Telit Communications S p A GM862 Data Terminal Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	689305
Application ID	0TWw54rcJZK+R3LtdWq2nQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	85.42kB (1067757 bits)
Date Submitted	2006-08-02 00:00:00
Date Available	2006-08-04 00:00:00
Creation Date	2005-10-04 12:10:29
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2005-10-04 12:10:29
Document Title	Microsoft Word - 1vv0300692_GM862-QUAD Hardware User Guide_r0.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	DanieleLu

Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
T el i t
G M 8 6 2 -Q U A D
GM862-QUAD-PY
Hardware User Guide
Telit Communications S.p.A. 2005
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 1 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
Contents
OVERVIEW
HARDWARE COMMANDS
2.1
Turning ON the GM862-QUAD
2.2
Turning OFF the GM862-QUAD
2.2.1.1 Hardware shutdown
2.2.1.2 Hardware Unconditional Reset
POWER SUPPLY
3.1
Power Supply Requirements
3.2
General Design Rules
3.2.1
Electrical design Guidelines
3.2.1.1 + 5V input Source Power Supply Design Guidelines
3.2.1.2 + 12V input Source Power Supply Design Guidelines
3.2.1.3 Battery Source Power Supply Design Guidelines
3.2.1.4 Battery Charge control Circuitry Design Guidelines
3.2.2
Thermal Design Guidelines
3.2.3
Power Supply PCB layout Guidelines
10
10
11
12
12
14
15
17
SERIAL PORT
4.1
RS232 level translation
19
4.2
5V UART level translation
21
MICROPHONE
23
5.1
Microphone line Characteristic and requirements
23
5.2
General Design Rules
26
5.3
Microphone Biasing
5.3.1
Balanced Microphone biasing
5.3.2
Unbalanced Microphone biasing
26
27
28
5.4
Microphone buffering
5.4.1
Buffered Balanced Mic.
5.4.2
Buffered Unbalanced (Single Ended) Mic.
29
29
31
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 2 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
6.1
SPEAKER
Speaker lines characteristics and requirements
34
34
6.2
General Design rules
6.2.1
Noise Filtering
36
36
6.3
Handset earphone design
36
6.4
Hands Free earphone (low power) design
38
6.5
Car Kit speakerphone design
38
GENERAL PURPOSE I/O
40
7.1
Using a GPIO pin as INPUT
40
7.2
Using a GPIO pin as OUTPUT
40
7.3
Using the Alarm Output GPIO6
41
7.4
Using the Buzzer Output GPIO7
41
CAMERA
42
8.1
Agilent Camera
8.1.1
Camera interface connectors
8.1.2
EVB for camera support
42
42
44
8.2
Camera Transchip
8.2.1
Camera interface connectors
8.2.2
EVB for Agilent and Transchip camera support
8.2.3
Block Diagram for supported cameras
8.2.4
Schematic Diagrams for supported cameras
8.2.5
Example usage script for camera
45
45
47
48
49
51
52
DOCUMENT CHANGE LOG
10
ANNEX A - EVK SCHEMATICS
53
11
ANNEX B - CAMERA EVB SCHEMATICS
65
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 3 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
1 Overview
The aim of this document is the description of some hardware solutions useful for developing a
product with the Telit GM862-QUAD/-QUAD-PY modules.
In this document all the basic functions of a mobile phone will be taken into account; for each one
of them a proper hardware solution will be suggested and eventually the wrong solutions and
common errors to be avoided will be evidenced. Obviously this document can not embrace the
whole hardware solutions and products that may be designed. The wrong solutions to be avoided
shall be considered as mandatory, while the suggested hardware configurations shall not be
considered mandatory, instead the information given shall be used as a guide and a starting point for
properly developing your product with the Telit GM862-QUAD/-QUAD-PY modules. For further
hardware details that may not be explained in this document refer to the GM862-QUAD/-QUADPY Product Description document where all the hardware information is reported.
NOTE: In this document all the hardware solution are referenced to the GM862-QUAD.
As a general rule, since all the product line GM862-QUAD, GM862-QUAD-PY is pin to pin
hardware compatible, all these solutions apply also to the GM862-QUAD-PY.
NOTE
The information presented in this document is believed to be accurate and reliable. However, no responsibility is
assumed by DAI Telecom for its use, nor any infringement of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent rights of DAI Telecom other than for
circuitry embodied in Telit products. This document is subject to change without notice.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 4 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
2 Hardware Commands
2.1 Turning ON the GM862-QUAD
To turn on the GM862-QUAD the pin ON# must be tied low for at least 1 second and then released.
The maximum current that can be drained from the ON# pin is 0,1 mA.
A simple circuit to do it is:
ON#
R1
Q1
Power ON impulse
R2
GND
NOTE: don't use any pull up resistor on the ON# line, it is internally pulled up. Using pull up resistor
may bring to latch up problems on the GM862-QUAD power regulator and improper power on/off of the
module. The line ON# must be connected only in open collector configuration.
NOTE: In this document all the lines that are inverted, hence have active low signals are labeled with a
name that ends with a "#" or with a bar over the name.
TIP: To check if power has raised it is possible to monitor the START line, when this line goes high the
module is powered on, but before it remains on the device needs other 900 ms for software startup.
Hence check the PWRCTL line and 900 ms after its transition to high it is possible to release the ON#
pin.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 5 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
For example:
1- Let's assume you need to drive the ON# pin with a totem pole output of a +3/5 V microcontroller
(uP_OUT1):
2- Let's assume you need to drive the ON# pin directly with an ON/OFF button:
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 6 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
2.2 Turning OFF the GM862-QUAD
The turning off of the device can be done in three ways:
•
by software command (see GM862-QUAD Software User Guide)
•
by hardware shutdown
• by hardware unconditional shutdown
When the device is shut down by software command or by hardware shutdown, it issues to the
network a detach request that informs the network that the device will not be reachable any more.
The hardware unconditional shutdown does not issue this request and shuts down immediately the
device.
The hardware unconditional shutdown must not be used during normal operation of the device
since it does not detach the device from the network. It shall be kept as an emergency exit
procedure to be done in the rare case that the device gets stucked waiting for some network or SIM
responses.
If device does not respond to a command in the timeout window, retry issuing the command and if
still no response is received a hardware unconditional shutdown shall be issued and then a restart.
2.2.1.1 Hardware shutdown
To turn OFF the GM862-QUAD the pin ON# must be tied low for at least 1 second and then
released.
The same circuitry and timing for the power on shall be used.
The device shuts down after the release of the ON# pin.
TIP: To check if the device has powered off, the hardware line PWRCTL should be monitored. When
PWRCTL goes low, the device has powered off.
2.2.1.2 Hardware Unconditional Reset
To unconditionally turn OFF the GM862-QUAD the pin RESET# must be tied low for at least 200
milliseconds and then released.
The maximum current that can be drained from the ON# pin is 0,15 mA.
RESET#
A simple circuit to do it is:
Unconditional Power OFF
impulse
GND
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 7 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
NOTE: don't use any pull up resistor on the RESET# line nor any totem pole digital output. Using pull
up resistor may bring to latch up problems on the GM862-QUAD power regulator and improper
functioning of the module. The line RESET# must be connected only in open collector configuration.
TIP: The unconditional hardware reset should be always implemented on the boards and software
should use it as an emergency exit procedure.
For example:
1- Let's assume you need to drive the RESET# pin with a totem pole output of a +3/5 V
microcontroller (uP_OUT2):
Unconditional Reset
impulse
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 8 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
3 Power Supply
The power supply circuitry and board layout are the most important part in the full product design
and they strongly reflect on the product overall performances, hence read carefully the requirements
and the guidelines that will follow for a proper design.
3.1 Power Supply Requirements
The GM862-QUAD power requirements are:
•
Nominal Supply Voltage:
3.8 V
•
Max Supply Voltage:
4.2 V
•
Supply voltage range:
3.4 V - 4.2 V
•
Max Peak current consumption (impulsive):
1.9 A
•
Max Average current consumption during transmission (rms):
350 mA
•
Average current during Power Saving:
≈ 4 mA
•
Average current during idle (Power Saving disabled)
≈ 17 mA
The GSM system is made in a way that the RF transmission is not continuous, else it is packed into
bursts at a base frequency of about 216 Hz, the relative current peaks can be as high as about 2A.
Therefore the power supply has to be designed in order to withstand with these current peaks
without big voltage drops; this means that both the electrical design and the board layout must be
designed for this current flow.
If the layout of the PCB is not well designed a strong noise floor is generated on the ground and the
supply; this will reflect on all the audio paths producing an audible annoying noise at 216 Hz; if the
voltage drop during the peak current absorption is too much, then the device may even shutdown as
a consequence of the supply voltage drop.
TIP: The electrical design for the Power supply should be made ensuring it will be capable of a peak
current output of at least 2 A.
3.2 General Design Rules
The principal guidelines for the Power Supply Design embrace three different design steps:
- the electrical design
- the thermal design.
- the PCB layout.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 9 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
3.2.1 Electrical design Guidelines
The electrical design of the power supply depends strongly from the power source where this power
is drained. We will distinguish them into three categories:
•
+5V input (typically PC internal regulator output)
•
+12V input (typically automotive)
•
Battery
3.2.1.1 + 5V input Source Power Supply Design Guidelines
•
The desired output for the power supply is 3.8V, hence there's not a big difference between the
input source and the desired output and a linear regulator can be used. A switching power
supply will not be suited because of the low drop out requirements.
•
When using a linear regulator, a proper heat sink shall be provided in order to dissipate the
power generated.
•
A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current
absorption peaks close to the GM862-QUAD, a 100μF tantalum capacitor is usually suited.
•
Make sure the low ESR capacitor on the power supply output (usually a tantalum one) is rated
at least 10V.
•
A protection diode should be inserted close to the power input, in order to save the GM862QUAD from power polarity inversion.
An example of linear regulator with 5V input is:
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 10 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
3.2.1.2 + 12V input Source Power Supply Design Guidelines
•
The desired output for the power supply is 3.8V, hence due to the big difference between the
input source and the desired output, a linear regulator is not suited and shall not be used. A
switching power supply will be preferable because of its better efficiency especially with the 2A
peak current load represented by the GM862-QUAD.
•
When using a switching regulator, a 500Khz switching frequency regulator is preferable
because of its smaller inductor size and its faster transient response. This allows the regulator to
respond quickly to the current peaks absorption.
•
For car PB battery the input voltage can rise up to 15,8V and this should be kept in mind when
choosing components: all components in the power supply must withstand this voltage.
•
A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current
absorption peaks, a 100μF tantalum capacitor is usually suited.
•
Make sure the low ESR capacitor on the power supply output (usually a tantalum one) is rated
at least 10V.
•
For Car applications a spike protection diode should be inserted close to the power input, in
order to clean the supply from spikes.
•
A protection diode should be inserted close to the power input, in order to save the GM862QUAD from power polarity inversion. This can be the same diode as for spike protection.
An example of switching regulator with 12V input is:
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 11 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
3.2.1.3 Battery Source Power Supply Design Guidelines
•
The desired nominal output for the power supply is 3.8V and the maximum voltage allowed is
4.2V, hence a single 3.7V Li-Ion cell battery type is suited for supplying the power to the Telit
GM862-QUAD module.
The three cells Ni/Cd or Ni/MH 3,6 V Nom. battery types or 4V PB types MUST NOT BE
USED since their maximum voltage can rise over the absolute maximum voltage for the
GM862-QUAD and damage it.
NOTE: DON'T USE any Ni-Cd, Ni-MH, and Pb battery types. Their use can lead to overvoltage on the
GM862-QUAD and damage it. USE ONLY Rechargeable Li-Ion battery types.
