Telit Communications S p A GE864QA Quad-band GPRS Cell Module / GE864-QUAD Automotive User Manual GE864 Harware User Guide
Telit Communications S.p.A. Quad-band GPRS Cell Module / GE864-QUAD Automotive GE864 Harware User Guide
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1068129 |
| Application ID | +TfbvxC/YpJFA3n7QoHWLg== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 283.33kB (3541660 bits) |
| Date Submitted | 2009-02-13 00:00:00 |
| Date Available | 2009-02-13 00:00:00 |
| Creation Date | 2008-06-25 10:14:46 |
| Producing Software | Acrobat Distiller 8.1.0 (Windows) |
| Document Lastmod | 2008-06-25 10:15:22 |
| Document Title | GE864 Harware User Guide |
| Document Creator | Acrobat PDFMaker 8.1 for Word |
| Document Author: | F D |
GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 This document is relating to the following products: GE864-AUTO 3990250701 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 2 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 Contents Overview ...........................................................................................................................6 GE864-AUTO Mechanical Dimensions ...........................................................................7 GE864-AUTO module connections .................................................................................8 3.1 PIN-OUT...................................................................................................................................8 3.1.1 Hardware Commands ....................................................................................................14 4.1 Turning ON the GE864-AUTO module ................................................................................14 4.2 Turning OFF the GE864-AUTO ............................................................................................16 4.2.1 4.2.2 BGA Balls Layout........................................................................................................................... 12 Hardware shutdown....................................................................................................................... 16 Hardware Unconditional Restart.................................................................................................... 16 Power Supply .................................................................................................................18 5.1 Power Supply Requirements ...............................................................................................18 5.2 General Design Rules ..........................................................................................................20 5.2.1 Electrical Design Guidelines .......................................................................................................... 20 5.2.1.1 + 5V input Source Power Supply Design Guidelines ................................................................ 20 5.2.1.2 + 12V input Source Power Supply Design Guidelines .............................................................. 21 5.2.1.3 Battery Source Power Supply Design Guidelines ..................................................................... 23 5.2.2 Thermal Design Guidelines ........................................................................................................... 24 5.2.3 Power Supply PCB layout Guidelines ........................................................................................... 25 Antenna...........................................................................................................................26 6.1 GSM Antenna Requirements ...............................................................................................26 6.2 GSM Antenna - PCB line Guidelines...................................................................................27 6.3 GSM Antenna - Installation Guidelines ..............................................................................28 Logic level specifications..............................................................................................29 7.1 Reset signal ..........................................................................................................................30 Serial Ports .....................................................................................................................31 8.1 MODEM SERIAL PORT.........................................................................................................31 8.2 RS232 level translation ........................................................................................................33 8.3 5V UART level translation....................................................................................................35 Audio Section Overview ................................................................................................37 9.1 INPUT LINES (Microphone) .................................................................................................38 9.1.1 9.1.2 Short description............................................................................................................................ 38 Input Lines Characteristics ............................................................................................................ 39 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 3 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 9.2 OUTPUT LINES (Speaker) ....................................................................................................40 9.2.1 9.2.2 Short description............................................................................................................................ 40 Output Lines Characteristics.......................................................................................................... 41 10 General Purpose I/O.......................................................................................................42 10.1 GPIO Logic levels .............................................................................................................44 10.2 Using a GPIO Pad as INPUT.............................................................................................45 10.3 Using a GPIO Pad as OUTPUT.........................................................................................45 10.4 Using the RF Transmission Control GPIO4....................................................................45 10.5 Using the RFTXMON Output GPIO5 ................................................................................46 10.6 Using the Alarm Output GPIO6........................................................................................47 10.7 Using the Buzzer Output GPIO7 ......................................................................................47 10.8 Indication of network service availability .......................................................................48 10.9 RTC Bypass out ................................................................................................................49 10.10 External 32KHz oscillator.................................................................................................49 11 ADC section....................................................................................................................51 11.1 11.1.1 11.1.2 11.2 11.2.1 11.2.2 11.2.3 11.2.4 11.2.5 11.2.6 11.2.7 11.2.8 11.3 11.3.1 11.3.2 ADC Converter ..................................................................................................................51 Description ..................................................................................................................................... 51 Using ADC Converter .................................................................................................................... 51 Mounting the GE864-AUTO on your Board ....................................................................52 General .......................................................................................................................................... 52 Module finishing & dimensions ...................................................................................................... 52 Recommended foot print for the application (GE864) ................................................................... 53 Debug of the GE864 in production ................................................................................................ 54 Stencil ............................................................................................................................................ 54 PCB pad design............................................................................................................................. 55 Solder paste................................................................................................................................... 56 GE864 Solder reflow...................................................................................................................... 