Tekk D-150 DMR Digital Radio User Manual DP 150 English manual

Download:
Mirror Download [FCC.gov]
Document ID	4010018
Application ID	5Ro0/sejpx4Ytg+nVBN5Jw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	36.92kB (461520 bits)
Date Submitted	2018-09-18 00:00:00
Date Available	2018-09-18 00:00:00
Creation Date	2018-09-06 16:40:02
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2018-09-18 11:34:50
Document Title	Microsoft Word - DP-150 English manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	xm07095

For user
For optimum performance from this product.please read this
manual and the supplied Safety Information Booklet carefully
before use.
Do not use this radio or charge the battery in an explosive
environment, such as gas, dust, smoke, etc.Do not leave the radio
in a dusty or wet environment. It is very important for the user to
understand all instructions before using the radio
ATTENTION
Please read the following brief instructions, non‐compliance with these instructions
may cause danger or be unlawful.
1.Obey the government regulation before using this radio, improper operation may
violate the law.
2.Do not use in explosive areas.
3.Do not charge or change the battery inexplosive areas.
4.Do not use the radio with a damaged antenna,touching a damaged antenna will
cause heat injury.
5.Do not attempt to open the radio: the maintenance work must be done by
technical experts only.
6.To avoid troubles caused by electromagnetic interference or electromagnetic
compatibility, please turn off the radio in places where signed: Using radio
equipment close to electronic equipment can cause it to malfunction.
7.In a car with a safety airbag, do not put the radio within the scope of the airbag.
8.Do not place the radio under the direct sunlight or very hot locations.
9.When transmittingkeep antenna away from internal body parts.
10. If you smell burning, please switch off radio’s power immediately and contact
your local supplier.
UNPACKING AND DEVICE CHECKING
Thank you for purchasing the TeKK digital handheld transceiver.
Before using:
1.Please check whether the packing box is damaged..
2.Please unpack packing box carefully,and confirm the following list of
items are in the box.If any items are missing or have been damaged
during shipment,please contact radio supplier
immediately.
Supplied Accessories
ITEM
QTY
Antenna
Li‐ion Battery
Power Adapter
Charger
Belt Clip
Strap
Manual
Charger
Note：
The pictures above are for reference only.
BATTERY INFORMATION
Charging Li‐ion Battery
Please charge the battery before using.Charge‐discharge cycle two times
can make the battery capacity achieve better performance.When the
battery power is low,please recharge the battery or replace with a spare
battery.
Applicable Battery Type
Please use Liberty designated battery as any other battery may cause
explosion.
The procedure of charging:
Use only the designated charger and battery,the LED on charger can
indicate the charging stage.
 Charge Diagram
 Procedures
1.Connect the power adapter to AC socket,”1”.
2.Plug the power adapter into the rear jack of the charger,”2”.
3.Place the radio with the battery attached,into the charger,“3”
LED Indicator
Status
Red
Charging
Green
Fully charged
Warning:
For safety the lithium battery is not chargedbefore shipment.
1 When charging, it is better to turn off the radio..
○
2 Charge battery by desktop charger or USB plug.
○
3 While charging,the indicator light will turn red.
○
4 It needs at least4 to 5 hours to charge the battery fully.Whencharging
○
is completed,the indicator light will turn green.
 If charging the battery for a long time, it will shorten the service life of the
lithium battery. When the battery is full, please stop charging.
 the charger is only for this model radio.
 The battery should be placed in a cool, dry place after full charge. Do not expose
to heat source or exposure to the sun.
 You can not transmit while charging.
 The battery will heat upwhile charging,this is a normalphenomenon.
CARE AND CLEANING
To guarantee optimal performance as well as a long service life of
the product.please follow the tips below.
Product Care




Do not pierce of scrape the product with any sharp instruments.
Keep the product far away from substances that can corrode the circuit.
Do not hold the product by its antenna or earpiece cable directly.
Attach the accessory jack cover when the product is not in use.
Product Cleaning
 Clean up the radio and charger with a clean and dry lint-free cloth.
 Use neutral cleanser and a non-woven fabric to clean the
keys,control,knobs and front case after long-time use. Do not use
chemicals such as stain removers, alcohol,sprays or oil preparations, to
avoid surface case damage.Make sure the product is completely dry
before use.
