Telular 052651 Desktop PCS Transceiver - Phonecell User Manual 5602xxxx SX5D GSM Technical Manual

Telular Corporation Desktop PCS Transceiver - Phonecell 5602xxxx SX5D GSM Technical Manual

Contents

SX5D manual

01/30/02 Part Number 5602xxxxPHONECELL®SX5D GSMDESKTOPPHONE900/1800 MHZGSM (DUALBAND)1900 MHZGSMVOICECOMMUNICATION ANDCOMPUTERFAX/DATATECHNICALMANUAL
STANDARD CONNECTIONSDESKPHONE MODEL ONLYPhonecell®SX5D 2Technical Manual
FAX PHONE MODEL ONLYPERSONAL LEAST COST ROUTING MODEL ONLYPhonecell®SX5D 3Technical Manual
Phonecell®SX5D 4Technical ManualBefore installing your Phonecell®SX5D, carefully remove the contents from the shipping cartonand check for evidence of shipping damage. If damage is found, contact your AuthorizedTelular Distributor or shipping agent immediately.SAFE OPERATION INSTRUCTIONSIMPORTANT! Before installing or operating this product, read the SAFETY AND GENERALINFORMATION section of this manual.•  Install unit indoors.•  Install unit on hard, flat surface for proper ventilation.•  Do not expose unit to rain or moisture.•Do not place unit on or close to sources of heatIMPORTANT NOTICESTERMS AND CONDITIONS FOR USE OF PHONECELL®PRODUCTS ("Product")These Terms and Conditions are a legal contract between you and Telular Corporation for the title to and use of the Product.BY RETAINING AND USING THE PRODUCT AFTER RECEIPT OF IT, YOU AGREE TO THE TERMS AND CONDITIONSINCLUDING WARRANTY DISCLAIMERS, LIMITATIONS OF LIABILITY AND INDEMNIFICATION PROVISIONS BELOW. IFYOU DO NOT AGREE TO THE TERMS AND CONDITIONS, DO NOT USE THE PRODUCT AND IMMEDIATELY RETURNTHE UNUSED PRODUCT FOR A COMPLETE REFUND. You agree to accept sole responsibility for any misuse of the Productby you; and, in addition, any negligent or illegal act or omission of your or your agents, contractors, servants, employees, orother users of the Product so long as the Product was obtained from you, in the use and operation of the Product. Changes ormodifications not expressly approved by Telular Corporation will void your authority to operate the equipment per FCC part 15paragraph 15.21.INDEMNIFICATION OF TELULAR CORPORATION ("TELULAR")YOU SHALL INDEMNIFY, DEFEND AND HOLD HARMLESS TELULAR FOR ANY OF THE COST, INCLUDING REA-SONABLE ATTORNEYS' FEES, AND FROM CLAIMS ARISING OUT OF YOU, YOUR CLIENTS' OR OTHER THIRDPARTIES' USE OR OPERATION OF THE PRODUCT: (i) FOR MISUSE OR IN A MANNER NOT CONTEMPLATED BYYOU AND TELULAR OR INCONSISTENT WITH THE PROVISIONS OF THIS MANUAL; (ii) IN AN ILLEGAL MANNEROR AGAINST PUBLIC POLICY; (iii) IN A MANNER SPECIFICALLY UNAUTHORIZED IN THIS MANUAL; (iv) IN A MAN-NER HARMFUL OR DANGEROUS TO THIRD PARTIES; (v) FROM CLAIMS BY ANYONE RESPECTING PROBLEMS,ERRORS OR MISTAKES OF THE PRODUCT; OR (vi) COMBINATION OF THE PRODUCT WITH MATERIAL, MODIFI-CATION OF THE PRODUCT OR USE OF THE PRODUCT IN AN ENVIRONMENT NOT PROVIDED, OR PERMITTED, BYTELULAR IN WRITING. THE PARTIES SHALL GIVE EACH OTHER PROMPT NOTICE OF ANY SUCH COST ORCLAIMS AND COOPERATE, EACH WITH THE OTHER, TO EFFECTUATE THIS INDEMNIFICATION, DEFENSE ANDHOLD HARMLESS.CONTENTSTELULAR CORPORATIONCorporate Headquarters647 North Lakeview ParkwayVernon Hills, Illinois 60061, USATechnical SupportTel: 847-247-9400 · Fax: 847-247-0021E-mail: mainoffice@telular.com · http://www.telular.comPower SupplyPhonecell®SX5D GSM Desktop Phone Spike AntennaPLEASE SEE  THE  IMPORTANT NOTICES  SECTION OF THIS MANUAL FOR IMPORTANT INFORMATION ON USE, WARRANTY AND INDEMNIFICATION
TABLE OF CONTENTSIMPORTANT NOTICES..................................................................................................2Technical Support.......................................................................................................2INSTALLATION..............................................................................................................5Location and Setup ....................................................................................................5Connect the Handset ...................................................................................................Optional Wedge ...........................................................................................................Wall Mounting...............................................................................................................Connect Your Phonecell®SX5D to AC Power..............................................................Battery Backup.............................................................................................................External Connectors.....................................................................................................OPERATION.....................................................................................................................Function Keys ..............................................................................................................LCD Display .................................................................................................................SIM Card Installation ....................................................................................................SIM PIN Setup .............................................................................................................Service Indication .........................................................................................................Network Registration....................................................................................................Call Functions ..............................................................................................................Volume .........................................................................................................................Alert Tones ...................................................................................................................Speakerphone..............................................................................................................Internal Phone Book ....................................................................................................Speed Dial....................................................................................................................FEATURES.......................................................................................................................Call Log........................................................................................................................Keypad Tones ..............................................................................................................Warning Tones .............................................................................................................Date and Time..............................................................................................................Alarm ............................................................................................................................Display Phone Number ................................................................................................Greeting Message........................................................................................................Screen Contrast ...........................................................................................................Reset System Defaults.................................................................................................Restrict Phone Use ......................................................................................................SUPPLEMENTARY FEATURES (NETWORK DEPENDENT) ........................................Call Forwarding............................................................................................................Call Waiting ..................................................................................................................Three-Way Calling........................................................................................................Voicemaill .....................................................................................................................Short Message Service (SMS).....................................................................................Info Messages ..............................................................................................................In-Call Options .............................................................................................................Phonecell®SX5D 5Technical Manual
