Telit Communications S p A HE910NA 2G/3.5G module, HE910-NAG; HE910-NAR; HE910-NAD User Manual HE910 Hardware User Guide
Telit Communications S.p.A. 2G/3.5G module, HE910-NAG; HE910-NAR; HE910-NAD HE910 Hardware User Guide
User_Guide_r18
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1731830 |
| Application ID | kaBbxAvEU806DILC3oFrww== |
| Document Description | User_Guide_r18 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 250.53kB (3131628 bits) |
| Date Submitted | 2012-06-28 00:00:00 |
| Date Available | 2012-12-20 00:00:00 |
| Creation Date | 2012-06-15 16:39:16 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2012-06-15 16:39:16 |
| Document Title | HE910 Hardware User Guide |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | F D |
HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 PRODUCT HE910 HE910-GA HE910-D HE910-EUR HE910-EUD HE910-EUG HE910-NAR HE910-NAD HE910-NAG Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 2 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 DISCLAIMER The information contained in this document is the proprietary information of Telit Communications S.p.A. and its affiliates (“TELIT”). The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Telit, is strictly prohibited. Telit makes every effort to ensure the quality of the information it makes available. Notwithstanding the foregoing, Telit does not make any warranty as to the information contained herein, and does not accept any liability for any injury, loss or damage of any kind incurred by use of or reliance upon the information. Telit disclaims any and all responsibility for the application of the devices characterized in this document, and notes that the application of the device must comply with the safety standards of the applicable country, and where applicable, with the relevant wiring rules. Telit reserves the right to make modifications, additions and deletions to this document due to typographical errors, inaccurate information, or improvements to programs and/or equipment at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this application note. All rights reserved. © 2011, 2012 Telit Communications S.p.A. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 3 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 INTRODUCTION ......................................................................................................................................................... 7 1.1 SCOPE ................................................................................................................................................................................ 7 1.2 AUDIENCE ........................................................................................................................................................................... 7 1.3 CONTACT INFORMATION, SUPPORT .......................................................................................................................................... 7 1.4 DOCUMENT ORGANIZATION ................................................................................................................................................... 8 1.5 TEXT CONVENTIONS .............................................................................................................................................................. 9 1.6 RELATED DOCUMENTS........................................................................................................................................................... 9 1.7 DOCUMENT HISTORY .......................................................................................................................................................... 10 OVERVIEW .............................................................................................................................................................. 11 HE910 MODULE CONNECTIONS ............................................................................................................................... 12 3.1 PIN-OUT ......................................................................................................................................................................... 12 3.1.1 LGA Pads Layout (HE910 and HE910-GA) .............................................................................................................. 18 3.1.2 LGA Pads Layout (HE910-D) ................................................................................................................................... 19 3.1.3 LGA Pads Layout (HE910-EUx and HE910-NAx) ..................................................................................................... 20 3.1.4 LGA Pads Layout (HE910-EUG and HE910-NAG) .................................................................................................... 21 HARDWARE COMMANDS ........................................................................................................................................ 22 4.1 TURNING ON THE HE910 ................................................................................................................................................... 22 4.2 TURNING OFF THE HE910 .................................................................................................................................................. 27 4.3 HE910 UNCONDITIONAL SHUTDOWN .................................................................................................................................... 29 4.4 HE910 RESET .................................................................................................................................................................. 32 POWER SUPPLY ....................................................................................................................................................... 35 5.1 POWER SUPPLY REQUIREMENTS ............................................................................................................................................ 35 5.2 POWER CONSUMPTION ....................................................................................................................................................... 36 5.3 GENERAL DESIGN RULES ...................................................................................................................................................... 37 5.3.1 Electrical Design Guidelines ................................................................................................................................... 37 5.3.2 Thermal Design Guidelines ..................................................................................................................................... 41 5.3.3 Power Supply PCB layout Guidelines ...................................................................................................................... 42 GSM/WCDMA RADIO SECTION ............................................................................................................................... 43 6.1 HE910 PRODUCT VARIANTS ................................................................................................................................................ 43 6.2 TX OUTPUT POWER ............................................................................................................................................................ 43 6.3 SENSITIVITY ....................................................................................................................................................................... 44 6.4 GSM/WCDMA ANTENNA REQUIREMENTS ............................................................................................................................ 44 6.5 GSM/WCDMA - PCB LINE GUIDELINES ................................................................................................................................ 45 6.6 GSM/WCDMA ANTENNA - INSTALLATION GUIDELINES ........................................................................................................... 46 6.7 ANTENNA DIVERSITY REQUIREMENTS ..................................................................................................................................... 47 GPS RECEIVER .......................................................................................................................................................... 48 7.1 GPS PERFORMANCES .......................................................................................................................................................... 48 7.2 GPS SIGNALS PINOUT ......................................................................................................................................................... 49 7.3 RF FRONT END DESIGN ....................................................................................................................................................... 49 7.3.1 RF Signal Requirements .......................................................................................................................................... 49 7.3.2 GPS Antenna Polarization ...................................................................................................................................... 50 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 4 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 7.3.3 GPS Antenna Gain .................................................................................................................................................. 51 7.3.4 Active versus Passive Antenna ............................................................................................................................... 51 7.3.5 GPS Antenna - PCB Line Guidelines ........................................................................................................................ 52 7.3.6 RF Trace Losses....................................................................................................................................................... 52 7.3.7 Implications of the Pre-select SAW Filter ............................................................................................................... 53 7.3.8 External LNA Gain and Noise Figure....................................................................................................................... 53 7.3.9 Powering the External LNA (active antenna) ......................................................................................................... 53 7.3.10 External LNA Enable ............................................................................................................................................. 54 7.3.11 Shielding ............................................................................................................................................................... 55 7.3.12 GPS Antenna - Installation ................................................................................................................................... 55 LOGIC LEVEL SPECIFICATIONS .................................................................................................................................. 56 8.1 RESET SIGNAL .................................................................................................................................................................... 57 USB PORT ................................................................................................................................................................ 58 9.1 USB 2.0 HS ...................................................................................................................................................................... 58 10 SPI PORT ................................................................................................................................................................. 59 10.1 SPI CONNECTIONS ............................................................................................................................................................ 60 11 SERIAL PORTS .......................................................................................................................................................... 61 11.1 MODEM SERIAL PORT 1 (USIF0) ................................................................................................................................... 62 11.2 MODEM SERIAL PORT 2 (USIF1) ................................................................................................................................... 64 11.3 RS232 LEVEL TRANSLATION................................................................................................................................................ 65 12 AUDIO SECTION OVERVIEW .................................................................................................................................... 67 12.1 ELECTRICAL CHARACTERISTICS ............................................................................................................................................. 67 12.1.1 CODEC Examples .................................................................................................................................................. 67 13 GENERAL PURPOSE I/O ........................................................................................................................................... 