Caution: Power off and remove the battery before cleaning.
PREPARATION BEFORE USING
Assembling the antenna
Turn the antenna clockwise to fasten it.
Assembling the battery
1.Slide the battery into the radio`s slot.
2.To remove the battery,turn off the radio.Press release button and slide
the battery latch upward to release the battery.
Install belt clip
Slide the belt clip into the slot until it clicks.
Be familiar with the radio
Schematic diagram of the whole radio
Side key function:
No set ; Volume + ; Volume - ; Analog monitor ; Scan ; VOX ; Repeater/Talkaround ;
High/Low power ; Turn on/off screen display.
BASIC OPERATIONS
Turning the radio on/off
In the shut down status, long press the red power button until a click is
heard to turn the radio on/off.
Adjusting thevolume
After the radio is powered on, press [side key 1] to increase the volume,
press [side key 2] to decrease the volume, a total of 10 levels to
choose,level 0 is turn off the communication voice.
Transmitting / Receiving
To transmit audio signals,press and hold down the [PTT] button,and
speak into the microphone.During transmission,the LED glows red.
To receive,just release the [PTT] button.When any audio signal is
received,the LED glows green.
Note:
1.To ensure optimal volume of the receiving radio,hold the radio approximately 2.5 to 5
centimeters away from your mouth.
2.Communication range may get affected in rainy days or forest locations.
Monitor(Analog)
This feature allows you to lower the conditions for incoming signal
match.
Long press [side key 1] 2 seconds,and than you can monitor the current
channel signal, the status of the light is green. It will exit the monitor
status after released the [side key 1] .
Selecting a channel
Push up[channel selection key]to choose more lower channel,and push
down to choose more higher channel.Or long press down to choose the
channel rapidly.
Note:
When the radio is currently on a blank channel,it will sound beep tones continuously.
Keyboard lock
Long press[channel selection key]2 seconds, the device prompts the
beep sound and keyboard will be locked, the screen will display "
". At
the same time, the device can not switch the channel and adjust the
volume. Then press [channel selection key] 2 seconds to unlock keyboard
lock.
Scan
This feature allows you to listen to communication activities on other
channels so that you can keep a close track of your team members.The
scan list can be set by your dealer.
1.In boot status, press [side key 2] 2 seconds to enter channel scan mode,
screen displays [SCAN] and voice prompt "scan". While in scanning mode,
the device will detect the received signals of each channel, and it will
stop scan until the signal is found.
2.When the device is scanned into an active signal, the device will remain
on the current channel until the signal disappears.The scan status will be
recovered after signal disappeared 5 seconds.
3.In scan status,press [side key 2] 2 seconds again to exit the scan mode,
screen display [SCAN] will disappearwhile voice prompts "scan off".
Note: You can not enter the scan mode until at least 2 active
channels have been stored.
Low batteryalert
This features allows you to know the low battery status.When battery
power lower than 25±5,the LED will flash red,and the tone “Please
charge the battery”will sound periodically.In this case,please replace or
charge the battery.
1.When the battery voltage is 0, the device will shutdownautomatically
to protect the radio . And limit the user to boot.please replace the new
battery or charge the battery.
2.When the operating voltage of the device is higher than 4.5V, the
machine will automatically shutdown to protect the radio , and limit the
user to boot. Please pay attention to the normal operating voltage range
of the equipment: 3.5V ~ 4.2V.
Battery strength indicator
This features allows you to know the current battery strength.
Double press the red power button,it will display the percentage of
battery strength.
FUNCTION SETTING(by programming software)
Squelch level settings
This radio provide 0‐9 grade level to select, Users need to make
reasonable settings according to the actual operation environment.The
higher the grade is, the higher the strength of the communication signal
need.Please do not set arbitrarily , so as not to affect the effective
communication distance.
Note:
0 level is equal to close the squelch level setting, device will always open
the receiving channel.The factory setting is level 5.
Transmit power level settings
Equipment provide high/low power for user to choose, please select and
set according to the actual using environment.
Voice reporting number settings
This radio provide Chinese/English and no number reporting,please
select and set according to the actual using environment.
