YEL L1 WHT BLK L2 WHT BLK BRN S R 052396-1 WHT BLK WHT WHT BLK BLK RUN CAPACITOR BLEED RESISTOR BRN C INTERNAL OVERLOAD 2 RELAY 5 1 FIG.2 BLK CARBONATOR FILL SWITCH WHT RIGHT BEATER MOTOR FIG.1 WHT LEFT BEATER MOTOR FIG.1 YEL COPELAND COMPERSSOR WIRING - CSR BLU 4 WHT(120 VOLTS; 220V-50Hz) BLK(230 VOLTS) L2 START CAPACITOR EQUIPMENT GROUND BLK LINE LOAD L2 PRIMARY IN T2 RIGHT COMPRESSOR CONTRACTOR OUT BLK WHT SECONDARY CONT. TRANS. WHT ORN ORN EMI FILTER M WHT/BLK WHT/BLK OUT IN BLK BLK L1 LINE DEFROST SOLENOID BARREL 2 BLK RED/BLK CONTROL SWITCH SPST 1 T1 RIGHT COMPRESSOR FIG.2 BRN OUT PCB A. BARREL 1 LED L1 H2O PRESSURE SWITCH WHT/BLK BARREL 2 HOPPER FILL SWITCH RED BARREL 2 LED BLK PRP/WHT PRP BLU WHT BRN WHT RED/WHT BLK B BARREL 2 H20 SOL. BRN WHT/BLK BRN BLK RED X1 J13 7 6 5 4 3 21 J1 RED/BLK 1 2 L2 BARREL 2 SYRUP OUT SWITCH J2 12 7 6 5 4 3 21 BLK RED/BLK RED J3 1 2 3 4 5 6 7 8 RIGHT HPCO BLK 1 BARREL 1 CO2 SOL. 7 6 5 4 3 21 ORG/WHT WHT BARREL 1 SYR.SOL. RUN CAPACITOR USED WITH 046536-27 MOTOR ONLY BARREL 1 H20 SOL. 6 5 4 3 21 J4 3 1 INTERFACE PCB A. WHT BLK/WHT J16 5 J15 W2 1 2 3 4 J5 1 2 3 4 5 6 7 8 J7 4 3 2 1 4 3 2 1 RED BLK BLK BLK C02 PRESSURE SWITCH 4 M 11 BLK M BARREL 1 COMP. CONT. COIL BLU J11 ORN WHT BLU/WHT BLK J6 SEE NOTE 2 BLK BLU BARREL 1 HOPPER FILL SWITCH 1 BLK ORG/WHT L1 THERMISTORS PROBES BARREL 1 DEFROST SOLENOID RIBBON CABLE RIBBON CABLE BRN RIBBON CABLE SEE NOTE 2 BRN BLK BLK BRN NO BLK SEE NOTE 2 BLK WHT RED/WHT BLK YEL BLK YEL BLOWER BRN BARREL 1 BIB SWITCH C T1 WHT WHT LCD DISPLAY BARREL 2 KEYPAD J9 J7 CONTROL PCB A. J1 1 2 BRN RED BLK PROXIMITY SWITCHES BARREL 1 SYRUP OUT SWITCH BLK BRN L1 LEFT COMPRESSOR CONTACTOR BLK RIGHT COMPRESSOR CONTRACTOR ELIMINATE STATIC ELECTRICITY BY TOUCHING DAMAGE TO SOLID STATE COMPONENTS. 1. STATIC ELECTRICITY MAY CAUSE NOTE: WHT GROUNDING UNIT BEFORE HANDLING SOLID M PUMP L2 346 053566-27 11/12/13 1 5 P1 OR PUR 1 BRN A 4 2 WHT YEL WHT/BLK GE/RBC BEATER MOTOR WIRING CWLE-RED OR T8 INTERNAL ON #5, BLACK OR T5 INTERNAL ON #A} 3 P2 OR BRN WHT LEESON 1 WHT/BLK 4 WHT/BLK 1 2 YEL 5 T4 OR YEL T8 OR RED 2 THERMAL OL T5 OR BLK T1 OR BLU 6 WHT FIG.1 BEATER MOTOR WIRING MAGNATEK-CENTURY YEL MAIN BLU/WHT STATE COMPONENTS. START RIBBON CABLE BLK BLK BLK ORN ORG/WHT BRN GROUND