Technisonic TDFM-136A VHF/FM Digital Airborne Transceiver User Manual 1
Technisonic Industries Limited VHF/FM Digital Airborne Transceiver 1
Contents
- 1. User Manual 1
- 2. User Manual 2
User Manual 1
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1193891 |
| Application ID | ++aW6N741GF77gQ1r7O0Iw== |
| Document Description | User Manual 1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 56.25kB (703120 bits) |
| Date Submitted | 2009-11-04 00:00:00 |
| Date Available | 2009-11-04 00:00:00 |
| Creation Date | 2009-09-24 14:59:42 |
| Producing Software | Acrobat Distiller 8.1.0 (Windows) |
| Document Lastmod | 2009-09-24 14:59:42 |
| Document Title | Microsoft Word - 09re404C1 TDFM-136A Install Instructions.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | danthuynh |
VHF/FM DIGITAL AIRBORNE TRANSCEIVER MODEL TDFM-136A Installation Instructions TiL Document No. 09re404 Revision C Issue 1 JUNE 2009 Technisonic Industries Limited 240 Traders Boulevard, Mississauga, Ontario L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 www.til.ca REVISIONS for 09re404 Sections 1 – 2 REV SECTION - PAGE - Table 1-1 - STC Approv. - Table 1-5 - FCC Compliance - FCC Compliance - Table 1-4 - 2.5 Antenna Installation. - Footer, all pages. 2.5 2-5 DESCRIPTION DATE Changed operating temp to –30 to +60 C. Change references of DO-160C to 160D. Change Temp & Alt to B4 and D1. Change Magnetic Effect to class Z. Add FCC RF Exposure Requirements warning. May 26/09 Change separation distance from 110cm to 1.0m. Change RF Output Power Low to read “1W”. June 15/09 Change 0dB to 3dBi and 20cm (8 inches) to 1.0m (40 inches). Remove “and Operating” from “Installation and Operating Instructions”. Change antenna supplier & part number to Comant Industries Inc. / Part No. CI 292-3 Fig 2-3 Wiring Connections (added ITEM 4) Jun 26/09 Aug 12/09 This page left intentionally blank. TECHNISONIC INDUSTRIES LIMITED www.til.ca ESD CAUTION This unit contains static sensitive devices. Wear a grounded wrist strap and/or conductive gloves when handling printed circuit boards. FCC COMPLIANCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: For compliance with FCC RF Exposure Requirements, the mobile transmitter antenna installation shall comply with the following conditions: 1. 2. The transmitter antenna gain shall not exceed 3 dBi. The transmitter antenna is required to be located outside of a vehicle and kept at a separation distance of 1.0 meter or more between the transmitter antenna of this device and persons during operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Re-orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet or circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by Technisonic Industries could void the user’s authority to operate the equipment. WARRANTY INFORMATION The Model TDFM-136A transceiver is under warranty for one year from date of purchase. Failed units caused by defective parts, or workmanship should be returned to: Technisonic Industries Limited 240 Traders Boulevard Mississauga, Ontario L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 NOTICE: The above stated address supersedes all others that may appear otherwise in this manual. TECHNISONIC INDUSTRIES LIMITED www.til.ca STC APPROVAL NOTE Presently, no TSO standard exists for airborne FM transceivers. To make it easier for installation agencies to provide their customers with an approved installation supported by an effective Airworthiness Approval, Technisonic has secured Supplemental Type Certificate (STC) Approvals (both US and Canadian) on its Airborne FM products for many helicopters currently being delivered in the US and Canada as well as a number of single engine fixed wing aircraft. The above referenced DO-160D test data is also on file and available from Technisonic to support approval requirements in airframes for which Technisonic does not possess an STC. Approved aircraft types are listed in the attachments to the formal STC documents. These STCs are the exclusive property of Technisonic and require the written authority of Technisonic for their use. To assist Factory Authorized Technisonic Dealers in the certification process, we have placed copies of our Canadian and US STCs on our web site along with a letter of authorization for their use. These documents may be downloaded and used as support for