Time‐outtimer (TOT)
The purpose of TOT is to prevent any user from occupying a channel for
an extended period.This function will limit the transmit time,when it
exceed setting time,radio will stop transmit and keep beeping.To stop
beeping,You can Press [PTT] again to resume the transmit status.This
radio provide 15‐600 seconds for user reference in analog channel.And
provide 30‐270 seconds in digital channel.
Programming procedure:
“Channel”→”More”→“TX Setting ”→“Time‐out timer(s)”
Transmit authority settings
When the current channel is in a receive state, if the launch permission
function is set, the device will limit the transmitting operation according
to the set trigger condition,mean while if user press [PTT] key,radio will
prompt a alarm then back to receive state.
Programming procedure:
“Channel”→”More”→“TX Setting ”→“Tx authority”→”Admit
criteria/Channel free”
Note:
In digital channel,”In call criteria” settings will determine whether to activate emission limits.
Battery save
In standby mode,when no signal is received/transmitted or no operation
(key press) is performed for 10 seconds(can programming by
software),the radio will automatically enter battery save mode to reduce
power consumption.The radio may exit the battery save mode and get
activated as soon as any key is pressed or any signal is received.
Users can turn on/off the battery save function by software. Specific
start up time and power saving mode, please select according to the
specific use environment.
Suggestion: it is recommended to turn on the power‐saving function,
and the power‐saving mode is best within the "1:2"! If you set up too
higher will resulting in delay the call, but can reduce the standby power
consumption. Please select according to the specific use environment.
VOX settings
This feature allows you to transmit your voice with no need to press the
[PTT].However,you must employ a dedicated earpiece to realize the
function.
1.User can turn on/off the VOX function by program software.User also
can set the side key function into “ VOX”,then you can turn on the VOX
by press side key.After turn on this function,the screen will display
“VOX”.
2.It has 9 levels for users to choose,among them, level 1 is the highest
sensitivity, level 9 is the lowest.If you turn on VOX function,please turn
off the launch end prompt if without use external headset.
Screen display and settings
Display function can be turned on/off by program software.The screen
display time can be set by program software.User also can set the side
key function into “Display”,then you can turn on/off the screen display by
press side key.After exceed the setting time, the screen display will turn
off automatically.
Read/Write frequency password settings
The device has read and write frequency encryption settings. When the
option is opened, please keep the password in mind Otherwise, if you
forget the password, you will not be able to communicate with the
device by programming software!
The initial password for the software is: 000000. Users can change into
any valid password which are containing 6 digits.
Digital relay function settings
This setting will valid when the digital channel`s TX/RX frequency is
different.
Users
can
set
the
frequency
of
repeater
by
press
“Channel”→”More”,then making tick at “relay” to turn on relay
function.You can also customize the side key function for quick
operation.
After turn on the relay function,can set the number of repeated
transmissions when the device is accessing the relay by press “Basic
Setting”→”Setting”→”Relay Retransmission”.The recommended value is
not less than 5 times, and the user can adjust the settings according to
the use environment.
Note:This device supports digital channel which is not require access to the repeater then
can be realized in one channel with different frequency under the condition of direct call. If the
user is in different state,if not open "relay" function, the equipment will continue to maintain a
normal digital communication mode.
Digital communication function settings
1.Contacts
The device provides 64 digital contact to setting.
When adding a contact person, the software will configure an ID to
the user by default. The user can also define the ID number of the
current contact person within the range of 0‐16776415. The ID number
of this contact corresponds to the ID number of the device you want to
call,
and
the
machine
ID
number
is
set
in
"Basic
Setting"→"Setting"→"Serial No."→"Machine number".
The "call type" determines the call mode of the current contact, and
the device provides three options: "group call", "single call" and "all call".
The user can set according to the specific situation. In "all call" mode, the
ID will be set by the device, the user does not need to define their own.
In the digital channel,Press”more”→"Contacts No.",can set the
corresponding call. If you set the "contacts No." to: “none”, the device
will not be able to transmit signal.
2.RX Group Lists
The device supports up to 32 contact lists, and the user can uses the
right mouse button to click the "RX Group Lists" menu for editing.
3.Digital channel communication encryption function
The device provides 10 groups with a length of 10 hexadecimal (0 ~ f)
password set. Do not set the password too close, at least to ensure that
more than five characters are different.