FRAME SECURELY WHT MUST BE CONNECTED TO PIN 1 AT EACH END. WHT/BLK WHT/BLK BRN 2. STRIPED WIRE ON RIBBON CABLES WHT/BLK BRN EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04). EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED EMPTY SERVICE/TEST ONLY BLU BARREL 1 INTERFACE PCB A. W1 JUMPER BLOCK DETAIL RED WHT PRP/WHT BLK RED SEE NOTE 2 JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH. PRP BRN LEFT COMPRESSOR FIG.2 BLK BARREL 2 BARREL 1 LEFT HPCO BLK LEFT COMPRESSOR CONTACTOR BLK BRN 1 2 3 4 WHT WHT WHT WHT WHT WHT BLK WHT/BLK RIBBON CABLE EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04). EMPTY BLK BLK BLK BARREL 1 KEYPAD 3 5 1 4 6 7 9 W1 8 10 SEE NOTE 2 11 2 RIBBON CABLE 12 BLK/YEL WHT/BLK J10 J8 J9 RED BLK J11 J10 SEE NOTE 2 BLK J4 J6 J3 J5 J2 BARREL 2 YEL BLK YEL BLK BLK BRN BLK BLK SEE NOTE 2 M BLK BLK BLK BRN NO BLU BLU BARREL 1 CO2 SOL. L1 15 A FUSE J12 BLK L2 W1 7 6 5 4 3 21 BLK RED RED/BLK J3 1 2 3 4 5 6 7 8 BARREL 2 SYR.SOL. WHT BRN WHT RED/WHT WHT WHT BLU NO BARREL 2 CO2 SOL. BLK COMP. CONT. COIL BARREL 2 DEFROST SOLENOID BARREL 2 BLK RED/BLK CONTROL SWITCH SPST BRN OUT PCB A. BARREL 1 LED 1 4 H2O PRESSURE SWITCH BLK/WHT BARREL 2 LED RED BARREL 2 HOPPER FILL SWITCH L1 LINE L2 YEL WHT BLK BLK BLK BLK BLK CARBONATOR FILL SWITCH WHT RIGHT BEATER MOTOR L3 LEFT BEATER MOTOR WHT ORN ORN IN OUT WHT LOAD L2 PRIMARY SECONDARY CONT. TRANS. L1 EMI FILTER YEL BLK BLK IN OUT WHT T3 L2 RIGHT COMPRESSOR CONTRACTOR T2 WHT WHT BLK WHT BLK M PUMP L2 L3 BLK BLK B C BARREL 2 BIB SWITCH PRP PRP/WHT BLK BARREL 2 H20 SOL. X1 J13 A BLK BRN J14 7 6 5 4 3 21 1 2 J1 RED/BLK J2 RED BRN BARREL 2 SYRUP OUT SWITCH WHT/BLK WHT/BLK BLK BLK BLK BLK BARREL 1 SYR.SOL. WHT 1 RIGHT HPCO BLK WHT/BLK M BLK ORG/WHT J16 7 6 5 4 3 21 WHT ORN BARREL 1 H20 SOL. BLK J15 7 6 5 4 3 21 3 J4 INTERFACE PCB A. WHT BLK/WHT J11 W2 1 2 3 4 J5 1 2 3 4 5 6 7 8 J7 4 3 2 1 4 3 2 1 BLK BLK 4 5 6 5 4 3 21 BLU/WHT J6 BLK RED 1 C02 PRESSURE SWITCH L3 BLK BLK RIGHT COMPRESSOR CONTRACTOR BLK BLK RUN CAPACITOR USED WITH 046536-27 MOTOR ONLY BLK BARREL 1 HOPPER FILL SWITCH BLK T3 L2 LEFT COMPRESSOR CONTACTOR T2 T1 RIGHT COMPRESSOR BLK BLK BLK C BLK BLK WHT WHT THERMISTORS PROBES BARREL 1 DEFROST SOLENOID SEE NOTE 2 BARREL 1 COMP. CONT. COIL RIBBON CABLE SEE