Texas Instruments Deutschland MRD2EVM RFID Reader User Manual MRD2EVM Microreader Evaluation Kit

Download:
Mirror Download [FCC.gov]
Document ID	1744869
Application ID	CmmRz649Yu/k63szqVsIlQ==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	196.66kB (2458231 bits)
Date Submitted	2012-07-17 00:00:00
Date Available	2012-07-17 00:00:00
Creation Date	2012-07-16 09:50:42
Producing Software	iText 2.1.7 by 1T3XT
Document Lastmod	2012-07-16 09:55:28
Document Title	MRD2EVM Microreader Evaluation Kit
Document Creator	TopLeaf 7.6.028
Document Author:	Texas Instruments, Incorporated

MRD2EVM Microreader Evaluation Kit
User's Guide
Literature Number: SCBU050
July 2012
Contents
Microreader Overview ..........................................................................................................
Kit Contents .......................................................................................................................
Download the Software ........................................................................................................
Installation .........................................................................................................................
........................................................................................................ 6
4.2
RI-STU-MRD2 Demo Software (GUI) Installation ................................................................... 9
RI-STU-MRD2 Demo Software (GUI) Introduction .................................................................... 9
Demo Examples ................................................................................................................ 10
6.1
Demo 1: Read or Write LF Transponder (Read Only/ Read Write) – Tab 1 ................................... 10
6.2
Demo 2: Read or Write LF Transponder (MPT 16/17) – Tab 1 .................................................. 11
6.3
Demo 3: HDX+ Transponder (Read or Write Memory) – Tab 1 ................................................. 12
6.4
Demo 4: OTP Transponder (Read or Write ID) – Tab 2 .......................................................... 13
6.5
Demo 5: HDX+ Transponder (Read or Write ID) – Tab 2 ........................................................ 14
6.6
Demo 6: HDX+ Transponder (Trim Frequency) – Tab 2 ......................................................... 15
6.7
Demo 7: HDX+ Transponders (Inventory Command) – Tab 3 ................................................... 16
6.8
Demo 8: PaLFI (Read, Write, Battery Charge and Check, and Flash LED) – Tab 4 ......................... 17
Schematics ....................................................................................................................... 18
7.1
RI-STU-MRD2 EVM Board ........................................................................................... 18
4.1
Driver Installation
Table of Contents
SCBU050 – July 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
List of Figures
RI-STU-MRD2 EVM Board ................................................................................................ 4
MRD2EVM Carton Box With Contents ................................................................................... 5
Windows Security ........................................................................................................... 6
Driver Installed Successfully ............................................................................................... 6
New Hardware Wizard, Step 1 ............................................................................................ 7
New Hardware Wizard, Step 2 ............................................................................................ 7
New Hardware Wizard, Step 3 ............................................................................................ 8
New Hardware Wizard, Step 4 ............................................................................................ 8
RI-STU-MRD2 Demo Software (GUI): Startup Screen
10
Read or Write LF Transponder (Type: Read-Only or Read/Write).................................................. 10
11
Read or Write LF Transponder (Type: MPT 16/17) ................................................................... 11
12
Read or Write Memory Content of HDX+ Transponder .............................................................. 12
13
Read or Write ID of OTP Transponder ................................................................................. 13
14
Read or Write ID of HDX+ Transponder
15
Trim Resonance Frequency of HDX+ Transponder .................................................................. 15
16
Read Inventory of HDX+ Transponder
17
Read, Write, Battery Charge, Battery Check, and Flash LED of PaLFI ............................................ 17
18
RI-STU-MRD2 EVM Board Schematic
................................................................
...............................................................................
.................................................................................
.................................................................................