TABLE OF CONTENTS (CONTINUED)DIGITAL DATA SERVICE ................................................................................................Standard Modem Setting .............................................................................................Sending and Receiving Digital Fax..............................................................................TECHNICIAN COMMANDS.............................................................................................SAFETY INFORMATION .................................................................................................WARRANTY .....................................................................................................................Appendix A: How to Setup PC Serial Ports for Phonecell®Computer Digital Fax/Data .............................................................................................Phonecell®SX5D 6Technical Manual
Phonecell®SX5D 7Technical ManualINSTALLATIONSX5D Location and SetupThe SX5D comes with a standard spike antenna (TNC).1)  Choose location that is above ground and as close to windows (or exterior walls) as possibleto get the best signal - see Figure 2)  Finger-tighten the antenna; do not over-tighten.Connect the HandsetBefore you can use your Phonecell®SX5, you must connect the handset cable to the SX5D.Insert the cable into the phone jack - see Figure Figure  – For optimal call clarity, the antenna should be pointed up and the SX5D located close to an exterior wall or window.Figure  – SX5D handset connection.Handset cablePhone jack
SIM Card InstallationThe SX5D requires a Subscriber Identification Module (SIM) for normal operation. The serviceprovider supplies the SIM card, which carries the account information needed to operate theSX5D. The SIM compartment is on the back of the Phonecell®SX5.NOTE: If you don’t have a SIM card, contact your network service provider.1)  Remove the power supply if you have already connected it. You must remove the powersupply whenever you install or remove a SIM Card.2)  Remove the SIM compartment cover by removing the screw. See Figure.3)  Open the SIM compartment holder.4)  Line up the SIM card with the arrow on the SIM card holder. See Figure.5)  Gently insert the SIM card in the slot of the SIM card holder.6)  Close the SIM card holder.NOTE: If you insert the SIM card improperly, the holder will not  close. Do not force the holdershut. Make sure the SIM card is aligned properly with the directional arrow on the holder.7)  Reattach the SIM compartment cover with the screw.8)  Attach the power supply.Phonecell®SX5D 8Technical ManualSIMCompartmentCoverSIM CardHolderSIM CardSIMCompartmentCoverFigure -  Figure - Cover Screw
Phonecell®SX5D 9Technical ManualAttach the Optional Wedge1)  Slide the wedge tabs on one end of the wedge into the top wedge tab slots.2)  Snap the wedge tabs on the other end of the wedge into the bottom wedge tab slots.Using the Optional WedgeThe wedge is used to put the SX5D on an angle that makes it easier to see the display screen ifyou are sitting at a desk. If you mount it on a wall, the wedge offsets the natural angel of theSX5D so that the keypad is parallel to the wall rather than angled down into the wall. Attach for Wall Mounting Attach for Desk MountingTop wedge tabslotsBottom wedgetab slotsWedge tabsWedge tabsAttach thick end ofwedge at bottom ofthe SX5D.Attach thick end ofwedge at top of theSX5D.Figure -  Figure - Figure -  Figure -
Wall-Mounting1)  Remove the mounting clip from the cradle and re-insert it with the tab pointing up - seeFigures and .2)  Mark two hole locations 83 mm (3-1/4 inches) vertically apart and drill two holes into the wall.3)  Install the screws (not supplied) into the wall, leaving a gap of approximately 3 mm (1/8 inches) between the screw head and the wall.4)  Align the mounting holes with the screws and mount the SX5D onto the screws - seeFigures and.Phonecell®SX5D 10 Technical ManualFigure  – Mount the SX5D onto the screws.Figure  –  SX5D mounting hooks.MountingHolesInsertMountingClip intothe Cradle(tab up)Mounting Clip inCradle (tab up)Figure  – Handset mounting clip assembly forwall-mount applications.RemoveMounting Clipfrom the Cradle(tab down)Figure  – Handsetmounting clip assembly.
Phonecell®SX5D 11 Technical ManualBattery BackupHow to Install Battery1) Remove the battery access door screw located on the bottom of the unit.2) Press the battery access door tabs and remove the battery access door.3) Install 4 AA batteries 4) Reinstall the battery access door using the screw5) Turn the AC/Battery switch to battery operation**The SX5D does not support rechargeable batteriesBattery OperationThe unit will automatically switch from AC to battery upon loss of AC power. A fully charged bat-tery will provide up to two hours of talk time and 72 hours of standby. Total charging time is 15hours.Connect Your Phonecell®SX5 to AC Power1)  Connect the barrel connector of the power supply to the AC power input on the rear panel ofthe SX5D - see Figure .2)  Plug the power supply into the AC wall socket. The unit will power-up automatically.3)  Check the cellular signal strength and move the unit (or external antenna) until you achievethe best signal possible - see the Received Signal Strength section of this manual.Figure  – Battery Access Door.Battery AccessDoor ScrewBattery AccessDoor TabsBattery AccessDoor4 AA BatteriesAC Power InputAC wall socketPowerSupplyBarrel ConnectorAC/Battery switchFigure  – SX5D AC power input.Figure -Battery Installation
Back View----UPDATE:  THESE WILL CHANGE DEPENDING ON THE MODULE-----Side ViewPhonecell®SX5D 12 Technical ManualKeyboard Port(DIN)Serial Port(DB-9) Phone(RJ-11)AC/Battery SwitchFAX or PSTN(RJ-11)AC Power InputAntenna(TNC)Microphone
Phonecell®SX5D 13 Technical ManualOPERATIONFunction KeysOperation of the Phonecell®SX5 is accomplished though the function keys on the keypad of theunit - see Figure .LCD Display IconsIcons displayed on the LCD display indicate the features in use, the status of the phone, signalstrength and battery status - see Figure . Figure  –SX5D LCDdisplay icons.Figure  –SX5D Keypad and Function Keys.Received SignalStrength- Indicates thestrength of the currentsignal. The more bars,the stronger the signal.Message- Displays whenyou have a new text orvoicemail message.Speaker--indicates speaker phone isoff-hook.Call--indicates that the handsetis off-hookBattery- Indicates the level of batterypower. The more bars, the more power.ClockSoft keys--these keys will change when you enter different sub-menu’s to access the phone’s features. Press the correspondingsoft key buttons to use the soft keysAlarm- Indicates that youhave set the Phonecell’salarm.LCD Soft KeyButtonsLCD ScreenSpeakerphone andhandset volume controlRedialFlashMute  Speakerphone LED
Phonecell®SX5D 14 Technical ManualService IndicationFull ServiceWhen the power cord is connected properly, the SX5D will displaythe Telular logo, emit a power on tone, and the LED will light up.After a few seconds the greeting and mobile number will display. Ifyou have service, the antenna icon will display indicator lines toshow the signal strength.No ServiceWhen there is no service in your area, the antenna icon will haveno indicator lines. Contact your service provider to make sure cel-lular service is activated. No calls can be made in this case.Limited ServiceIf there is a signal, but full service with the system is blocked, onlyemergency calls will be allowed. Contact your service provider formore information.Network SettingsNetwork RegistrationIf the home network is unavailable, but there is another network available (either another fre-quency or system), then the SX5D will prompt to register to that system. If there is more thanone system, a list of available systems will display. 1)  Use the arrow keys to highlight a network from the list.2)  Press SELECT. If the selected network cannot be accessed, the list of available networks willbe updated and you will have to select a different one.Network Selection1)  Press MENU2)  Select Settings, then select Network Settings.3)  Select Select Network.4)  To use Automatic network selection, select Automatic.To use Manual network selection, select Manual and continuewith Step 5.5)  Select a network from the list.Preferred NetworksTo Insert New Entry1)  Press MENU2)  Select Settings, then select Network Settings.3)  Select Select Network.4)  Select Set Preferred.4)  Highlight the entry above which you want to insert a new preferred carrier.5)  Press SELECT.6)  Select Insert.7)  Select an entry from the list.To Delete Entry1)  Press MENU2)  Select Settings, then select Network Settings.3)  Select Select Network.4)  Select Set Preferred.5)  Select the entry you want to delete.6)  Select DeleteNo ServiceFull ServiceNew entry willbe insertedhere