the technical submission to FAA or Transport Canada. Only authorized factory dealers/installers are permitted to download and make use of these documents on behalf of their customers (end users) in support of regulatory agency approval. Please refer to the Technisonic web site www.til.ca for the latest issue of available STCs and letter of authorization for use. COPYRIGHT NOTICE This document contains designs and other information which are the property of Technisonic Industries Ltd. Except for rights expressly granted by contract to the Canadian Government, or to the United States Government, this document may not, in whole or in part, be duplicated or disclosed or used for manufacture of the part disclosed herein, without the prior permission of Technisonic Industries Ltd. WARNING AND DISCLAIMER This manual is designed to provide information about the TDFM-136A. Every effort has been made to make this manual as complete and accurate as possible. TECHNISONIC INDUSTRIES LIMITED www.til.ca TABLE OF CONTENTS SECTION TITLE Table of Contents ............................................................................................................................. List of Figures ................................................................................................................................... List of Tables .................................................................................................................................... SECTION 1 1.1 1.2 1.3 1.4 1.5 1.6 vi vi GENERAL DESCRIPTION Introduction ....................................................................................................................... Description ........................................................................................................................ Purpose of Equipment ...................................................................................................... Model Variation ................................................................................................................. Technical Characteristics ................................................................................................ Certification Summary ...................................................................................................... SECTION 2 PAGE 1-1 1-1 1-1 1-2 1-2 1-5 OPERATING INSTRUCTIONS General ............................................................................................................................... Equipment Packing Log ................................................................................................... Transceiver Installation .................................................................................................... Installation Kit – Contents ................................................................................................ Antenna Installation .......................................................................................................... Installation - Pin Locations and Connections ................................................................ Wiring Instructions ........................................................................................................... 2-7.1 Main Power +28VDC .................................................................................................... 2-7.2 Main Ground ................................................................................................................. 2-7.3 PTT (Ground Keying) ................................................................................................... 2-7.4 Front Panel Back Lighting ............................................................................................ 2-7.5 Audio Outputs (600 ohms and 4 0hms) ....................................................................... 2-7.6 Audio Output Ground ................................................................................................... 2-7.7 Mic Signal Input ............................................................................................................ 2-7.8 Memory Up/Memory Down .......................................................................................... 2-7.9 Data Input/Output ......................................................................................................... 