14
16
18
List of Tables
Kit Contents .................................................................................................................. 5
GUI Tabs ..................................................................................................................... 9
SCBU050 – July 2012
Submit Documentation Feedback
List of Figures
Copyright © 2012, Texas Instruments Incorporated
User's Guide
SCBU050 – July 2012
MRD2EVM Microreader Evaluation Kit
WARNING
The terminals across the antenna connectors SJ1 and SJ2, the
through-hole contact below mark R6-->R7, and the through-hole
contacts 16 and 19 of CON3 operate at potentially hazardous
voltages. Effective safety application procedures and knowledge
are required to minimize risk of electrical shock hazard when using
this EVM. The user should be technically qualified to operate this
EVM, including having full knowledge of risks associated in
working with electrically live and hazardous voltages commonly
found in development platforms. Careful review of General Texas
Instruments High Voltage Evaluation Module (TI HV EVM) User Safety
Guidelines at the end of this document is required prior to using
this EVM.
Microreader Overview
The microreader evaluation board (RI-STU-MRD2) is a complete USB-based reader module providing the
hardware and software to communicate with TI's low-frequency (LF), half-duplex (HDX), and advanced
transponders for programming and tuning after the production phase.
The USB reader-writer stick contains the RI-STU-MRD2 DIL module, which is mounted on an antenna
base board with a USB connector. The RI-STU-MRD2 is backward compatible with the RS232 based RISTU-MRD1 reader module.
Figure 1. RI-STU-MRD2 EVM Board
MRD2EVM Microreader Evaluation Kit
SCBU050 – July 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Kit Contents
www.ti.com
The main features of the RI-STU-MRD2 are:
• RS232 and USB interfaces
• Multi-purpose I/Os
• Low-power operation (2.7 V to 5.5 V)
• Supports programming and tuning of advanced transponders
• Easy to design in and use
Kit Contents
Figure 2. MRD2EVM Carton Box With Contents
Table 1. Kit Contents
Pos
Ref Des
Part Type
Box
Carton Box MSP430
Foam
Foam Protection
Samples
Order or Specification
Number
RI-TRP-DR2B-30
RI-TRP-RR2B-30
RI-TRP-WR2B-30
RI-TRP-RR3P-30
RI-TRP-WR3P-30
TRPGR30TGC
RI-TRP-R9QL-30
RI-TRP-W9QL-30
Samples
Carrier Board
PCB MRD2EVM V2.0
Microreader
RI-STU-MRD2
Manual
11-06-21-073
Label
SCBU050 – July 2012
Submit Documentation Feedback
MRD2EVM Microreader Evaluation Kit
Copyright © 2012, Texas Instruments Incorporated
Download the Software
www.ti.com
Download the Software
Download the latest version of the following files:
1. RI-STU-MRD2 reference manual: SCBU049
2. RI-STU-MRD2 demo software (GUI): xxxxxx
3. USB device driver: xxxxx
4. Additional documents, such as application reports and white papers: http://www.ti.com/rfid
5. RI-STU-MRD2 product folder: http://www.ti.com/tool/RI-STU-MRD2
Installation
4.1
Driver Installation
1. Download the driver from the link specified in 3.Download the software.
2. Proceed according to the type of Operating system.
4.1.1
1.
2.
3.
4.
Windows 7 or Later
Remove the RI-STU-MRD2 EVM board if it is already connected to USB Port.
Right click on the driver file and click INSTALL.
Click YES if Windows prompts for authentication from User Account Control.
Click "Install this driver software anyway", if Windows prompts for authentication.
Figure 3. Windows Security
5. Connect the reader. After installation is complete, the message shown in Figure 4 is displayed.
Figure 4. Driver Installed Successfully
6. The USB driver is now installed on the PC, and the system is ready for use.
MRD2EVM Microreader Evaluation Kit
SCBU050 – July 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Installation
www.ti.com
4.1.2
Windows XP
1. Connect the RI-STU-MRD2 EVM to USB port. When the window shown in Figure 5 is displayed, click
"Yes, this time only" and then click Next.
Figure 5. New Hardware Wizard, Step 1
2. When the window shown in Figure 6 is displayed, click "Install from a list or Specific location" and then
click Next.
Figure 6. New Hardware Wizard, Step 2
SCBU050 – July 2012
Submit Documentation Feedback
MRD2EVM Microreader Evaluation Kit
Copyright © 2012, Texas Instruments Incorporated
Installation
www.ti.com
3. When the window shown in Figure 7 is displayed, click Browse, select the location of the downloaded
driver file on the PC, and then click Next.