•
A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current
absorption peaks, a 100μF tantalum capacitor is usually suited.
•
Make sure the low ESR capacitor (usually a tantalum one) is rated at least 10V.
•
A protection diode should be inserted close to the power input, in order to save the GM862QUAD from power polarity inversion. Otherwise the battery connector should be done in a way
to avoid polarity inversions when connecting the battery.
•
The battery capacity must be at least 500mAh in order to withstand the current peaks of 2A; the
suggested capacity is from 500mAh to 1000mAh.
3.2.1.4 Battery Charge control Circuitry Design Guidelines
The charging process for Li-Ion Batteries can be divided into 4 phases:
•
Qualification and trickle charging
•
Fast charge 1 - constant current
•
Final charge - constant voltage or pulsed charging
•
Maintenance charge
The qualification process consists in a battery voltage measure, indicating roughly its charge status.
If the battery is deeply discharged, that means its voltage is lower than the trickle charging
threshold, then the charge must start slowly possibly with a current limited pre-charging process
where the current is kept very low with respect to the fast charge value: the trickle charging.
During the trickle charging the voltage across the battery terminals rises; when it reaches the fast
charge threshold level the charging process goes into fast charge phase.
During the fast charge phase the process proceeds with a current limited charging; this current limit
depends on the required time for the complete charge and from the battery pack capacity. During
this phase the voltage across the battery terminals still raises but at a lower rate.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 12 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
Once the battery voltage reaches its maximum voltage then the process goes into its third state:
Final charging. The voltage measure to change the process status into final charge is very
important. It must be ensured that the maximum battery voltage is never exceeded, otherwise the
battery may be damaged and even explode. Moreover for the constant voltage final chargers, the
constant voltage phase (final charge) must not start before the battery voltage has reached its
maximum value, otherwise the battery capacity will be highly reduced.
The final charge can be of two different types: constant voltage or pulsed.
The constant voltage charge proceeds with a fixed voltage regulator (very accurately set to the
maximum battery voltage) and hence the current will decrease while the battery is becoming
charged. When the charging current falls below a certain fraction of the fast charge current value,
then the battery is considered fully charged, the final charge stops and eventually starts the
maintenance.
The pulsed charge process has no voltage regulation, instead the charge continues with pulses.
Usually the pulse charge works in the following manner: the charge is stopped for some time, let's
say few hundreds of ms, then the battery voltage will be measured and when it drops below its
maximum value a fixed time length charging pulse is issued. As the battery approaches its full
charge the off time will become longer, hence the duty-cycle of the pulses will decrease. The
battery is considered fully charged when the pulse duty-cycle is less than a threshold value,
typically 10%, the pulse charge stops and eventually the maintenance starts.
The last phase is not properly a charging phase, since the battery at this point is fully charged and
the process may stop after the final charge. The maintenance charge provides an additional charging
process to compensate for the charge leak typical of a Li-Ion battery. It is done by issuing pulses
with a fixed time length, again few hundreds of ms, and a duty-cycle around 5% or less.
This last phase is not implemented in the GM862-QUAD internal charging algorithm, so that the
battery once charged is left discharging down to a certain threshold so that it is cycled from full
charge to slight discharge even if the battery charger is always inserted. This guarantees that
anyway the remaining charge in the battery is a good percentage and that the battery is not damaged
by keeping it always fully charged (Li-Ion rechargeable battery usually deteriorate when kept fully
charged).
Last but not least, in some applications it is highly desired that the charging process restarts when
the battery is discharged and its voltage drops below a certain threshold, GM862-QUAD internal
charger does it.
As you can see, the charging process is not a trivial task to be done; moreover all these operations
should start only if battery temperature is inside a charging range, usually 5°C - 45°C.
The GM862-QUAD measures the temperature of its internal component, in order to satisfy this last
requirement, it's not exactly the same as the battery temperature but in common application the two
temperature should not differ too much and the charging temperature range should be guaranteed.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 13 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
An example of battery charger can be:
NOTE: In this particular application the battery charger input current must be limited to less than 1A.
This can be done by using a current limited wall adapter as the power source.
For your convenience in the EVK there's also a current unlimited input, where the input source is not
limited in current and the drawn current is limited to about 0,5A by a MOSFET in the EVK.
3.2.2Thermal Design Guidelines
The thermal design for the power supply heat sink should be done with the following specifications:
•
Average current consumption during transmission @PWR level max (rms): 350mA
•
Average current consumption during transmission @ PWR level min (rms): 100mA
•
Average current during Power Saving:
4mA
•
Average current during idle (Power Saving disabled)
17mA
NOTE: The average consumption during transmissions depends on the power level at which the
device is requested to transmit by the network. The average current consumption hence varies
significantly.
TIP: The thermal design for the Power supply should be made keeping a average consumption at the
max transmitting level during calls of 350mA rms.
Considering the very low current during idle, especially if Power Saving function is enabled, it is
possible to consider from the thermal point of view that the device absorbs current significantly
only during calls.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 14 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
If we assume that the device stays into transmission for short periods of time (let's say few minutes)
and then remains for a quite long time in idle (let's say one hour), then the power supply has always
the time to cool down between the calls and the heat sink could be smaller than the calculated one
for 350mA maximum RMS current, or even could be the simple chip package (no heat sink).
Moreover in the average network conditions the device is requested to transmit at a lower power
level than the maximum and hence the current consumption will be less than the 350mA, being
usually around 150mA.
For these reasons the thermal design is rarely a concern and the simple ground plane where the
power supply chip is placed can be enough to ensure a good thermal condition and avoid
overheating.
3.2.3 Power Supply PCB layout Guidelines
As seen on the electrical design guidelines the power supply shall have a low ESR capacitor on the
output to cut the current peaks and a protection diode on the input to protect the supply from spikes
and polarity inversion. The placement of these components is crucial for the correct working of the
circuitry. A misplaced component can be useless or can even decrease the power supply
performances.
•
The Bypass low ESR capacitor must be placed close to the Telit GM862-QUAD power input
pins or in the case the power supply is a switching type it can be placed close to the inductor to
cut the ripple provided the PCB trace from the capacitor to the GM862-QUAD is wide enough
to ensure a dropless connection even during the 2A current peaks.
•
The protection diode must be placed close to the input connector where the power source is
drained.
•
The PCB traces from the input connector to the power regulator IC must be wide enough to
ensure no voltage drops occur when the 2A current peaks are absorbed. Note that this is not
made in order to save power loss but especially to avoid the voltage drops on the power line at
the current peaks frequency of 216 Hz that will reflect on all the components connected to that
supply, introducing the noise floor at the burst base frequency. For this reason while a voltage
drop of 300-400 mV may be acceptable from the power loss point of view, the same voltage
drop may not be acceptable from the noise point of view. If your application doesn't have audio
interface but only uses the data feature of the Telit GM862-QUAD, then this noise is not so
disturbing and power supply layout design can be more forgiving.
•
The PCB traces to the GM862-QUAD and the Bypass capacitor must be wide enough to ensure
no voltage drops occur when the 2A current peaks are absorbed. This is for the same reason as
previous point. Try to keep this trace as short as possible.
•
The PCB traces connecting the Switching output to the inductor and the switching diode must
be kept as short as possible by placing the inductor and the diode very close to the power
switching IC (only for switching power supply). This is done in order to reduce the radiated
field (noise) at the switching frequency (100-500 kHz usually).
•
The use of a good common ground plane is suggested.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 15 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
•
The placement of the power supply on the board should be done in such a way to guarantee that
the high current return paths in the ground plane are not overlapped to any noise sensitive
circuitry as the microphone amplifier/buffer or earphone amplifier.
•
The power supply input cables should be kept separate from noise sensitive lines such as
microphone/earphone cables.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 16 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
4 Serial Port
The serial port on the Telit GM862-QUAD is the core of the interface between the module and
OEM hardware. Several configurations can be designed for the serial port on the OEM hardware,
but the most common are:
- RS232 PC com port
- microcontroller UART @ 2.8V - 3V (Universal Asynchronous Receive Transmit)
- microcontroller UART@ 5V or other voltages different from 2.8V
Depending from the type of serial port on the OEM hardware a level translator circuit may be
needed to make the system work. The only configuration that doesn't need a level translation is the
2.8V UART.
The serial port on the GM862-QUAD is a +2.8V UART with all the 7 RS232 signals. It differs
from the PC-RS232 in the signal polarity (RS232 is reversed) and levels. The levels for the GM862QUAD UART are the CMOS levels:
Absolute Maximum Ratings -Not Functional
Parameter
Min
Max
Input level on any
digital pin when on
-0.3V
+3.75V
Input voltage on
-0.3V
analog pins when on
+3.0 V
Operating Range - Interface levels (2.8V CMOS)
Level
Min
Max
Input high level VIH 2.1V
3.3V
Input low level
0.5V
VIL 0V
Output high level VOH 2.2V
3.0V
Output low level VOL 0V
0.35V
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 17 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
The signals of the GM862-QUAD serial port are:
RS232
Pin
Number
Signal
GM862QUAD
Pin
Number
Name
Usage
DCD dcd_uart
36
Data Carrier Detect
Output from the GM862-QUAD that
indicates the carrier presence
RXD tx_uart
37
Transmit line *see Note
Output transmit line of GM862-QUAD
UART
TXD rx_uart
20
Receive line *see Note
Input receive of the GM862-QUAD
UART
DTR dtr_uart
43
Data Terminal Ready
Input to the GM862-QUAD that controls
the DTE READY condition
GND
2-4-6-8
Ground
ground
DSR dsr_uart
33
Data Set Ready
Output from the GM862-QUAD that
indicates the module is ready
RTS rts_uart
45
Request to Send
Input to the GM862-QUAD that controls
the Hardware flow control
CTS cts_uart
29
Clear to Send
Output from the GM862-QUAD that
controls the Hardware flow control
RI ri_uart
30
Ring Indicator
Output from the GM862-QUAD that
indicates the incoming call condition
NOTE: According to V.24, RX/TX signal names are referred to the application side, therefore on the
GM862-QUAD side these signal are on the opposite direction: TXD on the application side will be
connected to the receive line (here named TXD/ rx_uart ) of the GM862-QUAD serial port and viceversa
for RX.
TIP: For a minimum implementation, only the TXD and RXD lines can be connected, the other lines can
be left open provided a software flow control is implemented.
The signals in the UART connector on the EVK are:
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
GND
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 18 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
4.1 RS232 level translation
In order to interface the Telit GM862-QUAD with a PC com port or a RS232 (EIA/TIA-232)
application a level translator is required. This level translator must
- invert the electrical signal in both directions
- change the level from 0/3V to +15/-15V
Actually, the RS232 UART 16450, 16550, 16650 & 16750 chipsets accept signals with lower levels
on the RS232 side (EIA/TIA-562) , allowing for a lower voltage-multiplying ratio on the level
translator. Note that the negative signal voltage must be less than 0V and hence some sort of level
translation is always required.
The simplest way to translate the levels and invert the signal is by using a single chip level
translator. There are a multitude of them, differing in the number of driver and receiver and in the
levels (be sure to get a true RS232 level translator not a RS485 or other standards).
By convention the driver is the level translator from the 0-3V UART level to the RS232 level, while
the receiver is the translator from RS232 level to 0-3V UART.
In order to translate the whole set of control lines of the UART you will need:
- 5 driver
- 3 receiver
NOTE: The digital input lines working at 2.8VCMOS have an absolute maximum input voltage of 3,75V;
therefore the level translator IC shall not be powered by the +3.8V supply of the module. Instead it
shall be powered from a +2.8V / +3.0V (dedicated) power supply.