57 Packing system.................................................................................................................58 GE864 orientation on the tray........................................................................................................ 59 Moisture sensibility ........................................................................................................................ 59 12 Conformity Assessment Issues ....................................................................................60 13 SAFETY RECOMMANDATIONS.....................................................................................61 14 Document Change Log ..................................................................................................62 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 4 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 DISCLAIMER The information contained in this document is the proprietary information of Telit Communications S.p.A. and its affiliates (“TELIT”). The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Telit, is strictly prohibited. Telit makes every effort to ensure the quality of the information it makes available. Notwithstanding the foregoing, Telit does not make any warranty as to the information contained herein, and does not accept any liability for any injury, loss or damage of any kind incurred by use of or reliance upon the information. Telit disclaims any and all responsibility for the application of the devices characterized in this document, and notes that the application of the device must comply with the safety standards of the applicable country, and where applicable, with the relevant wiring rules. Telit reserves the right to make modifications, additions and deletions to this document due to typographical errors, inaccurate information, or improvements to programs and/or equipment at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this application note. All rights reserved. © 2008 Telit Communications S.p.A. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 5 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 1 Overview The aim of this document is the description of some hardware solutions useful for developing a product with the Telit GE864-AUTO module. In this document all the basic functions of a mobile phone will be taken into account; for each one of them a proper hardware solution will be suggested and eventually the wrong solutions and common errors to be avoided will be evidenced. Obviously this document cannot embrace the whole hardware solutions and products that may be designed. The wrong solutions to be avoided shall be considered as mandatory, while the suggested hardware configurations shall not be considered mandatory, instead the information given shall be used as a guide and a starting point for properly developing your product with the Telit GE864-AUTO module. For further hardware details that may not be explained in this document refer to the Telit GE864-AUTO Product Description document where all the hardware information is reported. NOTICE (EN) The integration of the GSM/GPRS GE864-AUTO cellular module within user application shall be done according to the design rules described in this manual. (IT) L’integrazione del modulo cellulare GSM/GPRS GE864-AUTO all’interno dell’applicazione dell’utente dovrà rispettare le indicazioni progettuali descritte in questo manuale. (DE) Die integration des GE864-AUTO GSM/GPRS Mobilfunk-Moduls in ein Gerät muß gemäß der in diesem Dokument beschriebenen Kunstruktionsregeln erfolgen (SL) Integracija GSM/GPRS GE864-AUTO modula v uporabniški aplikaciji bo morala upoštevati projektna navodila, opisana v tem piročniku. (SP) La utilización del modulo GSM/GPRS GE864-AUTO debe ser conforme a los usos para los cuales ha sido deseñado descritos en este manual del usuario. (FR) L’intégration du module cellulaire GSM/GPRS GE864-AUTO dans l’application de l’utilisateur sera faite selon les règles de conception décrites dans ce manuel. GE864-AUTO The information presented in this document is believed to be accurate and reliable. However, no responsibility is assumed by Telit Communications S.p.A. for its use, nor any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent rights of Telit Communications S.p.A. other than for circuitry embodied in Telit products. This document is subject to change without notice. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 6 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 2 GE864-AUTO Mechanical Dimensions The Telit GE864-AUTO module overall dimension are: • • • Length: Width: Thickness: 30 mm 30 mm 2.8 mm Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 7 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 3 GE864-AUTO module connections 3.1 PIN-OUT Ball Signal I/O Function Internal PULL UP Type Audio F9 AXE G8 MIC_HF+ AI G9 MIC_MT- AI G10 EAR_MT+ AO J8 MIC_MT+ AI J9 MIC_HF- AI J10 EAR_HF- AO Handsfree switching Handsfree mic. input; phase +, nom. level 3mVrms Handset mic.signal input; phase-, nom. level 50mVrms Handset earphone signal output, phase + Handset mic.signal input; phase+, nom. level 50mVrms Handsfree mic.input; phase -, nom. level 3mVrms Handsfree ear output, phase - 100K CMOS 2.8V H9 EAR_MT- AO Handset earphone signal output, phase - Audio H10 EAR_HF+ AO Handsfree ear output, phase + Audio C10 SIMCLK External SIM signal – Clock C11 SIMIN External SIM signal - Presence (active low) D4 SIMVCC External SIM signal – Power supply for the SIM 1,8 / 3V D10 SIMIO I/O External SIM signal - Data I/O 1,8 / 3V E9 SIMRST External SIM signal – Reset 1,8 / 3V D11 TX_TRACE TX Data for debug monitor CMOS 2.8V F10 RX_TRACE RX Data for debug monitor CMOS 2.8V B6 C125/RING CMOS 2.8V B7 C108/DTR D9 C109/DCD E7 C103/TXD Output for Ring indicator signal (RI) to DTE Input for Data terminal ready signal (DTR) from DTE Output for Data carrier detect signal (DCD) to DTE Serial data input (TXD) from DTE E11 C107/DSR CMOS 2.8V F7 C105/RTS F6 C106/CTS Output for Data set ready signal (DSR) to DTE Input for Request to send signal (RTS) from DTE Output for Clear to send signal (CTS) to DTE H8 C104/RXD Serial data output to DTE CMOS 2.8V D2 IIC_SDA_HW I/O IIC HW interface /Configurable GPIO CMOS 2.8V E1 IIC_SCL_HW I/O IIC HW interface /Configurable GPIO CMOS 2.8V Audio Audio Audio Audio Audio Audio SIM card interface 1,8 / 3V 47K 1,8 / 3V Trace Prog. / Data + HW Flow Control CMOS 2.8V CMOS 2.8V CMOS 2.8V CMOS 2.8V CMOS 2.8V IIC Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 8 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 Ball Signal I/O Function Internal PULL UP Type DAC and ADC J11 ADC_IN1 AI Analog/Digital converter input A/D H11 ADC_IN2 AI Analog/Digital converter input A/D G11 ADC_IN3 AI Analog/Digital converter input A/D Miscellaneous Functions A2 RESET* Reset input D8 STAT_LED Status indicator led CMOS 1.8V E2 VRTC AO VRTC Power F3 32K_IN 32.768 KHz Square Wave Input CMOS 1.8V Pull up to VBATT J5 ON_OFF* Input command for switching power ON or OFF (toggle command). The pulse to be sent to the 47K GE864 must be equal or greater than 1 second. L8 PWRMON Power ON Monitor CMOS 2.8V L4 Antenna Antenna output – 50 ohm RF Telit GPIO E6 TGPIO_01 / JDR I/O Telit GPIO01 I/O pin / Jammer detect report CMOS 2.8V H5 TGPIO_02/PCM_WAO I/O Telit GPIO02 Configurable GPIO / PCM audio * CMOS 2.8V K7 TGPIO_03 / PCM_RX I/O CMOS 2.8V B3 TGPIO_04 I/O K8 TGPIO_05 / RFTXMON I/O B5 TGPIO_06 / ALARM I/O Telit GPIO03 Configurable GPIO / PCM audio * Telit GPIO04 Configurable GPIO / RF Transmission Control Telit GPIO05 Configurable GPIO / Transmitter ON monitor Telit GPIO06 Configurable GPIO / ALARM L9 TGPIO_07 / BUZZER I/O Telit GPIO07 Configurable GPIO / Buzzer CMOS 2.8V H3 TGPIO_08 / PCM_TX I/O Telit GPIO08 Configurable GPIO / PCM audio * CMOS 2.8V D7 PCM_CLK I/O Configurable GPIO / PCM audio * CMOS 2.8V CMOS 2.8V CMOS 2.8V CMOS 2.8V Power Supply J1 VBATT Main power supply Power K1 VBATT Main power supply Power J2 VBATT Main power supply Power K2 VBATT Main power supply Power A1 GND Ground Power F1 GND Ground Power H1 GND Ground Power L1 GND Ground Power H2 GND Ground Power L2 GND Ground Power J3 GND Ground Power K3 GND Ground Power L3 GND Ground Power K4 GND Ground Power K5 GND Ground Power D6 GND Ground Power K6 GND Ground Power L6 GND Ground Power Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 9 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 Ball Signal I/O Function Internal PULL UP Type A11 GND Ground Power F11 GND Ground Power L11 GND Ground Power RESERVED A3 A4 A5 A6 A7 A8 A9 A10 B1 B2 B4 B8 B9 B10 B11 C1 C2 C3 C4 C5 C6 C7 C8 C9 D1 D3 D5 E3 E4 E5 E8 E10 F2 F4 F5 F8 G1 G2 G3 G4 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 10 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 Ball Signal I/O Function Internal PULL UP Type G5 G6 G7 H4 H6 H7 J4 J6 J7 K9 K10 K11 L5 L7 L10 * Ref. to Digital Voice Interface Application Note 80000NT10004a. NOTE: RESERVED pins must not be connected NOTE: If not used, almost all pins should be left disconnected. The only exceptions are the following pins: pin signal VBATT J1,K1,J2,K2 GND A1,F1,H1,L1,H2,L2,J3,K3,L3, K4,K5,D6,K6,L6,A11,F11,L11 ON/OFF* J5 TXD E7 RESET* A2 RXD H8 