To Add New Network1)  Press MENU.2)  Select Settings, then select Network Settings.3)  Select Add New Network. If you have already added some networks, a list of those net-works will display.4)  Select Add.If a list of networks displays, press the SELECT key, then select Add.5)  Enter the correct Country Code, Network Code, and Network Name as prompted.New networks will be added to the end of the list.To Edit or Delete an Added NetworkOnce you add a new network, you can edit the information you entered for that network, ordelete it.1)  Press MENU.2)  Select Settings, then select Network Settings.3)  Select Add New Network.4)  Select the network you want to edit or delete.5)  Select the option you want to use.To Change Network Password1)  Press MENU.2)  Select Settings, then select Network Settings.3)  Select Change Network Password4)  --NEED ADDITIONAL INFORMATION--SIM PIN SetupSIM PIN 1 controls access to SIM Card information. When On, it requires you to enter it eachtime the phone is turned on. When off it requires entry only when the SIM Card is put into aphone. Another user could still access your phone with a different SIM Card. To lock the phoneeven when a new SIM Card is inserted, see How to Lock the Phone. SIM PIN 2 accessesNetwork controlled features.To Turn On/Off SIM PIN 11)  Press the MENU key.2)  Select Settings, then select Security Settings.3)  Select SIM PIN 1.4)  Select On or Off.To Change SIM PIN 21)  Press the MENU key.2)  Select Settings, then select Security Settings.3)  Select SIM PIN 2.4)  Select Change PINYou will be prompted to enter the old PIN.5)  Enter the old PIN.6)  Enter the new PIN.It must be numerical and be between 4 and 8 digits long.7)  Press OK to save the new PIN, or use the CLEAR key to make changes.Phonecell®SX5D 15 Technical Manual
Phonecell®SX5D 16 Technical ManualTo Place a Call1)  Pick up the handset or press the Speaker phone button. TheSX5D is now “off-hook.”2)  Listen for dial tone.3)  Dial the phone number. The dialed number is displayed on thedisplay, along with the name if it is stored in your phonebook.To Correct Dialing Errors•  To erase one digit, press the CLEAR key once.•  To erase all digits, press and hold down the CLEAR key until alldigits are erased.To Redial the Last Telephone Number Dialed1)  Pick up the handset. The SX5D is now “off-hook”.2)  Press the REDIAL key.To Receive a CallWhen there is an incoming call, the SX5D rings, an incoming callnotification displays and blinks, and the LED blinks.1)  Pick up the handset or press the Speaker phone button.Press the REJECT key to refuse the call. Your phone will stopringing, and the calling party will be disconnected.2)  Begin talking.To Receive a Call When Caller ID is ActivatedThe Caller ID feature displays the caller’s number when the SX5Drings. If the caller’s name and number are stored together in thephonebook of your SX5D, the caller’s name and number will be displayed. Contact your service provider to activate this feature.NOTE: If there is a missed call (call is not answered), “MISSED CALLS” will be displayed.To End a CallHang up the phone (place the handset back onto the SX5D cradle).NOTE: If the call is ended by the other party, the SX5D will clear the line and re-establish a dialtone. The SX5D may be used for another call or may be hung up.To Mute a Call1)  While in a call, press the MUTE button.A message will notify you that the microphone is muted.2)  Press the MUTE button again to unmute the microphone.To Put a Call on Hold1)  While in a call, press the MENU key.2)  Select Hold.The display will change from Active to Held.3)  To activate the call, press the MENU key and select Retreive.To Adjust VolumesYou can control the levels on your phone for the keypad tones and conversation volume (whatyou hear through the handset or speaker) and the ring volume of an incoming call. You can alsoturn the keypad tones on or off.To Adjust External Speaker Volume1)  Press the Speaker key.2)  Press the UP/DOWN arrow keys accordingly to adjust volume.To Adjust Handset Volume1)  Pick up the handset 2)  Press UP/DOWN keys to adjust volume.Muted callCall on holdReceiving a call with CallerID activated.Receiving a callPlacing a call.Handset/Speaker Volume
To Adjust Phone Alert Volume (ringer)1)  Press the MENU key,2)  Select Settings, then Audio Settings.3)  Select Alert Volume and set desired volume level.NOTE: If you choose “Silent”, no alert will sound.To Change Alert TonesYou can set different alerts for different types of calls. This allowsyou to tell the difference between a voice call or an SMS mes-sage, for example, by the alert that sounds.1)  Press the MENU key2)  Select Settings, then Audio Settings.3)  Use the arrow keys to scroll through the alert types.4)  Select the alert you would like to change.5).  Select the alert sound you would like to use.To Use the Speaker Phone1)  Press the Speaker key.You will hear the dial tone through the speaker, and theSpeaker icon will display.2)  Enter the telephone number.Internal Phone BookYour SX5D has an “Internal Phone Book” in which you can store up to 99 telephone numberswith corresponding names. You can set them up for convenient one-touch or two-touch dialing.To Change Phone Book SettingsYou can save entries to the SIM card or to the phone memory. Ifyou save to the SIM card, you can transfer that SIM card to anoth-er phone and keep all your phone book entries. You also have theoption of selecting to choose where to save each entry as youenter it.1)  Press the MENU key.2)  Select Phonebook, then Settings3)  Scroll to and select Save Entries To.When you scroll to Save Entries To, the current setting will display.4)  Select where you would like to save phone book entries.To Use Keypad ButtonsThere are three or four letters assigned to each number on the telephone keypad. The letterson the keypad will display when you press the appropriate number. If you press the number 3,for example, a “D” will appear. If you press it twice, you will see the “E”, and if you press itthree times, the “F” will appear. The cusor will move on to the next space after a brief pause,so you must select the letter quickly.To Enter a Hard PauseHard pauses allow the SX5D to be used with a automated phone systems used for pagers orautomated banking. When you program a number into the phonebook, you can enter a pauseby pressing and holding “#” for more than one second. The hard pause will be displayed as “P.”NOTE:  This feature can only be used for phonebook entries.Phonecell®SX5D 17 Technical ManualPhonebook SettingsSpeakerphone off-hookChanging Alert Tones