2.8 Transmitter Side Tone Level Adjustment ....................................................................... 2.9 Main and Guard Noise Squelch Adjustment .................................................................. 2.10 Reference Layouts ............................................................................................................ 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2-1 2-1 2-1 2-1 2-1 2-2 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-6 2-6 2-7 APPENDICES APPENDIX A Post Installation EMI Test Instructions....................................................................... PURPOSE ................................................................................................................................ TEST CONDITIONS ................................................................................................................. METHODOLOGY ...................................................................................................................... RESULTS ................................................................................................................................. PROCEDURE ........................................................................................................................... TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 A-1 A-1 A-1 A-1 A-1 A-2 Page v TECHNISONIC INDUSTRIES LIMITED www.til.ca LIST OF FIGURES FIGURE 2-1 2-2 2-3 2-4 TITLE Transceiver Mounted View of the 15-Pin Connector .......................................................... Outline Drawing for TDFM-136A Transceiver ..................................................................... Wiring Connections for TDFM-136A Transceiver ............................................................... Control points for the TDFM-136A MCU Board .................................................................. PAGE 2-2 2-3 2-5 2-7 LIST OF TABLES TABLE TITLE PAGE 1-1 1-2 1-3 1-4 1-5 TDFM-136A – General Characteristics ............................................................................... TDFM-136A – Operational Characteristics ......................................................................... TDFM-136A – Receiver Characteristics – Main and Guard ............................................... TDFM-136A – Transmitter Characteristics ......................................................................... TDFM-136A – Environmental Testing Summary ................................................................ 1-3 1-4 1-4 1-5 1-5 2-1 TDFM-136A - Rear Connector Pin Assignments ................................................................ 2-2 TDFM-136A Installation Instructions TiL 09RE404 Rev C issue 1 Page vi TECHNISONIC INDUSTRIES LIMITED www.til.ca SECTION 1 - GENERAL DESCRIPTION 1.1 INTRODUCTION This publication provides operating and installation information for the TDFM-136A, Digital Transceiver manufactured by Technisonic Industries Limited. The TDFM-136A is Project 25 (P25), Phase 1 compliant. The unit offers digital or conventional analog FM communications over an extended frequency range with selectable channel spacing and is intended for use (in the U.S.) only by government agencies or contractors thereto, who have obtained licensing for operation in the 136-150 MHz portion of the band. If the TDFM-136A transceiver is used in CANADA, operation is restricted to the following sub bands: 138-144, 148-148.99, 149.005150.005 and 150.05-174 MHz. Furthermore the frequency agile transceiver is restricted to airborne use and must not be operated as a base station in Canada. 1.2 DESCRIPTION The TDFM-136A, Transceiver is a frequency agile, fully synthesized airborne transceiver capable of operating in the 136.000 MHz to 174.000 MHz frequency range in 2.5 kHz increments with either 25 kHz analog, 12.5 kHz analog channel spacing and P25, 12.5 kHz digital modulation on a channel by channel basis. The Transceiver can operate without restriction on any split frequency pair in the band and also incorporates a two channel synthesized guard receiver. The TDFM-136A Transceiver provides 230 operator accessible memory positions. Each of which is capable of storing Scan List membership information, up to eight (8) character alphanumeric identifier, and Operating Mode information. In addition each memory position contains information for both transmit and receive including: frequency, CTCSS tone, DCS (DPL) code, P25 TalkGroup, and P25 Network Access Code (NAC) information. Channel operating parameters, including frequency and other related data, are presented on a 48-character, two-line LED matrix display. Data entry and function control takes place via a 12button keypad. 1.3 PURPOSE OF EQUIPMENT The TDFM-136A, Digital VHF/FM Transceiver is designed to provide secondary airborne communications to facilitate operations which are typically performed in a low altitude environment. The transmitter section of this unit has a minimum of 8 watts and does not exceed 10 watts output power, which may be reduced by a front panel switch to 1 watt, in order to reduce interference to land based systems. TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 1-1 TECHNISONIC INDUSTRIES LIMITED www.til.ca 1.4 MODEL VARIATION There are twelve variations of the Model TDFM-136A Transceiver. features and performance except for the following differences: TDFM-136A, P/N 091258-1-10 TDFM-136A, P/N 091258-1-11 TDFM-136A, P/N 091258-2-10 TDFM-136A, P/N 091258-2-11 TDFM-136A, P/N 091258-3-10 TDFM-136A, P/N 091258-3-11 TDFM-136A, P/N 091258-4-10 TDFM-136A, P/N 091258-4-11 TDFM-136A, P/N 091258-5-10 TDFM-136A, P/N 091258-5-11 TDFM-136A, P/N 091258-6-10 TDFM-136A, P/N 091258-6-11 TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 All units offer identical GREEN display 28v back lighting, no Encryption. GREEN display 28v back lighting, with Encryption. RED display 28v back lighting, no Encryption. RED display 28v back lighting, with Encryption. NV display 28v back lighting, no Encryption. NV display 28v back lighting, with Encryption. GREEN display 5v back lighting, no Encryption. GREEN display 5v back lighting, with Encryption. RED display 5v back lighting, no Encryption. RED display 5v back lighting, with Encryption. NV display 5v back lighting, no Encryption. NV display 5v back lighting, with Encryption. Page 1-2 TECHNISONIC INDUSTRIES LIMITED www.til.ca 1.5 TECHNICAL CHARACTERISTICS The tables below provide the technical characteristics for the Technisonic Industries Ltd. Model TDFM-136A. TABLE 1-1 TDFM-136A – General Characteristics Characteristic Specification Dimensions (including heat sink) Approx. 8.0" X 3.0" X 5.75" Weight Approx. 3.5 Lbs (1.6 Kg) Mounting Panel Mount via DZUS fasteners Power Requirement: Voltage Current Audio Output Power: Headset Speaker Output 28.0 VDC, ±15% Receive - 0.7 A Max. Transmit Low Power (1W) - 1.3 A Max. Transmit High Power (8-10W) - 2.0 A Max. 0.5 Watts into 600 ohms 2.5 Watts min. into 4 ohms Back Lighting 28 Volts (standard) 5 Volts (specify) Display Colour Green (standard) Red (specify) NVG (optional) Temperature Range: Operating Storage Altitude TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 -30ºC to +60ºC -55ºC to +85ºC 50,000 feet Page 1-3 TECHNISONIC INDUSTRIES LIMITED www.til.ca TABLE 1-2 TDFM-136A – Operational Characteristics Characteristic Specification Frequency Range: 136.000 to 174.000 MHz Operating Modes: Conventional analog: 12.5 / 25 kHz. P25 CAI: 12 KBPS FSK, 9.6 KBPS C4FM 25 kHz. or 12.5 kHz Channel Spacing: Programmable Memories: Scan Lists Description Operating Modes Frequency Squelch Modes CTCSS Tones 230 memories 15 scan lists Up to 8 characters, alpha-numeric Analog Wide, Analog Narrow, P25 Digital Rx/Tx (Simplex/Duplex), 136.0000 – 174.0000 Rx/Tx (Simplex/Duplex), CTCSS Tones, DCS Codes, P25 TalkGroup, P25 NAC 2 channels programmed with: Up to 8 characters, alpha-numeric Analog Wide, Analog Narrow, Digital Rx/Tx (Simplex/Duplex), 136.0000 – 174.0000 MHz. Rx/Tx (Simplex/Duplex), CTCSS Tones, DCS Codes, P25 TalkGroup, P25 NAC 42 CTCSS tones, including all standard tones. DCS Codes All standard DCS (DPL1) codes P25 TalkGroup $0000 to $FFFF ( 0 to 65535 ) P25 Network Access Code (NAC) $000 to $FFF ( 0 to 4095 ) Guard Receiver: Description Operating Modes Frequency Squelch Modes DPL is a trademark of Motorola Corporation TABLE 1-3 TDFM-136A – Receiver Characteristics – Main and Guard Characteristic Specification Sensitivity at 12 dB SINAD -116dBm Adjacent Channel Selectivity -60dB (25 or 12.5 kHz) Spurious Attenuation -70 dB Third Order Intermodulation -70 dB Image Attenuation -80 dB FM Acceptance ± 6 kHz Hum and Noise better than 45dB Audio