68 13.1 GPIO LOGIC LEVELS .......................................................................................................................................................... 69 13.2 USING A GPIO PAD AS INPUT ........................................................................................................................................... 70 13.3 USING A GPIO PAD AS OUTPUT ........................................................................................................................................ 70 13.4 INDICATION OF NETWORK SERVICE AVAILABILITY ..................................................................................................................... 71 13.5 RTC BYPASS OUT ............................................................................................................................................................. 72 13.6 EXTERNAL SIM HOLDER IMPLEMENTATION ........................................................................................................................... 72 13.7 VAUX POWER OUTPUT..................................................................................................................................................... 72 13.8 ADC CONVERTER ............................................................................................................................................................. 73 13.8.1 Description ........................................................................................................................................................... 73 13.8.2 Using ADC Converter ............................................................................................................................................ 73 14 MOUNTING THE HE910 ON THE APPLICATION ........................................................................................................ 74 14.1 GENERAL ........................................................................................................................................................................ 74 14.2 MODULE FINISHING & DIMENSIONS ..................................................................................................................................... 74 14.3 RECOMMENDED FOOT PRINT FOR THE APPLICATION ................................................................................................................. 76 14.4 STENCIL .......................................................................................................................................................................... 77 14.5 PCB PAD DESIGN .............................................................................................................................................................. 77 14.6 PCB PAD DIMENSIONS ....................................................................................................................................................... 78 14.7 SOLDER PASTE .................................................................................................................................................................. 80 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 5 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 14.7.1 HE910 Solder reflow ............................................................................................................................................. 80 14.8 PACKING SYSTEM .............................................................................................................................................................. 82 14.9 MOISTURE SENSITIVITY ...................................................................................................................................................... 84 15 SAFETY RECOMMANDATIONS ................................................................................................................................. 85 16 CONFORMITY ASSESSMENT ISSUES ......................................................................................................................... 86 16.1 1999/5/EC DIRECTIVE ..................................................................................................................................................... 86 16.2 FCC/IC REGULATORY NOTICES ............................................................................................................................................ 90 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 6 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The aim of this document is the description of some hardware solutions useful for developing a product with the Telit HE910 module. This document is intended for Telit customers, who are integrators, about to implement their applications using our HE910 modules. For general contact, technical support, to report documentation errors and to order manuals, contact Telit’s Technical Support Center (TTSC) at: TS-EMEA@telit.com TS-NORTHAMERICA@telit.com TS-LATINAMERICA@telit.com TS-APAC@telit.com Alternatively, use: http://www.telit.com/en/products/technical-support-center/contact.php For detailed information about where you can buy the Telit modules or for recommendations on accessories and components visit: http://www.telit.com To register for product news and announcements or for product questions contact Telit’s Technical Support Center (TTSC). Our aim is to make this guide as helpful as possible. Keep us informed of your comments and suggestions for improvements. Telit appreciates feedback from the users of our information. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 7 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 This document contains the following chapters: Chapter 1: “Introduction” provides a scope for this document, target audience, contact and support information, and text conventions. Chapter 2: “Overview” provides an overview of the document. Chapter3: “HE910 Module Connections” deals with the pin out configuration and layout. Chapter 4: “Hardware Commands” How to operate on the module via hardware. Chapter 5: “Power supply” Power supply requirements and general design rules. Chapter 6: “GSM/WCDMA Radio” The antenna connection and board layout design are the most important parts in the full product design. Chapter 7: “GPS Receiver” This section describes the GPS receiver. Chapter 8: “Logic Level specifications” Specific values adopted in the implementation of logic levels for this module. Chapter 9: “USB Port” The USB port on the Telit HE910 is the core of the interface between the module and OEM hardware Chapter 10: “SPI port” Refers to the SPI port of the Telit HE910 Chapter 11: “Serial ports” Refers to the serial ports of the Telit HE910 Chapter 12: “Audio Section overview” Refers to the audio blocks of the Base Band Chip of the HE910 Telit Modules. Chapter 13: “General Purpose I/O” How the general purpose I/O pads can be configured. Chapter 14: “Mounting the HE910 on the application board” Mechanical dimensions and recommendations on how to mount the module on the user’s board. Chapter 15: “Safety Recommendations” Information related to the Safety topics. Chapter 16: “Conformity Assessment Issues” Information related to the Conformity Assessments. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 8 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Danger – This information MUST be followed or catastrophic equipment failure or bodily injury may occur. Caution or Warning – Alerts the user to important points about integrating the module, if these points are not followed, the module and end user equipment may fail or malfunction. Tip or Information – Provides advice and suggestions that may be useful when integrating the module. All dates are in ISO 8601 format, i.e. YYYY-MM-DD. HE910 Digital Voice Interface Application Note HE910 SPI Port Application Note HE910 Product description SIM Holder Design Guides AT Commands Reference Guide Telit EVK2 User Guide Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved 80000NT10050A 80000NT10053A 80378ST10085a 80000NT10001a 80378ST10091A 1vv0300704 page 9 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Revision ISSUE#0 ISSUE#1 ISSUE#2 ISSUE#3 ISSUE#4 ISSUE#5 ISSUE#6 Da t e 2011-03-31 2011-05-19 2011-05-25 2011-07-25 2011-07-29 2011-10-18 2011-12-22- ISSUE#7 ISSUE#8 ISSUE#9 ISSUE#10 2012-01-16 2012-02-03 2012-02-07 2012-03-16 ISSUE#11 ISSUE#12 ISSUE#13 ISSUE#14 2012-03-26 2012-03-27 2012-03-28 2012-05-08 ISSUE#15 ISSUE#16 ISSUE#17 ISSUE#18 2012-05-30 2012-06-06 2012-06-14 2012-06-15 Changes Preliminary Version Updated pinout on UART1 Update chapter 13 Added DVI app note references; chapter 4.1 Updated audio, on_off/reset and digital sections Added STAT_LED info, Updated SPI pinout Pads A8, A9, D14, A14 now reserved Power supply extended to 3.3 V par 4.3 renamed as “unconditional shutdown” USIF0 USIF1 names added to Main and AUX serial ports Updated IO logic levels Updated module’s mechanical drawing IO levels selection 1.8/1.2 removed (now only 1.8) Added HE910-GA and –D; added Conformity assessment chapter Chapter 5.1 updated Chapter 4.2 updated Added ADC in pinout description; added GPS specification; updated Chapter 13 and 14; Chapter 2.1, 2.1.2, 3.3, 5.4, 14.9 Added HE910-EU and NA products Updated paragraph 14.9 Added EUR, EUD, NAR, NAD variants; added Sensitivity and TX Power Class specifications. Updated par 14.7.1 and 14.3 Updated Chapter 16.2; 7.3.8 Pin R13 renamed as HW_SHUTDOWN*, Pin P11 adeed in pinout as RESET* Updated RTT&E info on HE910-NAG, NAR, NAD Updated RTT&E info on HE910-NAG, NAR, NAD ; updated par 3.1; Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 10 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The aim of this document is the description of some hardware solutions useful for developing a product with the Telit HE910 module. In this document all the basic functions of a mobile phone will be taken into account; for each one of them a proper hardware solution will be suggested and eventually the wrong solutions and common errors to be avoided will be evidenced. Obviously this document cannot embrace the whole hardware solutions and products that may be designed. The wrong solutions to be avoided shall be considered as mandatory, while the suggested hardware configurations shall not be considered mandatory, instead the information given shall be used as a guide and a starting point for properly developing your product with the Telit HE910 module. For further hardware details that may not be explained in this document refer to the Telit HE910 Product Description document where all the hardware information is reported. NOTICE: (EN) The integration of the GSM/GPRS/WCDMA HE910 cellular module within user application shall be done according to the design rules described in this manual. (IT) L’integrazione del modulo cellulare GSM/GPRS/WCDMA HE910 all’interno dell’applicazione dell’utente dovrà rispettare le indicazioni progettuali descritte in questo manuale. (DE) Die Integration des HE910 GSM/GPRS/WCDMA Mobilfunk-Moduls in ein Gerät muß gemäß der in diesem Dokument beschriebenen Kunstruktionsregeln erfolgen. (SL) Integracija GSM/GPRS/WCDMA HE910 modula v uporabniški aplikaciji bo morala upoštevati projektna navodila, opisana v tem priročniku. (SP) La utilización del modulo GSM/GPRS/WCDMA HE910 debe ser conforme a los usos para los cuales ha sido deseñado descritos en este manual del usuario. (FR) L’intégration du module cellulaire GSM/GPRS/WCDMA HE910 dans l’application de l’utilisateur sera faite selon les règles de conception décrites dans ce manuel. (HE) HE910 The information presented in this document is believed to be accurate and reliable. However, no responsibility is assumed by Telit Communications S.p.A. for its use, nor any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent rights of Telit Communications S.p.A. other than for circuitry embodied in Telit products. This document is subject to change without notice. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 11 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 PAD Signal I/O Function USB differential Data (+) Type COMMENT USB HS 2.0 COMMUNICATION PORT B15 USB_D+ I/O C15 USB_D- I/O USB differential Data (-) Power sense for the internal USB transceiver. VUSB A13 Asynchronous Serial Port (USIF0) - Prog. / Data + HW Flow Control N15 C103/TXD Serial data input from DTE CMOS 1.8V M15 C104/RXD Serial data output to DTE CMOS 1.8V M14 C108/DTR Input for (DTR) from DTE CMOS 1.8V Input for Request to send signal (RTS) from DTE Output for Clear to Send signal (CTS) to DTE L14 C105/RTS CMOS 1.8V P15 C106/CTS N14 C109/DCD Output for (DCD) to DTE CMOS 1.8V P14 C107/DSR Output for (DSR) to DTE CMOS 1.8V R14 C125/RING Output for Ring (RI) to DTE CMOS 1.8V CMOS 1.8V Asynchronous Auxiliary Serial Port (USIF1) D15 TX_AUX Auxiliary UART (TX Data to DTE) CMOS 1.8V E15 RX_AUX Auxiliary UART (RX Data from DTE) CMOS 1.8V D13 VDD_IO1 VDD_IO1 Input To be connected to E13 E13 1V8_SEL 1V8 SEL for VDD_IO1 To be connected to D13 SIM card interface A6 SIMCLK External SIM signal – Clock 1.8 / 3V A7 SIMRST External SIM signal – Reset 1.8 / 3V A5 SIMIO I/O External SIM signal – Data I/O 1.8 / 3V A4 SIMIN A3 SIMVCC External SIM signal – Presence (active low) External SIM signal – Power supply for the SIM CMOS 1.8 1.8 / 3V Digital Voice Interface (DVI) B9 DVI_WA0 I/O Digital Audio Interface (WA0) CMOS 1.8V B6 DVI_RX I/O Digital Audio Interface (RX) CMOS 1.8V B7 DVI_TX I/O Digital Audio Interface (TX) CMOS 1.8V B8 DVI_CLK I/O Digital Audio Interface (CLK) CMOS 1.8V SPI_MOSI SPI MOSI CMOS 1.8V Shared with TX_AUX Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 12 of 91 SPI D15 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 E15 SPI_MISO SPI_MISO CMOS 1.8V F15 SPI_CLK SPI Clock CMOS 1.8V H15 SPI_MRDY SPI_MRDY CMOS 1.8V J15 SPI_SRDY SPI_SRDY CMOS 1.8V C8 GPIO_01 I/O GPIO_01 /STAT LED CMOS 1.8V C9 GPIO_02 I/O GPIO_02 CMOS 1.8V C10 GPIO_03 I/O GPIO_03 CMOS 1.8V C11 GPIO_04 I/O GPIO_04 CMOS 1.8V B14 GPIO_05 I/O GPIO_05 CMOS 1.8V C12 GPIO_06 I/O GPIO_06 CMOS 1.8V Shared with RX_AUX DIGITAL IO C13 GPIO_07 I/O GPIO_07 CMOS 1.8V K15 GPIO_08 I/O GPIO_08 CMOS 1.8V L15 GPIO_09 I/O GPIO_09 CMOS 1.8V G15 GPIO_10 I/O GPIO_10 CMOS 1.8V ADC_IN1 AI Analog / Digital converter input A/D K1 ANTENNA I/O F1 ANT_DIV Alternate Function STAT LED ADC B1 Accepted values 0 to 1.2V DC RF SECTION GSM/EDGE/UMTS Antenna (50 ohm) Antenna Diversity Input (50 ohm) RF RF See NOTE 1 GPS SECTION (see NOTE1) ANT_GPS R9 GPS_LNA_EN R7 GPS Antenna (50 ohm) RF Output enable for External LNA supply CMOS 1.8V Miscellaneous Functions R13 HW_SHUTDOWN* HW Unconditional Shutdown CMOS 1.8V Active low P11 RESET* HW Unconditional Restart CMOS 1.8V Active low R12 ON_OFF* Input command for power ON CMOS 1.8V Active low C14 VRTC VRTC Backup capacitor Power backup for the embedded RTC supply R11 VAUX/PWRMON Supply Output for external accessories / Power ON Monitor 1.8V M1 VBATT Main power supply (Baseband) Power M2 VBATT Main power supply (Baseband) Power N1 VBATT_PA Main power supply (Radio PA) Power N2 VBATT_PA Main power supply (Radio PA) Power P1 VBATT_PA Main power supply (Radio PA) Power Power Supply P2 VBATT_PA Main power supply (Radio PA) Power E1 GND Ground Power G1 GND Ground Power Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 13 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 H1 GND Ground Power J1 GND Ground Power L1 GND Ground Power A2 GND Ground Power E2 GND Ground Power F2 GND Ground Power G2 GND Ground Power H2 GND Ground Power J2 GND Ground Power K2 GND Ground Power L2 GND Ground Power R2 GND Ground Power M3 GND Ground Power N3 GND Ground Power P3 GND Ground Power R3 GND Ground Power D4 GND Ground Power M4 GND Ground Power N4 GND Ground Power P4 GND Ground Power R4 GND Ground Power N5 GND Ground Power P5 GND Ground Power R5 GND Ground Power N6 GND Ground Power P6 GND Ground Power R6 GND Ground Power P8 GND Ground Power R8 GND Ground Power P9 GND Ground Power P10 GND Ground Power R10 GND Ground Power M12 GND Ground Power B13 GND Ground Power P13 GND Ground Power E14 GND Ground Power C1 RESERVED RESERVED D1 RESERVED RESERVED B2 RESERVED RESERVED C2 RESERVED RESERVED RESERVED Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 14 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 D2 RESERVED RESERVED B3 RESERVED RESERVED C3 RESERVED RESERVED D3 RESERVED RESERVED E3 RESERVED RESERVED F3 RESERVED RESERVED G3 RESERVED RESERVED H3 RESERVED RESERVED J3 RESERVED RESERVED K3 RESERVED RESERVED L3 RESERVED RESERVED B4 RESERVED RESERVED C4 RESERVED RESERVED B5 RESERVED RESERVED C5 RESERVED RESERVED C6 RESERVED RESERVED C7 RESERVED RESERVED N7 RESERVED RESERVED P7 RESERVED RESERVED N8 RESERVED RESERVED N9 RESERVED RESERVED A10 RESERVED RESERVED N10 RESERVED RESERVED N11 RESERVED RESERVED P11 RESERVED RESERVED B12 RESERVED RESERVED D12 RESERVED RESERVED N12 RESERVED RESERVED P12 RESERVED RESERVED F14 RESERVED RESERVED G14 RESERVED RESERVED H14 RESERVED RESERVED J14 RESERVED RESERVED K14 RESERVED RESERVED N13 RESERVED RESERVED L13 RESERVED RESERVED J13 RESERVED RESERVED M13 RESERVED RESERVED K13 RESERVED RESERVED H13 RESERVED RESERVED G13 RESERVED RESERVED F13 RESERVED RESERVED Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 15 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 A11 RESERVED RESERVED A12 RESERVED RESERVED B11 RESERVED RESERVED B10 RESERVED RESERVED A9 RESERVED RESERVED A8 RESERVED RESERVED D14 RESERVED RESERVED A14 RESERVED RESERVED WARNING: Reserved pins must not be connected. NOTE 1: The following table is listing the main Pinout differences between the HE910 variants Product GPS HE910 HE910-D HE910-GA HE910-EUR HE910-EUD HE910-EUG HE910-NAR HE910-NAD HE910-NAG YES NO YES NO NO YES NO NO YES Antenna Diversity YES YES YES NO NO NO NO NO NO Notes Reserved Pads: R7, R9 Reserved Pads:,F1, R7, R9 Reserved Pads:,F1, R7, R9 Reserved Pads: F1 Reserved Pads: F1, R7, R9 Reserved Pads: F1, R7, R9 Reserved Pads: F1 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 16 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 If not used, almost all pins should be left disconnected. The only exceptions are the following pins: PAD M1,M2,N1,N2,P1,P2 E1,G1,H1,J1,L1,A2,E2,F2,G2,H2, J2,K2,L2,R2,M3,N3,P3,R3,D4,M4, N4,P4,R4,N5,P5,R5,N6,P6,R6,P8, R8,P9,P10,R10,M12,B13,P13,E14 R12 R13 B15 C15 A13 N15 M15 L14 P15 D15 E15 D13 E13 K1 F1 R9 signal VBATT & VBATT_PA GND ON/OFF* HW_SHUTDOWN* USB_D+ USB_DVUSB C103/TXD C104/RXD C105/RTS C106/CTS TXD_AUX RXD_AUX VDD_IO1 1V8_SEL MAIN ANTENNA ANT_DIV (if supported by the product) ANT_GPS (if supported by the product) RTS pin should be connected to the GND (on the module side) if flow control is not used. The above pins are also necessary to debug the application when the module is assembled on it. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 17 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 ADC_IN1 RES RES GND ANT_DIV GND GND GND ANT GND VBATT VBATT_ PA VBATT_ PA GND RES RES RES GND GND GND GND GND GND GND VBATT VBATT_ PA VBATT_ PA GND SIMVC RES RES RES RES RES RES RES RES RES RES GND GND GND GND SIMIN RES RES GND GND GND GND GND SIMIO RES RES GND GND GND SIMCLK DVI_RX RES GND GND GND SIMRS DVI_TX RES RES RES GPS_LN A_EN RES DVI_CLK GPIO_01 RES GND GND RES DVI_WA GPIO_02 RES GND ANT_GP 10 RES RES GPIO_03 RES GND GND 11 RES RES GPIO_04 RES RESET* VAUX/P WRMON 12 RES RES GPIO_06 RES GND RES RES ON_OFF 13 VUSB GND GPIO_07 VDD_IO 1V8_SEL RES RES RES RES RES RES RES RES GND HW_SH UTDOW N* 14 RES GPIO_05 VRTC RES GND RES RES RES RES RES C105/RT C108/DT C109/DC C107/DS C125/RI NG USB_D+ USB_D- TX AUX RX AUX SPI_CLK GPIO_10 SPI_MR DY SPI_SR DY GPIO_08 GPIO_09 C104/RX C103/TX C106/CT 15 NOTE: The pin defined as RES has to be considered RESERVED and not connected on any pin in the application. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 18 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 ADC_IN1 RES RES GND ANT_DIV GND GND GND ANT GND VBATT VBATT_ PA VBATT_ PA GND RES RES RES GND GND GND GND GND GND GND VBATT VBATT_ PA VBATT_ PA GND SIMVC RES RES RES RES RES RES RES RES RES RES GND GND GND GND SIMIN RES RES GND GND GND GND GND SIMIO RES RES GND GND GND SIMCLK DVI_RX RES GND GND GND SIMRS DVI_TX RES RES RES RES RES DVI_CLK GPIO_01 RES GND GND RES DVI_WA GPIO_02 RES GND RES 10 RES RES GPIO_03 RES GND GND 11 RES RES GPIO_04 RES RESET* VAUX/P WRMON 12 RES RES GPIO_06 RES GND RES RES ON_OFF 13 VUSB GND GPIO_07 VDD_IO 1V8_SEL RES RES RES RES RES RES RES RES GND HW_SH UTDOW N* 14 RES GPIO_05 VRTC RES GND RES RES RES RES RES C105/RT C108/DT C109/DC C107/DS C125/RI NG USB_D+ USB_D- TX AUX RX AUX SPI_CLK GPIO_10 SPI_MR DY SPI_SR DY GPIO_08 GPIO_09 C104/RX C103/TX C106/CT 15 NOTE: The pin defined as RES has to be considered RESERVED and not connected on any pin in the application. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 19 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 ADC_IN1 RES RES GND RES GND GND GND ANT GND VBATT VBATT_ PA VBATT_ PA GND RES RES RES GND GND GND GND GND GND GND VBATT VBATT_ PA VBATT_ PA GND SIMVC RES RES RES RES RES RES RES RES RES RES GND GND GND GND SIMIN RES RES GND GND GND GND GND SIMIO RES RES GND GND GND SIMCLK DVI_RX RES GND GND GND SIMRS DVI_TX RES RES RES RES RES DVI_CLK GPIO_01 RES GND GND RES DVI_WA GPIO_02 RES GND RES 10 RES RES GPIO_03 RES GND GND 11 RES RES GPIO_04 RES RESET* VAUX/P WRMON 12 RES RES GPIO_06 RES GND RES RES ON_OFF 13 VUSB GND GPIO_07 VDD_IO 1V8_SEL RES RES RES RES RES RES RES RES GND HW_SH UTDOW N* 14 RES GPIO_05 VRTC RES GND RES RES RES RES RES C105/RT C108/DT C109/DC C107/DS C125/RI NG USB_D+ USB_D- TX AUX RX AUX SPI_CLK GPIO_10 SPI_MR DY SPI_SR DY GPIO_08 GPIO_09 C104/RX C103/TX C106/CT 15 NOTE: The pin defined as RES has to be considered RESERVED and not connected on any pin in the application. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 20 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 ADC_IN1 RES RES GND RES GND GND GND ANT GND VBATT VBATT_ PA VBATT_ PA GND RES RES RES GND GND GND GND GND GND GND VBATT VBATT_ PA VBATT_ PA GND SIMVC RES RES RES RES RES RES RES RES RES RES GND GND GND GND SIMIN RES RES GND GND GND GND GND SIMIO RES RES GND GND GND SIMCLK DVI_RX RES GND GND GND SIMRS DVI_TX RES RES RES GPS_LN A_EN RES DVI_CLK GPIO_01 RES GND GND RES DVI_WA GPIO_02 RES GND ANT_GP 10 RES RES GPIO_03 RES GND GND 11 RES RES GPIO_04 RES RESET* VAUX/P WRMON 12 RES RES GPIO_06 RES GND RES RES ON_OFF 13 VUSB GND GPIO_07 VDD_IO 1V8_SEL RES RES RES RES RES RES RES RES GND HW_SH UTDOW N* 14 RES GPIO_05 VRTC RES GND RES RES RES RES RES C105/RT C108/DT C109/DC C107/DS C125/RI NG USB_D+ USB_D- TX AUX RX AUX SPI_CLK GPIO_10 SPI_MR DY SPI_SR DY GPIO_08 GPIO_09 C104/RX C103/TX C106/CT 15 NOTE: The pin defined as RES has to be considered RESERVED and not connected on any pin in the application. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 21 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 To turn on the HE910 the pad ON_OFF* must be tied low for at least 5 seconds and then released. The maximum current that can be drained from the ON# pad is 0,1 mA. A simple circuit to do it is: NOTE: Don't use any pull up resistor on the ON_OFF* line, it is internally pulled up. Using pull up resistor may bring to latch up problems on the HE910 power regulator and improper power on/off of the module. The line ON_OFF* must be connected only in open collector or open drain configuration. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 22 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 NOTE: In this document all the lines that are inverted, hence have active low signals are labelled with a name that ends with”#",”*” or with a bar over the name. TIP: To check if the device has powered on, the hardware line PWRMON should be monitored. NOTE: It is mandatory to avoid sending data to the serial ports during the first 200ms of the module start-up. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 23 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 A flow chart showing the proper turn on procedure is displayed below: Modem ON Proc. PWMON = ON? DELAY= 300mSec Enter ATON_OFF = LOW Delay = 5 Sec AT answer in 1Sec ? ON_OFF = HIGH PWMON = ON? AT init sequence. HW unconditional SHUTDOWN Delay 1s Start AT CMD. NOTE: In order to avoid a back powering effect it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the HE910 when the module is powered off or during an ON/OFF transition. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 24 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 A flow chart showing the AT command managing procedure is displayed below: Start AT CMD. DELAY= 300mSec Enter AT AT answer in 1Sec ? AT init sequence. HW unconditional SHUTDOWN Modem ON Proc. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 25 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 For example: 1- Let's assume you need to drive the ON# pad with a totem pole output of a +3/5 V microcontroller (uP_OUT1): 2- Let's assume you need to drive the ON# pad directly with an ON/OFF button: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 26 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Turning off of the device can be done in two ways: via AT command (see HE910 Software User Guide, AT#SHDN) by tying low pin ON_OFF* Either ways, the device issues a detach request to network informing that the device will not be reachable any more. To turn OFF the HE910 the pad ON_OFF* must be tied low for at least 2 seconds and then released. TIP: To check if the device has been powered off, the hardware line PWRMON must be monitored. The device is powered off when PWRMON goes low. NOTE: In order to avoid a back powering effect it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the HE910 when the module is powered off or during an ON/OFF transition. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 27 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The following flow chart shows the proper turn off procedure: Modem OFF Proc. PWMON = ON? ON_OFF = LOW Delay = 2 Sec ON_OFF = HIGH Modem ON Proc. PWMON = ON? Delay 15s PWMON = ON? HW unconditional SHUTDOWN Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 28 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The Unconditional Shutdown of the module could be activated using the HW_SHUTDOWN* line (pad R13). WARNING: The hardware unconditional Shutdown must not be used during normal operation of the device since it does not detach the device from the network. It shall be kept as an emergency exit procedure. To unconditionally shutdown the HE910, the pad HW_SHUTDOWN* must be tied low for at least 200 milliseconds and then released. NOTE: Do not use any pull up resistor on the HW_SHUTDOWN* line nor any totem pole digital output. Using pull up resistor may bring to latch up problems on the HE910 power regulator and improper functioning of the module. The line HW_SHUTDOWN* must be connected only in open collector configuration. The HW_SHUTDOWN* is generating an unconditional shutdown of the module without an automatic restart. The module will shutdown, but will NOT perform the detach from the cellular network. To proper power on again the module please refer to the related paragraph (“Powering ON the HE910”) TIP: The unconditional hardware shutdown must always be implemented on the boards and should be used only as an emergency exit procedure. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 29 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 A typical circuit is the following: For example: 1- Let us assume you need to drive the HW_SHUTDOWN* pad with a totem pole output of a +3/5 V microcontroller (uP_OUT2): NOTE: In order to avoid a back powering effect it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the HE910 when the module is powered off or during an ON/OFF transition. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 30 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 In the following flow chart is detailed the proper restart procedure: HW unconditional SHUTDOWN HW_SHUTDOWN*= LOW = LOW Delay 200ms HW_SHUTDOWN*= HIGH PWRMON = ON Modem ON Proc. Delay 1s Disconnect PWR supply Modem ON Proc. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 31 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The Unconditional Restart of the module could be activated using the RESET* line (pad P11). WARNING: The hardware unconditional Restart must not be used during normal operation of the device since it does not detach the device from the network. It shall be kept as an emergency exit procedure. To unconditionally Restart the HE910, the pad RESET* must be tied low for at least 200 milliseconds and then released. NOTE: Do not use any pull up resistor on the RESET* line nor any totem pole digital output. Using pull up resistor may bring to latch up problems on the HE910 power regulator and improper functioning of the module. The line RESET* must be connected only in open collector configuration. The module will Restart and will NOT perform the detach from the cellular network. TIP: The unconditional hardware Restart should be implemented on the boards and should be used only as an emergency exit procedure. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 32 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 A typical circuit is the following: For example: 1- Let us assume you need to drive the RESET* pad with a totem pole output of a +3/5 V microcontroller (uP_OUT2): NOTE: In order to avoid a back powering effect it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the HE910 when the module is powered off or during an ON/OFF transition. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 33 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 In the following flow chart is detailed the proper restart procedure: HW unconditional Restart Reset* = LOW Delay 200ms Reset* = HIGH PWRMON = ON Modem Startup Delay 1s Disconnect PWR supply Modem ON Proc. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 34 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The power supply circuitry and board layout are a very important part in the full product design and they strongly reflect on the product overall performances, hence read carefully the requirements and the guidelines that will follow for a proper design. The external power supply must be connected to VBATT & VBATT_PA signals and must fulfil the following requirements: POWER SUPPLY Nominal Supply Voltage Normal Operating Voltage Range Extended Operating Voltage Range 3.8 V 3.40 V÷ 4.20 V 3.10 V÷ 4.50 V NOTE: The Operating Voltage Range MUST never be exceeded; care must be taken when designing the application’s power supply section to avoid having an excessive voltage drop. If the voltage drop is exceeding the limits it could cause a Power Off of the module. NOTE: Overshoot voltage (regarding MAX Extended Operating Voltage) and drop in voltage (regarding MIN Extended Operating Voltage) MUST never be exceeded; The “Extended Operating Voltage Range” can be used only with completely assumption and application of the HW User guide suggestions. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 35 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 HE910 Mode SWITCHED OFF Switched Off AT+CFUN=5 AT+CFUN=1 AT+CFUN=4 AT+CFUN=5 WCDMA Voice WCDMA HSDPA (0dBm) WCDMA HSDPA (22dBm) EDGE 4TX+2RX GSM900 PL5 DCS1800 PL0 Average (mA) 40uA Mode description Module supplied but Switched Off IDLE mode (WCDMA) Disabled TX and RX; DRX7 IDLE mode (GSM/EDGE) 19 Normal mode: full functionality of the module 16.5 Disabled TX and RX; module is not registered on the network 0.8 Disabled TX and RX; DRX9 (1.1mA in case of DRX5) Operative mode (WCDMA) 152 WCDMA voice call (TX = 10dBm) 187 WCDMA data call (Cat 14, TX = 0dBm) 494 WCDMA data call (Cat 14, TX = 22dBm) Operative mode (EDGE) 1.2 495 484 EDGE Sending data mode Operative mode (GSM) CSD TX and RX mode GSM900 CSD PL5 DCS1800 CSD PL0 GPRS 4TX+2RX GSM900 PL5 DCS1800 PL0 220 167 GSM VOICE CALL 580 438 GPRS Sending data mode The GSM system is made in a way that the RF transmission is not continuous, else it is packed into bursts at a base frequency of about 216 Hz, and the relative current peaks can be as high as about 2A. Therefore the power supply has to be designed in order to withstand with these current peaks without big voltage drops; this means that both the electrical design and the board layout must be designed for this current flow. If the layout of the PCB is not well designed a strong noise floor is generated on the ground and the supply; this will reflect on all the audio paths producing an audible annoying noise at 216 Hz; if the voltage drop during the peak current absorption is too much, then the device may even shutdown as a consequence of the supply voltage drop. NOTE: The electrical design for the Power supply should be made ensuring it will be capable of a peak current output of at least 2 A. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 36 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The principal guidelines for the Power Supply Design embrace three different design steps: the electrical design the thermal design the PCB layout. The electrical design of the power supply depends strongly from the power source where this power is drained. We will distinguish them into three categories: +5V input (typically PC internal regulator output) +12V input (typically automotive) Battery The desired output for the power supply is 3.8V, hence there's not a big difference between the input source and the desired output and a linear regulator can be used. A switching power supply will not be suited because of the low drop out requirements. When using a linear regulator, a proper heat sink shall be provided in order to dissipate the power generated. A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current absorption peaks close to the HE910, a 100μF tantalum capacitor is usually suited. Make sure the low ESR capacitor on the power supply output (usually a tantalum one) is rated at least 10V. A protection diode should be inserted close to the power input, in order to save the HE910 from power polarity inversion. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 37 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 An example of linear regulator with 5V input is: The desired output for the power supply is 3.8V, hence due to the big difference between the input source and the desired output, a linear regulator is not suited and shall not be used. A switching power supply will be preferable because of its better efficiency especially with the 2A peak current load represented by the HE910. When using a switching regulator, a 500kHz or more switching frequency regulator is preferable because of its smaller inductor size and its faster transient response. This allows the regulator to respond quickly to the current peaks absorption. In any case the frequency and Switching design selection is related to the application to be developed due to the fact the switching frequency could also generate EMC interferences. For car PB battery the input voltage can rise up to 15,8V and this should be kept in mind when choosing components: all components in the power supply must withstand this voltage. A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current absorption peaks, a 100μF tantalum capacitor is usually suited. Make sure the low ESR capacitor on the power supply output (usually a tantalum one) is rated at least 10V. For Car applications a spike protection diode should be inserted close to the power input, in order to clean the supply from spikes. A protection diode should be inserted close to the power input, in order to save the HE910 from power polarity inversion. This can be the same diode as for spike protection. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 38 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 An example of switching regulator with 12V input is in the below schematic: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 39 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The desired nominal output for the power supply is 3.8V and the maximum voltage allowed is 4.2V, hence a single 3.7V Li-Ion cell battery type is suited for supplying the power to the Telit HE910 module. WARNING: The three cells Ni/Cd or Ni/MH 3,6 V Nom. battery types or 4V PB types MUST NOT BE USED DIRECTLY since their maximum voltage can rise over the absolute maximum voltage for the HE910 and damage it. NOTE: DON'T USE any Ni-Cd, Ni-MH, and Pb battery types directly connected with HE910. Their use can lead to overvoltage on the HE910 and damage it. USE ONLY Li-Ion battery types. A Bypass low ESR capacitor of adequate capacity must be provided in order to cut the current absorption peaks, a 100μF tantalum capacitor is usually suited. Make sure the low ESR capacitor (usually a tantalum one) is rated at least 10V. A protection diode should be inserted close to the power input, in order to save the HE910 from power polarity inversion. Otherwise the battery connector should be done in a way to avoid polarity inversions when connecting the battery. The battery capacity must be at least 500mAh in order to withstand the current peaks of 2A; the suggested capacity is from 500mAh to 1000mAh. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 40 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The thermal design for the power supply heat sink should be done with the following specifications: Average current consumption during HSDPA transmission @PWR level max : 600 mA Average current during idle: 1.5 mA NOTE: The average consumption during transmissions depends on the power level at which the device is requested to transmit by the network. The average current consumption hence varies significantly. Considering the very low current during idle, especially if Power Saving function is enabled, it is possible to consider from the thermal point of view that the device absorbs current significantly only during calls. If we assume that the device stays into transmission for short periods of time (let's say few minutes) and then remains for a quite long time in idle (let's say one hour), then the power supply has always the time to cool down between the calls and the heat sink could be smaller than the calculated one for 600mA maximum RMS current, or even could be the simple chip package (no heat sink). Moreover in the average network conditions the device is requested to transmit at a lower power level than the maximum and hence the current consumption will be less than the 600mA, being usually around 150mA. For these reasons the thermal design is rarely a concern and the simple ground plane where the power supply chip is placed can be enough to ensure a good thermal condition and avoid overheating. For the heat generated by the HE910, you can consider it to be during transmission 1W max during CSD/VOICE calls and 2W max during class10 GPRS upload. This generated heat will be mostly conducted to the ground plane under the HE910; you must ensure that your application can dissipate it. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 41 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 As seen on the electrical design guidelines the power supply shall have a low ESR capacitor on the output to cut the current peaks and a protection diode on the input to protect the supply from spikes and polarity inversion. The placement of these components is crucial for the correct working of the circuitry. A misplaced component can be useless or can even decrease the power supply performances. The Bypass low ESR capacitor must be placed close to the Telit HE910 power input pads or in the case the power supply is a switching type it can be placed close to the inductor to cut the ripple provided the PCB trace from the capacitor to the HE910 is wide enough to ensure a dropless connection even during the 2A current peaks. The protection diode must be placed close to the input connector where the power source is drained. The PCB traces from the input connector to the power regulator IC must be wide enough to ensure no voltage drops occur when the 2A current peaks are absorbed. Note that this is not made in order to save power loss but especially to avoid the voltage drops on the power line at the current peaks frequency of 216 Hz that will reflect on all the components connected to that supply, introducing the noise floor at the burst base frequency. For this reason while a voltage drop of 300-400 mV may be acceptable from the power loss point of view, the same voltage drop may not be acceptable from the noise point of view. If your application doesn't have audio interface but only uses the data feature of the Telit HE910, then this noise is not so disturbing and power supply layout design can be more forgiving. The PCB traces to the HE910 and the Bypass capacitor must be wide enough to ensure no significant voltage drops occur when the 2A current peaks are absorbed. This is for the same reason as previous point. Try to keep this trace as short as possible. The PCB traces connecting the Switching output to the inductor and the switching diode must be kept as short as possible by placing the inductor and the diode very close to the power switching IC (only for switching power supply). This is done in order to reduce the radiated field (noise) at the switching frequency (100-500 kHz usually). The use of a good common ground plane is suggested. The placement of the power supply on the board should be done in such a way to guarantee that the high current return paths in the ground plane are not overlapped to any noise sensitive circuitry as the microphone amplifier/buffer or earphone amplifier. The power supply input cables should be kept separate from noise sensitive lines such as microphone/earphone cables. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 42 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The following table is listing the main differences between the HE910 variants: Product HE910 HE910-D HE910-GA HE910-EUR HE910-EUD HE910-EUG HE910-NAR HE910-NAD HE910-NAG Supported 2G Bands GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 Supported 3G bands FDD B1, B2, B4, B5, B8 FDD B1, B2, B4, B5, B8 Band GSM 850 / 900 DCS1800 / PCS 1900 EDGE, 850/900 MHz EDGE, 1800/1900 MHz WCDMA FDD B1, B2, B4, B5, B8 FDD B1, B2, B5, B8 Antenna Diversity FDD B1, B2, B5, B8 GSM 850, GSM 900, PCS 1900 FDD B1, B2, B5, B8 GSM 850, GSM 900, PCS 1900 FDD B1, B2, B5, B8 GSM 850, GSM 900, PCS 1900 FDD B1, B5, B8 NO FDD B1, B5, B8 NO FDD B1, B5, B8 NO FDD B2, B4, B5 NO FDD B2, B4, B5 NO FDD B2, B4, B5 NO Power Class 4 (2W) 1 (1W) E2 (0.5W) Class E2 (0.4W) Class 3 (0.25W) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 43 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Band GSM 850 GSM 900 DCS1800 PCS 1900 WCDMA FDD B1 WCDMA FDD B2 WCDMA FDD B4 WCDMA FDD B5 WCDMA FDD B8 Typical -109.5 dBm -109 dBm -110 dBm -109.5 dBm -111 dBm -110 dBm -111 dBm -111 dBm -110 dBm Note BER Class II <2.44% BER Class II <2.44% BER Class II <2.44% BER Class II <2.44% BER <0.01% BER <0.01% BER <0.01% BER <0.01% BER <0.01% The antenna connection and board layout design are the most important aspect in the full product design as they strongly affect the product overall performances, hence read carefully and follow the requirements and the guidelines for a proper design. The antenna and antenna transmission line on PCB for a Telit HE910 device shall fulfil the following requirements: Frequency range Bandwidth (GSM/EDGE) Bandwidth (WCDMA) Impedance Input power VSWR absolute max VSWR recommended ANTENNA REQUIREMENTS Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for that/those band(s) 70 MHz in GSM850, 80 MHz in GSM900, 170 MHz in DCS & 140 MHz PCS band 70 MHz in WCDMA Band V 80 MHz in WCDMA Band VIII 460 MHz in WCDMA Band IV 140 MHz in WCDMA Band II 250 MHz in WCDMA Band I 50 ohm > 33dBm(2 W) peak power in GSM > 24dBm Average power in WCDMA ≤ 5:1 (limit to avoid permanent damage) ≤ 2:1 (limit to fulfil all regulatory requirements) When using the HE910, since there's no antenna connector on the module, the antenna must be connected to the HE910 antenna pad (K1) by means of a transmission line implemented on the PCB. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 44 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 In the case the antenna is not directly connected at the antenna pad of the HE910, then a PCB line is needed in order to connect with it or with its connector. This transmission line shall fulfil the following requirements: ANTENNA LINE ON PCB REQUIREMENTS Characteristic Impedance 50 ohm Max Attenuation 0,3 dB Coupling with other signals shall be avoided Cold End (Ground Plane) of antenna shall be equipotential to the HE910 ground pins Furthermore if the device is developed for the US market and/or Canada market, it shall comply with the FCC and/or IC approval requirements: This device is to be used only for mobile and fixed application. In order to re-use the Telit FCC/IC approvals the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. If antenna is installed with a separation distance of less than 20 cm from all persons or is co-located or operating in conjunction with any other antenna or transmitter then additional FCC/IC testing may be required. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. Antennas used for this OEM module must not exceed the gains for mobile and fixed operating configurations as described in “FCC/IC Regulatory notices” chapter. Make sure that the transmission line’s characteristic impedance is 50ohm ; Keep line on the PCB as short as possible, since the antenna line loss shall be less than around 0,3 dB; Line geometry should have uniform characteristics, constant cross section, avoid meanders and abrupt curves; Any kind of suitable geometry / structure (Microstrip, Stripline, Coplanar, Grounded Coplanar Waveguide...) can be used for implementing the printed transmission line afferent the antenna; If a Ground plane is required in line geometry, that plane has to be continuous and sufficiently extended, so the geometry can be as similar as possible to the related canonical model; Keep, if possible, at least one layer of the PCB used only for the Ground plane; If possible, use this layer as reference Ground plane for the transmission line; It is wise to surround (on both sides) the PCB transmission line with Ground, avoid having other signal tracks facing directly the antenna line track. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 45 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Avoid crossing any un-shielded transmission line footprint with other signal tracks on different layers; The ground surrounding the antenna line on PCB has to be strictly connected to the main Ground Plane by means of via holes (once per 2mm at least), placed close to the ground edges facing line track; Place EM noisy devices as far as possible from HE910 antenna line; Keep the antenna line far away from the HE910 power supply lines; If EM noisy devices are present on the PCB hosting the HE910, such as fast switching ICs, take care of the shielding of the antenna line by burying it inside the layers of PCB and surround it with Ground planes, or shield it with a metal frame cover. If EM noisy devices are not present around the line, the use of geometries like Microstrip or Grounded Coplanar Waveguide has to be preferred, since they typically ensure less attenuation if compared to a Stripline having same length; Install the antenna in a place covered by the GSM signal. If the device antenna is located greater then 20cm from the human body and there are no colocated transmitter then the Telit FCC/IC approvals can be re-used by the end product If the device antenna is located less then 20cm from the human body or there are no colocated transmitter then the additional FCC/IC testing may be required for the end product (Telit FCC/IC approvals cannot be reused) Antenna shall not be installed inside metal cases Antenna shall be installed also according Antenna manufacturer instructions. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 46 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 This product is including an input for a second RX antenna to improve the radio sensitivity. The function is called Antenna Diversity. Frequency range Bandwidth (GSM/EDGE) Bandwidth (WCDMA) Impedance ANTENNA REQUIREMENTS Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for that/those band(s) 70 MHz in GSM850, 80 MHz in GSM900 & 140 MHz PCS band 70 MHz in WCDMA Band V 80 MHz in WCDMA Band VIII 140 MHz in WCDMA Band II 250 MHz in WCDMA Band I 50 ohm When using the HE910, since there's no antenna connector on the module, the antenna must be connected to the HE910 antenna pad (F1) by means of a transmission line implemented on the PCB. In the case the antenna is not directly connected at the antenna pad of the HE910, then a PCB line is needed in order to connect with it or with its connector. The second Rx antenna should not be located in the close vicinity of main antenna. In order to improve Diversity Gain, Isolation and reduce mutual interaction, the two antennas should be located at the maximum reciprocal distance possible, taking into consideration the available space into the application. NOTE1: The Diversity is not supported on DCS 1800 in 2G and FDD BAND IV in 3G NOTE: If the RX Diversity is not used/connected, disable the Diversity functionality using the AT#RXDIV command (ref to the AT User guide for the proper syntax) and leave the pad F1 unconnected. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 47 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 module is integrating a GPS receiver that could be used in Standalone mode and in A-GPS (assisted GPS). With the help of advanced digital signal processing algorithms and the use of A-GPS data, the receiver is capable to achieve sensitivity values of better than -165 dBm as is required for indoor applications. The following table is listing the HE910 variants that support the GPS receiver: Product HE910 HE910-D HE910-GA HE910-EUR HE910-EUD HE910-EUG HE910-NAR HE910-NAD HE910-NAG GPS Receiver YES NO YES NO NO YES NO NO YES Advanced real time hardware correlation engine for enhanced sensitivity (better than -165 dBm for A-GPS). Fast Acquisition giving rapid Time-to-First-Fix (TTFF) Capability to monitor up to 28 channels Stand Alone and Assisted mode Integrated LNA The following Table is listing the main characteristics: Characteristic GPS RX Sensitivity GPS Cold Start Autonomous GPS Hot Start Autonomous GPS tracking mode GPS Accuracy TTFF from Cold Start TTF from Warm Start TTF from Hot Start Power Consumption in Acquisition Power Consumption in Tracking Power Consumption in Low Power Tracking Typical Values -164dBm -147dBm -161dBm -166 dBm 3m 42 sec 30sec 1.8 sec 46.4 mA @3.8V 37.8 mA @3.8V 25.7 mA @3.8V Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 48 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The Pads related to this function are the following: PAD Signal I/O Function Type R9 ANT_GPS GPS Antenna (50 ohm) RF R7 GPS_LNA_EN Output enable for External LNA supply CMOS 1.8V The HE910 Module contains an integrated LNA and pre-select SAW filter. This allows the module to work well with a passive GPS antenna. If the antenna cannot be located near the HE910, then an active antenna (that is, an antenna with a low noise amplifier built in) can be used. The HE910 can achieve Cold Start acquisition with a signal level of -147 dBm at its input. This means the GPS receiver can find the necessary satellites, download the necessary ephemeris data and compute the location within a 5 minute period. In the GPS signal acquisition process, downloading and decoding the data is the most difficult task, which is why Cold Start acquisition requires a higher signal level than navigation or tracking signal levels. For the purposes of this discussion, autonomous operation is assumed, which makes the Cold Start acquisition level the important design constraint. If assistance data in the form of time or ephemeris aiding is available, then even lower signal levels can be used to compute a navigation solution. Each GPS satellite presents its own signal to the HE910, and best performance is obtained when the signal levels are between -125 dBm and -117 dBm. These received signal levels are determined by : GPS satellite transmit power GPS satellite elevation and azimuth Free space path loss Extraneous path loss such as rain Partial or total path blockage such as foliage or building Multipath caused by signal reflection GPS antenna Signal path after the GPS antenna The first three items in the list above are specified in IS-GPS-200E, readily available multiple sources online. IS-GPS-200E specifies a signal level minimum of -130 dBm will be presented to the receiver when using a linearly polarized antenna with 3 dBi gain. The GPS signal is relatively immune to rainfall attenuation and does not really need to be considered. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 49 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 However, the GPS signal is heavily influenced by attenuation due to foliage such as tree canopies, etc., as well as outright blockage caused by building, terrain or other items in the line of sight to the specific GPS satellite. This variable attenuation is highly dependent upon GPS satellite location. If enough satellites are blocked, say at a lower elevation, or all in a general direction, the geometry of the remaining satellites will result is a lower accuracy of position. The HE910 reports this geometry in the form of PDOP, HDOP and VDOP. For example, in a vehicular application, the GPS antenna may be placed embedded into the dashboard or rear package tray of an automobile. The metal roof of the vehicle will cause significant blockage, plus any thermal coating applied to the vehicle glass can attenuate the GPS signal by as much as 15 dB. Again, both of these factors will affect the performance of the receiver. Multipath is a phenomena where the signal from a particular satellite is reflected and is received by the GPS antenna in addition to or in place of the original line of sight signal. The multipath signal has a path length that is longer than the original line of sight path and can either attenuate the original signal, or if received in place of the original signal add additional error in determining a solution because the distance to the particular GPS satellite is actually longer than expected. It is this phenomena that makes GPS navigation in urban canyons (narrow roads surround by high rise buildings) so challenging. In general, the reflecting of the GPS signal causes the polarization to reverse. The implications of this are covered in the next section. The GPS signal as broadcast is a right hand circularly polarized signal. The best antenna to receive the GPS signal is a right hand circularly (RHCP) polarized antenna. Remember that IS-GPS-200E specifies the receive power level with a linearly polarized antenna. A linearly polarized antenna will have 3 dB loss as compared to an RHCP antenna assuming the same antenna gain (specified in dBi and dBic respectively). An RHCP antenna is better at rejecting multipath than a linearly polarized antenna. This is because the reflected signal changes polarization to LHCP, which would be rejected by the RHCP antenna by typically 20 dB or so. If the multipath signal is attenuating the line of sight signal, then the RHCP antenna would show a higher signal level than a linearly polarized antenna because the interfering signal is rejected. However, in the case where the multipath signal is replacing the line of sight signal, such as in an urban canyon environment, then the number of satellites in view could drop below that needed to determine a 3D solution. This is a case where a bad signal may be better than no signal. The system designer needs to make tradeoffs in their application to determine which is the better choice. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 50 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Antenna gain is defined as the extra signal power from the antenna as compared to a theoretical isotropic antenna (equally sensitive in all directions). For example, a 25mm by 25m square patch antenna on a reference ground plane (usually 70mm by 70mm) will give an antenna gain at zenith of 5 dBic. A smaller 18mm by 18mm square patch on a reference ground plane (usually 50mm by 50mm) will give an antenna gain at zenith of 2 dBic. While an antenna vendor will specify a nominal antenna gain (usually at zenith, or directly overhead) they should supply antenna pattern curves specifying gain as a function of elevation, and gain at a fixed elevation as a function of azimuth. Pay careful attention to the requirement to meet these specifications, such as ground plane required and any external matching components. Failure to follow these requirements could result in very poor antenna performance. It is important to note that GPS antenna gain is not the same thing as external LNA gain. Most antenna vendors will specify these numbers separately, but some combine them into a single number. It is important to know both numbers when designing and evaluating the front end of a GPS receiver. For example, antenna X has an antenna gain of 5 dBiC at azimuth and an LNA gain of 20 dB for a combined total of 25 dB. Antenna Y has an antenna gain of -5 dBiC at azimuth and an LNA gain of 30 dB for a combined total of 25 dB. However, in the system, antenna X will outperform antenna Y by about 10 dB (refer to next chapter for more details on system noise floor). An antenna with higher gain will generally outperform an antenna with lower gain. Once the signals are above about -130 dBm for a particular satellite, no improvement in performance would be gained. However, for those satellites that are below about -125 dBm, a higher gain antenna would improve the gain and improve the performance of the GPS receiver. In the case of really weak signals, a good antenna could mean the difference between being able to use a particular satellite signal or not. If the GPS antenna is placed near the HE910 and the RF traces losses are not excessive (nominally 1 dB), then a passive antenna can be used. This would normally be the lowest cost option and most of the time the simplest to use. However, if the antenna needs to be located away from the HE910 then an active antenna may be required to obtain the best system performance. The active antenna has its own built in low noise amplifier to overcome RF trace or cable losses after the active antenna. However, an active antenna has a low noise amplifier (LNA) with associated gain and noise figure. In addition, many active antennas have either a pre-select filter, a post-select filter, or both. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 51 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Ensure that the antenna line impedance is 50ohm. Keep the antenna line on the PCB as short as possible to reduce the loss. Antenna line must have uniform characteristics, constant cross section, avoid meanders and abrupt curves. Keep one layer of the PCB used only for the Ground plane, if possible. Surround (on the sides, over and under) the antenna line on PCB with Ground, avoid having other signal tracks facing directly the antenna line of track. The ground around the antenna line on PCB has to be strictly connected to the Ground Plane by placing vias once per 2mm at least. Place EM noisy devices as far as possible from HE910 antenna line. Keep the antenna line far away from the HE910 power supply lines. Keep the antenna line far away from the HE910 GSM RF lines. If you have EM noisy devices around the PCB hosting the HE910, such as fast switching ICs, take care of the shielding of the antenna line by burying it inside the layers of PCB and surround it with Ground planes, or shield it with a metal frame cover. If you do not have EM noisy devices around the PCB of HE910, use a strip-line on the superficial copper layer for the antenna line. The line attenuation will be lower than a buried one. RF Trace losses are difficult to estimate on a PCB without having the appropriate tables or RF simulation software to estimate what the losses would be. A good rule of thumb would be to keep the RF traces as short as possible, make sure they are 50 ohms impedance and don’t contain any sharp bends. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 52 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 module contains a SAW filter used in a pre-select configuration with the built-in LNA, that is, the RF input of the HE910 ties directly into the SAW filter. Any circuit connected to the input of the HE910 would see complex impedance presented by the SAW filter, particularly out of band, rather than the relatively broad and flat return loss presented by the LNA. Filter devices pass the desired in band signal to the output, resulting in low reflected energy (good return loss), and reject the out of band signal by reflecting it back to the input, resulting in high reflected energy (bad return loss). If an external amplifier is to be used with the HE910, the overall design should be checked for RF stability to prevent the external amplifier from oscillating. Amplifiers that are unconditionally stable at the output will be fine to use with the HE910. If an external filter is to be connected directly to the HE910, care needs to be used in making sure neither the external filter nor the internal SAW filter performance is compromised. These components are typically specified to operate into 50 ohms impedance, which is generally true in band, but would not be true out of band. If there is extra gain associated with the external filter, then a 6 dB Pi or T resistive attenuator is suggested to improve the impedance match between the two components. The HE910 can be used with an external LNA such as what might be found in an active antenna. Because of the internal LNA, the overall gain (including signal losses past the external LNA) should not exceed 14 dB. Levels higher than that can affect the jamming detection capability of the HE910. If a higher gain LNA is used, either a resistive Pi or T attenuator can be inserted after the LNA to bring the gain down to 14 dB . The external LNA should have a noise figure better than 1 dB. This will give an overall system noise figure of around 2 dB assuming the LNA gain is 14 dB, or if higher the low gain mode is automatically managed by the HE910 with its internal AGC. The external LNA, if having no pre-select filter, needs to be able to handle other signals other than the GPS signal. These signals are typically at much higher levels. The amplifier needs to stay in the linear region when presented with these other signals. Again, the system designer needs to determine all of the unintended signals and their possible levels that can be presented and make sure the external LNA will not be driven into compression. If this were to happen, the GPS signal itself would start to be attenuated and the GPS performance would suffer. The external LNA needs a source of power. Many of the active antennas accept a 3 volt or 5 volt DC voltage that is impressed upon the RF signal line. This voltage is not supplied by the HE910, but can be easily supplied by the host design. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 53 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 is already provided by an internal LNA. In case the Application needs to include an additional LNA stage, the module is provided by a digital signal usable to enable the power supply of the external amplifier. The signal is set to High only when the GPS receiver is active. The electrical characteristics of the GPS_LNA_EN signal are: Level Min Max Output high level 1.6V 1.9 Output low level 0V 0.2V An example of GPS Antenna Supply circuit is shown in the following image: NOTE: The maximum DC voltage applicable to the ANT_GPS pin is 5V. In case this is exceeded, a series capacitor has to be included in the design to avoid exceeding the maximum input DC level. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 54 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Shielding the RF circuitry generally is ineffective because the interference is getting into the GPS antenna itself, the most sensitive portion of the RF path. The antenna cannot be shielded because then it can’t receive the GPS signals. There are two solutions, one is to move the antenna away from the source of interference or the second is to shield the digital interference to prevent it from getting to the antenna. The HE910 due to its characteristics of sensitivity is capable to perform a Fix inside the buildings. (In any case the sensitivity could be affected by the building characteristics i.e. shielding). The Antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Antenna must not be installed inside metal cases. Antenna must be installed also according to the Antenna manufacturer instructions. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 55 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The following table shows the logic level specifications used in the HE910 interface circuits: Absolute Maximum Ratings -Not Functional Parameter Min Max Input level on any digital pin (CMOS 1.8) with respect to ground -0.3V 3.1V Operating Range - Interface levels (1.8V CMOS) Level Min Max Input high level 1.5V 1.9V Input low level 0V 0.35V Output high level 1.6V 1.9 Output low level 0V 0.2V Current characteristics (Preliminary values) Level Typical Output Current 1mA Input Current 1uA Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 56 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 module is provided by two Reset lines that are described in the following table: Signal Function I/O PAD HW_SHUTDOWN* Phone Unconditional Shut Down R13 RESET* Phone reset P11 Unconditional Shutdown of the module. It will NOT perform the detach from the cellular network Power-cycle of the module, but will NOT perform the detach from the cellular network RESET* and HW_SHUTDOWN are used to reset the HE910. Whenever those signals are pulled low, the HE910 is reset. When the device is reset it stops any operation. After the release of the reset HE910 is unconditionally shut down (in case of HW_SHUTDOWN*) or restart (in case of RESET*), without doing any detach operation from the network where it is registered. This behaviour is not a proper shut down because any GSM device is requested to issue a detach request on turn off. For this reason the Reset signal must not be used to normally shutting down the device, but only as an emergency exit in the rare case the device remains stuck waiting for some network response. The RESET* and HW_SHUTDOWN* are internally controlled on start-up to achieve always a proper power-on reset sequence, so there's no need to control the pins on start-up. They may only be used to reset a device already on that is not responding to any command. NOTE: Do not use those signals to power off the HE910. Use the ON/OFF signal to perform this function or the AT#SHDN command. Reset Signal Operating levels: Signal Input high Input low Min 1.5V 0V Max 1.9V 0.35V * this signal is internally pulled up so the pin can be left floating if not used. If unused, this signal may be left unconnected. If used, then it must always be connected with an open collector transistor, to permit to the internal circuitry the power on reset and under voltage lockout functions. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 57 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 includes one integrated universal serial bus (USB) transceiver: USB 2.0 HS This port is compliant with the USB 2.0 specifications. The following table is listing the available signals: PAD Signal I/O Function Type B15 USB_D+ I/O USB differential Data (+) 3.3V C15 USB_D- I/O USB differential Data (-) 3.3V A13 VUSB AI Power sense for the internal USB transceiver. 5V NOTE Accepted range: 4.4V to 5.25V The USB_DPLUS and USB_DMINUS signals have a clock rate of 480 MHz. The signal traces should be routed carefully. Trace lengths, number of vias and capacitive loading should be minimized. The impedance value should be as close as possible to 90 Ohms differential. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 58 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 Module is provided by one SPI interface. The SPI interface defines two handshake lines for flow control and mutual wake-up of the modem and the Application Processor: SRDY (slave ready) and MRDY (master ready). The AP has the master role, that is, it supplies the clock. The following table is listing the available signals: PAD Signal I/O Function Type COMMENT D15 SPI_MOSI SPI MOSI CMOS 1.8V Shared with TX_AUX E15 SPI_MISO SPI MISO CMOS 1.8V Shared with RX_AUX F15 SPI_CLK SPI Clock CMOS 1.8V H15 SPI_MRDY SPI_MRDY CMOS 1.8V J15 SPI_SRDY SPI_SRDY CMOS 1.8V The signal 1V8_SEL must be connected to the VDD_IO1 input pin to properly supply this digital section. NOTE: Due to the shared functions, when the SPI port is used, it is not possible to use the AUX_UART port. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 59 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 SPI_MISO E15 SPI_MOSI D15 SPI_CLK F15 SPI_MRDY H15 HE910 SPI_SRDY J15 VDD_IO1 D13 1V8_SEL E13 D14 AP nc Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 60 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 module is provided with by 2 Asynchronous serial ports: MODEM SERIAL PORT 1 (Main) MODEM SERIAL PORT 2 (Auxiliary) Several configurations can be designed for the serial port on the OEM hardware, but the most common are: RS232 PC com port microcontroller UART @ 1.8V (Universal Asynchronous Receive Transmit) microcontroller UART @ 5V or other voltages different from 1.8V Depending from the type of serial port on the OEM hardware a level translator circuit may be needed to make the system work. On the HE910 the ports are CMOS 1.8.. The electrical characteristics of the Serial ports are explained in the following tables: Absolute Maximum Ratings -Not Functional Parameter Input level on any digital pin (CMOS 1.8) with respect to ground Min Max -0.3V 3.1V Operating Range - Interface levels (1.8V CMOS) Level Min Max Input high level 1.5V 1.9V Input low level 0V 0.35V Output high level 1.6V 1.9 Output low level 0V 0.2V Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 61 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The serial port 1 on the HE910 is a +1.8V UART with all the 7 RS232 signals. It differs from the PC-RS232 in the signal polarity (RS232 is reversed) and levels. RS232 Pin # Signal C109/DCD HE910 Pad Number N14 C104/RXD M15 C103/TXD N15 C108/DTR Name Usage Data Carrier Detect Transmit line *see Note Receive line *see Note Data Terminal Ready Output from the HE910 that indicates the carrier presence GND C107/DSR M14 M12, B13, P13, E14 … P14 C106/CTS P15 Clear to Send Output transmit line of HE910 UART Input receive of the HE910 UART Input to the HE910 that controls the DTE READY condition Ground Ground Data Set Ready Output from the HE910 that indicates the module is ready Output from the HE910 that controls the Hardware flow control Input to the HE910 that controls the Hardware flow control Output from the HE910 that indicates the incoming call condition C105/RTS L14 Request to Send C125/RING R14 Ring Indicator The following table shows the typical input value of internal pull-up resistors for RTS DTR and TXD input lines and in all module states: RTS DTR TXD STATE ON OFF RESET POWER SAVING 5K to 12K Schottky diode Schottky diode Pull up tied to 1V8 5K to 12K Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved 1V8 page 62 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The input line ON_OFF and RESET state can be treated as in picture below NOTE: According to V.24, some signal names are referred to the application side, therefore on the HE910 side these signal are on the opposite direction: TXD on the application side will be connected to the receive line (here named C103/TXD) RXD on the application side will be connected to the transmit line (here named C104/RXD) NOTE: For a minimum implementation, only the TXD, RXD lines can be connected, the other lines can be left open provided a software flow control is implemented. NOTE: In order to avoid a back powering effect it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the HE910 when the module is powered off or during an ON/OFF transition. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 63 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The secondary serial port on the HE910 is a CMOS1.8V with only the RX and TX signals. The signals of the HE910 serial port are: PAD Signal I/O Function Type COMMENT D15 TX_AUX Auxiliary UART (TX Data to DTE) CMOS 1.8V SHARED WITH SPI_MTSR E15 RX_AUX Auxiliary UART (RX Data from DTE) CMOS 1.8V SHARED WITH SPI_MRST The signal 1V8_SEL must be connected to the VDD_IO1 input pin in order to use this port. NOTE: Due to the shared pins, when the Modem Serial port is used, it is not possible to use the SPI functions. NOTE: In order to avoid a back powering effect it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the HE910 when the module is powered off or during an ON/OFF transition. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 64 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 In order to interface the HE910 with a PC com port or a RS232 (EIA/TIA-232) application a level translator is required. This level translator must: invert the electrical signal in both directions; Change the level from 0/1.8V to +15/-15V. Actually, the RS232 UART 16450, 16550, 16650 & 16750 chipsets accept signals with lower levels on the RS232 side (EIA/TIA-562), allowing a lower voltage-multiplying ratio on the level translator. Note that the negative signal voltage must be less than 0V and hence some sort of level translation is always required. The simplest way to translate the levels and invert the signal is by using a single chip level translator. There are a multitude of them, differing in the number of drivers and receivers and in the levels (be sure to get a true RS232 level translator not a RS485 or other standards). By convention the driver is the level translator from the 0-1.8V UART to the RS232 level. The receiver is the translator from the RS232 level to 0-1.8V UART. In order to translate the whole set of control lines of the UART you will need: 5 drivers 3 receivers Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 65 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 An example of RS232 level adaptation circuitry could be done using a MAXIM transceiver (MAX218) In this case the chipset is capable to translate directly from 1.8V to the RS232 levels (Example done on 4 signals only). The RS232 serial port lines are usually connected to a DB9 connector with the following layout: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 66 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The Audio of the HE910 Module is carried by DVI digital audio interface. The audio port can be directly connected to end device using digital interface, or via one of the several compliant codecs (in case an analog audio is needed). The product is providing the Digital Audio Interface (DVI) on the following Pins: Digital Voice Interface (DVI) PAD Signal I/O B9 DVI_WA0 I/O B6 DVI_RX Function Digital Audio Interface (Word Alignment / LRCLK) Digital Audio Interface (RX) Note Type CMOS 1.8V CMOS 1.8V B7 DVI_TX Digital Audio Interface (TX) CMOS 1.8V B8 DVI_CLK I/O Digital Audio Interface (BCLK) CMOS 1.8V Please refer to the HE910 Digital Audio Application note. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 67 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 module is provided by a set of Digital Input / Output pins Input pads can only be read; they report the digital value (high or low) present on the pad at the read time. Output pads can only be written or queried and set the value of the pad output. An alternate function pad is internally controlled by the HE910 firmware and acts depending on the function implemented. The following table shows the available GPIO on the HE910: PAD Signal I/O Function Type Drive strength Default State Note Alternate function STAT LED C8 GPIO_01 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT C9 GPIO_02 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT C10 GPIO_03 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT C11 GPIO_04 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT B14 GPIO_05 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT C12 GPIO_06 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT C13 GPIO_07 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT K15 GPIO_08 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT L15 GPIO_09 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT G15 GPIO_10 I/O Configurable GPIO CMOS 1.8V 0.1 mA INPUT Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved VDD_IO1 has to be connected to 1V8_SEL VDD_IO1 has to be connected to 1V8_SEL VDD_IO1 has to be connected to 1V8_SEL page 68 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Where not specifically stated, all the interface circuits work at 1.8V CMOS logic levels. The following table shows the logic level specifications used in the HE910 interface circuits: Absolute Maximum Ratings -Not Functional Parameter Min Max Input level on any digital pin (CMOS 1.8) with respect to ground -0.3V 3.1V Operating Range - Interface levels (1.8V CMOS) Level Min Max Input high level 1.5V 1.9V Input low level 0V 0.35V Output high level 1.6V 1.9 Output low level 0V 0.2V Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 69 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The GPIO pads, when used as inputs, can be connected to a digital output of another device and report its status, provided this device has interface levels compatible with the 1.8V CMOS levels of the GPIO. If the digital output of the device to be connected with the GPIO input pad has interface levels different from the 1.8V CMOS, then it can be buffered with an open collector transistor with a 47K pull up to 1.8V. NOTE: In order to avoid a back powering effect it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the HE910 when the module is powered off or during an ON/OFF transition. The GPIO pads, when used as outputs, can drive 1.8V CMOS digital devices or compatible hardware. When set as outputs, the pads have a push-pull output and therefore the pull-up resistor may be omitted. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 70 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The STAT_LED pin status shows information on the network service availability and Call status. The function is available as alternate function of GPIO_01 In the HE910 modules, the STAT_LED needs an external transistor to drive an external LED. Therefore, the status indicated in the following table is reversed with respect to the pin status. LED status Permanently off Fast blinking (Period 1s, Ton 0,5s) Slow blinking (Period 3s, Ton 0,3s) Permanently on Device Status Device off Net search / Not registered / turning off Registered full service a call is active A schematic example could be: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 71 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The VRTC pin brings out the Real Time Clock supply, which is separate from the rest of the digital part, allowing having only RTC going on when all the other parts of the device are off. To this power output a backup capacitor can be added in order to increase the RTC autonomy during power off of the battery. NO Devices must be powered from this pin. Please refer to the related User Guide (SIM Holder Design Guides, 80000NT10001a). A regulated power supply output is provided in order to supply small devices from the module. The signal is present on Pad R11 and it is in common with the PWRMON (module powered ON indication) function. This output is always active when the module is powered ON. The operating range characteristics of the supply are: Level Output voltage Output current Output bypass capacitor (inside the module) Min Typical Max 1.78V 1.80V 1.82V 60mA 1uF Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 72 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 is provided by one AD converter. It is able to read a voltage level in the range of 0÷1.2 volts applied on the ADC pin input, store and convert it into 10 bit word. The following table is showing the ADC characteristics: Input Voltage range AD conversion Input Resistance Input Capacitance Min Typical Max 1.2 10 Units Volt bits Mohm pF The input line is named as ADC_IN1 and it is available on Pad B1 An AT command is available to use the ADC function. The command is AT#ADC=1,2 The read value is expressed in mV Refer to SW User Guide or AT Commands Reference Guide for the full description of this function. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 73 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 modules have been designed in order to be compliant with a standard lead-free SMT process. Pin B1 Bottom view Dimensions in mm Lead-free Alloy: Surface finishing Ni/Au for all solder pads Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 74 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 75 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 TOP VIEW In order to easily rework the HE910 is suggested to consider on the application a 1.5 mm placement inhibit area around the module. It is also suggested, as common rule for an SMT component, to avoid having a mechanical part of the application in direct contact with the module. NOTE: In the customer application, the region under WIRING INHIBIT (see figure above) must be clear from signal or ground paths. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 76 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Stencil’s apertures layout can be the same of the recommended footprint (1:1), we suggest a thickness of stencil foil ≥ 120 µm. Non solder mask defined (NSMD) type is recommended for the solder pads on the PCB. Copper Pad Solder Mask PCB SMD (Solder Mask Defined) NSMD (Non Solder Mask Defined) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 77 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The recommendation for the PCB pads dimensions are described in the following image (dimensions in mm) Solder resist openings Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 78 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 It is not recommended to place via or micro-via not covered by solder resist in an area of 0,3 mm around the pads unless it carries the same signal of the pad itself (see following figure). Inhibit area for micro-via Holes in pad are allowed only for blind holes and not for through holes. Recommendations for PCB pad surfaces: Finish Electro-less Ni / Immersion Au Layer thickness [µm] 3 –7 / 0.05 – 0.15 Properties good solder ability protection, high shear force values The PCB must be able to resist the higher temperatures which are occurring at the lead-free process. This issue should be discussed with the PCB-supplier. Generally, the wettability of tin-lead solder paste on the described surface plating is better compared to lead-free solder paste. It is not necessary to panel the application’s PCB, however in that case it is suggested to use milled contours and predrilled board breakouts; scoring or v-cut solutions are not recommended. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 79 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Solder paste Lead free Sn/Ag/Cu We recommend using only “no clean” solder paste in order to avoid the cleaning of the modules after assembly. Recommended solder reflow profile: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 80 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Profile Feature Average ramp-up rate (TL to TP) Preheat – Temperature Min (Tsmin) – Temperature Max (Tsmax) – Time (min to max) (ts) Tsmax to TL – Ramp-up Rate Time maintained above: – Temperature (TL) – Time (tL) Peak Temperature (Tp) Time within 5°C of actual Peak Temperature (tp) Ramp-down Rate Time 25°C to Peak Temperature Pb-Free Assembly 3°C/second max 150°C 200°C 60-180 seconds 3°C/second max 217°C 60-150 seconds 245 +0/-5°C 10-30 seconds 6°C/second max. 8 minutes max. NOTE: All temperatures refer to topside of the package, measured on the package body surface WARNING: The HE910 module withstands one reflow process only. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 81 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 modules are packaged on trays of 20 pieces each. These trays can be used in SMT processes for pick & place handling. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 82 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 83 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910 is a Moisture Sensitive Device level 3, in according with standard IPC/JEDEC JSTD-020, take care all the relatives requirements for using this kind of components. Moreover, the customer has to take care of the following conditions: a) Calculated shelf life in sealed bag: 12 months at <40°C and <90% relative humidity (RH). b) Environmental condition during the production: 30°C / 60% RH according to IPC/JEDEC J-STD-033A paragraph 5. c) The maximum time between the opening of the sealed bag and the reflow process must be 168 hours if condition b) “IPC/JEDEC J-STD-033A paragraph 5.2” is respected d) Baking is required if conditions b) or c) are not respected e) Baking is required if the humidity indicator inside the bag indicates 10% RH or more Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 84 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc Where there is risk of explosion such as gasoline stations, oil refineries, etc It is responsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode. The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information’s are available on the European Community website: http://europa.eu.int/comm/enterprise/rtte/dir99-5.htm The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at: http://europa.eu.int/comm/enterprise/electr_equipment/index_en.htm Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 85 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910, HE910-D, HE910-GA, HE910-EUG, HE910-EUR, HE910-EUD, HE910-NAG, HE910NAR, HE910-NAD modules have been evaluated against the essential requirements of the 1999/5/EC Directive. Bulgarian Czech Danish Dutch English Estonian German Greek Hungarian Finnish French Icelandic Italian С настоящето Telit Communications S.p.A. декларира, че 2G/3G module отговаря на съществените изисквания и другите приложими изисквания на Директива 1999/5/ЕС. Telit Communications S.p.A. tímto prohlašuje, že tento 2G/3G module je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Undertegnede Telit Communications S.p.A. erklærer herved, at følgende udstyr 2G/3G module overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Hierbij verklaart Telit Communications S.p.A. dat het toestel 2G/3G module in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hereby, Telit Communications S.p.A., declares that this 2G/3G module is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Käesolevaga kinnitab Telit Communications S.p.A. seadme 2G/3G module vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Hiermit erklärt Telit Communications S.p.A., dass sich das Gerät 2G/3G module in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. ΜΕ ΣΗΝ ΠΑΡΟΤΑ Telit Communications S.p.A. ΔΗΛΩΝΕΙ ΟΣΙ 2G/3G module ΤΜΜΟΡΦΩΝΕΣΑΙ ΠΡΟ ΣΙ ΟΤΙΩΔΕΙ ΑΠΑΙΣΗΕΙ ΚΑΙ ΣΙ ΛΟΙΠΕ ΥΕΣΙΚΕ ΔΙΑΣΑΞΕΙ ΣΗ ΟΔΗΓΙΑ 1999/5/ΕΚ. Alulírott, Telit Communications S.p.A. nyilatkozom, hogy a 2G/3G module megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Telit Communications S.p.A. vakuuttaa täten että 2G/3G module tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Par la présente Telit Communications S.p.A. déclare que l'appareil 2G/3G module est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Hér með lýsir Telit Communications S.p.A. yfir því að 2G/3G module er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC Con la presente Telit Communications S.p.A. dichiara che questo 2G/3G module è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 86 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Ar šo Telit Communications S.p.A. deklarē, ka 2G/3G module atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lithuanian Šiuo Telit Communications S.p.A. deklaruoja, kad šis 2G/3G module atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Maltese Hawnhekk, Telit Communications S.p.A., jiddikjara li dan 2G/3G module jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Norwegian Telit Communications S.p.A. erklærer herved at utstyret 2G/3G module er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF. Polish Niniejszym Telit Communications S.p.A. oświadcza, że 2G/3G module jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC Portuguese Telit Communications S.p.A. declara que este 2G/3G module está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovak Telit Communications S.p.A. týmto vyhlasuje, že 2G/3G module spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Slovenian Telit Communications S.p.A. izjavlja, da je ta 2G/3G module v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Spanish Por medio de la presente Telit Communications S.p.A. declara que el 2G/3G module cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Swedish Härmed intygar Telit Communications S.p.A. att denna 2G/3G module står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Latvian In order to satisfy the essential requirements of 1999/5/EC Directive, the HE910, HE910-GA, HE910-EUG modules are compliant with the following standards: RF spectrum use (R&TTE art. 3.2) EN 300 440-2 V1.4.1 EN 301 511 V9.0.2 EN 301 908-1 V4.2.1 EN 301 908-2 V4.2.1 EMC (R&TTE art. 3.1b) EN 301 489-1 V1.8.1 EN 301 489-3 V1.4.1 EN 301 489-7 V1.3.1 EN 301 489-24 V1.5.1 Health & Safety (R&TTE art. 3.1a) EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 In order to satisfy the essential requirements of 1999/5/EC Directive, the HE910-NAG modules are compliant with the following standards: RF spectrum use (R&TTE art. 3.2) EN 300 440-2 V1.4.1 EN 301 511 V9.0.2 EMC (R&TTE art. 3.1b) EN 301 489-1 V1.8.1 EN 301 489-3 V1.4.1 EN 301 489-7 V1.3.1 Health & Safety (R&TTE art. 3.1a) EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 87 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 The HE910-D, HE910-EUR, HE910-EUD modules are compliant with the following standards: RF spectrum use (R&TTE art. 3.2) EMC (R&TTE art. 3.1b) Health & Safety (R&TTE art. 3.1a) EN 301 511 V9.02 EN 301 908-1 V4.2.1 EN 301 908-2 V4.2.1 EN 301 489-1 V1.8.1 EN 301 489-7 V1.3.1 EN 301 489-24 V1.5.1 EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 The HE910-NAR, HE910-NAD modules are compliant with the following standards: RF spectrum use (R&TTE art. 3.2) EN 301 511 V9.02 EMC (R&TTE art. 3.1b) EN 301 489-1 V1.8.1 EN 301 489-7 V1.3.1 EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 Health & Safety (R&TTE art. 3.1a) The conformity assessment procedure referred to in Article 10 and detailed in Annex IV of Directive 1999/5/EC has been followed with the involvement of the following Notified Body: AT4 wireless, S.A. Parque Tecnologico de Andalucía C/ Severo Ochoa 2 29590 Campanillas – Málaga SPAIN Notified Body No: 1909 Thus, the following marking is included in the product: 1909 The full declaration of conformity can be found on the following address: http://www.telit.com/ There is no restriction for the commercialisation of the HE910, HE910-D, HE910-GA, HE910-EUG, HE910-EUR, HE910-EUD, HE910-NAG, HE910-NAR, HE910-NAD modules in all the countries of the European Union. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 88 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Final product integrating this module must be assessed against essential requirements of the 1999/5/EC (R&TTE) Directive. It should be noted that assessment does not necessarily lead to testing. Telit Communications S.p.A. recommends carrying out the following assessments: RF spectrum use (R&TTE art. 3.2) It will depend on the antenna used on the final product. EMC (R&TTE art. 3.1b) Testing Health & Safety (R&TTE art. 3.1a) Testing Alternately, assessment of the final product against EMC (Art. 3.1b) and Electrical safety (Art. 3.1a) essential requirements can be done against the essential requirements of the EMC and the LVD Directives: Low Voltage Directive 2006/95/EC and product safety Directive EMC 2004/108/EC for conformity for EMC Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 89 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Modification statement Telit has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Telit n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur. Interference statement This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Wireless notice This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below: Frequency band GSM 850/FDD V PCS 1900/FDD II FDD IV HE910, HE910-D 5.22 dBi 3.31 dBi 6.45 dBi HE910-GA 5.22 dBi 3.31 dBi HE910-NAR, HE910-NAD, HE910-NAG 5.29 dBi 4.02 dBi 6.32 dBi This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 90 of 91 HE910 Hardware User Guide 1vv0300925 Rev.18 – 15-06-2012 Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps. Gain de l'antenne doit être ci-dessous: Bande de fréquence GSM 850/FDD V PCS 1900/FDD II FDD IV HE910, HE910-D 5.22 dBi 3.31 dBi 6.45 dBi HE910-GA 5.22 dBi 3.31 dBi HE910-NAR, HE910-NAD, HE910-NAG 5.29 dBi 4.02 dBi 6.32 dBi L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur. FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 91 of 91
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 91 Language : it-IT Tagged PDF : Yes Title : HE910 Hardware User Guide Author : F D Creator : Microsoft® Office Word 2007 Create Date : 2012:06:15 16:39:16 Modify Date : 2012:06:15 16:39:16 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools