Telit Communications S p A GE866 Wireless module User Manual 1VV0301051 GE866 QUAD Hardware User Guide r2

Download:
Mirror Download [FCC.gov]
Document ID	2260503
Application ID	GzgJFVgRM09uqjKfyyow4A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	78.77kB (984591 bits)
Date Submitted	2014-05-07 00:00:00
Date Available	2014-11-03 00:00:00
Creation Date	2014-04-11 14:05:14
Producing Software	GPL Ghostscript 8.70
Document Lastmod	2014-04-11 14:05:14
Document Title	1VV0301051_GE866-QUAD_Hardware_User_Guide_r2
Document Creator	PDFCreator Version 1.0.2
Document Author:	EmiliaIb

GE866-QUAD Hardware User
Guide
1VV0301051 Rev. 2 – 2014-04-07
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
APPLICABILITY TABLE
PRODUCT
GE866-QUAD
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 2 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Notice
While reasonable efforts have been made to assure the accuracy of this document, Telit
assumes no liability resulting from any inaccuracies or omissions in this document, or from
use of the information obtained herein. The information in this document has been carefully
checked and is believed to be entirely reliable. However, no responsibility is assumed for
inaccuracies or omissions. Telit reserves the right to make changes to any products described
herein and reserves the right to revise this document and to make changes from time to time
in content hereof with no obligation to notify any person of revisions or changes. Telit does
not assume any liability arising out of the application or use of any product, software, or
circuit described herein; neither does it convey license under its patent rights or the rights of
others.
It is possible that this publication may contain references to, or information about Telit
products (machines and programs), programming, or services that are not announced in your
country. Such references or information must not be construed to mean that Telit intends to
announce such Telit products, programming, or services in your country.
Copyrights
This instruction manual and the Telit products described in this instruction manual may be,
include or describe copyrighted Telit material, such as computer programs stored in
semiconductor memories or other media. Laws in the Italy and other countries preserve for
Telit and its licensors certain exclusive rights for copyrighted material, including the
exclusive right to copy, reproduce in any form, distribute and make derivative works of the
copyrighted material. Accordingly, any copyrighted material of Telit and its licensors
contained herein or in the Telit products described in this instruction manual may not be
copied, reproduced, distributed, merged or modified in any manner without the express
written permission of Telit. Furthermore, the purchase of Telit products shall not be deemed
to grant either directly or by implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Telit, as arises by operation of law in the sale of a
product.
Computer Software Copyrights
The Telit and 3rd Party supplied Software (SW) products described in this instruction manual
may include copyrighted Telit and other 3rd Party supplied computer programs stored in
semiconductor memories or other media. Laws in the Italy and other countries preserve for
Telit and other 3rd Party supplied SW certain exclusive rights for copyrighted computer
programs, including the exclusive right to copy or reproduce in any form the copyrighted
computer program. Accordingly, any copyrighted Telit or other 3rd Party supplied SW
computer programs contained in the Telit products described in this instruction manual may
not be copied (reverse engineered) or reproduced in any manner without the express written
permission of Telit or the 3rd Party SW supplier. Furthermore, the purchase of Telit products
shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any
license under the copyrights, patents or patent applications of Telit or other 3rd Party supplied
SW, except for the normal non-exclusive, royalty free license to use that arises by operation
of law in the sale of a product.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 3 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Usage and Disclosure Restrictions
License Agreements
The software described in this document is the property of Telit and its licensors. It is
furnished by express license agreement only and may be used only in accordance with the
terms of such an agreement.
Copyrighted Materials
Software and documentation are copyrighted materials. Making unauthorized copies is
prohibited by law. No part of the software or documentation may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language or computer language,
in any form or by any means, without prior written permission of Telit
High Risk Materials
Components, units, or third-party products used in the product described herein are NOT
fault-tolerant and are NOT designed, manufactured, or intended for use as on-line control
equipment in the following hazardous environments requiring fail-safe controls: the operation
of Nuclear Facilities, Aircraft Navigation or Aircraft Communication Systems, Air Traffic
Control, Life Support, or Weapons Systems (High Risk Activities"). Telit and its supplier(s)
specifically disclaim any expressed or implied warranty of fitness for such High Risk
Activities.
Trademarks
TELIT and the Stylized T Logo are registered in Trademark Office. All other product or
service names are the property of their respective owners.
Copyright © Telit Communications S.p.A. 2014
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 4 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Contents
1.
Introduction ................................................. 8
1.1.
Scope ..................................................... 8
1.2.
Audience .................................................. 8
1.3.
Contact Information, Support .............................. 8
1.4.
Document Organization ..................................... 9
1.5.
Text Conventions ......................................... 10
1.6.
Related Documents ........................................ 10
2.
Overview .................................................... 11
3.
GE866-QUAD Mechanical Dimensions ............................ 12
4.
GE866-QUAD module connections ............................... 13
4.1.
PIN-OUT .................................................. 13
4.2.
Pin Layout ............................................... 16
5.
Hardware Commands ........................................... 17
5.1.
Auto-Turning ON the GE866-QUAD ........................... 17
5.2.
Turning OFF the GE866-QUAD ............................... 19
5.3.
Resetting the GE866-QUAD ................................. 21
5.3.1.
6.
Hardware Unconditional restart ............................. 21
Power Supply ................................................ 24
6.1.
Power Supply Requirements ................................ 24
6.2.
Power Consumption ........................................ 26
6.3.
General Design Rules ..................................... 27
6.3.1.
6.3.2.
6.3.3.
7.
Electrical Design Guidelines ............................... 27
Thermal Design Guidelines .................................. 30
Power Supply PCB layout Guidelines ......................... 32
Antenna ..................................................... 34
7.1.
GSM Antenna Requirements ................................. 34
7.1.1.
7.2.
GE866-QUAD Antenna – PCB line Guidelines ................... 34
PCB Design Guidelines .................................... 37
7.2.1.
7.2.2.
Transmission line design ................................... 37
Transmission line measurements ............................. 38
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 5 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
7.3.
8.
Logic levels specifications ................................. 40
8.1.
9.
GSM Antenna - installation Guidelines .................... 39
Reset signal ............................................. 41
Serial Ports ................................................ 43
9.1.
Modem Serial Port ........................................ 43
9.2.
RS232 levels translation ................................. 46
10. Audio Section Overview ...................................... 48
10.1.
MIC Connection ......................................... 48
10.2.
EAR Connection ......................................... 48
10.3.
Electrical Characteristics ............................. 50
10.3.1.
10.3.2.
Input lines .............................................. 50
Output lines ............................................. 51
11. General Purpose I/O ......................................... 52
11.1.
GPIO Logic Levels ...................................... 53
11.2.
Using a GPIO Pad as INPUT .............................. 54
11.3.
Using a GPIO Pad as OUTPUT ............................. 54
11.4.
Using the RF Transmission Control GPIO4 ................ 54
11.5.
Using the RFTXMON Output GPIO5 ......................... 55
11.6.
Using the ALARM/BUZZER output GPIO6 .................... 55
11.7.
Magnetic Buzzer Concepts ............................... 57
11.7.1.
11.7.2.
11.7.3.
11.7.4.
Short Description ........................................
Frequency Behaviour ......................................
Power Supply Influence ...................................
Working Current Influence ................................
57
58
58
58
11.8.
STAT LED Indication of network service availability .... 59
11.9.
SIMIN detect function .................................. 60
11.10.
RTC Bypass out ......................................... 60
11.11.
SIM Holder Implementation .............................. 60
12. DAC and ADC section ......................................... 61
12.1.
DAC Converter .......................................... 61
12.1.1.
12.1.2.
Description .............................................. 61
Enabling DAC ............................................. 61
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 6 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
12.1.3.
12.2.
Low Pass Filter Example .................................. 62
ADC Converter .......................................... 62
12.2.1.
12.2.2.
Description .............................................. 62
Using ADC Converter ...................................... 63
13. Mounting the GE866 on your Board ............................ 64
13.1.
General ................................................ 64
13.2.
Module finishing & dimensions .......................... 64
13.3.
mm):
Recommended foot print for the application (dimensions in
65
13.4.
Stencil ................................................ 66
13.5.
PCB pad design ......................................... 66
13.6.
Recommendations for PCB pad dimensions (mm): ........... 67
13.7.
Solder paste ........................................... 69
13.8.
GE866 Solder reflow .................................... 70
14. Packing system .............................................. 72
14.1.
Packing on reel ........................................ 72
14.2.
Packing on tray ........................................ 73
14.3.
Moisture sensibility ................................... 74
15.
Conformity Assessment Issues ...................................... 75
15.1.
GE866-QUAD ............................................. 77
16. Safety Recommendations ...................................... 81
17. Document History ............................................ 82
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 7 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
1.
1.1.
Introduction
Scope
The aim of this document is the description of some hardware
solutions useful for developing a product with the Telit
GE866-QUAD module.
1.2.
Audience
This document is intended for Telit customers, who are
integrators, about to implement their applications using our
GE866-QUAD modules.
1.3.
Contact Information, Support
For
general
contact,
technical
documentation errors and to order
Technical Support Center (TTSC) at:
support,
to
report
manuals, contact Telit
TS-EMEA@telit.com
TS-NORTHAMERICA@telit.com
TS-LATINAMERICA@telit.com
TS-APAC@telit.com
Alternatively, use:
http://www.telit.com/en/products/technical-supportcenter/contact.php
For detailed information about where you can buy the Telit
modules or for recommendations on accessories and components
visit:
http://www.telit.com
To register for product news and announcements or for product
questions contact Telit Technical Support Center (TTSC).
