Taylor Gas Grill 811 Users Manual OpCvr
811 to the manual 58a23b64-28fc-4700-8b6a-e4e69c5b5b5d
2015-02-02
: Taylor Taylor-Taylor-Gas-Grill-811-Users-Manual-449432 taylor-taylor-gas-grill-811-users-manual-449432 taylor pdf
Open the PDF directly: View PDF 
.
Page Count: 95
| Download | |
| Open PDF In Browser | View PDF |
Model 811, 813, 819, 821 Series Auto Lift Gas Grills Original Operating Instructions 073625-M 9/15/10 (Original Publication) (Updated 4/19/13) Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on data plate: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: Amps Minimum Wire Ampacity: Amps Part Number: E September, 2010 Taylor All rights reserved. 073625-M The word Taylor and the Crown design are registered trademarks in the United States of America and certain other countries. Taylor Company 750 N. Blackhawk Blvd. Rockton, IL 61072 Table of Contents Section 1 To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Section 2 To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Section 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Section 4 Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 C811 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 L811 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 C813 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 L813 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 C819 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 L819 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 C821 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 L821 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Section 5 Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table of Contents 16 Model 811, 813, 819, 821 Series Table of Contents - Page 2 Section 6 Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Daily Opening Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Loading Store Menu Items To USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Loading Menu Items From USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Daily Cleaning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Section 7 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Section 8 Warranty Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Section 9 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Note: Continuing research results in steady improvements; therefore, information in this manual is subject to change without notice. Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be the original set of instructions. E September, 2010 Taylor (Original Publication) (Updated April, 2013) All rights reserved. 073625-M The word Taylor and the Crown design are registered trademarks in the United States of America and certain other countries. Model 811, 813, 819, 821 Series Taylor Company 750 N. Blackhawk Blvd. Rockton, IL 61072 Table of Contents Section 1 To the Installer The following are general installation instructions. For complete installation details, please see the checkout card. This unit has many sharp edges that can cause severe injuries. Installer Safety Site Preparation Review the area where the unit will be installed before uncrating the unit. Make sure all possible hazards to the user or equipment have been addressed. In all areas of the world, equipment should be installed in accordance with existing local codes. Please contact your local authorities if you have any questions. Care should be taken to ensure that all basic safety practices are followed during the installation and servicing activities related to the installation and service of Taylor equipment. S S S S Electrical Connections The grill is supplied with one power cord. Check the data plate on the grill for voltage, cycle, phase and electrical specifications. Only Taylor authorized service personnel should perform installation and repairs on the equipment. Authorized service personnel should consult OSHA Standard 29CFRI910.147 or the applicable code of the local area for the industry standards on lockout/tagout procedures before beginning any installation or repairs. Authorized service personnel must ensure that the proper PPE is available and worn when required during installation and service. Authorized service personnel must remove all metal jewelry, rings, and watches before working on electrical equipment. For proper power connections, refer to the wiring diagram provided inside the left side panel, attached to the gas manifold assembly. The power connection is located behind the access line cover on the front of the grill. In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70-1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered necessary for safety. Compliance therewith and proper maintenance will result in an installation essentially free from hazard! In all other areas of the world, equipment should be installed in accordance with the existing local codes. Please contact your local authorities. The main power supply(s) to the equipment must be disconnected prior to performing any repairs. Failure to follow this instruction may result in personal injury or death from electrical shock or hazardous moving parts as well as poor performance or damage to the equipment. The Proper Wire Size and Branch Circuit Overcurrent Device shall be selected according to the data label information and in accordance with CEC Part I 2006, Section 14-100(e)(i). FOLLOW YOUR LOCAL ELECTRICAL CODES! Note: All repairs must be performed by an authorized Taylor Service Technician. Model 811, 813, 819, 821 Series 1 To the Installer Installation CAUTION: THIS EQUIPMENT MUST BE PROPERLY GROUNDED! FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK! WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC 60417-1) on both the removable panel and the equipment's frame. This machine is designed for indoor use only. DO NOT install the machine in an area where a water jet could be used to clean or rinse the machine. Failure to follow this instruction may result in serious electrical shock. S S S Stationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation. This grill must be installed on a level surface. Failure to comply may result in personal injury or equipment damage. Installation of Cable Kit Appliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected or not used for long periods, or during initial installation, shall have protective devices such as a GFI, to protect against the leakage of current, installed by the authorized personnel to the local codes. If the unit is permanently connected, the Cable Kit must be installed. Flexible conduit must be used when installing the appliance. Ventilation and Clearance To ensure proper operation of this appliance, it must be installed so that the products of combustion are efficiently removed. Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion. After set up, do not store anything on top of the grill. Failure to follow this instruction may result in a fire hazard. Grease Disposal Container If the grill is not factory-equipped with grease disposal containers, the store is required to provide appropriate grease disposal containers in accordance with NSF Standard 4 requirements. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified person, in order to avoid a hazard. 130304 To the Installer 2 Model 811, 813, 819, 821 Series Section 2 To the Operator The Taylor grills included in this manual consist of the base model numbers 811, 813, 819, and 821. Prefix letters were added to the base model numbers to denote minor design differences: C = Standard Platen Length (17.5” / 445 mm) L = Longer Platen Length (21” / 533 mm) G = Grooved Option The models 811 and 813 are 36” (914 mm) grills. The 811 is equipped with three upper platens and the 813 is equipped with two upper platens. Note: Warranty is valid only if the parts are authorized Taylor parts, purchased from an authorized Taylor Distributor, and the required service work is provided by an authorized Taylor service technician. Taylor reserves the right to deny warranty claims on equipment or parts if non-approved parts or refrigerant were installed in the machine, system modifications were performed beyond factory recommendations, or it is determined that the failure was caused by neglect or abuse. The models 819 and 821 are 24” (610 mm) grills. The 819 is equipped with two upper platens and the model 821 is equipped with one upper platen. These grills are capable of cooking a variety of products and feature two cooking options. They provide all the features of a flat grill as well as the advantages of two-sided cooking. Note: Constant research results in steady improvements; therefore, information in this manual is subject to change without notice. If the crossed out wheeled bin symbol is affixed to this product, it signifies that this product is compliant with the EU Directive as well as other similar legislation in effect after August 13, 2005. Therefore, it must be collected separately after its use is completed, and cannot be disposed as unsorted municipal waste. The grill you have purchased has been carefully engineered and manufactured to provide dependable operation. When properly operated and maintained, it will produce a consistent quality product. Like all mechanical products, it will require cleaning and maintenance. A minimum amount of care and attention is necessary if the operating procedures in this manual are followed closely. This Operator's Manual should be read before operating or performing any maintenance on your equipment. It is strongly recommended that all personnel responsible for the equipment's operation and cleaning review these procedures for proper training and assurance that no misunderstandings exist. In the event you should require technical assistance, please contact your local authorized Taylor Distributor. The user is responsible for returning the product to the appropriate collection facility, as specified by your local code. For additional information regarding applicable local laws, please contact the municipal facility and/or local distributor. 120525 Model 811, 813, 819, 821 Series 3 To the Operator Section 3 Safety We, at Taylor Company, are concerned about the safety of the operator when he or she comes in contact with the grill and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to protect both you and the service technician. As an example, warning labels have been attached to the grill to further point out safety precautions to the operator. IMPORTANT - Failure to adhere to the following safety precautions may result in severe personal injury or death. Failure to comply with these warnings may damage the machine and its components. Component damage will result in part replacement expense and service repair expense. S DO NOT operate the grill unless all service panels and access doors are attached with screws. S All repairs must be performed by an authorized Taylor service technician. S The main power supplies to the grill must be disconnected prior to performing any repairs. S For Cord Connected Units: Only Taylor authorized service technicians or licensed electricians may install a plug or replacement cord on these units. S Stationary appliances which are not equipped with a power cord and a plug or other device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation. S Appliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected or not used for long periods, or during initial installation, shall have protective devices such as a GFI, to protect against the leakage of current, installed by the authorized personnel to the local codes. S Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomersheathed cord, (Code designation 60245 IEC 57), installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion. To Operate Safely: DO NOT operate the grill without reading this operator's manual. This manual should be kept in a safe place for future reference. This appliance is to be used only by trained personnel. It is not intended for use by children or people with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Failure to follow the instructions below may result in severe injury or death from electrocution: S S DO NOT operate the grill unless it is properly grounded. DO NOT operate the grill with larger fuses than specified on data label. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified person, in order to avoid a hazard. 130304 Safety 4 Model 811, 813, 819, 821 Series IMPORTANT: DO NOT use a water jet or spray excessive water on or anywhere near the grill. Failure to follow this instruction may result in serious electrical shock and cause permanent electrical and mechanical damage to internal parts. DO NOT use cold water or ice to cool the upper platen or the lower cook surface. Failure to follow this instruction may result in: Failure to follow this instruction may result in: S serious electrical shock S burns from hot steam S serious electrical shock S burns from hot steam S S liquid collecting inside the grill and destroying electrical components Take caution to protect eyes, lungs, and all parts of the body from potential harm when using any chemical cleaner. Failure to follow this instruction may result in a chemical burn. This appliance must be isolated from all combustible construction and materials including, but not limited to; walls, partitions, furniture, floors, curtains, paper, boxes, and decorations. Failure to comply may result in fire and cause destruction and severe injury. DO NOT use any abrasives or cleaners other than approved food service cleaners and degreasers. Failure to comply may cause illness to the consumer and may also damage grill surfaces. FOR YOUR SAFETY For thorough cleaning, the grill must be pulled away from the wall. Before moving the grill, remove the grease cans. Turn off the gas at the quick connect shut-off valve on the flexible hose. Disconnect the gas quick connector. Disconnect the tether to the grill, located on the back panel of the unit. To return the grill to its original position, reverse the steps. Use extreme caution to smoothly and slowly roll the grill backward into place. Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. USE EXTREME CAUTION while setting up, operating, and cleaning the grill. S S S Failure to do so may cause the grill to tip and can result in severe equipment damage or personal injury. Avoid coming in contact with hot grill surfaces or with hot grease. DO NOT prepare or remove product without proper equipment. DO NOT allow untrained personnel to operate this grill. Cleaning and sanitizing schedules are governed by your state or local regulatory agencies and must be followed accordingly. Please refer to the cleaning section of this manual for the proper procedure to clean this unit. Failure to follow these instructions can result in burn injuries. Model 811, 813, 819, 821 Series liquid collecting inside the grill and destroying electrical components 5 Safety These instructions are valid only if the country code symbol appears on the appliance. If the symbol does not appear on the appliance, refer to the technical instructions which give the necessary instructions for adapting the appliance to the utilization conditions of that country. Access to the service area of the unit is restricted to persons having knowledge and practical experience with the appliance, in particular as far as safety and hygiene are concerned. S S DO NOT obstruct the ventilation openings at the rear of this appliance. DO NOT obstruct the flow of air in and around the grill. If the crossed out wheeled bin symbol is affixed to this product, it signifies that this product is compliant with the EU Directive as well as other similar legislation in effect after August 13, 2005. Therefore, it must be collected separately after its use is completed, and cannot be disposed as unsorted municipal waste. NOTICE all warning labels that have been attached to the grill to further point out safety precautions to the operator. This piece of equipment is made in America and has American sizes on hardware. All metric conversions are approximate and vary in size. The user is responsible for returning the product to the appropriate collection facility, as specified by your local code. NOISE LEVEL: Airborne noise emission does not exceed 70 dB(A) when measured at a distance of 1.0 meter from the surface of the machine and at a height of 1.6 meters from the floor. For additional information regarding applicable local laws, please contact the municipal facility and/or local distributor. 130304 Safety 6 Model 811, 813, 819, 821 Series Section 4 Operator Parts Identification C811 Exploded View Figure 1 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 CAN A.-GREASE X80925 12 NUT-JAM 1-1/2-12 (2 PCS) 073594 2 SLIDE-GREASE CAN LEFT 069936 13 CASTER-5" 7-5/8 STEM 078377 3 PANEL-SIDE-UPPER *LEFT 073990 14 CASTER-GRILL 5” SWIVEL LOC 073240 4 SCREW-10-32X3/8 SLTD TRUS 024298 15 KIT A.-GRILL CONTROL GEN X73474-SER 5 PANEL-SIDE-LOWER *LEFT 073992 16 SWITCH-ROCKER-DPST-10A 076989-WP KIT A.-GREASE SHIELD X78330-SER 17 BUTTON-OPERATOR-BLACK 076012 7 PANEL A.-BACK SERVICE X73993 18 BUTTON-OPERATOR-RED 076011 8 DEFLECTOR A.-FLUE X69555 19 COVER A.-USB WATERPROOF 068583 9 SCREW-3/8-16X34 SERR HWH 017328 20 PANEL A.-FRONT UPPER X69550 10 PANEL-SIDE-UPPER *RIGHT 073989 21 PANEL A.-FRONT-LOWER X73979 11 PANEL-SIDE-LOWER *RIGHT 073991 22 SLIDE-GREASE CAN RIGHT 069935 *6 *NOTE: 1 KIT PER PLATEN 121003 Model 811, 813, 819, 821 Series 7 Operator Parts Identification L811 Exploded View Figure 2 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 CAN A.-GREASE X80925 12 NUT-JAM 1-1/2-12 (2 PCS) 073594 2 SLIDE-GREASE CAN LEFT 069936 13 CASTER-5" 7-5/8 STEM 078377 3 PANEL-SIDE-UPPER *LEFT 073990 14 CASTER-GRILL 5” SWIVEL LOC 073240 4 SCREW-10-32X3/8 SLTD TRUS 024298 15 KIT A.-GRILL CONTROL GEN X73474-SER 5 PANEL-SIDE-LOWER *LEFT 073992 16 SWITCH-ROCKER-DPST-10A 076989-WP KIT A.-GREASE SHIELD X78330-SER 17 BUTTON-OPERATOR-BLACK 076012 7 PANEL A.-BACK SERVICE X73993 18 BUTTON-OPERATOR-RED 076011 8 DEFLECTOR A.-FLUE X69555 19 COVER A.-USB WATERPROOF 068583 9 SCREW-3/8-16X34 SERR HWH 017328 20 PANEL A.-FRONT-LOWER X73979 10 PANEL-SIDE-UPPER *RIGHT 073989 21 SLIDE-GREASE CAN RIGHT 069935 11 PANEL-SIDE-LOWER *RIGHT 073991 *6 *NOTE: 1 KIT PER PLATEN 120907 Operator Parts Identification 8 Model 811, 813, 819, 821 Series C813 Exploded View Figure 3 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 CAN A.-GREASE X80925 13 CASTER-5" 7-5/8 STEM 078377 2 SLIDE-GREASE CAN LEFT 069936 14 073240 3 PANEL-SIDE-UPPER *LEFT 073990 CASTER-GRILL 5" SWIVEL W/LOCK 4 SCREW-10-32X3/8 SLTD TRUS 024298 15 KIT A.-GRILL CONTROL GEN X73474-SER 5 PANEL-SIDE-LOWER-LEFT 073992 16 SWITCH-ROCKER-DPST-10A 076989-WP 17 BUTTON-OPERATOR-BLACK 076012 18 BUTTON-OPERATOR-RED 076011 19 COVER A.-USB WATERPROOF 068583 20 PANEL A.-FRONT UPPER X69550 21 PANEL A.-FRONT-LOWER X73979 22 SLIDE-GREASE CAN RIGHT 069935 *6 KIT A.-GREASE SHIELD X78330-SER 7 PANEL A.-BACK SERVICE X73993 8 DEFLECTOR A.-FLUE X69555 9 SCREW-3/8-16X3/4 SERRATED 017328 10 PANEL-SIDE-UPPER *RIGHT 073989 11 PANEL-SIDE-LOWER-RIGHT 073991 12 NUT-JAM 1 1/2-12 STEEL *NOTE: 1 KIT PER PLATEN 073594 121003 Model 811, 813, 819, 821 Series 9 Operator Parts Identification L813 Exploded View Figure 4 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 CAN A.-GREASE X80925 12 NUT-JAM 1 1/2-12 STEEL 073594 2 SLIDE-GREASE CAN LEFT 069936 13 CASTER-5" 7-5/8 STEM 078377 3 PANEL-SIDE-UPPER *LEFT 073990 14 SCREW-10-32X3/8 SLTD TRUS 024298 CASTER-GRILL 5" SWIVEL W/LOCK 073240 4 5 PANEL-SIDE-LOWER-LEFT 073992 15 KIT A.-GRILL CONTROL GEN X73474-SER 16 SWITCH-ROCKER-DPST-10A 076989-WP 17 BUTTON-OPERATOR-BLACK 076012 18 BUTTON-OPERATOR-RED 076011 19 COVER A.-USB WATERPROOF 068583 20 PANEL A.-FRONT-LOWER X73979 21 SLIDE-GREASE CAN RIGHT 069935 *6 KIT A.-GREASE SHIELD X78330-SER 7 PANEL A.-BACK SERVICE X73993 8 DEFLECTOR A.-FLUE X69555 9 SCREW-3/8-16X3/4 SERRATED 017328 10 PANEL-SIDE-UPPER *RIGHT 073989 11 PANEL-SIDE-LOWER-RIGHT 073991 *NOTE: 1 KIT PER PLATEN 120907 Operator Parts Identification 10 Model 811, 813, 819, 821 Series C819 Exploded View Figure 5 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 CAN A.-GREASE X80925 13 NUT-JAM 1 1/2-12 STEEL 073594 2 SLIDE-GREASE CAN LEFT 069936 14 CASTER-5" 7-5/8 STEM 078377 3 PANEL-SIDE UPPER-LEFT 073990 15 073240 4 SCREW-10-32X3/8 SLTD TRUS 024298 CASTER-GRILL 5" SWIVEL W/LOCK 5 PANEL-SIDE-LOWER-LEFT 073992 16 KIT A.-GRILL CONTROL X73474-SER 6 SLIDE-GREASE CAN RIGHT 069935 17 PANEL A.-FRONT-LOWER X69660 7 PANEL A.-BACK SERVICE X69664 18 SWITCH-ROCKER-DPST-10A 076989-WP 19 COVER A.-USB WATERPROOF 068583 20 BUTTON-OPERATOR-BLACK 076012 21 BUTTON-OPERATOR-RED 076011 22 PANEL A.-LIGHT X80626 8 DEFLECTOR A.-FLUE X69657 9 SCREW-3/8-16X1-1/2 SERR 020129 KIT A.-GREASE SHIELD X78330-SER *10 11 PANEL-SIDE UPPER-RIGHT 073989 12 PANEL-SIDE-LOWER-RIGHT 073991 *NOTE: 1 KIT PER PLATEN 121106 Model 811, 813, 819, 821 Series 11 Operator Parts Identification L819 Exploded View Figure 6 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 CAN A.-GREASE X80925 13 NUT-JAM 1 1/2-12 STEEL 073594 2 SLIDE-GREASE CAN LEFT 069936 14 CASTER-5" 7-5/8 STEM 078377 3 PANEL-SIDE UPPER-LEFT 073990 15 073240 4 SCREW-10-32X3/8 SLTD TRUS 024298 CASTER-GRILL 5" SWIVEL W/LOCK 5 PANEL-SIDE-LOWER-LEFT 073992 16 KIT A.-GRILL CONTROL X73474-SER 6 SLIDE-GREASE CAN RIGHT 069935 17 PANEL A.-FRONT-LOWER X69660 7 PANEL A.-BACK SERVICE X69664 18 SWITCH-ROCKER-DPST-10A 076989-WP 19 COVER A.-USB WATERPROOF 068583 20 BUTTON-OPERATOR-BLACK 076012 21 BUTTON-OPERATOR-RED 076011 22 PANEL A.-LIGHT X80626 8 DEFLECTOR A.-FLUE X69657 9 SCREW-3/8-16X1-1/2 SERR 020129 KIT A.-GREASE SHIELD X78330-SER *10 11 PANEL-SIDE UPPER-RIGHT 073989 12 PANEL-SIDE-LOWER-RIGHT 073991 *NOTE: 1 KIT PER PLATEN 130316 Operator Parts Identification 12 Model 811, 813, 819, 821 Series C821 Exploded View Figure 7 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 CAN A.-GREASE X80925 13 PANEL-SIDE-LOWER-RIGHT 073991 2 SLIDE-GREASE CAN LEFT 069936 14 NUT-JAM 1 1/2-12 STEEL 073594 3 PANEL-SIDE UPPER-LEFT 073990 15 CASTER-5" 7-5/8 STEM 078377 4 SCREW-10-32X3/8 SLTD TRUS 024298 16 073240 5 PANEL-SIDE-LOWER-LEFT 073992 CASTER-GRILL 5" SWIVEL W/LOCK 6 PANEL A.-LIGHT X80626 17 KIT A.-GRILL CONTROL X73474-SER 7 PANEL A.-BACK SERVICE X69664 18 PANEL A.-FRONT-LOWER X69660 19 SWITCH-ROCKER-DPST-10A 076989-WP 20 COVER A.-USB WATERPROOF 068583 21 BUTTON-OPERATOR-BLACK 076012 22 BUTTON-OPERATOR-RED 076011 8 DEFLECTOR A.-FLUE X69657 9 SCREW-3/8-16X1-1/2 SERR 020129 KIT A.-GREASE SHIELD X78330-SER *10 11 PANEL-SIDE UPPER-RIGHT 073989 12 SLIDE-GREASE CAN RIGHT 069935 *NOTE: 1 KIT PER PLATEN 121106 Model 811, 813, 819, 821 Series 13 Operator Parts Identification L821 Exploded View Figure 8 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 CAN A.-GREASE X80925 13 PANEL-SIDE-LOWER-RIGHT 073991 2 SLIDE-GREASE CAN LEFT 069936 14 NUT-JAM 1 1/2-12 STEEL 073594 3 PANEL-SIDE UPPER-LEFT 073990 15 CASTER-5" 7-5/8 STEM 078377 4 SCREW-10-32X3/8 SLTD TRUS 024298 16 073240 5 PANEL-SIDE-LOWER-LEFT 073992 CASTER-GRILL 5" SWIVEL W/LOCK 6 PANEL A.-LIGHT X80626 17 KIT A.-GRILL CONTROL X73474-SER 7 PANEL A.-BACK SERVICE X69664 18 PANEL A.-FRONT-LOWER X69660 19 SWITCH-ROCKER-DPST-10A 076989-WP 20 COVER A.-USB WATERPROOF 068583 21 BUTTON-OPERATOR-BLACK 076012 22 BUTTON-OPERATOR-RED 076011 8 DEFLECTOR A.-FLUE X69657 9 SCREW-3/8-16X1-1/2 SERR 020129 KIT A.-GREASE SHIELD X78330-SER *10 11 PANEL-SIDE UPPER-RIGHT 073989 12 SLIDE-GREASE CAN RIGHT 069935 *NOTE: 1 KIT PER PLATEN 130318 Operator Parts Identification 14 Model 811, 813, 819, 821 Series Accessories Figure 9 ITEM DESCRIPTION PART NO. 1 SHEET-RELEASE - BOX OF 9 (C811, C813, C819, C821) 073442 *2 RETAINER-SHEET RELEASE (RETENTION BAR) (C811, C813, C819, C821) 072845 **3 CLIP-RELEASE MATERIAL W/TAB 072673 4 SCRAPER-TEFLON WIPER 075887 5 STRIP-REPLACEMENT 075888 ITEM DESCRIPTION PART NO. ***6 HOLDER-CLEANING 073736 ***7 PAD-CLEANING 073737 CLEANER-STERA SHEEN (CASE OF 6, 1 QT. BOTTLES) 073160 *9 RETAINER-SHEET RELEASE (RETENTION BAR) (L811, L813, L819, L821) 080594 10 SHEET-RELEASE -BOX OF 9 (L811, L813, L819, L821) 080595 8 * SHOWN PER PLATEN ** SHOWN PER PLATEN (NOTE: EXTRA CLIPS ARE SENT WITH GRILL) *** SOLD SEPARATELY THROUGH YOUR LOCAL DISTRIBUTOR 120720 Model 811, 813, 819, 821 Series 15 Operator Parts Identification Section 5 Important: To the Operator Note: The Model 811 three platen grill has been selected for illustration purposes. Figure 10 ITEM DESCRIPTION ITEM DESCRIPTION 1 RAISE BUTTON 6 PROGRAM KEY 2 STANDBY/COOK MODE BUTTON 7 TEMPERATURE INDICATOR LIGHTS 3 USB COVER/CONNECTION 8 POWER KEY 4 POWER SWITCH 9 FUNCTION DISPLAY 5 CLEAN MODE KEY 10 MENU SELECT KEYS 120604 Important: To the Operator 16 Model 811, 813, 819, 821 Series Section 6 Operating Procedures The three platen Model L811 has been selected to illustrate the step-by-step procedures. For grills equipped with less than three platens, perform the following steps as appropriate for your grill platen configuration. Step 2 Hook the release sheet retainer on the release sheet shoulder screws at the top of the upper platen. Daily Opening Procedures Before operating the grill, the release sheets must be installed on the upper platens. The release sheets are reversed and rotated on a daily basis (black side vs. gray side.) Perform the following steps for installing release sheets: Figure 12 Step 3 Hold the non-hemmed end of the release sheet. Gently pull the sheet tight, wrapping it around the platen in a side-to-side manner. CAUTION: Make sure the grill is COOL before attempting to install or remove release sheets. Step 1 Slide the release sheet retainer through the hemmed end of the release sheet. Figure 13 Note: Check the alignment of the release sheet and make sure it fits smoothly over the upper platen. Figure 11 130206 Model 811, 813, 819, 821 Series 17 Operating Procedures Step 4 Place the release sheet clips over the release sheet. Press them into place over the release sheet bar at the top of the platen. Step 6 Repeat steps 1 through 5 for the remaining upper platen(s). Note: Temperature checks should only be conducted with the release sheets removed. Replace the release sheet when: S Cleaning procedures fail to remove all buildup and product sticks to the release sheet. S A tear appears in the cooking area of the release sheet, causing product to stick to the release sheet. Figure 14 Step 5 Check the tightness of the release sheet against the upper platen. Figure 16 CAUTION: The upper platen surface and release sheet are very hot. To prevent burn injuries, wear heat-resistant gloves when replacing the release sheets. Figure 15 Note: Installing the release sheets too tightly may cause premature failure of the sheet. Note: It is not necessary to change the release sheet if small pin holes develop on the sheet. 