Distortion less than 5% Antenna Conducted Emission less than -57dBm TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 1-4 TECHNISONIC INDUSTRIES LIMITED www.til.ca TABLE 1-4 TDFM-136A – Transmitter Characteristics Characteristic RF Output Power: Low High Output Impedance 1W. 10W. 50 ohms Maximum Deviation: Wide (25 kHz) Narrow (12.5 kHz) Maximum Deviation – Narrow ± 5 kHz ± 2.5 kHz ± 2.5 kHz (12.5 kHz mode) Spurious Attenuation -90 dB below carrier level Frequency Stability ± 2.5 ppm Microphone Circuit Carbon or equivalent Sidetone Output 0.5W (max) into 600 ohms Harmonic Attenuation -65 dB below carrier level FM Hum And Noise -40 dB Audio Input 50 mV at 2.5 into 200 Ω input circuit for ± 3.5 deviation, adjust. Less than 5% Audio Distortion 1.6 Specification CERTIFICATION SUMMARY The following table gives a summary of DO-160D Environmental Testing for Technisonic Model TDFM-136A, VHF Digital Transceiver. TABLE 1-5 TDFM-136A – Environmental Testing Summary Conditions Section Description of Conducted Tests Temperature and Altitude 4.0 Equipment tested to categories B4 and D1. Temperature Variation 5.0 Category B. Humidity 6.0 Category A. Operational Shock and Crash Safety 7.0 Category A. Vibration 8.0 Magnetic Effect 15.0 Equipment is tested without shock mounts to categories S and U. Equipment is class Z. Power Input 16.0 Category B. Voltage Spike 17.0 Category B. Audio Frequency Susceptibility 18.0 Category B. Induced Signal Susceptibility 19.0 Category A. Radio Frequency Susceptibility 20.0 Category U. RF Emission (DO-160D) RF Emission (DO-160C) Electrostatic Discharge 21.0 Category B. Category Z. Category A. TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 25.0 Page 1-5 TECHNISONIC INDUSTRIES LIMITED www.til.ca This page left intentionally blank. TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 1-6 TECHNISONIC INDUSTRIES LIMITED www.til.ca SECTION 2 – INSTALLATION INSTRUCTIONS 2.1 GENERAL This section contains information and instructions for the correct installation of the TDFM-136A, VHF/FM Digital Transceiver. Make certain that the correct frequencies are pre-programmed in accordance with the equipment user's valid FCC operator's license, prior to installation. 2.2 EQUIPMENT PACKING LOG Unpack the equipment and check for any damage that may have occurred during transit. Save the original shipping container for returns due to damage or warranty claims. Check that each item on the packing slip has been shipped in the container. Verify that the equipment display and back-lighting configuration are the same as those ordered. 2.3 TRANSCEIVER INSTALLATION The TDFM-136A Transceivers are designed to be Dzus mounted and should be installed in conjunction with an IN-150 installation kit. See Figure 2-1 for an outline drawing of the unit with dimensions to facilitate the installation. 2.4 INSTALLATION KIT - CONTENTS The IN-150 installation kit consists of: 1. One 15-pin (female) Cannon D-mating connector complete with crimp pins and hoods. 2. One BNC antenna mating RF connector (male) and hood. 2.5 ANTENNA INSTALLATION Antenna, P/N CI 292-3 may be obtained from Comant Industries Inc. or a suitable equivalent 3dBi gain antenna may be used with the TDFM-136A transceivers. The antenna should be mounted on the bottom of the aircraft whenever possible and must be located at least 1.0 meter (40 inches) from any occupant in the airframe. Consult with instructions provided with the antenna. Connect RF cable from antenna to the back of the TDFM-136A unit by utilizing the BNC mating connector provided in the installation kit. 2.6 INSTALLATION - PIN LOCATIONS AND CONNECTIONS A single 15-pin DSUB connector, mounted on the rear of the unit, provides the means to connect all power, control and audio signals between the TDFM-136A and the airframe. The pin numbers and locations for the 15-pin DSUB connector are shown in figure 2-1 below. The view shown is of the connector mounted in the unit, select mating connector appropriately. FIGURE 2.1 Transceiver mounted view of 15-pin male connector TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 2-1 TECHNISONIC INDUSTRIES LIMITED www.til.ca Table 2-1 provides the description of the pin connections for the transceiver. TABLE 2-1 TDFM-136A - Rear Connector Pin Assignments Pin # Description Notes Audio - Headset Output – 600 Ohms Serial Data Out