In the digital channel,Press”more”→"Encryption"can select whether
to activate, and the specific “Encryption Key No.” In the case of
activation, only the password is consistent, the device can receive the
signal normally.
QT and DQT selective
This device provide QT*39 and DQT*83 for user reference.Please setting
by program software.
QT code
62.5Hz
11
91.5Hz
21
127.3Hz
31
167.9Hz
41
199.5Hz
67.0Hz
12
94.8Hz
22
131.8Hz
32
171.3Hz
42
203.5Hz
69.3Hz
13
97.4Hz
23
136.5Hz
33
173.8Hz
43
206.5Hz
71.9Hz
14
100.0Hz
24
141.3Hz
34
177.3Hz
44
210.7Hz
74.4Hz
15
103.5Hz
25
146.2Hz
35
179.9Hz
45
218.1Hz
77.0Hz
16
107.2Hz
26
151.4Hz
36
183.5Hz
46
225.7Hz
79.7Hz
17
110.9Hz
27
156.7Hz
37
186.2Hz
47
229.1Hz
82.5Hz
18
114.8Hz
28
159.8Hz
38
189.9Hz
48
233.6Hz
85.4Hz
19
118.8Hz
29
162.2Hz
39
192.8Hz
49
241.8Hz
10
88.5Hz
20
123.0Hz
30
165.5Hz
40
196.6Hz
50
250.3Hz
51
254.1Hz
DQT code
D023N
17
D116N
33
D243N
49
D365N
65
D546N
81
D734N
D025N
18
D125N
34
D244N
50
D371N
66
D565N
82
D743N
D026N
19
D131N
35
D245N
51
D411N
67
D606N
83
D754N
D031N
20
D132N
36
D251N
52
D412N
68
D612N
D032N
21
D134N
37
D261N
53
D413N
69
D624N
D043N
22
D143N
38
D263N
54
D423N
70
D627N
D047N
23
D152N
39
D265N
55
D431N
71
D631N
D051N
24
D155N
40
D271N
56
D432N
72
D632N
D054N
25
D156N
41
D306N
57
D445N
73
D654N
10
D065N
26
D162N
42
D311N
58
D464N
74
D662N
11
D071N
27
D165N
43
D315N
59
D465N
75
D664N
12
D072N
28
D172N
44
D331N
60
D466N
76
D703N
13
D073N
29
D174N
45
D343N
61
D503N
77
D712N
14
D074N
30
D205N
46
D346N
62
D506N
78
D723N
15
D114N
31
D223N
47
D351N
63
D516N
79
D731N
16
D115N
32
D226N
48
D364N
64
D532N
80
D732N
Troubleshooting
Phenomena
The radio can
not be powered
on.
Analysis
Solution
The battery may be improperly
installed.
Remove the battery and attach
it again.
Clean the battery contacts.If
the problem can not be
solved,contact your dealer or
our authorized service center
for inspection and repair.
Recharge or replace the
battery.
The battery may suffer from
poor contact caused by dirtied
or damaged battery contacts.
The battery may run out.
The battery strength may too
low.
During receiving
signals,the voice
is
weak,discontinu
ous or totally
inactive.
You can not
communicate
with other
members.
Recharge or replace the
battery.
The volume may be set to a low Increase the volume by press
lever.
the [+] button.
The antenna may get loose or
may be improperly installed.
Power off the radio,re‐install
the antenna and power on the
radio again.
The speaker may be blocked or
damaged.
Clean surface of the speaker.If
the problem can not be
solved,contact your dealer or
our authorized service center
for inspection and repair.
The frequency or signaling may
be inconsistent with that of
other members.
Set your TX/RX frequency and
signaling to the same as that of
other members.
You may be too far away from
the group members.
Move towards other
members.And make sure that
you are within the
communication range.
Irrelevant
communication
activities or
noises are heard
on the channel.
The noise is too
loud.
You may be interrupted by
radios using the same
frequency.
Change the frequency,or adjust
the squelch level.
The radio may set with no
signaling.
Set signaling for all member
radios to avoid interference at
the same frequency.
You may be too far away from
other members.
Move towards other
members.And make sure that
you are within the
communication range.
You may be at an unfavorable
position.For example,your
Move to an open and flat
communication may be blocked
area,and restart the radio.
by high buildings or frustrated
in the underground areas.