Phonecell®SX5D 18 Technical ManualTo Add a New Entry to the Phonebook1)  Press the MENU key,2)  Select Phonebook, then select Add Name3)  Enter a name by pressing the alphanumeric keys. You can onlyinput 16 letters.NOTE: To correct errors in the name, press the CLEAR key.4)  Press the OK key.5)  Enter the desired telephone number (maximum of 30 digits).6)  Press the OK key.You will be prompted to enter another number.7)  Press OK to save the entry and return to the Phonebook menu.If you have additional numbers (up to 2 more) follow steps 5 through 7 for each number.To Search for a Number in Memory1)  Press the NAME key.2)  Use the arrow keys to scroll through the entries, or use the keypad to view all entries thatbegin with a specific letter.NOTE: If you use the arrow keys, the list will be in order of the most recently selected entries.3)  Press the SELECT key to view the phone number(s) listed for an entry that is highlighted.To Edit or Delete and Entry1)  Press the NAME key.2)  Use the arrow keys to scroll through the entries, or use thekeypad to view all entries that begin with a specific letter.NOTE: If you use the arrow keys, the list will be in order of themost recently selected entries.3)  Press the SELECT key to view the phone number(s) listed for an entry that is highlighted.4)  Press the OPTIONS key and select the option you wish to use.Speed DialingSpeed dialing permits one-touch dialing for up to 10 telephone numbers stored in the internalphone book.To Assign a Number to a Speed Dial Location1)  Press the NAME key.2)  Select the entry you wish to add to the speed dial list.3)  Press the OPTIONS key.4)  Select Add to Speed Dial.5)  Select the location (0 - 9).NOTE: The next available location will display automatically. You can select a specific locationby pressing the desired number on the keypad. If that location is already in use, you can replacethe phone number that was stored there with a new one.To Dial a Speed Dial Location1)  Pick up the handset or press the Speaker Phone key.2)  Press and hold the number of the location containing the number to be called.3)  The number is displayed and dials automatically.NOTE: If you skip Step 1, the phone will automatically go off-hook in speaker phone mode whenyou press and hold a number.To View the Speed Dial List1)  Press the MENU key.2)  Select Phonebook, then select Settings.3)  Select Speed dial list.Adding a phonebook entry
FEATURESCall LogsThe SX5D’s memory stores the telephone numbers of the last tenoutgoing calls and the last ten incoming calls along with the datesand times of the calls. You can display these numbers and theSX5D can dial them automatically from the call log.To View the Call Log1)  Press the MENU key.2)  Select Call Log.3)  Select which calls you would like to view (All, Missed,Received, Dialed).NOTE: Calls are denoted with the following icons:Dialed calls Missed calls Received callsTo Dial a number from the Call Log1)  View the Call Log.2)  Highlight the call with the number you wish to dial.3)  Pick up the handset or press the Speaker Phone button.4)  A dial tone will sound, then the number will be dialed.NOTE: This feature will not work for unavailable or private calls (denoted as Withheld in the Log).To Clear the Call Log1)  Press the MENU key.2)  Select Call Log, then select Clear Logs3)  A notification will appear to tell you that the Call Log has been cleared.To Check the Last Call Time1)  Press the MENU key,2)  Select Call Log, then Times & Costs.3)  Select Last Call Time.To Check Total Accumulated Air Time1)  Press the MENU key2)  Select Call Log, then Times & Costs.3)  Select All Calls Time.To Reset Accumulated Air Time1)  Press the MENU key2)  Select Call Log, then Times & Costs.3)  Select Clear Logs.To Turn On/Off the Keypad Tones1)  Press the MENU key.2)  Select Settings, then Audio Settings.3)  Select Keypad Tones.4)  Select On or Off.To Turn On/Off the Warning Tones1)  Press the MENU key.2)  Select Settings, then Audio Settings.3)  Select Warning Tones4)  Select On or Off.Phonecell®SX5D 19 Technical ManualView All CallsTotal Accumulated Air Time
Date and Time SettingsThe SX5D allows you to set the date, time, time zone, and time format (12 or 24 hour), and customize how that information is displayed.To Set the Date1)  Press the MENU key.2)  Select Clock, then Clock Settings.3)  Scroll to Date Format.The current format will display.4)  Press the CHANGE key.5)  Select the way you want to view the date. Options are Day:Month:Year, Month:Day:Year, orYear:Month:Day6)  Press OK, then press the BACK key to return to the Clockmenu.7)  Scroll to Set Date.8)  Press the CHANGE key.9)  Enter the desired date.10)  Press OK.To Set the Time1)  Press the Menu key.2)  Select Clock, then Clock Settings.3)  Scroll to Time Format.The current format will display4)  Press the CHANGE key.5)  Select the time format you wish to use (12 hour or 24 hour)6)  Press OK, then the BACK key to return to the Clock menu.7)  Select Set Time.8)  Enter the desired time.9)  Press OK.To Set the Time Zone1)  Press the Menu key.2)  Select Clock, then scroll to Set Time Zone.3)  Press the CHANGE key.Use the two middle soft keys to scroll left or right on the graphic to highlight the time zoneyou are in.4)  Press the far left soft key to select the highlighted time zone.Alarm SettingsYou can set the alarm time and tone, and you can set it for daily use or for one time only.To Set Alarm Time and Tone1)  Press the MENU key.2)  Select Clock, then Set Alarm.3)  Select Set time, then enter the desired alarm time.4)  Press OK.5)  Select Set Tone, then select the desired alarm tone.6)  Press OK.To Set Alarm to Repeat Every day1)  Press the MENU key.2)  Select Clock, then Set Alarm.3)  Select Repeat Daily.Phonecell®SX5D 20 Technical ManualSetting the DateSetting the Time
To Turn Alarm On/Off1)  Press the MENU key.2)  Select Clock, then Set alarm.3)  Select Alarm Status.4)  Select On or Off.5)  Press OKTo Display Your Own Telephone NumberYou can have your phone number display when the SX5D is turned on.1)  Press the MENU key,2)  Select Settings, then Phone Settings.3)  Select My number.4)  Press the EDIT key.5)  Enter your phone number.6)  Press OK.To Change Greeting MessageThe Greeting Messages displays when the SX5D is turned on.1)  Press the MENU key,2)  Select Settings, then Phone Settings.3)  Select Set greeting.4)  Enter the desired greeting message.5)  Press OK.To Change the Display Screen Contrast1)  Press the MENU key.2)  Select Settings, then Phone settings.3)  Select Screen contrast.4)  Use the arrow keys to adjust the display contrast.5)  Press OK.To Reset System DefaultsYou can reset all system features to the factory defaults. 1)  Press the MENU key 2)  Select Settings, then Restore Defaults.3)  Select Yes to restore all factory default settings.Phone Use RestrictionsYou can restrict the use of the phone by barring certain calls from being made or received. Youcan also create a Fixed Dialing list that will only allow numbers on that list to be dialed from yourphone.Handset Call BarsOutgoing Calls: Does not allow any calls to be made from the phone. Incoming Calls: Does not allow any incoming calls to be answered.Network Call BarsForeign Calls: Does not allow international calls.Only local and home country: Only allows local and home country calls.Incoming Calls: Does not allow any incoming calls.Incoming if abroad: Does not allow any incoming calls when outside the home country.Outgoing: Does not allow any calls to be made.All: Does not allow any calls to be made or received.Cancel all: Deactivates any network call bars that are currently active.Phonecell®SX5D 21 Technical Manual
To Set Call Bar Modes1)  Press the MENU key.2)  Select Settings, then Security settings.3)  Select Handset Call Barring, or Network Call Barring 4)  Select the bars you wish to implement.To Use Fixed Dialing1)  Press the MENU key.2)  Select Settings, then Security settings.3)  Select Fixed Dialing.4)  Select On.5)  Enter SIM PIN 2, then press OK.To Add to or Edit the Fixed Dialing List1)  Press the MENU key2)  Select Settings, then Security settings.3)  Select Fixed Dialing.4)  Select Edit dial list5)  To add a new entry, select Add, enter the new number, then press OK.To Edit an existing entry, move on to Step 6.6)  Use the arrow keys to highlight the entry you wish to edit.7)  Press the OPTIONS key.8)  Select Edit to change the entry.Select Delete to erase the entry.To Lock the PhoneYou can lock your phone to keep unauthorized persons from using it or accessing any informa-tion stored in it. When the phone is locked, no keypad buttons will function until the lock code isentered To receive incoming calls when your phone is locked, you must enter the lock codewhen the phone rings. Turning the phone off or inserting a new SIM Card does not disable thisfeature. The phone stays in lock mode until you unlock it.1)  Press the MENU key.2)  Select Settings, then Security settings.3)  Select Handset Lock PIN.4)  Select On.To Unlock the Phone1)  Press the MENU key.2)  Select Settings, then Security settings.3)  Select Handset Lock PIN.4)  Select Off.To Change the Lock Code The lock code is preset at the factory to “0000.” You can change the lock code to any 4-digitcode.1)  Press the MENU key.2)  Select Settings, then Security settings.3)  Select Handset Lock PIN.4)  Select Change PIN5)  Enter your new lock code.NOTE: The new lock code must be four numeric digits.Phonecell®SX5D 22 Technical Manual