Output – RS232 Power - Panel Lighting 28 VDC Standard, 5VDC Optional Signal - Memory Up Input – active low Signal - Memory Down Input – active low Audio - Microphone Input 7,14 Power - Main +28VDC Power 8,15 Power - Main Ground Power Audio - Speaker 4-Ohm Speaker Output 10 Signal Ground 4-Ohm / 600-Ohm Output Ground 11 Serial Data In Input – RS232 13 Signal – PTT Input – active low TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 2-2 TECHNISONIC INDUSTRIES LIMITED www.til.ca (All dimensions in inches) FIGURE 2-2 Outline Drawing for Model TDFM-136A Transceiver TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 2-3 TECHNISONIC INDUSTRIES LIMITED www.til.ca 2.7 WIRING INSTRUCTIONS – 15-PIN D-CONNECTOR Figure 2-3 shows all required connections and recommended wire sizes for the TDFM-136A Transceiver operation in the airframe. 2.7.1 Main Power +28 VDC The main power +28VDC (± 15%) is connected to pins 7 and 14 of the 15-pin D-connector on the transceiver. Both pins should be connected. 2.7.2 Main Ground Ground connections for the transceiver are made on pins 8 and 15. Both pins should be connected. 2.7.3 PTT (Ground Keying) The PTT line is connected to pin 13 and should be floating when the transceiver is in receive mode, and grounded during transmit mode. 2.7.4 Front Panel Back Lighting Front panel back lighting connection should be made on pin 3 of the transceiver. The opposite end of this lead should be connected to the panel lighting system of the aircraft. Before connecting, verify the required panel lighting voltage (28 VDC or 5 VAC) on the transceiver configuration control label. 2.7.5 Audio Outputs (600 Ohms and 4 Ohms) The audio output from pin 9 can be used to drive a 4 ohm speaker up to 2.5 watts. Audio output from pin 1 is 600 Ohms, 0.5 watts maximum. 2.7.6 Audio Output Ground Pin 10 is the ground for both the 4 and 600 Ohms audio output signals on pins 9 and 1. 2.7.7 Mic Signal Input The microphone input signal is to be provided on pin 6, utilizing shielded wire with the shield grounded to pin 10. 2.7.8 Memory Up/Memory Down Remote scrolling through the 25 memory positions can be achieved by providing a ground to pins 4 (up) and 5 (down) through a momentary contact cyclic switch. 2.7.9 Data Input Channel data may be transferred to and from the unit using RS-232 communications protocol via pins 2 and 11. TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 2-4 TECHNISONIC INDUSTRIES LIMITED www.til.ca Figure 2-3 Wiring Connections for TDFM-136A Transceiver TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 2-5 TECHNISONIC INDUSTRIES LIMITED www.til.ca 2.8 TRANSMITTER SIDE TONE LEVEL ADJUSTMENT The side tone level is set at the factory; however, this level can be altered to suit local conditions as follows: 1. Set the transceiver operating frequency to 155.000 MHz and connect an appropriate test receiver to the RF output connector. Ensure that the output of the transceiver is terminated into a proper dummy load. 2. Key the transmitter and input a 1 kHz audio signal @ -10 dBm (0.25 VRMS) into the microphone input. 3. Select the side-tone adjust command (L2-7) and then adjust the side-tone level using the up/down arrows (keys 2 & 8) to produce a +3.0 dBm (1.0 VRMS) 600 Ohm audio output. 2.9 MAIN AND GUARD NOISE SQUELCH ADJUSTMENT The squelch (on both the main and guard receivers) is factory set to open at approximately 0.5 micro-volts. This adjustment can be altered to suit local conditions as follows: 1. 2. 3. 4. 2.10 Set the main receiver of the transceiver to 155.000 MHz. Connect a signal generator to the antenna input of the transceiver. Set the signal generator to produce a ± 3 deviation with a 1 kHz tone on 156.000 MHz. Increase the signal generator RF level from 0.1 uV until the squelch indicator LED is on. Verify the receiver SINAD ratio is between 12 and 14 dB. If not, re-adjust main receiver squelch via the main receiver squelch software command. Repeat the above procedure to adjust the guard receiver squelch setting using guard receiver squelch adjustment software command. REFERENCE LAYOUTS A reference layout indicating the position of control points for the MCU board is shown in Figure 2-4. TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 2-6 TECHNISONIC INDUSTRIES LIMITED www.til.ca J2: J4: Boot Program Enable - factory set DO NOT INSTALL Option