130205 Operating Procedures 18 Model 811, 813, 819, 821 Series Care of Release Sheets IMPORTANT! Clean the release sheets using the grill cleaning pad and holder identified on page 15 ONLY. Using any other pad and holder will damage the release sheets. DO NOT: S DO NOT fold or crease. Figure 18 Note: Contact your local Taylor Distributor to purchase the correct grill cleaning pad and holder. (See page 15.) Figure 17 S DO NOT touch with sharp objects, grill scrapers, or abrasive pads. S DO NOT place under other equipment or objects. S DO rinse to remove cleaner and allow to dry on a flat surface. S DO rotate the release sheet daily and re-install on opposite side than previously used (black side vs. brown side). Start Up of the Grill S DO NOT hot-hose or soak in water. IMPORTANT! The lower grill surface and the upper platen MUST BE CLEAN before starting these procedures. Step 1 Place the power switch in the ON position. DO: S DO clean with a squeegee after each run of product. S DO wipe with a clean, sanitizer-soaked grill cloth a minimum of 4 times per hour and more often during peak periods. S DO clean daily on both sides, using an approved high temperature grill cleaner and the grill cleaning pad and holder identified on page 15. Figure 19 110602 Model 811, 813, 819, 821 Series 19 Operating Procedures Note: If an ignition failure fault occurs upon start up, press the center of the control. The control will display “OFF”. Refer to problem #2, items a, b, and c of the Gas Grill Troubleshooting Guide on page 42. After five minutes has elapsed, press the menu key again. If the ignition failure fault was not resolved, please call your authorized service technician. The control will display the word “INITIALIZATION” for five seconds and then will enter the OFF mode, displaying the message “OFF”. The temperature indicators will not be illuminated. A tone will sound for 20 seconds unless the operator touches the display screen, raise button or the standby button. Figure 20 Step 2 Touch a menu key on the control to start the grill. The grill will start heating up to the proper temperature. The control will display the selected menu item and indicate “BOTTOM TOO COOL” and “TOP TOO COOL”. The grill temperature indicators will be illuminated in amber. Figure 22 When the grill is at the proper temperature, the temperature statements will no longer display and the temperature indicators will be illuminated in green. Figure 21 Operating Procedures Figure 23 20 Model 811, 813, 819, 821 Series Step 3 The PROGRAM MODE screen will appear. Programming Menu Items To enter the Program Mode, the grill control must be in the OFF or IDLE mode. Step 1 Press and hold the PROGRAM key for approximately five seconds to enter the Program Mode. Figure 26 UNITS Key The UNITS key is used to select either English or metric units of measure. The UNITS key toggles between F and C with each key press. Figure 24 ADJUST VOLUME Key Step 2 The PASSWORD screen will appear. Enter the Operator Password “STORE1” and press the OK key. The ADJUST VOLUME key displays the current volume. To increase or decrease the volume, use the UP and DOWN arrow keys. Figure 25 Model 811, 813, 819, 821 Series Figure 27 21 Operating Procedures To edit a menu item, press the menu item key to bring up a virtual keyboard. Type in the desired name (up to 8 characters per line) and then press the “X” key to return to the previous screen. MENU EDIT Key The MENU EDIT key is used to program a menu item. When the MENU EDIT key is pressed, the following screen will display. Figure 30 ACTIVE: YES or NO. This key displays the current selection. Pressing the key toggles to the opposite selection. Selecting YES will display the menu item on the main display screen. Figure 28 TOP TEMP: This key displays the current set point temperature for the platen. To increase or decrease the temperature, use the UP and DOWN arrow keys. If there is more than one screen of menu items, press the Previous or Next arrow keys to access the other menu items. BOTTOM TEMP: This key displays the current set point temperature for the lower grill surface. To increase or decrease the temperature, use the UP and DOWN arrow keys. Press the menu item key to be programmed. The following screen will display. Note: When setting the temperatures for a given item, the limits are 150°F to 450°F (66°C to 232°C) for the upper platen and 150°F to 400°F (66°C to 204°C) for the lower grill surface. If the temperatures are set lower or higher than the temperature limits, the set point at the control will default to 150°F and 450°F (66°C and 232°C) respectively. CLAM/FLAT: This key displays the current setting (CLAM or FLAT) associated with that function. Pressing the key toggles the mode to the opposite selection. GAP: This key is only active if CLAM has been selected. The key displays the platen gap (in inches or mm) associated with the FUNCTION. To increase or decrease the gap setting, use the UP and DOWN arrow keys. Figure 29 Operating Procedures 22 Model 811, 813, 819, 821 Series MULTIPLE TIMING FUNCTIONS: There is one timing function for clam items and a maximum of 3 timing functions for each flat menu item. Each function has a set of parameters associated with it. The function currently associated with the menu item is displayed. Pressing either function 1, function 2, or function 3 will bring up the next function in the list. The functions provided are: S S S VIEW HELP Key The View Help key is not functional at this time (future development). Loading Store Menu Items To USB The same USB flash drive that was used to load software into the grill can be used to perform this procedure. REMOVE IN TURN IN SEAR IN Step 1 Remove the USB cable cap from the USB connector to access the USB port. ALARM AUTO/MANUAL: This key displays the current status of the alarm mode. Pressing the key toggles the mode to the opposite selection. Note: Grills built prior to serial number M1035495 will require the front control panel be lowered to access the control display boards. If ALARM AUTO is selected, the alarm will automatically stop after five seconds has elapsed. Selecting ALARM MANUAL requires the operator touch anywhere on the display screen or the raise or standby buttons to stop the alarm. Step 2 Insert the USB flash drive into the USB port. Step 3 Press and hold the PROGRAM key for 5 seconds to enter the Program Mode. XXX SECONDS: This key displays the time associated with that menu item in seconds. To increase or decrease the seconds setting, use the UP and DOWN arrow keys. Upon completion of all programming selections, save the selections by pressing the OK key. To return to the main display screen without saving the programming selections, press the X key. SERVICE CONTACT INFORMATION Key Figure 32 Press the SERVICE CONTACT INFORMATION key to view the programmed service contact information. Step 4 Enter the Operator Password “STORE1” and press the OK key. Figure 31 Figure 33 110603 Model 811, 813, 819, 821 Series 23 Operating Procedures Step 5 Press the MENU EDIT key. Step 8 Remove the USB flash drive from the USB port and reinstall the USB cable cap on the USB connector. Note: Grills built prior to serial number M1035495 will require the front control panel be reinstalled. Loading Menu Items From USB Once the proper software is loaded on the USB flash drive, the next control board can be programmed from the USB flash drive. Figure 34 Step 1 Repeat Steps 1 through 5 from “Loading Store Menu Items to USB.” Step 6 Press the STORE MENU TO USB key. Step 2 Press the LOAD MENU FROM USB key. Step 3 The control can display up to 5 different menu options loaded on the USB flash drive. Select the key for the correct menu to load. The control will display “DONE” at the bottom of the screen when the menu is loaded. Step 4 Remove the USB flash drive from the USB port and reinstall the USB cable cap on the USB connector. Step 5 To load menu items from the USB flash drive to another control board, repeat these software loading procedures. Figure 35 Step 7 Enter a file name (up to 8 characters) to save the menu items, using the keyboard displayed on the control. Press the OK key. The menu items are saved to the USB flash drive. Note: Grills built prior to serial number M1035495 will require the front control panel be reinstalled. 110603 Operating Procedures 24 Model 811, 813, 819, 821 Series Patty Placement & Removal Placement procedures of meat products must be followed on the grill. The meat must be placed on the lower grill surface from front to back. When the cook cycle is complete, the upper platen will raise. Patties must be removed immediately after the upper platen has been raised to the OPEN position and after the meat has been seasoned. Patties are generally placed two at a time from front to back of grill and right to left. The removal order of the patties is shown in the diagrams by the number shown in the center of each patty. Note: It is very important that all patties be removed from the lower grill surface in the same sequence that they were placed before cooking. L Series Grills (Longer Platen Version) 130312 Model 811, 813, 819, 821 Series 25 Operating Procedures Patty Placement & Removal (continued) C Series Grills (Shorter Platen Version) 130312 Operating Procedures 26 Model 811, 813, 819, 821 Series During the cooking cycle, the display will show the name of the current menu item, “REMOVE IN”, and the time remaining until the product should be removed. Operating Procedures Cooking Product Step 1 Select the menu item to be cooked. The grill is at the correct temperature if the control does not display any temperature statements and the grill temperature indicators are green. Step 2 Quickly place the product on the lower grill surface, from front to back. Figure 37 At the end of the cook cycle, the control will display “DONE”, a tone will sound, and the platen will automatically raise. Step 3 Press the STANDBY button once. Figure 38 Figure 36 Note: To cancel a cook cycle at any time, press the RAISE button. A tone will sound and the display will read “CANCEL” for five seconds and then enter an IDLE mode. The display reads “MOVING DOWN” as the platen lowers to the cook surface. Model 811, 813, 819, 821 Series 27 Operating Procedures Standby Procedures Menu Parameters Whenever the grill is idle and product is not being cooked, the upper platen must be placed in the STANDBY position. To view the settings and actual temperatures for the current item, press and hold the menu item key a minimum of 5 seconds. The screen will display the cook time, gap setting, temperature set points and actual temperature readings for each zone for that menu item. Step 1 To place the upper platen in the STANDBY position, press the STANDBY button twice from the open position. Figure 41 Figure 39 If a key is not pressed for 20 seconds, the grill control will return to the normal display. Pushing the “X” key will bring the display back to the main display page. The control will display “GOING TO STANDBY” and then change to display “STANDBY”. Step 2 To raise the upper platen to the OPEN position to resume cooking, press the RAISE button. Cleaning After Each Run of Product Step 1 Using the grill scraper, scrape the grease on the lower grill surface from front to back. Do not scrape across the rear of the lower grill surface with the grill scraper. Figure 40 CAUTION: Never use force to raise the upper platen. Damage to components may result. Only use the RAISE button to open the upper platen! Operating Procedures Figure 42 28 Model 811, 813, 819, 821 Series Step 2 Use the wiper squeegee to clean the release sheet on the upper platen. Hold the handle at a slight upward angle. Use a downward motion to clean the sheet. (Note: Do not use excessive pressure when wiping the release sheet with the squeegee, as this can scratch or tear the release sheet.) Step 4 Use the grill cloth to clean the back splash plate and the bullnose areas as needed during operation. Note: To increase the life of the release sheet, wipe it with a clean, sanitizer-soaked, folded grill cloth a minimum of four times every hour. CAUTION: The upper platen surface is very HOT! To prevent burn injuries, use extreme caution when wiping the release sheet. Daily Cleaning Procedures Note: The three platen Model L811 has been selected to illustrate the step-by-step procedures. For grills equipped with less than three platens, perform the following steps as appropriate for your grill platen configuration. Step 1 Raise the upper platen to the OPEN position by pressing the red RAISE button. Figure 43 Step 3 Using the wiper squeegee, push the grease at the rear of the lower grill surface into the grease can. Do not use the grill scraper for this step. Figure 44 CAUTION: Never use force to raise the upper platen. Damage to components may result. Only use the RAISE button to open the upper platen! Note: DO NOT turn the power switch to the OFF position while the platens are in the “down” position. 120127 Model 811, 813, 819, 821 Series 29 Operating Procedures Step 2 Press the CLEAN key. When the cook surfaces reach the proper temperature for cleaning, an alarm will sound and the message “READY TO CLEAN” will be displayed. Step 4 Put on heat-resistant gloves. Figure 47 CAUTION: The upper platen surface and release sheets are very hot. To prevent burn injuries, use extreme care. Figure 45 Step 3 Press the RAISE button to cancel the alarm. Step 5 Wipe the exposed surface of the release sheets with a clean, sanitizer-soaked grill cloth. Figure 46 Figure 48 130205 Operating Procedures 30 Model 811, 813, 819, 821 Series Step 6 Remove the release sheet clip, release sheet retainer, and the release sheet. Take these parts to the sink to be washed and rinsed. Step 10 Scrape the lower grill surface with the grill scraper, from front to back. Figure 51 Step 11 Use the wiper squeegee to push residual grease into the grease cans. Figure 49 Step 7 Repeat steps 1 through 6 for the remaining upper platen(s). Step 8 Wash and rinse the clips and retainers in the sink. Set them aside for future use. Step 9 Set the release sheets aside on a clean, flat surface next to the sink until further cleaning is performed. DO NOT fold, crease, or place them on sharp objects. Figure 52 Step 12 Remove, empty, and reinstall the grease cans. Figure 50 Figure 53 120524 Model 811, 813, 819, 821 Series 31 Operating Procedures Step 13 Using an approved high temperature grill cleaner, pour approximately 3 oz. (90 ml) onto each 12” (305 mm) cook zone. Step 17 Apply grill cleaner to the bottom of the platen handles. Figure 54 Step 14 Firmly attach the non-abrasive pad to the grill cleaning pad holder. Figure 56 IMPORTANT! Use the grill cleaning pad and holder identified on page 15 ONLY. Using any other pad and holder will damage the release sheets. DO NOT use metal scrapers, abrasive pads, screens, or wire brushes. Damage to components may result. Step 15 Dip the pad into the grill cleaner. Step 18 Apply grill cleaner to the platen surfaces. IMPORTANT: DO NOT SCRUB while applying grill cleaner in the following steps: Step 16 Apply grill cleaner to the front side of the upper platens. Figure 55 Figure 57 130201 Operating Procedures 32 Model 811, 813, 819, 821 Series Step 19 Apply grill cleaner to the back side of the upper platens. Step 25 Lightly scrub the platen surfaces. Figure 59 Step 26 Lightly scrub the back side of the upper platens. Figure 58 Step 20 Apply grill cleaner to the outer edges of the right and left platens. Step 21 Press the STANDBY button twice to lower one of the platens. Figure 60 811 Only: Press the STANDBY button twice to lower the center platen. Apply grill cleaner to both sides of the center platen. Step 27 Lightly scrub the outer edges of the right and left platens. Step 28 Press the STANDBY button twice to lower one of the platens. Step 22 Apply grill cleaner to the inner edges of the right and left platens. 811 Only: Press the STANDBY button twice to lower the center platen. Lightly scrub both sides of the center platen. Step 23 Press the RAISE button to raise the lowered platen. Step 29 Lightly scrub the inner edges of the right and left platens. Step 24 Lightly scrub the front side of the platens and the bottom of the platen handles with the non-abrasive pad until all soil has been liquified by the grill cleaner. For stubborn soils, apply additional grill cleaner and lightly scrub. Do not rinse the platens at this time. Step 30 Press the RAISE button to raise the lowered platen. Step 31 With a clean, sanitizer-soaked grill cloth, rinse the front, sides, and back of the platen surfaces. 