SUPPLEMENTARY FEATURES (NETWORK DEPENDENT)Call ForwardingCall Forwarding allows you to forward your incoming calls toanother telephone number, even if your phone is turned off. Youcan specify the criteria for calls to be forwarded. Options are: allcalls, calls that come in when your line is busy, calls that are notanswered after a specified number of rings, or calls that come inwhen the SX5D is powered off or has lost the network signal (NotFound). You can also specify certain types of calls to forward,such as voice, data, fax, or text messages. Contact your serviceprovider to activate Call Forwarding.To Turn On Call Forwarding1)  Press the MENU key.2)  Scroll to and select Call Divert.3)  Select the criteria you wish to use for forwarding calls (AllCalls, When Busy, No Answer, Not Found).4)  Select On5)  To choose which types of calls to forward, select By Service 6)  Highlight the service you wish to forward, then press SELECT.The default is All Services.Call WaitingCall Waiting alerts you to a second incoming call while you are on the phone. To respond to CallWaiting, press the Flash key or the hook switch. Contact your service provider to activate CallWaiting.To Turn On Call Waiting1)  Press the MENU key.2)  Select Settings3)  Select Call Settings.4)  Select Call waiting.5)  Select On.Multiparty CallingMultiparty Calling allows you to connect a three-way conversation, or transfer a call. Contactyour service provider to activate Three-Way Calling.To Engage a Multiparty Call1)  While in a call, put the call on hold.2)  Dial a second call, then press the Flash button to connect it.3)  When the second call is answered, press the MENU key andselect Multiparty5)  Select the option you wish to use.Join All: Join the active call with the held multiparty call.Hold All: Place multiparty call on hold.Next: Display the next call party in a multiparty call.Transfer: Connects one call party to another call party and allows the user to leave the call.Exclude: Place the selected party of a multiparty call on holdPrivate: Hold a private call with one party in a multiparty call. Other parties are put on hold.I am busy: User defined user busy (UDUB) indicates BUSY to a waiting caller.End All: End active and held calls.NOTE: You will only see options available dependant on the status of the call or calls. Forexample, if you only have one other person in the call, you will only get the End All option, or ifyou have already joined all the calls, you will not see the Join All option.Phonecell®SX5D 23 Technical ManualCall Forwarding Step 4Call Forwarding Step 6Call Forwarding Step 2Multiparty call
Phonecell®SX5D 24 Technical ManualVoicemailWhen there are new voicemail messages, the VM key will blink and the envelop icon will dis-play. Contact your service provider to activate voicemail.How to Check Voicemail1)  Press the VM key.You will be connected to your voicemail system automatically.2)  Follow the the automated instructions.How to Turn Voicemail On/Off1)  Press the MENU key.2)  Select Messages, then select Voicemail.3)  Select Set Voicemail, then select On or Off.How to Change the Voicemail Alert TypeYou can choose to be alerted to new voicemail by audio indication or by SMS. The default set-ting is for audio indication. Use the following instructions to set the voicemail alert to SMS.1)  Press the MENU key.2)  Select Messages, then select Voicemail.3)  Select Voicemail Settings.4)  To be alerted by a SMS indication, select Alert by SMS.5)  From a different phone, call your number and leave a voicemail message.The network will send you an SMS indication that you have new voicemail.6)  View the SMS message you recieve from the network and write down the text.7)  Follow steps 1-3 above to return to Voicemail Settings.8)  Select Alert match.9)  Enter the text that you copied from the SMS message from the network.This text will display whenever you get a new voicemail message.NOTE: If you do not specify the Alert match text, or if you enter incorrect text for the Alertmatch, the SMS message will not display when you receive new voicemail.Short Message Service (SMS)SMS allows you to transmit and receive short text messages. If there are new messages thatyou have not checked, the message envelope icon will be displayed and the SMS key will blink.You can store up to ten text messages, each of which can be no more than 160 characters long.Contact your service provider to activate SMS.To use a keyboard to type messages, connect a keyboard to the keyboard port on the back ofthe SX5. You still must use the soft keys to navigate through the menus, but you can use thekeyboard to enter any text.How to View Text Messages1)  Press the SMS key.2)  Select Received Messages.3)  Scroll to the message you wish to view.4)  Press the READ key.NOTE: Unread messages are denoted by the closed envelopicon, and message that have been read are denoted by the openenvelop icon.Viewing MessagesNew Message Notification
To Reply to Received Messages1)  View the message you wish to reply to.2)  Press the OPTIONS key.3)  Select Text Reply to reply with a text message.Select Voice Reply to reply with a voicemail.4)  For a Text Reply, type your reply message, then press OK.Selecting Voice Reply will activate the speakerphone and con-nect to the person who sent the message.To Forward Text Messages1)  View the message you want to forward.2)  Press the OPTIONs key.3)  Select Forward.4)  Enter the number of the person you want to forward the mes-sage to, or press the NAME key to select a phonebook entry.5)  Press OK6)  Select Send Now.To Delete Text Messages1)  View the message you wish to delete.2)  Press the OPTIONS key.3)  Select DeleteTo Create Text Messages1)  Press the SMS key.2)  Select New Message.3)  Enter the message text.NOTE: Use the *key on the keypad to change the type of text you enter to all capital letters(ABC), lower case letters (abc), or numbers (123). The current text type is displayed under theclock in the upper right corner of the display screen.4)  Press OK.5)  Enter the number of the person you wish to send the messageto, or press the NAME key to select phonebook entry.6)  Press OK.7)  To send the message, select Send Now.To save it to send at a later time, select Send Later.To View Saved Messages1)  Press the SMS key.2)  Select Saved Messages.3)  Select the message you wish to view.To Send Saved Messages1)  Press the SMS key.2)  Select Saved Messages.3)  View the message you wish to send.4)  Press the OPTIONS key.5)  Select Forward.6)  Enter the number of the person you wish to send the message to or press the NAME key tosearch your phonebook.7)  Press OK8)  Select Send Now.Phonecell®SX5D 25 Technical ManualReceived Message OptionsCreating Text MessagesViewing Saved MessagesForwarding Text MessagesView Received Message
Info MessagesInfo messages provide you with information such as phone numbers for taxi services, carrentals, or emergency services. If your service provider offers Info messages, you can selectwhat subjects you would like to view and choose the language in which you would like to view it.To Set Info Subjects1)  Press the MENU key.2)  Select Messages, then select Info messages.3)  Select Settings, then select Subject.4)  Select Active.5)  Press the SELECT key.5)  Select Add.6)  From the list, select the subject you would like to view.To Set Languages1)  Press the MENU key.2)  Select Messages, then select Info messages.3)  Select Settings, the select Set languages.4)  From the list, select the language you would like to use.In-Call OptionsThe following options are available when you press the MENU key while in a call.Hold:  Puts active call on holdRetrieve: Activates a call that is on hold.Swap: Swaps between held call and active call.End & Next: Releases active call and answers waiting call.End Current: Ends the currently displayed callMultiparty: Displays options for managing multiparty calls.Main Menu: Allows access to the Phonebook, Messages, or Call Log features.NOTE: Some options display depending on the call status. For example, if you have don’t have anycalls on hold, you will not see the Retreive or Swap options.Phonecell®SX5D 26 Technical Manual