NOTE 2 BRN BRN BLK SEE NOTE 2 RIBBON CABLE RED/WHT BLK YEL BLK YEL WHT BLK BLOWER BRN BARREL 1 BIB SWITCH BLK M ORN ORG/WHT BRN LEFT COMPRESSOR CONTACTOR L1 WHT LCD DISPLAY J9 BRN RIBBON CABLE BRN T1 LEFT COMPRESSOR BLK BLU/WHT RIGHT COMPRESSOR CONTRACTOR WHT/BLK BARREL 2 KEYPAD RIBBON CABLE CONTROL PCB A. J7 RED BLK PROXIMITY SWITCHES BLK BRN BARREL 1 SYRUP OUT SWITCH BLK L1 LEFT COMPRESSOR CONTACTOR GROUND FRAME SECURELY WHT NOTE: 1. STATIC ELECTRICITY MAY CAUSE DAMAGE TO SOLID STATE COMPONENTS. ELIMINATE STATIC ELECTRICITY BY TOUCHING GROUNDED UNIT BEFORE HANDLING SOLID STATE COMPONENTS. WHT/BLK WHT/BLK BRN 2. STRIPED WIRE ON RIBBON CABLES MUST BE CONNECTED TO PIN 1 AT EACH END. BLU ORG/WHT 1 2 3 4 BARREL 1 BLK EMPTY EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04). EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED EMPTY SERVICE/TEST ONLY RED J1 1 2 BARREL 2 BARREL 1 LEFT HPCO YEL INTERFACE PCB A. W1 JUMPER BLOCK DETAIL RED BARREL 2 BLK BLK BLK WHT PRP/WHT WHT BRN SEE NOTE 2 EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04). BLK RIBBON CABLE JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH. PRP BRN BLK J10 J9 J8 WHT WHT WHT WHT WHT WHT/BLK 2 1 3 5 WHT/BLK 12 7 9 BLK/YEL 1 2 4 6 BLK 11 8 10 RED J11 J10 BARREL 1 KEYPAD SEE NOTE 2 W1 RIBBON CABLE 11 BLK J4 J6 J3 J5 J2 12 BLK YEL BLK BRN L1 BLK YEL 6 1 WHT WHT/BLK 5 YEL 4 1 WHT WHT/BLK 2 LEESON COPELAND COMPRESSOR WIRING BEATER MOTOR WIRING MAGNATEK-CENTURY COMPRESSOR TERMINALS LINE 346 053566-33 11/12/13 BLK RED M WHT BLOWER (FIG 3) BARREL 1 COMP. CONT. COIL BLU BARREL 1 H20 SOL. BARREL 1 SYR.SOL. ORG/WHT WHT BARREL 1 CO2 SOL. J16 7 6 5 4 3 21 ORN WHT BLU/WHT BLK J15 7 6 5 4 3 21 J4 3 1 L1 15 A FUSE RIGHT HPCO WHT J12 BLK BARREL 2 SYR.SOL. C WHT WHT NO BARREL 2 BIB SWITCH BARREL 2 CO2 SOL. DEFROST SOLENOID BARREL 2 BLK BLK 4 BLK L1 L1 L2 GRN/YEL LINE LOAD L2 PRIMARY IN YEL WHT L2 CAP BLK 60 HZ RED 50 HZ BRN WHT COM EXTRA MAIN 5 208/240 6 4 1 START 50/60 HZ THERMAL O.L. 2 2C MAIN FIG. 3 WHT GRN/YELL 3 WHT GRN/YEL WHT CARBONATOR FILL SWITCH BLK BLK GRN/YEL GRN/YEL WHT WHT GE BLOWER MOTOR SCHEMATIC BRN GRN/YEL WHT RIGHT BEATER MOTOR FIG.1 WHT LEFT BEATER MOTOR FIG.1 WHT T2 RIGHT COMPRESSOR CONTACTOR OUT WHT WHT SECONDARY CONT. TRANS. WHT WHT/BLK