This is because in this way the level translator IC outputs on the module side (i.e. GM862-QUAD
inputs) will work at +3.8V interface levels, stressing the module inputs at its maximum input voltage.
This can be acceptable for evaluation purposes, but not on production devices.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 19 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
An example of level translation circuitry of this kind is:
the RS232 serial port lines are usually connected to a DB9 connector with the following layout:
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 20 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
4.2 5V UART level translation
If the OEM application uses a microcontroller with a serial port (UART) that works at a voltage
different from 2.8 - 3V, then a circuitry has to be provided to adapt the different levels of the two
set of signals. As for the RS232 translation there are a multitude of single chip translators, but since
the translation requires very few components, then also a discrete design can be suited. For example
a possible inexpensive translator circuit for a 5V driver can be:
and for a 5V receiver:
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 21 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
NOTE: The UART input line TXD (rx_uart) of the GM862-QUAD is NOT internally pulled up with a
resistor, so there may be the need to place an external 47KΩ pull-up resistor, either the DTR (dtr_uart)
and RTS (rts_uart) input lines are not pulled up internally, so an external pull-up resistor of 47KΩ may
be required.
A power source of the internal interface voltage corresponding to the 2.8VCMOS high level is
available at the PWRCTL pin on the connector, whose absolute maximum output current is 10mA.
A maximum of 9 47 KΩ pull-up resistors can be connected to the PWRCTL pin, provided no other
devices are connected to it and the pulled-up lines are GM862-QUAD input lines connected to
open collector outputs in order to avoid latch-up problems on the GM862-QUAD.
Care must be taken to avoid latch-up on the GM862-QUAD and the use of this output line to power
electronic devices shall be avoided, especially for devices that generate spikes and noise such as
level translators, digital ICs or microcontrollers, failure in any of these condition can severely
compromise the GM862-QUAD functionality.
NOTE: The input lines working at 2.8VCMOS can be pulled-up with 47KΩ resistors that can be
connected directly to the PWRCTL line provided they are connected as in this example.
NO OTHER devices should be powered with the PWRCTL line, otherwise the module functionality may
be compromised.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 22 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
5 Microphone
The microphone circuitry is the more noise sensitive and its design and layout must be done with
particular care.
5.1 Microphone line Characteristic and
requirements
The Telit GM862-QUAD provides two audio paths for the microphone and the earpiece: the
internal and the external audio paths. Only one of the two paths can be active at a time and it is
selectable by hardware line AXE or by AT command. The audio characteristics of the two paths are
slightly different and this should be kept in mind when designing. The internal audio path should be
used for handset function, while the external audio path is suited for hands free function (car kit).
Both microphone paths from the Telit GM862-QUAD are balanced and the OEM circuitry should
be designed balanced to reduce the common mode noise typically generated on the ground plane,
however for particular OEM application needs also an unbalanced circuitry can be used.
The microphone input lines characteristics are:
internal microphone path
•
line coupling:
AC ( 100nF cond.)
•
line type:
balanced
•
differential input resistance:
25kΩ
•
line nominal sensitivity:
50 mVrms
•
max input voltage:
360 mVrms
•
microphone nominal sensitivity/analog gain suggested:
-45 dBVrms/Pa / +24dB
•
echo canceller type:
handset
external microphone path
•
line coupling:
AC ( 100nF cond.)
•
line type:
balanced
•
differential input resistance:
25kΩ
•
line nominal sensitivity:
3 mVrms
•
max input voltage:
22 mVrms
•
microphone nominal sensitivity/analog gain suggested:
-45 dBVrms/Pa / +10dB
•
echo canceller type:
car kit hands free
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 23 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
TIP: Due to the difference in the echo canceller type, the internal audio path is suited for handset
applications while the external audio path is suited for car kit hands free. The headset applications
should be made by using the external audio path but DISABLING the echo canceller by software AT
command. If the echo canceller is left active with the headset, then some echo might be introduced by
the echo cancel algorithm.
The nominal sensitivity of the line indicates the voltage level on the GM862-QUAD pins that
should be present during "normal spoken" conditions: for a handset a voice signal coming from the
mouth of the talker at 7 cm of distance from the microphone, producing an acoustic pressure of -4,7
dBPa (@ 1 kHz) on the microphone membrane.
For example:
With the internal mic. having the suggested nominal sensitivity -45dBVrms/Pa
at the "normal spoken" conditions: -4.7dB Pa on the microphone membrane.
At that acoustic pressure the voltage output from the microphone is:
Voltage Output (dB) = ( -45) + (-4.7) = -49.7 dBVrms
corresponding to:
Voltage Output = 10 ( -49.7 / 20 ) = 3.3* 10 -3 Vrms
by having the microphone gain set to +24 dB (corresponding to 15.8 times) the signal in the
nominal conditions on the input mic. pins of the GM862-QUAD will be:
Voltage @ GM862-QUAD_mic = 3.3 * 10 -3 * 15.8 = 51 mVrms
During the spoken conditions the signal varies according to the volume of the voice of the talker,
usually a rough thumb rule for the dynamic range may be considered:
* +20dB (10 times) at maximum voice level (talker screaming)
* -50 dB (1/300 times) at minimum voice level (talker whispering).
For the handsfree/car kit microphone the voice attenuation due to the distance between the
microphone and the talker must be taken into account when designing the microphone amplifier.
For a car cabin usually the distance between the talker and the mic. is about 50cm; in these
conditions the attenuation can be considered as a thumb rule around 20dB.
Another thing to consider, especially for cabin car use, is the fact that the external mic. will pick up
also ambient noise; to overcome this problem it is preferable to set the gain of the microphone 10dB
lower with respect to the calculated value for a nominal sensitivity. The corresponding reduction in
signal level will be compensated by an increased voice volume of the talker which will speak louder
because of the ambient noise.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 24 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
For the headset we shall distinguish two different types: the headsets having the microphone
sustained close to the mouth and the headsets having the microphone on the earpiece cable.
The same considerations for the additional voice attenuation due to the distance from the
microphone and the noise pick up can be made for the headset having the microphone on the
earpiece cable, while the other kind of headset shall be threaten as an handset.
For example:
With the external mic. having the suggested nominal sensitivity -45dBVrms/Pa
at the "normal spoken" conditions: -4.7dB Pa at 7 cm from the mouth of the talker and with a
further attenuation of 20dB due to the distance from the microphone (about 50 cm).
At that acoustic pressure the voltage output from the microphone is:
Voltage Output (dB) = ( -45) + (-4.7) - 20 = -69.7 dBVrms
corresponding to:
Voltage Output = 10 ( -69.7 / 20 ) = 3.3* 10 -4 Vrms
by having the microphone gain set to +10 dB (corresponding to 3 times) the signal in the nominal
conditions on the input external mic. pins of the GM862-QUAD will be:
Voltage @ GM862-QUAD__extmic = 3.3 * 10 -4 * 3 = 1 mVrms
Hence in these conditions the signal level on the input pins of the external mic. of the GM862QUAD is 10 dB (3 times) lower than the nominal, as suggested.
The microphones usually need a biasing network that provides the necessary DC current to the mic.,
this will be explained further on.
In the EVK all the microphone input jacks have the hot wire connected to the central pole.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 25 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
5.2 General Design Rules
There are several configurations for the audio path, but the most effective difference is between
balanced and unbalanced microphone.
It is highly recommended to keep the whole microphone path balanced even if this means having 2
wires connecting the microphone instead of one needed (plus ground) in the unbalanced case. The
balanced circuitry is more suited because of its good common mode noise rejection, reducing the
216 Hz burst noise produced during the GSM transmissions.
•
Where possible use balanced microphone circuitry
•
Keep the microphone traces on the PCB and wires as short as possible.
•
If your application requires an unbalanced microphone, then keep the lines on the PCB
balanced and "unbalance" the path close to the microphone wire connector if possible.
•
For the microphone biasing voltage use a dedicated voltage regulator and a capacitor multiply
circuit.
•
Make sure that the microphone traces in the PCB don't cross or run parallel to noisy traces
(especially the power line)
•
If possible put all around to the microphone lines a ground trace connected to the ground plane
by several vias. This is done in order to simulate a shielded trace on the PCB.
•
The biasing circuit and eventually the buffer can be designed in the same manner for the
internal and external microphones.
5.3 Microphone Biasing
The electret microphones usually need a biasing voltage to work properly. Refer to your
microphone provider for the characteristics required.
NOTE: The microphones have a hot wire were the positive biasing must be connected, usually it is
indicated by a + sign or a red point. If the polarity of the bias is reversed, then the microphone will not
work properly. For this reason be sure to respect the mic. biasing polarity.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 26 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
5.3.1 Balanced Microphone biasing
The balanced microphone bias voltage should be obtained from a dedicated voltage regulator, in
order to eliminate the noise present on the power lines. This regulator can be the same for all the
audio paths. The microphone should be supplied from a capacitor multiply circuit.
For example a circuit for the balanced microphone biasing can be:
NOTE: In the balanced application the resistors R2 and R3 must have the same value to keep the
circuit balanced.
NOTE: The cable to the microphone should not be shielded, instead a twisted pair cable shall be used.
NOTE: The microphone sensitivity changes with the value of R2 and R3. Usually the microphones are
characterized with 2kΩ biasing resistance, so try to keep the sum of R2 and R3 around 2kΩ. Refer to
your microphone manufacturer for the mic. characteristics.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 27 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
5.3.2 Unbalanced Microphone biasing
The unbalanced microphone biasing voltage should be obtained from a dedicated voltage regulator,
in order to eliminate the noise present on the power lines. This regulator can be the same for all the
audio paths. The microphone should be supplied from a capacitor multiply circuit.
For example a circuit for the unbalanced microphone biasing can be:
NOTE: In the unbalanced application the capacitor C3 shall be > 200nF otherwise the frequency
response will be cut at low band frequencies (down to 300Hz). This capacitor can be placed close to
the MIC- pin (EXT_MIC- or INT_MIC- depending on the audio path chosen) or if possible it should be
placed close to the shielded cable connector. If the ground return path is well designed, then it is
possible to eliminate the C3 capacitor, provided the buffer is close to the mic. input.
NOTE: The cable to the microphone should be shielded.
NOTE: The microphone sensitivity changes with the value of R2. Usually the microphones are
characterized with 2kΩ biasing resistance, so try to keep the value of R2 around 2kΩ. For mic.
characteristics refer to the manufacturer.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 28 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
5.4 Microphone buffering
As seen previously, a microphone shall be connected to the input pins of the GM862-QUAD
through a buffer amplifier that boosts the signal level to the required value.
Again the buffered microphone circuitry can be balanced or unbalanced. Where possible it is
always preferable a balanced mic. solution. The buffering circuit shall be placed close to the
microphone or close to the microphone wire connector.
5.4.1 Buffered Balanced Mic.
A sample circuit can be:
This circuit has a gain of 15 times (+24 dB), and is therefore suited for the internal mic. input,
having a microphone with a sensitivity close to the suggested one (-45 dBVrms/Pa), if the used
microphone has a different sensitivity, or if the buffer is connected to the external mic. input, then a
gain adjustment shall be done by changing resistors R604-R605 and R606-R607 and as a
consequence the capacitors C636 and C637 to maintain the bandwidth 150-8000 (-3dB).
The buffer gain is given by the formula:
Gain =
R604 R606
R605 R607
The C636 and C637 capacitors are placed in order to cut off the gain at higher frequencies than the
transmitted GSM band, the cutoff frequency (-3dB) should be 8 kHz in order to have -1dB at 4Khz.