DIGITAL DATA SERVICEStandard Modem SettingThe SX5D features a DB-9 digital computer fax/data port for connection to a personal computer(PC) - not supplied. When connected to a PC, the SX5D’s PC interface is capable of sendingand receiving digital fax transmissions, sending and receiving e-mail communications, andbrowsing the Internet. (Data speeds may vary depending upon your cellular network.)PC Data ConnectionA data cable - not included -  is required for data transmission. To determine the necessary cable,count the number of PIN connections in the serial port of your PC (see below).  If there are 9 PINconnections in the PC serial port, a DB-9 (female) to DB-9 (male) cable is required.  If there are25 PIN connections in the PC serial port, a DB-25 (female) to DB-9 (male) cable is required - seeFigure - .For specific digital fax/data setup procedures, see Appendix A - How to Setup Your PC SerialPort for Phonecell®SX5 Digital Fax/Data.Sending and Receiving Digital FaxYour computer needs a standard 19,200 bps modem and a commercial PC fax emulator(Winfax, Netfax, etc.), To send a fax, no special settings are required. The computer will changethe SX5D mode setting automatically and reset it to voice mode after sending a fax. To receivea fax, you must change the SX5D from voice to fax mode.1)  Set up a standard 19,200 bps modem.2)  Install a commercial PC fax emulator (Winfax, Netfax, etc.).Phonecell®SX5D 27 Technical ManualTo PC Serial Port DB-9 cable and PC serialport have 9 PIN connectionsDB-25 (female) to DB-9 (male) CableDB-9 (female) to DB-9 (male) CableORDB-25 cable and PCserial port have 25PIN connections To DB-9 Data Port Figure  - PC Data Connection
LEAST COST ROUTING (LCR) SETUPThe personal LCR option for the SCX5D allows you to operate both a regular public switchedtelephone network (PSTN) landline phone account and a GSM wireless account through a sin-gle deskphone. This gives you two separate lines, and allows you to take advantage of lowercalling costs, depending on whether you are connecting to someone via a PSTN or a wirelessnetwork. You can also connect additional phones to the SX5D, but these will only operate overthe GSM network (they cannot access the PSTN). In order to make calls or receive calls overthe PSTN, you must use the SCX5D deskphone.How to Connect Your SX5 to the Landline PSTN1)  Connect the wall jack to the unmarked jack on the SX5.How to Connect Additional Phones to Your SX51)  Connect your additinal telephone to the jack on the SX5 that is marked with a telephoneicon.NOTE: Be sure to connect to the appropriate RJ-11 jacks, because improper connections couldcause damage your SX5.How to Set the LCR DefaultYou can set the SX5D to operate on either the PSTN or the GSM network when you pick up thehandset. You can then set a prefix to dial to access the other service. The factory default isGSM.1)  Press the MENU key.2)  Select Settings, then Extension Settings.3)  To set the system to operate over the PSTN when you pick up the phone, select Internal.To set the system to operate on the GSM wireless network, select External.4)  To set a prefix for accessing whichever system you did not select in Step 3, select Prefix.5)  Enter up to two digits for the prefix you wish to use. The factory default prefix is “#”.6)  Press OK.Phonecell®SX5D 28 Technical ManualConnect to PSTN Connect to additional phoneFigure -
ANALOG FAX SETUPThe Analog Fax option allows you to connect a fax machine and additional telephones to yourSX5. Your SX5D can be set up to use one or both of its RJ-11 jacks. In Single Jack mode, onlythe jack designated with a telephone icon is operational. You can connect a fax machine or anadditional telephone into that jack, but to receive faxes you must have fax machine connected.In Dual Jack mode, the unmarked jack is used for fax, and the jack marked with the telephoneicon is used for any additional phones.To Set Your SX5D for Analog Fax1)  Press the MENU key.2)  Select Settings, then select Fax Settings.3)  Select RJ-11.4)  Select the mode you wish to use (Single or Dual Jack). The default is Dual Jack.To Connect Your SX5D for Dual Jack Mode1)  Connect your fax machine to the unmarked phone jack on your SX5D.2)  Connect a regular phone to the phone jack that is marked with a telephone icon.To Connect Your SX5D for Single Jack Mode1)  Connect your fax machine to the phone jack on your SX5D that is marked with a telephoneicon.NOTE: You will have to enter the fax by-pass to send a fax when you are in single jack mode,because the SX5D default setting is for voice calls. To send a fax, dial “# *19 * 1 #” then dialthe number for where you are sending the fax. After the fax is sent, the SX5D will reset itself forvoice calls.To Set Your SX5D for Digital Fax1)  Press the MENU key.2)  Select Settings, then select Fax Settings.3)  Select Serial Port.NOTE: You must have your SX5D connected to a computer, or other device that is set up fordigital data, via the serial connector in order to send or receive digital faxes.Phonecell®SX5D 29 Technical ManualConnect to Fax machine Connect to regular phone This RJ-11 is not usableConnect to fax machine orregular phoneSingle Jack ModeDual Jack ModeFigure -  Figure -
Phonecell®SX5D 30 Technical ManualTECHNICIAN COMMANDSThe following options are to be used by trained field technicians to set up the Phonecell®SX5for operation in the network. To prevent casual access to these options, which can directly affectthe proper operation of the unit, they are protected by a Service PIN.To Access the Sevice menu, press the MENU key, then select Service. You will be prompted toenter the Service PIN before you can access any Service menu items. Each option is describedbelow, along with the available settings and the system defaults Service SettingsMobile Equipment Personalization (MEP) Locks: The five locks available are SIM, Network,Network Subset, Provider, and Corporate. With the correct password, you can activate, deactivate, disable, or check the status of any MEP lock. Once a lock is disabled, it cannot bereactivated.Dial Tone Type: The available options are 425 Hz and Dual Frequency (default).This dial tonewill be the air interface (GSM) dial tone presented to the user on the desk phone and any POTSphones connected to the SX5D.Audio In changes the input impedance. Options are 600 Ohms (default) or 900 Ohms.Supervision Pulse changes the pulse that is generated when the far end answers a call origi-nated from the SX5D. Options are 12 kHz (default), 16 kHz., Off, Pulse Duration, and PulseLevel.Pulse Duration options include any value between 10 and 65535 milliseconds.Pulse Level options listed by dB ranges (default is -3dB).Line Reversal enables line reversal on tip and ring for incoming calls.Line Reversal (MO) can be turned On or Off (default).Line Reversal (MT) can be turned On or Off (default).Line Ringing controls the line ringer.Frequency options are 20 Hz (default), 25 Hz, or 50Hz.Cadence options range from.1 to 25.5 seconds (by 100 millisecond increments).Diconnect Pulse  sets pulse value. Options range from 10 to 65535 milliseconds.Dial Tone After Disconnect determines if a dial tone is heard after far end disconnect. If On,then dial tone will start at some time after a far end disconnect is detected as long as the user isstill off hook (Off is default). Receiver Off Hook (ROH) Setup sets the parameters of the ROH tone that is heard when theSX5 goes off hook for an extended period of time without making a call. Options are Continuousor Non-continuous, Set Start Time, and Set Stop Time.Self Test Interval sets the reset interval for periodic resetting or sanity checking. The range is 0to 65536 minutes, where 0 means that there is no resetting.SERVICE PIN: Options are On (default) or Off, and Change PIN. When the Service PIN isentered wrong three consecutive times, you will be returned to the Main Menu.RF: Displays the quality and signal level of the received signal (for evaluation of SX5D place-ment, etc). The display will show a dB level for received signal strength and/or a decimal valuerepresenting the signal quality (BER, FER, etc.). The signal strength will be on row 2 and thesignal quality value will be on row 3.Restore Service DEFAULTS: Resets all service items to factory defaults separately from theuser settings.WARNING!The following commands may be used by a trained service technician to change the configuration of the Phonecell®SX5. WARNING: these commands are intendedfor use by trained service technicians only. Untrained users could damage thePhonecell®SX5, violate local regulations and breach the service agreement with the cellularprovider. For further assistance, please contact your Authorized Telular Representative.!