WHT/BLK M RIGHT COMPRESSOR FIG.2 ORN ORN EMI FILTER YEL COMP. CONT. COIL BARREL 2 WHT RED/BLK CONTROL SWITCH SPST 1 T1 OUT BROWN OUT IN PCB A. BARREL 1 LED L1 H2O PRESSURE SWITCH BLK/WHT BARREL 2 HOPPER FILL SWITCH RED BARREL 2 LED BLK PRP/WHT PRP BLU WHT BRN WHT RED/WHT BLK B BARREL 2 H20 SOL. BRN GRN/YEL WHT/BLK BRN BLK RED X1 J13 A J14 7 6 5 4 3 21 1 2 J1 RED/BLK J2 L2 BARREL 2 SYRUP OUT SWITCH T2 LEFT COMPRESSOR CONTACTOR BLK L2 W1 7 6 5 4 3 21 BLK 1 2 3 4 5 6 7 8 J3 RED/BLK RED INTERFACE PCB A. WHT BLK/WHT J11 5 6 5 4 3 21 W2 1 2 3 4 J5 1 2 3 4 5 6 7 8 J7 4 3 2 1 4 3 2 1 RED BLK BLK BLK C02 PRESSURE SWITCH 4 M 2 THERMISTORS PROBES BARREL 1 DEFROST SOLENOID BLK BLU SEE NOTE 2 J6 SEE NOTE 2 BLK WHT RED/WHT BLK YEL BLK YEL RIBBON CABLE RIBBON CABLE BRN BARREL 1 HOPPER FILL SWITCH 1 BLK WHT WHT LCD DISPLAY J9 J7 BLK BLK BRN NO BARREL 1 BIB SWITCH C T1 LEFT COMPRESSOR FIG.2 12 J1 BRN RIBBON CABLE SEE NOTE 2 BRN BLK RED BLK PROXIMITY SWITCHES BARREL 1 SYRUP OUT SWITCH BLK BRN L1 LEFT COMPRESSOR CONTACTOR BLK RIGHT COMPRESSOR CONTACTOR DAMAGE TO SOLID STATE COMPONENTS. ELIMINATE STATIC ELECTRICITY BY TOUCHING GROUNDING UNIT BEFORE HANDLING SOLID STATE COMPONENTS. M PUMP N 346 053566-40 11/12/13 YEL 3 1 5 1 P1 OR PUR P2 OR BRN BRN A 4 C BRN BLK 4 2 WHT WHT YEL WHT/BLK R RUN CAPACITOR 052396-1 BLEED RESISTOR BRN LEESON 1 WHT/BLK YEL WHT/BLK WHT 2 1 5 T4 OR YEL T8 OR RED 2 T5 OR BLK THERMAL OL T1 OR BLU 6 MAGNATEK-CENTURY FIG.1 BEATER MOTOR WIRING WHT INTERNAL OVERLOAD 2 RELAY 5 1 BLU 4 WHT(120 VOLTS; 220V-50Hz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a/356 052840-58 11/12/13 WHT RED 11 2 4 6 8 10 12 BLK JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH. BLK WHT BLK YEL BLK BRN L1 BLK GRN/YEL
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Print high-res Author : t165411 Create Date : 2013:11:22 15:43:19-06:00 Modify Date : 2014:05:22 08:58:22-05:00 Title : XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2014:05:22 08:58:22-05:00 Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Creator : t165411 Document ID : uuid:5ae05c44-0c6b-4c32-bd21-8d4a49e29858 Instance ID : uuid:71948d55-f6b7-4382-b6be-33b8961ba1ad Producer : Acrobat Distiller 10.1.1 (Windows) Page Count : 87EXIF Metadata provided by EXIF.tools