Jumpers: 1-2 Maintenance Mode Enable - DO NOT INSTALL IN AIRFRAME, BENCH ONLY 2-4 Factory Use Only – DO NOT INSTALL 5-6 n/u reserved R8: R10: R11: R17: R18: R56: Main Rx Audio adjust - factory set Tx Mic Audio Level Adjust – factory set Guard Rx Audio adjust – factory set RF Low power adjust – factory set RF High power adjust – factory set DTMF Level Adjust – factory set FIGURE 2-4 Control points for the TDFM-136A MCU Board TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 2-7 TECHNISONIC INDUSTRIES LIMITED www.til.ca This page left intentionally blank TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page 2-8 TECHNISONIC INDUSTRIES LIMITED www.til.ca APPENDIX A – POST INSTALLATION EMI TEST INSTRUCTIONS” PURPOSE The purpose of these tests is to identify any interference that the TDFM-136A may cause with existing aircraft systems. TEST CONDITIONS The TDFM-136A transceiver should be installed and function tested. The antenna VSWR should be checked. A forward/reverse power check with an in-line wattmeter should show no more than 10% reflected power. For the following tests, insure that the power switch is in the high position. METHODOLOGY Most of the EMI tests can be accomplished on the ground. In some cases flight testing is required or is easier. If the aircraft is approved for IFR operations, then it is mandatory that interference between the TDFM-136A Airborne FM and the approach aids be checked in flight. The GPS should be operational and navigating with at least the minimum compliment of satellites. The VHF COMM should be set to the frequencies indicated with the squelch open. VOR/DME receivers should be set to the frequencies indicated and selected for display. If possible, set up a DME ramp test set on the frequencies indicated and adjust the output until the flags are out of view. The transponder and encoder should be monitored with ramp test equipment. Set the output of the transponder test set to 3db above the output necessary to achieve 90% reply. If possible set the ADF to a nearby navigation station. Modulate the TDFM-136A transmitter on the indicated frequencies for at least 20 seconds. Observe the GPS for any degradation in satellite status or availability or flags. Listen for any noise or detected audio signals on the VHF COMM(s). Listen for any noise or detected audio signals on the VOR/LOC receiver audio; look for any movement of flags or needles on the VOR/LOC/GS navigation display(s). Observe the transponder for any loss of reply or spurious reply. List the power plant, fuel and other electric instruments in the chart provided and note any anomalies that occur while transmitting. Assess the results. If the aircraft is equipped with an auto-pilot or a stability augmentation system, then test fly the aircraft and verify that operation of the TDFM-136A transceiver does not have adverse effects on these systems. After checking for gross effects at a safe altitude, fly an approach with each of the different navigation systems coupled to the auto-pilot (ILS, GPS etc.) and look for any anomalies. RESULTS If the installed system passes all of the applicable EMI tests, then no further action is required. If interference is observed, then the interference must be assessed against the appropriate standards of airworthiness for the system in question. For example, it is permissible for a VFR certified GPS to lose navigation capability while the TDFM-136A is transmitting providing that it recovers properly and promptly, but is not permissible for an IFR approach certified GPS to be affected in the same way. A complete discussion of all the standards of airworthiness to be applied in assessing EMI effects is beyond the scope of this document. TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page A-1 TECHNISONIC INDUSTRIES LIMITED www.til.ca PROCEDURE A. Operate the TDFM-136A transmitter on the following frequency for at least 20 seconds. Observe the GPS for any degradation in satellite status or availability or flags. FREQUENCIES TDFM-136A GPS #1 PASS GPS #2 FAIL PASS FAIL 143.1800 MHz 143.1825 MHz 157.5000 MHz 157.5425 MHz NOTES: TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page A-2 TECHNISONIC INDUSTRIES LIMITED www.til.ca B. Determine if the image frequency for the VHF COMM falls within the range of the TDFM-136A. If so, select a set of frequencies that