Telular GSMUSDUAL PhoneCell SX5 User Manual 56029701 SX5D GSM 850

Telular Corporation PhoneCell SX5 56029701 SX5D GSM 850

Contents

SX5D User Manual

7/28/03 Part Number 56029701PHONECELL®SX5D GSM• Fixed Wireless Phone• Fixed Wireless Fax Phone• Fixed Wireless LCR Phone850/1900 MHZGSM (DUAL BAND)USER MANUAL
Phonecell®SX5D GSM i User ManualQUICK CONNECTION GUIDEFixed Wireless PhoneFixed Wireless FAX Phone
Phonecell®SX5D GSM ii User ManualFixed Wireless Personal Least Cost Routing (LCR) Phone
Phonecell®SX5D GSM iii User ManualSX5D MENU STRUCTUREPhonebookView NamesAdd NameSettingsMessagesReceived MessagesSaved MessagesCreate MessageMessage SettingsVoicemailInfo MessageClockSet AlarmClock SettingsSet TimeSet DateSet Time ZoneSettingsPhone SettingsAudio SettingsCall SettingsData SettingsFax Settings*Extension Settings*Dial SettingsNetwork SettingsSecurity SettingsRestore DefaultsService Settings**Call LogAll CallsMissed CallsReceived CallsDialed NumbersClear LogsCall TimeGPRS InfoCall DivertAll CallsWhen BusyNo AnswerNot FoundCancel All Diverts* Not available on all models** Requires passwordMenu
Phonecell®SX5D GSM iv User ManualBefore installing your Phonecell®SX5D, carefully remove the contents from the shipping cartonand check for evidence of shipping damage. If damage is found, contact your AuthorizedTelular Distributor or shipping agent immediately.SAFE OPERATION INSTRUCTIONSIMPORTANT! Before installing or operating this product, read the SAFETY INFORMATIONsection of this manual.•• Install unit indoors.•• Install unit on hard, flat surface for proper ventilation.•• Do not expose unit to rain or moisture.••Do not place unit on or close to sources of heatIMPORTANT NOTICESTERMS AND CONDITIONS FOR USE OF PHONECELL®PRODUCTS ("Product")These Terms and Conditions are a legal contract between you and Telular Corporation for the title to and use of the Product.BY RETAINING AND USING THE PRODUCT AFTER RECEIPT OF IT, YOU AGREE TO THE TERMS AND CONDITIONSINCLUDING WARRANTY DISCLAIMERS, LIMITATIONS OF LIABILITY AND INDEMNIFICATION PROVISIONS BELOW. IFYOU DO NOT AGREE TO THE TERMS AND CONDITIONS, DO NOT USE THE PRODUCT AND IMMEDIATELY RETURNTHE UNUSED PRODUCT FOR A COMPLETE REFUND. You agree to accept sole responsibility for any misuse of the Productby you; and, in addition, any negligent or illegal act or omission of your or your agents, contractors, servants, employees, orother users of the Product so long as the Product was obtained from you, in the use and operation of the Product.INDEMNIFICATION OF TELULAR CORPORATION ("TELULAR")YOU SHALL INDEMNIFY, DEFEND AND HOLD HARMLESS TELULAR FOR ANY OF THE COST, INCLUDING REASON-ABLE ATTORNEYS' FEES, AND FROM CLAIMS ARISING OUT OF YOU, YOUR CLIENTS' OR OTHER THIRD PARTIES'USE OR OPERATION OF THE PRODUCT: (i) FOR MISUSE OR IN A MANNER NOT CONTEMPLATED BY YOU ANDTELULAR OR INCONSISTENT WITH THE PROVISIONS OF THIS MANUAL; (ii) IN AN ILLEGAL MANNER OR AGAINSTPUBLIC POLICY; (iii) IN A MANNER SPECIFICALLY UNAUTHORIZED IN THIS MANUAL; (iv) IN A MANNER HARMFULOR DANGEROUS TO THIRD PARTIES; (v) FROM CLAIMS BY ANYONE RESPECTING PROBLEMS, ERRORS OR MIS-TAKES OF THE PRODUCT; OR (vi) COMBINATION OF THE PRODUCT WITH MATERIAL, MODIFICATION OF THEPRODUCT OR USE OF THE PRODUCT IN AN ENVIRONMENT NOT PROVIDED, OR PERMITTED, BY TELULAR IN WRIT-ING. THE PARTIES SHALL GIVE EACH OTHER PROMPT NOTICE OF ANY SUCH COST OR CLAIMS AND COOPER-ATE, EACH WITH THE OTHER, TO EFFECTUATE THIS INDEMNIFICATION, DEFENSE AND HOLD HARMLESS.TELULAR CORPORATIONCorporate Headquarters647 North Lakeview ParkwayVernon Hills, Illinois 60061, USATechnical SupportTel: 847-247-9400 • Fax: 847-247-0021E-mail: support@telular.com • http://www.telular.comPower SupplyPhonecell®SX5D GSM Desktop Phone Spike AntennaPLEASE SEE THE IMPORTANT NOTICES SECTION OF THIS MANUAL FOR IMPORTANT INFORMATION ON USE, WARRANTY AND INDEMNIFICATIONCONTENTSAC Power CordPart Number 56029801 ©2003 Telular Corporation, All Rights Reserved
Phonecell®SX5D GSM v User ManualTABLE OF CONTENTSQuick Connection Guide..................................................................................................iSX5D Menu Structure ....................................................................................................iiiContents.........................................................................................................................ivSafe Operation Instructions ...........................................................................................ivImportant Notices...........................................................................................................ivSX5D Setup....................................................................................................................1SIM Card Installation .................................................................................................1Emergency Batteries .................................................................................................1Location and Setup....................................................................................................2Connect the Handset .................................................................................................2Desk-Mounting...........................................................................................................3Wall-Mounting ............................................................................................................4Connect the SX5D to AC Power................................................................................5Getting to Know Your SX5D ...........................................................................................6Function Keys ............................................................................................................6LCD Screen Icons......................................................................................................7Hearing Aid Compatibility...........................................................................................7Service Indication ......................................................................................................7Call Functions.................................................................................................................8Making Calls ..............................................................................................................8Receiving Calls ..........................................................................................................8Ending Calls...............................................................................................................8In-Call Functions........................................................................................................8SX5D Basic Features .....................................................................................................9Date and Time Settings .............................................................................................9Audio Settings............................................................................................................9Speakerphone..........................................................................................................10Phonebook...............................................................................................................10Speed Dialing...........................................................................................................12Change the Display Screen Contrast ......................................................................12SX5D Additional Features ............................................................................................13Call Logs..................................................................................................................13Alarm Settings..........................................................................................................13Language Selection .................................................................................................14Keyboard Setup .......................................................................................................14Personalization Options............................................................................................14Call Settings.............................................................................................................15Dial Settings.............................................................................................................15Network Settings......................................................................................................16SIM PIN Setup .........................................................................................................17Handset Call Barring................................................................................................18Restricted Dialing.....................................................................................................19Deskphone Lock ......................................................................................................20Closed User Groups (CUG).....................................................................................20Restore Factory Defaults .........................................................................................20
Phonecell®SX5D GSM vi User ManualSupplementary Services (Network Dependent) ...........................................................21In-Call Options .........................................................................................................21Call Divert (Forwarding)...........................................................................................22Call Waiting..............................................................................................................22Multiparty Calling .....................................................................................................22Caller ID Settings.....................................................................................................22Blocking Your Number (CLIR) .................................................................................22Voicemail..................................................................................................................23Short Message Service (SMS) ................................................................................23Information Messages .............................................................................................25Network Call Barring................................................................................................26Data Features...............................................................................................................27Connect SX5D to a Computer .................................................................................27Configure PC for Circuit Switched Data ..................................................................27Automatic Baud Rate Fall Back Control ..................................................................27GPRS (Packet Data) Connections...........................................................................28Analog Modem Support ...........................................................................................28SX5D Fixed Wireless LCR Phone................................................................................31Connect the SX5D Personal LCR Phone to the Landline (PSTN)..........................31Change Default Service...........................................................................................31Change PSTN Alert Setup.......................................................................................32Connect Additional Phones to the SX5D Personal LCR Phone..............................31SX5D Fixed Wireless FAX Phone ................................................................................32Fax Timing Adjustments...........................................................................................32Dual Jack Setup.......................................................................................................33Digital Fax Setup .....................................................................................................33Single Jack Setup ....................................................................................................34Routing Faxes to the Serial Port .............................................................................34SX5D Troubleshooting..................................................................................................35Conformance Statements .............................................................................................36Safety Information ........................................................................................................36Warranty .......................................................................................................................38Appendix A ...................................................................................................................41
Phonecell®SX5D GSM 1User ManualSX5D SETUPSIM Card InstallationThe SX5D requires a Subscriber Identification Module (SIM) for normal operation. The serviceprovider supplies the SIM card, which carries the account information needed to operate theSX5D. The SIM compartment is on the back of the SX5D.NOTE: If you don’t have a SIM card, contact your network service provider.1. Remove the power supply if it has already been connected. The power supply must beremoved whenever a SIM Card is removed or installed.2. Remove the SIM compartment cover by removing the screw - see Figure 1.3. Open the SIM compartment holder.4. Line up the SIM card with the arrow on the SIM card holder - see Figure 2.5. Gently insert the SIM card in the slot of the SIM card holder.6. Close the SIM card holder.NOTE: Do not force the SIM card holder shut. Make sure the SIM card is aligned properlywith the directional arrow on the holder.7. Reattach the SIM compartment cover with the screw.Emergency BatteriesInstall Batteries1. Remove the battery access door screw located on the bottom of the unit - see Figure 3.2. Press the battery access door tabs and remove the battery access door.3. Install 4 “AA” alkaline batteries (not supplied).4. Reinstall the battery access door using the screw - see Figure 4.SIM Compartment CoverSIM CardHolder SIM CardFigure 1 - SIM compartment cover.Cover ScrewFigure 3 – Battery access door.Battery AccessDoor ScrewBattery Access Door TabsBattery AccessDoor4 AA BatteriesFigure 4 - Battery installation.Figure 2 - SIM card installation.WARNING!Only “AA” alkaline batteries are to be used with the Phonecell®SX5. Use of any other batteries may result in fire and/or other damage to the unit.!