Our aim is to make this guide as helpful as possible. Keep us
informed of your comments and suggestions for improvements.
Telit appreciates feedback from the users of our information.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 8 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
1.4.
Document Organization
This document contains the following chapters:
Chapter 1: “Introduction” provides a scope for this document,
target audience, contact and support information, and text
conventions.
Chapter 2: “Overview” provides an overview of the document.
Chapter 3: “GE866-QUAD Mechanical Dimensions”
Chapter 4: “GE866-QUAD Module Connections” deals with the pin
out configuration and layout.
Chapter 5: “Hardware Commands” How to operate on the module
via hardware.
Chapter 6: “Power supply”
general design rules.
Power
supply
requirements
and
Chapter 7: “Antenna” The antenna connection and board layout
design are the most important parts in the full product
design.
Chapter 8: “Logic Level specifications” Specific values
adopted in the implementation of logic levels for this module.
Chapter 9: “Serial ports” The serial port on the Telit GE866QUAD is the core of the interface between the module and OEM
hardware
Chapter 10: “Audio Section overview” Refers to the audio
blocks of the Base Band Chip of the GE866-QUAD Telit Modules.
Chapter 11: “General Purpose I/O” How the general purpose I/O
pads can be configured.
Chapter 12 “DAC and ADC Section” Deals with these two kind of
converters.
Chapter 13: “Mounting the GE866 on your Board” Recommendations
and specifics on how to mount the module on the user’s board.
Chapter 14: “Packing system” Recommendations and specifics on
how the system is packaged.
Chapter 15:
“Safety Recommendations”
specifics on how the system is packaged.
Chapter 16:
Recommendations
and
“Document History” Holds all document changes
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 9 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
1.5.
Text Conventions
Danger – This information MUST be followed or catastrophic
equipment failure or bodily injury may occur.
Caution or Warning – Alerts the user to important points about
integrating the module, if these points are not followed, the
module and end user equipment may fail or malfunction.
Tip or Information – Provides advice and suggestions that may
be useful when integrating the module.
All dates are in ISO 8601 format, i.e. YYYY-MM-DD.
1.6.
Related Documents
•
Telit GSM/GPRS Family Software User Guide, 1vv0300784
•
Audio settings application note , 80000NT10007a
•
Digital Voice Interface Application Note, 80000NT10004a
•
GE866-QUAD Product description, 80416ST10122A
•
SIM Holder Design Guides, 80000NT10001a
•
AT Commands Reference Guide, 80000ST10025a
•
Telit EVK2 User Guide, 1vv0300704
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 10 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
2.
Overview
The aim of this document is the description of some hardware
solutions useful for developing a product with the Telit
GE866-QUAD module.
In this document all the basic functions of a mobile phone
will be taken into account; for each one of them a proper
hardware solution will be suggested and eventually the wrong
solutions and common errors to be avoided will be evidenced.
Obviously this document cannot embrace all hardware solutions
and products that may be designed. Avoiding the wrong
solutions shall be considered as mandatory. While the
suggested hardware configurations shall not be considered
mandatory, the information given shall be used as a guide and
a starting point for properly developing your product with the
Telit GE866-QUAD module. For further hardware details that may
not be explained in this document refer to the Telit GE866QUAD Product Description document where all the hardware
information is reported.
NOTE:
The integration of the GSM/GPRS GE866-QUAD cellular module
within user application shall be done according to the design
rules described in this manual.
The information presented in this document is believed to be
accurate and reliable. However, no responsibility is assumed
by Telit Communications S.p.A. for its use, nor any
infringement of patents or other rights of third parties which
may result from its use. No license is granted by implication
or otherwise under any patent rights of Telit Communications
S.p.A. other than for circuitry embodied in Telit products.
This document is subject to change without notice.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 11 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
3.
GE866-QUAD Mechanical Dimensions
The GE866-QUAD overall dimensions are:
•
Length:
•
Width:
•
Thickness: 2.1 mm
•
Weight:
17.2 mm
13.2 mm
1.5 g
Figure 1
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 12 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
4.
4.1.
GE866-QUAD module connections
PIN-OUT
Pad
Signal
I/O
Function
Note
Type
E7
EAR-
AO
Earphone signal output, phase -
Audio
D7
EAR+
AO
Earphone signal output, phase +
Audio
G7
MIC-
AI
Mic. signal input; phase-
Audio
F7
MIC+
AI
Mic. signal input; phase+
Audio
F6
AGND
Analog Ground
Power
Audio
SIM card interface
C7
SIMVCC
External SIM signal – Power supply for the SIM
1,8 / 3V
B7
SIMRST
External SIM signal – Reset
1,8 / 3V
A7
SIMCLK
External SIM signal – Clock
A6
All GPI0
can be
program
med
SIMIO
I/O
External SIM signal – Data I/O
SIMIN
Presence SIM input
1,8 / 3V
4.7k Pull up
1,8 / 3V
CMOS 1.8V
Trace
C2
RXD_AUX
Auxiliary UART (RX Data)
CMOS 1.8V
C1
TXD_AUX
Auxiliary UART (TX Data)
CMOS 1.8V
A4
C103/TXD
Prog. / Data + HW Flow Control
Output for Data carrier detect signal (DCD) to DTE
/ GP output
Output for Ring indicator signal (RI) to DTE
/ GP output
Output for Data set ready signal (DSR) to DTE
/ GP output
Input for Data terminal ready signal (DTR) from DTE
/ GP input
Input for Request to send signal (RTS) from DTE
/ GP input
Output for Clear to send signal (CTS) to DTE
/ GP output
Serial data input (TXD) from DTE
A5
C104/RXD
Serial data output to DTE
B2
C109/DCD/GPO
B3
C125/RING/GPO
A3
C107/DSR/GPO
A2
C108/DTR/GPI
A1
C105/RTS/GPI
B1
C106/CTS/GPO
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
DAC and ADC
F4
ADC_IN
AI
Analog/Digital converter input
A/D
E4
DAC_OUT
AO
Digital/Analog converter output
D/A
Miscellaneous Functions
F5
VRTC
AO
VRTC Backup
G4
RESET*
Reset input
2.3V
Power
CMOS 1.8V
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 13 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Pad
Signal
I/O
G6
V_AUX / PWRMON
G2
Antenna
I/O
Function
1.8V stabilized output Imax=100mA
/ Power ON monitor
Antenna pad – 50 Ω
GPIO
GPIO01 Configurable GPIO
/ Digital Audio Interface (WA0)
GPIO02 I/O pin
/ Jammer Detect Report
/ Digital Audio Interface (RX)
GPIO03 GPIO I/O pin
/ Digital Audio Interface (TX)
GPIO04 Configurable GPIO
/ TX Disable input
/ Digital Audio Interface (CLK)
GPIO05 Configurable GPIO
/ Transmitter ON monitor
GPIO06 Configurable GPIO
/ ALARM
GPIO07 Configurable GPIO
/ Digital Audio Interface (CLK)
Power Supply
Note
Type
Power Out 1.8V
RF
C5
GPIO_01 / DVI_WA0
I/O
CMOS 1.8V
C6
GPIO_02 / JDR /
DVI_RX
I/O
D6
GPIO_03 / DVI_TX
I/O
D5
GPIO_04 / TX Disable
/ DVI_CLK
I/O
B5
GPIO_05 / RFTXMON
I/O
B4
GPIO_06 / ALARM /
BUZZER
I/O
C4
GPIO_07 / STAT_LED
I/O
E2
VBATT
Main power supply (Baseband)
E1
VBATT_PA
Main power supply (Radio PA)
Power
F6
AGND
AF Signal Ground (see audio section)
AF Signal
D1
GND
Ground
Power
F1
GND
Ground
Power
G1
GND
Ground
Power
D2
GND
Ground
Power
F2
GND
Ground
Power
C3
GND
Ground
Power
E3
GND
Ground
Power
F3
GND
Ground
Power
G3
GND
Ground
Power
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
Power
RESERVED
D3
D4
E5
G5
B6
E6
WARNING:
Reserved pins must not be connected.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 14 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
WARNING:
VAUX output must not be used to supply any device on the
customer application.
It is only provided as reference/supply voltage when voltage
translation to 1V8 CMOS is needed.
When its use is necessary, it is strongly recommended to
connect VAUX through a series resistor as closed as possible
to the module in order to reduce the inrush current of the
internal DC/DC supply. Use a low value resistor (e.g. 10 ohm,
1/3W) with a maximum power rating related to drained current.
NOTE:
If not used, almost all pins should be left disconnected. The
only exceptions are the following pins:
Pin
E2, E1
D1, F1, G1, D2, F2, C2,
E3, F3, G3
F6
A4
A5
A1
G6
G4
C1
C2
signal
VBATT & VBATT_PA
GND
AGND
TXD
RXD
RTS
V_AUX / PWRMON
RESET*
TXD_AUX
RXD_AUX
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 15 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
4.2.
Pin Layout
TOP VIEW
C105/RTS
C106/CTS
TXD_AUX
GND
VABTT_PA
GND
GND
C108/DTR
C109/DCD
RXD_AUX
GND
VABTT
GND
ANT
C107/DSR C125/RING
GND
RESERVED
GND
GND
GND
C103/TXD
GPIO_06/
ALRM/
BUZZER
GPIO_07/
STAT_LED
RESERVED
DAC_OUT
ADC_IN
RESET*
C104/RXD
GPIO_05/
RFTXMON
GPIO_01/
DVI_WAO
GPIO_04/
TX_DIS/
DVI_CLK
RESERVED
VRTC
RESERVED
SIMIO
RESERVED
GPIO_02/
JDR/
DVI_RX
GPIO_03/
DVI_TX
RESERVED
AGND
V_AUX/
PWRMON
SIMCLK
SIMRST
SIMVCC
EAR+
EAR-
MIC+
MIC-
AUDIO
SIM
MISCELLANOUS
SERIAL
GPIO
ANTENNA
RESERVED/FU
POWER
GND
NOTE:
The pins defined RESERVED must not be connected to any pin in
the application.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 16 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
5.
5.1.
Hardware Commands
Auto-Turning ON the GE866-QUAD
To Auto-turn on the GE866-QUAD, the power supply must be
applied on the power pins VBATT and VBATT_PA, after 1000 mseconds, the V_AUX / PWRMON pin will be at the high logic
level and the module can be considered fully operating.
When the power supply voltage is between 3.22V and 3.4V, after
5000 m-seconds, the V_AUX / PWRMON pin will be at the high
logic level and the module can be considered fully operating.
The following flow chart shows the proper turn on procedure:
Modem ON Proc.
PWR supply = ON?
Delay 300mS
Enter AT
PWMON = ON?
AT answer in
1second ?
Delay 1s - 5s for Low
Voltage Operating
PWMON = ON?
AT init sequence.
Modem Reset Proc.
Delay 1s
Start AT CMD.
NOTE:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 17 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
The power supply must be applied either at the same time on
pins VBATT and VBATT_PA, or first applied on VBATT_PA and then
on VBATT. The opposite sequence shall be avoided. The reverse
procedure applies for powering down the module: first
disconnect VBATT, then VBATT_PA, or both at once.
NOTE:
In order to prevent
to avoid having any
digital pins of the
or during an ON/OFF
a back powering effect it is recommended
HIGH logic level signal applied to the
GE866-QUAD when the module is powered OFF
transition.
A flow chart showing the AT commands managing procedure is
displayed below:
Start AT CMD.
Delay 300mS
Enter AT
AT answer in
1second?
AT init sequence.
Disconnect PWR
supply
Modem ON Proc.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 18 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
5.2.
Turning OFF the GE866-QUAD
Turning off of the device can be done in two ways:
•
General turn OFF
•
Processor turn OFF
General turn OFF – disconnect the power supply from the both
power pins VBATT and VBATT_PA at the same time. In this case
all parts of the module are in OFF condition, no power
consumption is present.
Processor turn OFF – disconnect the power supply only from the
power pin VBATT, the power pin VBATT_PA can be connected to
power supply, in this case a low, about 30uA, power
consumption is present
Before either of both OFF procedures is applied, the
AT#SYSHALT AT command must be sent (see AT Commands Reference
Guide, 80000ST10025a), after the OK response message, wait for
10 seconds, then the module can be consider fully not
operating and at this moment is possible disconnect the Power
Supply.
The following flow chart shows the proper turnoff procedure:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 19 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Modem OFF
Proc.
AT#SYSHALT
10s timeout
Disconnect PWR
supply
Delay 1.5s
Modem ON Proc.
WARNING:
PWRMON can be used to monitor only the power on but it cannot
be used to monitor the power off because it remains high
NOTE:
In order to prevent
to avoid having any
digital pins of the
or during an ON/OFF
a back powering effect it is recommended
HIGH logic level signal applied to the
GE866-QUAD when the module is powered off
transition.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 20 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
5.3.
5.3.1.
Resetting the GE866-QUAD
Hardware Unconditional restart
WARNING:
The hardware unconditional Restart must not be used during
normal operation of the device since it does not detach the
device from the network. It shall be kept as an emergency exit
procedure to be done in the rare case that the device gets
stuck waiting for some network or SIM responses.
To unconditionally reboot the GE866-QUAD, the pad RESET* must
be tied low for at least 200 milliseconds and then released.
The maximum current that can be drained from the ON* pad is
0.15 mA.
NOTE:
Do not use any pull up resistor on the RESET* line nor any
totem pole digital output. Using pull up resistor may bring to
latch up problems on the GE866-QUAD power regulator and
improper functioning of the module. The line RESET* must be
connected only in open collector configuration; the transistor
must be connected as close as possible to the RESET* pin.
TIP:
The unconditional hardware restart must always be implemented
on the boards and the software must use it as an emergency
exit procedure.
A simple circuit to do it is:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 21 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
In the following flow chart is detailed the proper restart
procedure:
Modem Reset
Proc.
Reset = LOW
Delay 200ms
Reset = HIGH
Delay 1s
Start AT CMD.
NOTE:
In order to prevent a back powering effect it is recommended
to avoid having any HIGH logic level signal applied to the
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 22 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
digital pins of the GE866-QUAD when the module is powered OFF
or during an ON/OFF transition.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 23 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
6.
Power Supply
The power supply circuitry and board layout are a very
important part in the full product design and they strongly
reflect on the product overall performance, hence read the
requirements carefully and the guidelines that will follow for
a proper design.
6.1.
Power Supply Requirements
The external power supply must be connected to VBATT &
VBATT_PA signals and must fulfill the following requirements:
POWER SUPPLY
Nominal Supply Voltage
Normal Operating Voltage Range
Extended Operating Voltage Range
3.8 V
3.40 V÷ 4.20 V
3.10 V÷ 4.50 V
NOTE:
The Operating Voltage Range MUST never be exceeded; care must
be taken when designing the application’s power supply section
to avoid having an excessive voltage drop.
If the voltage drop is exceeding the limits it could cause a
Power Off of the module.
The Power supply must be higher than 3.22 V to power on the
module.
NOTE:
Overshoot voltage (regarding MAX Extended Operating Voltage)
and drop in voltage (regarding MIN Extended Operating Voltage)
MUST never be exceeded;
The “Extended Operating Voltage Range” can be used only with
complete assumption and application of the HW User guide
suggestions.
NOTE:
When the power supply voltage is between 3.22V and 3.4V, after
5000 m-seconds, the V_AUX / PWRMON pin will be at the high
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 24 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
logic level and the module can be consider fully operating.
See Par. 5.1.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 25 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
6.2.
Power Consumption
The GE866-QUAD preliminary power consumptions are:
GE866-QUAD
Mode
Average
(mA)
SWITCHED OFF
Switched Off
Switched Off with
AT#SYSHALT
IDLE mode
AT+CFUN=1
AT+CFUN=4
Typical 2uA
max 20uA
<500uA
AT+CFUN=0 or =5
CSD TX and RX mode
GSM900 CSD PL5
DCS1800 CSD PL0
GPRS (class 1) 1TX + 1RX
GSM900 PL5
DCS1800 PL0
GPRS (class 10) 2TX + 3RX
GSM900 PL5
DCS1800 PL0
Mode description
Module power supplied only on VBATT_PA pin, the VBATT pin
is not power supplied.
Module power supplied on VBATT_PA pin and VBATT pin, the
command AT#SYSHALT is applied.
1.7
1.5
1.3
0,8
Normal mode: full functionality of the module
Disabled TX and RX; module is not registered on the network
Paging Multiframe 2
Paging Multiframe 3
Paging Multiframe 4
Paging Multiframe 9
200
150
GSM VOICE CALL
200
140
GPRS Sending data mode
330
250
GPRS Sending data mode
The GSM system is made in a way that the RF transmission is
not continuous, but it is packed into bursts at a base
frequency of approx. 217 Hz, and the relative current peaks
can be as high as about 2A. Therefore the power supply has to
be designed to withstand these current peaks without big
voltage drops; this means that both the electrical design and
the board layout must be designed for this current flow.
If the layout of the PCB is not well designed a strong noise
floor is generated on the ground and the supply; this will
reflect on all the audio paths producing an audible annoying
noise at approx. 217 Hz; if the voltage drop during the peak
current absorption is too much, then the device may even
shutdown as a consequence of the supply voltage drop.
NOTE:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 26 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
The electrical design for the Power supply should be made
ensuring it will be capable of a peak current output of at
least 2 A.
6.3.
General Design Rules
The principal guidelines for the Power Supply Design embrace
three different design steps:
6.3.1.
•
The electrical design
•
The thermal design
•
Thermal PCB layout
Electrical Design Guidelines
The electrical design of the power supply depends strongly on
the power source from which this power is drained. We will
distinguish them into three categories:
6.3.1.1.
•
+5V input
•
+12V input (typically automotive)
•
Battery
(typically PC internal regulator output)
+ 5V input Source Power Supply Design Guidelines
•
The desired output for the power supply is 3.8V, hence
there's not a big difference between the input source and
the desired output and a linear regulator can be used. A
switching power supply will not be suited because of the
low drop out requirements.
•
When using a linear regulator, a proper heat sink shall be
provided in order to dissipate the power generated.
•
A Bypass low ESR capacitor of adequate capacity must be
provided in order to cut the current absorption peaks close
to the GE866-QUAD, a 100µF tantalum capacitor is usually
suited.
•
Make sure the low ESR capacitor on the power supply output
(usually a tantalum one) is rated at least 10V.
•
A protection diode should be inserted close to the power
input, in order to save the GE866-QUAD from power polarity
inversion.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 27 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
An example of linear regulator with 5V input is:
6.3.1.2.
12V input Source Power Supply Design Guidelines
•
The desired output for the power supply is 3.8V, hence due
to the big difference between the input source and the
desired output, a linear regulator is not suited and shall
not be used. A switching power supply will be preferable
because of its better efficiency especially with the 2A
peak current load represented by the GE866-QUAD.
•
When using a switching regulator, a 500kHz or more
switching frequency regulator is preferable because of its
smaller inductor size and its faster transient response.
This allows the regulator to respond quickly to the current
peaks absorption.
•
In any case the frequency and Switching design selection is
related to the application to be developed due to the fact
the switching frequency could also generate EMC
interferences.
•
For car PB battery the input voltage can rise up to 15,8V
and this should be kept in mind when choosing components:
all components in the power supply must withstand this
voltage.
•
A Bypass low ESR capacitor of adequate capacity must be
provided in order to cut the current absorption peaks, a
100µF tantalum capacitor is usually suited.
•
Make sure the low ESR capacitor on the power supply output
(usually a tantalum one) is rated at least 10V.
•
For Car applications a spike protection diode should be
inserted close to the power input, in order to clean the
supply from spikes.
•
A protection diode should be inserted close to the power
input, in order to save the GE866-QUAD from power polarity
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 28 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
inversion. This can be the same diode as for spike
protection.
An example of switching regulator with 12V input is in the
below schematic:
6.3.1.3.
Battery Source Power Supply Design Guidelines
•
The desired nominal output for the power supply is 3.8V and
the maximum voltage allowed is 4.2V, hence a single 3.7V
Li-Ion cell battery type is suited for supplying the power
to the Telit GE866-QUAD module.
WARNING:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 29 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
The three cells Ni/Cd or Ni/MH 3.6 V Nom. battery types or 4V
PB types MUST NOT BE USED DIRECTLY since their maximum voltage
can rise over the absolute maximum voltage for the GE866-QUAD
and damage it.
NOTE:
DON'T USE any Ni-Cd, Ni-MH, and Pb battery types directly
connected with GE866-QUAD. Their use can lead to overvoltage
on the GE866-QUAD and damage it. USE ONLY Li-Ion battery types.
6.3.2.
•
A Bypass low ESR capacitor of adequate capacity must be
provided in order to cut the current absorption peaks, a
100µF tantalum capacitor is usually suited.
•
Make sure the low ESR capacitor (usually a tantalum one) is
rated at least 10V.
•
A protection diode should be inserted close to the power
input, in order to save the GE866-QUAD from power polarity
inversion. Otherwise the battery connector should be done
in a way to avoid polarity inversions when connecting the
battery.
•
The battery capacity must be at least 500mAh in order to
withstand the current peaks of 2A; the suggested capacity
is from 500mAh to 1000mAh.
Thermal Design Guidelines
The thermal design for the power supply heat sink should be
done with the following specifications:
See Par. 6.2 Power Consumption
NOTE:
The average consumption during transmissions depends on the
power level at which the device is requested to transmit by
the network. The average current consumption hence varies
significantly.
Considering the very low current during idle, especially if
Power Saving function is enabled, it is possible to consider
from the thermal point of view that the device absorbs current
significantly only during calls.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 30 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
For the heat generated by the GE866-QUAD, you can consider it
to be during transmission 1W max during CSD/VOICE calls and 2W
max during class10 GPRS upload.
This generated heat will be mostly conducted to the ground
plane under the GE866-QUAD; you must ensure that your
application can dissipate it.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 31 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
6.3.3.
Power Supply PCB layout Guidelines
As seen on the electrical design guidelines the power supply
shall have a low ESR capacitor on the output to cut the
current peaks and a protection diode on the input to protect
the supply from spikes and polarity inversion. The placement
of these components is crucial for the correct working of the
circuitry. A misplaced component can be useless or can even
decrease the power supply performance.
•
The Bypass low ESR capacitor must be placed close to the
Telit GE866-QUAD power input pads or in the case the power
supply is a switching type it can be placed close to the
inductor to cut the ripple provided the PCB trace from the
capacitor to the GE866-QUAD is wide enough to ensure a
dropless connection even during the 2A current peaks.
•
The protection diode must be placed close
connector where the power source is drained.
•
The PCB traces from the input connector to the power
regulator IC must be wide enough to ensure no voltage drops
occur when the 2A current peaks are absorbed. Note that this
is not made in order to save power loss but especially to
avoid the voltage drops on the power line at the current
peaks frequency of approx. 217 Hz that will reflect on all
the components connected to that supply, introducing the
noise floor at the burst base frequency. For this reason
while a voltage drop of 300-400 mV may be acceptable from
the power loss point of view, the same voltage drop may not
be acceptable from the noise point of view. If your
application doesn't have audio interface but only uses the
data feature of the Telit GE866-QUAD, then this noise is not
so disturbing and power supply layout design can be more
forgiving.
•
The PCB traces to the GE866-QUAD and the Bypass capacitor
must be wide enough to ensure no significant voltage drops
occur when the 2A current peaks are absorbed. This is for
the same reason as previous point. Try to keep this trace as
short as possible.
•
The PCB traces connecting the Switching output to the
inductor and the switching diode must be kept as short as
possible by placing the inductor and the diode very close to
the power switching IC (only for switching power supply).
This is done in order to reduce the radiated field (noise)
at the switching frequency (100-500 kHz usually).
•
The use of a good common ground plane is suggested.
to
the
input
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 32 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
•
The placement of the power supply on the board should be
done in such a way to guarantee that the high current return
paths in the ground plane are not overlapped to any noise
sensitive circuitry as the microphone amplifier/buffer or
earphone amplifier.
•
The power supply input cables should be kept separate from
noise sensitive lines such as microphone/earphone cables.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 33 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
7.
Antenna
The antenna connection and board layout design are the most
important aspect in the full product design as they strongly
affect the product overall performance, hence read carefully
and follow the requirements and the guidelines for a proper
design.
7.1.
GSM Antenna Requirements
As suggested on the Product Description the antenna and
antenna transmission line on PCB for a Telit GE866-QUAD device
shall fulfill the following requirements:
ANTENNA REQUIREMENTS
Frequency range
Impedance
Input power
VSWR absolute max
VSWR recommended
824-894 MHz GSM850 band
880-960 MHz GSM900 band
1710-1885MHz DCS1800 band
1850-1990MHz PCS1900 band
50 Ohm
>2W
≤ 10:1 (limit to avoid permanent damage)
≤ 2:1 (limit to fulfill all regulatory requirements)
Furthermore if the devices are developed for the US market
and/or Canada market they shall comply to the FCC and/or IC
approval requirements:
Those devices are to be used only for mobile and fixed
application. The antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-Users
must be provided with transmitter operation conditions for
satisfying RF exposure compliance. OEM integrators must ensure
that the end user has no manual instructions to remove or
install the GE866-QUAD. Antennas used for those OEM modules
must not exceed 3dBi gain for mobile and fixed operating
configurations.
7.1.1.
GE866-QUAD Antenna – PCB line Guidelines
When using the Telit GE866-QUAD module, since there's no
antenna connector on the module, the antenna must be connected
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 34 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
to the GE866-QUAD through the PCB with the antenna pad (pin
G2).
WARNING:
High Frequency harmonics may still not be sufficiently
attenuated in the GE866’s small package. The suggested Pi
network, between antenna output of the module and antenna
connector on application board, is used to meet the standard
specifications.
In first designs its use is strongly recommended.
In the case that the antenna is not directly developed on the
same PCB, hence directly connected at the antenna pad of the
GE866-QUAD, then a PCB line is needed in order to connect with
it or with its connector.
This
transmission
requirements:
line
shall
fulfill
the
following
ANTENNA LINE ON PCB REQUIREMENTS
50 ohm
Impedance
0,3 dB
Max Attenuation
No coupling with other signals allowed
Cold End (Ground Plane) of antenna shall be equipotential to the
GE866-QUAD ground pins
This transmission line should be designed according to the
following guidelines:
•
Ensure that the antenna line impedance is 50 ohm;
•
Keep the antenna line on the PCB as short as possible, since
the antenna line loss shall be less than 0,3 dB;
•
Antenna line must have uniform characteristics,
cross section, avoid meanders and abrupt curves;
•
Keep, if possible, one layer of the PCB used only for the
Ground plane;
•
Surround (on the sides, over and under) the antenna line on
PCB with Ground, avoid having other signal tracks facing
directly the antenna line track;
constant
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 35 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
•
The ground around the antenna line on PCB has to be strictly
connected to the Ground Plane by placing vias every 2mm at
least;
•
Place EM noisy devices as far as possible from GE866-QUAD
antenna line;
•
Keep the antenna line far away from the GE866-QUAD power
supply lines;
•
If you have EM noisy devices around the PCB hosting the
GE866-QUAD, such as fast switching ICs, take care of the
shielding of the antenna line by burying it inside the
layers of PCB and surround it with Ground planes, or shield
it with a metal frame cover.
•
If you don't have EM noisy devices around the PCB of GE866QUAD, by using a micro strip on the superficial copper layer
for the antenna line, the line attenuation will be lower
than a buried one.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 36 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
7.2.
PCB Design Guidelines
This
section
explains
the
suggested
design
for
transmission line on the customer’s application board.
7.2.1.
the
Transmission line design
During the design of the GE866-QUAD interface board, the
placement of components has been chosen properly, in order to
keep the line length as short as possible, thus leading to
lowest power losses possible. A Grounded Coplanar Waveguide
(G-CPW) line has been chosen, since this kind of transmission
line ensures good impedance control and can be implemented in
an outer PCB layer as needed in this case. A SMA female
connector has been used to feed the line.
The interface board is realized on a FR4, 4-layers PCB.
Substrate material is characterized by relative permittivity
εr = 4.6 ± 0.4 @ 1 GHz, TanD= 0.019 ÷ 0.026 @ 1 GHz.