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 11 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 3.1.1 BGA Balls Layout TOP VIEW GND IIC_SCL_ HW GND GND VBATT VBATT GND RESET* IIC_SDA_ HW VRTC GND VBATT VBATT GND TGPIO_04 32K_IN TGPIO_08 / PCM_TX GND GND GND -- SIMVCC GND Antenna TGPIO_06 / ALARM TGPIO_02 / PCM_WAO ON_OFF* GND C125/RING GND TGPIO_01 / JDR C106 / CTS GND GND C108 / DTR PCM_CLK C103 / TXD C105 / RTS TGPIO_03/ PCM_RX STAD_ LED MIC_HF+ C104 / RXD MIC_MT+ TGPIO_05 RFTXMON PWRMON C109 / DCD SIMRST AXE MIC_MT- EAR_MT- MIC_HF- TGPIO_07 / BUZZER 10 SIMCLK SIMIO RX_TRACE EAR_MT+ EAR_HF+ EAR_HF- 11 GND SIMIN TX_TRACE C107 / DSR GND ADC_IN3 ADC_IN2 ADC_IN1 GND Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 12 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 AUDIO Signals balls SIM CARD interface balls TRACE Signals balls Prog. / data + Hw Flow Control signals balls IIC DAC and ADC signals balls MISCELLANEOUS functions signals balls TELIT GPIO balls POWER SUPPLY VBATT balls POWER SUPPLY GND balls RESERVED Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 13 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 4 Hardware Commands 4.1 Turning ON the GE864-AUTO module To turn on the GE864-AUTO the pad ON* must be tied low for at least 1 seconds and then released. The maximum current that can be drained from the ON* pad is 0,1 mA. A simple circuit to do it is: ON* R1 Q1 Power ON impulse R2 GND NOTE: don't use any pull up resistor on the ON* line, it is internally pulled up. Using pull up resistor may bring to latch up problems on the GE864-AUTO power regulator and improper power on/off of the module. The line ON* must be connected only in open collector configuration. NOTE: In this document all the lines that are inverted, hence have active low signals are labeled with a name that ends with a "*" . TIP: To check if the device has powered on, the hardware line PWRMON should be monitored. After 900ms the line raised up the device could be considered powered on. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 14 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 For example: 1- Let's assume you need to drive the ON* pad with a totem pole output from +1.8V up to 5V microcontroller (uP_OUT1): 10k ON* +1.8V ... 5V 1s 2- Let's assume you need to drive the ON* pad directly with an ON/OFF button: ON* Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 15 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 4.2 Turning OFF the GE864-AUTO The turning off of the device can be done in three ways: • by software command (see GE864-AUTO Software User Guide) • by hardware shutdown • by Hardware Unconditional Restart When the device is shut down by software command or by hardware shutdown, it issues to the network a detach request that informs the network that the device will not be reachable any more. 4.2.1 Hardware shutdown To turn OFF the GE864-AUTO the pad ON* must be tied low for at least 2 seconds and then released. The same circuitry and timing for the power on shall be used. The device shuts down after the release of the ON* pad. TIP: To check if the device has powered off, the hardware line PWRMON should be monitored. When PWRMON goes low, the device has powered off. 4.2.2 Hardware Unconditional Restart To unconditionally Restart the GE864-AUTO, the pad RESET* must be tied low for at least 200 milliseconds and then released. A simple circuit to do it is: RESET* Unconditional Restart impulse GND Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 16 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 NOTE: don't use any pull up resistor on the RESET* line nor any totem pole digital output. Using pull up resistor may bring to latch up problems on the GE864-AUTO power regulator and improper functioning of the module. The line RESET* must be connected only in open collector configuration. TIP: The unconditional hardware Restart should be always implemented on the boards and software should use it as an emergency exit procedure. For example: 1- Let's assume you need to drive the RESET* pad with a totem pole output from +1.8V up to +5V microcontroller (uP_OUT2): 10k RESET* 1.8V ... 5V Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 17 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 5 Power Supply The power supply circuitry and board layout are a very important part in the full product design and they strongly reflect on the product overall performances, hence read carefully the requirements and the guidelines that will follow for a proper design. 5.1 Power Supply Requirements POWER SUPPLY Nominal Supply Voltage 3.8V Max Supply Voltage 4.2V Operating Supply Voltage Range 3.4V – 4.2V Wide Supply Voltage tolerant 3.25V – 4.2V TIP: the supply voltage is directly measured between VBATT and GND balls. It must stay within the Wide Supply Voltage tolerant range including any drop voltage and overshoot voltage (during the slot tx, for example). Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 18 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 The GE864-AUTO power consumptions are: GE864-AUTO Mode Average (mA) Mode description Stand by mode; no call in progress IDLE mode Normal mode: full functionality of the module AT+CFUN=1 23,9 AT+CFUN=4 22 AT+CFUN=0 or AT+CFUN=5 7,20 / 3,561 RX mode 1 slot in downlink 52,3 2 slot in downlink 65,2 3 slot in downlink 78,6 4 slot in downlink 88,4 GSM TX and RX mode Min power level 78,1 Max power level 200,1 GPRS (class 10) TX and RX mode Min power level 123,7 Max power level 370,8 Disabled TX and RX; module is not registered on the network Power saving: CFUN=0 module registered on the network and can receive voice call or an SMS; but it is not possible to send AT commands; module wakes up with an unsolicited code (call or SMS) or rising RTS line. CFUN=5 full functionality with power saving; module registered on the network can receive incoming calls and SMS GSM Receiving data mode GSM Sending data mode GPRS Sending data mode The GSM system is made in a way that the RF transmission is not continuous, else it is packed into bursts at a base frequency of about 216 Hz, the relative current peaks can be as high as about 2A. Therefore the power supply has to be designed in order to withstand with these current peaks without big voltage drops; this means that both the electrical design and the board layout must be designed for this current flow. If the layout of the PCB is not well designed a strong noise floor is generated on the ground and the supply; this will reflect on all the audio paths producing an audible annoying noise at 216 Hz; if the voltage drop during the peak current absorption is too much, then the device may even shutdown as a consequence of the supply voltage drop. TIP: The electrical design for the Power supply should be made ensuring it will be capable of a peak current output of at least 2A. Worst/best case depends on network configuration and is not under module control Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 19 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 5.2 General Design Rules The principal guidelines for the Power Supply Design embrace three different design steps: • the electrical design • the thermal design • the PCB layout. 5.2.1 Electrical Design Guidelines The electrical design of the power supply depends strongly from the power source where this power is drained. We will distinguish them into three categories: • +5V input (typically PC internal regulator output) • +12V input (typically automotive) • Battery 5.2.1.1 + 5V input Source Power Supply Design Guidelines • • • • • The desired output for the power supply is 3.8V, hence there's not a big difference between the input source and the desired output and a linear regulator can be used. A switching power supply will not be suited because of the low drop out requirements. When using a linear regulator, a proper heat sink shall be provided in order to dissipate the power generated. A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current absorption peaks close to the GE864-AUTO, a 100μF tantalum capacitor is usually suited. Make sure the low ESR capacitor on the power supply output (usually a tantalum one) is rated at least 10V. A protection diode should be inserted close to the power input, in order to save the GE864-AUTO from power polarity inversion. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 20 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 An example of linear regulator with 5V input is: 5.2.1.2 + 12V input Source Power Supply Design Guidelines • • • • • • • • The desired output for the power supply is 3.8V, hence due to the big difference between the input source and the desired output, a linear regulator is not suited and shall not be used. A switching power supply will be preferable because of its better efficiency especially with the 2A peak current load represented by the GE864-AUTO. When using a switching regulator, a 500kHz or more switching frequency regulator is preferable because of its smaller inductor size and its faster transient response. This allows the regulator to respond quickly to the current peaks absorption. In any case the frequency and Switching design selection is related to the application to be developed due to the fact the switching frequency could also generate EMC interferences. For car PB battery the input voltage can rise up to 15,8V and this should be kept in mind when choosing components: all components in the power supply must withstand this voltage. A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current absorption peaks, a 100μF tantalum capacitor is usually suited. Make sure the low ESR capacitor on the power supply output (usually a tantalum one) is rated at least 10V. For Car applications a spike protection diode should be inserted close to the power input, in order to clean the supply from spikes. A protection diode should be inserted close to the power input, in order to save the GE864-AUTO from power polarity inversion. This can be the same diode as for spike protection. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 21 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 An example of switching regulator with 12V input is in the below schematic (it is split in 2 parts): Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 22 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 5.2.1.3 Battery Source Power Supply Design Guidelines • The desired nominal output for the power supply is 3.8V and the maximum voltage allowed is 4.2V, hence a single 3.7V Li-Ion cell battery type is suited for supplying the power to the Telit GE864-AUTO module. The three cells Ni/Cd or Ni/MH 3,6 V Nom. battery types or 4V PB types MUST NOT BE USED DIRECTLY since their maximum voltage can rise over the absolute maximum voltage for the GE864-AUTO and damage it. NOTE: DON'T USE any Ni-Cd, Ni-MH, and Pb battery types directly connected with GE864-AUTO. Their use can lead to overvoltage on the GE864-AUTO and damage it. USE ONLY Li-Ion battery types. • • • • A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current absorption peaks, a 100μF tantalum capacitor is usually suited. Make sure the low ESR capacitor (usually a tantalum one) is rated at least 10V. A protection diode should be inserted close to the power input, in order to save the GE864-AUTO from power polarity inversion. Otherwise the battery connector should be done in a way to avoid polarity inversions when connecting the battery. The battery capacity must be at least 500mAh in order to withstand the current peaks of 2A; the suggested capacity is from 500mAh to 1000mAh. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 23 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 5.2.2 Thermal Design Guidelines The thermal design for the power supply heat sink should be done with the following specifications: • Average current consumption during transmission @PWR level max: 500mA • Average current consumption during transmission @ PWR level min: 100mA • Average current during Power Saving (CFUN=5): 4mA • Average current during idle (Power Saving disabled) 24mA NOTE: The average consumption during transmissions depends on the power level at which the device is requested to transmit by the network. The average current consumption hence varies significantly. Considering the very low current during idle, especially if Power Saving function is enabled, it is possible to consider from the thermal point of view that the device absorbs current significantly only during calls. If we assume that the device stays into transmission for short periods of time (let's say few minutes) and then remains for a quite long time in idle (let's say one hour), then the power supply has always the time to cool down between the calls and the heat sink could be smaller than the calculated one for 500mA maximum RMS current, or even could be the simple chip package (no heat sink). Moreover in the average network conditions the device is requested to transmit at a lower power level than the maximum and hence the current consumption will be less than the 500mA, being usually around 150mA. For these reasons the thermal design is rarely a concern and the simple ground plane where the power supply chip is placed can be enough to ensure a good thermal condition and avoid overheating. For the heat generated by the GE864-AUTO, you can consider it to be during transmission 1W max during CSD/VOICE calls and 2W max during class10 GPRS upload. This generated heat will be mostly conducted to the ground plane under the GE864-AUTO; you must ensure that your application can dissipate it. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 24 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 5.2.3 Power Supply PCB layout Guidelines As seen on the electrical design guidelines the power supply shall have a low ESR capacitor on the output to cut the current peaks and a protection diode on the input to protect the supply from spikes and polarity inversion. The placement of these components is crucial for the correct working of the circuitry. A misplaced component can be useless or can even decrease the power supply performances. • • • • • • • • The Bypass low ESR capacitor must be placed close to the Telit GE864-AUTO power input pads or in the case the power supply is a switching type it can be placed close to the inductor to cut the ripple provided the PCB trace from the capacitor to the GE864-AUTO is wide enough to ensure a dropless connection even during the 2A current peaks. The protection diode must be placed close to the input connector where the power source is drained. The PCB traces from the input connector to the power regulator IC must be wide enough to ensure no voltage drops occur when the 2A current peaks are absorbed. Note that this is not made in order to save power loss but especially to avoid the voltage drops on the power line at the current peaks frequency of 216 Hz that will reflect on all the components connected to that supply, introducing the noise floor at the burst base frequency. For this reason while a voltage drop of 300400 mV may be acceptable from the power loss point of view, the same voltage drop may not be acceptable from the noise point of view. If your application doesn't have audio interface but only uses the data feature of the Telit GE864-AUTO, then this noise is not so disturbing and power supply layout design can be more forgiving. The PCB traces to the GE864-AUTO and the Bypass capacitor must be wide enough to ensure no significant voltage drops occur when the 2A current peaks are absorbed. This is for the same reason as previous point. Try to keep this trace as short as possible. The PCB traces connecting the Switching output to the inductor and the switching diode must be kept as short as possible by placing the inductor and the diode very close to the power switching IC (only for switching power supply). This is done in order to reduce the radiated field (noise) at the switching frequency (100-500 kHz usually). The use of a good common ground plane is suggested. The placement of the power supply on the board should be done in such a way to guarantee that the high current return paths in the ground plane are not overlapped to any noise sensitive circuitry as the microphone amplifier/buffer or earphone amplifier. The power supply input cables should be kept separate from noise sensitive lines such as microphone/earphone cables. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 25 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 6 Antenna The antenna connection and board layout design are the most important part in the full product design and they strongly reflect on the product overall performances, hence read carefully and follow the requirements and the guidelines for a proper design. 6.1 GSM Antenna Requirements As suggested on the Product Description the antenna and antenna line on PCB for a Telit GE864AUTO device shall fulfill the following requirements: ANTENNA REQUIREMENTS Frequency range Bandwidth Gain Impedance Input power VSWR absolute max VSWR recommended Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for that/those band(s) 70 MHz in GSM850, 80 MHz in GSM900, 170 MHz in DCS & 140 MHz PCS band Gain < 3dBi 50 ohm > 2 W peak power <= 10:1 <= 2:1 When using the Telit GE864-AUTO, since there's no antenna connector on the module, the antenna must be connected to the GE864-AUTO through the PCB with the antenna pad. In the case that the antenna is not directly developed on the same PCB, hence directly connected at the antenna pad of the GE864-AUTO, then a PCB line is needed in order to connect with it or with its connector. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 26 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 This line of transmission shall fulfill the following requirements: ANTENNA LINE ON PCB REQUIREMENTS 50 ohm Impedance 0,3 dB Max Attenuation No coupling with other signals allowed Cold End (Ground Plane) of antenna shall be equipotential to the GE864-AUTO ground pins Furthermore if the device is developed for the US market and/or Canada market, it shall comply to the FCC and/or IC approval requirements: This device is to be used only for mobile and fixed application. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. OEM integrators must ensure that the end user has no manual instructions to remove or install the GE864-AUTO module. Antennas used for this OEM module must not exceed 3dBi gain for mobile and fixed operating configurations. 6.2 GSM Antenna - PCB line Guidelines • • • • • • • • • • Ensure that the antenna line impedance is 50 ohm; Keep the antenna line on the PCB as short as possible, since the antenna line loss shall be less than 0,3 dB; Antenna line must have uniform characteristics, constant cross section, avoid meanders and abrupt curves; Keep, if possible, one layer of the PCB used only for the Ground plane; Surround (on the sides, over and under) the antenna line on PCB with Ground, avoid having other signal tracks facing directly the antenna line track; The ground around the antenna line on PCB has to be strictly connected to the Ground Plane by placing vias once per 2mm at least; Place EM noisy devices as far as possible from GE864-AUTO antenna line; Keep the antenna line far away from the GE864-AUTO power supply lines; If you have EM noisy devices around the PCB hosting the GE864-AUTO, such as fast switching ICs, take care of the shielding of the antenna line by burying it inside the layers of PCB and surround it with Ground planes, or shield it with a metal frame cover. If you don't have EM noisy devices around the PCB of GE864-AUTO, by using a strip-line on the superficial copper layer for the antenna line, the line attenuation will be lower than a buried one; Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 27 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 6.3 GSM Antenna - Installation Guidelines • • • • Install the antenna in a place covered by the GSM signal. The Antenna must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter; Antenna shall not be installed inside metal cases Antenna shall be installed also according Antenna manufacturer instructions. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 28 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 7 Logic level specifications Where not specifically stated, all the interface circuits work at 2.8V CMOS logic levels. The following table shows the logic level specifications used in the Telit GE864-AUTO interface circuits: Absolute Maximum Ratings -Not Functional Parameter Min Max Input level on any -0.3V digital pin when on Input voltage on -0.3V analog pins when on Voltage on Buffered -0.3V pins +3.6V +3.0 V 25V Operating Range - Interface levels (2.8V CMOS) Level Min Max Input high level 2.1V 3.3V Input low level Output high level Output low level 0V 2.2V 0V 0.5V 3.0V 0.35V For 1,8V signals: Operating Range - Interface levels (1.8V CMOS) Level Min Max Input high level 1.6V 2.2V Input low level Output high level Output low level 0V 1,65V 0V 0.4V 2.2V 0.35V Current characteristics Level Typical Output Current 1mA Input Current 1uA Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 29 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 7.1 Reset signal Signal RESET Function Phone reset I/O Bga Ball A2 RESET is used to reset the GE864-AUTO modules. Whenever this signal is pulled low, the GE864-AUTO is reset. When the device is reset it stops any operation. After the release of the reset GE864-AUTO is unconditionally shut down, without doing any detach operation from the network where it is registered. This behaviour is not a proper shut down because any GSM device is requested to issue a detach request on turn off. For this reason the Reset signal must not be used to normally shutting down the device, but only as an emergency exit in the rare case the device remains stuck waiting for some network response. The RESET is internally controlled on start-up to achieve always a proper power-on reset sequence, so there's no need to control this pin on start-up. It may only be used to reset a device already on that is not responding to any command. NOTE: do not use this signal to power off the GE864-AUTO. Use the ON/OFF signal to perform this function or the AT#SHDN command. Reset Signal Operating levels: Signal RESET Input high RESET Input low Min 2.0V* 0V Max 2.2V 0.2V * this signal is internally pulled up so the pin can be left floating if not used. If unused, this signal may be left unconnected. If used, then it must always be connected with an open collector transistor, to permit to the internal circuitry the power on reset and under voltage lockout functions. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 30 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 8 Serial Ports The serial port on the Telit GE864-AUTO is the core of the interface between the module and OEM hardware. 2 serial ports are available on the module: • MODEM SERIAL PORT • MODEM SERIAL PORT 2 (DEBUG) 8.1 MODEM SERIAL PORT Several configurations can be designed for the serial port on the OEM hardware, but the most common are: • RS232 PC com port • microcontroller UART @ 2.8V - 3V (Universal Asynchronous Receive Transmit) • microcontroller UART@ 5V or other voltages different from 2.8V Depending from the type of serial port on the OEM hardware a level translator circuit may be needed to make the system work. The only configuration that doesn't need a level translation is the 2.8V UART. The serial port on the GE864-AUTO is a +2.8V UART with all the 7 RS232 signals. It differs from the PC-RS232 in the signal polarity (RS232 is reversed) and levels. The levels for the GE864-AUTO UART are the CMOS levels: Absolute Maximum Ratings -Not Functional Parameter Min Max Input level on any digital pad when on Input voltage on analog pads when on -0.3V +3.6V -0.3V +3.0 V Operating Range - Interface levels (2.8V CMOS) Level Min Max Input high level VIH 2.1V 3.3V Input low level VIL 0V 0.5V Output high level VOH 2.2V 3.0V Output low level VOL 0V 0.35V Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 31 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 The signals of the GE864-AUTO serial port are: RS232 Pin Number Signal Name Usage DCD - dcd_uart GE864AUTO Pad Number D9 Data Carrier Detect RXD - tx_uart TXD - rx_uart DTR - dtr_uart H8 E7 B7 Transmit line *see Note Receive line *see Note Data Terminal Ready GND Ground DSR - dsr_uart A1,F1,H1 L1, H2, L2, J3, K3…. E11 Output from the GE864-AUTO that indicates the carrier presence Output transmit line of GE864-AUTO UART Input receive of the GE864-AUTO UART Input to the GE864-AUTO that controls the DTE READY condition ground Data Set Ready RTS -rts_uart F7 Request to Send CTS - cts_uart F6 Clear to Send RI - ri_uart B6 Ring Indicator Output from the GE864-AUTO that indicates the module is ready Input to the GE864-AUTO that controls the Hardware flow control Output from the GE864-AUTO that controls the Hardware flow control Output from the GE864-AUTO that indicates the incoming call condition NOTE: According to V.24, RX/TX signal names are referred to the application side, therefore on the GE864 side these signal are on the opposite direction: TXD on the application side will be connected to the receive line (here named TXD/ rx_uart ) of the GE864-AUTO serial port and viceversa for RX. TIP: For a minimum implementation, only the TXD and RXD lines can be connected, the other lines can be left open provided a software flow control is implemented. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 32 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 8.2 RS232 level translation In order to interface the Telit GE864-AUTO with a PC com port or a RS232 (EIA/TIA-232) application a level translator is required. This level translator must invert the electrical signal in both directions change the level from 0/3V to +15/-15V Actually, the RS232 UART 16450, 16550, 16650 & 16750 chipsets accept signals with lower levels on the RS232 side (EIA/TIA-562) , allowing for a lower voltage-multiplying ratio on the level translator. Note that the negative signal voltage must be less than 0V and hence some sort of level translation is always required. The simplest way to translate the levels and invert the signal is by using a single chip level translator. There are a multitude of them, differing in the number of driver and receiver and in the levels (be sure to get a true RS232 level translator not a RS485 or other standards). By convention the driver is the level translator from the 0-3V UART level to the RS232 level, while the receiver is the translator from RS232 level to 0-3V UART. In order to translate the whole set of control lines of the UART you will need: 5 driver 3 receiver NOTE: The digital input lines working at 2.8VCMOS have an absolute maximum input voltage of 3,75V; therefore the level translator IC shall not be powered by the +3.8V supply of the module. Instead it shall be powered from a +2.8V / +3.0V (dedicated) power supply. This is because in this way the level translator IC outputs on the module side (i.e. GE864 inputs) will work at +3.8V interface levels, stressing the module inputs at its maximum input voltage. This can be acceptable for evaluation purposes, but not on production devices. NOTE: In order to be able to do in circuit reprogramming of the GE864 firmware, the serial port on the Telit GE864 shall be available for translation into RS232 and either it's controlling device shall be placed into tristate, disconnected or as a gateway for the serial data when module reprogramming occurs. Only RXD, TXD, GND and the On/off module turn on pad are required to the reprogramming of the module, the other lines are unused. All applicator shall include in their design such a way of reprogramming the GE864. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 33 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 An example of level translation circuitry of this kind is: The RS232 serial port lines are usually connected to a DB9 connector with the following layout: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 34 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 8.3 5V UART level translation If the OEM application uses a microcontroller with a serial port (UART) that works at a voltage different from 2.8 - 3V, then a circuitry has to be provided to adapt the different levels of the two set of signals. As for the RS232 translation there are a multitude of single chip translators. For example a possible translator circuit for a 5V TRANSMITTER/RECEIVER can be: TO TELIT MODULE TIP: This logic IC for the level translator and 2.8V pull-ups (not the 5V one) can be powered directly from PWRMON line of the GE864-AUTO. Note that the TC7SZ07AE has open drain output, therefore the resistor R2 is mandatory. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 35 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 NOTE: The UART input line TXD (rx_uart) of the GE864-AUTO is NOT internally pulled up with a resistor, so there may be the need to place an external 47KΩ pull-up resistor, either the DTR (dtr_uart) and RTS (rts_uart) input lines are not pulled up internally, so an external pull-up resistor of 47KΩ may be required. A power source of the internal interface voltage corresponding to the 2.8VCMOS high level is available at the PWRMON pin on the connector, whose absolute maximum output current is 1mA. A maximum of 9 resistors of 47 KΩ pull-up can be connected to the PWRMON pin, provided no other devices are connected to it and the pulled-up lines are GE864-AUTO input lines connected to open collector outputs in order to avoid latch-up problems on the GE864-AUTO. Care must be taken to avoid latch-up on the GE864-AUTO and the use of this output line to power electronic devices shall be avoided, especially for devices that generate spikes and noise such as switching level translators, micro controllers, failure in any of these condition can severely compromise the GE864-AUTO functionality. NOTE: The input lines working at 2.8VCMOS can be pulled-up with 47KΩ resistors that can be connected directly to the PWRMON line provided they are connected as in this example. NO OTHER devices than those suggested should be powered with the PWRMON line; otherwise the module functionality may be compromised. It is important to consider that the added circuit must have consumption lower than 1mA. In case of reprogramming of the module has to be considered the use of the RESET line to start correctly the activity. The preferable configuration is having an external supply for the buffer. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 36 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 9 Audio Section Overview 16 -12dBFS 16 audio2.skd The Base Band Chip of the GE864-AUTO Telit Module provides two different audio blocks; both in transmit (Uplink) and in receive (Downlink) direction: “MT lines” should be used for handset function, “HF lines” is suited for hands -free function (car kit). These two blocks can be active only one at a time, selectable by AXE hardware line or by AT command.The audio characteristics are equivalent in transmit blocks, but are different in the receive ones and this should be kept in mind when designing. Single ended Ear_HF- GE863-GPS Audio Paths Ear_HF+ Mic_HF+ Mic_HF- Ear_MT- Balanced 23mVrms 365mV rms +20dB +10dB -45dBV/Pa 0,33mV rms 50cm 7cm -45dBV/Pa 3,3mV rms Mic_MT- Ear_MT+ Mic_MT+ GM863-GPS Differential Line-Out Drivers Fully Differential Power Buffers EXTERNAL AMPLIFIER Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 37 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 9.1 INPUT LINES (Microphone) 9.1.1 Short description The Telit GE864-AUTO provides two audio paths in transmit section. Only one of the two paths can be active at a time, selectable by AXE hardware line or by AT command. You must keep in mind the different audio characteristics of the transmit blocks when designing: The “MIC_MT” audio path should be used for handset function, while the “MIC_HF” audio path is suited for hands-free function (car kit). TIP: being the microphone circuitry the more noise sensitive, its design and layout must be done with particular care. Both microphone paths are balanced and the OEM circuitry should be balanced designed to reduce the common mode noise typically generated on the ground plane. However also an unbalanced circuitry can be used for particular OEM application needs. TIP: due to the difference in the echo canceller type, the “Mic_MT” audio path is suited for Handset applications, while the “Mic_HF”audio path is suited for hands-free function (car kit). The Earphone applications should be made using the “Mic_HF” audio path but DISABLING the echo canceller by software AT command. If the echo canceller is left active with the Earphone, then some echo might be introduced by the echo cancel algorithm. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 38 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 9.1.2 Input Lines Characteristics “MIC_MT” 1st differential microphone path Line Coupling AC* Line Type Balanced Coupling capacitor ≥ 100nF Differential input resistance Differential input voltage Microphone nominal sensitivity 50kΩ ≤ 1,03Vpp (365mVrms) -45 dBVrms/Pa Analog gain suggested + 20dB Echo canceller type Handset “MIC_HF” 2nd differential microphone path Line Coupling AC* Line Type Balanced Coupling capacitor ≥ 100nF Differential input resistance Differential input voltage Microphone nominal sensitivity Analog gain suggested Echo canceller type 50kΩ ≤ 65mVpp (23mVrms) -45 dBVrms/Pa +10dB Car kit hands-free (*) WARNING: AC means that the signals from microphone has to be connected to input lines of the module by a CAPACITOR, which value must be ≥ 100nF. Not respecting this constraint, the input stage will be damaged. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 39 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 9.2 OUTPUT LINES (Speaker) 9.2.1 Short description The Telit GE864-AUTO provides two audio paths in receive section. Only one of the two paths can be active at a time, selectable by AXE hardware line or by AT command. You must keep in mind the different audio characteristics of the receive blocks when designing: Æ the “EAR_MT” lines EPN1 and EPP1 are the Differential Line-Out Drivers ; they can drive an external amplifier or directly a 16 Ω earpiece at –12dBFS (*) ; Æ the “EAR_HF” lines EPPA1_2 and EPPA2 are the Fully Differential Power Buffers ; they can directly drive a 16Ω speaker in differential (balanced) or single ended (unbalanced) operation mode . (*) FS : acronym of Full Scale. It is equal to 0dB, the maximum Hardware Analog Receive Gain of BaseBand Chip. The “EAR_MT” audio path should be used for handset function, while the “EAR_HF” audio path is suited for hands-free function (car kit). Both receiver outputs are B.T.L. type (Bridged Tie Load) and the OEM circuitry shall be designed bridged to reduce the common mode noise typically generated on the ground plane and to get the maximum power output from the device; however also a single ended circuitry can be designed for particular OEM application needs. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 40 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 9.2.2 Output Lines Characteristics “EAR_MT” Differential Line-out Drivers Path Line Coupling DC Line Type Bridged Output load resistance ≥ 14 Ω Internal output resistance Signal bandwidth 4 Ω (typical) 150 – 4000 Hz @ -3 dB Differential output voltage SW volume level step Number of SW volume steps 328mVrms /16 Ω @ -12dBFS - 2 dB 10 “EAR_HF” Power Buffers Path Line Coupling DC Line Type Bridged Output load resistance ≥ 14 Ω Internal output resistance Signal bandwidth 4 Ω ( >1,7 Ω ) 150 – 4000 Hz @ -3 dB Max Differential output voltage 1310 mVrms (typ, open circuit) Max Single Ended output voltage 656 mVrms (typ, open circuit) SW volume level step Number of SW volume steps - 2 dB 10 For more detailed information about audio please refer to the Audio Settings Application Note 80000NT10007a. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 41 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 10 General Purpose I/O The general purpose I/O pads can be configured to act in three different ways: • input • output • alternate function (internally controlled) Input pads can only be read and report the digital value (high or low) present on the pad at the read time; output pads can only be written or queried and set the value of the pad output; an alternate function pad is internally controlled by the GE864-AUTO firmware and acts depending on the function implemented. For Logic levels please refer to chapter 7. The following GPIO are available on the GE864-AUTO: Ball Signal I/O Function Type Input / output current Default State State during Reset B3 TGPIO_04 I/O GPIO04 Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT B5 TGPIO_06 I/O GPIO06 Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT Note Alternate function (RF Transmission Control) Alternate function (ALARM) Alternate function (JDR) E6 TGPIO_01 I/O GPIO01 Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT HIGH (see Fig.01) H3 TGPIO_08 I/O GPIO08 Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT PCM_TX H5 TGPIO_02 I/O GPIO02 Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT PCM_WAO K7 TGPIO_03 I/O GPIO03 Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT K8 TGPIO_05 I/O GPIO05 Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT L9 TGPIO_07 I/O GPIO07 Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT D7 PCM_CLK I/O Configurable GPIO CMOS 2.8V 1uA / 1mA INPUT PCM_RX Alternate function (RFTXMON) Alternate function (BUZZER) PCM audio * Not all GPIO pads support all these three modes: • GPIO1 supports all three modes and can be input, output, Jamming Detect Output (Alternate function) • GPIO4 supports all three modes and can be input, output, RF Transmission Control (Alternate function) • GPIO5 supports all three modes and can be input, output, RFTX monitor output (Alternate function) • GPIO6 supports all three modes and can be input, output, alarm output (Alternate function) • GPIO7 supports all three modes and can be input, output, buzzer output (Alternate function) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 42 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 ch1: ON_OFF (2sec) ch2: GPIO 06 [ bis ] GE864-AUTO Fig.01 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 43 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 10.1 GPIO Logic levels Where not specifically stated, all the interface circuits work at 2.8V CMOS logic levels. The following table shows the logic level specifications used in the GE864-AUTO interface circuits: Absolute Maximum Ratings -Not Functional Parameter Min Max Input level on any -0.3V digital pin when on Input voltage on -0.3V analog pins when on +3.6V +3.0 V Operating Range - Interface levels (2.8V CMOS) Level Min Max Input high level 2.1V 3.3V Input low level Output high level Output low level 0V 2.2V 0V 0.5V 3.0V 0.35V For 1,8V signals: Operating Range - Interface levels (1.8V CMOS) Level Min Max Input high level 1.6V 2.2V Input low level Output high level Output low level 0V 1,65V 0V 0.4V 2.2V 0.35V Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 44 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 10.2 Using a GPIO Pad as INPUT The GPIO pads, when used as inputs, can be connected to a digital output of another device and report its status, provided this device has interface levels compatible with the 2.8V CMOS levels of the GPIO. If the digital output of the device to be connected with the GPIO input pad has interface levels different from the 2.8V CMOS, then it can be buffered with an open collector transistor with a 47K pull up to 2.8V. 10.3 Using a GPIO Pad as OUTPUT The GPIO pads, when used as outputs, can drive 2.8V CMOS digital devices or compatible hardware. When set as outputs, the pads have a push-pull output and therefore the pull-up resistor may be omitted. 10.4 Using the RF Transmission Control GPIO4 The GPIO4 pin, when configured as RF Transmission Control Input, permits to disable the Transmitter when the GPIO is set to Low by the application. In the design is necessary to add a pull up resistor (47K to PWRMON); Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 45 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 10.5 Using the RFTXMON Output GPIO5 The GPIO5 pin, when configured as RFTXMON Output, is controlled by the GE864-AUTO module and will rise when the transmitter is active and fall after the transmitter activity is completed. The TXMON pin behaviour can be configured using the AT command # TXMONMODE This command will be available only under AT#SELINT=2. # TXMONMODE – TTY-CTM DSP operating mode # TXMONMODE – Set TXMON pin behaviour Set TXMON pin behaviour. AT# TXMONMODE =Parameter: 0 – TXMON pin goes high when a call is started and it drops down when the call is ended. It also goes high when a location update starts, and it drops down when the location update procedure stops. Finally it goes high during SMS transmission and receiving. Even if the TXMON in this case is set as GPIO in output, the read command AT#GPIO=5,2 returns #GPIO:2,0, as the GPIO is in alternate mode. 1 – TXMON is set in alternate mode and the Timer unit controls its state. TXMON goes high 200μs before TXEN goes high. Then power ramps start raising and there is the burst transmission. Finally TXMON drops down 47μs after power ramps stop falling down. This behaviour is repeated for every transmission burst. AT# TXMONMODE? Note 1: The parameter is saved in NVM. Note 2: if user sets GPIO 5 as input or output the TXMON does not follow the above behaviour. Note 3: if is change during a call from 1 to 0, TXMON goes down. If it is restored to 1, TXMON behaves as usual, following the bursts. Note 4: this command is not supported in GM862 product family. Read command reports the parameter set value, in the format: AT#TXMONMODE=? #TXMONMOD: Test command reports the supported values for parameter. For example, if a call is started, the line will be HIGH during all the conversation and it will be again LOW after hanged up. The line rises up 300ms before first TX burst and will became again LOW from 500ms to 1sec after last TX burst. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 46 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 10.6 Using the Alarm Output GPIO6 The GPIO6 pad, when configured as Alarm Output, is controlled by the GE864-AUTO module and will rise when the alarm starts and fall after the issue of a dedicated AT command. This output can be used to power up the GE864-AUTO controlling microcontroller or application at the alarm time, giving you the possibility to program a timely system wake-up to achieve some periodic actions and completely turn off either the application and the GE864-AUTO during sleep periods, dramatically reducing the sleep consumption to few μA. In battery-powered devices this feature will greatly improve the autonomy of the device. NOTE: During RESET the line is set to HIGH logic level. 10.7 Using the Buzzer Output GPIO7 The GPIO7 pad, when configured as Buzzer Output, is controlled by the GE864-AUTO module and will drive with appropriate square waves a Buzzer driver. This permits to your application to easily implement Buzzer feature with ringing tones or melody played at the call incoming, tone playing on SMS incoming or simply playing a tone or melody when needed by your application. A sample interface scheme is included below to give you an idea of how to interface a Buzzer to the GPIO7: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 47 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 NOTE: To correctly drive a buzzer a driver must be provided, its characteristics depend on the Buzzer and for them refer to your buzzer vendor. 10.8 Indication of network service availability The STAT_LED pin status shows information on the network service availability and Call status. In the GE864-AUTO modules, the STAT_LED usually needs an external transistor to drive an external LED. Therefore, the status indicated in the following table is reversed with respect to the pin status. LED status Device Status Permanently off Device off Fast blinking (Period 1s, Ton 0,5s) Slow blinking (Period 3s, Ton 0,3s) Permanently on Net search / Not registered / turning off Registered full service a call is active Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 48 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 10.9 RTC Bypass out The VRTC pin brings out the Real Time Clock supply, which is separate from the rest of the digital part, allowing having only RTC going on when all the other parts of the device are off. To this power output a backup capacitor can be added in order to increase the RTC autonomy during power off of the battery. NO Devices must be powered from this pin. 10.10 External 32KHz oscillator The GE864-AUTO has an internal 32.768 KHz oscillator for ‘power saving’ and ‘Real Time Clock’ features. A common 32.768 KHz crystal is not reliable for ‘automotive’ applications. For this reason, the GE864 AUTO will not have an internal oscillator, but the 32.768 KHz signal must be fed in externally (ball F3). SQUARE WAVE 32.768KHz 32K_IN ball F3 GE864 AUTO This signal must be a square wave with following specifications: L-input voltage H-input voltage Input impedence Minimum -0.25 1.8 Maximum +0.2 2.2 > 10K Unit Ω If ‘power saving’ and ‘Real Time Clock’ features are not required, the signal 32K_IN (ball F3) must be connected to ground. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 49 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 A possible Clock Oscillator is shown in figure: VDD VDD CLKOE MICRO CR YSTAL OV-7604-C7 Low Power Clock Oscillator 32.768KHz CLKOUT 32K_IN ball F3 GE864 AUTO GND The Clock Oscillator should be placed close to GE864-AUTO. The AT command used to test the presence and the status of an external 32KHz oscillator is #OSC32KHZ Refer to SW User Guide or AT Commands Reference Guide for the full description of this function. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 50 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 11 ADC section 11.1 ADC Converter 11.1.1 Description The on board A/D are 11-bit converter. They are able to read a voltage level in the range of 0÷2 volts applied on the ADC pin input, store and convert it into 11 bit word. Input Voltage range AD conversion Resolution 0÷2 11 Volt bits mV The GE864-AUTO module provides 3 Analog to Digital Converters. The input lines are: ADC_IN1 available on Ball J11 and Pin 19 of PL102 on EVK2 Board (CS1302). ADC_IN2 available on Ball H11 and Pin 20 of PL102 on EVK2 Board (CS1302). ADC_IN3 available on Ball G11 and Pin 21 of PL102 on EVK2 Board (CS1302). 11.1.2 Using ADC Converter An AT command is available to use the ADC function. The command is AT#ADC=1,2 The read value is expressed in mV Refer to SW User Guide or AT Commands Reference Guide for the full description of this function. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 51 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 11.2 Mounting the GE864-AUTO on your Board 11.2.1 General The Telit GE864-AUTO modules have been designed in order to be compliant with a standard lead-free SMT process. 11.2.2 Module finishing & dimensions Pin A1 Lead-free Alloy: Surface finishing Sn/Ag/Cu for all solder pads Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 52 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 11.2.3 Recommended foot print for the application (GE864) Top View Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 53 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 11.2.4 Debug of the GE864 in production To test and debug the mounting of the GE864, we strongly recommend to foreseen test pads on the host PCB, in order to check the connection between the GE864 itself and the application and to test the performance of the module connecting it with an external computer. Depending by the customer application, these pads include, but are not limited to the following signals: • TXD • RXD • ON/OFF • RESET • GND • VBATT • TX_TRACE • RX_TRACE • PWRMON 11.2.5 Stencil Stencil’s apertures layout can be the same of the recommended footprint (1:1), we suggest a thickness of stencil foil ≥ 120µm. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 54 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 11.2.6 PCB pad design Non solder mask defined” (NSMD) type is recommended for the solder pads on the PCB. Recommendations for PCB pad dimensions Ball pitch [mm] Solder resist opening diameter A [mm] Metal pad diameter B [mm] 2,5 1,150 1 ± 0.05 Placement of microvias not covered by solder resist is not recommended inside the “Solder resist opening”, unless the microvia carry the same signal of the pad itself. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 55 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 Holes in pad are allowed only for blind holes and not for through holes. Recommendations for PCB pad surfaces: Finish Layer thickness [µm] Electro-less Ni / 3 –7 / Immersion Au 0.05 – 0.15 Properties good solder ability protection, high shear force values The PCB must be able to resist the higher temperatures which are occurring at the lead-free process. This issue should be discussed with the PCB-supplier. Generally, the wettability of tin-lead solder paste on the described surface plating is better compared to lead-free solder paste. 11.2.7 Solder paste Solder paste Lead free Sn/Ag/Cu Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 56 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 11.2.8 GE864 Solder reflow The following is the recommended solder reflow profile Profile Feature Average ramp-up rate (TL to TP) Preheat – Temperature Min (Tsmin) – Temperature Max (Tsmax) – Time (min to max) (ts) Tsmax to TL – Ramp-up Rate Time maintained above: – Temperature (TL) – Time (tL) Peak Temperature (Tp) Time within 5°C of actual Peak Temperature (tp) Ramp-down Rate Time 25°C to Peak Temperature Pb-Free Assembly 3°C/second max 150°C 200°C 60-180 seconds 3°C/second max 217°C 60-150 seconds 245 +0/-5°C 10-30 seconds 6°C/second max. 8 minutes max. NOTE: All temperatures refer to topside of the package, measured on the package body surface. NOTE: GE864 module can accept only one reflow process Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 57 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 11.3 Packing system The Telit GE864 modules are packaged on trays of 20 pieces each. This is especially suitable for the GE864 according to SMT processes for pick & place movement requirements. Section A-A The size of the tray is: 329 x 176mm NOTE: These trays can withstand at the maximum temperature of 65° C. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 58 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 11.3.1 GE864 orientation on the tray 11.3.2 Moisture sensibility The level of moisture sensibility of GE864 module is “3”, in according with standard IPC/JEDEC J-STD020, take care all the relatives requirements for using this kind of components. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 59 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 12 Conformity Assessment Issues The GE864-AUTO module is assessed to be conform to the R&TTE Directive as stand-alone products, so If the module is installed in conformance with Dai Telecom installation instructions require no further evaluation under Article 3.2 of the R&TTE Directive and do not require further involvement of a R&TTE Directive Notified Body for the final product. In all other cases, or if the manufacturer of the final product is in doubt then the equipment integrating the radio module must be assessed against Article 3.2 of the R&TTE Directive. In all cases assessment of the final product must be made against the Essential requirements of the R&TTE Directive Articles 3.1(a) and (b), safety and EMC respectively, and any relevant Article 3.3 requirements. The GE864-AUTO module is conform with the following European Union Directives: • R&TTE Directive 1999/5/EC (Radio Equipment & Telecommunications Terminal Equipments) • Low Voltage Directive 73/23/EEC and product safety • Directive 89/336/EEC for conformity for EMC In order to satisfy the essential requisite of the R&TTE 99/5/EC directive, the GE864-AUTO module is compliant with the following standards: • • • GSM (Radio Spectrum). Standard: EN 301 511 and 3GPP 51.010-1 EMC (Electromagnetic Compatibility). Standards: EN 301 489-1 and EN 301 489-7 LVD (Low Voltage Directive) Standards: EN 60 950 In this document and the Hardware User Guide, Software User Guide all the information you may need for developing a product meeting the R&TTE Directive is included. The GE864-AUTO module is conform with the following US Directives: • Use of RF Spectrum. Standards: FCC 47 Part 24 (GSM 1900) • EMC (Electromagnetic Compatibility). Standards: FCC47 Part 15 To meet the FCC's RF exposure rules and regulations: - The system antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all the persons and must not be co-located or operating in conjunction with any other antenna or transmitter. - The system antenna(s) used for this module must not exceed 3 dBi for mobile and fixed or mobile operating configurations. - Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and to have their complete product tested and approved for FCC compliance. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 60 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 13 SAFETY RECOMMANDATIONS READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc Where there is risk of explosion such as gasoline stations, oil refineries, etc It is responsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode. The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information’s are available on the European Community website: http://europa.eu.int/comm/enterprise/rtte/dir99-5.htm The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at: http://europa.eu.int/comm/enterprise/electr_equipment/index_en.htm Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 61 of 62 GE864-AUTO Hardware User Guide 1vv0300779 Rev.0 - 20/06/08 14 Document Change Log Revision Date Changes ISSUE#0 20/06/08 Release First ISSUE# 0 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 62 of 62
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Creator Tool : Acrobat PDFMaker 8.1 for Word Modify Date : 2008:06:25 10:15:22+02:00 Create Date : 2008:06:25 10:14:46+02:00 Metadata Date : 2008:06:25 10:15:22+02:00 Producer : Acrobat Distiller 8.1.0 (Windows) Format : application/pdf Creator : F D Title : GE864 Harware User Guide Document ID : uuid:4ef51087-6456-43ae-bf85-94a84bb644f2 Instance ID : uuid:a45beaa2-7170-4f33-8ff0-e25d7b58183a Company : Telit Communications S.p.A. Page Count : 62 Page Layout : OneColumn Author : F DEXIF Metadata provided by EXIF.tools