SAFETY INFORMATIONYour Phonecell®SX5 Desktop Phone functions as both a radio transmitter and receiver. When itis ON, the SX5D receives and sends out radio frequency (RF) energy. The GSM 800 unit oper-ates in the frequency range between 824 and 894 MHz, and the GSM 1900 between 1850 MHzand 1990 MHz. Both employ commonly used phase/frequency modulation techniques. Whenyou use your Phonecell®SX5, the cellular system handling your call controls the power level atwhich your unit transmits.Exposure to RF (Radio Frequency) EnergyIn 1991, the Institute of Electrical and Electronics Engineers (IEEE), and in 1992, the AmericanNational Standards Institute (ANSI), updated the 1982 ANSI Standard for safety levels withrespect to human exposure to RF energy. After reviewing the available body of research, morethan 120 scientists, engineers and physicians from universities, government health agenciesand industry developed this updated Standard. In March, 1993, the U.S. FederalCommunications Commission (FCC) proposed the adoption of this updated Standard.The design of your Telular Phonecell®SX5 complies with this updated Standard. Of course, ifyou want to limit RF exposure even further than the updated ANSI Standard, you may choose tocontrol the duration of your calls and operate your phone in the most power-efficient manner.Safe Operation RequirementThe Phonecell®SX5 must be either wall mounted or desk mounted and should not be operatedwhen any person is within 8 inches (20 centimeters) of the antenna.Temperature EnvironmentOperating Temperature: From -20°C to +60°C ; Up to 95% relative humidity (non-condens-ing).Storage Temperature: From -25°C to +75°C; Up to 95% relative humidity (non-condensing).Antenna Care and ReplacementDo not use the Phonecell®SX5 with a damaged antenna. If a damaged antenna comes intocontact with the skin, a minor burn may result. Have your antenna replaced by a qualified tech-nician immediately. Use only a manufacturer-approved antenna. Unauthorized antennas, modifi-cations, or attachments could damage the Phonecell®SX5.DrivingCheck the laws and regulations on the use of cellular products in the areas where you drive.Some jurisdictions prohibit your using a cellular device while driving a vehicle. Even if your juris-diction does not have such a law, we strongly suggest that, for safety reasons, the driver useextreme caution when operating the cellular device while the vehicle is in motion. Always obeythe law.Electronic DevicesMost modern electronic equipment is shielded from RF energy. However, RF energy from cellu-lar devices may affect inadequately shielded electronic equipment.RF energy may affect improperly installed or inadequately shielded electronic operating andentertainment systems in motor vehicles. Check with the manufacturer or its representative todetermine if these systems are adequately shielded from external RF energy. You should alsocheck with the manufacturer of any equipment that has been added to your vehicle.Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids,etc.) to determine if they are adequately shielded from external RF energy.Turn your Phonecell®SX5 OFF in health care facilities when any regulations posted in the areasinstruct you to do so. Hospitals or health care facilities may be using equipment that could besensitive to external RF energy.Phonecell®SX5D 31 Technical ManualIMPORTANT!To ensure safe and efficient operation, please read the following information and observethese guidelines whenever using your Phonecell®SX5.
AircraftTurn OFF your Phonecell®SX5 before boarding any aircraft.• Use it on the ground only with crew permission.• Do not use it in the air.To prevent possible interference with aircraft systems, U.S. Federal Aviation Administration(FAA) regulations require you to have permission from a crew member to use your cellularphone (or any other cellular product) while the plane is on the ground. To prevent interferencewith aircraft systems, FCC regulations prohibit using your cellular device while the plane is inthe air.ChildrenDo not allow children to play with your Phonecell®SX5 to prevent damage to the unit.Blasting AreasConstruction crews often use remote control RF devices to set off explosives. Therefore, toavoid interfering with blasting operations, turn your Phonecell®SX5 OFF when in a "blastingarea" or in areas posted: "Turn off two-way radio."Potentially Explosive AtmospheresTurn your Phonecell®SX5 OFF when in any area with a potentially explosive atmosphere. It israre, but your Phonecell®SX5 or its accessories could generate sparks. Sparks in such areascould cause an explosion or fire resulting in bodily injury or even death.Areas with a potentially explosive atmosphere are often, but not always, clearly marked. Theyinclude fueling areas such as gas stations; below deck on boats; fuel or chemical transfer orstorage facilities; areas where the air contains chemicals or particles, such as grain, dust, ormetal powders; and any other area where you would normally be advised to turn off your vehicleengine.Do not transport or store flammable gas, liquid or explosives in the area of your Phonecell®SX5or accessories.Vehicles using liquefied petroleum gas (such as propane or butane) must comply with theNational Fire Protection Standard (FPA-58).  For a copy of this standard, contact the NationalFire Protection Association, One Batterymarch Park, Quincy, MA 02269, Attn:  PublicationsSales Division.FCC Part 15 Class B ComplianceThis Phonecell®SX5 model has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide rea-sonable protection against harmful interference in a residential installation. This equipment gen-erates, uses and can radiate radio frequency energy and, if not installed and used in accor-dance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined byturning the equipment OFF and ON, the user is encouraged to try to correct the interference byone or more of the following measures:Reorient or relocate the antenna.Increase the separation between the equipment and the terminal.Connect the equipment into an outlet on a circuit different from that to which the terminalis connected.Consult your Authorized Telular Distributor or an experienced radio/TV technician for help.Phonecell®SX5D 32 Technical ManualWARNING!Your Phonecell®SX5 is intended either to be wall mounted or desk mountedon a flat suface to allow proper ventilation. Do not block the space beneathyour Phonecell®  SX5 as this could cause the unit to overheat and fail.!