The cutoff frequency is given by the formula:
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 29 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
freq. =
[Hz]
2π * R 604 * C 637 2π * R606 * C 636
For example:
- Let's assume you have a microphone with these characteristics:
- sensitivity -45 dBVrms/Pa
and you want to use it in the internal mic. audio path.
With the mic. having nominal sensitivity -45dBVrms/Pa at the "normal spoken" conditions: -4.7dB Pa
at 7 cm from the mouth of the talker.
At that acoustic pressure the voltage output from the microphone is:
Mic Voltage Output (dB) = ( -45) + (-4.7) = -49.7 dBVrms
corresponding to:
Mic_Voltage_Output = 10 ( -49.7 / 20 ) = 3.3* 10 -3 Vrms
in order to have a signal of 50 mVrms on the GM862-QUAD internal mic. inputs then the buffer must
have a gain of:
Voltage @ GM862-QUAD_intmic/ Mic_Voltage_Output = (50 * 10 -3 )/( 3.3 * 10 -3 ) = 15
Hence in these conditions the signal level on the input pins of the internal mic. of the GM862QUAD is 24 dB (15 times) higher than the microphone output and therefore the buffer has to gain
24 dB.
The corresponding values for the resistors on the buffer could be ( if we keep the input resistance
10kΩ )
R604 = R606 = gain* R603= gain* R605 = 15* 10 = 150 kΩ
The commercial values of 150kΩ & 10kΩ are then chosen.
As a consequence the values of the capacitors C636 and C637 shall be:
C636=C637= 1/ (2π*8000*R606)= 132 *10 -12 F
A commercial value of 100pF is then chosen.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 30 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
5.4.2 Buffered Unbalanced (Single Ended) Mic.
A sample schematic for a buffered unbalanced (single ended) microphone can be:
The schematic does not include the required mic. biasing circuitry. For the biasing the same circuit
as seen before can be used; to be noticed that the capacitor C3 on the unbalanced biasing circuit is
not anymore needed if this Buffered design is used.
Two different configurations are used, one inverting and the other not inverting, hence an additional
+6dB (2 times) gain is achieved by doubling the mic. signal path.
The gain of the not inverting buffer is given by the formula:
R719
R720
and hence it cannot be less than 1. In the example shown the gain of the not inverting buffer is 1,5
(4dB).
While the gain of the inverting buffer is given by the formula:
Gain = 1 +
R 711
R708
As shown in the balanced buffered mic. the gain adjustments can be done by changing R719 - R720
and R708 - R711 and as a consequence the capacitors C726 and C727.
Gain =
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 31 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
The bandwidth (-3dB) is given by the approximated formula (considering C725 >> C726) :
[Hz]
2π * R719 * C 726 2π * R711* C 727
The buffer bandwidth at -3dB shall be 8kHz.
Note that the biasing of the operational amplifier is given for the inverting amplifier by the series
divider R714-R715. The 100nF capacitor C719 is needed to filter the noise that could be coupled to
that divider. For the not inverting operational the biasing is given by a different divider R715-R717
with the capacitor C720 and through a series resistor R718 of 470KΩ.
freq. =
For example:
- Let's assume you have a microphone with these characteristics:
- sensitivity -45 dBVrms/Pa
and you want to use it in the external mic. audio path.
With the mic. having nominal sensitivity -45dBVrms/Pa at the "normal spoken" conditions: -4.7dB Pa
but at 50 cm from the mouth of the talker an additional 20 dB loss shall be considered.
At that acoustic pressure the voltage output from the microphone is:
Mic Voltage Output (dB) = ( -45) + (-4.7) -20 = -69.7 dBVrms
corresponding to:
Mic_Voltage_Output = 10 ( -69.7 / 20 ) = 3.3* 10 -4 Vrms
in order to have a signal of 1 mVrms (10 dB lower than the nominal input for the GM862-QUAD
external mic. path) on the GM862-QUAD internal mic. inputs then the buffer must have a gain of:
Voltage @ GM862-QUAD_intmic/ Mic_Voltage_Output = (1 * 10 -3 )/( 3.3 * 10 -4 ) = 3
Hence in these conditions the signal level on the input pins of the internal mic. of the GM862QUAD is 10 dB (3 times) higher than the microphone output and therefore the buffer has to gain 10
dB.
To calculate the resistor values it must be kept in mind that balancing the line will double the signal
and hence already add +6 dB, therefore the buffer must gain only 1.5 times.
The corresponding values for the resistors on the buffer could be ( if we keep the input resistance
10kΩ )
R711 = gain* R708= 1.5* 10 = 15 kΩ
R719 = (gain -1) * R720 = (1.5 -1) * 10 = 5 kΩ
The commercial values of 15kΩ & 5.6kΩ are then chosen.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 32 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
As a consequence the values of the capacitors C726 and C727 shall be:
C726= 1/ (2π*8000*R719)= 3.5 *10 -9 F
C727= 1/ (2π*8000*R711)= 1,2 *10 -9 F
The commercial values of 3.3nF and 1nF are then chosen.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 33 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
6 Speaker
6.1 Speaker lines characteristics and requirements
The Telit GM862-QUAD provides two audio paths for both the microphone and the earpiece: the
internal and the external audio paths. Only one of the two paths can be active at a time and it is
selectable by hardware line AXE or by AT command. The audio characteristics of the two paths are
slightly different and this should be kept in mind when designing your application. The internal
audio path should be used for handset function, while the external audio path is suited for hands free
function (car kit).
Both speaker outputs from the Telit GM862-QUAD are bridged type and the OEM circuitry shall
be designed bridged to reduce the common mode noise typically generated on the ground plane and
to get the maximum power output from the device; however for particular OEM application needs
also a single ended circuitry can be designed.
The GM862-QUAD speaker output lines characteristics are:
internal speaker path ( EAR_MT+ , EAR_MT- )
•
line coupling:
DC
•
line type:
bridged
•
speaker impedance (operating conditions):
≥ 16 Ω ± 5% @ 1kHz
•
minimum load impedance:
15 Ω
•
signal bandwidth:
150 - 8000 Hz @ -3 dB
•
maximum differential output:
850 mVrms
•
rated output power:
10 mW
•
maximum power output:
30 mW
•
volume level steps (SW):
- 2 dB
•
number of volume steps(SW):
10
external speaker path ( EAR_HF+ , EAR_HF- )
•
line coupling:
DC
•
line type:
bridged
•
speaker impedance (operating conditions):
≥ 16 Ω ± 15% @ 1kHz
•
minimum load impedance:
15 Ω
•
signal bandwidth:
150 - 8000 Hz @ -3 dB
•
maximum differential output:
425 mVrms
•
rated output power:
2.5 mW
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 34 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
•
maximum power output:
7.5 mW
•
volume level steps (SW):
- 2 dB
•
number of volume steps (SW):
10
The EVK v.1.2 audio output characteristics are:
internal/external ear single ended
•
line coupling:
AC
•
line type:
single ended referred to GND
•
speaker impedance (operating conditions):
≥8Ω
•
minimum load impedance:
8Ω
•
signal bandwidth:
150 - 8000 Hz @ -3 dB
•
maximum output:
800 mVrms
•
maximum power output:
80 mW @ 8 Ω
•
THD+N
1% @ 80mW
internal/external ear bridged
•
line coupling:
DC
•
line type:
bridged not referred to GND
•
speaker impedance (operating conditions):
≥8Ω
•
minimum load impedance:
8Ω
•
signal bandwidth:
150 - 8000 Hz @ -3 dB
•
maximum output:
1.6 Vrms
•
maximum power output:
320 mW @ 8 Ω
•
THD+N
1% @ 330mW
high power external ear
•
line coupling:
DC
•
line type:
bridged not referred to GND
•
speaker impedance (operating conditions):
≥4Ω
•
minimum load impedance:
4Ω
•
signal bandwidth:
150 - 8000 Hz @ -3 dB
•
maximum power output:
6W
•
THD+N
10% @ 6 W
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 35 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
6.2 General Design rules
There are several configurations for the audio output path, but the various design requirements can
be grouped into three different categories:
•
handset earphone (low power, typically a handset)
•
hands free earphone (low power, typically a headset)
•
car kit speakerphone (high power, typically a speaker)
The three groups have different power requirements, usually the first two applications need only
few mW of power, which can be directly drained from the GM862-QUAD pins, provided a suited
speaker is used. This direct connect design is the cheaper and simpler solution and will be suited for
the most of the earphone design requirements. There's no need to decouple the output ear lines if a
suited earpiece is connected. For the last group, the speakerphone, a power amplifier is required to
raise the output power up to 5-10W required in a car cabin application.
All the designs shall comply with the following guidelines:
•
Where possible use a bridged earphone circuitry, to achieve the maximum power output from
the device.
•
Keep the earphone traces on the PCB and wires as short as possible.
•
If your application requires a single ended earpiece and you want a direct connection, then
leave one of the two output lines open and use only the other referred to ground. Remember
that in this case the power output is 4 times lower than the bridged circuit and may not be
enough to ensure a good voice volume.
•
Make sure that the earphone traces in the PCB don't cross or run parallel to noisy traces
(especially the power line)
•
The cable to the speaker shall be a twisted pair with both the lines floating for the bridged
output type, shielded with the shield to ground for the single ended output type.
6.2.1 Noise Filtering
The I/O of the PCB should have a noise filter close to the connector, to filter the high frequency
GSM noise. The filter can be a Π of 2 capacitor and a inductance, with the one capacitor of 39pF 0603 case , and the other capacitor of 1nF - 0603; the inductance shall have a value of 39μH .
6.3 Handset earphone design
As seen previously, a 16Ω speaker can be directly connected to the output pins EAR_MT+ and
EAR_MT- of the GM862-QUAD.
This solution is often the more cost effective, reducing the components count to a minimum. There
are several limitations to the use of this solution: speaker direct connect imposes the speaker
characteristics to be almost exactly the suggested ones, otherwise the power output may be reduced
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 36 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
(if speaker impedance is bigger than 16Ω) or the GM862-QUAD ear port may be damaged (if
speaker impedance is less than 15Ω).
The other limitation of the speaker direct connection is the power output capability of the GM862QUAD which is limited and for some particular applications may not be enough.
For these reasons, when the power output of the GM862-QUAD is not enough or if the speaker
characteristics are different from the suggested, then it is preferable to use an amplifier to increase
the power and current output capabilities.
Again the output from the GM862-QUAD is bridged and both lines should be used, where possible,
as inputs to the power amplifier. This ensures a higher common mode rejection ratio, reducing the
GSM current busts noise on the speaker output.
In this case the EAR_MT lines from the GM862-QUAD should be AC coupled with a capacitor of
100nF.
It is always desirable to have a mute control on the amplifier, in order to turn it off while the device
is not sending signal to the output, in this manner the amplifier background noise which may be
audible during idle conditions is cut off.
A principle schematic may be:
The resulting gain and high pass cut can be obtained with the formula:
Gain =
freq. =
R3
R2
[Hz]
2π * R3 * C 4
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 37 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
And an example of internal Ear amplifier is:
Some amplifier require a low impedance load at high frequency in order to avoid auto oscillation,
this can be made with a capacitor (100nF) in series with a resistor (15Ω).
When designing your application, remember to provide an adequate bypass capacitor to the
amplifier and place it close to the power input pin of the IC, keeping the traces as short as possible.
6.4 Hands Free earphone (low power) design
The same design considerations made for the handset are valid for the hands free earphone, the only
difference is that the external ear audio output level from the GM862-QUAD is 6dB lower than the
internal one, so the gain of the amplifier must be 6dB higher to provide the same audio level.
6.5 Car Kit speakerphone design
For the car kit speaker phone function the power output requirement is usually at least 4W,
therefore an amplifier is needed to boost the GM862-QUAD output.
The design of the amplifier shall comply with the following guidelines:
•
The input to the amplifier MUST be taken from the external audio path (EAR_HF+, EAR_HF-)
of the GM862-QUAD, because of its echo canceller parameters suited to a car cabin use.
•
The amplifier shall have a gain of 30-40 times ( 29-32 dB) to provide the desired output power
of 5-10W with the signal from the GM862-QUAD external audio output lines (EAR_HF).
•
If the amplifier has a fixed gain then it can be adjusted to the desired value by reducing the input
signal with a resistor divider network.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 38 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
•
The amplifier shall have a mute control to be used while not in conversation. This results in two
benefits: eliminating the background noise when not in conversation and saving power.
•
The power to the amplifier should be decoupled as much as possible from the GM862-QUAD
power supply, by either keeping separate wires and placing bypass capacitors of adequate value
close to the amplifier power input pins.
•
The biasing voltage of the amplifier shall be stabilised with a low ESR (e.g. a tantalum)
capacitor of adequate value.
NOTE: The GM862-QUAD audio path connected to the car kit hands free amplifier MUST be the
external one (EAR_HF), otherwise the echo cancellation will not be done due to the difference in the
echo canceller characteristics of the GM862-QUAD internal audio path from the external audio path.
An example of car kit amplifier schematic can be:
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 39 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
7 General Purpose I/O
The general purpose I/O pins can be configured to act in three different ways:
- input
- output
- alternate function (internally controlled)
Input pins can only be read and report the digital value (high or low) present on the pin at the read
time; output pins can only be written or queried and set the value of the pin output; an alternate
function pin is internally controlled by the GM862-QUAD firmware and acts depending on the
function implemented.
Not all GPIO pins support all these three modes:
- GPIO1 is an INPUT ONLY
- GPIO2 is an OUTPUT ONLY (open collector)
- GPIO3, GPIO4 and GPIO5 support both input or output mode but not Alternate function.
- GPIO6 supports all three modes and can be input, output, alarm output (Alternate function)
- GPIO7 supports all three modes and can be input, output, buzzer output (Alternate function)
All GPIO pins except from GPIO1 and GPIO2 that are buffered with a transistor, are 2.8V CMOS
signals and their interface levels are the same specified in the paragraph 4 Serial Port.
7.1 Using a GPIO pin as INPUT
The GPIO pins, when used as inputs, can be connected to a digital output of another device and
report its status, provided this device has interface levels compatible with the 2.8V CMOS levels of
the GPIO.
If the digital output of the device to be connected with the GPIO input pin has interface levels
different from the 2.8V CMOS, then it can be connected to GPIO1 or can be buffered with an open
collector transistor, provided a 47KΩ pull-up resistor is connected as seen in the paragraph 4.2 5V
UART level translation.
7.2 Using a GPIO pin as OUTPUT
The GPIO pins, when used as outputs, can drive 2.8V CMOS digital devices or compatible
hardware. When set as outputs, the pins (except from GPIO2 which is Open Collector) have a pushpull output and therefore the pull-up resistor may be omitted.
The GPIO2 pin, since it is an Open Collector output needs an external pull-up resistor.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 40 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
7.3 Using the Alarm Output GPIO6
The GPIO6 pin, when configured as Alarm Output, is controlled by the GM862-QUAD module and
will rise when the alarm starts and fall after the issue of a dedicated AT command.
This output can be used to power up the GM862-QUAD controlling microcontroller or application
at the alarm time, giving you the possibility to program a timely system wake-up to achieve some
periodic actions and completely turn off either the application and the GM862-QUAD during sleep
periods, drammatically reducing the sleep comsumption to few μA.
In battery powered devices this feature will greatly improve the autonomy of the device.
7.4 Using the Buzzer Output GPIO7
The GPIO7 pin, when configured as Buzzer Output, is controlled by the GM862-QUAD module
and will drive with appropriate square waves a Buzzer driver.
This permits to your application to easily implement Buzzer feature with ringing tones or melody
played at the call incoming, tone playing on SMS incoming or simply playing a tone or melody
when needed by your application.
A sample interface scheme is included below to give you an idea of how to interface a Buzzer to the
GPIO7:
NOTE: To correctly drive a buzzer a driver must be provided, its characteristics depend on the Buzzer
and for them refer to your buzzer vendor.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 41 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
8 Camera
8.1 Agilent Camera
The GM862-QUAD provides a direct support for digital cameras with the following characteristics:
Type:
AGILENT ADCM2650
Technology:
CMOS COLOR camera
Max picture size:
VGA 640x480 pixels
Output format:
JPEG
Sensitivity:
5 lux
8.1.1 Camera interface connectors
The interface connection between GM862-QUAD and camera is provided by the 50-pins Molex
connector of the module and a 18-pins ZIF connector vertical type for the CMOS camera.
Molex 52991-0508 GM862
ZIF CF21181V0RP
Pin Signal
I/O Function
Pin Signal
I/O
21
CAM_SYNC
End of frame is an output for the
camera and an input for the GM862QUAD.
16
EOF
25
MON1_CAM
The module clock is provided by the
MON1_CAM output of the GM862QUAD.
17
MCLK
28
IICSCL_CAM
IICbus serial clock
S_CLK
32
PD(0)
I/O Parallel Data 0
15
DATA0
I/O
34
PD(1)
I/O Parallel Data 1
14
DATA1
I/O
38
PD(2)
I/O Parallel Data 2
13
DATA2
I/O
40
PD(3)
I/O Parallel Data 3
12
DATA3
I/O
42
PD(4)
I/O Parallel Data 4
11
DATA4
I/O
44
PD(5)
I/O Parallel Data 5
10
DATA5
I/O
46
PD(6)
I/O Parallel Data 6
DATA6
I/O
49
PD(7)
I/O Parallel Data 7
DATA7
I/O
47
IICSDA_CAM
I/O IICbus serial data
S_DATA
I/O
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 42 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
48
CAM_DRDY
50
CAM_PWR_ON O
2-4- GND
Data ready in an output for the camera
and an input for the GM862-QUAD
DR
2,8V power supply enable for the
camera
VCC_MAIN I
Horizontal sync n.c.
HSYNC
Input command for switching power
ON or OFF
ON_OFF
Ground
118
GND
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 43 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
NOTE: GM862-QUAD is 100% pin-to-pin compatible with previous GM862 models. Therefore, in order
to connect the camera to the standard 50-pins Molex industrial connector, some pins will have dualfunction (GPIO pins, except for GPIO1): as usual GPIO operations or CAMERA support. See Molex PINOUT described in the GM862-QUAD Product description.
NOTE: The CMOS camera must be removed when the GPIO pins are used for I/O purpose.
NOTE: The white point on the ADCM2650 camera cable have to match with pin18 on ZIF connector.
8.1.2 EVB for camera support
In order to interface the Telit GM862-QUAD with a CMOS camera, Telit has developed an
evaluation board. The EVB is provided by:
•
10 pin Berg male connector (PL201) and RS232 level translator that allows a direct connection
to the PC. To switch on the level translator a jumper shall be set on PL203.
•
12 pin Berg male connector (PL202) to supply the GM862-QUAD mounted on the EVB. The
input source power should be in the range 4,5V-12V. Charge line is also provided in case a LiIon battery is connected to the VBATT pins. Charge input must fulfil charger line requests.
•
50 pin Molex male connector (PL103) to interface with the GM862-QUAD directly.
•
30 pin Berg male connector (PL101) to interface with a PCB developed by the user or the EVK
board. On this connector is available the complete audio path, the serial port lines with full
handshaking, and the pins ON, AXE, RESET, GPIO1 and STAT_LED. Also the
CHARGER_IN pin can be available placing a 0 ohm resistor.
•
18 pin ZIF female connector (SO101) for CMOS camera.
•
ON/OFF button (SW102) to power on and off the module.
•
GPIO1 button (SW101) for future applications.
•
Led (DL101) for device status indication.
NOTE: The Philips 74LVC1G08GW must be placed close to the GM862 connector; the length of the line
between CAMERA connector and MOLEX 50 PIN of GM862 must be max 5cm anyway.
NOTE: The CMOS cameras must be removed when the GPIO pins are used for I/O purpose.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 44 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
8.2 Camera Transchip
The GM862-QUAD provides a direct support for Transchip digital cameras with the following
characteristics:
Type:
TRANSCHIP TC5747
Technology:
CMOS COLOR camera
Max picture size:
VGA 480x640 pixels landscape
Output format:
JPEG
Sensitivity:
4 Lux
8.2.1Camera interface connectors
The 50-pins Molex connector of the module and a 24 pins ZIF connector for the CMOS camera
provide the interface connection between GM862 and Transchip camera.
TC5747MF24L
Molex 52991-0508 GM862
Pin
Signal
I/O
46
GPIO3
Notes
Pin
Signal
I/O
I2C bus serial clock
SCLK
Ground
AGND
External 2.8V Regulator enable
controlled by CAM_PWR_ON pin
AVDD28*
Camera Reset
RESET_N
Clock
CLK_IN**
Ground
DGND
n.c
DOUT_0
I/O
n.c
DOUT_1
I/O
n.c
DOUT_2
I/O
n.c
10
DOUT_3
I/O
n.c
11
DOUT_4
I/O
n.c
12
DOUT_5
I/O
n.c
13
DOUT_6
I/O
n.c
14
DOUT_7
I/O
n.c
15
DOUT_8
I/O
PD(6)
2-4-6
GND
50
GPIO7
CAM_PWR_ON
34
GPIO9
PD(1)
25
MON1
MON1_CAM
2-4-6
GND
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 45 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
50
n.c
16
VCLKOUT
n.c
17
VALIDH
n.c
18
VALIDV
19
DVDD28
20
SDIN
I/O
Ground
21
PS1
Camera power type selector
22
PS2
Ground
23
SHIELD
Flash Enable
24
LED_CTRL
GPIO7
CAM_PWR_ON
47
GPIO4
External 2.8V Regulator enable
controlled by CAM_PWR_ON pin
I/O I2C bus serial data
IICSDA_CAM
2-4-6
GND
32
GPIO8
PD(0)
2-4-6
GND
Filter the AVDD28.
Use a Buffer between module clk out, MON1_CAM and camera clk in, CLK_IN.
***
Non-connected.
**
Camera Socket Connector
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 46 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
8.2.2EVB for Agilent and Transchip camera support
In order to interface the Telit GM862 with a CMOS camera, Telit has developed an evaluation
board. The EVK allow connecting all Telit modules through 2 connectors of 40 pins each.
The I2CBUS DUAL CAMERA board is plugged in the 2 connectors of 30 pins each on the module
board.
CAMERA
BOARD
MODULE
BOARD
MAIN
BOARD
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 47 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
8.2.3Block Diagram for supported cameras
CAMERA AGILENT
GND
DVDD
IICSDA_CAM
IICSCL_CAM
CAM_PWR_ON
CAM_DRDY
PD[7]
PD[6]
PD[5]
PD[4]
PD[3]
PD[2]
PD[1]
PD[0]
CAM_SYNC
CAM_CLK
GND
DVDD
10
11
12
13
14
15
16
17
18
AVDD
CAMERA TRANSCHIP
PD[6]
GND
AVDD
PD[1]
CAM_CLK
GND
DVDD
IICSDA_CAM
GND
PD[0]
GND
GND
MON1_CAM
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
CAM_CLK
The numbers on the left side of the Camera’s connectors refers to Module Connector’s pin number.
DVDD is an external power supply of 2.8V, controlled or gated by pin CAM_PWR_ON.