Phonecell®SX5D GSM 2User ManualBattery OperationThe unit will not automatically switch from AC to battery upon loss of AC power. The AC/Batteryswitch must be changed manually to the battery position - see Figure 5. Battery power will pro-vide up to 1 hour of talk time and 48 hours of standby.Location and SetupThe SX5D comes with a standard spike antenna (TNC).1. Attach and finger-tighten the antenna - see Figure 6. Do not over-tighten the antenna.2. Select a location that is above ground and as close to windows (or exterior walls) as possibleto get the best signal - see Figure 7.Connect the HandsetBefore you can use the SX5D, you must connect the handset cable. 1. Connect the handset cable to the phone jack - see Figure 8.2. Connect the handset cable to the handset - see Figure 8.Phone jackHandset cableFigure 6 - Attach the antenna. Figure 7 - SX5D location.HandsetAC/Battery SwitchBattery PositionAC PositionFigure 5 – AC battery Switch.Figure 8 – SX5D handset connection.
Phonecell®SX5D GSM 3User ManualDesk-MountingA wedge is included with the SX5D to be used to position the SX5D for easier viewing of theLCD screen and keypad. Attaching the wedge is optional. To attach the wedge, use the following instructions.1. Slide the wedge tabs on the thin end of the wedge into the bottom tab slots on the SX5D -see Figure 9.NOTE: Holding the wedge at an angle makes it easier to slide the wedge tabs into the bottomtab slots.2. Snap the wedge tabs on the thick end of the wedge into the top tab slots - see Figure 10.NOTE: The wedge will fit snugly, so it may be necessary to press the thick end of the wedgetowards the bottom tab slots (if the wedge tabs at the thin end have been inserted) in order tosnap it into the top tab slots.Top tab slotsBottom tab slotsWedge tabsWedge tabsAttach thick end of wedge at top of the SX5D.Figure 9 - Tab slots and wedge tabs.Figure 10 - Wedge attached for desk-mounting.
Phonecell®SX5D GSM 4User ManualWall-Mounting1. Remove the mounting clip from the cradle and re-insert it with the tab pointing up - seeFigures 11 and 12.2. Slide the wedge tabs on the thin end of the wedge into the bottom tab slots on the SX5D -see Figure 13. NOTE: Holding the wedge at an angle makes it easier to slide the wedge tabs into the bottomtab slots.3. Snap the wedge tabs on the thick end ofthe wedge into the top tab slots - seeFigure 14. The wedge will fit snugly, so itmay be necessary to press the thick endof the wedge towards the bottom tab slots(if the wedge tabs at the thin end havebeen inserted) in order to snap it into thetop tab slots.InsertMountingClip intothe Cradle(tab up)Mounting Clip inCradle (tab up)Figure 12 – Handset mounting clip for wall-mount.RemoveMounting Clipfrom the Cradle(tab down)Figure 11 – Handset mounting clip assembly.Attach thick end ofwedge at bottom of the SX5D.Figure 14 - Wedge attached for wall-mounting.Top tab slotsBottom tab slotsWedge tabsWedge tabsFigure 13 - Tab slots and wedge tabs.
Phonecell®SX5D GSM 5User Manual4. Mark two hole locations 83 mm (3-1/4 inches) vertically apart and drill two holes into the wall.5. Install the screws (not supplied) into the wall, leaving a gap of approximately 3 mm (1/8 inches) between the screw head and the wall.6. Align the mounting holes with the screws and mount the SX5D onto the screws - see Figures15 and 16.Connect the SX5D to AC Power1. A protective earth (safety ground) terminal screw marked with a protective earth symbol is pro-vided on the back of the SX5e - see Figure 17. Connect this terminal to a good earth ground(i.e., a cold water pipe) by means of an 18 gauge or heavier insulated wire. The wire insulationshould be green with a yellow stripe to indicate that this is a protective earth (safety ground)connection.2 Connect the barrel connector of the power supply to the AC power input on the rear panel ofthe SX5D - see Figure 17.3. Plug the AC power cord into the power supply.4. Turn the AC/Battery switch to the AC position.5. Plug the AC power cord into the wall socket. The SX5D will power up automatically.6. Check the cellular signal strength and move the unit until the best signal possible is achieved - see the Service Indication section of this manual.Figure 17 – SX5D AC power connection.AC Power CordWall SocketPower SupplyAC PowerInput BarrelConnectorFigure 16 – Mount the SX5D onto the screws.83 mm (3-1/4 inches)Figure 15 – SX5D mounting hooks.MountingHolesAC/Battery SwitchProtective EarthTerminal ScrewProtective EarthSymbol
Phonecell®SX5D GSM 6User ManualGETTING TO KNOW YOUR SX5DFunction KeysOperation of the SX5D is accomplished through the function keys on the keypad of the unit - seeFigure 18.Figure 18 – SX5D keypad and function keys.LCD Screen - Displays icons, information, and menu options necessary to operate the SX5D.LCD Soft Keys - Provide access to the SX5D menu options and features.Mute - Prevents the party on theother end of a call from hearing anysound from the SX5D.Volume - Controls the speaker volume level for the handset andthe speakerphone when the SX5Dis off-hook.Redial - Dials the last numbercalled from the SX5D.Flash - Allows answering of callwaiting, connecting multiparty calls,and putting an active call on hold tomake another call. Also can beused to skip Dial Delay time (quickdial).Speakerphone - Engages thespeakerphone feature.LED - Indicates power on, hookstatus, call alert, and call on hold.
Phonecell®SX5D GSM 7User ManualLCD Screen IconsIcons displayed on the LCD screen indicate the features in use, the status of the phone, signalstrength and battery status - see Figure 19.Hearing Aid CompatibilityThe SX5D model family has been tested to comply with part 68.316 of the FCC rules and regula-tions defining Hearing Aid Compatibility (HAC) and thus can be used with hearing aids.Service IndicationFull ServiceWhen powered on, the SX5D will display the Telular logo and theLED will light up. After a few seconds, the greeting and mobilecarrier will display. If service is available, the antenna icon willdisplay indicator bars. The number and height of the indicatorbars increases as the signal grows stronger (the more bars, thebetter the signal).No ServiceWhen no service is available, the antenna icon will not displayindicator lines. Contact your service provider to verify cellularservice is activated. No calls can be made in this condition.Limited ServiceIf there is a signal, but full service with the system is blocked, only emergency calls will beallowed. Contact your service provider for more information.Network RegistrationIf the home network is unavailable, but there is another network available (either another fre-quency or system), the SX5D will attempt to register to that system. If there is more than onesystem, a list of available systems will display. 1. Use the arrow keys to highlight a network from the list.2. Press the SELECT key. If the selected network cannot be accessed, the list of available net-works will be updated and a different network must be selected.No Service.Full Service.Figure 19 – SX5D LCD screen icons.Received SignalStrength - Indicates thestrength of the currentsignal. The more bars,the stronger the signal.Message - Displays when a new text or voicemail message has been received.Speaker - Indicates speakerphone is activated.Battery - Indicates the level ofbattery power. The more bars,the more power.Clock - Displays thecurrent time.LCD Soft Key Labels - Provide access to features withinthe sub-menus of the SX5D. Labels change according tothe selected sub-menu.Alarm - Indicates thatthe alarm feature hasbeen set.Call - Indicates that the hand-set is off-hook.
CALL FUNCTIONSMaking Calls1. Pick up the handset or press the SPEAKERPHONE key. The SX5D is now “off-hook.”2. Listen for dial tone.3. Dial the phone number. The dialed number will be displayed.The name will also be displayed if it is stored in the phonebook.Correct Dialing Errors• To erase one digit, press the CLEAR key once.• To erase all digits, press and hold down the CLEAR key untilall digits are erased.• To insert numbers, use the arrow keys.Redial the Last Telephone Number Dialed1. Pick up the handset or press the SPEAKERPHONE key. The SX5D is now “off-hook.”2. Press the REDIAL key.Receiving CallsWhen there is an incoming call, the SX5D rings, an incoming call notification displays the call type and Caller ID information (if available), and the LED blinks.1. Pick up the handset or press the SPEAKERPHONE key.2. Begin talking.NOTE: Press the REJECT key to refuse the call. The phone will stop ringing and the calling party will be disconnected.Receive a Call When Caller ID is ActivatedThe Caller ID feature displays the caller’s number when theSX5D rings. If the caller’s name and number are stored togetherin the SX5D phonebook, the caller’s name and number will bedisplayed. Contact your service provider to activate this feature.NOTE: If there are missed calls (calls not answered), “MISSEDCALLS” will be displayed with the number of calls missed. See the Call Logs section of this manual for more information.Ending CallsHang up the phone by either placing the handset back onto the SX5D cradle or press the SPEAKERPHONE key if using the speakerphone.In-Call FunctionsMute a Call1. While in a call, press the MUTE key. A notification will displayin the upper right corner of the LCD screen.2. Press the MUTE key again to un-mute the microphone.Place a Call on Hold1. While in a call, press the MENU key.2. Select Hold. The display will change from Active to Held.3. To reactivate the call, press the MENU key, then selectRetrieve.Adjust Volume1. While in a call, press the Volume keys to raise or lower thehandset/speakerphone volume.Phonecell®SX5D GSM 8User ManualMute a Call.Place a Call on Hold.Receive a Call When CallerID is Activated.Adjust Volume.Making Calls.