110610 Model 811, 813, 819, 821 Series 33 Operating Procedures Step 32 With a clean, sanitizer-soaked grill cloth, rinse the bottom of the platen handles, and the front, sides, and back of the platen surfaces. Step 34 Press the STANDBY button twice to lower one of the platens. 811 Only: Press the STANDBY button twice to lower the center platen. With a clean, sanitizer-soaked grill cloth, rinse both sides of the center platen. Step 35 With a clean, sanitizer-soaked grill cloth, rinse the inner edges of the right and left platens. Step 36 Press the RAISE button to raise the lowered platen. Step 37 With a clean, sanitizer-soaked grill cloth, wipe the exterior of all the platens, especially behind the rear of the upper platens (next to the arm assembly). Step 38 Starting at the back of the lower grill, spread the remaining grill cleaner over the entire surface. Do not scrub while applying product. Figure 61 Step 39 Lightly scrub the surface with the non-abrasive pad until all soil has been liquified by the grill cleaner. Step 33 With a clean, sanitizer-soaked grill cloth, rinse the platen cook surfaces. Figure 63 Note: The rear of the upper platen, as well as the tubular arm, can easily be wiped from the front of the unit. If cleaning is performed on a daily basis, there should be no carbon build-up. Figure 62 130201 Operating Procedures 34 Model 811, 813, 819, 821 Series IMPORTANT! To avoid damaging the grill: DO NOT use a jet of water to clean or rinse S the grill. S DO NOT use cold water or ice to cool the upper platen or the lower cook surface. S Failure to follow these instructions may result in: S serious electrical shock S burns from hot steam S S Never use grill screens on the upper platen or the lower grill surface. Never use any abrasives or cleaners other than the approved cleaner. Never allow the grill scraper or the abrasive cleaning materials to come in contact with the release sheet. Step 41 Pour a small amount of lukewarm water on a clean, sanitizer-soaked grill cloth, while holding it over the lower grill surface. Wipe the lower grill surface until all residue is removed. liquid collecting inside the grill and destroying electrical components damaged cook surfaces Step 40 Carefully pour warm water on the lower grill surface, starting from the back to the front. Use the squeegee to remove the cleaner from the grill surface. Figure 65 IMPORTANT! Step 42 must be performed using the grill cleaning pad and holder identified on page 15 ONLY. Using any other pad and holder will damage the release sheet. Note: Contact your local Taylor Distributor to purchase the correct grill cleaning pad and holder. (See page 15.) Figure 64 Model 811, 813, 819, 821 Series 35 Operating Procedures Step 42 Place the release sheets flat on the lower grill surface. Gently clean both sides of the sheets with an approved high temperature grill cleaner and the grill cleaning pad and holder. Step 46 Remove and empty the grease cans. Figure 68 Step 47 Wash, rinse, and reinstall the grease cans. Figure 66 Step 48 Wipe all areas with a clean, sanitizer-soaked grill cloth. Step 43 Rinse both sides of the release sheets with a clean, sanitizer-soaked grill cloth. Step 49 Wipe all exterior panels. 24 Hour Stores Only: Step 48 Re-install the release sheets on the opposite side than previously used. Secure the sheets with the release sheet clips and retainers. Start up the grill per instructions starting on page 17. Figure 67 Step 44 Place the release sheets on a clean, sanitized, flat surface to air dry overnight. Step 45 Wipe the lower grill surface with a clean, sanitizer-soaked grill cloth. Repeat until no visible soil remains. Figure 69 130107 Operating Procedures 36 Model 811, 813, 819, 821 Series Step 51 Leave the upper platens in the OPEN position overnight. Non-24 Hour Stores Only: Step 50 Apply a light coat of vegetable oil to the entire lower grill surface. Step 52 Place the power switch in the OFF position. Figure 70 Figure 71 120830 Model 811, 813, 819, 821 Series 37 Operating Procedures Section 7 PROBLEM 1. One side of the grill will not heat. The control will display the message, “PROBE FAULT”. 2. One heat zone will not heat. The display reads “TOO COOL”. 3. One of the heat zones is overheating. The display reads “TOO HOT”. 4. The grill will not turn on when power switch is placed in the ON position. 5. The upper platen will not stay in the STANDBY mode, but will stay in the COOK position. Troubleshooting Guide PROBABLE CAUSE REMEDY a. One power connection is not connected. a. Check the power connection. b. The restaurant circuit breaker has tripped. b. Reset the restaurant circuit breaker. c. The contactor is faulty. c. Call a service technician. d. The heater is faulty. d. Call a service technician. e. The high limit switch is faulty. e. Call a service technician. f. The solid state relay is faulty. f. Call a service technician. a. The interface board is faulty. a. Call a service technician. b. The solid state relay is faulty. b. Call a service technician. c. The control harness is faulty. c. Call a service technician. a. The interface board is faulty. a. Call a service technician. b. The solid state relay is faulty. b. Call a service technician. a. The restaurant circuit breaker has been tripped. a. Reset the circuit breaker. b. The control cord is not connected properly. b. Reconnect the cord. c. The fuse in the control box is faulty. c. Call a service technician. d. The power switch is faulty. d. Call a service technician. a. Incorrect use of the STANDBY button. a. Press STANDBY button within five seconds of lowering the platen into the COOK position. b. Faulty wire connections. b. Call a service technician. 120521 Troubleshooting Guide 38 Model 811, 813, 819, 821 Series PROBLEM 6. The upper platen will not stay in the COOK or STANDBY position. PROBABLE CAUSE REMEDY a. Temperature is insufficient to satisfy the indicator LED's. a. Wait until the indicator LED's turn green. b. The control harness is faulty. b. Call a service technician. c. The interface board is faulty. c. Call a service technician. d. The latch switch is faulty. d. Call a service technician. e. The latch solenoid is faulty. e. Call a service technician. f. The processor control is faulty. f. Call a service technician. g. The pneumatic system is faulty. g. Call a service technician. a. The product is out of specification. a. Product must be within specification (proper thickness, shape, etc.). b. The processor control is not set properly. b. Call a service technician. 8. The upper platen opens too rapidly. a. The orifice/check valve is incorrect or missing. a. Call a service technician. 9. The display reads “PLATEN NOT LATCHED”. a. The pneumatic system is faulty. a. Call a service technician. b. The latch switch is faulty. b. Call a service technician. c. The latch solenoid is faulty. c. Call a service technician. a. The arm bearings are dirty. a. Call a service technician. b. The air cylinder is faulty. b. Call a service technician. c. Plugged air lines to cylinders. c. Call a service technician. 7. The upper platen will not stay in the COOK position, but will stay in the STANDBY mode. 10. The display reads “UPPER PLATEN STUCK”. 120521 Model 811, 813, 819, 821 Series 39 Troubleshooting Guide PROBLEM 11. The platen will not lower to preset gap height. 12. The product is under-cooked or overcooked. PROBABLE CAUSE REMEDY a. Excessive carbon build-up on the shields. a. Follow closing procedures to properly clean and remove carbon build-up from the shields. b. Defective motor interface board. b. Call a service technician. c. Loose harness connections. c. Call a service technician. d. Defective main display controller. d. Call a service technician. e. Defective motors and cables. e. Call a service technician. a. The release sheet is worn. a. Replace the release sheet. b. Incorrect cooking time. b. Reset the processor control for the correct time. c. Incorrect temperature setting. c. Adjust the processor control to the proper setting. d. The upper platen or lower grill surface is not clean and/or has carbon build-up. d. Follow closing procedures to properly clean the upper platen and the lower grill surface and to remove carbon build-up. e. There is a grease or carbon build-up on the bottom of the upper platen handles. e. Follow closing procedures to properly clean and remove carbon build-up from the bottom of the platen handles. f. The preset gap height is incorrect. f. Call a service technician. g. The heating zone is not heating. g. Call a service technician. 130201 Troubleshooting Guide 40 Model 811, 813, 819, 821 Series PROBLEM PROBABLE CAUSE REMEDY a. The upper platen or lower grill surface is not clean and/or has carbon build-up. a. Follow closing procedures to properly clean the upper platen and the lower grill surface and to remove carbon build-up. b. There is a grease or carbon build-up on the bottom of the upper platen handles. b. Follow closing procedures to properly clean and remove carbon build-up from the bottom of the platen handles. c. The release sheet is worn. c. Replace release sheet. d. The product is out of specification. d. Product must be within specification (proper thickness, shape, etc.). e. The platen is not level. e. Call a service technician. f. The preset gap height is incorrect. f. Call a service technician. g. Air pressure is not high enough. g. Call a service technician. 14. The display reads “PROBE OPEN” and displays the specific zone. a. The thermocouple or the thermocouple interface board is faulty. a. Call a service technician. 15. The display reads “HOME SWITCH STUCK ON.” a. Two sided cooking options are blocked. a. Turn the control off and then back on to clear the fault. b. Defective stepper motor. b. Call a service technician. c. Defective stepper motor wire harness. c. Call a service technician. d. Defective home switch. d. Call a service technician. e. Defective motor control. e. Call a service technician. a. Defective motor control. a. Call a service technician. b. Defective stepper motor. b. Call a service technician. c. Defective stepper motor wire harness. c. Call a service technician. d. Defective home switch. d. Call a service technician. e. Broken platen cable. e. Call a service technician. 13. The product is not cooking evenly. 16. The display reads “HOME SWITCH NOT SEEN.” 130201 Model 811, 813, 819, 821 Series 41 Troubleshooting Guide GAS ZONES ONLY PROBLEM 1. The display reads “BLOWER FAILURE”. 2. The burner will not light. The display reads “IGNITION FAILURE”. 3. The burner lights but will not stay lit. 4. The burner lights but the zone is cool or overheats. Troubleshooting Guide PROBABLE CAUSE REMEDY a. The blower is faulty. a. Call a service technician. b. The pressure switch is faulty. b. Call a service technician. a. The quick disconnect gas hose is not fully engaged. a. Re-engage the quick disconnect. b. The manual shutoff valve is in the OFF position. b. Turn the valve to the ON position. c. Air is in the gas hose. c. Wait 5 minutes before relighting. d. The processor control is faulty. d. Call a service technician. e. The spark ignition module is faulty. e. Call a service technician. f. The gas solenoid is faulty. f. Call a service technician. g. The electrode is faulty. g. Call a service technician. h. The interface board is faulty. h. Call a service technician. a. The electrode is faulty. a. Call a service technician. b. Improper ground. b. Call a service technician. a. The grill is out of calibration. a. Call a service technician. b. The processor control is faulty. b. Call a service technician. c. The thermocouple is faulty. c. Call a service technician. 42 Model 811, 813, 819, 821 Series Section 8 Warranty Explanation Class 103 Parts Class 512 Parts The warranty for new equipment Class 512 parts is five years from the original date of unit installation, with a replacement parts warranty of twelve months. The warranty for new equipment Class 103 parts is one year from the original date of unit installation, with a replacement parts warranty of three months. Class 000 Parts Class 000 parts are considered wear items - no warranty. Class 212 Parts Class *** Parts The warranty for new equipment Class 212 parts is two years from the original date of unit installation, with a replacement parts warranty of twelve months. See warranty explanation on the back of the check-out card. CAUTION: Warranty is valid only if the parts are authorized Taylor parts, purchased from an authorized Taylor Distributor, and the required service work is provided by an authorized Taylor service technician. Taylor reserves the right to deny warranty claims on equipment or parts if non-approved parts or refrigerant were installed in the machine, system modifications were performed beyond factory recommendations, or it is determined that the failure was caused by neglect or abuse. 121003 Model 811, 813, 819, 821 Series 43 Warranty Explanation Parts List PART NUMBER X72954 X72843 BACKSPLASH A. BAR A.-RELEASE MATERIAL 44 078730 077042 080648 072541 080647 076013 073423 073033 051331 076451 X73975 X73023 073334 BEARING 3/4 ID-SELF ALIGN BEARING-FLANGE 3/4 X 15/16 BEARING-FLANGE 5/8 X 15/16 BEARING .753 X 1.000 X 2.000 BEARING .628 X .813 X 2.0 BLOCK-CONTACT 1 NO BLOCK-TERMINAL 1P BLOCK-TERMINAL 2P .25 SPD-24X BLOCK-TERMINAL 3P 20A, 300V BRACKET-PIVOT BULLNOSE A.-*C810* BULLNOSE A. BURNER-I.R. 130416 Model 811, 813, 819, 821 Series 811 073010 072501-SER BASE-ADJUSTER 3/8-24 LR/RF +BRACKET-BURNER *C845* SIDE 072500-SER 079145 +SCREW-3/8-16X1 HEX HEAD CAP BASE-ADJUSTER 3/8/-24 LF/RR 000653 +WASHER-3/8 USS FLAT CR3 075663-SP 072849 BAR-BELLY 020983 +SCREW-SHOULDER 10-32X1/4X.125L X80592 +NUT-10-32 WHIZ FLANGE LOCKNUT BAR A.-RELEASE MATERIAL 072849 X73971 BACKSPLASH A. *C810* 020983 076745 ADAPTOR +SCREW-SHOULDER 10-32X1/4X.125L 058769-2 ADAPTOR-HI TEMP 1/4X1/4 OD +NUT-10-32 WHIZ FLANGE LOCKNUT 079792 ACTUATOR-HOME SWITCH 6 3 1 1 3 4 1 4 6 6 12 6 6 6 2 2 1 6 6 3 1 1 3 1 3 C811 QTY. C81123N000 & L81123NW00 NATURAL GAS - 3 PLATEN GRILLS DESCRIPTION 6 3 1 3 4 1 4 6 6 12 6 6 6 2 2 1 6 6 3 1 3 1 3 L811 QTY. 103 103 103 103 103 103 103 103 103 000 000 000 000 103 103 103 000 000 103 103 000 103 103 000 103 103 103 103 103 103 WARR. CLASS C811 - S/N M1073521 & PRIOR C811 S/N M1073522 & UP UPPER CONTROL CONTROL SWITCH PLATEN COVER C811 S/N M1073521 & PRIOR C811 S/N M1073522 & UP - C813 S/N M1123917 & UP REMARKS Section 9 Parts List Model 811, 813, 819, 821 Series 45 Parts List 017462 073910 076012 076011 073252 080587 073251 X80925 BUSHING-SNAP 5/8ID X 3/4OD-BLK BUSHING-SNAP .391 ID X.500 OD BUTTON-OPERATOR-BLACK BUTTON-OPERATOR-RED CABLE-PLATEN-FRONT CABLE-PLATEN-F-REAR *C810* CABLE-PLATEN-F-REAR CAN A.-GREASE *C810* HEM 077879-C R403022 021277 058770-2 078820 020959 +SWITCH-PRESSURE 240V,3HP +TUBE-TEFLON .188IDX.250OD +TEE-1/4FPT X 1/4MPT X 1/4FPT +TEE-HI TEMP 1/4X1/4 OD +TANK-ACCUMULATOR 10LB-NPT +VALVE-CHECK 1/4MP X70301-02S CONTROL-IGNITOR UTC *M35* 811 070279 CONTROL-HI-LIMIT 450F RESET CONTROL-GRILL TOUCH PAD------> 072695 032129SER2 COMPRESSOR-AIR-230V SERV +MANIFOLD A.-*C842* 079777 CLEVIS-ROD 1/2-20 THD 058771-2 073240 CASTER-GRILL 5" SWIVEL W/LOCK 058769-2 078377 CASTER-5" 7-5/8 STEM +FITTING-HI TEMP 1/4X1/4 OD 9 073619 CARD-INSTALL-GAS GRILL C811 +ADAPTOR-HI TEMP 1/4X1/4 OD 073484 CARD-CHECKOUT GEN MKT INF GAP 069936 053144 BUSHING-SNAP 3/4ID X 1"OD BLK +SLIDE-GREASE CAN *C810* LEFT 027712 BUSHING-SNAP 1-3/8ID X 1-3/4OD 069935 010548 +SLIDE-GREASE CAN *C810* RIGHT 052394 BUSHING-SNAP 11/16 ID X 7/8OD 073016 PART NUMBER BUSHING-FLG .627IDX.12W OILITE +BRACKET-BURNER *C845*-SHORT DESCRIPTION 3 3 1 1 1 1 10' 1 1 1 1 1 3 2 2 1 1 1 1 2 6 6 3 3 6 1 3 5 6 6 6 C811 QTY. 3 3 1 1 1 1 10' 1 1 1 1 1 3 2 2 1 1 1 1 2 6 6 3 3 6 1 3 5 6 6 6 L811 QTY. 103 103 103 103 103 103 000 103 103 103 103 212 103 103 103 103 103 103 103 103 103 103 103 000 000 103 000 000 000 103 103 103 WARR. CLASS *SEE - KIT A.-GRILL CONTROL-GEN MRKT 5/2012 REPLACES X73944 REMARKS Parts List 46 Model 811, 813, 819, 821 Series 072914 073419 072983 072985 GASKET-CONTROL *C842* GASKET-FLUE *C845* GASKET-FRONT SHROUD GASKET-FRONT VIEW PORT *C845* 811 R70113 GASKET-BRAIDED-HI TEMP 079837-10 FUSE-10 AMP BK/MDA-10-R 072695-3 065712 FORM-QUALITY REPORT BY FAX GAUGE-130 PSI 1/8 MPT BACK MNT 072695-8 FITTING-DIFFUSER 1/4 MPT 076299 052560-2 +HOLDER-FUSE-15 A, 250 V 040140-001 FITTING-1/4MPTX1/4OD TUBE 90DG 080879 ELECTRODE-GAS PILOT FILTER-CORCOM 6EH1 073409 ELECTRODE 078329 073810 ELECTRODE FASTENER-SNAP IN 1/4X15/16 073475-23 DIAGRAM-WIRING *C811* 079326-12 X73510 DEFLECTOR A.-FLUE *C811* 080879 X69555 DEFLECTOR A.-FLUE *C811* FAN-BLOWER 60CFM 120/230 VAC 079160 CYLINDER-AIR 6IN STROKE C/C ELECTRODE-GAS PILOT 073668 CORD A.-POWER-250V-30A 4 WIRE 077046 073963 COVER-FRONT *C811* E-RING-3/4 STEEL 068583 COVER A.-USB WATERPROOF 032190 X80589 COVER A.-PLATEN *C810* E-RING 1/4 BLACK PHOS X73256 COVER A.-PLATEN *C810* W/RELEASE BAR X73673 X69621-SER DIODE A.-50 PIV 1A 078721 CONTROL-MOTOR *C811* X73147-12 PART NUMBER CONTROL-LIMIT W/SCREWS +WIRE A.-IGNITOR *C845* DESCRIPTION 3 1 2 3 15' 1 1 1 1 1 6 3 24 3 3 12 6 3 3 3 1 1 1 3 1 1 3 3 3 3 3 C811 QTY. 3 1 2 3 15' 1 1 1 1 1 6 3 24 3 3 12 6 3 3 1 1 3 1 1 3 3 3 3 3 L811 QTY. 000 000 000 000 000 103 103 000 000 103 103 103 000 103 103 000 000 000 103 103 103 000 103 103 103 103 103 103 103 103 212 103 103 WARR. CLASS C811 S/N M1073521 & PRIOR C811 S/N M1073522 & UP C811 S/N M1073521 & PRIOR C811 S/N M1073522 & UP 1/17/2012 REPLACES 073963 PLATEN REMARKS Model 811, 813, 819, 821 Series 47 Parts List 072529 073436 073444 073095 073096 073097 073425 073369 073454 073941 R30317 HARNESS-POWER SUPPLY-NEG HARNESS-PRESSURE SWITCH HARNESS-SSR-LEFT*C845* HARNESS-SSR-MIDDLE*C845 HARNESS-SSR-RIGHT*C845* HARNESS-SWITCH HARNESS-TOUCH-CONTROL*C810-11* HARNESS-TRANSFORMER A.-115V HOSE ASSEMBLY-FLEXIBLE GAS HOSE-BEV.-.250IDX.438OD-100' 811 073460 073471-L HARNESS-HIGH LIMIT C845/C811 HARNESS-PCB/GR SWITCH *C832* 073437 HARNESS-GAS VALVE TREE HARNESS-MC BOARD SUPPLY-24V 073426 HARNESS-GAS VALVE 073438 069717 HARNESS-FAN *C819* HARNESS-IGNITOR-GROUND 069716 HARNESS-FAN *C819* 073429-R 073422 HARNESS-COMPRESSOR *C845/C81 073429-M 073608 HARNESS-BLOWER HARNESS-IDC BOARD 073428 HARNESS-12V-POSITIVE-BOARD HARNESS-IDC BOARD 073427 HARNESS-12V-NEGATIVE-BOARD 073429-L 073892 HARNESS A.-MOTOR *C820* HARNESS-IDC BOARD X72743 HARNESS A.-COMP. VALVE *C842* 073471-R 080588-B HANDLE-PLATEN HARNESS-HIGH LIMIT C845/C811 073250 HANDLE-PLATEN 073471-M 073440 GUIDE-PATTY PLACEMENT GEN MKT HARNESS-HIGH LIMIT C845/C811 028534-1 PART NUMBER GUARD-FAN DESCRIPTION 5' 1 1 3 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 2 2 1 3 1 1 3 1 3 1 1 C811 QTY. 5 1 1 3 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 2 2 1 3 1 1 3 1 3 1 1 L811 QTY. 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 WARR. CLASS TUBE-NYLOBRADE 1/4ID X 7/16OD CONTROL A.- UPPER CONTROL A.- UPPER CONTROL A.- UPPER REMARKS Parts List 48 Model 811, 813, 819, 821 Series 024298 001082 073442 075888 000653 X80680 SCREW-10-32X3/8 SLTD TRUSS SCREW-3/8-16X1 HEX HEAD CAP SHEET-RELEASE BOX(9) GEN MRK STRIP-REPLACEMENT WASHER-3/8 USS FLAT CR3 KIT A.-ACCESSORY*LONG PLTN* 072658 072986 X81005 X81004 X81006 X73109-02 LABEL-WARN GRILL MCD AUTH SVC LENS-MICA *C845* LINE A.-GAS-CENTER *C811* LINE A.-GAS-LEFT *C811* LINE A.-GAS-RIGHT *C811* MANIFOLD A.-*C845* GAS 811 076370 075484 ELBOW-3/8 MPT X 5/16 073443 000653 WASHER-3/8 USS FLAT CR3 LABEL-ELEC-CAUTION 075888 STRIP-REPLACEMENT LABEL-CONTROL COMPONENTS 080595 SHEET-RELEASE *C810* X78330-SER 001082 SCREW-3/8-16X1 HEX HEAD CAP KIT A.-GREASE SHIELD* 024298 SCREW-10-32X3/8 SLTD TRUSS X73474-SER 075887 SCRAPER-TEFLON WIPER KIT A.-GRILL CONTROL-GEN MRKT 080594 RETAINER-SHEET RELEASE *C810 072673 075887 SCRAPER-TEFLON WIPER CLIP-RELEASE MATERIAL-W/TAB 072845 X73459 KIT A.-ACCESSORY*INF GAP GEN RETAINER-SHEET RELEASE *C842* 074948 KIT A.-3FT RESTRAIN CABLE 072673 073106 CLIP-RELEASE MATERIAL-W/TAB 079810 INSULATION-SHROUD*C845*IN 051742 PART NUMBER INSULATOR-TEFLON-2 HOLE +CLAMP-HOSE 7/16-WIRE DICHROMAT DESCRIPTION 3 1 1 1 1 3 3 1 1 3 3 2 1 1 2 9 1 3 6 1 1 3 9 3 C811 QTY. 3 1 1 1 1 3 3 1 1 3 3 2 1 1 2 9 1 3 6 1 1 3 9 3 L811 QTY. 103 103 103 103 103 000 000 000 000 000 312 000 000 000 000 000 000 103 000 000 000 000 000 000 000 000 103 000 000 103 000 000 000 WARR. CLASS REPLACES X73274-SER REMARKS Model 811, 813, 819, 821 Series 49 Parts List 078907 079329-02 PLUG-3/8MPT-BLACK VALVE-GAS REDUNDANT 3-1/2 WC 072695-4 VALVE-PRESSURE RELIEF 70 PSI 073826-005 076554-40 076554-53 X73993 X73979 X69550 073990 073989 073991 ORIFICE A.-IGNITOR ORIFICE-HEX PLUG GAS-#40 ORIFICE-HEX PLUG GAS-#53 PANEL A.-BACK SERVICE *C811* PANEL A.-FRONT-LOWER *C810* PANEL A.-FRONT UPPER *C81 PANEL-SIDE UPPER-LT *C810* PANEL-SIDE UPPER-RT *C810* PANEL-SIDE-LOWER *C810* RIGH 811 052733-118 O-RING-1-1/16OD X .103W 6 1 1 1 1 1 1 3 3 3 6 12 1 1 1 1 1 1 3 3 3 6 12 017523 +NUT-1/4-20 WHIZ FLANGE LOCK 052733-120 073249 +SCREW-SHOULDER 5/16 X 1 O-RING-1-3/16OD X .103W 073247 6 6 017523 +NUT-1/4-20 WHIZ FLANGE LOCK 3 1 1 MOTOR-GEAR *M32/35* STEPPER V3 3 1 1 3 1 3 1 1 1 1 3 1 3 1 1 1 L811 QTY. 6 080603 028534-1 3 1 3 1 1 1 1 3 1 3 1 1 1 C811 QTY. 073249 +SCREW-SHOULDER 5/16 X 1 MOTOR-GEAR W/CONN *C810* +GUARD-FAN 062253-27 072695-1 VALVE-SOLENOID 3 WAY 12 VDC MOTOR-FAN 95.3 CFM 2700 RPM 072695-2 REGULATOR-PRESSURE 0-120 PSI X80578 072695-3 GAUGE-130 PSI 1/8 MPT BACK MNT MOTOR A.-MOUNT *C810* 072695-8 FITTING-DIFFUSER 1/4 MPT X73273-SER 072695-6 FITTING-SWIVEL ELBOW 1/4 OD MOTOR A.-MOUNT *C810* 072695-5 FITTING-SWIVEL ELBOW 1/4 OD 072695 077364 FITTING-REDUCER-1/2FPT-3/8FPT MANIFOLD A.-*C842* 078906 PART NUMBER FITTING-CROSS 3/8FPT-BLACK DESCRIPTION 103 103 103 103 103 103 103 103 103 000 000 000 103 103 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 WARR. CLASS C811 S/N M1073522 & UP C811 S/N M1073522 & UP C811 S/N M1073522 & UP C811 S/N M1073522 & UP C811 S/N M1073522 & UP C811 S/N M1073522 & UP REAR PLATEN ARM GEAR MOTOR USED PRIOR TO M2091954 GEAR MOTOR S/N M2091955 & UP - REPLACES 073247 C811 S/N M1073522 & UP MANIFOLD A.-GAS REMARKS Parts List 50 Model 811, 813, 819, 821 Series 053361 050988 072662 073248-L PLUG-HOLE 1-3/8 DIA.-BLACK PLUG-HOLE 3/8 DIA BLACK PLASTI PULLEY-PLATEN CABLE PULLEY-PLATEN-LEFT 050869-27 074210-02 RELAY-4P-40A 200/240 COIL RELAY-SS 25A NON-ALARM 240 VAC 811 072695-2 039536 073248-R REGULATOR-PRESSURE 0-120 PSI +SCREW-1/4-20X3/8 SOCKET SET PULLEY-PLATEN-RIGHT 039536 027132 +SCREW-1/4-20X3/8 SOCKET SET 010077 079576 PLATE-AIR SHUTTER BOTTOM PLUG-HOLE 1-3/4 DIA. X73570 PLATE A.-DOOR HINGE-R PLUG-HOLE 7/8 DIA. BLACK X73569 PLATE A.-DOOR HINGE-L 073808 X79485 PLATE A.-AIR SHUTTER SLIDE PLUG A.-USB CABLE 080646 PIN-SPRING UPPER *C810* X73522-23 072542 PIN-SPRING UPPER *C842* X73741-23 073261 PANEL-SIDE-LOWER *C810* RIGHT PLATEN A.-2600W 208V *C811* 073262 PANEL-SIDE-LOWER *C810* LEFT PLATEN A.-SERVICE *C820* 2600W 073650 PANEL-FRONT-LOWER *C812* 072982 073432 PANEL-BACK-LOWER PLATE-HEAT TRANSFER X72965 PANEL A.-SIDE UPPER*832/835*RT 073463 X72962 PANEL A.-SIDE UPPER*832/835*LT PLATE-AIR SHUTTER TOP *C845* X73373 PANEL A.-FRONT UPPER *C811* 079482 X73513 PANEL A.-BACK SERVICE *C811* PLATE-AIR SHUTTER SPACER *M35* 073992 PART NUMBER PANEL-SIDE-LOWER *C810* LEFT DESCRIPTION 6 1 1 3 3 3 3 6 2 2 3 1 3 3 6 3 3 3 1 1 3 6 1 1 1 1 1 1 1 1 1 C811 QTY. 6 1 1 3 3 3 3 6 2 2 3 1 3 3 9 3 3 3 3 6 1 L811 QTY. 103 103 103 000 103 000 103 103 103 000 000 000 103 212 212 103 103 103 103 103 103 103 000 000 103 103 103 103 103 103 103 103 103 WARR. CLASS UPPER CONTROL MANIFOLD A.-*C842* C811 S/N M1073521 & PRIOR C811 S/N M1073521 & PRIOR C811 S/N M1073521 & PRIOR C811 S/N M1073521 & PRIOR C811 S/N M1073521 & PRIOR C811 S/N M1073521 & PRIOR C811 S/N M1073521 & PRIOR-FRONT CONTROL C811 S/N M1073521 & PRIOR C811 S/N M1073522 & UP REMARKS Model 811, 813, 819, 821 Series 51 Parts List 052010 072849 073249 R700033 R70003 079952 X73597 072926 072927 078285 SCREW-SHOULDER 3/8X3-1/4 SCREW-SHOULDER 10-32X1/4X.125L SCREW-SHOULDER 5/16 X 1 SEALANT-GORE-TEX 1/4 UNCOMP. SEALANT-JOINT 1/2 IN TEADIT SEAL-ARM *M32/35* SHIELD A.-HEAT *C811/C845* SHIELD-COUPLING FRONT SHIELD-COUPLING REAR SHIELD-GREASE *M 22* 6 073962 073004 073003 021625 079074 076657 072617 072542 080649 080646 SHROUD-OUTER BACK *C811* RIG SHROUD-OUTER BACK *C845* LEFT SHROUD-OUTER BACK *C845* RIGHT SOCKET-.084 OD/14-20 AWG-STRIP SPACER-HEAT TRANSFER PLATE SPACER-SHROUD SPRING-EXTENSION LATCH *C842* +PIN-SPRING UPPER *C842* SPRING-EXTENSION LATCH *C 073764 SWITCH-HOME POSITION 811 079792 073336 SUPPLY-POWER-10W 12VDC +ACTUATOR-HOME SWITCH *32/35* 040280-020 STANDOFF-NYLON 6-32 SNP/THREAD +PIN-SPRING UPPER *C810* 12 073961 SHROUD-OUTER BACK *C811* LEF 3 3 3 12 6 12 8 54 6 1 1 1 1 3 3 3 12 8 54 6 1 1 3 X80585 SHROUD A.-PLATEN *C810* 3 X72835 1 9 SHROUD A.-PLATEN *C842* 1 9 9 24 6 6 3 3 6 5' 15' 6 6 12 18 3 L811 QTY. X73965 072467-1 SHIELD-PLATE TUBE INNER 9 24 6 6 3 3 6 5' 17' 6 6 12 18 3 C811 QTY. SHROUD A.-COMBINATION *C811* 072467 SHIELD-PLATE TUBE 078329 058381 SCREW-SHOULDER 4-40X.3755 SOC +FASTENER-SNAP IN 1/4X15/16 073304 PART NUMBER ROD-AIR SHUTTER ADJUST *C845* DESCRIPTION 103 103 103 000 000 000 000 000 000 000 103 103 103 103 103 103 103 103 103 103 000 103 103 103 103 000 000 000 103 103 103 103 103 WARR. CLASS PLATEN SPRING C811 S/N M1073521 & PRIOR C811 S/N M1073521 & PRIOR S/N C811 M1073522 & UP S/N C811 M1073522 & UP SEE - KIT A.-SHIELD X78330-SER OPERATOR BUTTONS ARM/BACKSPLASH REMARKS Parts List 52 Model 811, 813, 819, 821 Series 079800-24 073973 073974 TRANS.-100VA 120/208/240 PRI TRIM-CORNER *C810* RIGHT FRONT TRIM-CORNER *C810* LEFT FRONT 072695-4 072695-1 X51733-C 073013 VALVE-PRESSURE RELIEF 70 PSI VALVE-SOLENOID 3 WAY 12 VDC VARISTOR A.-230VAC W/#10 SPADE WINDOW-FRONT VIEW PORT 811 072985 079329-02 VALVE-GAS REDUNDANT 3-1/2 WC 072986 020959 VALVE-CHECK 1/4MP +GASKET-FRONT VIEW PORT *C 078332 VALVE-CHECK W/#69 ORIFICE M22 +LENS-MICA *C845* R403022 051742 TUBE-TEFLON .188IDX.250OD +CLAMP-HOSE 7/16-WIRE DICHROMAT TUBE-NYLOBRADE 1/4ID X 7/16OD X73640 076222-K THERMOCOUPLE K TUBE A.-GAS BACK *C811* 079622 THERMOCOUPLE-K TYPE SS BRAID R403021 053995 TERMINAL-FERRULE .5MM *M32/3 073264 080610 TERMINAL-FERRULE 16-22AWG TUBE-.170ID X .250OD 058770-2 TEE-HI TEMP 1/4X1/4 OD TRIM-CORNER *C810* RIGHT 021277 TEE-1/4FPT X 1/4MPT X 1/4FPT 073263 078820 TANK-ACCUMULATOR 10LB-NPT TRIM-CORNER *C810* LEFT 075780 SWITCH-SCREW TERMINAL 073988 076989-WP SWITCH-ROCKER-DPST-10AMP IP65 TRIM-CORNER *C810* LEFT REAR 079442 SWITCH-PUSHBUTTON-SPST 073987 077879-C SWITCH-PRESSURE 240V,3HP TRIM-CORNER *C810* RIGHT REAR 074314 PART NUMBER SWITCH-PRESSURE DESCRIPTION 3 3 3 2 3 1 3 1 3 10' 3 1 10' 1 1 1 1 1 1 3 6 6 32 15 1 1 1 3 1 3 1 3 C811 QTY. 3 3 3 2 3 1 3 1 3 10' 3 1 10' 1 1 1 1 3 6 6 32 15 1 1 1 3 1 1 3 L811 QTY. 000 000 103 103 103 103 103 103 103 000 000 000 103 000 103 103 103 103 103 103 103 103 103 000 000 103 103 103 103 103 103 103 103 WARR. CLASS AIR COMPRESSOR MANIFOLD MANIFOLD MANIFOLD A.-*C845* GAS AIR COMPRESSOR AIR COMPRESSOR USE R30317 HOSE-BEV.-.250IDX.438OD-100' C811 S/N M1073521 & PRIOR C811 S/N M1073521 & PRIOR S/N M1073522 & UP S/N M1073522 & UP S/N M1073522 & UP S/N M1073522 & UP AIR COMPRESSOR AIR COMPRESSOR LATCH SWITCH C811 S/N M1073521 & PRIOR COMPRESSOR A.-AIR UPPER CONTROL REMARKS Model 811, 813, 819, 821 Series 53 Parts List X73274-SER 073451-M MAN-OPER C811 JACK-IN-BOX 074978 079567 079567-F 076389-CAN 078075-CAN 072658-CAN LABEL-FUSE REPLACEMENT 7A LABEL-INST-LIGHT*15E* LABEL-INST-LIGHT*15E*FREN LABEL-NOTICE-CASTERS-CANADA LABEL-WARN-GAS GRILL-CANADA LABEL-WARN-GRILL-MCD-SVC-CANADA 073475-28 DIAGRAM-WIRING *C811* 073475-75 X78996-40 DIAGRAM-WIRING *C811* HV1 FILTER A.-*M15* WHT/BLK 811 073422 074165 CONTROL-HI-LIMIT 550F NO HARNESS-COMPRESSOR 081041-03 CONTROL-IGNITION X79573-36 024329 BLOCK-TERMINAL 5P 20A, 30 HARNESS A.-GAS VALVE 051647 BLOCK-TERMINAL 4P 1,2,L1, 075288 073033 BLOCK-TERMINAL 2P .25 SPD GUARD-LENSE 073423 BLOCK-TERMINAL 1P C81175NW00 & L81175NW00 - 400V 50HZ 3N (4 WIRE) X73522-28 PLATEN A.-2600W 230V *C811* C81128NW00 073625FCM 075484-CAN LABEL-ELEC-CAUTION-CANADA MAN-OPER C811/C813 FR-CANADA 073619FC CARD-INSTALL-C811 FRENCH- C81123N879 - CANADA X73404 KIT A.-GRILL CONTROL-JIB X73147-12 PART NUMBER GAGE A.-GAP *C810-C811* JIB C81123N921 - JIB WIRE A.-IGNITOR DESCRIPTION 1 3 3 1 1 3 1 2 1 2 2 1 1 3 1 1 1 1 1 1 1 1 3 1 3 C811 QTY. 1 3 3 1 1 3 1 2 1 2 2 3 L811 QTY. 103 103 103 103 000 103 103 103 103 103 103 000 212 000 000 000 000 000 000 000 000 000 000 212 000 103 WARR. CLASS NEED SERVICE PART NUMBER C811 S/N M1073522 & UP REMARKS Parts List 54 Model 811, 813, 819, 821 Series 073424 X81823-SER 075699-SYM 078075 079567 076389 078075 079538-40 076554-51 074210-02 052111-03 HARNESS-SWITCH KIT A.-GAS VALVE 24 VAC LABEL-CONTROL PANEL-INTL LABEL-WARN-GAS GRILL LABEL-INST-LIGHT*15E* LABEL-NOTICE-CASTERS LABEL-WARN-GAS GRILL LABEL-WIRING ORIFICE-HEX PLUG GAS-#51 RELAY-SS 25A NON ALARM RELAY-DPDT 100UA TO 7A 1/ 811 059993 081709 HARNESS-MC TRANS TO BLOCK TRANS.-CONT.-80VA 230V/24 073460 HARNESS-MC BOARD SUPPLY-2 052112 069717 HARNESS-FAN *C819* SOCKET-RELAY-FOR USE W/05 069716 PART NUMBER HARNESS-FAN *C819* DESCRIPTION 3 3 3 6 3 1 1 1 1 1 2 3 1 1 1 1 1 C811 QTY. 3 3 3 6 3 1 1 1 1 1 2 3 1 1 1 1 1 L811 QTY. 103 103 103 103 103 000 000 000 000 000 000 103 103 103 103 103 103 WARR. CLASS REMARKS 130416 Model 811, 813, 819, 821 Series 55 Parts List PART NUMBER X72843 BAR A.-RELEASE MATERIAL 080647 076013 073423 073033 051331 076451 X73975 073334 BEARING .628 X .813 X 2.0 BLOCK-CONTACT 1 NO BLOCK-TERMINAL 1P BLOCK-TERMINAL 2P .25 SPD-24X BLOCK-TERMINAL 3P 20A, 300V BRACKET-PIVOT BULLNOSE A.-*C810* BURNER-I.R. 813 052394 072541 BEARING .753 X 1.000 X 2.000 BUSHING-FLG .627IDX.12W OILITE 080648 BEARING-FLANGE 5/8 X 15/16 073016 077042 BEARING-FLANGE 3/4 X 15/16 +BRACKET-BURNER-SHORT 078730 BEARING 3/4 ID-SELF ALIGN 073010 072501-SER BASE-ADJUSTER 3/8-24 LR/RF +BRACKET-BURNER SIDE 072500-SER 079145 +SCREW-3/8-16X1 HEX HEAD CAP BASE-ADJUSTER 3/8/-24 LF/RR 000653 +WASHER-3/8 USS FLAT CR3 075663-SP 072849 +SCREW-SHOULDER 10-32X1/4X.125L BAR-BELLY 020983 X80592 +NUT-10-32 WHIZ FLANGE LOCKNUT BAR A.-RELEASE MATERIAL 072849 X69628 BACKSPLASH A. *C813* +SCREW-SHOULDER 10-32X1/4X.125L 076745 ADAPTOR 020983 058769-2 ADAPTOR-HI TEMP 1/4X1/4 OD +NUT-10-32 WHIZ FLANGE LOCKNUT 079792 ACTUATOR-HOME SWITCH 4 6 6 3 1 2 4 1 4 6 4 8 4 4 4 2 2 1 4 4 2 1 3 1 2 4 6 6 3 1 2 4 1 4 6 4 8 4 4 4 2 2 1 4 4 2 1 3 1 2 C813 L813 QTY. QTY. C81323NCL2 (PLATEN DOUBLE LEFT) & L81323NW79 (ROHS CANADA) NATURAL GAS DESCRIPTION 103 103 103 103 103 103 103 103 103 103 000 000 103 000 103 103 103 000 000 103 103 000 103 103 000 103 103 103 103 103 WARR. CLASS COMMENTS Parts List 56 Model 811, 813, 819, 821 Series 076011 073252 080587 073251 X80925 X73944 BUTTON-OPERATOR-RED CABLE-PLATEN-FRONT CABLE-PLATEN-F-REAR *C810* CABLE-PLATEN-F-REAR CAN A.-GREASE *C810* HEM CAN A.-GREASE *C810* 073129 072695-8 077879-C R403022 021277 058770-2 078820 020959 +MANIFOLD A.-*C832* +FITTING-DIFFUSER 1/4 MPT +SWITCH-PRESSURE 240V,3HP +TUBE-TEFLON .188IDX.250OD +TEE-1/4FPT X 1/4MPT X 1/4FPT +TEE-HI TEMP 1/4X1/4 OD +TANK-ACCUMULATOR 10LB-NPT +VALVE-CHECK 1/4MP 813 CONTROL-GRILL TOUCH PAD------> 072695 032129SER2 COMPRESSOR-AIR-230V SERV 058771-2 079777 CLEVIS-ROD 1/2-20 THD +MANIFOLD A.-*C842* 073240 CASTER-GRILL 5" SWIVEL W/LOCK +FITTING-HI TEMP 1/4X1/4 OD 9 078377 CASTER-5" 7-5/8 STEM 058769-2 073619FC CARD-INSTALL-C811 FRENCH- +ADAPTOR-HI TEMP 1/4X1/4 OD 073619 CARD-INSTALL-GAS GRILL C811 073484 076012 BUTTON-OPERATOR-BLACK CARD-CHECKOUT GEN MKT INF GAP 073910 BUSHING-SNAP .391 ID X.500 OD 069936 017462 BUSHING-SNAP 5/8ID X 3/4OD-BLK +SLIDE-GREASE CAN *C810* LEFT 053144 BUSHING-SNAP 3/4ID X 1"OD BLK 069935 027712 +SLIDE-GREASE CAN *C810* RIGHT 010548 BUSHING-SNAP 1-3/8ID X 1-3/4OD PART NUMBER BUSHING-SNAP 11/16 ID X 7/8OD DESCRIPTION 1 1 1 1 10' 1 1 1 1 1 1 2 2 2 1 1 1 1 2 2 4 4 3 3 6 1 3 5 6 1 1 1 1 10' 1 1 1 1 1 1 2 2 2 1 1 1 1 1 2 4 4 3 3 6 1 3 5 6 C813 L813 QTY. QTY. 103 103 103 103 000 103 103 000 103 103 103 *** 103 103 103 000 000 000 103 103 103 103 103 103 103 103 103 103 000 000 000 103 WARR. CLASS COMMENTS Model 811, 813, 819, 821 Series 57 Parts List 072914 073419 072983 072985 028534-1 GASKET-CONTROL GASKET-FLUE GASKET-FRONT SHROUD GASKET-FRONT VIEW PORT GUARD-FAN 813 R70113 GASKET-BRAIDED-HI TEMP 079837-10 FUSE-10 AMP BK/MDA-10-R 072695-3 065712 FORM-QUALITY REPORT BY FAX GAUGE-130 PSI 1/8 MPT BACK MNT 072695-8 FITTING-DIFFUSER 1/4 MPT 076299 052560-2 FITTING-1/4MPTX1/4OD TUBE 90DG +HOLDER-FUSE-15 A, 250 V 040140-001 FILTER-CORCOM 6EH1 X73673 DIODE A.-50 PIV 1A 078329 073725-23 DIAGRAM-WIRING *C813* FASTENER-SNAP IN 1/4X15/16 X69555 DEFLECTOR A.-FLUE *C811* 079326-12 079160 CYLINDER-AIR 6IN STROKE C/C 077046 073668 CORD A.-POWER-250V-30A 4 WIRE FAN-BLOWER 60CFM 120/230 VAC 073963 COVER-FRONT *C811* E-RING-3/4 STEEL 073809 COVER A.-USB WATERPROOF 032190 068583 COVER A.-USB WATERPROOF E-RING 1/4 BLACK PHOS X80589 COVER A.-PLATEN *C810* 080879 X73256 COVER A.-PLATEN *C810* W/RELEASE BAR ELECTRODE-GAS PILOT X69621-SER CONTROL-MOTOR *C811* X73147-12 +WIRE A.-IGNITOR 078721 X70301-02S CONTROL-LIMIT W/SCREWS 070279 CONTROL-IGNITOR UTC PART NUMBER CONTROL-HI-LIMIT 450F RESET DESCRIPTION 1 3 1 2 3 15' 1 1 1 1 1 6 3 24 3 8 6 3 3 1 1 2 1 1 3 3 2 3 2 3 3 3 1 3 1 2 3 15' 1 1 1 1 1 6 3 24 3 8 6 3 3 1 1 2 1 1 3 2 3 2 3 3 3 C813 L813 QTY. QTY. 000 000 000 000 000 000 103 103 000 000 103 103 103 000 103 000 000 103 000 000 103 103 103 103 103 103 103 103 212 103 103 103 103 WARR. CLASS COMMENTS Parts List 58 Model 811, 813, 819, 821 Series 073731 073095 073096 073425 073369 073454 073941 R30317 HARNESS-RHT-GAS-DETECT HARNESS-SSR-LEFT HARNESS-SSR-MIDDLE HARNESS-SWITCH HARNESS-TOUCH-CONTROL*C810-11* HARNESS-TRANSFORMER A.-115V HOSE ASSEMBLY-FLEXIBLE GAS HOSE-BEV.-.250IDX.438OD-100' 813 051742 073444 HARNESS-PRESSURE SWITCH +CLAMP-HOSE 7/16-WIRE DICHROMAT 073436 HARNESS-POWER SUPPLY-NEG 073471-M HARNESS-HIGH LIMIT C845/C811 072529 073471-L HARNESS-HIGH LIMIT C845/C811 073460 073437 HARNESS-GAS VALVE TREE HARNESS-PCB/GR SWITCH 073426 HARNESS-GAS VALVE HARNESS-MC BOARD SUPPLY-24V 069717 HARNESS-FAN *C819* 073438 069716 HARNESS-FAN *C819* HARNESS-IGNITOR-GROUND 073422 HARNESS-COMPRESSOR *C845/C81 073429-R 073608 HARNESS-BLOWER 073429-M 073428 HARNESS-12V-POSITIVE-BOARD HARNESS-IDC BOARD 073427 HARNESS-12V-NEGATIVE-BOARD HARNESS-IDC BOARD 073892 HARNESS A.-MOTOR *C820* 073429-L X73703 HARNESS A.-COMP. VALVE *C812* HARNESS-IDC BOARD 080588-B HANDLE-PLATEN, BLK PENTAT 073471-R 073250 HARNESS-HIGH LIMIT C845/C811 073440 HANDLE-PLATEN PART NUMBER GUIDE-PATTY PLACEMENT GEN MKT DESCRIPTION 3 5' 1 1 3 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 2 2 1 3 1 1 2 1 2 1 3 5' 1 1 3 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 2 2 1 3 1 1 2 1 3 1 C813 L813 QTY. QTY. 000 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 WARR. CLASS COMMENTS Model 811, 813, 819, 821 Series 59 Parts List 080595 075888 000653 X73678 SHEET-RELEASE *C810* STRIP-REPLACEMENT WASHER-3/8 USS FLAT CR3 KIT A.-ACCESSORY*INF GAP GEN 075484-CAN 074978 079567 079567-F 076389-CAN 072658 LABEL-ELEC-CAUTION-CANADA LABEL-FUSE REPLACEMENT 7A LABEL-INST-LIGHT*15E* LABEL-INST-LIGHT*15E*FREN LABEL-NOTICE-CASTERS-CANA LABEL-WARN GRILL MCD AUTH SVC 813 075484 078329 FASTENER-SNAP IN 1/4X15/16 LABEL-ELEC-CAUTION 078285 SHIELD-GREASE *M 22* 073443 000653 WASHER-3/8 USS FLAT CR3 X78330-SER 075888 STRIP-REPLACEMENT LABEL-CONTROL COMPONENTS 073442 SHEET-RELEASE BOX(9) GEN MRK KIT A.-GREASE SHIELD* 001082 SCREW-3/8-16X1 HEX HEAD CAP X73474-SER 024298 SCREW-10-32X3/8 SLTD TRUSS KIT A.-GRILL CONTROL-GEN MRKT 075887 SCRAPER-TEFLON WIPER 072845 001082 SCREW-3/8-16X1 HEX HEAD CAP RETAINER-SHEET RELEASE *C842* 024298 SCREW-10-32X3/8 SLTD TRUSS 072673 075887 SCRAPER-TEFLON WIPER CLIP-RELEASE MATERIAL-W/TAB 080594 X80680 KIT A.-ACCESSORY*LONG PLTN* 072673 074948 KIT A.-3FT RESTRAIN CABLE RETAINER-SHEET RELEASE *C810 073106 CLIP-RELEASE MATERIAL-W/TAB 079810 INSULATION-SHROUD PART NUMBER INSULATOR-TEFLON-2 HOLE DESCRIPTION 3 1 1 2 3 24 4 2 1 1 2 9 1 2 4 1 1 3 6 1 1 1 1 1 1 2 3 2 1 1 2 9 1 3 6 1 1 3 6 C813 L813 QTY. QTY. 000 000 000 000 000 000 000 000 103 312 000 103 000 000 000 000 000 000 103 000 000 000 000 000 000 000 000 103 000 000 103 000 000 WARR. CLASS COMMENTS Parts List 60 Model 811, 813, 819, 821 Series 072695-4 VALVE-PRESSURE RELIEF 70 PSI 073247 073249 017523 MOTOR-GEAR *M32/35* STEPPER V3 +SCREW-SHOULDER 5/16 X 1 +NUT-1/4-20 WHIZ FLANGE LOCK 813 052733-120 017523 O-RING-1-3/16OD X .103W 073249 +NUT-1/4-20 WHIZ FLANGE LOCK 080603 028534-1 +SCREW-SHOULDER 5/16 X 1 MOTOR-GEAR W/CONN *C810* +GUARD-FAN 062253-27 072695-1 VALVE-SOLENOID 3 WAY 12 VDC MOTOR-FAN 95.3 CFM 2700 RPM 072695-2 REGULATOR-PRESSURE 0-120 PSI X80578-SER 072695-3 GAUGE-130 PSI 1/8 MPT BACK MNT MOTOR A.-MOUNT *C810* 072695-8 FITTING-DIFFUSER 1/4 MPT X73273-SER 072695-6 FITTING-SWIVEL ELBOW 1/4 OD MOTOR A.-MOUNT *C810* 072695-5 073129 FITTING-SWIVEL ELBOW 1/4 OD MANIFOLD A.-*C832* 079329-02 VALVE-GAS REDUNDANT 3-1/2 WC X73109-02 MANIFOLD A.-GAS 078907 073625FCM MAN-OPER C811/C813 FR-CAN PLUG-3/8MPT-BLACK 073625-M MAN-OPER C811/C813 077364 X81006 LINE A.-GAS-RIGHT *C811* 078906 X81004 LINE A.-GAS-LEFT *C811* FITTING-REDUCER-1/2FPT-3/8FPT X81005 LINE A.-GAS-CENTER *C811* FITTING-CROSS 3/8FPT-BLACK 072986 LENS-MICA 076370 078075-CAN ELBOW-3/8 MPT X 5/16 072658-CAN LABEL-WARN-GAS GRILL-CANA PART NUMBER LABEL-WARN-GRILL-MCD-SVC- DESCRIPTION 8 4 4 2 4 4 1 1 2 1 2 1 1 1 1 2 1 3 1 1 1 3 1 1 1 1 1 3 8 4 4 2 1 1 2 1 2 1 1 1 1 2 1 3 1 1 1 3 1 1 1 1 1 1 3 1 3 C813 L813 QTY. QTY. 000 000 103 103 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 000 000 103 103 103 000 000 000 WARR. CLASS COMMENTS Model 811, 813, 819, 821 Series 61 Parts List 050988 072662 073248-L PLUG-HOLE 3/8 DIA BLACK PLASTI PULLEY-PLATEN CABLE PULLEY-PLATEN-LEFT 051890-27 074210-02 RELAY-3P-50A 208/240 COIL RELAY-SS 25A NON-ALARM 240 VAC 813 072695-2 039536 073248-R REGULATOR-PRESSURE 0-120 PSI +SCREW-1/4-20X3/8 SOCKET SET PULLEY-PLATEN-RIGHT 039536 053361 PLUG-HOLE 1-3/8 DIA.-BLACK +SCREW-1/4-20X3/8 SOCKET SET 027132 PLUG-HOLE 1-3/4 DIA. 079576 PLATE-AIR SHUTTER BOTTOM 010077 X79485 PLATE A.-AIR SHUTTER SLIDE 073808 080646 PIN-SPRING UPPER *C810* PLUG-HOLE 7/8 DIA. BLACK 072542 PIN-SPRING UPPER *C842* PLUG A.-USB CABLE 073992 PANEL-SIDE-LOWER *C810* LEFT X73522-23 073991 PANEL-SIDE-LOWER *C810* RIGH PLATEN A.-2600W 208V 073989 PANEL-SIDE UPPER-RT *C810* X73741-23 073990 PANEL-SIDE UPPER-LT *C810* 072982 X69550 PANEL A.-FRONT UPPER *C81 PLATEN A.-SERVICE *C820* 2600W X73979 PANEL A.-FRONT-LOWER *C810* PLATE-HEAT TRANSFER X73993 PANEL A.-BACK SERVICE *C811* 073463 076554-53 ORIFICE-HEX PLUG GAS-#53 PLATE-AIR SHUTTER TOP 076554-40 ORIFICE-HEX PLUG GAS-#40 079482 073826-005 PLATE-AIR SHUTTER SPACER 052733-118 ORIFICE A.-IGNITOR PART NUMBER O-RING-1-1/16OD X .103W DESCRIPTION 4 1 1 2 2 2 2 4 2 2 3 1 3 2 7 3 3 3 3 4 1 1 1 1 1 1 1 3 3 3 4 4 1 1 2 2 2 2 4 2 2 3 1 3 2 7 3 3 3 3 4 1 1 1 1 1 1 1 3 3 3 4 C813 L813 QTY. QTY. 103 103 103 000 103 000 103 103 103 000 000 000 103 212 212 103 103 103 103 103 000 000 103 103 103 103 103 103 103 103 103 103 000 WARR. CLASS COMMENTS Parts List 62 Model 811, 813, 819, 821 Series 052010 072849 073249 R700033 R70003 079952 X73597 072926 072927 078285 SCREW-SHOULDER 3/8X3-1/4 SCREW-SHOULDER 10-32X1/4X.125L SCREW-SHOULDER 5/16 X 1 SEALANT-GORE-TEX 1/4 UNCOMP. SEALANT-JOINT 1/2 IN TEADIT SEAL-ARM *M32/35* SHIELD A.-HEAT *C811/C845* SHIELD-COUPLING FRONT SHIELD-COUPLING REAR SHIELD-GREASE *M 22* 079074 076657 072617 072542 080649 080646 SPACER-HEAT TRANSFER PLATE SPACER-SHROUD SPRING-EXTENSION LATCH *C842* +PIN-SPRING UPPER *C842* SPRING-EXTENSION LATCH *C +PIN-SPRING UPPER *C810* 077879-C SWITCH-PRESSURE 240V,3HP 813 074314 079792 SWITCH-PRESSURE +ACTUATOR-HOME SWITCH *32/35* 073764 021625 SOCKET-.084 OD/14-20 AWG-STRIP SWITCH-HOME POSITION 073962 SHROUD-OUTER BACK *C811* RIG 073336 073961 SHROUD-OUTER BACK *C811* LEF 040280-020 X80585 SHROUD A.-PLATEN *C810* SUPPLY-POWER-10W 12VDC X72835 SHROUD A.-PLATEN *C842* STANDOFF-NYLON 6-32 SNP/THREAD X73965 072467-1 SHIELD-PLATE TUBE INNER SHROUD A.-COMBINATION *C811* 072467 SHIELD-PLATE TUBE 078329 058381 +FASTENER-SNAP IN 1/4X15/16 073304 SCREW-SHOULDER 4-40X.3755 SOC PART NUMBER ROD-AIR SHUTTER ADJUST DESCRIPTION 1 3 2 2 3 12 4 8 8 54 4 1 1 2 1 6 6 24 4 4 2 3 4 5' 11' 4 4 8 18 3 1 3 2 2 3 12 4 8 8 54 4 1 1 2 1 6 6 24 4 4 2 3 4 5' 11' 4 4 8 18 3 C813 L813 QTY. QTY. 103 103 103 103 103 000 000 000 000 000 000 000 103 103 103 103 103 103 103 103 000 103 103 103 103 000 000 000 103 103 103 103 103 WARR. CLASS COMMENTS Model 811, 813, 819, 821 Series 63 Parts List 078820 021277 058770-2 080610 053995 079622 076222-K 079800-24 073973 073974 073987 073988 R403021 TANK-ACCUMULATOR 10LB-NPT TEE-1/4FPT X 1/4MPT X 1/4FPT TEE-HI TEMP 1/4X1/4 OD TERMINAL-FERRULE 16-22AWG TERMINAL-FERRULE .5MM *M32/3 THERMOCOUPLE-K TYPE SS BRAID THERMOCOUPLE K TRANS.-100VA 120/208/240 PRI TRIM-CORNER *C810* RIGHT FRONT TRIM-CORNER *C810* LEFT FRONT TRIM-CORNER *C810* RIGHT REAR TRIM-CORNER *C810* LEFT REAR TUBE-.170ID X .250OD 073013 WINDOW-FRONT VIEW PORT 075484-CAN 074978 LABEL-FUSE REPLACEMENT 7A 813 073619FC LABEL-ELEC-CAUTION-CANADA X73147-12 CARD-INSTALL-C811 FRENCH- C81323NW79 - 208V 60HZ 3PH - ROHS COMPLIANT *CANADA* WIRE A.-IGNITOR 072985 X51733-C VARISTOR A.-230VAC W/#10 SPADE +GASKET-FRONT VIEW PORT *C 072695-1 VALVE-SOLENOID 3 WAY 12 VDC 072986 072695-4 VALVE-PRESSURE RELIEF 70 PSI +LENS-MICA 079329-02 VALVE-GAS REDUNDANT 3-1/2 WC 1 1 1 3 3 3 3 2 2 1 3 1 1 1 1 3 3 3 3 2 2 1 3 1 000 000 000 103 000 000 103 103 103 103 103 103 103 020959 VALVE-CHECK 1/4MP 2 10' 000 2 078332 10' R403022 VALVE-CHECK W/#69 ORIFICE 103 000 103 103 103 103 103 103 103 000 000 103 000 103 103 103 TUBE-TEFLON .188IDX.250OD 1 10' 1 1 1 1 3 6 4 32 15 1 1 1 2 1 WARR. CLASS 000 1 10' 1 1 1 1 3 6 4 32 15 1 1 1 2 1 C813 L813 QTY. QTY. TUBE-NYLOBRADE 1/4ID X 7/16OD X73640 075780 TUBE A.-GAS BACK *C811* 076989-WP SWITCH-SCREW TERMINAL PART NUMBER SWITCH-ROCKER-DPST-10AMP IP65 DESCRIPTION SEE HOSE COMMENTS Parts List 64 Model 811, 813, 819, 821 Series 076389-CAN 078075-CAN 072658-CAN 073625FCM LABEL-NOTICE-CASTERS-CANADA LABEL-WARN-GAS GRILL-CANADA LABEL-WARN-GRILL-MCD-SVC-CAN MAN-OPER C811/C813 FR-CAN 813 GAGE A.-GAP USA REGULAR X79617 079567-F TOOL 079567 LABEL-INST-LIGHT*15E*FRENCH PART NUMBER LABEL-INST-LIGHT*15E* DESCRIPTION 1 3 1 1 1 1 1 3 1 1 1 1 C813 L813 QTY. QTY. 000 000 000 000 000 000 000 WARR. CLASS COMMENTS 130419 Model 811, 813, 819, 821 Series 65 Parts List PART NUMBER C819 L819 QTY. QTY. WARR. CLASS X72843 X80592 073540 BAR A.-RELEASE MATERIAL BAR A.-RELEASE MATERIAL BAR-BELLY *C820* 072501-SER 078730 077042 080648 072541 080647 076013 072502 073423 073033 051331 073386 076451 X80619 073334 010548 017008 043637 073910 076012 BASE-ADJUSTER 3/8-24 LR/RF BEARING 3/4 ID-SELF ALIGN BEARING-FLANGE 3/4 X 15/16 BEARING-FLANGE 5/8 X 15/1 BEARING .753 X 1.000 X 2.000 BEARING .628 X .813 X 2.000 BLOCK-CONTACT 1 NO BLOCK-GAP ADJUST 3/8-24 BLOCK-TERMINAL 1P BLOCK-TERMINAL 2P .25 SPD-24X BLOCK-TERMINAL 3P 20A, 300V PLATE-TERMINAL BLOCK *C84 BRACKET-PIVOT BULLNOSE A.