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 48 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
8.2.4 Schematic Diagrams for supported cameras
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 49 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 50 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
8.2.5Example usage script for camera
Camera setting: (shown here are the defaults ones)
>AT#CAMSEL=0
(camera selection: 0-auto, 1-agilent, 2-transchip)
OK
>AT#CMODE=0
(camera mode: 0-day, 1-night)
OK
>AT#CAMQUA=0
(camera quality: 0-low, 1-medieum, 2-high)
OK
>AT#CAMRES=0
(camera resolution: 0-VGA, 1-QVGA, 2-QQVGA)
OK
>AT#CAMCOL=0*
(camera color: 0-color, 1-grayscale)
OK
>AT#CAMZOOM=0
(camera zoom: 0-x1, 1-x2, 2-x4)
OK
>AT#CAMTXT=0*
(camera timestamp: 0-no, 1-time only, 2-data only, 3-time&data)
OK
Taking an reading a photo:
>AT#CAMEN=1
(camera ON)
OK
>AT#TPHOTO
(take photo)
OK
>AT+OBJL?
(see photo dimension)
#OBJL: Snapshot,38900
(where 38900 is the file dimension in bytes of the photo taken)
OK
>AT#RPHOTO
(download the photo)
…data…..
(where …data… Correspond to the photo data in binary)
OK
>AT#TPHOTO
OK
>AT#RPHOTO
Repeating photo capture and download n times
…data…..
OK
>AT#CAMEN=O
(camera OFF)
*only Transchip camera
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 51 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
9 Document Change Log
Revision
Date
Changes
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 52 of 69
Telit GM862-QUAD/-QUAD-PY
Hardware User Guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
10 Annex A - EVK schematics
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 53 of 69
SO104
GND
10%
81
11
WARNING!!!!
Max current limit must be properly
set for the size of battery in use
Keep max current around 1/2 of
battery pack capacity
E.g. 1000mAh -> 500 mA max
Curr. limit is given by R102 to R105
DPAK-2S
2SJ387S
Q102
CR32
10%
4.7nF
X7R
50V
0603
FCMM0502
4.7
C101
CR32
10%
6 Vcc
4.7
CR32
BATTERY CHARGER INPUT
10%
CURRENT UNLIMITED
4.7
4.7
CR32
R105 R104 R103 R102
13
R107
680
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
BC857B
WARNING!!!!
Care must be taken to ensure
that the right polarity in the
power input is respected!
DO NOT Supply power when the
Battery is not connected
Otherwise GM862 may be damaged!
SMB
U34
5.6K
3Fs
SOT-23
STPS340U
5%
0603
R106
5%
0603
Current Limiting Circuit
D107
current limit: 500 mA
Q101
R101
10K
5%
0603
GND
CURRENT LIMITED
BATTERY CHARGER INPUT
4.5 - 10 Vcc
FCMM0502
GND
FAULT
1K
5%
0603
PLCC2
RED
Li - Ion battery charger
R113
1K
5%
0603
PLCC2
YELLOW
DL103
R112
1K
5%
0603
R116
R108
5%
0603
5%
LR32
R110
4.3K
DL101
LY-T670HK
R109
0.1
PLCC2
YELLOW
DL102
LS-T670HK
noMount=YES
R114
ON CHARGE
CHARGER PRESENCE
SO103
11
12
10
R115
47nF
X7R
50V
0603
LTC1730EGN-4
14
5%
0603
C105
max current ~ 1 A
1uF
35V
CONT-A
C102
U101
5%
0603
LY-T670HK
10K
CHRG
VCC
ACPR
SENSE
FAULT
GATE
GND
+VBATT
002:11D
NTC/SHDN
BAT
SEL
GND_1
TIMER
GND_8
NC_7
GND_9
NC_14
GND_16
SO101
13
FCMM0502
15
16
C103
D106
220pF
X7R
50V
0603
SOD123
STPS140Z
GND
C104
GND
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
max voltage 4,2V (Li-Ion)
GND
suggested capacity: 1000mAh
5%
0603
GND
GND
68nF
X7R
50V
0603
10k NTC
Temperature sensor
WARNING!!!!
When using battery care must be
taken to ensure that the right
polarity is respected!
PL101
FCMM0502
SO102
GND
1215061-03F
GND
NTC enabled
NTC disabled
WARNING!!!!
For a proper battery temperature
sensing the Termistor should be
placed on the battery pack.
BATTERY LI-ION
3,7V(Li-Ion) Nominal
R111
10K
Temperature sensing control
5%
0603
GND
MODIFY
DATE
WARNING!!!!
When the temperature sensing is disabled
the charger must be powered ONLY if the
battery temperature is within the charging
DESCRIPTION
PATH /home/users/area
OT101
OT102
OT103
range 0 - 50 C.
OT104
FILE NAME
EVK for GM862/S1
cs944b.cir
Mod. 067 rev.0 03/01
PROJECT
Deperini F.
FORM
ANNOTATION
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
A3
BATTERY CHARGE CONTROL
301101
Otherwise the battery may explode!
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
Mobile Terminals S.p.A.
PROJECT
0208
SHEET N.
OF SHEETS
page 54 of 69
10
DRAWING CODE
30208SE10944b
13
81
11
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
+5V input linear regulator
U201
SO201
LT1528CQ
FCMM0502
+5V INPUT
4,5V-8 Vcc
DZ201
D205
6KA24
STPS140Z
6KA24
GND
SOD123
noMount=YES
C203
C202
39nF
X7R
25V
0603
10uF
V_IN
V_OUT
C201
100uF
SHDN*
GND
SENSE
10V
CONT-D
R202
47
GND_1
35V
CONT-E
5%
0603
GND
GND
GND
GND
GND
GND
R201
WARNING!!!!
Care must be taken to ensure
that the right polarity in the
power input is respected!
330
5%
0603
+5V/+12V select
Battery/Regulator select
GND
+3.7V
U202
+12V
+12V INPUT
8-15,8V Vcc
BOOST
DZ202
D206
6KA24
GND
STPS140Z
6KA24
SOD123
noMount=YES
GND
C207
C206
39nF
X7R
25V
0603
10uF
VSW
SHDN*
SENSE
GND_1
VC
GND_2
35V
CONT-E
GND
SCD-80
1215061-03F
PL202
L201
10uH
+VBATT
001:9C
DO3316
C204
100uF
D201
STPS140Z
C208
10V
CONT-D
R203
2.7K
SOD123
1.5nF
X7R
50V
0603
5%
GND
0603
GND
GND
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
VIN
470nF
X5R
6.3V
0603
PL201
C209
LT1374CR
SO202
FCMM0502
BAT62-02W
D202
1215061-03F
GND
GND
GND
R204
4.7K
5%
0603
GND
+12V input switching regulator
MODIFY
DATE
DESCRIPTION
PATH /home/users/area
FILE NAME
EVK for GM862/S1
cs944b.cir
Mobile Terminals S.p.A.
Mod. 067 rev.0 03/01
PROJECT
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
Deperini F.
FORM
ANNOTATION
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
A3
+5V/+12V INPUT POWER REGULATORS
301101
PROJECT
0208
SHEET N.
OF SHEETS
page 55 of 69
10
DRAWING CODE
30208SE10944b
13
81
11
+3.7V
PL302
1215061-02F
RS232 LEVEL TRANSLATOR POWER SELECTION
C305
12
C113
C2+
15
14
V-
L316
787200-1
LQG18HN39NJ00
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
C303
SO301
L314
LQG18HN39NJ00
39nH
LQG18
C2-
GND
L315
LQG18HN39NJ00
39nH
LQG18
C301
C1+
11
V+
TO RS232
C302
10
VCC
0603
10V
X7R
220nF
C304
0603
10V
X7R
220nF
0603
10V
X7R
220nF
0603
16V
X7R
100nF
U301
ICL3207CA
SSOP-24
0603
10V
X7R
220nF
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
L313
LQG18HN39NJ00
39nH
LQG18
L312
24
LQG18HN39NJ00
39nH
LQG18
20
39nH
LQG18
T1_OUT
T1_IN
T2_OUT
T2_IN
TR3_OUT
T3_IN
T4_OUT
T4_IN
T5_OUT
T5_IN
18
19
21
L311
LQG18HN39NJ00
L310
L309
23
LQG18HN39NJ00
39nH
LQG18
LQG18HN39NJ00
39nH
LQG18
16
39nH
LQG18
R1_IN
R1_OUT
R2_IN
R2_OUT
RTS
004:6D
RX_PROG
004:5D
DTR
004:6D
22
17
R3_IN
DCD
004:6D
TX_PROG
004:6D
DSR
004:5D
CTS
004:5D
RING
004:5D
R3_OUT
GND_8
GND
GND
C321
C322
C320
C323
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
GND
GND
GND
GND
C319
39pF
COG
50V
0603
C324
C318
C325
C317
C326
C316
C327
C315
C328
C314
C329
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
+3.7V UART
PL301
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
1615061-10F
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
GND
L301
LQG18HN39NJ00
L302
LQG18HN39NJ00
39nH
LQG18
39nH
LQG18
L303
LQG18HN39NJ00
L304
LQG18HN39NJ00
39nH
LQG18
L305
L306
L307
L308
LQG18HN39NJ00
LQG18HN39NJ00
39nH
LQG18
LQG18HN39NJ00
LQG18HN39NJ00
39nH
LQG18
39nH
LQG18
39nH
LQG18
39nH
LQG18
10
GND
C330
C331
C332
C333
C334
C335
C336
C337
C306
C307
C308
C309
C310
C311
C312
C313
39pF
COG
50V
0603
39pF
COG
50V
0603
39pF
COG
50V
0603
39pF
COG
50V
0603
39pF
COG
50V
0603
39pF
COG
50V
0603
39pF
COG
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
MODIFY
DATE
DESCRIPTION
PATH /home/users/area
FILE NAME
EVK for GM862/S1
cs944b.cir
Mobile Terminals S.p.A.
Mod. 067 rev.0 03/01
PROJECT
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
Deperini F.
FORM
ANNOTATION
301101
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
RS232 LEVEL TRANSLATOR AND UART INPUT/OUTPUT
PROJECT
0208
SHEET N.