IMPORTANT NOTICESWarrantyI.  WHAT THIS WARRANTY COVERS AND FOR HOW LONG:TELULAR CORPORATION ('Telular") warrants to a distributor Buyer, or to a customer only if thecustomer is a Buyer directly from Telular, that the Products (including accessories) shall complywith the applicable Specifications and shall be free from defects in material and workmanshipunder normal use and service for a period of fifteen (15) months from date of shipment fromTelular.  Telular, at its option, shall at no charge either repair, replace or refund the purchaseprice of the Product during the warranty period, provided it is returned by Buyer in accordancewith the terms of this warranty to the Telular designated repair center. Repair or replacement, atTelular's option, may include the replacement of parts, boards or Products with functionallyequivalent reconditioned items. Repaired and replacement items are warranted for the balanceof the original warranty period. All replaced items shall become the property of Telular. SUCHACTION ON THE PART OF TELULAR SHALL BE THE FULL EXTENT OF TELULAR'S LIA-BILITY HEREUNDER, AND BUYERS EXCLUSIVE REMEDY. Buyer shall be responsible for allcosts and expenses incurred by Buyer including without limitation any handling, labor or trans-portation charges. OTHER THAN AFORESAID, THIS EXPRESS WARRANTY IS EXTENDEDBY TELULAR TO BUYER ONLY AND NOT TO BUYER'S CUSTOMERS OR USERS OFBUYER'S PRODUCTS.II.  HOW TO OBTAIN WARRANTY SERVICEProduct covered under this warranty shall only be accepted from and returned to Buyer's desig-nated repair center. Buyer's dealers, distributors, agents, and end users cannot submit items toTelular under this warranty. To receive warranty service an RMA number must first be obtainedfrom Telular Technical Support. The defective or non-compliant Product should be sent by Buyerfreight pre-paid to: Telular Corporation, 647 North Lakeview Parkway, Vernon Hills, IL 60061,USA or other designated location.  The product must be packaged in the original carton andpacking material or an equivalent package and must have the assigned RMA number clearlymarked on the carton. Returned Product received without an RMA number will be returned tothe sender.III.  WARRANTY CONDITIONS:This is the complete warranty for the Products manufactured by Telular and sold to Buyer.Telular assumes no obligation or liability for additions or modifications to this warranty unlessmade in writing and signed by an officer of Telular. Unless made in separate written agreementbetween Telular and Buyer, Telular does not warrant the installation, field maintenance or serv-ice of the Products or parts.TELULAR CANNOT BE RESPONSIBLE IN ANY WAY FOR ANY ANCILLARY EQUIPMENTNOT FURNISHED BY TELULAR WHICH IS ATTACHED TO OR USED IN CONNECTIONWITH THE PRODUCTS OR FOR OPERATION OF THE PRODUCTS WITH ANY ANCILLARYEQUIPMENT AND ALL SUCH EQUIPMENT IS EXPRESSLY EXCLUDED FROM THIS WAR-RANTY. FURTHERMORE, TELULAR CANNOT BE RESPONSIBLE FOR ANY DAMAGE TOTHE PRODUCTS RESULTING FROM THE USE OF ANCILLARY EQUIPMENT NOT FUR-NISHED BY TELULAR FOR USE WITH THE PRODUCTS.WHEN THE PRODUCT IS USED IN CONJUNCTION WITH ANCILLARY OR PERIPHERALEQUIPMENT NOT MANUFACTURED BY TELULAR, TELULAR DOES NOT WARRANT THEOPERATION OF THE PRODUCT/PERIPHERAL COMBINATION, AND TELULAR SHALLHONOR NO WARRANTY CLAIM WHERE THE PRODUCT IS USED IN SUCH A COMBINA-TION AND IT IS DETERMINED BY TELULAR THAT THERE IS NO FAULT WITH THE PROD-UCT. TELULAR DISCLAIMS LIABILITY FOR RANGE, COVERAGE, AVAILABILITY, OROPERATION OF THE CELLULAR SYSTEM WHICH IS PROVIDED BY THE CARRIER.Phonecell®SX5D 33 Technical Manual
Phonecell®SX5D 34 Technical ManualIV.  WHAT THIS WARRANTY DOES NOT COVER:(a) Subsequent upgrades and enhancements to the Product. (b) Defects, non-compliance ordamage resulting from use of the Product in other than its normal and customary manner orenvironment. (c) Defects, noncompliance or damage from misuse, lightening, accident or neg-lect. (d) Defects, noncompliance or damage from improper testing, operation, maintenance,installation, adjustment, or any alteration or modification of any kind. (e) Product disassembledor repaired in such a manner as to adversely affect performance or prevent adequate inspectionand testing to verify any warranty claim. (f) Product which has had the serial number removedor made illegible. (g) Defects, non-compliance or damage due to spills of food or liquid. (h) Allplastic surfaces and all other externally exposed parts that are scratched or damaged due tocustomer normal use. (i) Costs and expenses, including without limitation handling, labor andtransportation, incurred in returning Product for warranty service to Telular's Repair Center. (j)Repair, programming or servicing by someone other than Telular.V.  GENERAL PROVISIONS:THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS OR STATUTORY WAR-RANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WAR-RANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE,INFRINGEMENT, DELIVERY, NEGLIGENCE AND PERSONAL INJURY, ARE DISCLAIMED.FURTHER, AS THE CELLULAR CARRIER IS NOT CONTROLLED BY TELULAR, NO WAR-RANTY IS MADE AS TO COVERAGE, AVAILABILITY OR GRADE OF SERVICE PROVIDEDBY THE CELLULAR CARRIER. IN NO EVENT SHALL TELULAR BE LIABLE FOR DAM-AGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OFUSE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAV-INGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUTOF THE USE OR INABILITY TO USE SUCH PRODUCT TO THE FULL EXTENT SUCH MAYBE DISCLAIMED BY LAW. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION ORLIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOWLONG AN IMPLIED WARRANTY LASTS.VI.  SOFTWARE PROVISIONS:Laws in the United States and other countries preserve for Telular certain exclusive rights forcopyrighted Telular software such as the exclusive rights to reproduce in copies and distributecopies of such Telular software. Telular software may be copied into, used in and redistributedwith only the Product associated with such Telular software. No other use, including without limi -tation, disassembly of such Telular software or exercise of exclusive rights in such Telular soft-ware is permitted and Telular reserves all rights not expressly granted in this LimitedCommercial Warranty.Patents:Telular Corporation products are protected and manufactured under one or more of the followingU.S. patents and related international patents and patents pending relating thereto: 4,658,096;4,737,975; 4,775,997; 4,868,519; 4,922,517; 5,134,651; 5,361,297; 5,469,494; 5,046,085;5,715,296.Trademarks:Telular Corporation owns the following registered trademarks: TELULAR and design, TELULAR,CELJACK, MAXJACK, TELCEL, HEXAGON LOGO, PHONECELL, CELSERV, TELGUARD,CPX, and AXCELL.
APPENDIX A: TO SETUP PC SERIAL PORTS FOR PHONECELL DIGITAL FAX/DATARequirements· GSM account with your network service provider including a Data/Fax facility.· PC/Laptop/ Notebook with Com Port.· Windows 95/98NOTE: When all of the above have been satisfied, you may proceed.Modem Setup1)  Power on your PC/laptop and start Windows 95/98.2)  Using the PC pointing device, press the "START" button, select "SETTINGS" and then"CONTROL PANEL". Once the Control Panel window appears double click the MODEMSicon button. The modem properties window will appear. NOTE: A data card modem device may appear in the list of installed modems.3)  Click the ADD button to install a new modem device for the Phonecell®SX5.Phonecell®SX5D 35 Technical Manual
4)  The install new modem window may appear asking for the type of modem to install. Click on"Other" followed by clicking the NEXT button. If this window does not appear, go to Step 5.5)  The install new modem window will appear. Then, click on the "Don't detect my modemoption" followed by clicking the NEXT button.Phonecell®SX5D 36 Technical Manual
6)  The install new modem will update again to select the manufacturer and modem model.Click on "Standard Modem Types" from the manufactures list followed by "Standard 19200bps Modem" from the model list. Then click on the NEXT button.7)  The install new modem will update to select the com port.  Click on the available serial portand then click on the "Next" button. Windows 95 will create a modem configuration file forthe Phonecell®SX5. This may take several minutes.Phonecell®SX5D 37 Technical Manual
8)  The Install New Modem window will update again. Click on Finish to proceed. 9)  The Modems Properties window should appear. Click on the Properties button.Phonecell®SX5D 38 Technical Manual
10)  The Standard 19200 bps Modem Properties window will open in the General tab. Set asshown with the com port you have selected. 11)  Click on the Connection tab. Set as shown below. Phonecell®SX5D 39 Technical Manual
©2002 Telular Corporation, all rights reserved. Part Number 56023201647 North Lakeview ParkwayVernon Hills, Illinois 60061, USATel:847-247-9400 • Fax: 847-247-0021E-mail: mainoffice@telular.comhttp://www.telular.com12)  Click on the Advanced button. Set as shown. 13)  Click on OK and Close to back out of each window. Your modem is now set up.

Navigation menu