SX5D BASIC FEATURESDate and Time SettingsThe SX5D allows customization of the date, time, time zone, and time format (12 or 24 hour).Set the Date1. Press the MENU key.2. Select Clock.3. Scroll to Set Date, then press the CHANGE key.4. Enter the desired date.5. Press the OK key.Change the Date Format1. Press the MENU key.2. Select Clock, then select Clock Settings.3. Scroll to Date Format. The current format will display.4. Press the CHANGE key.5. Select the desired date format.6. Press the OK key.Set the Time1. Press the MENU key.2. Select Clock.3. Select Set Time.4. Enter the desired time.5. Press the OK key.Change the Time Format1. Press the MENU key.2. Select Clock, then select Clock Settings.3. Scroll to Time Format. The current format will display.4. Press the CHANGE key.5. Select the desired time format (12 hour or 24 hour).6. Press the OK key.Set the Time Zone1. Press the MENU key.2. Select Clock, then scroll to Set Time Zone.3. Press the CHANGE key. Use the two middle soft keys to scroll left or right on the graphic to highlight the time zone you are in.4. Press the far left soft key to select the highlighted time zone.Audio SettingsAdjust Alert Volume (Ringer)1. Press the MENU key.2. Select Settings, then select Audio Settings.3. Select Alert Volume, then set the desired volume level using the arrow keys.Phonecell®SX5D GSM 9User ManualEnter date (D/M/Y)Set the Time.Adjust Alert Volume.Change the Date Format.Set the Time Format.Arrowkeys
Adjust Alert Tones (Ringer)Alert tones can be customized for different types of calls, such as voice or text.1. Press the MENU key.2. Select Settings, then select Audio Settings.3. Use the arrow keys to scroll through the alert types.4. Select the desired alert sound.NOTE: If No Alert is selected, no alert will sound.Turn On/Off the Keypad Tones1. Press the MENU key.2. Select Settings, then select Audio Settings.3. Select Keypad Tones.4. Select On or Off.Turn On/Off the Warning Tones1. Press the MENU key.2. Select Settings, then select Audio Settings.3. Select Warning Tones.4. Select On or Off.Speakerphone1. Press the SPEAKERPHONE key. A dial tone will be heard through the speaker and the Speaker icon will display.2. Enter a telephone number, press the REDIAL key or press theNAME key to find a number you have previously entered intothe Phonebook - see the Phonebook section of this manual fordetails about how to enter a number.Speakerphone Microphone AdjustmentYou can adjust the microphone gain of the speakerphone from -5 to +5 using Spkr Phone Adj inthe Audio Settings menu.1. Press the MENU key.2. Select Settings then Audio Settings.3. Select Spkr Phone Adj then the desired microphone gain using the arrow keys.PhonebookThe SX5D has an Internal Phonebook capable of storing up to 250 telephone numbers with cor-responding names in the SIM card (SIM cards may have different memory capacities) and 18 inthe phone memory. HINT: To dial a number from the Phonebook when off hook, press the NAME key, select thename, then press the DIAL key.NOTE: The Phonebook will not be accessible while the SIM Card is read when the SX5D ispowered on. This process takes approximately 60 seconds.Adjust Phonebook SettingsEntries can be saved to the SIM card or to the phone memory. When numbers are saved to theSIM card, they can be transferred by removing the SIM card and installing it in another GSM phone.1. Press the MENU key.2. Select Phonebook, then select Settings.3. Select Save Entries To.4. Select the desired location of the phonebook entries.Phonecell®SX5D GSM 10 User ManualSpeakerphone off-hook.Adjust Phonebook Settings.Adjust Alert Tones.Turn On/Off the KeypadTones.
Keypad Buttons for Text Entry (Multitap)There are three or four letters assigned to each number on the telephone keypad. The letterson the keypad will display when pressed. For example, if the number 3 is pressed, a “D” willappear. If it is pressed twice, the “E” will appear, and if it is pressed three times, the “F” willappear. The cursor will move on to the next space after a brief pause, so the letter must beselected quickly.Enter a Hard PauseHard pauses allow the SX5D to be used with automated phone systems used for pagers or auto-mated banking. When a number is programmed into the phonebook, a pause is entered bypressing and holding “#” for more than one second. The hard pause will be displayed as “P.”Use Lower Case or NumbersThe “*” key can be used to switch change from upper case(ABC) to lower case (abc) or to numbers (123). The current set-ting will display under the clock in the upper right corner of theLCD screen.Use Special CharactersThe “1” key can access several special characters (punctuationmarks and symbols). To scroll through available special charac-ters, press the “1” key repeatedly.Add a New Entry to the Phonebook1. Press the MENU key.2. Select Phonebook, then select Add Name.3. Enter a name by pressing the alphanumeric keys (maximum 16characters).HINT: Use the “*” key to switch between upper case, lowercase and numbers. Use the “1” key to access special charac-ters. To correct errors in the name, press the CLEAR key.4. Press the OK key.5. Enter the desired telephone number (maximum of 20 digits).6. Press the OK key. You will be prompted to enter another number.7. Press the OK key to save the entry and return to the Phonebook menu. If you have additionalnumbers (up to 2 more) follow steps 5 through 7 for each number.Phonebook Entry Search1. Press the NAME key.2. Use the arrow keys to scroll through the entries or use the keypad to view all entries thatbegin with a specific letter.3. Press the SELECT key to view the phone number(s) listed for a highlighted entry.Edit or Delete an Entry1. Press the NAME key.2. Use the arrow keys to scroll through the entries, or use thekeypad to view all entries that begin with a specific letter.3. Press the SELECT key to view the phone number(s) listed foran entry that is highlighted.4. Press the OPTIONS key and select the desired option.Phonecell®SX5D GSM 11 User ManualEdit or Delete an Entry.Add a New Entry to thePhonebook.Use Lower Case orNumbers.
Speed DialingSpeed dialing permits one-touch dialing for up to 10 telephone numbers stored in the phonebook.Assign a Number to a Speed Dial Location1. Press the NAME key.2. Select the desired entry to add to the speed dial list.3. Press the OPTIONS key.4. Select Add to Speed Dial.5. Use the arrow keys to scroll to a location, then press the SELECT key.NOTE: If a location is already in use, the phone number that is stored there can be replacedwith a new one.Dial a Speed Dial Location1. Pick up the handset or press the SPEAKERPHONE key.2. Press and hold the number of the location containing the speed dial number to be called.3. The number is displayed and dials automatically.View the Speed Dial List1. Press the MENU key.2. Select Phonebook, then select Settings.3. Select Speed Dial List.Change the Display Screen Contrast1. Press the MENU key.2. Select Settings, then select Phone Settings.3. Select Screen Contrast.4. Use the arrow keys to adjust the display contrast.5. Press the OK key.Phonecell®SX5D GSM 12 User ManualView the Speed Dial List.Change the Display ScreenContrast.
Phonecell®SX5D GSM 13 User ManualSX5D ADDITIONAL FEATURESCall LogsThe SX5D stores the telephone numbers of the last ten outgoingcalls and the last ten incoming calls with the dates and times ofthe calls. These numbers are displayed and can be dialed directly from the call log.View the Call Log1. Press the MENU key.2. Select Call Log.3. Select the desired calls to view (All, Missed, Received, Dialed). Calls are denoted by the following icons:Dial a Number From the Call Log1. Press the MENU key.2. Select Call Log.3. Highlight the desired call to dial.4. Pick up the handset or press the SPEAKERPHONE key.5. A dial tone will sound, then the number will be dialed.NOTE: This feature will not work for unavailable or private calls (denoted as Withheld in the Log).Clear the Call Log1. Press the MENU key.2. Select Call Log, then select Clear Logs.3. Select Yes to clear the call log. Select No to return to the CallLog menu.Check the Last Call Time1. Press the MENU key.2. Select Call Log, then select Call Time.3. Select Last Call Time.Check Total Accumulated Air Time1. Press the MENU key.2. Select Call Log, then select Call Time.3. Select All Calls Time.GPRS Call Information1. Press the MENU key.2. Select Call Logs then GPRS Info.Alarm SettingsThe SX5D alarm feature can be used as an alarm clock. Alarm time and tone can be set for daily use or for one time only.Set Alarm Time and Tone1. Press the MENU key.2. Select Clock, then select Set Alarm.3. Select Set Time, then enter the desired alarm time.4. Press the OK key.5. Select Set Tone, then select the desired alarm tone.6. Press the OK key.View All Calls.View Logs.Dialed Calls Received CallsMissed CallsClear the Call Log.Check Total AccumulatedAir Time.Check the Last Call Time.Set Alarm Time and Tone.
Set Alarm to Repeat Daily1. Press the MENU key.2. Select Clock, then select Set Alarm.3. Select Repeat Daily.Turn Alarm On/Off1. Press the MENU key.2. Select Clock, then select Set Alarm.3. Select Alarm Status.4. Select On or Off.5. Press the OK key.Language SelectionThe SX5D is capable of displaying menu items in several different languages. Options include English, French, Portuguese, Russian and Spanish.Select a Language1. Press the left most soft key (MENU).2. Press once (displays Settings option).3. Press the left most soft key (SELECT) twice (selects PhoneSettings option.4. Press three times (displays Set Language option).5. Press the left most soft key (SELECT) once.6. Highlight the desired language, then press the SELECT key.Keyboard SetupSMS text messages can be entered using a standard PC keyboard. The keyboard (not supplied)is connected to the back of the SX5D at the mini-DIN plug. See the Quick Connection Guide inthe front of this manual for connection information. Once connected only the keyboard languagelocale needs to be set to match the keyboard being used.Keyboard Local SetupThe SX5 allows for English, French, Portuguese, Russian and Spanish locales. Each languagehas sub-locales so the exact keyboard type can be properly matched.1. Press the MENU key.2. Select Settings then Phone Settings.3. Select Keyboard Locale then the desired language and locale.Personalization OptionsThe SX5D can be customized with a personal greeting that displays when the SX5D is turned on. It can also be programmed to store your phone number for viewing.Store Your Telephone Number for Viewing1. Press the MENU key.2. Select Settings, then select Phone Settings.3. Select My Number.4. Press the EDIT key.5. Enter your phone number.6. Press the OK key.NOTE: To display your phone number, follow steps 1-3 above.Change Greeting Message1. Press the MENU key.2. Select Settings, then select Phone Settings.3. Select Set Greeting.4. Enter the desired greeting message.Turn Alarm On/Off.Store Your Own TelephoneNumber for viewing.Change Greeting Message.Set Alarm to Repeat Daily.Select a Language.Phonecell®SX5D GSM 14 User Manual
5. Press the OK key.HINT: Use the “*” key to switch between upper case, lower case and numbers. Use the “1” keyto access special characters.Call SettingsMinute MinderWhen turned on, the Minute Minder emits a low audible tone onceevery minute while a call is active.1. Press the MENU key.2. Select Settings, then select Call Settings.3. Select Minute Minder, then select On or Off as desired.Call TimerWhen turned on, the Call Timer displays during an active call. Itcan be set to remain visible for 30 seconds after the call is termi-nated or until another action (key press or taking SX5D off-hook). 1. Press the MENU key.2. Select Settings, then select Call Settings.3. Select Call Timer, then select the desired option. Options include:• Off - no call timer displayed.• On For 30 Sec. - call timer is displayed for 30 seconds or until user action.• On Until Action - call timer is displayed until a user action.PSTN PrefixAllows setup of a prefix that will be added to every outgoing call.1. Press the MENU key.2. Select Settings, then select Call Settings.3. Select PSTN Prefix.• To enable the sending of the prefix for every call, select On.• To disable the sending of the prefix for every call, select Off.• To change the prefix that will be sent for every call if enabled, select Prefix.Dial SettingsIn-Call DTMFIn-Call DTMF allows the SX5D to access automated telephonesystems, such as on-line banking systems, where users mustselect options by dialing digits. 1. Press the MENU key.2. Select Dial Settings, then select Dial Settings.3. Select In-Call DTMF.4. To enable In-Call DTMF, select In Band or Out of Band. To disable DTMF, select None.5. Press the OK key.• In Band - allows the DTMF digits to be sent in the voice channel.• Out of Band* - allows DTMF digits to be sent as a signal to the network.• None - the SX5D will not send DTMF digits to the network.* Recommended methodDial DelayThe Dial Delay is the amount of time, after a digit is dialed, the SX5D waits before automatically sending the call.1. Press the MENU key.2. Select Settings, then select Dial Settings.3. Select Dial Delay.Phonecell®SX5D GSM 15 User ManualMinute Minder.Call Timer.In-Call DTMF.Dial Delay.