Figure 7. New Hardware Wizard, Step 3
4. If Windows prompts for authentication, continue with the installation. After successful installation, the
window shown in Figure 8 is displayed. Click Finish.
Figure 8. New Hardware Wizard, Step 4
5. The USB driver is now installed on the PC, and the system is ready to use.
MRD2EVM Microreader Evaluation Kit
SCBU050 – July 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
RI-STU-MRD2 Demo Software (GUI) Introduction
www.ti.com
4.2
RI-STU-MRD2 Demo Software (GUI) Installation
Download the driver from the link specified in 3.Download the software
1. Unpack RI-STU-MRD2 Demo Software.zip.
2. Double click the RI-STU-MRD2 Demo Reader Software.exe.
RI-STU-MRD2 Demo Software (GUI) Introduction
The RI-STU-MRD2 demo Software supports simple reading/programming of LF HDX, HDX+, Advanced
HDX+ and PaLFI Transponders. When the reader connects to the USB port, the software automatically
detects the reader and the COM port data is displayed on the top as shown in below in Figure 9. The five
tabs described in Table 2 define use mode depending on type of transponders.
Table 2. GUI Tabs
Tab
Name
LF / HDX+
Contents and Functions
OTP/HDX+
Programming/Tuning
Read or write LF tags (R/O, R/W, or MPT 16 /17); read or write memory of HDX+ tags
HDX+ Inventory
PaLFI Transponder
About
Read or write ID; HDX+ tag read or write ID and tune resonance frequency
Inventory process (read aids of group of HDX+ transponders)
Read, write, battery check, battery charge, MSP access
Software and hardware version of the RI-STU-MRD2 reader
The initial screen view with the tabs and COM port data is shown in Figure 9.
COM Port data with version
Tab 1
Tab 2
Tab 3
Tab 4
Tab 5
Figure 9. RI-STU-MRD2 Demo Software (GUI): Startup Screen
SCBU050 – July 2012
Submit Documentation Feedback
MRD2EVM Microreader Evaluation Kit
Copyright © 2012, Texas Instruments Incorporated
Demo Examples
www.ti.com
Demo Examples
6.1
Demo 1: Read or Write LF Transponder (Read Only/ Read Write) – Tab 1
Figure 10. Read or Write LF Transponder (Type: Read-Only or Read/Write)
10
Check Tag Type button: Shows the tag type at position 4 (Transponder Type).
Read Tag button: Reads transponder data, depending on the transponder type.
For read only and read/write transponder types, shows LF-8 byte data with 2-byte CRC and data at
position 6 of Figure 10.
For MPT 16/17 types, shows 16/17 pages with each page of 8-byte data and 2-byte CRC at
position 10 of Figure 11.
For HDX+ types, shows 16 pages of 4-byte data at position 12 of Figure 12.
Write Tag button: Programs the transponder, depending on the transponder type.
For LF-R/W type transponders, writes 8-byte data with 2-byte CRC (or) 10-byte data. Data can be
edited at position 6 of Figure 10 as described in position 6, below.
For MPT 16/17 type transponders, writes 16/17 pages with each page of 8-byte date and 2-byte
CRC. Data can be edited at position 10 of Figure 11 as described in Section 6.2.
For HDX+ type transponders, writes 16 pages of 4-byte data. Data can be edited at position 12 of
Figure 12 as described in Section 6.3.
Shows the type of the transponder. If no transponder is found, "no transponder detected" is shown.
Shows the status (success or error) of the most recent activity.
Shows the 10-byte data field (8-byte ID and 2-byte CRC) of the LF Transponder (R/O or R/W) in
the first row of the table. Data appears after the successful read of transponder.
The Lock column on the right side of table shows the lock status of every single memory row. To
lock the transponder check the Lock box and click Write Tag.
Check the Calc CRC box to write 8-byte data (the CRC is calculated by the reader).
Uncheck the Calc CRC box to write 10-byte data (the CRC is not calculated by the reader).
Shows the last 20 commands transmitted to reader.