-*C819* BURNER-I.R. BUSHING-SNAP 11/16 ID X 7/8OD BUSHING-SNAP 1-5/16ID X 1-1/2 BUSHING-SNAP BUSHING-SNAP .391 ID X.500 OD BUTTON-OPERATOR-BLACK 819 072500-SER BASE-ADJUSTER 3/8/-24 LF/RR 079145 X69653 BACKSPLASH A. *C819* +SCREW-3/8-16X1 HEX HEAD CAP 076745 ADAPTOR 000653 052563-2 ADAPTOR-1/4MPT X 1/4 OD TUBE +WASHER-3/8 USS FLAT CR3 079792 ACTUATOR-HOME SWITCH 2 2 3 3 6 2 1 2 1 3 1 1 8 4 4 8 4 4 4 4 4 1 2 1 2 2 2 2 2 3 3 6 2 1 2 1 3 1 1 8 4 4 8 4 4 4 4 4 1 2 1 2 2 2 000 103 103 103 103 103 103 103 103 103 103 103 103 103 000 000 000 000 103 103 103 000 000 103 103 103 103 103 103 103 UPPER CONTROL CONTROL SWITCH C81923NW00 208V 60HZ 3PH & L81923NW00 208V 60HZ 4PH - NATURAL GAS - ROHS COMPLIANT DESCRIPTION REMARKS Parts List 66 Model 811, 813, 819, 821 Series 073240 073160 079777 032129SER2 CASTER-GRILL 5" SWIVEL W/LOCK CLEANER-STERA SHEEN 6 1 QT/CS CLEVIS-ROD 1/2-20 THD COMPRESSOR-AIR-230V SERV 819 030036 X51733-C +VARISTOR A.-230VAC W/#10 SPA +VARISTOR-280VAC RMS 17 MM DIA 020959 +VALVE-CHECK 1/4MP 072695-4 VALVE-PRESSURE RELIEF 70 PSI R403022 072695-1 VALVE-SOLENOID 3 WAY 12 VDC +TUBE-TEFLON .188IDX.250OD 072695-2 REGULATOR-PRESSURE 0-120 PSI 052562 020988 PLUG-1/8 MP-NICKEL PLATED 077879-C 072695-3 GAUGE-130 PSI 1/8 MPT BACK MNT +TEE-1/4OD X 1/4OD X 1/4OD TU 072695-8 +SWITCH-PRESSURE 240V,3HP 072695-6 FITTING-DIFFUSER 1/4 MPT 073129 +MANIFOLD A.-*C832* FITTING-SWIVEL ELBOW 1/4 OD 072695-6 +FITTING-SWIVEL ELBOW 1/4 OD 072695-5 073607 +ELBOW-1/4 X 1/4 TRUE SEAL FITTING-SWIVEL ELBOW 1/4 OD 035573 +ELBOW-1/4PT-STREET-BRASS 077339-M 078377 CASTER-5" 7-5/8 STEM +CROSS-1/4 FPT * 1.562 SQ 073619 CARD-INSTALL-GAS GRILL C811 052563-2 073484 CARD-CHECKOUT GEN MKT INF GAP +ADAPTOR-1/4MPT X 1/4 OD TUBE 069936 X80925 CAN A.-GREASE *C810* HEM 069935 073251 CABLE-PLATEN-F-REAR +SLIDE-GREASE CAN *C810* LEFT 073252 +SLIDE-GREASE CAN *C810* RIGHT 076011 CABLE-PLATEN-FRONT PART NUMBER BUTTON-OPERATOR-RED DESCRIPTION 2 2 1 10' 1 1 1 2 1 1 1 1 1 2 1 1 1 1 1 2 1 2 1 2 2 1 1 1 1 2 4 4 2 2 2 1 10' 1 1 1 2 1 1 1 1 1 2 1 1 1 1 1 2 1 2 1 2 2 1 1 1 1 2 4 4 2 C819 L819 QTY. QTY. 103 103 103 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 212 103 000 103 103 103 103 103 103 103 103 103 000 WARR. CLASS 5/2012 REPLACES X73944 REMARKS Model 811, 813, 819, 821 Series 67 Parts List 073814-23 X73673 080879 032190 077046 070816 079326-12 078329 040140-001 X79256 052560-2 072695-8 065712 079837-070 DIAGRAM-WIRING *C819* DIODE A.-50 PIV 1A ELECTRODE-GAS PILOT E-RING 1/4 BLACK PHOS E-RING-3/4 STEEL E-RING 5/8 EXTERNAL STEEL FAN-BLOWER 60CFM 120/230 VAC FASTENER-SNAP IN 1/4X15/16 FILTER-CORCOM 6EH1 FILTER A.-*M22E* WHT/BLK FITTING-1/4MPTX1/4OD TUBE 90DG FITTING-DIFFUSER 1/4 MPT FORM-QUALITY REPORT BY FAX FUSE-7 AMP MDL-7-R 819 GASKET-BRAIDED-HI TEMP R70113 076299 X69657 DEFLECTOR A.-FLUE *C819* +HOLDER-FUSE-15 A, 250 V 079160 073668 CYLINDER-AIR 6IN STROKE C/C CORD A.-POWER-250V-30A 4 WIRE 072849 +SCREW-SHOULDER 10-32X1/4X.125L 073748 020983 +NUT-10-32 WHIZ FLANGE LOCKNUT COVER-FRONT *C819* X73256 COVER A.-PLATEN *C810* W/RELEASE BAR 068583 X69621-SER CONTROL-MOTOR *C811* COVER A.-USB WATERPROOF X73147-12 +WIRE A.-IGNITOR X80589 X70301-02S COVER A.-PLATEN *C810* 078721 CONTROL-IGNITOR UTC 073471-R CONTROL-LIMIT W/SCREWS 073471-L +HARNESS-HIGH LIMIT C845/C811 070279 PART NUMBER +HARNESS-HIGH LIMIT C845/C811 CONTROL-HI-LIMIT 450F RESET CONTROL-GRILL TOUCH PAD------> DESCRIPTION 10' 1 1 1 1 5 2 2 24 2 8 4 2 2 1 1 2 1 1 2 4 6 2 2 2 2 2 1 1 2 10' 1 1 1 1 5 2 2 24 2 8 4 2 2 1 1 2 1 1 2 2 2 2 2 2 1 1 2 C819 L819 QTY. QTY. 000 103 000 000 103 103 103 103 000 103 000 000 000 103 000 000 103 103 103 103 103 103 103 000 103 212 103 103 103 103 103 103 WARR. CLASS PLATEN *SEE - KIT A.-GRILL CONTROL REMARKS Parts List 68 Model 811, 813, 819, 821 Series 069757 072529 073095 073097 073728 073369 073941 R30317 HARNESS-IGNITION-GROUND *C81 HARNESS-PCB/GR SWITCH *C832* HARNESS-SSR-LEFT*C845* HARNESS-SSR-RIGHT*C845* HARNESS-SWITCH *C820* HARNESS-TOUCH-CONTROL*C810-11* HOSE ASSEMBLY-FLEXIBLE GAS HOSE-BEV.-.250IDX.438OD-100' 074948 X73606 KIT A.-3FT RESTRAIN CABLE KIT A.-ACCESSORY *C820* 819 072673 073106 INSULATION-SHROUD*C845*IN CLIP-RELEASE MATERIAL-W/TAB 079810 INSULATOR-TEFLON-2 HOLE 051742 073429-R +CLAMP-HOSE 7/16-WIRE DICHROMAT 073429-L HARNESS-IDC BOARD 069717 HARNESS-FAN *C819* HARNESS-IDC BOARD 069716 HARNESS-FAN *C819* 073471-R 073608 HARNESS-BLOWER HARNESS-HIGH LIMIT C845/C811 073892 HARNESS A.-MOTOR *C820* 073471-L X73703 HARNESS A.-COMP. VALVE *C812* HARNESS-HIGH LIMIT C845/C811 080588-B 4 1 1 2 4 2 5' 1 2 1 1 1 2 1 1 1 1 1 1 2 2 2 1 1 2 4 2 5' 1 2 1 1 1 2 1 1 1 1 1 1 2 2 2 1 2 000 000 103 000 000 000 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 HANDLE-PLATEN, ELECTROPOL 2 1 073250 1 073440 103 HANDLE-PLATEN 1 1 000 000 GUIDE-PATTY PLACEMENT GEN 1 1 2 000 103 072695-3 GAUGE-130 PSI 1/8 MPT BACK MNT 2 1 000 000 072985 GASKET-FRONT VIEW PORT *C845* 1 1 2 028534-1 073753 GASKET-FRONT SHROUD *C819* 1 2 WARR. CLASS GUARD-FAN 073920 C819 L819 QTY. QTY. GASKET-GORE-TEX 072914 GASKET-FLUE *C819* PART NUMBER GASKET-CONTROL *C842* DESCRIPTION TUBE-NYLOBRADE 1/4ID X 7/16OD CONTROL A.- UPPER CONTROL A.- UPPER *SEE - SEALANT-GORE-TEX 1/4 REMARKS Model 811, 813, 819, 821 Series 69 Parts List 080595 075888 SHEET-RELEASE *L810* STRIP-REPLACEMENT X81328 073625-M X73273-SER LINE A.-GAS-RIGHT *C819* MAN-OPER 811/813/819/821 MOTOR A.-MOUNT *C810* 819 079753 X81327 LINE A.-GAS-LEFT *C819* CLAMP-HANDLE *32/35* 072986 LENS-MICA *C845* 052394 072658 LABEL-WARN GRILL MCD AUTH SVC 079792 079567 LABEL-INST-LIGHT*15E* BUSHING-FLG .627IDX.12W OILI 074978 LABEL-FUSE REPLACEMENT 7A ACTUATOR-HOME SWITCH *32/35* 075484 078329 FASTENER-SNAP IN 1/4X15/16 LABEL-ELEC-CAUTION 078285 X78330-SER 072914 X73474-SER SHIELD-GREASE KIT A.-GREASE SHIELD* +GASKET-CONTROL *C842* KIT A.-GRILL CONTROL-GEN MRKT 000653 001082 SCREW-3/8-16X1 HEX HEAD CAP WASHER-3/8 USS FLAT CR3 024298 X80680 KIT A.-ACCESSORY*LONG PLT 075887 000653 WASHER-3/8 USS FLAT CR3 SCREW-10-32X3/8 SLTD TRUSS 075888 STRIP-REPLACEMENT SCRAPER-TEFLON WIPER 073442 SHEET-RELEASE BOX(9) GEN MRK 080594 001082 SCREW-3/8-16X1 HEX HEAD CAP RETAINER-SHEET RELEASE *L810 024298 SCREW-10-32X3/8 SLTD TRUSS 072673 075887 CLIP-RELEASE MATERIAL-W/TAB 072845 SCRAPER-TEFLON WIPER PART NUMBER RETAINER-SHEET RELEASE *C842 DESCRIPTION 1 2 1 2 1 1 1 2 3 1 1 1 16 4 2 2 2 2 1 1 BX 2 9 1 2 1 1 1 2 3 1 1 1 16 4 2 2 2 2 1 1 2 9 1 3 6 1 C819 L819 QTY. QTY. 103 103 103 103 000 103 103 000 000 000 000 000 000 000 000 000 312 000 000 000 000 000 000 103 000 000 000 000 000 000 000 000 103 WARR. CLASS REMARKS Parts List 70 Model 811, 813, 819, 821 Series 072662 073248-L 073248-R 024351 039536 075985 039508 024195 073249 073764 PULLEY-PLATEN CABLE PULLEY-PLATEN-LEFT PULLEY-PLATEN-RIGHT SCREW-1/4-20X1-1/4 SERR.FLAN SCREW-1/4-20X3/8 SOCKET SET SCREW-10-32X3/8 SERRATED HWH SCREW-4-40X5/8 SLTD ROUND SCREW-8-32X3/8 HEX HEAD CAP SCREW-SHOULDER 5/16 X 1 SWITCH-HOME POSITION 024351 039536 075985 039508 024195 073249 073764 SCREW-1/4-20X1-1/4 SERR.FLAN SCREW-1/4-20X3/8 SOCKET SET SCREW-10-32X3/8 SERRATED HWH SCREW-4-40X5/8 SLTD ROUND SCREW-8-32X3/8 HEX HEAD CAP SCREW-SHOULDER 5/16 X 1 017523 +NUT-1/4-20 WHIZ FLANGE LOCK 819 073249 080603 028534-1 +SCREW-SHOULDER 5/16 X 1 MOTOR-GEAR W/CONN *C810* +GUARD-FAN MOTOR-FAN 95.3 CFM 2700 RPM 4 4 2 1 2 073248-R PULLEY-PLATEN-RIGHT 1 073248-L PULLEY-PLATEN-LEFT 062253-27 072662 PULLEY-PLATEN CABLE SWITCH-HOME POSITION 4 017523 NUT-1/4-20 WHIZ FLANGE LOCK 4 4 2 1 1 4 4 8 6 4 2 2 4 4 2 080603 MOTOR-GEAR W/CONN *C810* 2 4 2 2 079753 052394 BUSHING-FLG .627IDX.12W OILI 1 2 2 2 4 3 2 1 1 2 2 1 C819 L819 QTY. QTY. CLAMP-HANDLE *32/35* 079792 ACTUATOR-HOME SWITCH *32/35* X80578 017523 MOTOR A.-MOUNT *C810* 080603 NUT-1/4-20 WHIZ FLANGE LOCK PART NUMBER MOTOR-GEAR W/CONN *C810* DESCRIPTION 103 103 000 103 103 103 103 000 000 000 000 000 103 103 103 000 103 103 103 103 103 103 103 000 000 000 000 000 103 103 103 000 103 WARR. CLASS GEAR MOTOR USED PRIOR TO M2091954 GEAR MOTOR-X62253-27 TO REPLACE 027309-27 REMARKS Model 811, 813, 819, 821 Series 71 Parts List 010077 027132 053361 050988 072662 073248-L PLUG-HOLE 7/8 DIA. BLACK PLUG-HOLE 1-3/4 DIA. PLUG-HOLE 1-3/8 DIA.-BLACK PLUG-HOLE 3/8 DIA BLACK PLASTI PULLEY-PLATEN CABLE PULLEY-PLATEN-LEFT 819 +SCREW-1/4-20X3/8 SOCKET SET PULLEY-PLATEN-RIGHT 039536 073248-R 039536 073808 PLUG A.-USB CABLE +SCREW-1/4-20X3/8 SOCKET SET X73522-23 PLATEN A.-2600W 208V *C811* 072542 PIN-SPRING UPPER *C842* X73741-23 073992 PANEL-SIDE-LOWER *C810* LEFT 072982 073991 PANEL-SIDE-LOWER *C810* RIGH PLATEN A.-SERVICE *C820* 2600W 073989 PANEL-SIDE UPPER-RT *C810* PLATE-HEAT TRANSFER 073990 PANEL-SIDE UPPER-LT *C810* 073463 X80626 PANEL A.-LIGHT *C819* PLATE-AIR SHUTTER TOP *C845* X69660 PANEL A.-FRONT-LOWER *C819* 079482 X73816 PANEL A.-CONTROL UPPER *C819 079576 X69664 PANEL A.-BACK SERVICE *C819* PLATE-AIR SHUTTER SPACER *M35* 076554-53 ORIFICE-HEX PLUG GAS-#53 PLATE-AIR SHUTTER BOTTOM 076554-40 ORIFICE-HEX PLUG GAS-#40 X79485 073826-005 ORIFICE A.-IGNITOR PLATE A.-AIR SHUTTER SLIDE 073826-003 ORIFICE A.-IGNITOR 080646 052733-118 PIN-SPRING UPPER *C810* 052733-120 O-RING-1-1/16OD X .103W PART NUMBER O-RING-1-3/16OD X .103W DESCRIPTION 2 2 2 2 4 2 1 2 7 2 2 4 2 2 2 2 4 1 1 1 1 1 1 2 1 2 2 2 2 4 8 2 2 2 2 4 2 1 2 7 2 2 6 2 2 2 2 4 1 1 1 1 1 1 2 1 2 2 2 2 4 8 C819 L819 QTY. QTY. 103 103 000 103 000 103 103 103 000 103 212 212 103 103 103 103 103 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 WARR. CLASS UPPER CONTROL MANIFOLD A.-*C842* **NEED SERVICE PART NUMBER REMARKS Parts List 72 Model 811, 813, 819, 821 Series 600136 058381 052010 072849 073249 R700033 R70003 R700032 079952 X73597 072926 SCREW-10-32X3/8 SOCKET SCREW-SHOULDER 4-40X.3755 SOC SCREW-SHOULDER 3/8X3-1/4 SCREW-SHOULDER 10-32X1/4X.125L SCREW-SHOULDER 5/16 X 1 SEALANT-GORE-TEX 1/4 UNCOMP. SEALANT-JOINT 1/2 IN TEADIT SEALANT-JOINT .065 THK X .50 W SEAL-ARM *M32/35* SHIELD A.-HEAT *C811/C845* SHIELD-COUPLING FRONT 072467-1 073729 X73751 X72835 X80585 073749 073750 069936 069935 021625 079074 076657 072617 072542 SHIELD-PLATE TUBE INNER SHIELD-POWER CORD *C820 SHROUD A.-COMBINATION *C819* SHROUD A.-PLATEN *C842* SHROUD A.-PLATEN *C810* SHROUD-OUTER BACK *C811* LEFT SHROUD-OUTER BACK *C811* RIGHT SLIDE-GREASE CAN *C810* L SLIDE-GREASE CAN *C810* R SOCKET-.084 OD/14-20 AWG-STRIP SPACER-HEAT TRANSFER PLATE SPACER-SHROUD SPRING-EXTENSION LATCH *C842* +PIN-SPRING UPPER *C842* 819 072467 078329 SHIELD-PLATE TUBE +FASTENER-SNAP IN 1/4X15/16 078285 073304 ROD-AIR SHUTTER ADJUST *C845* SHIELD-GREASE *M 22* 074210-02 RELAY-SS 25A NON-ALARM 240 VAC 072927 051890-27 SHIELD-COUPLING REAR 072695-2 RELAY-3P-50A 208/240 COIL PART NUMBER REGULATOR-PRESSURE 0-120 PSI DESCRIPTION 4 8 5 36 4 1 1 1 1 2 1 1 4 4 24 4 4 2 2 4 8' 10 12' 4 4 8 12 9 2 4 2 1 5 36 4 1 1 1 1 2 1 1 4 4 24 4 4 2 2 4 8' 10 12' 4 4 8 12 12 2 4 2 1 C819 L819 QTY. QTY. 000 000 000 000 000 103 103 103 103 103 103 103 103 103 103 103 103 000 103 103 000 000 000 000 000 000 103 103 000 103 103 103 103 WARR. CLASS PLATEN SPRING SEE - KIT A.-SHIELD X78330-SER OPERATOR BUTTONS ARM/BACKSPLASH REMARKS Model 811, 813, 819, 821 Series 73 Parts List 073764 SWITCH-HOME POSITION 076989-WP 075780 078820 SWITCH-ROCKER-DPST-10AMP IP65 SWITCH-SCREW TERMINAL TANK-ACCUMULATOR 10LB-NPT 2 073973 073974 073987 073988 X73873 R403021 052560-2 TRIM-CORNER *C810* RIGHT FRONT TRIM-CORNER *C810* LEFT FRONT TRIM-CORNER *C810* RIGHT REAR TRIM-CORNER *C810* LEFT REAR TUBE A.-GAS BACK *C819* TUBE-.170ID X .250OD 076370 077364 +ELBOW-3/8 MPT X 5/16 +FITTING-REDUCER-1/2FPT-3/8FPT 819 081424 +ELBOW-3/8MPT X 3/8MPT STEEL 079329-02 VALVE-GAS REDUNDANT 3-1/2 WC 1 2 2 2 1 1 2 2 2 1 103 103 103 103 103 103 020959 VALVE-CHECK 1/4MP 2 078332 VALVE-CHECK W/#69 ORIFICE M22 2 000 8' 000 8' 103 000 103 103 103 103 103 103 R403022 2 8' 1 1 1 1 1 2 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 000 TUBE-TEFLON .188IDX.250OD 1 1 1 1 1 2 4 4 32 10 1 1 1 2 1 1 2 2 2 2 8 000 WARR. CLASS TUBE-NYLOBRADE 1/4ID X 7/16OD +FITTING-1/4MPTX1/4OD TUBE 8' 079800 TRANS.-100VA 120/208/240 PRI 4 076222-K 4 32 THERMOCOUPLE K 053995 TERMINAL-FERRULE .5MM *M32/3 10 079622 080610 TERMINAL-FERRULE 16-22AWG 1 1 1 2 1 1 2 2 2 2 8 4 8 C819 L819 QTY. QTY. THERMOCOUPLE-K TYPE SS BRAID 052562 TEE-1/4OD X 1/4OD X 1/4OD TUBE 052560-2 077879-C SWITCH-PRESSURE 240V,3HP +FITTING-1/4MPTX1/4OD TUBE 90 074314 SWITCH-PRESSURE 079792 073336 SUPPLY-POWER-10W 12VDC +ACTUATOR-HOME SWITCH *32/35* 040280-020 080646 STANDOFF-NYLON 6-32 SNP/THREAD 080649 +PIN-SPRING UPPER *C810* PART NUMBER SPRING-EXTENSION LATCH *L DESCRIPTION MANIFOLD AIR COMPRESSOR SEE HOSE-BEV.-.250IDX.438OD-100'RL. AIR COMPRESSOR AIR COMPRESSOR LATCH SWITCH COMPRESSOR A.-AIR UPPER CONTROL REMARKS Parts List 74 Model 811, 813, 819, 821 Series 072695-1 X51733-C VALVE-SOLENOID 3 WAY 12 VDC VARISTOR A.-230VAC W/#10 SPADE X73474-SER 073451-M KIT A.-GRILL CONTROL-JIB MAN-OPER 811/819 JACK-IN-BOX 1 2 1 1 1 2 2 2 2 2 2 2 1 2 1 2 2 2 2 2 2 2 1 2 1 C819 L819 QTY. QTY. 075288 X80691-SER 075699SYM3 KIT A.-GRILL CONTROL-WENDYS LABEL-CONTROL PANEL-INTL 073619FC 075484-CAN LABEL-ELEC-CAUTION-CANADA 819 078075-CAN LABEL-WARN-GAS GRILL-CANADA CARD-INSTALL-C811 FRENCH C81923N879 - CANADA X73829 GUARD-LENSE 081411 BIN A.-TOOL STORAGE ROHS COMPLIANT WENDY'S C81923NWWD CORD A.-POWER 4-WIRE NO P 1 1 1 1 1 2 1 C81923NWHF - ROHS COMPLIANT-LESS GAS LINE, LESS ELECTRICAL PLUG X73404 080933-INS 080933 X79617 GAGE A.-GAP *C810-C811* JIB +GUIDE-CHECKOUT JIB GAS CARD-CHECKOUT JIB GAS C81923NWDK - ROHS COMPLIANT-JIB GAGE A.-GAP USA REGULAR TOOL X73147-12 072985 WIRE A.-IGNITOR 072986 +GASKET-FRONT VIEW PORT *C 073013 +LENS-MICA *C845* WINDOW-FRONT VIEW PORT *C845* 030036 072695-4 VALVE-PRESSURE RELIEF 70 PSI +VARISTOR-280VAC RMS 17 MM DIA 079329-02 076343 PART NUMBER VALVE-GAS REDUNDANT 3-1/2 WC +NIPPLE-3/8 MPT CLOSE BLK DESCRIPTION 000 000 000 000 212 103 103 000 000 312 000 000 000 000 103 000 103 000 103 000 103 103 103 103 WARR. CLASS AIR COMPRESSOR REMARKS Model 811, 813, 819, 821 Series 75 Parts List 076389-CAN 072658-CAN 073625FCM LABEL-WARN-GRILL-MCD-SVC MAN-OPER 811/813/819/821 017462 074165 081041-03 073745 073814-75 X78996-40 079803 079837-040 BUSHING-SNAP 5/8ID X 3/4OD-BLK CONTROL-HI-LIMIT 550F NO RE CONTROL-IGNITION 24VAC ROHS CORD-POWER 4MM-5 H07NF 34 DIAGRAM-WIRING *C819* FILTER A.-*M15* WHT/BLK FITTING-.25 BARB W/.030 O FUSE-4 AMP BK/MDL-4-R 2 076343 072695-10 +NIPPLE-3/8 MPT CLOSE BLK 819 LABEL-CONTROL PANEL-INTL 075699SYM3 072569 +SCREW-M3X0.5 3 X79573-36 1 4 2 1 1 2 2 +KIT A.-GAS VALVE 1/2" NPT X81823-SER KIT A.-GAS VALVE 24 VAC 1 +HARNESS A.-GAS VALVE 081781-R HARNESS-MC TO SSR *C819*L 1 1 077364 081781-L HARNESS-MC TO SSR *C819*R +FITTING-REDUCER-1/2FPT-3/ 073422 HARNESS-COMPRESSOR *C845/ 2 078890 081595 HARNESS A.