A characteristic impedance of nearly 50 Ω is achieved using
trace width = 1.1 mm, clearance from coplanar ground plane =
0.3 mm each side. The line uses reference ground plane on
layer 3, while copper is removed from layer 2 underneath the
line. Height of trace above ground plane is 1.335 mm.
Calculated characteristic impedance is 51.6 Ω, estimated line
loss is less than 0.1 dB. The line geometry is shown below:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 37 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
7.2.2.
Transmission line measurements
HP8753E VNA (Full-2-port calibration) has been used in this
measurement session. A calibrated coaxial cable has been
soldered at the pad corresponding to GE866-QUAD RF output; a
SMA connector has been soldered to the board in order to
characterize the losses of the transmission line including the
connector itself. During Return Loss / impedance measurements,
the transmission line has been terminated to 50 Ω load.
Return Loss plot of line under test is shown below:
Line input impedance (in Smith Chart format, once the line has
been terminated
figure:
to
50
Ω
load)
is
shown
in
the
following
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 38 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Insertion Loss of G-CPW line plus SMA connector is shown
below:
7.3.
GSM Antenna - installation Guidelines
•
Install the antenna in a place covered by the GSM signal.
•
Antenna shall not be installed inside metal cases
•
Antenna shall be installed
manufacturer instructions.
•
Ddd Installation should also take in account the R&TTE
requirements described in the “Conformity Assessment Issues”
chapter
also
according
to
antenna
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 39 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
8.
Logic levels specifications
Where not specifically stated, all the interface circuits work
at 1.8V CMOS logic levels. The following table shows the logic
level
specifications
used
in
the
GE866-QUAD
interface
circuits:
Parameter
Min
Max
Input level on any digital pin
(CMOS 1.8) when on
-0.3V
+2.1V
Level
Min
Max
Input high level
1.3V
1.9V
Input low level
Output high level
0V
1.6V
0V
0.35V
1.9V
0.2V
Output low level
Level
Typical
Output Current
1mA
Input Current
1uA
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 40 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
8.1.
Reset signal
Signal
Function
I/O
pin
RESET*
Phone reset
G4
RESET* is used to reset the GE866-QUAD. Whenever this signal
is pulled low, the GE866-QUAD is reset. When the device is
reset it stops any operation. After the release of the reset
GE866-QUAD is unconditionally shut down, without doing any
detach operation from the network where it is registered. This
behaviour is not a proper shut down because any GSM device is
requested to issue a detach request on turn off. For this
reason the Reset signal must not be used to normally shutting
down the device, but only as an emergency exit in the rare
case the device remains stuck waiting for some network
response.
The RESET* is internally controlled on start-up to achieve a
proper power-on reset sequence, so there's no need to control
this pin on start-up. It may only be used to reset a device
already on that is not responding to any command.
NOTE:
Do not use this signal to power OFF the GE866-QUAD. Use the
ON/OFF procedure to perform this function.
Signal
Min
Max
RESET* Input high
1.8V(NOTE1)
2.1V
RESET* Input low
0V
0.2V
(NOTE1) this signal is internally pulled up so the pin can be
left floating if not used.
If unused, this signal may be left unconnected. If used, then
it must always be connected with an open collector transistor,
to permit to the internal circuitry the power on reset and
under voltage lockout functions.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 41 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 42 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
9.
Serial Ports
The serial port on the GE866-QUAD is the core of the interface
between the module and OEM hardware.
2 serial ports are available on the module:
•
MODEM SERIAL PORT 1 (Main, ASC0)
•
MODEM SERIAL PORT 2 (Auxiliary, ASC1)
9.1.
Modem Serial Port
Several configurations can be designed for the serial port on
the OEM hardware, but the most common are:
•
RS232 PC com port
•
microcontroller UART @ 1.8V (Universal Asynchronous Receive
Transmit)
•
microcontroller UART @ 3V or other voltages different from
1.8V
•
microcontroller UART @ 5V or other voltages different from
1.8V
Depending from the type of serial port on the OEM hardware a
level translator circuit may be needed to make the system work.
The only configuration that doesn't need a level translation
is the 1.8V UART.
The serial port on the GE866-QUAD is a +1.8V UART with all the
8 RS232 signals. It differs from the PC-RS232 in the signal
polarity (RS232 is reversed) and levels. The levels for the
GE866-QUAD UART are the CMOS levels:
Parameter
Min
Max
Input level on any digital
pad when on
Input voltage on analog
pads when on
-0.3V
+2.1V
-0.3V
+2.1V
Level
Min
Max
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 43 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Input high level VIH
1.5V
1.9V
Input low level VIL
Output high level VOH
Output low level VOL
0V
1.6V
0V
0.35V
1.9V
0.2V
The signals of the GE866-QUAD serial port are:
RS232 Pin
Number
Signal
GE866-QUAD
Pad Number
Name
DCD - dcd_uart
B2
RXD - tx_uart
A5
TXD - rx_uart
A4
DTR - dtr_uart
A2
GND
D1, F1, G1, D2,
F2, C2, E3, F3,
G3
Ground
DSR - dsr_uart
A3
Data Set Ready
RTS - rts_uart
A1
Request to Send
CTS - cts_uart
B1
Clear to Send
RI - ri_uart
B3
Ring Indicator
Usage
Output from the GE866-QUAD that
indicates the carrier presence
Transmit line *see
Output transmit line of GE866Note
QUAD UART
Input receive of the GE866-QUAD
Receive line *see Note
UART
Input to the GE866-QUAD that
Data Terminal Ready
controls the DTE READY condition
Data Carrier Detect
Ground
Output from the GE866-QUAD that
indicates the module is ready
Input to the GE866-QUAD that
controls the Hardware flow control
Output from the GE866-QUAD that
controls the Hardware flow control
Output from the GE866-QUAD that
indicates the incoming call condition
NOTE:
According to V.24, RX/TX signal names are referred to the
application side, therefore on the GE866-QUAD side these
signal are on the opposite direction: TXD on the application
side will be connected to the receive line (here named TXD/
rx_uart ) of the GE866-QUAD serial port and vice versa for RX.
NOTE:
For a minimum implementation, only the TXD and RXD lines can
be connected, the other lines can be left open provided a
software flow control is implemented.
NOTE:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 44 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
In order to avoid a back powering effect it is recommended to
avoid having any HIGH logic level signal applied to the
digital pins of the GE866-QUAD when the module is powered off
or during an ON/OFF transition.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 45 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
9.2.
RS232 levels translation
In order to interface the GE866-QUAD with a PC com port or a
RS232
(EIA/TIA-232)
application
level
translator
is
required. This level translator must:
•
invert the electrical signal in both directions;
•
change the level from 0/1.8V to +15/-15V
Actually, the RS232 UART 16450, 16550, 16650 & 16750 chipsets
accept signals with lower levels on the RS232 side (EIA/TIA562), allowing a lower voltage-multiplying ratio on the level
translator. Note that the negative signal voltage must be less
than 0V and hence some sort of level translation is always
required.
The simplest way to translate the levels and invert the signal
is by using a single chip level translator. There are a
multitude of them, differing in the number of drivers and
receivers and in the levels (be sure to get a true RS232 level
translator not a RS485 or other standards).
By convention the driver is the level translator from the 01.8V UART to the RS232 level. The receiver is the translator
from the RS232 level to 0-1.8V UART.
In order to translate the whole set of control lines of the
UART you will need:
•
5 drivers
•
3 receivers
NOTE:
The digital input lines working at 1.8V CMOS have an absolute
maximum input voltage of 2.1V; therefore the level translator
IC shall not be powered by the +3.8V supply of the module.
Instead, it must be powered from a +1.8V (dedicated) power
supply.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 46 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
An example of RS232 level adaptation circuitry could be done
using a MAXIM transceiver (MAX218).
In this case the chipset is capable to translate directly from
0/1.8V to the RS232 levels (Example done on 4 signals only).
The RS232 serial port lines are usually connected to a DB9
connector with the following layout:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 47 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
10.
10.1.
Audio Section Overview
MIC Connection
The Base Band Chip of the GE866-QUAD provides one input for
audio to be transmitted (Uplink).
10.2.
EAR Connection
EAR+
DAC OUTPUT
EAR-
TELIT MODULE
The audio output of the GE866-QUAD is balanced, this is
helpful to double the level and to reject common mode (click
and pop are common mode and therefore rejected); furthermore
the output stage is class-D, so it can manage directly a
loudspeaker with electrical impedance of at least 8Ohm. This
stage is powered by switching from Vbatt to gnd at a frequency
ranging from 0.6 to 2MHz, so it has a good efficiency and thus
a big power budget 0.7W; being a class-D architecture, please
use some caution (see the NOTE below).
NOTE:
When the loudspeaker is connected with a long cable, an L-C
filter is recommended.
When the EAR+/- are feeding some electronic circuitry, an R-C
filter is recommended.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 48 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
TIP:
In order to get the maximum audio level at a given output
voltage level (dBspl/Vrms), the following breaking through
procedure can be used. Have the loudspeaker as close as you
can to the listener (this simplify also the echo cancelling);
choose the loudspeaker with the higher sensitivity (dBspl per
W); choose loudspeakers with the impedance close to the limit
(ex: 16 or 8 Ohm), in order to feed more power inside the
transducer (it increases the W/Vrms ratio). If this were not
enough, an external amplifier should be used.
WARNING:
This The audio output hardware of the GE866-QUAD is based on a
Class-D amplifier so any singled-end output configuration MUST
NOT BE USED, otherwise the presence of GSM buzzing and low
level audio performance will result.