4. Use the arrow keys to change the delay time (2-20 seconds).5. Press the OK key.Auto DialThe SX5D is able to recognize frequently called numbers and automatically dial them without waiting for the Dial Delay. Once a number has been called twice successfully, it will Auto Dial whenthis option is turned on.1. Press the MENU key.2. Select Settings, then select Dial Settings.3. Select Auto Dial.4. Select On to enable Auto Dial.Network SettingsNetwork settings allow selection of a desired network and addition of a network operator to thenetwork list.Automatic SelectionThis option allows the SX5D to select the network automatically, based on the SIM Card accountinformation.Manual SelectionThis allows you to see a list of networks in your area. Select the desired network from the listand the SX5D will attempt to use that network.1. Press the MENU key.2. Select Settings, then select Network Settings.3. Select Select Network.4. Select either Automatic or Manual.Set the Preferred NetworkThis option allows networks to be added to the preferred list ofnetworks. Networks on this list will be selected first when the SX5D searches for a network. NOTE: There may be several networks on the list.Insert New Entry1. Press the MENU key.2. Select Settings, then select Network Settings.3. Select Select Network.4. Select Set Preferred.5. Highlight the entry above which the new preferred carrier is to be inserted.6. Press the SELECT key.7. Select Insert.8. Select an entry from the list.Delete Entry1. Press the MENU key.2. Select Settings, then select Network Settings.3. Select Select Network.4. Select Set Preferred.5. Select the desired entry to delete.6. Select Delete.Add New NetworkNew entry will beinserted here.Delete Entry.Insert New Entry.Phonecell®SX5D GSM 16 User ManualAuto Dial.Searching for Network.
If a known network is not on the list, it can be added. The Country Code, Network Code, and Network Name must be provided in order to add a network to the list. Once added to the network list, the network can be accessed via the Set Preferred Network option.1. Press the MENU key.2. Select Settings, then select Network Settings.3. Select Select Network.4. Select Add New Network.5. Press the SELECT key.6. Select Add.7. Enter the correct Country Code, Network Code, and Network Name as prompted.Edit or Delete an Added NetworkNetwork information can be edited or deleted.1. Press the MENU key.2. Select Settings, then select Network Settings.3. Select Select Network.4. Select Add New Network.5. Select the network to be edited or deleted.6. Select Change to edit the network information. Select Delete to delete the network from the list.Change Network Password (Network Dependent)The network password assigned by your service provider can be changed. However, this optionmay not be available from all network providers.1. Press the MENU key.2. Select Settings, then select Network Settings.3. Select Change Network Password.4. Change your password per your network provider’s instructions.SIM PIN SetupSIM PIN1 controls access to SIM Card information. When SIMPIN1 is on, it must be entered each time the SX5D is turned on.Another user can still access the phone with a different SIMCard. SIM PIN2 accesses network-controlled features.NOTE: Contact your network provider for information related toSIM PINs.Turn On/Off SIM PIN11. Press the MENU key.2. Select Settings, then select Security Settings.3. Select SIM PIN1.4. Select On or Off.Automatic SIM PIN EntryWhen SIM PIN1 is enabled, you must enter PIN1 every time the SX5D is powered on. To by-pass this entry but keep the PIN active, simply enable Auto PIN Entry. This allows the SX5D toremember the correct PIN the first time entered. The PIN will then be automatically entered atany future power on. This allows a measure of security where the SIM cannot be used in anotherdevice without knowing the PIN.1. Press the MENU key.2. Select Settings then Security Settings.3. Select Auto PIN Entry then On or Off.NOTE: When SIM PIN1 is disabled, this setting has no effect.Phonecell®SX5D GSM 17 User ManualTurn On/Off SIM PIN1.Add New Network.
Phonecell®SX5D GSM 18 User ManualChange SIM PIN1SIM PIN1 must be enabled and a valid PIN must be entered before this menu item will appear.1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select SIM PIN1.4. Select Change PIN.5. Enter the old PIN, then press the OK key.6. Enter the new PIN, then press the OK key.7. Enter the new PIN again, then press the OK key. NOTE: The PIN must be between 4 and 8 digits. Press the CLEAR key to make changes.Change SIM PIN21. Press the MENU key.2. Select Settings, then select Security Settings.3. Select SIM PIN2.4. Select Change PIN. 5. Enter the old PIN, then press the OK key.6. Enter the new PIN. It must be numerical and between 4 and 8 digits long.7. Press the OK key to save the new PIN, or use the CLEARkey to make changes.Handset Call BarringUse of the SX5D can be restricted by barring certain types of calls from being made or received.Bar All Incoming Calls1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Handset Call Barring.4. Select Bar Incoming, then select On. Select Off to cancel thebar.Bar All Outgoing Calls1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Handset Call Barring.4. Select Bar Outgoing, then select All. Select Off to cancel thebar.Bar Outgoing Calls to Specific Prefixes (No Prefixes Set)You can restrict outgoing calls based on prefixes or numbers that are part of a full phone num-ber. For example, to restrict all outgoing calls made with 847 as the first 3 digits, enter 847 asthe prefix. A maximum of 11 digits can be entered.1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Handset Call Barring.4. Select Bar Outgoing, then select List.5. Since no prefixes have been set, List Empty will be displayed. Select OK, then select Add.6. Enter the prefix you want barred, then press the OK key.7. You can now Add, Edit, Delete, or Clear All prefixes by pressing the OPTIONS key.Bar All Outgoing Calls, viathe Handset.Bar All Incoming Calls, viathe SX5D Handset.Change SIM PIN2.
Bar Outgoing Calls to Specific Prefixes (Prefixes Set)1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Handset Call Barring.4. Select Bar Outgoing, then select List.5. The list of prefixes you have already set will be shown. Youcan now add a new prefix, edit or delete a selected prefix, or clear all prefixes by pressingOPTIONS.Add Additional Prefixes1. Press the OPTIONS key, then select Add.2. Enter the new prefix, then press the OK key.Edit Current Prefixes1. Press the OPTIONS key, then select Edit.2. Use the arrow and CLEAR keys to edit the prefix.3. Press the OK key when finished.Delete Prefixes1. Press the OPTIONS key, then select Delete.2. Press the OK key to delete the prefix. NOTE: Press the BACK key to go back to the previous menu.Clear All Prefixes1. Press the OPTIONS key, then select Clear All.2. Press the OK key to remove all prefixes. NOTE: Press the BACK key to go back to the previous menu.Restricted DialingOutgoing calls can be restricted by creating a Fixed Dialing listthat allows only numbers on that list to be dialed from the SX5D.Add to the Fixed Dialing List1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Fixed Dialing.4. Select Edit Dial List.5. Enter SIM PIN 2, then press the OK key.6. To add a new entry, select Add, enter the new number, then press the OK key. Edit the Fixed Dialing List1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Fixed Dialing.4. Select Edit Dial List.5. Enter SIM PIN 2, then press the OK key.6. Use the arrow keys to highlight the desired entry to edit.7. Press the OPTIONS key.8. Select Edit to change the entry. Select Delete to erase the entry.Activate Fixed Dialing1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Fixed Dialing.4. Select On.5. Enter SIM PIN 2, then press the OK key.Phonecell®SX5D GSM 19 User ManualAdd to or Edit the FixedDialing List.Bar Outgoing Calls to SpecificPrefixes, via the Handset.Activate Fixed Dialing.
Deskphone LockAccess to the SX5D menu options can be restricted by locking the phone. When the deskphoneis locked, a PIN is required to make any calls or access any menu items. Incoming calls can stillbe received. When the SX5D is locked, press the UNLOCK key, then enter the PIN to unlock it.Lock the SX5D1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Deskphone Lock, then select On.4. Enter the PIN (default pin is 1234).Change Deskphone Lock PIN1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Deskphone Lock, then select Change PIN.4. Enter the old PIN, then press the OK key.5. Enter the new PIN, then press the OK key.Closed User Groups (CUG)This feature depends entirely on your service provider and your account subscription. Contactyour service provider for more information.CUG Settings1. Press the MENU key.2. Select Settings then Security Settings.3. Select CUG Settings.Edit a CUG1. Press the MENU key.2. Select Settings then Security Settings.3. Select CUG Settings then select List CUGs4. Press Edit to edit the CUGs.Select a CUG1. Press the MENU key.2. Select Settings then Security Settings.3. Select CUG Settings then select Select4. Press Select on a highlighted CUG.Restore Factory DefaultsAll system features can be reset to the factory defaults.1. Press the MENU key.2. Select Settings, then select Restore Defaults.3. Select Yes to restore all factory default settings.Phonecell®SX5D GSM 20 User ManualRestore Factory Defaults.Lock the SX5D.Change the DeskphoneLock PIN.