Shows the last 20 commands received from reader.
Continuous mode operation check box.
MRD2EVM Microreader Evaluation Kit
SCBU050 – July 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Demo Examples
www.ti.com
6.2
Demo 2: Read or Write LF Transponder (MPT 16/17) – Tab 1
11
10
NOTE: See descriptions of positions 1, 2, 3, 4, 5, 7, 8, and 9 in Figure 10 for additional details.
Figure 11. Read or Write LF Transponder (Type: MPT 16/17)
10
11
This is the 16/17-page 10-byte data (8-byte data with 2-byte CRC) of the LF Transponder MPT
16/17. Data appears after a successful transponder read.
The Lock column on the right side of the transponder data shows the lock status of every memory
block. To lock the transponder pages, check the Lock box of any page and click Write Tag (see the
description of position 11 for important details of writing to the tag).
Check the Calc CRC box to write 8-byte data (the CRC is calculated by the reader).
Uncheck the Calc CRC box to write 10-byte data (the CRC is not calculated by the reader).
Check this box and click Write Tag to write all pages of the MPT 16/17 transponder at one time.
Uncheck this box and click Write Tag to write only the edited page data. If the data has not been
edited, then reader writes the default page 1 data as shown in Figure 10.
SCBU050 – July 2012
Submit Documentation Feedback
MRD2EVM Microreader Evaluation Kit
Copyright © 2012, Texas Instruments Incorporated
11
Demo Examples
6.3
www.ti.com
Demo 3: HDX+ Transponder (Read or Write Memory) – Tab 1
12
13
NOTE: See descriptions of positions 1, 2, 3, 4, 5, 7, 8, and 9 in Figure 10 for additional details.
Figure 12. Read or Write Memory Content of HDX+ Transponder
12
13
12
This is the 16 page (64 byte) memory data of the HDX+-Transponder shown in grid view table
format. The description of each page is described in column 2 and the corresponding 4 byte data is
displayed in column 3, 4, 5 & 6 of the table as shown in table at position 12.
This is the last column of the grid view table that shows the memory status of each page. The
locked pages with orange background are not re-writable. The writable pages with green
background are re-writable.
MRD2EVM Microreader Evaluation Kit
SCBU050 – July 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Demo Examples
www.ti.com
6.4
Demo 4: OTP Transponder (Read or Write ID) – Tab 2
Figure 13. Read or Write ID of OTP Transponder
Click on Read ID (or) Write ID buttons to read (or) write the 64 byte ID with 16 byte CRC to an OTP
transponder.
This is the 10 byte data (8 byte ID and 2 byte CRC) of the OTP Transponder shown in grid view
table first row. The Lock column on the right side of the transponder data shows the lock stats of
the ID. To lock the transponder check the Lock box and click Write ID.
Decimal field for ISO 11785 animal or industrial code. This automatically converts to 8 byte hex
data in field 2. If hex data is entered in field 2, data automatically converts to decimal data in field 3.
Auto increment the ID after successful programming of a transponder.
Loads a list of IDs from an Excel® spreadsheet to write a batch of transponders. The Auto Inc ID
checkbox at position 4 needs to be checked to load the subsequent ID from the Excel spreadsheet
after each successful write to the transponder. Click Unload XLS to remove the loaded data.
SCBU050 – July 2012
Submit Documentation Feedback
MRD2EVM Microreader Evaluation Kit
Copyright © 2012, Texas Instruments Incorporated
13
Demo Examples
6.5
www.ti.com
Demo 5: HDX+ Transponder (Read or Write ID) – Tab 2
Figure 14. Read or Write ID of HDX+ Transponder
14
Read ID (or) Write ID button initiates a read (or) write of the 64 byte ID with 16 byte CRC of an
HDX+ transponder.
This is the 10 byte data (8 byte ID and 2 byte CRC) of the OTP HDX+ Transponder shown in the
grid view table first row. The Lock column on the right hand side of the transponder data shows the
lock stats of the ID. To lock the transponder check on the Lock checkbox and click on write ID
button.