will cause the TDFM-136A to be set as close as possible to the image frequency. Any one of the many possible sets will suffice. Record those values in the spaces provided in the following chart. Modulate the TDFM-136A transmitter on the following frequencies for at least 20 seconds. Listen for any noise or detected audio signals on the VHF Comm. EXAMPLE: Bendix/King KY 196A. The first IF frequency is 11.4 MHz. The LO is above the receive frequency (high side injection). Therefore, the image frequency is 22.8 MHz above the selected frequency. Set the KY 196A to 120.000 MHz and the TDFM-136A to 142.8000 MHz. FREQUENCIES VHF #1 TDFM-136A 135.975 MHz 135.975 MHz 121.150 MHz 121.150 MHz 131.250 MHz 131.250 MHz RESULTS PASS FAIL Image FREQUENCIES VHF #2 TDFM-136A 138.0000 MHz 138.0000 MHz 157.5000 MHz 157.5000 MHz 157.5000 MHz 157.5000 MHz RESULTS PASS FAIL Image NOTES: TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page A-3 TECHNISONIC INDUSTRIES LIMITED www.til.ca C. Determine if the image frequency for the VOR/ILS Nav falls within the range of the TDFM-136A. If so, select two sets of frequencies that will cause the TDFM-136A to be set a close as possible to the image frequency. Chose one set in the localizer frequency range and one in the VOR frequency range. Record those values in the spaces provided in the following chart. Modulate the TDFM-136A transmitter on the following frequencies for at least 20 seconds. Listen for any noise or detected audio signals on the receiver audio; look for any moment of flags or needles on the navigation display. FREQUENCIES VOR / ILS #1 TDFM-136A 108.000 MHz 162.0000 MHz 108.100 MHz 162.1500 MHz RESULTS PASS FAIL Image Image FREQUENCIES VOR / ILS #2 TDFM-136A 108.000 MHz 162.0000 MHz 108.100 MHz 162.1500 MHz RESULTS PASS FAIL Image Image NOTES: TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page A-4 TECHNISONIC INDUSTRIES LIMITED www.til.ca D. Modulate the TDFM-136A transmitter on the following frequencies for at least 20 seconds. Observe the Glide Slope displays. Look for any movement of flags or needles on the Navigation display. FREQUENCIES Glide slope #1 334.7 (108.1) TDFM-136A PASS FAIL 167.3500 MHz FREQUENCIES Glide slope #2 334.7 (108.1) RESULTS TDFM-136A RESULTS PASS FAIL 167.3500 MHz NOTES: TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page A-5 TECHNISONIC INDUSTRIES LIMITED www.til.ca For the following tests (E & F), select a frequency at the top, middle and bottom of the band of the TDFM-136A Transceiver. VHF Band (138 to 174 MHz) Frequency No. 1 Frequency No. 2 Frequency No. 3 E. At a safe altitude engage the autopilot or stability augmentation system. Modulate the TDFM136A on the above frequencies for at least 20 seconds. Observe any effect on the autopilot or stability augmentation system. Observations: F. Perform a coupled ILS approach to the aircraft’s certified limits. Modulate the TDFM-136A transmitter on the above frequencies for at least 20 seconds. Observe any effect on the autopilot. Repeat for second flight director/autopilot if so equipped. Observations: TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page A-6 TECHNISONIC INDUSTRIES LIMITED www.til.ca G. List the power plant, fuel and other electric instruments in the chart provided and note any anomalies that occur while transmitting. Assess the results. STEP SYSTEM COMM 1 and 2 Transponder and Encoder ADF 1 and 2 Vertical Gyro Glide slope 1 and 2 VOR/LOC 1 and 2 Directional Gyro Compass Fuel Pressure 10 Oil Temperature 11 Ammeter 12 Bus Voltage 13 Fuel 14 Nt 15 TOT 16 % Torque 17 Digital Clock 18 Oil Pressure 19 Annunciators TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 PASS FAIL NOTES Page A-7 TECHNISONIC INDUSTRIES LIMITED www.til.ca STEP SYSTEM PASS FAIL NOTES NOTES: TDFM-136A Installation Instructions TiL 09RE404 Rev C Issue 1 Page A-8
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Format : application/pdf Creator : danthuynh Title : Microsoft Word - 09re404C1 TDFM-136A Install Instructions.doc Create Date : 2009:09:24 14:59:42-04:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2009:09:24 14:59:42-04:00 Producer : Acrobat Distiller 8.1.0 (Windows) Document ID : uuid:442ea3f4-6b4b-490b-a86c-ecaa0b6eb84a Instance ID : uuid:d958a54b-d421-49d0-9929-a23d5589f5cf Page Count : 31 Author : danthuynhEXIF Metadata provided by EXIF.tools