SUPPLEMENTARY SERVICES (NETWORK DEPENDENT)In-Call OptionsThe following options are available during a call. While in a call, press the MENU key to accessthese options. Options display based on call status. For example, Retrieve will only display if acall is on hold or if Call Waiting indicates a second incoming call.Hold: Puts active call on hold.Retrieve: Activates a call that is on hold.Swap: Swaps between held call and active call.End Current: Ends the current call.Multiparty: Displays options for managing multiparty calls.Main Menu: Allows access to the Phonebook, Messages, or Call Log features.Call Divert (Forwarding)Call Divert sends incoming calls to another telephone number, even when the SX5D is turned off.Call Divert options include all calls, calls that come in when the line is busy, calls that are notanswered after a specified number of seconds, or calls that come in when the SX5D is powered offor has lost the network signal (Not Found). Certain types of calls can be diverted, such as voice,data, fax, or text messages. Contact your service provider to activate the Call Divert feature.Turn On Call Divert1. Press the MENU key.2. Select Call Divert.3. Select the desired divert type (All Calls, When Busy, NoAnswer, Not Found).4. Select On to divert all types of calls. To specify which types ofcalls to divert, select By Service, highlight the desired service todivert, then press the SELECT key.5. Enter the number to which calls will be diverted, then press theOK key.HINT: Pressing the OK key before entering a number will displaythe Phonebook. Select a number, then press the OK key.Turn Off Call Divert1. Press the MENU key.2. Select Call Divert.3. Select the desired divert type (All Calls, When Busy, NoAnswer, Not Found).4. Select Off.Cancel All Diverts1. Press the MENU key.2. Select Call Divert then Cancel All Diverts.NOTE: When selected, all diverts will be canceled by the network.Phonecell®SX5D GSM 21 User ManualCall Divert (Forwarding).
Call WaitingCall Waiting enables notification of incoming calls when the SX5Dis off-hook (whether during a call or during dialing). To respond toCall Waiting, press the FLASH key or the hook switch. Contactyour service provider to activate Call Waiting.Enable/Disable Call Waiting1. Press the MENU key, then select Settings.2. Select Call Settings, then select Call Waiting.3. Select On to enable. Select Off to disable.Multiparty CallingMultiparty Calling allows connection to several calls simultaneously. Contact your service providerto activate Multiparty Calling.Engage a Multiparty Call1. While in a call, put the call on hold (via a hookflash, FLASHkey, or the menu).2. Dial a second number, then press the FLASH key to connect it.3. When the second call is answered, press the MENU key andthen select Multiparty.4. Select the desired option.Join All: Join the active call with the held multiparty call.Hold All: Place multiparty call on hold.Next: Display the next call party in a multiparty call.Transfer: Connect one call party to another call party and allow the user to leave the call.Exclude: Place the selected party of a multiparty call on hold.Private: Hold a private call with one party in a multiparty call. Other parties are put on hold.I am busy: User defined user busy (UDUB) indicates BUSY to a waiting caller.End All: End active and held calls.NOTE: Options available depend on the status of the call or calls. For example, if only oneother person is in the call, only the End All option will display, or if all the calls have been joined,the Join All option will not display.Caller ID SettingsCaller ID settings allow personalization of how caller’s informa-tion is presented and how your information is presented whenyou call someone who has caller ID capability. Options includeShow caller’s ID, show caller’s number, hide your ID (hides onlyyour name information), show called ID, hide ID if called.1. Press the MENU key.2. Select Settings, then select Call Settings.3. Select Caller ID, then select the desired option.NOTE: LCR Phone and Fax Phone models include a CO Line Caller ID option under the CallerID Settings menu. This allows customization of caller ID information displayed on extensionphones or caller ID devices connected to the SX5D.Blocking Your Number (CLIR)To hide your number when calling others enter # 31 # before you dial the phone number. Forexample, to block your phone number from appearing on 847 555 1212, simply dial # 31 # 847555 1212. This feature is network dependent. Check with your carrier for more information.Phonecell®SX5D GSM 22 User ManualEngage a Multiparty call.Caller ID Settings.Call Waiting.
VoicemailThe VM key will blink and the envelope icon will display when there are new voicemail mes-sages. Contact your service provider to activate voicemail and for voicemail settings.Set Voicemail Access NumbersTypically, your service provider will set the voicemail access numbers for you. If they do not, contact them for the Home Mailbox , Roam Mailbox, Voice, and Message numbers.1. Press the MENU key.2. Select Messages, then select Voicemail.3. Select Voicemail Settings, then select Box Numbers.4. Select Home Mailbox, then enter the number provided by your service provider.5. Press the OK key.6. Follow steps 4 and 5 for the Roam Mailbox.SMS Alert MatchYour network provider may send a text message (SMS) to alert you when you have voicemail. Ifconfigured, the SX5D can match this message to let you know that you have voicemail insteadof just another text message.1. Press the MENU key, then select Messages.2. Select Voicemail, then Voicemail Settings, then Alert Match.3. Enter part of the text you receive when the network sends you an SMS message for voice-mail. You do not have to enter the whole message just part of the message.4. When complete, press the OK key.Check Voicemail1. Press the VM key. You will be connected to your voicemail system automatically.2. Follow the automated instructions.Short Message Service (SMS)The SX5D is capable of sending and receiving SMS text messages. Each SMS message canhave a maximum of 160 characters. Upon receipt of a new SMS message, the message icon(envelope) will be displayed and the SMS key will blink. A maximum of 10 messages can bestored. Contact your service provider to activate SMS.SMS messages can be generated using the SX5D keypad or a standard computer keyboard.See the Quick Connection Guide at the front of this manual to see how to connect a keyboard.Read Received Text Messages1. Press the SMS key.2. Select Received Messages.3. Scroll to the desired message.4. Press the READ key.NOTE: Unread messages are denoted by a closed envelope icon.Reply to Received Messages1. View the desired message.2. Press the OPTIONS key.3. Select Text Reply to reply with a text message. Select VoiceReply to reply with a voicemail.4. For a text reply, type a reply message, then press the OKkey. Selecting Voice Reply will activate the speakerphone andcall the person who sent the message.Phonecell®SX5D GSM 23 User ManualReply to ReceivedMessages.Read Text Messages.Closed envelopeiconSet Voicemail AccessNumbers.
Forward Text Messages1. View the desired message.2. Press the OPTIONS key, then select Forward.3. Enter the desired number or press the NAME key to select aphonebook entry.4. Press the OK key.5. To send the message, select Send Now. To save the messageto send at a later time, select Send Later.Delete Text Messages1. View the desired message.2. Press the OPTIONS key.3. Select Delete.Create Text Messages1. Press the SMS key.2. Select Create Message.3. Enter the message text.NOTE: Use the “*” key on the keypad to change the type of text(all capital letters - ABC, lower case letters - abc, or numbers -123). The current text type is displayed under the clock in theupper right corner of the display screen. Use the “1” key toaccess special characters.4. Press the OK key.5. Enter the desired number, or press the NAME key to select aphonebook entry.6. Press the OK key.7. To send the message, select Send Now. To save the message to send at a later time, select Send Later.View Saved Messages1. Press the SMS key.2. Select Saved Messages.3. Select the desired message.Send Saved Messages1. Press the SMS key.2. Select Saved Messages.3. View the desired message.4. Press the OPTIONS key.5. Select Forward.6. Enter the desired number or press the NAME key to select aphonebook entry.7. Press the OK key.8. To send the message, select Send Now. To save the message to send at a later time, select Send Later.Phonecell®SX5D GSM 24 User ManualCreate Text Messages.Delete Text Messages.View Saved Messages.Send Saved Messages.Forward Text Messages.
Phonecell®SX5D GSM 25 User ManualMessage SettingsMessage CenterThe message center number is used to retrieve your text messages. Contact your service provider for this number.1. Press the SMS key, then select Message Settings.2. Select Message Center, then enter the number that your service provider gave you. NOTE: If the number is already entered, press the OK key.3. Press the OK key.Message LifetimeMessage lifetime is the amount of time that an unread mes-sage will remain on the network server before beingremoved.1. Press the SMS key.2. Select Message Settings.3. Select Message Lifetime.4. Select the desired time for unread messages to remain on the network server.5. Press the OK key.Message FormatThis allows messages to be sent in different formats. Contactyour service provider for information about which messageformats are supported.1. Press the SMS key.2. Select Message Settings.3. Select Message Format.4. Select the desired message format.5. Press the OK key.Information MessagesInformation messages provide information such as phone numbers for taxi services, car rentals,or emergency services. If your service provider offers information messages, you can select thesubjects to view and the language in which to view them. Contact your service provider for moreinformation.Set Information Subjects1. Press the MENU key.2. Select Messages, then select Info messages.3. Select Settings, then select Subject.4. Select Active.5. Press the SELECT key.6. Select Add.7. Select the desired subject from the list.Set Languages1. Press the MENU key.2. Select Messages, then select Info messages.3. Select Settings, the select Set Languages.4. Select the desired language from the list.Message Format.Set Information Subjects.Message Lifetime.
Network Call BarringThe SX5D supports network call barring of incoming or outgoing calls and allows barring of spe-cific types of services, such as voice or data. Contact your service provider to activate networkcall barring.The following call barring options are available:• Foreign Calls: Does not allow international calls.• Only local and home country: Only allows local and home country calls.• Bar Incoming: Does not allow any incoming calls.• Bar Incoming if Abroad: Does not allow any incoming calls when the SX5D is outside thehome network country.• Bar Outgoing: Does not allow any calls to be made.• Bar All: Does not allow any calls to be made or received.• Cancel All: Deactivates any network call bars that are currently active.Activate Call Bars1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Network Call Barring.4. Select the desired type of network call bar to activate (see list above for descriptions of each type).5. Select the desired service to bar.6. Select On.7. Enter the network password, then press the OK key.Deactivate Call Bars1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Network Call Barring.4. Select the desired type of network call bar to deactivate.5. Select the desired service to deactivate.6. Select Off.7. Enter the network password, then press the OK key.Check Call Bar StatusTo see which call bar options are active or inactive:1. Press the MENU key.2. Select Settings, then select Security Settings.3. Select Network Call Barring.4. Select the desired type of network call bar to check.5. Select the desired service, then select Status. The current setting will be displayed.Phonecell®SX5D GSM 26 User ManualActivate Call Bars.Deactivate Call Bars.Check Call Bar Status.