Decimal field for ISO 11785 animal or industrial code. This automatically converts to 8 byte hex
data in field 2. If HEX data is entered in field 2, data automatically converts to decimal data in field
3.
Q-value of the transponder. Select the correct Q-value of the transponder and click Write ID to write
to the transponder.
Auto increment the ID after successful programming of a transponder.
Read or write the resonance frequency of a transponder. The frequency of a transponder is shown
in this field. To set the frequency at the same time of write ID phase, check the Set Frequency box
and type the target frequency in the field.
Loads a list of IDs from an Excel® spreadsheet to write a batch of transponders. The Auto Inc ID
checkbox at position 5 needs to be checked to load the subsequent ID from the Excel®
spreadsheet after each successful write to the transponder. Click Unload XLS to remove the loaded
data.
MRD2EVM Microreader Evaluation Kit
SCBU050 – July 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Demo Examples
www.ti.com
6.6
Demo 6: HDX+ Transponder (Trim Frequency) – Tab 2
Figure 15. Trim Resonance Frequency of HDX+ Transponder
Tune or read the frequency of transponder: Click Read Frequency to display the measured
frequency value at position 3 (the default target frequency value is displayed at position 2).
Target frequency field in Hz
Measured frequency value after each read/write.
A valid frequency (128000Hz to 140000Hz) needs to be entered in field 2, the frequency is then
programmed with the Write frequency button.
NOTE: Depending on transponder form factor, the tag needs to be separated from the
antenna by 20 mm to 40 mm to measure and program the correct frequency. The
resulting frequency might vary ±500 Hz due to the limited resolution of the internal
tuning circuit.
Status message field.
SCBU050 – July 2012
Submit Documentation Feedback
MRD2EVM Microreader Evaluation Kit
Copyright © 2012, Texas Instruments Incorporated
15
Demo Examples
6.7
www.ti.com
Demo 7: HDX+ Transponders (Inventory Command) – Tab 3
Figure 16. Read Inventory of HDX+ Transponder
16
Start inventory button: Reads AIDs of a group of advanced HDX+ transponders in the vicinity
region. The list of AIDs of transponders is shown at position 2 of Figure 10.
This is the 8 byte ID (8 byte AID) of the HDX+-Transponders detected and shown in each row of
grid view table. The Lock column on the right hand side of the transponder data shows the lock
status of the IDs.
A double click on any of ID data in the table initiates a read of the memory content of the selected
transponder.
MRD2EVM Microreader Evaluation Kit
SCBU050 – July 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Demo Examples
www.ti.com
6.8
Demo 8: PaLFI (Read, Write, Battery Charge and Check, and Flash LED) – Tab 4
Figure 17. Read, Write, Battery Charge, Battery Check, and Flash LED of PaLFI
Selection of page number and click on read/write page reads/writes the memory content of the
selected page.
The grid view table shows the 5 byte memory content of the selected page. The Lock field on the
right hand side of the memory data shows the lock status of the IDs.
Battery Check button: Battery voltage level check of PaLFI.
Battery charge status is indicated with 3 different colors orange (low voltage), yellow (medium
voltage) and green (high voltage).
Battery charge button: Charge PaLFI module.
Flash LED: Selection of the LED color in the field. A click on the flash LED button initiates the
corresponding LED to blink on PaLFI tag which is providing an example for an MSP access
command to the PaLFI tag.