DAC OUTPUT
TELIT MODULE
EAR+
EAR-
GND
L-C filtering for LOW impedance load.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 49 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
EAR+
DAC OUTPUT
EAR-
GND
TELIT MODULE
HiZ CIRCUITRY
R-C filtering for HIGH impedance load.
10.3.
Electrical Characteristics
10.3.1. Input lines
Microphone/Line-in path
Line Type
Differential
Coupling capacitor
≥ 100nF
Differential input resistance
50kΩ
Levels
To have 0 dBfs @1KHz (*)
Differential input voltage
MIC Gain = 0dB
290mVrms
MIC Gain = +6dB
145mVrms
MIC Gain = +12dB
72mVrms
MIC Gain = +18dB
36mVrms
MIC Gain = +24dB
18mVrms
MIC Gain = +30dB
9mVrms
MIC Gain = +36dB
4.5mVrms
MIC Gain = +42dB
2.25mVrms
(*)
0 dBfs in the network are +3.14 dBm0
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 50 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
10.3.2. Output lines
EAR/Line-out Output
Direct connection (VDC=1.7÷2.1V)
Differential line coupling
output load resistance
≥8Ω
signal bandwidth
max. differential output voltage
250÷3400Hz
(@ -3dB with default filter)
1120 mVpp @3.14dBm0 (*)
differential output voltage
550mVrms @0dBm0 (*)
volume increment
2dB per step
volume steps
0..10
(*)
in default
Attenuation = 0dB
condition:
Output
Volume
+20dB,
Output
TIP:
We suggest driving the load differentially; this kills all the
common mode noises (click and pop, for example), the output
swing will double (+6dB) and the big output coupling capacitor
will be avoided.
In order to get the maximum power output from the device, the
resistance of the tracks has to be negligible in comparison to
the load.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 51 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
11.
General Purpose I/O
The general purpose I/O pads can be configured to act in three
different ways:
•
input
•
output
•
alternate function (internally controlled)
Input pads can be read; they report the digital value (high or
low) present on the pad at the read time.
Output pads can only be written or queried and set the value
of the pad output.
An alternate function pad is internally controlled by the
GE866-QUAD firmware and acts depending on the function
implemented.
For Logic levels please refer to chapter 8.
The following table shows the available GPIO on the GE866QUAD.
Pin
Signal
I/O
Function
C5
GPIO_01
I/O
Configurable GPIO
C6
GPIO_02
I/O
Configurable GPIO
D6
GPIO_03
I/O
Configurable GPIO
D5
GPIO_04
I/O
Configurable GPIO
B5
GPIO_05
I/O
Configurable GPIO
B4
GPIO_06
I/O
Configurable GPIO
C4
GPIO_07
I/O
Configurable GPIO
Type
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
Input /
output
current
Default
State
ON_OFF
state
State
during
Reset
Note
1uA/1mA
INPUT
Alternate function
DVI_WA0
1uA/1mA
INPUT
Alternate function
JDR and DVI_RX
1uA/1mA
INPUT
1uA/1mA
INPUT
1uA/1mA
INPUT
1uA/1mA
INPUT
1uA/1mA
INPUT
Alternate function
DVI_TX
Alternate function
TX Disable and
DVI_TX
Alternate function
RFTXMON
Alternate function
ALARM / BUZZER
Alternate function
STAT_LED
WARNING:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 52 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
During power up the GPIOs may be subject to transient glitches.
Also the UART‘s control flow pins can be used as GPIO.
Pin
Signal
I/O
B2
GPO_A
Configurable GPO
B3
GPO_B
Configurable GPO
A3
GPO_C
Configurable GPO
A2
GPI_E
Configurable GPI
A1
GPI_F
Configurable GPI
B1
GPO_D
Configurable GPO
11.1.
Function
Type
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
CMOS
1.8V
Input /
output
current
Default
State
ON_OFF
state
State
during
Reset
1uA/1mA
INPUT
1uA/1mA
INPUT
1uA/1mA
INPUT
1uA/1mA
INPUT
1uA/1mA
INPUT
1uA/1mA
INPUT
Note
Alternate function
C109/DCD
Alternate function
C125/RING
Alternate function
C107/DSR
Alternate function
C108/DTR
Alternate function
C105/RTS
Alternate function
C106/CTS
GPIO Logic Levels
Where not specifically stated, all the interface circuits work
at 1.8V CMOS logic levels.
The following table shows the logic level specifications used
in the GE866-QUAD interface circuits:
Parameter
Input level on any digital pin
(CMOS 1.8) when on
Min
-0.3V
Max
+2.1V
Level
Min
Max
Input high level
1.5V
1.9V
Input low level
Output high level
Output low level
0V
1.6V
0V
0.35V
1.9V
0.2V
Level
Typical
Output Current
1mA
Input Current
1uA
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 53 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
11.2.
Using a GPIO Pad as INPUT
The GPIO pads, when used as inputs, can be connected to a
digital output of another device and report its status,
provided this device has interface levels compatible with the
1.8V CMOS levels of the GPIO.
If the digital output of the device to be connected with the
GPIO input pad has interface levels different from the 1.8V
CMOS, then it can be buffered with an open collector
transistor with a 47K pull up to 1.8V.
NOTE:
In order to avoid a back powering effect it is recommended to
avoid having any HIGH logic level signal applied to the
digital pins of the GE866-QUAD when the module is powered OFF
or during an ON/OFF transition.
TIP:
The V_AUX / PWRMON pin can be used for input pull up reference
or/and for ON monitoring.
11.3.
Using a GPIO Pad as OUTPUT
The GPIO pads, when used as outputs, can drive 1.8V CMOS
digital devices or compatible hardware. When set as outputs,
the pads have a push-pull output and therefore the pull-up
resistor may be omitted.
11.4.
Using the RF Transmission Control GPIO4
The GPIO4 pin, when configured as RF Transmission Control
Input, permits to disable the Transmitter when the GPIO is set
to Low by the application.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 54 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
In the design is necessary to add a resistor 47K pull up to
2.8V, this pull up must be switched off when the module is in
off condition.
11.5.
Using the RFTXMON Output GPIO5
The GPIO5 pin, when configured as RFTXMON Output, is
controlled by the GE866-QUAD module and will rise when the
transmitter is active and fall after the transmitter activity
is completed.
There are 2 different modes for this function:
1) Active during the Call:
For example, if a call is started, the line will be HIGH
during all the conversation and it will be again LOW after
hanged up.
The line rises up 300ms before first TX burst and will became
again LOW from 500ms to 1s after last TX burst.
2) Active during the TX activity
The GPIO is following the TX bursts
Please refer to the AT User interface manual for additional
information on how to enable this function.
11.6.
Using the ALARM/BUZZER output GPIO6
The GPIO6 has 2 alternate functions:
•
ALARM
•
BUZZER
The GPIO6 pad, when configured as Alarm Output, is controlled
by the GE866-QUAD module and will rise when the alarm starts
and fall after the issue of a dedicated AT command.
This output can be used to controlling
application at the alarm time.
microcontroller
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 55 of 82
Mod. 0805 2011-07 Rev.2
or
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
The GPIO6 pad, when configured as Buzzer Output, is controlled
by the GE866-QUAD module and will drive a Buzzer driver with
appropriate square waves.
This permits to your application to easily implement Buzzer
feature with ringing tones or melody played at the call
incoming, tone playing on SMS incoming or simply playing a
tone or melody when needed.
A sample interface scheme is included below to give you an
idea of how to interface a Buzzer to the GPIO6:
TR2
SMBT2907A
+V buzzer
R1
4,7K
D1
D1N4148
C1
33pF
R2
1K
GPIO7
TR1
BCR141W
NOTE:
To correctly drive a buzzer a driver must be provided, its
characteristics depend on the Buzzer and for them refer to
your buzzer vendor
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 56 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
11.7.
Magnetic Buzzer Concepts
11.7.1. Short Description
A magnetic Buzzer is a sound-generating device with a coil
located in the magnetic circuit consisting of a permanent
magnet, an iron core, a high permeable metal disk and a
vibrating diaphragm.
Drawing of the Magnetic Buzzer.
The disk and diaphragm are attracted to the core by the
magnetic field. When an oscillating signal is moved through
the coil, it produces a fluctuating magnetic field which
vibrates the diaphragm at the frequency of the drive signal.
Thus the sound is produced relative to the frequency applied.
Diaphragm movement.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 57 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
11.7.2. Frequency Behaviour
The frequency behavior represents the effectiveness of the
reproduction of the applied signals. Because performance is
related to a square driving waveform (whose amplitude varies
from 0V to Vpp), if you modify the waveform (e.g. from square
to sinus) the frequency response will change.
11.7.3. Power Supply Influence
Applying a signal whose amplitude is different from that
suggested
by
the
manufacturer,
the
performance
change
following the rule “if resonance frequency fo increases,
amplitude decreases”.
Because resonance frequency depends on acoustic design, by
lowering the amplitude of the driving signal the response
bandwidth tends to become narrow, and vice versa.
Summarizing:
Vpp ↑ 
 fo ↓
Vpp ↓

fo ↑
The risk is that the fo could easily fall outside of new
bandwidth; consequently the SPL could be much lower than the
expected.
WARNING:
It is very important to respect the sense of the applied
voltage: never apply to the "-" pin a voltage more positive
than the "+" pin: if this happens, the diaphragm vibrates in
the opposite direction with a high probability to be expelled
from its physical position. This damages the device
permanently.