OF SHEETS
31
page 56 of 69
DRAWING CODE
30208SE10944b
A3
13
81
11
L401
0.35
+3.7V
4312-020
noMount=YES
L403
220
C405
C404
100nF
X7R
16V
0603
100pF
COG
50V
0603
L404
220
BLM21
SO402
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
GPI01
STAT_LED
RX_PROG
CTS
RING
DSR
DCD
TX_PROG
DTR
RTS
GND
PWR_GND
+3.7V
100pF
COG
50V
0603
C401
PL401
33pF
COG
50V
0603
GND_EXT
53748-0504
4312-020
GND
MIC_MT+
MIC_HF+
MIC_MTON
START
RESET
GPI02
AXE
C402
100nF
X7R
16V
0603
0.35
4773541130470
EAR_HF+
EAR_MTEAR_HFEAR_MT+
GND
MIC_HF-
C403
L402
S1 CONNECTOR
noMount=YES
GM862 CONNECTOR
BLM21
EAR_HF+
EAR_MTEAR_HFEAR_MT+
10
MIC_HFMIC_MT+
MIC_HF+
MIC_MT-
13
11
12
10
14
11
15
12
16
13
17
AXE
14
18
15
19
16
20
17
21
18
22
19
23
20
24
21
25
22
26
23
27
24
28
25
29
26
30
27
31
28
32
29
33
30
34
35
36
GND
37
38
39
41
SIMRST
SIMCLK
CCIN
SIMVCC
40
42
43
44
46
C4
C3
C2
C1
45
EAR_HF+
EAR_MTEAR_HFEAR_MT+
MIC_HFMIC_MT+
MIC_HF+
MIC_MTON
AXE
SIMIO
RX_PROG
START
SIMVCC
RESET
SIMRST
TEST_32KHz
SIMCLK
CCIN
GPI02
CTS
RING
GPI01
JP101
DSR
JP102
TX_TRACE
DCD
TX_PROG
JP104
STAT_LED
JP103
RX_TRACE
JP105
DTR
JP106
RTS
SO401
52827-0611
49
50
C8
C7
48
C6
C5
SIM_CARD
GPIO3
005:11D
TX_TRACE
010:9B
RESET
005:9B
START
005:3D
RTS
003:10C
DTR
003:10C
STAT_LED
005:9C
DCD
003:10B
TX_PROG
003:10B
DSR
003:10B
RING
003:10B
CTS
003:10B
GPIO1
005:7C;006:10D
GPIO2
005:6A
RX_PROG
003:10C
AXE
005:7E
ON
005:10A
MIC_MT006:10C
MIC_HF+
007:11C
MIC_MT+
006:10B
MIC_HF007:11D
EAR_MT+
006:10E;008:10B
EAR_HF008:10D;009:11C
EAR_MT006:10D;008:10B
SIMIO
RX_TRACE
010:9C
GPIO4
005:11D
GND
EAR_HF+
008:10D;009:11B
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
47
GPIO5
005:11D
GPIO6
005:11D
GPIO7
005:11D
MODIFY
DATE
DESCRIPTION
PATH /home/users/area
FILE NAME
EVK for GM862/S1
cs944b.cir
Mobile Terminals S.p.A.
Mod. 067 rev.0 03/01
PROJECT
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
Deperini F.
FORM
ANNOTATION
301101
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
A3
GM862 & S1 CONNECTORS
PROJECT
0208
SHEET N.
OF SHEETS
page 57 of 69
10
DRAWING CODE
30208SE10944b
13
81
11
+3.7V
+3.7V
R503
560
R510
5%
1215061-02F
TP501
22K
PL506
0603
5%
0603
PLCC2
YELLOW
GREEN - GPIO2 LED
GPIO2 OUTPUT
ON
004:4D
GPIO2
004:5D
LY-T670HK
DL503
ON BUTTON
+3.7V
TC7S08FU
C501
Q503
U501
47K
SOT-323
WEs
47K
VCC_1
GND_1
SKHHAL
Q506
BCR148W
47K
U501
SOT-323
WEs
TC7S08FU
+3.7V
R505
560
GND
GND
RESET BUTTON
PL504
GND
SW501
MUTE CONTROL SELECT
5%
0603
E2
GPIO2
1215061-02F
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
BCR148W
100nF
Y5V
16V
0603
SW502
+3.7V
47K
GND
PLCC2
YELLOW
SKHHAL
GREEN - STEREO MUTE LED
LY-T670HK
RESET
004:7D
MUTE
008:10B;008:10D;009:11C
DL505
GND
+3.7V
+3.7V
R502
560
Q507
BCR148W
47K
R501
5%
0603
100
47K
SOT-323
WEs
5%
0603
PLCC2
YELLOW
GREEN - GPIO1 LED
PLCC2
YELLOW
+3.7V
LY-T670HK
YELLOW - STAT LED
DL502
+12V
GND
R508
R506
BCR148W
47K
SOT-323
WEs
47K
STAT_LED
004:6D
GPIO1
004:5D;006:10D
47K
PL507
SOT-323
WEs
CAR STEREO
MUTE CONTROL
GPIO (GPRS) CONNECTOR
GND
PL508
47K
Q508
1215061-02F
noMount=YES
GPIO2
Q502
BCR148W
1215061-02F
EXTERNAL ACCESSORIES
DL501
5%
0603
5%
0603
PL502
CAR STEREO MUTE OUTPUT
LY-T670HK
1K
10K
1615061-10F
L505
LQG18HN39NJ00
PL505
GND
LQG18HN39NJ00
GND
LQG18HN39NJ00
GND
LQG18HN39NJ00
10
PL501
+3.7V
1215061-02F
EXTERNAL ACCESSORIES
START
004:6D
39nH
GPIO6
004:10E
39nH
LQG18
L501
C510 LQG18
C511
C504
C505
C506
C507
C502
C503
C508
C509
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
39pF
COG
50V
0603
1nF
X7R
50V
0603
GPIO7
004:10E
R504
560
POWER ON OUTPUT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
5%
0603
GND
PLCC2
YELLOW
GREEN - AXE LED
LY-T670HK
+3.7V
DL504
R509
MODIFY
10K
5%
0603
DATE
PL503
1215061-02F
EXTERNAL ACCESSORIES
Q504
SENSE INPUT
R507
SOT-323
WEs
FILE NAME
Mod. 067 rev.0 03/01
GND
GND
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
EVK for GM862/S1
cs944b.cir
Mobile Terminals S.p.A.
5%
0603
DESCRIPTION
PATH /home/users/area
BCR148W
47K
47K
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
LQG18HN39NJ00
GPIO5
004:10D
39nH
LQG18
L503
GPIO4
004:10D
39nH
LQG18
L504
GPIO1 INPUT
GPIO3
004:10D
39nH
LQG18
L502
1215061-02F
PROJECT
AXE
004:4D
Deperini F.
FORM
ANNOTATION
301101
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
AUX PINS, STATE LEDS AND ON/RESET BUTTONS
PROJECT
0208
SHEET N.
OF SHEETS
page 58 of 69
10
DRAWING CODE
30208SE10944b
A3
13
81
11
BALANCED MICROPHONE POLARIZATION
+3V_INT_MIC_BAL
R601
10K
5%
0603
Q601
BALANCED MICROPHONE BUFFER +24 dB
DECOUPLING CAPACITORS
C601
SO605
IO
INT_MICGND
GND
5%
0603
100nF
Y5V
16V
0603
C608
10K
100nF
Y5V
16V
0603
U602
TS3V912ID
V+OUT
V-
BALANCED
SINGLE ENDED
INT MIC POWER SELECTION
GND
GND
C636
GND
J01001A1944
GND
100nF
Y5V
16V
0603
1nF
X7R
50V
0603
1215061-03F
54 32
GND
5%
0603
C615
1nF
X7R
50V
0603
PL603
+3V_MIC
100pF
COG
50V
0603
5%
0603
C614
GND
5%
0603
39pF
COG
50V
0603
5%
0603
GND
10K
C613
39pF
COG
50V
0603
47K
+3V_INT_MIC_BAL
+3V_INT_MIC_BAL
R607
C612
1K
100nF
Y5V
16V
0603
GND
100nF
Y5V
16V
0603
R603
39nH
LQG18
R615
+3V_INT_MIC_SINGLE
C603
LQG18HN39NJ00
C627
C609
0603
16V
Y5V
100nF
0603
16V
Y5V
100nF
L601
GND
V+OUT
V4
1 5
LGK2009-02
TS3V912ID
39nH
LQG18
C628
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
L602
LQG18HN39NJ00
BALANCED
INTERNAL MIC
GND
C602
5%
0603
SO601
R605
SIGNAL FILTERING
1K
U602
54 32
R602
GND
5%
0603
150K
100pF
COG
5%
50V
0603
0603
IO
47K
C637 R604
J01001A1944
INT_MIC+
C630
0603
16V
Y5V
100nF
SO606
GND
LGK2009-0201
+3V_INT_MIC_BAL
R616
4V
CONT-R
C618
+3V_INT_MIC_BAL
4.7uF
150K
SOT-323
1Fs
R606
BC847BW
MIC_MT+
004:4D
SINGLE ENDED MICROPHONE POLARIZATION
PL602
+3V_INT_MIC_SINGLE
1615061-08F
R609
10K
Q602
47K
5%
0603
GND
5%
0603
GND
47K
95001-6881
5%
0603
BOOT RX
100nF
Y5V
16V
0603
L606
L605
BOOT TX
LQG18HN39NJ00
EAR-
5%
0603
0603
5%
82K
R618
470K
5%
0603
100nF
Y5V
16V
0603
47K
GND
GND
GPIO1
004:5D;005:7C
39nH
LQG18
EAR_MT004:3D;008:10B
L604
LQG18HN39NJ00
EAR+
C631
R620
39nH
LQG18
MICRMICR+
GND
10K
R617
GND
LQG18HN39NJ00
R619
5%
0603
C633
GND
HOOK
0603
5%
47K
SIGNAL FILTERING
R621
GND
noMount=YES
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
R612
54 3 2
+3V_MIC
TS3V912ID
220pF
X7R
50V
0603
IO
U603
V+
OUT
V-
C634
J01001A1944
INT_MIC
C626
SO604
0603
16V
Y5V
100nF
+3V_INT_MIC_SINGLE
SO603
GND
Y5V
16V
0603
+3V_INT_MIC_SINGLE
GND
100nF
47K
82K
R613
100nF
Y5V
16V
0603
5%
0603
C625
GND
LGK2009-02
HANDSET V125
INT MIC SELECTION
MIC_MT004:4D
C606
1nF
X7R
50V
0603
GND
100nF
Y5V
16V
0603
10K
R611
220pF
X7R
50V
0603
1 5
TS3V912ID
V+OUT
V-
C635 R610
C616
39pF
COG
50V
0603
C632
0603
16V
Y5V
100nF
C607
U603
SO602
LGK2009-0201
C604
0603
16V
Y5V
100nF
39nH
LQG18
C611
L603
SINGLE ENDED
GND
5%
0603
GND
LQG18HN39NJ00
DECOUPLING CAPACITORS
SIGNAL FILTERING
2.2K
SINGLE ENDED
100nF
Y5V
16V
0603
+3V_INT_MIC_SINGLE
R614
4V
CONT-R
C617
4.7uF
R608
+3V_INT_MIC_SINGLE
C610
5%
0603
BALANCED
SOT-323
1Fs
SINGLE ENDED
INTERNAL MIC
SINGLE ENDED MICROPHONE BUFFER +24 dB
BC847BW
BALANCED
5%
0603
EAR_MT+
004:3D;008:10B
39nH
LQG18
GND
C622
39pF
COG
50V
0603
C621
39pF
COG
50V
0603
C624
39pF
COG
50V
0603
C619
C620
C623
1nF
X7R
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
MODIFY
DATE
U601
LP2980AIM5X-3_0
+3V_MIC
+3.7V
GND
V_OUT
C605
10uF
35V
CONT-E
GND
NC
GND
GND
GND
GND
GND
DESCRIPTION
PATH /home/users/area
V_IN
ON-OFF
FILE NAME
EVK for GM862/S1
cs944b.cir
Mod. 067 rev.0 03/01
L02A
MA05B
Mobile Terminals S.p.A.
GND
PROJECT
Deperini F.
301101
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
GND
MICROPHONE POLARIZATION REGULATOR
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
FORM
ANNOTATION
INTERNAL MICROPHONE SECTION
PROJECT
SHEET N.