DATA FEATURESWhen connected to a personal computer (PC), the SX5D is capable of sending and receivingdigital fax and data, sending and receiving email communications, and accessing the Internet.Data speeds may vary depending upon your cellular network.Connect SX5D to a ComputerUse a data cable to connect the DB-9 data port on theSX5D to the appropriate data port on your PC.Configure PC for Circuit Switched DataRequirements• Active GSM account with your network serviceprovider including a Data/Fax facility• Windows (version 95/98 or later)• PC with a Com Port.NOTE: When all of the above have been satisfied, you may proceed.Modem Setup1. Power on your PC/laptop.2. Access the Control Panel, then select the Modems option.3. Install a new modem device for the SX5D with the following specifications:Modem Type: Standard 19200 bps ModemMaximum speed of serial port: 19,200Data bits: 8Parity: NoneStop bits: 1Use Flow Control: Enable this option and select Hardware [RTS/CTS]Extra settings: AT & D1Automatic Baud Rate Fall Back ControlWhen there are errors in a data stream, the SX5D baud rate may “fall back” to a default rate of19,200 bps. Some applications cannot handle this change, so the automatic baud rate changecan be disabled on the SX5D. If some applications are having difficulty communicating with theSX5D, disable the automatic fall back, then make sure that the baud rate of the SX5D is thasame as that of your applications. From an application that is capable of sending AT commands through the serial port of the PC(such as HyperTerminal), use the following commands to configure the baud rate of the SX5D:To disable automatic fall back: AT*TPOTS=”#”*132*0#”To enable automatic fall back: AT*TPOTS=”#”*132*1#”To change the baud rate on the SX5D: AT+IPR=<baud rate>To view SX5D supported baud rates: AT+IPR=?Phonecell®SX5D GSM 27 User ManualFigure 20 - DB9 Data Port on the SX5DDB9 Data Port
GPRS (Packet Data) ConnectionsThe SX5D will allow GPRS connectivity if your network service provider has this feature available. GPRS allows packet data connections at higher speeds than conventional circuitswitched (dial-up) connections. A GPRS Kit can be used when you are connecting with GPRSservice. This kit contains a serial cable and a setup CD for installation on a standard personalcomputer. Contact your service provider or nearest dealer for more information.Analog Modem SupportThe SX5D FAX phone model supports connectivity with an analog modem. A PC with a modemor other devices that use a modem, like a credit card swipe Point Of Sale (POS) machine, canbe connected to the RJ-11 jack (marked with a telephone icon) and used seamlessly.Data Port SetupThe RJ-11 voice jack on the SX5D (the jack marked with a phone icon) can be configured forvoice (default setting) or analog modem data. If the jack is configured for analog data, thebypass string for voice calls must be entered before a voice call can be made. In voice mode,data transmissions are routed through the DB-9 port. To send data via an analog modem while invoice mode, use the analog bypass string. 1. Press the MENU key.2. Select Settings, then select Data Settings.3. Select Data Port, then select analog (RJ-11) or Serial (for voice).Using the Bypass StringA bypass string can be used when the default port is not set to RJ11 for data. This string needsto be appended to the beginning of the phone number that the modem is dialing.1. Go off-hook on the RJ11 analog modem jack (jack with phoneicon).2. Dial the bypass string and number: # * 19 * 2 # <number>.ModulationThe analog modem interface supports the following standardsand data rates. The SX5D also supports automatic modulationadjustment. The default is V.8 (Auto).NOTE: This modulation is only for the connection between the modem and the SX5D.1. Press the MENU key.2. Select Settings, then select Data Settings.3. Select Modulation then select the modulation desired.Connection ElementThe SX5D supports both transparent (no error correction) and non-transparent (error correction)data connectivity. Check with your carrier to determine which is right for your application.1. Press the MENU key.2. Select Settings, then select Data Settings.3. Select Air Rate, then select Connection Element.4. Select either Non-Transparent or Transparent.Air Interface Data RatesWhen using an analog modem for data, different data rates overthe air are possible depending on your carrier. If your not surewhat your carrier supports use the default setting Autobauding or ask your carrier.Phonecell®SX5D GSM 28 User ManualData Port Setup.Connection Element.Modulation Baud Rates (bps)V.32bis 14000, 12000, 9600, 7200V.32 (TCM) 9600V.32 9600, 4800V.22bis 2400, 1200V.22 2400, 1200, 600
NOTE: This modulation/data rate is only for the air interface connection between the carrier andthe SX5D.1. Press the MENU key.2. Select Settings, then select Data Settings.3. Select Air Rate, then select Data Rate.Phonecell®SX5D GSM 29 User ManualModulation Over the Air Data RateV.21 300V.22 1200V.23 1200, 75V.22bis 2400V.26ter 2400V.32 9600, 4800V.34 14,400, 9600V.110 14,400, 9600, 4800, 2400, 1200, 300
Telephone Extension Setup*Certain models of the SX5D can support standard telephone extensions. You can connect standardtelphones to the jack marked with a telephone icon. The SX5D can support up to a 5REN load.Connecting Standard Telephones to the SX5D1. Using a RJ-11 cable (not supplied), connect a standard...<SHOW FIGURE HERE>Pulse DialingThe SX5D supports a pulse dialing from a standard telephone connected the extension jack, butit is recommended that you use a DTMF (tone) type telephone.1. Press the MENU key.2. Select Settings then Dial Settings.3. Select Pulse Dialing. The current setting will be displayed. 4. On will enable pulse dialing from an extension phone.Line RingingThis setting changes the cadence of an extension phones ringer. Selection include US style, UKstyle, European style, or off.1. Press the MENU key.2. Select the Settings then Audio Settings.3. Select Line Ringing. The current setting will be displayed.Line LevelThis changes the extension phones audio level. If the extension phone(s) connected does notallow for audio volume adjustment, use this feature.1. Press the MENU key. 2. Select Settings then Audio Settings.3. Select Line Level. The current setting will be displayed.Extension Caller IDThis allows control of the extension line caller ID format for devices that support caller ID. Theselections include MDMF (name and number), SDMF (number only), or off.1. Press the MENU key.2. Selet Settings then Audio Settings.3. Select Extension Alert. The current setting will be displayed.Phonecell®SX5D GSM 30 User Manual
SX5D FIXED WIRELESS LCR PHONEThe SX5D Fixed Wireless LCR (Least Cost Routing) Phone allows calls to be placed through thewireless GSM network or the public switched telephone network (PSTN) - see Figure 21. Thiscapability enables users to take advantage of favorable rates based on type of call (local or long dis-tance), time of call, and receiving party (wireless subscriber or PSTN subscriber).Connect the SX5D Personal LCR Phone to the Landline (PSTN)The SX5D Personal LCR Phone must be connected to the PSTN in order to take advantage ofleast cost routing. Once it is connected, both wireless and PSTN services will be available.Wireless service is the default setting for primary service (what is automatically active when theSX5D goes off-hook). PSTN service can be connected by pressing the FLASH key before enter-ing the phone number. See the Change the Default Service and Change the Alternate ServicePrefix sections of this manual for instructions.1. Using RJ-11 cable (not supplied), connect the PSTN wall jack to the unmarked jack on theSX5D Personal LCR Phone - see Figure 22.NOTE: Make sure to connect the PSTN to the proper RJ-11 jack on the SX5D. Improper connection may damage the SX5D.Change the Default ServiceThis setting changes which service is automatically active when the SX5D goes off-hook.1. Press the MENU key.2. Select Settings, then select Extension Settings.3. Select Service Mode. The current setting will be highlighted.4. To select the wireless network as the default service, select GSM. To select the landline network PSTN as the default service, select PSTN.Phonecell®SX5D GSM 31 User ManualFigure 22 - Connect the SX5D Personal LCR Phone to the Landline PSTN.PSTNto unmarked jackRJ-11 CableChange the Default Service.WirelessNetworkPSTNAdditionalphoneFigure 21 - Personal LCR option.