11.7.4. Working Current Influence
In the component data sheet you will find the value of MAX
CURRENT: this represents the maximum average current that can
flow at nominal voltage without current limitation. In other
words it is not the peak current, which could be twice or
three times higher. If driving circuitry does not support
these peak values, the SPL will never reach the declared level
or the oscillations will stop.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 58 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
11.8.
STAT LED Indication of network service
availability
The STAT_LED pin status shows information
service availability and Call status.
on
the
network
In the GE866-QUAD modules, the STAT_LED usually
external transistor to drive an external LED.
needs
an
Therefore, the status indicated in the
reversed with respect to the pin status.
table
is
LED status
Permanently off
Fast blinking
(Period 1s, Ton 0,5s)
Slow blinking
(Period 3s, Ton 0,3s)
Permanently on
following
Device Status
Device off
Net search / Not registered /
turning off
Registered full service
a call is active
A schematic example could be:
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 59 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
11.9.
SIMIN detect function
All the GPIO pins can be used as SIM DETECT input. The AT
Command used to enable the function is:
AT#SIMINCFG
Use the AT command AT#SIMDET=2 to enable the SIMIN detection
Use the AT command AT&W0 and
detection in the common profile.
For
full
details
80000ST10025a.
see
AT
AT&P0
to
Commands
store
the
Reference
SIMIN
Guide,
NOTE:
Don’t use the SIM IN function on the same pin where the GPIO
function is enabled and vice versa!
11.10. RTC Bypass out
The VRTC pin brings out the Real Time Clock supply, which is
separate from the rest of the digital part, allowing having
only RTC going on when all the other parts of the device are
off.
To this power output a backup battery can be added in order to
increase the RTC autonomy during power off of the main battery
(power supply). NO Devices must be powered from this pin.
11.11. SIM Holder Implementation
Please refer to the related User Guide (SIM Holder Design
Guides, 80000NT10001a).
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 60 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
12.
12.1.
DAC and ADC section
DAC Converter
12.1.1. Description
The GE866-QUAD provides a Digital to Analog Converter. The
signal (named DAC_OUT) is available on pin E4 of the GE866QUAD.
The on board DAC is a 10 bit converter, able to generate an
analogue value based on a specific input in the range from 0
up to 1023. However, an external low-pass filter is necessary
Voltage range (filtered)
Range
Min
Max
1.8
1023
Units
Volt
Steps
The precision is 10 bits so, if we consider that the maximum
voltage is 2V, the integrated voltage could be calculated with
the following formula:
Integrated output voltage = (2 *value) / 1023
DAC_OUT line must be integrated (for example with a low band
pass filter) in order to obtain an analog voltage.
12.1.2. Enabling DAC
An AT command is available to use the DAC function.
The command is:
AT#DAC= [ [, ]]
 - scale factor of the integrated output voltage
(0..1023 - 10 bit precision)
it must be present if
=1
Refer to SW User Guide or AT Commands Reference Guide for the
full description of this function.
NOTE:
The DAC frequency is selected internally. D/A converter must
not be used during POWERSAVING.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 61 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
12.1.3. Low Pass Filter Example
12.2.
ADC Converter
12.2.1. Description
The on board A/D converter is a 11-bit converter. It’s able to
read a voltage level in the range of 0÷2 volts applied on the
ADC pin input, store and convert it into 11 bit word.
Min
Input Voltage range
AD conversion
Resolution
The
GE866-QUAD
Converters.
module
Max
1.2
10
>1
provides
Units
Volt
bits
mV
one
Analog
to
Digital
The input line is:
ADC_IN
Available on pin F4
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 62 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
12.2.2. Using ADC Converter
An AT command is available to use the ADC function.
The command is AT#ADC=1,2
The read value is expressed in mV
Refer to SW User Guide or AT Commands Reference Guide for the
full description of this function.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 63 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
13.
13.1.
Mounting the GE866 on your Board
General
The GE866 modules have been designed in order to be compliant
with a standard lead-free SMT process.
13.2.
Module finishing & dimensions
Surface finishing Ni/Au for all solder pads
Dimensions in mm
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 64 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
13.3.
Recommended foot print for the
application (dimensions in mm):
Top View
In order to easily rework the GE866 is suggested to consider
on the application a 1.5 mm placement inhibit area around the
module.
It is also suggested, as common rule for an SMT component, to
avoid having a mechanical part of the application in direct
contact with the module.
NOTE:
In the customer application, the region under WIRING INHIBIT
(see figure above) must be clear from signal or ground paths.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 65 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
13.4.
Stencil
Stencil’s apertures layout can be the same of the recommended
footprint (1:1), we suggest a thickness of stencil foil ≥ 120
µm.
13.5.
PCB pad design
Non solder mask defined (NSMD) type is recommended for the
solder pads on the PCB.
Copper Pad
Pad
Solder Mask
PCB
SMD
(Solder Mask Defined)
NSMD
(Non Solder Mask Defined)
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 66 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
13.6.
Recommendations for PCB pad dimensions
(mm):
Solder resist openings
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 67 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
It is not recommended to place via or micro-via not covered by
solder resist in an area of 0,3 mm around the pads unless it
carries the same signal of the pad itself (see following
figure).
Inhibit area for micro-via
Holes in pad are allowed only for blind holes and not for
through holes.
Recommendations for PCB pad surfaces:
Finish
Electro-less Ni /
Immersion Au
Layer thickness [µm]
Properties
3 –7 / 0.05 – 0.15
good solder ability
protection,
high shear force values
The PCB must be able to resist the higher temperatures which
are occurring at the lead-free process. This issue should be
discussed with the PCB-supplier. Generally, the wettability of
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 68 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
tin-lead solder paste on the described surface
better compared to lead-free solder paste.
plating
is
It is not necessary to panel the application PCB, however in
that case it is suggested to use milled contours and
predrilled board breakouts; scoring or v-cut solutions are not
recommended.
13.7.
Solder paste
Lead free
Solder paste
Sn/Ag/Cu
We recommend using only “no clean” solder paste in order to
avoid the cleaning of the modules after assembly.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 69 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
13.8.
GE866 Solder reflow
Recommended solder reflow profile
Profile Feature
Average
TP)
ramp-up
Pb-Free Assembly
rate
(TL
to 3°C/second max
Preheat
– Temperature Min (Tsmin)
150°C
– Temperature Max (Tsmax)
200°C
– Time (min to max) (ts)
60-180 seconds
Tsmax to TL
– Ramp-up Rate
3°C/second max
Time maintained above:
– Temperature (TL)
217°C
– Time (tL)
60-150 seconds
Peak Temperature (Tp)
245 +0/-5°C
Time
within
5°C
of
actual 10-30 seconds
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 70 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Peak
Temperature (tp)
Ramp-down Rate
6°C/second max.
Time 25°C to Peak Temperature
8 minutes max.
NOTE:
All temperatures refer to topside of the package, measured on
the package body surface
WARNING:
The GE866 module withstands one reflow process only.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 71 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
14.
14.1.
Packing system
Packing on reel
The GE866 modules are packaged on reels of 500 pieces each
(TBC).
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 72 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
14.2.
Packing on tray
The GE866 modules are packaged on trays of 50 pieces each when
small quantities are required (i.e. for test and evaluation
purposes). Trays are not designed to be used in SMT processes
for pick and place handling.
WARNING:
These trays can withstand at the maximum temperature of 65° C.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 73 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
14.3.
Moisture sensibility
The moisture sensitivity level of the Product is “3” according with
standard IPC/JEDEC J-STD-020, take care of all the relative requirements
for using this kind of components.
Moreover, the customer has to take care of the following conditions:
a) The shelf life of the Product inside of the dry bag is 12 months from
the bag seal date, when stored in a non-condensing atmospheric
environment of < 40°C and < 90% RH.
b) Environmental condition during the production: <= 30°C / 60% RH
according to IPC/JEDEC J-STD-033B.
c) The maximum time between the opening of the sealed bag and the reflow
process must be 168 hours if condition b) “IPC/JEDEC J-STD-033B paragraph
5.2” is respected.
d) Baking is required if conditions b) or c) are not respected
e) Baking is required if the humidity indicator inside the bag indicates
10% RH or more.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 74 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
15.
Conformity Assessment Issues
European Union - Directive 1999/5/EC
The GE866 QUAD complies with the essential requirements of the 1999/5/EC Directive.
Bulgarian
Czech
Danish
Dutch
English
Estonian
German
Greek
Hungarian
Finnish
French
Icelandic
Italian
Latvian
С настоящето Telit Communications S.p.A. декларира, че Dual Band GSM/GPRS module
отговаря на съществените изисквания и другите приложими изисквания на Директива
1999/5/ЕС.
Telit Communications S.p.A. tímto prohlašuje, že tento Dual Band GSM/GPRS module je ve
shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Undertegnede Telit Communications S.p.A. erklærer herved, at følgende udstyr Dual Band
GSM/GPRS module overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
Hierbij verklaart Telit Communications S.p.A. dat het toestel Dual Band GSM/GPRS
module in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van
richtlijn 1999/5/EG.
Hereby, Telit Communications S.p.A., declares that this Dual Band GSM/GPRS module is in
compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC.
Käesolevaga kinnitab Telit Communications S.p.A. seadme Dual Band GSM/GPRS module
vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele
asjakohastele sätetele.
Hiermit erklärt Telit Communications S.p.A., dass sich das Gerät Dual Band GSM/GPRS
module in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Telit Communications S.p.A. ∆ΗΛΩΝΕΙ ΟΤΙ Dual Band GSM/GPRS
module ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.
Alulírott, Telit Communications S.p.A. nyilatkozom, hogy a Dual Band GSM/GPRS module
megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb
elõírásainak.
Telit Communications S.p.A. vakuuttaa täten että Dual Band GSM/GPRS module tyyppinen
laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden
ehtojen mukainen.
Par la présente Telit Communications S.p.A. déclare que l'appareil Dual Band GSM/GPRS
module est conforme aux exigences essentielles et aux autres dispositions pertinentes de la
directive 1999/5/CE.
Hér með lýsir Telit Communications S.p.A. yfir því að Dual Band GSM/GPRS module er í
samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC
Con la presente Telit Communications S.p.A. dichiara che questo modulo Dual Band
GSM/GPRS è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite
dalla direttiva 1999/5/CE.
Ar šo Telit Communications S.p.A. deklarē, ka Dual Band GSM/GPRS module atbilst
Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 75 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Lithuanian
Maltese
Norwegian
Polish
Portuguese
Slovak
Slovenian
Spanish
Swedish
Šiuo Telit Communications S.p.A. deklaruoja, kad šis Dual Band GSM/GPRS module
atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Hawnhekk, Telit Communications S.p.A., jiddikjara li dan Dual Band GSM/GPRS module
jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fidDirrettiva 1999/5/EC.
Telit Communications S.p.A. erklærer herved at utstyret Dual Band GSM/GPRS module er i
samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Niniejszym Telit Communications S.p.A. oświadcza, że Dual Band GSM/GPRS module jest
zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami
Dyrektywy 1999/5/EC
Telit Communications S.p.A. declara que este Dual Band GSM/GPRS module está conforme
com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Telit Communications S.p.A. týmto vyhlasuje, že Dual Band GSM/GPRS module spĺňa
základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Telit Communications S.p.A. izjavlja, da je ta Dual Band GSM/GPRS module v skladu z
bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Por medio de la presente Telit Communications S.p.A. declara que el Dual Band
GSM/GPRS module cumple con los requisitos esenciales y cualesquiera otras disposiciones
aplicables o exigibles de la Directiva 1999/5/CE.
Härmed intygar Telit Communications S.p.A. att denna Dual Band GSM/GPRS module står
I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser
som framgår av direktiv 1999/5/EG.
In order to satisfy the essential requirements of 1999/5/EC Directive, GE866 QUAD module
is compliant with the following standards:
RF spectrum use (R&TTE art. 3.2)
EN 301 511 V9.0.2
EMC (R&TTE art. 3.1b)
EN 301 489-1 V1.9.2
EN 301 489-7 V1.3.1
Health & Safety (R&TTE art. 3.1a)
EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 +
AC:2011
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 76 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
15.1.
GE866-QUAD
The conformity assessment procedure referred to in Article 10 and detailed in Annex IV of
Directive 1999/5/EC has been followed with the involvement of the following Notified Body:
AT4 wireless, S.A.
Parque Tecnologico de Andalucía
C/ Severo Ochoa 2
29590 Campanillas – Málaga
SPAIN
Notified Body No: 1909
Thus, the following marking is included in the product:
1909
The full declaration of conformity can be found on the following address:
http://www.telit.com/
There is no restriction for the commercialisation of the GE866-QUAD module in all the
countries of the European Union.
Final product integrating this module must be assessed against essential requirements of the
1999/5/EC (R&TTE) Directive. It should be noted that assessment does not necessarily lead
to testing. Telit Communications S.p.A. recommends carrying out the following assessments:
RF spectrum use (R&TTE art. 3.2)
It will depend on the antenna used on the final product.
EMC (R&TTE art. 3.1b)
Testing
Health & Safety (R&TTE art. 3.1a)
Testing
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 77 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
Using a maximum antenna gain less or equal to than the one shown in the table below, with a
minimum distance of 20 cm between the human body and antenna, the product complies with
the European Council Recommendation 1999/519/EC on the limitation of exposure of the
general public to electromagnetic fields (0 Hz to 300 GHz).
Frequency band
Antenna gain
GSM 900
5.46 dBi
PCS 1800
11.34 dBi
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 78 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
FCC/IC Regulatory notices
Modification statement
Telit has not approved any changes or modifications to this device by the user. Any changes
or modifications could void the user’s authority to operate the equipment.
Telit n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit
la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de
l’appareil par l’utilisateur.
Interference statement
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
Wireless notice
This equipment complies with FCC and IC radiation exposure limits set forth for an
uncontrolled environment. The antenna should be installed and operated with minimum
distance of 20 cm between the radiator and your body. Antenna gain must be below:
Frequency band
Antenna gain
GSM 850
6.42 dBi
PCS 1900
1.99 dBi
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un
environnement non contrôlé. L'antenne doit être installé de façon à garder une distance
minimale de 20 centimètres entre la source de rayonnements et votre corps. Gain de l'antenne
doit être ci-dessous:
Bande de fréquence
Gain de l'antenne
GSM 850
6.42 dBi
PCS 1900
1.99 dBi
L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre antenne ou
autre émetteur.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 79 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
FCC Class B digital device notice
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Labelling Requirements for the Host device
The host device shall be properly labelled to identify the modules within the host device. The
certification label of the module shall be clearly visible at all times when installed in the host
device, otherwise the host device must be labelled to display the FCC ID and IC of the
module, preceded by the words "Contains transmitter module", or the word "Contains", or
similar wording expressing the same meaning, as follows:
Contains FCC ID: RI7GE866
Contains IC: 5131A-GE866
L'appareil hôte doit être étiqueté comme il faut pour permettre l'identification des modules qui
s'y trouvent. L'étiquette de certification du module donné doit être posée sur l'appareil hôte à
un endroit bien en vue en tout temps. En l'absence d'étiquette, l'appareil hôte doit porter une
étiquette donnant le FCC ID et le IC du module, précédé des mots « Contient un module
d'émission », du mot « Contient » ou d'une formulation similaire exprimant le même sens,
comme suit :
Contient FCC ID: RI7GE866
Contient IC: 5131A-GE866
CAN ICES-3 (B) / NMB-3 (B)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 80 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
16.
Safety Recommendations
READ CAREFULLY
Be sure the use of this product is allowed in the country and in the environment required. The
use of this product may be dangerous and has to be avoided in the following areas:
• Where it can interfere with other electronic devices in environments such as hospitals,
airports, aircrafts, etc.
• Where there is risk of explosion such as gasoline stations, oil refineries, etc. It is
responsibility of the user to enforce the country regulation and the specific
environment regulation.
Do not disassemble the product; any mark of tampering will compromise the warranty
validity. We recommend following the instructions of the hardware user guides for a correct
wiring of the product. The product has to be supplied with a stabilized voltage source and the
wiring has to be conforming to the security and fire prevention regulations. The product has to
be handled with care, avoiding any contact with the pins because electrostatic discharges may
damage the product itself. Same cautions have to be taken for the SIM, checking carefully the
instruction for its use. Do not insert or remove the SIM when the product is in power saving
mode.
The system integrator is responsible of the functioning of the final product; therefore, care has
to be taken to the external components of the module, as well as of any project or installation
issue, because the risk of disturbing the GSM network or external devices or having impact
on the security. Should there be any doubt, please refer to the technical documentation and the
regulations in force. Every module has to be equipped with a proper antenna with specific
characteristics. The antenna has
to be installed with care in order to avoid any interference with other electronic devices and
has to guarantee a minimum distance from the body (20 cm). In case of this requirement
cannot be satisfied, the system integrator has to assess the final product against the SAR
regulation.
The European Community provides some Directives for the electronic equipments
introduced on the market. All the relevant information’s are available on the European
Community website:
http://ec.europa.eu/enterprise/sectors/rtte/documents/
The text of the Directive 99/05 regarding telecommunication equipments is available,
while the applicable Directives (Low Voltage and EMC) are available at:
http://ec.europa.eu/enterprise/sectors/electrical/
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 81 of 82
Mod. 0805 2011-07 Rev.2
GE866-DUAL Hardware User Guide
1VV0301051 Rev. 2 – 2014-04-077
17.
Document History
Revision
Rev. 0
Rev. 1
Date
2013-10-02
2014-02-07
Rev.2
2014-03-03
Changes
First issue
Updated VRTC voltage, power consumption and packing
system
Added par.15
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved.
Page 82 of 82
Mod. 0805 2011-07 Rev.2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 82
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : 29f40553-c3cd-11e3-0000-f88641e0c578
Producer                        : GPL Ghostscript 8.70
Keywords                        : ()
Modify Date                     : 2014:04:11 14:05:14+02:00
Create Date                     : 2014:04:11 14:05:14+02:00
Creator Tool                    : \376\377\000P\000D\000F\000C\000r\000e\000a\000t\000o\000r\000 \000V\000e\000r\000s\000i\000o\000n\000 \0001\000.\0000\000.\0002
Document ID                     : 29f40553-c3cd-11e3-0000-f88641e0c578
Format                          : application/pdf
Title                           : \376\377\0001\000V\000V\0000\0003\0000\0001\0000\0005\0001\000_\000G\000E\0008\0006\0006\000-\000Q\000U\000A\000D\000_\000H\000a\000r\000d\000w\000a\000r\000e\000_\000U\000s\000e\000r\000_\000G\000u\000i\000d\000e\000_\000r\0002
Creator                         : \376\377\000E\000m\000i\000l\000i\000a\000I\000b
Description                     : ()
Author                          : EmiliaIb
Subject                         : 

EXIF Metadata provided by EXIF.tools