-IGN CNTRL *C84 2 1 +ELBOW-3/8MPTX3/8FPT-BLACK X79573-36 HARNESS A.-GAS VALVE 076370 081780 HARNESS A.-BLOWER *C819* 2 1 1 2 1 1 1 2 2 4 1 1 1 3 1 1 1 2 3 4 2 1 1 2 2 1 1 1 2 2 1 2 1 1 2 1 1 1 2 2 4 1 1 C819 L819 QTY. QTY. +ELBOW-3/8 MPT X 5/16 075288 GUARD-LENSE 076299 068239 BUSHING-3/4"MP X 3/8 FP P +HOLDER-FUSE-15 A, 250 V 051647 BLOCK-TERMINAL 4P 1,2,L1, C81975NW00 400V 50HZ 3N & L81975NW00 400V 50HZ 3N 079567-F LABEL-NOTICE-CASTERS-CANADA PART NUMBER LABEL-INST-LIGHT*15E*FRENCH DESCRIPTION 000 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 000 103 103 000 103 103 103 000 103 103 000 000 000 000 WARR. CLASS REMARKS Parts List 76 Model 811, 813, 819, 821 Series 078075 079538-12 X81744 X81746 076554-51 X81760 X81762 X73741-75 X73522-75 050869-27 052111-03 LABEL-WARN-GAS GRILL LABEL-WIRING *M15E/22E*CO LINE A.-GAS-RIGHT *C819* LINE A.-GAS-LEFT *C819* H ORIFICE-HEX PLUG GAS-#51 PANEL A.-CONTROL UPPER *L819 PANEL A.-CONTROL UPPER *L819 PLATEN A.-SERVICE *C820* 2600W PLATEN A.-2600W 230V *C811* RELAY-4P-40A 200/240 COIL RELAY-DPDT 100UA TO 7A 1/ 059993 TRANS.-CONT.-80VA 230V/24 819 079800-24 050869-27 TRANS.-100VA 120/208/240 PRI RELAY-4P-40A 200/240 COIL 052112 076389 +SOCKET-RELAY-FOR USE W/05 079972 LABEL-NOTICE-CASTERS PART NUMBER LABEL-FUSE REPLACEMENT 4A DESCRIPTION 2 2 1 2 2 1 2 1 1 2 1 1 1 1 1 1 2 2 1 2 2 1 2 1 1 2 1 1 1 1 1 1 C819 L819 QTY. QTY. 103 103 103 103 103 103 212 212 103 103 103 103 103 000 000 000 000 WARR. CLASS REMARKS 130416 Model 811, 813, 819, 821 Series 77 Parts List PART NUMBER C821 L821 QTY. QTY. X72843 BAR A.-RELEASE MATERIAL 080648 072541 080647 078730 076013 073423 073033 051331 X69670 073334 BEARING-FLANGE 5/8 X 15/1 BEARING .753 X 1.000 X 2.000 BEARING .628 X .813 X 2.0 BEARING 3/4 ID-SELF ALIGN BLOCK-CONTACT 1 NO *11/12/15 BLOCK-TERMINAL 1P BLOCK-TERMINAL 2P .25 SPD-24X BLOCK-TERMINAL 3P 20A, 300V BULLNOSE A.-*C819* BURNER-I.R. 010548 027712 017008 BUSHING-SNAP 11/16 ID X 7/8OD BUSHING-SNAP 1-3/8ID X 1-3/4OD BUSHING-SNAP 1-5/16ID X 1-1/2 821 052394 BUSHING-FLG .627IDX.12W OILITE 073016 077042 BEARING-FLANGE 3/4 X 15/16 +BRACKET-BURNER *C845*-SHORT 072501 BASE-ADJUSTER 3/8-24 LR/RF 073010 072500 BASE-ADJUSTER 3/8/-24 LF/RR +BRACKET-BURNER *C845* SIDE 073540 072849 +SCREW-SHOULDER 10-32X1/4X.125L BAR-BELLY *C820* 020983 X80592 +NUT-10-32 WHIZ FLANGE LOCKNUT BAR A.-RELEASE MATERIAL 072849 X69653-R BACKSPLASH A. *C822* +SCREW-SHOULDER 10-32X1/4X.125L 076745 ADAPTOR 020983 052563-2 ADAPTOR-1/4MPT X 1/4 OD TUBE +NUT-10-32 WHIZ FLANGE LOCKNUT 079792 ACTUATOR-HOME SWITCH 3 4 6 2 4 4 2 1 3 1 1 4 2 2 4 2 2 1 2 5 1 1 2 2 1 3 4 6 2 4 4 2 1 3 1 1 4 2 2 4 2 2 1 2 5 1 1 2 2 1 C82123NW39 & L82123NW79 - NATURAL GAS - 1-PLATEN - ROHS COMPLIANT DESCRIPTION 103 103 103 103 103 103 103 103 103 103 103 103 103 000 000 103 000 103 103 103 000 000 103 000 000 103 103 103 103 103 WARR. CLASS REMARKS Parts List 78 Model 811, 813, 819, 821 Series 073252 080587 073240 078377 073160 079777 CABLE-PLATEN-FRONT CABLE-PLATEN-F-REAR *C810 CASTER-GRILL 5" SWIVEL W/LOCK CASTER-5" 7-5/8 STEM CLEANER-STERA SHEEN 6 1 QT/CS CLEVIS-ROD 1/2-20 THD 072695-6 010077 065156-6 077879-C 052562 R403022 020959 +FITTING-SWIVEL ELBOW 1/4 OD +PLUG-HOLE 7/8 DIA. BLACK +PLUG-1/4 NPT-PARKER:VS219P-4 +SWITCH-PRESSURE 240V,3HP +TEE-1/4OD X 1/4OD X 1/4OD TUBE +TUBE-TEFLON .188IDX.250OD +VALVE-CHECK 1/4MP X70301-02S 078721 X69621-SER 073668 CONTROL-IGNITOR UTC *M35* CONTROL-LIMIT W/SCREWS CONTROL-MOTOR *C811* CORD A.-POWER-250V-30A 4 WIRE 821 070279 +GASKET-CONTROL CONTROL-HI-LIMIT 450F RESET 072914 077339-M +CROSS-1/4 FPT * 1.562 SQ CONTROL-GRILL TOUCH PAD------> 052563-2 +ADAPTOR-1/4MPT X 1/4 OD TUBE 032129SER2 073251 CABLE-PLATEN-F-REAR COMPRESSOR-AIR-230V SERV 073619 CARD-INSTALL-GAS GRILL C8 072673 073484 CARD-CHECKOUT GEN MKT INF GAP CLIP-RELEASE MATERIAL-W/TAB 069936 X80925 CAN A.-GREASE *C810* HEM 069935 076011 BUTTON-OPERATOR-RED +SLIDE-GREASE CAN *C810* L 076012 +SLIDE-GREASE CAN *C810* R 073910 BUTTON-OPERATOR-BLACK PART NUMBER BUSHING-SNAP .391 ID X.500 OD DESCRIPTION 1 2 1 2 2 2 1 5' 1 1 1 1 1 1 2 1 4 1 2 2 2 2 1 1 1 1 2 2 2 2 1 2 1 2 2 2 1 5' 1 1 1 1 1 1 2 1 4 1 2 2 2 2 1 1 1 1 2 2 2 2 C821 L821 QTY. QTY. 103 212 103 103 103 000 103 000 103 103 103 000 103 103 103 212 000 000 000 103 103 103 103 103 000 000 103 103 103 103 103 103 WARR. CLASS SEE KIT A.-GRILL CONTROL - X73474-SER SAMPLE SENT WITH NEW EQUIPMENT 5-2012 REPLACES X73944 REMARKS Model 811, 813, 819, 821 Series 79 Parts List 073250 080588-B X73703-R HANDLE-PLATEN HANDLE-PLATEN, ELECTROPOL HARNESS A.-COMP. VALVE *C820 821 073440 1 1 1 1 1 1 2 103 103 103 103 000 000 GUIDE-PATTY PLACEMENT GEN MKT 2 1 072985 GASKET-FRONT VIEW PORT *C845* 1 073753 GASKET-FRONT SHROUD *C819* 000 000 2 10 103 103 000 2 10 1 000 000 103 103 103 103 103 103 000 103 000 000 000 000 103 103 103 103 103 103 103 103 072914 R70113 GASKET-BRAIDED-HI TEMP 1 1 1 1 1 2 2 5 2 1 24 1 4 4 1 1 1 1 1 2 1 1 WARR. CLASS GASKET-CONTROL *C842* 072695-3 GAUGE-130 PSI 1/8 MPT BACK MNT 1 1 1 1 2 2 5 2 1 24 1 4 4 1 1 1 1 1 2 1 1 C821 L821 QTY. QTY. GASKET-GORE-TEX .250 DIA 076299 +HOLDER-FUSE-15 A, 250 V 079837-070 X79256 FILTER A.-*M22E* WHT/BLK 065712 078329 FASTENER-SNAP IN 1/4X15/16 FUSE-7 AMP MDQ-7 079326-12 FAN-BLOWER 60CFM 120/230 VAC FORM-QUALITY REPORT BY FAX 070816 E-RING 5/8 EXTERNAL STEEL 072695-8 077046 E-RING-3/4 STEEL FITTING-DIFFUSER 1/4 MPT 032190 E-RING 1/4 BLACK PHOS 072695-6 069842-23 DIAGRAM-WIRING *C821* 073911 X69657 DEFLECTOR A.-FLUE *C819* FITTING-SWIVEL ELBOW 1/4 OD TB 079160 CYLINDER-AIR 6IN STROKE C/C FITTING-5/16X5/16X3/16 COMP 077339-M CROSS-1/4 FPT * 1.562 SQ 052560-2 073748 COVER-FRONT *C819* FITTING-1/4MPTX1/4OD TUBE 90DG 068583 COVER A.-USB WATERPROOF 040140-001 X80589 COVER A.-PLATEN *C810* FILTER-CORCOM 6EH1 X73256 073729 PART NUMBER COVER A.-PLATEN *C810* +SHIELD-POWER CORD *C820* DESCRIPTION SEE SEALANT-GORE TEX R700033 1/17/12 REPLACES 073809 REMARKS Parts List 80 Model 811, 813, 819, 821 Series 073429-L 073429-R 069757 072529 073731 073095 073728 073369 076299 HARNESS-IDC BOARD HARNESS-IDC BOARD HARNESS-IGNITION-GROUND * HARNESS-PCB/GR SWITCH *C832* HARNESS-RHT-GAS-DETECT *C HARNESS-SSR-LEFT*C845* HARNESS-SWITCH HARNESS-TOUCH-CONTROL HOLDER-FUSE-15 A, 250 V 075887 024298 001082 073442 075888 000653 X80680 SCRAPER-TEFLON WIPER SCREW-10-32X3/8 SLTD TRUSS SCREW-3/8-16X1 HEX HEAD CAP SHEET-RELEASE BOX(9) GEN MRK STRIP-REPLACEMENT WASHER-3/8 USS FLAT CR3 KIT A.-ACCESSORY*LONG PLT 821 072673 072845 RETAINER-SHEET RELEASE CLIP-RELEASE MATERIAL-W/TAB 072673 X73606 KIT A.-ACCESSORY *C820* CLIP-RELEASE MATERIAL-W/TAB 074948 2 1 1 2 9 1 2 4 1 1 2 X73147-12 KIT A.-3FT RESTRAIN CABLE +WIRE A.-IGNITOR *C845* 2 073826-005 +ORIFICE A.-IGNITOR 2 073826-003 2 5' 1 1 2 1 1 1 2 1 1 1 1 1 1 1 2 2 6 1 1 2 2 2 2 5' 1 1 2 1 1 1 2 1 1 1 1 1 1 1 2 2 C821 L821 QTY. QTY. +ORIFICE A.-IGNITOR 073812 073471-R HARNESS-HIGH LIMIT C845/C811 IGNITOR-SPARK 073471-L HARNESS-HIGH LIMIT C845/C811 R30317 069717 HARNESS-FAN *C819* HOSE-BEV.-.250IDX.438OD-100' 069716 HARNESS-FAN *C819* 073941 073608 HOSE ASSEMBLY-FLEXIBLE GAS 073892 HARNESS-BLOWER PART NUMBER HARNESS A.-MOTOR *C820* DESCRIPTION 000 000 000 000 000 000 000 000 103 000 000 103 103 103 103 103 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 WARR. CLASS NATURAL GAS LP GAS REMARKS Model 811, 813, 819, 821 Series 81 Parts List 024298 001082 080595 075888 000653 SCREW-10-32X3/8 SLTD TRUSS SCREW-3/8-16X1 HEX HEAD CAP SHEET-RELEASE *L810* STRIP-REPLACEMENT WASHER-3/8 USS FLAT CR3 072986 LENS-MICA *C845* 821 073249 072695-1 VALVE-SOLENOID 3 WAY 12 VDC +SCREW-SHOULDER 5/16 X 1 072695-4 VALVE-PRESSURE RELIEF 70 PSI 073247 072695-2 REGULATOR-PRESSURE 0-120 PSI 062253-27 072695-3 GAUGE-130 PSI 1/8 MPT BACK M MOTOR-GEAR *M32/35* STEPPER V3 072695-6 FITTING-SWIVEL ELBOW 1/4 OD MOTOR-FAN 95.3 CFM 2700 RPM 072695-5 FITTING-SWIVEL ELBOW 1/4 OD 073129-R MANIFOLD A.-*C822* 072695-8 073946FCM MAN-OPER C819 FRENCH CANADIA FITTING-DIFFUSER 1/4 MPT 073946-M MAN-OPER C819 072985 072658-CAN LABEL-WARN-GRILL-MCD-SVC-CAN +GASKET-FRONT VIEW PORT *C845* 078075-CAN LABEL-WARN-GAS GRILL-CANA 079567-F LABEL-INST-LIGHT*15E*FREN 076389-CAN 079567 LABEL-INST-LIGHT*15E* LABEL-NOTICE-CASTERS-CANADA 075484-CAN 072914 LABEL-ELEC-CAUTION-CANADA +GASKET-CONTROL X73474-SER 078329 FASTENER-SNAP IN 1/4X15/16 KIT A.-GRILL CONTROL-GEN MRKT 078285 SHIELD-GREASE *M 22* X78330-SER 075887 KIT A.-GREASE SHIELD* 080594 SCRAPER-TEFLON WIPER PART NUMBER RETAINER-SHEET RELEASE *L810 DESCRIPTION 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 3 1 1 1 1 1 2 2 24 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 3 1 1 1 1 1 2 2 24 2 1 2 1 1 2 9 1 3 C821 L821 QTY. QTY. 103 103 103 103 103 103 103 103 103 103 103 000 000 000 000 000 000 000 000 000 000 000 312 000 103 000 000 000 000 000 000 000 103 WARR. CLASS COMPLETE ASSY - X73273-SER MOTOR A.-MT REMARKS Parts List 82 Model 811, 813, 819, 821 Series 053361 050988 072662 073248-L 073248-R 072695-2 074210-02 051890-27 072845 PLUG-HOLE 1-3/8 DIA.-BLACK PLUG-HOLE 3/8 DIA BLACK PLASTI PULLEY-PLATEN CABLE PULLEY-PLATEN-LEFT PULLEY-PLATEN-RIGHT REGULATOR-PRESSURE 0-120 PSI RELAY-SS 25A NON-ALARM 240 V RELAY-3P-50A 208/240 COIL RETAINER-SHEET RELEASE (RETENTION BAR) 821 072673 027132 PLUG-HOLE 1-3/4 DIA. +CLIP-RELEASE MATERIAL-W/TAB 010077 080646 PIN-SPRING UPPER *C810* 073808 072542 PIN-SPRING UPPER *C842* PLUG-HOLE 7/8 DIA. BLACK 073990 PANEL-SIDE UPPER-LT *C810* PLUG A.-USB CABLE 073989 PANEL-SIDE UPPER-RT *C810* X73522-23 073992 PANEL-SIDE-LOWER *C810* LEFT PLATEN A.-2600W 208V *C811* 073991 PANEL-SIDE-LOWER *C810* RIGH X73741-23 X80626 PANEL A.-LIGHT *C819* X73570 X69660 PANEL A.-FRONT-LOWER *C81 PLATEN A.-SERVICE *C820* 2600W X69664 PANEL A.-BACK SERVICE *C8 PLATE A.-DOOR HINGE-R 076554-53 ORIFICE-HEX PLUG GAS-#53 X73569 076554-40 ORIFICE-HEX PLUG GAS-#40 PLATE A.-DOOR HINGE-L 073826-005 ORIFICE A.-IGNITOR X79485 073826-003 ORIFICE A.-IGNITOR PLATE A.-AIR SHUTTER SLIDE 052733-120 017523 PART NUMBER O-RING-1-3/16OD X .103W +NUT-1/4-20 WHIZ FLANGE LOCK DESCRIPTION 4 2 1 2 1 1 1 2 2 1 2 6 2 1 1 1 2 2 1 1 1 1 1 1 1 2 2 2 2 4 2 4 2 1 2 1 1 1 2 2 1 2 6 2 1 1 1 2 2 1 1 1 1 1 1 1 2 2 2 2 4 2 C821 L821 QTY. QTY. 103 000 103 103 103 103 103 103 103 000 000 000 103 212 212 103 103 103 000 000 103 103 103 103 103 103 103 103 103 103 103 000 103 WARR. CLASS LP GAS NATURAL GAS NATURAL GAS LP GAS REMARKS Model 811, 813, 819, 821 Series 83 Parts List X73597 072926 072927 078285 SHIELD A.-HEAT *C811/C845* SHIELD-COUPLING FRONT SHIELD-COUPLING REAR SHIELD-GREASE *M 22* 072466 072467 072467-1 073729 X73751 SHIELD-PLATE SHROUD-OUTER SHIELD-PLATE TUBE SHIELD-PLATE TUBE INNER SHIELD-POWER CORD *C820* SHROUD A.-COMBINATION *C819* 821 072465 SHIELD-PLATE SHROUD 078329 073442 SHEET-RELEASE BOX(9) GEN MRK +FASTENER-SNAP IN 1/4X15/16 079952 SEAL-ARM *M32/35* 058381 SCREW-SHOULDER 4-40X.3755 SOC R70003 009894 SCREW-8X1/4 SLTD HEX WASHER SEALANT-JOINT 1/2 IN TEADIT 041363 SCREW-6-32X5/8 UNSLTD HWH R700033 002201 SCREW-6-32X3/8 SLTD BINDER 073249 015582 SCREW-10X3/8 SLOTTED HEX WSHR SEALANT-GORE-TEX 1/4 UNCOMP. 039381 SCREW-10-32X3/8 UNSL HWH SERR SCREW-SHOULDER 5/16 X 1 024298 SCREW-10-32X3/8 SLTD TRUSS 072849 037734 SCREW-10-32X1/2 SLTD TRUSS SCREW-SHOULDER 10-32X1/4X.125L 020982 SCREW-10-32X1/2 SERRATED HWH 052010 002077 SCREW-10-24X1/2 TORX TRUSS T20 SCREW-SHOULDER 3/8X3-1/4 017522 SCREW-1/4-20X5/8 SERRATED HWH 075888 +STRIP-REPLACEMENT 011694 075887 SCREW-1/4-20X3/8 SLTD ROUND 073304 SCRAPER-TEFLON WIPER PART NUMBER ROD-AIR SHUTTER ADJUST *C845* DESCRIPTION 1 1 3 3 3 3 24 2 2 1 2 1 2 5 6' 2 2 4 12 4 12 4 36 16 22 10 14 4 17 30 1 1 2 1 1 3 3 3 3 24 2 2 1 2 1 2 5 6' 2 2 4 12 4 12 4 36 16 22 10 14 4 17 30 1 1 2 C821 L821 QTY. QTY. 103 000 103 103 103 103 000 103 103 103 103 000 000 000 000 103 103 103 000 000 000 000 000 000 000 000 000 000 000 000 000 000 103 WARR. CLASS SEE - KIT A.-GREASE SHIELD X78330-SER REMARKS Parts List 84 Model 811, 813, 819, 821 Series 078820 052562 076222-K 079622 079800 073973 073974 073987 073988 X73873 R403021 020568-20 020568-24 TANK-ACCUMULATOR 10LB-NPT TEE-1/4OD X 1/4OD X 1/4OD TUBE THERMOCOUPLE K *M 15* THERMOCOUPLE-K TYPE SS BRAID TRANS.-100VA 120/208/240 PRI TRIM-CORNER *C810* FRONT-RIGHT TRIM-CORNER *C810* FRONT-LEFT TRIM-CORNER *C810* REAR-RIGHT TRIM-CORNER *C810* REAR-LEFT TUBE A.-GAS BACK *C819* TUBE-.170ID X .250OD TUBE-NYLOBRADE 1/4ID X 7/16O TUBE-NYLOBRADE 1/4ID X 7/16O 078332 VALVE-CHECK W/#69 ORIFICE 821 R403022 TUBE-TEFLON .188IDX.250OD 051742 075780 SWITCH-SCREW TERMINAL +CLAMP-HOSE 7/16-WIRE DICHROMAT 076989-WP 074314 SWITCH-PRESSURE SWITCH-ROCKER-DPST-10AMP IP65 077879-C 079792 073764 SWITCH-PRESSURE 240V,3HP +ACTUATOR-HOME SWITCH *32/35* SWITCH-HOME POSITION 075780 X73775 SWITCH A.-LATCH *C820* SWITCH-SCREW TERMINAL 073336 072542 +PIN-SPRING UPPER 080646 072617 SPRING-EXTENSION LATCH SUPPLY-POWER-10W 12VDC 069936 SLIDE-GREASE CAN *C810* L PIN-SPRING UPPER *C810* 069935 SLIDE-GREASE CAN *C810* R 080649 X80585 SPRING-EXTENSION LATCH *L X72835 SHROUD A.-PLATEN *C810* PART NUMBER SHROUD A.-PLATEN DESCRIPTION 1 6' 2 1 1 7' 1 1 1 1 1 2 2 4 1 1 2 1 2 1 1 1 2 2 2 2 4 1 1 1 1 6' 2 1 1 7' 1 1 1 1 1 2 2 4 1 1 2 1 2 1 1 1 2 2 2 2 4 1 1 1 C821 L821 QTY. QTY. 103 000 000 000 000 000 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 103 000 000 000 000 103 103 103 103 WARR. CLASS REMARKS Model 811, 813, 819, 821 Series 85 Parts List 821 X73147-12 072985 WIRE A.-IGNITOR +GASKET-FRONT VIEW PORT *C 073013 WINDOW-FRONT VIEW PORT *C845* 072986 X51733-C VARISTOR A.-230VAC W/#10 SPADE +LENS-MICA *C845* 072695-1 VALVE-SOLENOID 3 WAY 12 VDC 077364 FITTING-REDUCER-1/2FPT-3/8FP 072695-4 078890 ELBOW-3/8MPTX3/8FPT-BLACK VALVE-PRESSURE RELIEF 70 PSI 076370 079329-02 ELBOW-3/8 MPT X 5/16 020959 VALVE-GAS REDUNDANT 3-1/2 WC PART NUMBER VALVE-CHECK 1/4MP DESCRIPTION 2 2 2 2 2 1 1 1 1 2 2 1 2 2 2 2 2 1 1 1 1 2 2 1 C821 L821 QTY. QTY. 103 000 000 103 103 103 103 103 103 103 103 103 WARR. CLASS REMARKS 811 073475-23 8/12 811 073475-75 3/13 813 073725-23 9/12 819 073814-23 7/12 819 073814-75 3/13 821 069842-23 7/12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Print high-res Author : t165411 Create Date : 2013:04:19 16:09:32-05:00 Modify Date : 2013:05:15 10:28:03-04:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2013:05:15 10:28:03-04:00 Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : opCvr Creator : t165411 Document ID : uuid:345a63e4-1907-466a-9a76-8cdac1cd0544 Instance ID : uuid:5b25056f-61ce-4af9-aa5d-fc64f3689cc8 Producer : Acrobat Distiller 8.3.1 (Windows) Page Count : 95EXIF Metadata provided by EXIF.tools