PSTN Alert SetupThe SX5D can use a different alert tune to denote the difference between a landline call and awireless call.1. Press the MENU key.2. Select Settings then Audio Settings.3. Select Extension Alert. The current setting will be displayed. Make Calls via the Alternate Service1. Pick up the handset.2. Press the FLASH key. The alternate service will be displayed. 3. Dial the desired number.Connect Additional Phones to the SX5D Personal LCR PhoneMultiple phones can be connected to the SX5D Personal LCR Phone (up to a 5 REN load canbe supported). Any additional phones (extensions) attached to the SX5D will only be able toaccess the GSM network. No calls can be made or received via the PSTN on the extensionphones. See Telephone Extension Setup section of this manual for more information.HINT: When an extension phone goes off-hook, “External dialing...” will display on the SX5Dscreen.SX5D FIXED WIRELESS FAX PHONEThe SX5D Fixed Wireless Fax Phone allows connection to a fax machine and additional tele-phones. The SX5D can be set up to use one or both of its RJ-11 jacks. In Single Jack mode,only the jack designated with a telephone icon is operational. A fax machine or an additional tele-phone can be connected to that jack. In Dual Jack mode, the unmarked jack is used for fax, andthe jack marked with the telephone icon is used for any additional phones.Fax Timing AdjustmentsPhase D adjustments can be made to alalog faxing. If you experience faxing issues try adjustingthis setting.1. Press the MENU key.2. Select Settings then Fax Settings.3. Select Bypass Phase D Repeat.4. Select On and then adjust Duration until your analog fax application is successful.Phonecell®SX5D GSM 32 User ManualFigure 23 - Connect the SX5D Personal LCR Phone to additional phones.Standard telephoneRJ-11 Cable
Dual Jack SetupThis feature allows the operation of a fax machine without entering a prefix before sending a fax.The fax machine must be connected to the unmarked RJ-11 jack on the SX5D. Any extensionphones must be connected to the RJ-11 jack marked with a phone icon - see Figure 24.1. Press the MENU key.2. Select Settings, then select Fax Settings.3. Select Analog Fax Jack.4. Select Dual Jack.Digital Fax SetupThe SX5D is capable of receiving and send faxes via a personal computer using a standardRS232 serial port. The PC application and modem setup must be able to support software flowcontrol. To setup flow control properly, follow the instructions for setting up a standard modemconnection in Appendix A of this manual with the following changes.HINT: Setup a separate modem for PC fax and a separate modem for PC circuit switched dataconnections. This way you will not have to make changes to the modem settings every time youwant to use fax or data.1. Change the flow control of the standard modem to enable software flow control.2. Change Extra Settings from AT&D1 to AT+IFC=1,1 &d1. This enabled software flow controlon the SX5D.3. On the SX5D, select the serial port for your data connections by entering the MENU, thenselecting Settings, then Fax Port, then Data Port, and then Serial Port (DB9).4. Run your PC fax application using this new modem connection for receiving and sendingfaxes.Phonecell®SX5D GSM 33 User ManualFigure 24 - Connect the SX5D for dual jack mode.To unmarked jackRJ-11 CableRJ-11 Cable
Single Jack SetupThis feature allows both the fax machine and extension phones to use the same RJ-11 jack onthe SX5D (as in the case of combination fax/phones). Connect a fax machine to the phone jackon the SX5D that is marked with a telephone icon - see Figure 25.1. Press the MENU key.2. Select Settings, then select Fax Settings.3. Select Analog Fax Jack.4. Select Single Jack.Analog Fax BypassIn single jack mode, the SX5D default is for voice calls, so a fax by-pass must be entered tosend faxes. After a fax is sent, the SX5D will automatically reset itself for voice calls.1. Lift up the handset (take off-hook).2. Press: # *19 *1 #, then dial the fax number to be called.3. Press START on the fax machine.HINT: If the fax machine does not have a handset, enter # *19 *1 #, followed by theremote fax number to be called. Press START.Routing Faxes to the Serial Port1. Press the MENU key.2. Select Settings, then select Fax Settings.3. Select Port, then select Serial Port.NOTE: The SX5D must be connected to a computer, or other device that is set up for digitaldata, via the serial connector in order to send or receive digital faxes.Phonecell®SX5D GSM 34 User ManualFigure 25 - Connect the SX5D for single jack mode.This RJ-11 Jack is not usable.RJ-11 CableOR
SX5D TROUBLESHOOTINGTelephone Service is Not Working (Cannot make or receive calls)· Make sure the SX5D powered on properly.· Make sure any equipment that is externally connected to the SX5D is correctly connected.· Test any externally connected equipment on a known system to verify operation.· Do you have the antenna connected? If not, connect the antenna.· Is service established with a service provider? If so, is there any service provider issue. Your serv-ice may be disconnected or not functioning properly. Contact your service provider is you think thisis the problem.Unable to Receive Calls·Is the handset on the cradle? If not, place the handset on the cradle and try again.· Is the SX5D making a loud repetitive tone (ROH)? Then either speakerphone or the handset is offhook. Hang-up and try again. Unable to Make Calls· If you do not hear standard dial tone when off hook, then your service has a problem. Contactyour service provider is you think this is the problem.· Do you have telephone extensions connected to the SX5D? If so, one of those may be off hook(the display will show this information).Unable to Send or Receive Analog Fax Calls· Is your fax machine connected properly? You may have the fax machine connected to the wrongRJ-11 jack of the SX5D. Make sure it is connected to the jack with no symbol (no phone icon). If youwant to use the SX5D in single jack mode, please refer to the fax section of this manual for propersetup.· Do you have fax service on your wireless account? Contact your service provider for information.· Do you have good signal strength? If you signal is low it may affect faxing. Try repositioning theunit or obtaining a direction high gain external antenna.Unable to Send or Receive Circuit Switched Data (CSD) Calls· Is your computer connected to the serial port of the SX5D? If not, connect the computer with anappropriate RS232 DB-9 cable.· Do you have CSD service on your wireless account? Contact your service provider for information.· Is your computer configured properly to access data service with the SX5D? Please reference thedata sections of this manual for proper setup.Unable to Connect to GPRS Service· Is your computer connected to the serial port of the SX5D? If not, connect the computer with anappropriate RS232 DB-9 cable.· Do you have GPRS service on your account? Contact your service provider for information.· Is your computer configured properly to access GPRS with the SX5D? Please reference the datasections of this manual for proper setup or your GPRS setup wizard help file for more information.· You cannot pass the dialing sequence of the connection. Make sure that DTE Fallback is disabled.See the data section of the manual for more information.· You can dial the connection but cannot authenticate with the network. There may be a network oraccount setup problem. Contact your service provider for more information.Moisture or Ventilation Problems· Is moisture forming on or around the SX5D? Remove any moisture with a clean dry towel andmove the unit to a well ventilated area. Review the Temperature and Environment section of thismanual for more information.No Power· Is the power supply connected to the unit? Make sure power is available and that the power sup-ply is properly connected to the SX5D.· The power supply is connected but the unit still has no power. Make sure the circuit is functioningto the power supply. Check breakers & contact your power company. Power may be off at location.Phonecell®SX5D GSM 35 User Manual
CONFORMANCE STATEMENTSThe SX5D 850/1900 MHz (Dual Band) model conforms to the requirements of the applicableEU CE Council Directives.FCC Part 15 Class B ComplianceThis Phonecell®SX5 model has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. Changes or modifications not expresslyapproved by Telular Corporation will void your authority to operate the equipment per FCC part15 paragraph 15.21.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radioor television reception, which can be determined by turning the equipment OFF and ON, the useris encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the antenna.• Increase the separation between the equipment and the terminal.• Connect the equipment into an outlet on a circuit different from that to which the terminal isconnected.• Consult your Authorized Telular Distributor or an experienced radio/TV technician for help.All SX5D 850/1900 MHz (Dual Band) models are in conformance with all applicableAustralian government telecommunications requirements.All SX5D 850/1900 MHz (Dual Band) models have hygienic conclusion of GOSSANEPID-NADZO and conform to GOSSTANDARD of Russia.All SX5D 850/1900 MHz (Dual Band) models are in conformance with all applicable SouthAfrican government telecommunications requirements.SAFETY INFORMATIONThe Phonecell®SX5 functions as both a radio transmitter and receiver. When it is ON, the SX5receives and sends out radio frequency (RF) energy. The SX5 GSM 850/1900 Dual-Band unitoperates in the frequency range of 824 MHz to 849 MHz and 1850 MHz to 1910 MHz. This unitemploys commonly used phase/frequency modulation techniques. When you use the SX5, thecellular system handling your call controls the power level at which the unit transmits.Exposure to RF (Radio Frequency) EnergyIn 1991, the Institute of Electrical and Electronics Engineers (IEEE), and in 1992, the AmericanNational Standards Institute (ANSI), updated the 1982 ANSI Standard for safety levels withrespect to human exposure to RF energy. After reviewing the available body of research, morethan 120 scientists, engineers and physicians from universities, government health agencies andindustry developed this updated Standard. In March, 1993, the U.S. Federal CommunicationsCommission (FCC) proposed the adoption of this updated Standard.The design of your Telular Phonecell®SX5 complies with this updated Standard. Of course, ifyou want to limit RF exposure even further than the updated ANSI Standard, you may choose tocontrol the duration of your calls and operate your phone in the most power-efficient manner.Safe Operation RequirementThe Phonecell®SX5 must be either wall mounted or desk mounted and should not be operatedwhen any person is within 203 mm (8 inches) of the antenna.Temperature EnvironmentOperating Temperature: From -10°C to +50°C ; Up to 95% relative humidity (non-condensing).Storage Temperature: From -40°C to +60°C; Up to 95% relative humidity (non-condensing).Phonecell®SX5D GSM 36 User ManualTA-2002/058ApprovedN12847