You may suffer from external
disturbance (such as
electromagnetic interference).
Stay away from equipment that
may cause interference.
Note:
If the above solutions can not fix your problems,or you may have some
other queries,please contact us or your local dealer for more technical
support.
TECHNICAL SPECIFICATIONS
GENERAL
Frequency range
136-174 MHz
Channel capacity
128 channel
(Share by digital and analog mode)
Working voltage
DC 3.7V
Antenna impedance
50Ω
Frequency Stability
±2.5ppm
Working current of whole machine
TX: ≤ 1.4A
Low power：0.7A
RX：≤ 0.7A
Standby: ≤ 0.1A
Working mode
The same frequency simplex
/Different frequency simplex
Battery Capacity
Working temperature
Weight
1500mAh
-30~+60 ℃
155g (not contain antenna&belt
clip)
Dimension(L*W*H)
90mm*61mm*30mm (not contain
antenna&belt clip)
Transmitter
Output power
Rated high power:2.0W
Rated low power:0. 5W
Analog :FM
Modulation mode
Digital:4FSK
Modulation error rate
≤ 5%
Modulation deviation
≤ 2.5KHz（N）
Spurious radiation
≤ 7.5uW
Adjacent channel power
≤ ‐60dB（N）
Receiver
Analog RF sensitivity(12dB SINAD)
≤ 0.25uV/12.5KHz
Digital RF sensitivity
0.22uV（BER 5%）
Audio distortion
≤ 10%
Audio power
1W
Clutter suppression
≥ 65dB
Note:The above parameters are subject to change without prior notice!
Guarantee
Model Number:
Serial Number:
Purchase Date:
Dealer:
Telephone:
User`s Name:
Telephone:
Address:
Post Code:
Remarks:
1.This guarantee card to be kept by user,we will not re offer if lost.
2.This guarantee card should be filled by dealer,otherwise it`s
invalid.
3.Do not alter the guarantee card,please confirm that the serial
number on the guarantee card is the same with radio.
4.One-year guarantee for radio,half a year guarantee for
accessory.
5.Users can get maintenance service from following ways:

Go to the shop where you bought the radio

Find our local maintenance agent

Send back to our company
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Compliance and Control Guidelines and Operating Instructions
To control your exposure and ensure compliance with the occupational/controlled
environment exposure limits always adhere to the following procedures.
Guidelines:
Do not remove the RF Exposure Label from the device.
User awareness instructions should accompany device when transferred to other users.
Do not use this device if the operational requirements described herein are not met.
To control your exposure to RF and comply with the maximum exposure limits for
occupational/controlled environments, follow these guidelines:
■ Do not talk (transmit) on the radio more than the rated transmit duty cycle. This is
important because the radio radiates more energy when it is transmitting than when it is
receiving.
■ When listening and talking on the radio, hold it upright in front of your face so that it is
at least one inch (2.5 cm) away from any part of your face. Keeping the radio at the
recommended distance is important because exposure to RF decreases rapidly
the further away the antenna is from your body.
■ If you wear your radio, you must always put it in a carrying accessory carry accessory
that has been specifically approved by Tait for this radio. Using non-approved body-worn
accessories may mean you expose yourself to higher levels of RF than recommended by
the FCC’s occupational/controlled environment RF exposure limits.
■ Ensure you only use TEKK-approved antennas, batteries,and accessories.
This radio complies with the IEEE and ICNIRP exposure limits for occupational/
controlled RF exposure environments at operating duty factors of up to 50% talk to 50%
listen.
NOTICE:This radio is intended for use in occupational/controlled conditions, where
users have full knowledge of their exposure and can exercise control over their exposure
to meet FCC limits. This radio device is NOT authorized for general population,
consumer, or any other use.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : xm07095
Create Date                     : 2018:09:06 16:40:02+08:00
Modify Date                     : 2018:09:18 11:34:50-07:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:09:18 11:34:50-07:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - DP-150 English manual
Creator                         : xm07095
Document ID                     : uuid:357d3982-fa52-43d1-acbb-666368119f54
Instance ID                     : uuid:fd4f53e0-4110-470e-b4e7-6881b3349193
Page Count                      : 27

EXIF Metadata provided by EXIF.tools