0208
OF SHEETS
page 59 of 69
10
DRAWING CODE
30208SE10944b
A3
13
81
11
BALANCED MICROPHONE POLARIZATION
+3V_EXT_MIC_BAL
R705
10K
5%
0603
Q702
BC847BW
DECOUPLING CAPACITORS
SOT-323
1Fs
BALANCED MICROPHONE BUFFER +10 dB
C702
4.7uF
0603
GND
NOISE FILTERING
1nF
X7R
50V
0603
1nF
X7R
50V
0603
33K
BALANCED
SINGLE ENDED
+3V_EXT_MIC_BAL
TS3V912ID
V+
V-OUT
U702
IO
EXT_MIC54 3 2
5%
0603
J01001A1944
GND
33K
GND
R710
GND
470pF
X7R
50V
0603
GND
C728
GND
GND
SO704
GND
GND
100nF
Y5V
16V
0603
C708
1215061-03F
EXT MIC POWER SELECTION
C713
39pF
COG
50V
0603
C707
5%
0603
5%
0603
39pF
COG
50V
0603
5%
0603
39nH
LQG18
R706
1K
C705
47K
C721
C703
0603
16V
Y5V
100nF
R703
C711
0603
16V
Y5V
100nF
L702
GND
5%
0603
100nF
Y5V
16V
0603
1 5
LQG18HN39NJ00
R712
470pF
X7R
50V
0603
C718
39nH
LQG18
GND
+3V_EXT_MIC_SINGLE
C729 R709
C710
LQG18HN39NJ00
LGK2009-02
PL702
+3V_MIC
10K
BALANCED
EXTERNAL MIC
0603
16V
Y5V
100nF
L703
+3V_EXT_MIC_BAL
0603
SO701
LGK2009-0201
V+
OUT
V-
C712
10K
1K
TS3V912ID
5%
0603
R707
R702
U702
100nF
Y5V
16V
0603
54 3 2
GND
5%
100nF
Y5V
16V
0603
+3V_EXT_MIC_BAL
47K
5%
GND
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
R713
C717
IO
EXT_MIC+
C722
SO705
J01001A1944
0603
16V
Y5V
100nF
+3V_EXT_MIC_BAL
4V
CONT-R
MIC_HF+
004:4D
GND
SINGLE ENDED MICROPHONE POLARIZATION
PL701
1615061-08F
+3V_EXT_MIC_SINGLE
BALANCED
R704
SINGLE ENDED MICROPHONE BUFFER +10 dB
5%
0603
+3V_EXT_MIC_SINGLE
C701
GND
1nF
X7R
50V
0603
GND
GND
5%
0603
5 4 32
R715
100nF
Y5V
16V
0603
47K
100nF
Y5V
16V
0603
C714
C715
5%
0603
470K
5%
0603
C725
100nF
Y5V
16V
0603
5%
5%
0603
R720
GND
C720
TS3V912ID
10K
R718
J01001A1944
C724
5%
0603
0603
16V
Y5V
100nF
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
+3V_EXT_MIC_SINGLE
GND
U701
V+
OUT
V-
100nF
Y5V
16V
0603
47K
IO
R717
SO703
MIC_HF004:3D
GND
+3V_EXT_MIC_SINGLE
GND
EXT_MIC
15K
47K
5%
0603
100nF
Y5V
16V
0603
LGK2009-02
GND
EXT MIC SELECTION
R711
R716
1nF
X7R
50V
0603
C706
C719
5.6K
1 5
39pF
COG
50V
0603
R719
SINGLE ENDED
EXTERNAL MIC
C704
C723
0603
16V
Y5V
100nF
SO702
TS3V912ID
SINGLE ENDED
39nH
LQG18
LGK2009-0201
U701
V+
OUT
V-
C727
L701
LQG18HN39NJ00
3.3nF
X7R
50V
0603
NOISE FILTERING
5%
0603
DECOUPLING CAPACITORS
10K
4V
CONT-R
C726
5%
0603
5%
0603
4.7uF
2.2K
GND
R708
R701
SINGLE ENDED
47K
C709
R714
0603
16V
Y5V
100nF
SOT-323
1Fs
C716
Q701
BC847BW
BALANCED
+3V_EXT_MIC_SINGLE
100nF
Y5V
16V
0603
10K
0603
GND
GND
GND
GND
MODIFY
DATE
DESCRIPTION
PATH /home/users/area
FILE NAME
EVK for GM862/S1
cs944b.cir
Mobile Terminals S.p.A.
Mod. 067 rev.0 03/01
PROJECT
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
Deperini F.
FORM
ANNOTATION
301101
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
A3
EXTERNAL MICROPHONE SECTION
PROJECT
0208
SHEET N.
OF SHEETS
71
page 60 of 69
DRAWING CODE
30208SE10944b
13
81
11
10pF
COG
50V
0603
5%
0603
56K
R802
C803
INTERNAL EAR AMPLIFIER +6dB
NOISE FILTERING
SO801
C804
J01001A1944
39pF
COG
50V
0603
IO
54 32
220uF
INT_EAR-
C820
SO806
C805
39nH
LQG18
39pF
COG
50V
0603
C806
C807
1nF
X7R
50V
0603
1nF
X7R
50V
0603
C821
C822
100nF
Y5V
16V
0603
100nF
Y5V
16V
0603
R807
GND
100nF
Y5V
16V
0603
5%
0603
0603
EAR_MT004:3D;006:10D
C801
1uF
X5R
6.3V
0603
GND
MUTE
005:5B;008:10D;009:11C
PL803
1215061-03F
15
5%
GND
IN+
EAR_MT+
004:3D;006:10E
C802
GND
GND
BYPASS
GND
R806
15
GND
GND
VC2
100nF
Y5V
16V
0603
LQG18HN39NJ00
IN-
VC1 SHUTDOWN
C830
L801
GND
CONT-E
16V
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
LGY650X
VDD
100nF
Y5V
16V
0603
C829
39nH
LQG18
5%
0603
LM4862M
56K
U801
+3.7V
5%
0603
L802
LQG18HN39NJ00
1M
BRIDGED
INTERNAL EAR
R812 R801
LGY6502-0600
MUTE CONTROLLED
ALWAYS ON
GND
GND
GND
AMPLI POWER CONTROL
GND
NOISE FILTERING
SO802
LGY6502-0600
L803
LGY650X
220uF
CONT-E
16V
LQG18HN39NJ00
39nH
LQG18
C819
SINGLE ENDED
INTERNAL EAR
C808
GND
C809
39pF
COG
50V
0603
SO805
J01001A1944
1nF
X7R
50V
0603
IO
INT_EAR+
54 32
GND
GND
GND
10pF
COG
50V
0603
5%
0603
100K
R803
C817
LOW VOLTAGE EXTERNAL EAR AMPLIFIER +12dB
NOISE FILTERING
SO803
C811
C810
5 4 32
C813
C815
1nF
X7R
50V
0603
1nF
X7R
50V
0603
C824
CONT-E
16V
IO
220uF
J01001A1944
EXT_EAR-
39pF
COG
50V
0603
39pF
COG
50V
0603
SO808
39nH
LQG18
C825
C826
100nF
Y5V
16V
0603
100nF
Y5V
16V
0603
R809
R810
15
GND
GND
GND
15
GND
5%
0603
VC2
BYPASS
GND
IN+
100nF
Y5V
16V
0603
C827
EAR_HF+
004:3D;009:11B
EAR_HF004:3D;009:11C
C816
100nF
Y5V
16V
0603
GND
GND
IN-
VC1 SHUTDOWN
100nF
Y5V
16V
0603
LQG18HN39NJ00
VDD
C828
L804
GND
5%
0603
LM4862M
5%
0603
39nH
LQG18
LGY650X
C818
1uF
X5R
6.3V
0603
GND
MUTE
005:5B;008:10B;009:11C
PL804
1215061-03F
GND
5%
0603
MUTE CONTROLLED
ALWAYS ON
GND
GND
AMPLI POWER CONTROL
GND
NOISE FILTERING
SO804
LGY6502-0600
L806
SINGLE ENDED
EXTERNAL EAR
220uF
LGY650X
DATE
C812
GND
SO807
J01001A1944
MODIFY
39nH
LQG18
C823
LQG18HN39NJ00
CONT-E
16V
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
U802
+3.7V
56K
1M
L805
LQG18HN39NJ00
BRIDGED
EXTERNAL EAR
R811 R804
LGY6502-0600
39pF
COG
50V
0603
C814
1nF
X7R
50V
0603
IO
EXT_EAR+
5 4 32
DESCRIPTION
PATH /home/users/area
FILE NAME
EVK for GM862/S1
cs944b.cir
Mobile Terminals S.p.A.
GND
GND
GND
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
Mod. 067 rev.0 03/01
FORM
ANNOTATION
PROJECT
Deperini F.
301101
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
INTERNAL EAR (HANDSET)/ EXTERNAL EAR (HANDSFREE)
PROJECT
SHEET N.
0208
OF SHEETS
81
page 61 of 69
DRAWING CODE
30208SE10944b
A3
13
81
11
HIGH POWER EXT EAR AMPLIFIER (6W)
+12V
R901
U901
5%
0603
100nF
Y5V
16V
0603
5%
0603
10K
OUT+
15K
5%
IN+
220
R902
1.5nF
X7R
50V
0603
EAR_HF+
004:3D;008:10D
0603
L901
C913
R903
IN-
10K
C912
5%
0603
OUT-
R904
BLM21
100nF
Y5V
16V
0603
HIGH POWER BRIDGED
EXTERNAL EAR
MIN 8 OHM
VCC
220
FCMM0502
56K
TDA8943SF-N1 2
L902
SO901
noMount=YES
NOISE FILTERING
C911
ALL RIGHTS RESERVED
REPRODUCTION AND DISCLOSURE
FORBIDDEN
EAR_HF004:3D;008:10D
BLM21
GND
C905
C906
39pF
COG
50V
0603
1nF
X7R
50V
0603
1nF
X7R
50V
0603
GND
GND
noMount=YES
C904
noMount=YES
39pF
COG
50V
0603
noMount=YES
noMount=YES
C903
MODE 7
C902
C901
100nF
Y5V
16V
0603
1000uF
NC
GND
SOT110-1
PL901
GND
GND
GND
MUTE
005:5B;008:10B;008:10D
SVR
35V
18
1215061-03F
C910
C908
10uF
GND
100nF
Y5V
16V
0603
35V
CONT-E
MUTE CONTROLLED
ALWAYS ON
GND
GND
GND
AMPLI POWER CONTROL
NOTE:
TUTTI I DIRITTI RISERVATI
RIPRODUZIONE E DIVULGAZIONE
VIETATE
Heat Sink may be required
Refer to chip datasheet
MODIFY
DATE
DESCRIPTION
PATH /home/users/area
FILE NAME
EVK for GM862/S1
cs944b.cir
Mobile Terminals S.p.A.
Mod. 067 rev.0 03/01
PROJECT
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
Deperini F.
FORM
ANNOTATION
HIGH POWER EXTERNAL EAR (HANDSFREE)
301101
DRAWN
Serdi M.
041201
VERIFIED
Locatelli M.
041201
PROJECT
0208
SHEET N.
OF SHEETS
page 62 of 69
10
DRAWING CODE
30208SE10944b
A3
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 63 of 69
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 64 of 69
Telit GM862-QUAD Hardware User guide
1vv0300692, Rev. ISSUE#0, - 04/10/2005
11 Annex B - Camera EVB schematics
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 65 of 69
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 66 of 69
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 67 of 69
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 68 of 69
Reproduction forbidden without DAI Telecom written authorization – All Right reserved – Right of modification reserved
page 69 of 69

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2005:10:04 12:10:29+02:00
Create Date                     : 2005:10:04 12:10:29+02:00
Format                          : application/pdf
Title                           : Microsoft Word - 1vv0300692_GM862-QUAD Hardware User Guide_r0.doc
Creator                         : DanieleLu
Document ID                     : uuid:329c9f3d-5183-446e-8fe8-e6d7eaab58d1
Instance ID                     : uuid:ed8ae550-c83f-4d18-9627-31400a1b880c
Page Count                      : 69
Author                          : DanieleLu

EXIF Metadata provided by EXIF.tools