Antenna Care and ReplacementDo not use the Phonecell®SX5 with a damaged antenna. If a damaged antenna comes into con-tact with the skin, a minor burn may result. Have your antenna replaced by a qualified technicianimmediately. Use only a manufacturer-approved antenna. Unauthorized antennas, modifications,or attachments could damage the Phonecell®SX5.DrivingCheck the laws and regulations on the use of cellular products in the areas where you drive.Some jurisdictions prohibit your using a cellular device while driving a vehicle. Even if your juris-diction does not have such a law, we strongly suggest that, for safety reasons, the driver useextreme caution when operating the cellular device while the vehicle is in motion. Always obeythe law.Electronic DevicesMost modern electronic equipment is shielded from RF energy. However, RF energy from cellulardevices may affect inadequately shielded electronic equipment.RF energy may affect improperly installed or inadequately shielded electronic operating andentertainment systems in motor vehicles. Check with the manufacturer or its representative todetermine if these systems are adequately shielded from external RF energy. You should alsocheck with the manufacturer of any equipment that has been added to your vehicle.Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids,etc.) to determine if they are adequately shielded from external RF energy.Turn your Phonecell®SX5 OFF in health care facilities when any regulations posted in the areasinstruct you to do so. Hospitals or health care facilities may be using equipment that could besensitive to external RF energy.AircraftTurn OFF your Phonecell®SX5 before boarding any aircraft.• Use it on the ground only with crew permission.• Do not use it in the air.To prevent possible interference with aircraft systems, U.S. Federal Aviation Administration (FAA)regulations require you to have permission from a crew member to use your cellular phone (orany other cellular product) while the plane is on the ground. To prevent interference with aircraftsystems, FCC regulations prohibit using your cellular device while the plane is in the air.ChildrenDo not allow children to play with your Phonecell®SX5 to prevent damage to the unit.Blasting AreasConstruction crews often use remote control RF devices to set off explosives. Therefore, to avoidinterfering with blasting operations, turn your Phonecell®SX5 OFF when in a "blasting area" or inareas posted: "Turn off two-way radio."Potentially Explosive AtmospheresTurn your Phonecell®SX5 OFF when in any area with a potentially explosive atmosphere. It israre, but your Phonecell®or its accessories could generate sparks. Sparks in such areas couldcause an explosion or fire resulting in bodily injury or even death.Areas with a potentially explosive atmosphere are often, but not always, clearly marked. Theyinclude fueling areas such as gas stations; below deck on boats; fuel or chemical transfer orstorage facilities; areas where the air contains chemicals or particles, such as grain, dust, ormetal powders; and any other area where you would normally be asked to turn off your vehicleengine.Do not transport or store flammable gas, liquid or explosives in the area of your Phonecell®oraccessories.Vehicles using liquefied petroleum gas (such as propane or butane) must comply with theNational Fire Protection Standard (FPA-58). For a copy of this standard, contact the National FireProtection Association, One Batterymarch Park, Quincy, MA 02269, Attn: Publications SalesDivision.Phonecell®SX5D GSM 37 User Manual
WARRANTYI. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:TELULAR CORPORATION ('Telular") warrants to a distributor Buyer, or to a customer only if thecustomer is a Buyer directly from Telular, that the Products (including accessories) shall complywith the applicable Specifications and shall be free from defects in material and workmanshipunder normal use and service for a period of fifteen (15) months from date of shipment fromTelular. Telular, at its option, shall at no charge either repair, replace or refund the purchase priceof the Product during the warranty period, provided it is returned by Buyer in accordance with theterms of this warranty to the Telular designated repair center. Repair or replacement, at Telular'soption, may include the replacement of parts, boards or Products with functionally equivalentreconditioned items. Repaired and replacement items are warranted for the balance of the origi-nal warranty period. All replaced items shall become the property of Telular. SUCH ACTION ONTHE PART OF TELULAR SHALL BE THE FULL EXTENT OF TELULAR'S LIABILITY HERE-UNDER, AND BUYERS EXCLUSIVE REMEDY. Buyer shall be responsible for all costs andexpenses incurred by Buyer including without limitation any handling, labor or transportationcharges. OTHER THAN AFORESAID, THIS EXPRESS WARRANTY IS EXTENDED BY TELU-LAR TO BUYER ONLY AND NOT TO BUYER'S CUSTOMERS OR USERS OF BUYER'SPRODUCTS.II. HOW TO OBTAIN WARRANTY SERVICEProduct covered under this warranty shall only be accepted from and returned to Buyer's desig-nated repair center. Buyer's dealers, distributors, agents, and end users cannot submit items toTelular under this warranty. To receive warranty service an RMA number must first be obtainedfrom Telular Technical Support. The defective or non-compliant Product should be sent by Buyerfreight pre-paid to: Telular Corporation, 647 North Lakeview Parkway, Vernon Hills, IL 60061,USA or other designated location. The product must be packaged in the original carton andpacking material or an equivalent package and must have the assigned RMA number clearlymarked on the carton. Returned Product received without an RMA number will be returned to thesender.III. WARRANTY CONDITIONS:This is the complete warranty for the Products manufactured by Telular and sold to Buyer. Telularassumes no obligation or liability for additions or modifications to this warranty unless made inwriting and signed by an officer of Telular. Unless made in separate written agreement betweenTelular and Buyer, Telular does not warrant the installation, field maintenance or service of theProducts or parts.TELULAR CANNOT BE RESPONSIBLE IN ANY WAY FOR ANY ANCILLARY EQUIPMENTNOT FURNISHED BY TELULAR WHICH IS ATTACHED TO OR USED IN CONNECTION WITHTHE PRODUCTS OR FOR OPERATION OF THE PRODUCTS WITH ANY ANCILLARY EQUIP-MENT AND ALL SUCH EQUIPMENT IS EXPRESSLY EXCLUDED FROM THIS WARRANTY.FURTHERMORE, TELULAR CANNOT BE RESPONSIBLE FOR ANY DAMAGE TO THEPRODUCTS RESULTING FROM THE USE OF ANCILLARY EQUIPMENT NOT FURNISHEDBY TELULAR FOR USE WITH THE PRODUCTS.WHEN THE PRODUCT IS USED IN CONJUNCTION WITH ANCILLARY OR PERIPHERALEQUIPMENT NOT MANUFACTURED BY TELULAR, TELULAR DOES NOT WARRANT THEOPERATION OF THE PRODUCT/PERIPHERAL COMBINATION, AND TELULAR SHALLHONOR NO WARRANTY CLAIM WHERE THE PRODUCT IS USED IN SUCH A COMBINA-TION AND IT IS DETERMINED BY TELULAR THAT THERE IS NO FAULT WITH THE PROD-UCT. TELULAR DISCLAIMS LIABILITY FOR RANGE, COVERAGE, AVAILABILITY, OROPERATION OF THE CELLULAR SYSTEM WHICH IS PROVIDED BY THE CARRIER.Phonecell®SX5D GSM 38 User Manual
IV. WHAT THIS WARRANTY DOES NOT COVER:(a) Subsequent upgrades and enhancements to the Product. (b) Defects, non-compliance ordamage resulting from use of the Product in other than its normal and customary manner orenvironment. (c) Defects, noncompliance or damage from misuse, lightening, accident or neg-lect. (d) Defects, noncompliance or damage from improper testing, operation, maintenance,installation, adjustment, or any alteration or modification of any kind. (e) Product disassembled orrepaired in such a manner as to adversely affect performance or prevent adequate inspectionand testing to verify any warranty claim. (f) Product which has had the serial number removed ormade illegible. (g) Defects, non-compliance or damage due to spills of food or liquid. (h) All plas-tic surfaces and all other externally exposed parts that are scratched or damaged due to cus-tomer normal use. (i) Costs and expenses, including without limitation handling, labor and trans-portation, incurred in returning Product for warranty service to Telular's Repair Center. (j) Repair,programming or servicing by someone other than Telular.V. GENERAL PROVISIONS:THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS OR STATUTORY WAR-RANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WAR-RANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE,INFRINGEMENT, DELIVERY, NEGLIGENCE AND PERSONAL INJURY, ARE DISCLAIMED.FURTHER, AS THE CELLULAR CARRIER IS NOT CONTROLLED BY TELULAR, NO WAR-RANTY IS MADE AS TO COVERAGE, AVAILABILITY OR GRADE OF SERVICE PROVIDEDBY THE CELLULAR CARRIER. IN NO EVENT SHALL TELULAR BE LIABLE FOR DAM-AGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OFUSE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAV-INGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUTOF THE USE OR INABILITY TO USE SUCH PRODUCT TO THE FULL EXTENT SUCH MAYBE DISCLAIMED BY LAW. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION ORLIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOWLONG AN IMPLIED WARRANTY LASTS.VI. SOFTWARE PROVISIONS:Laws in the United States and other countries preserve for Telular certain exclusive rights forcopyrighted Telular software such as the exclusive rights to reproduce in copies and distributecopies of such Telular software. Telular software may be copied into, used in and redistributedwith only the Product associated with such Telular software. No other use, including without limi-tation, disassembly of such Telular software or exercise of exclusive rights in such Telular soft-ware is permitted and Telular reserves all rights not expressly granted in this Limited CommercialWarranty.Patents:Telular Corporation products are protected and manufactured under one or more of the followingU.S. patents and related international patents and patents pending relating thereto: 4,658,096;4,737,975; 4,775,997; 4,868,519; 4,922,517; 5,134,651; 5,361,297; 5,469,494; 5,046,085;5,715,296.Trademarks:Telular Corporation owns the following registered trademarks: TELULAR and design, TELULAR,CELJACK, MAXJACK, TELCEL, HEXAGON LOGO, PHONECELL, CELSERV, TELGUARD,CPX, and AXCELL.Phonecell®SX5D GSM 39 User Manual
Phonecell®SX5D GSM 40 User ManualNOTES
APPENDIX APC SERIAL PORT SETUP FOR CIRCUIT SWITCHED DIGITAL FAX ANDDATA (not for use with GPRS)Requirements· GSM account with your network service provider including a circuit switched data and faxfacility.· PC, laptop, notebook with a RS232 serial port.· Windows 98 or better.· RS-232 Cable (DB9 to DB15).NOTE: When all of the above have been satisfied, you may proceed.Modem Setup1) Power on your PC or device that is connected to the SX5D.2) Power on your PC/laptop and start Windows 95/98 2) Click the “Start” button (if using a Windows operating system), select "SETTINGS" and then"CONTROL PANEL". Once the Control Panel window appears double click the MODEMS iconbutton. The modem properties window will appear. NOTE: Other modems may appear in the list of installed modems.3) Click the ADD button to install a new modem device for the phonecell.Phonecell®SX5D GSM 41 User Manual
4) The Install New Modem window may appear asking for the type of modem to install. Select"Other" followed by clicking the NEXT button. If this window does not appear, go to Step 5.5) The Install New Modem window will appear. Then, click on the "Don't detect my modem option"followed by clicking the NEXT button.Phonecell®SX5D GSM 42 User Manual
6) The Install New Modem will update again to select the manufacture an dthe modemmodel.Select “Standard Modem Types” from the Manufactures list. Select “Standard 1900 bpsModem” from the Models list then click next.7) The Install New Modem will update to select the COM port. Select the COM port that will be con-nected to the SX5D then click Next. Windows will now create a modem configuration file for thePhonecell ® SX5. This may take several minutes. 8) The Install New Modem window will updateagain. Click on Finish to proceed. Phonecell®SX5D GSM 43 User Manual
8) The Modems Properties window should appear. Click on the Properties button.9) The Standard 19200 bps Modem Properties window will open in the General tab. Set as shownwith the COM port you have selected. 10) Then click on the Connection tab. Set as shown below. Phonecell®SX5D GSM 44 User Manual
11) Click on the Advanced button. Set as shown. 12) Click on OK and Close to back out of each window. Your modem is now set up.NOTE: When using the SX5D for PC fax operation, make sure the modem connection uses soft-ware flow control. When using PC data, either hardware or software flow control can be used, aslong as the PC application (and modem) match the SX5D's configuration. The SX5D defaults tohardware flow control. The following AT commands are used to change the SX5D's flow control.Enable Software Flow Control: AT+IFC=1,1Enable Hardware Flow Control: AT+IFC=2,2Disable Flow Control: AT+IFC=0,0Phonecell®SX5D GSM 45 User Manual
NOTESPhonecell®SX5D GSM 46 User Manual
NOTESPhonecell®SX5D GSM 47 User Manual
NOTESPhonecell®SX5D GSM 48 User Manual
7/28/03 Part Number 56029701

Navigation menu