SCBU050 – July 2012
Submit Documentation Feedback
MRD2EVM Microreader Evaluation Kit
Copyright © 2012, Texas Instruments Incorporated
17
MRD2EVM Microreader Evaluation Kit
Copyright © 2012, Texas Instruments Incorporated
CTB0308-1
CTB0308-2
10
11
12
13
14
15
CTB0308
CON3
10
11
12
13
14
15
default:closed
SJ1
GND
C4
default:closed
SJ2
GND
47uH
GND
R4
L1_PRINTED_INDUCTOR
330R
LED1
GREEN
SJ3
GND
R5
default:closed
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
S1
10k
R9
R7
ANT1
ANTCAP
18
ANT2
20
GNDP
VSP
USB_PUR
VSL
GND
CRD
WLS
USB_VBUS
OKT
STAT
GND
SIG_IN_1
SIG_IN_0
SIG_OUT_1
SIG_OUT_0
LF_RX
3_3V_OUT
USB_D+
USB_DTXD
RXD
RESETTEST/SBWTCK
RDENSYNC
IC2 MRDII DIL MODUL
10k
R8
SWS003
10k
15
14
13
12
11
10
330R
GND
GND
15
14
13
12
11
10
15
14
13
12
11
10
1 CON2
10p
10p
GND
C2
C1
GND
USB_DP
USB_DM
VBUS
GND
100n
C3
R2
27R
R3
LL103A
D1
27R
GND
TPD2E001DRLR
VCC
IO1
IO2
NC
GND
IC1
R1
GND
SHIELD1
SHIELD
GND
D+
D-
VBUS
CON1
RI-STU-MRD2 EVM Board
330R
7.1
LED2
RED
Schematics
R6
LED3
YELLOW
18
ON
Schematics
www.ti.com
Figure 18. RI-STU-MRD2 EVM Board Schematic
SCBU050 – July 2012
Submit Documentation Feedback
33k
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
【Important Notice for Users of this Product in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
http://www.tij.co.jp
【ご使用にあたっての注】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even
if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
General Texas Instruments High Voltage Evaluation Module (TI HV EVM) User Safety Guidelines
WARNING
Always follow TI's set-up and application instructions, including use of all interface components within their recommended electrical rated
voltage and power limits. Always use electrical safety precautions to help ensure your personal safety and the safety of those working
around you. Contact TI's Product Information Center http://support.ti.com for further information.
Save all warnings and instructions for future reference.
Failure to follow warnings and instructions may result in personal injury, property damage, or death due to electrical shock and
burn hazards.
The term TI HV EVM refers to an electronic device typically provided as an open framed, unenclosed printed circuit board assembly. It is
intended strictly for use in development laboratory environments, solely for qualified professional users having training, expertise and
knowledge of electrical safety risks in development and application of high voltage electrical circuits. Any other use and/or application are
strictly prohibited by Texas Instruments. If you are not suitable qualified, you should immediately stop further use of the TI HV EVM.
1.
2.
Work Area Safety:
(a)
Keep work area clean and orderly.
(b)
Qualified observer(s) must be present any time circuits are energized.
(c)
Effective barriers and signage must be present in the area where the TI HV EVM and its interface electronics are energized,
indicating operation of accessible high voltages may be present, for the purpose of protecting inadvertent access.
(d)
All interface circuits, power supplies, evaluation modules, instruments, meters, scopes, and other related apparatus used in a
development environment exceeding 50Vrms/75VDC must be electrically located within a protected Emergency Power Off
(EPO) protected power strip.
(e)
Use a stable and nonconductive work surface.
(f)
Use adequately insulated clamps and wires to attach measurement probes and instruments. No freehand testing whenever
possible.
Electrical Safety:
As a precautionary measure, it is always a good engineering practice to assume that the entire EVM may have fully accessible and
active high voltages.
(a)
De-energize the TI HV EVM and all its inputs, outputs, and electrical loads before performing any electrical or other diagnostic
measurements. Revalidate that TI HV EVM power has been safely de-energized.
(b)
With the EVM confirmed de-energized, proceed with required electrical circuit configurations, wiring, measurement equipment
hook-ups, and other application needs, while still assuming the EVM circuit and measuring instruments are electrically live.
(c)
Once EVM readiness is complete, energize the EVM as intended.
WARNING
While the EVM is energized, never touch the EVM or its electrical
circuits as they could be at high voltages capable of causing electrical
shock hazard.
3.
Personal Safety:
(a)
Wear personal protective equipment; for example, latex gloves or safety glasses with side shields or protect EVM in an
adequate lucent plastic box with interlocks from accidental touch.
Limitation for safe use: EVMs are not to be used as all or part of a production unit.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : Texas Instruments, Incorporated
Description                     : User's Guide
Title                           : MRD2EVM Microreader Evaluation Kit
Create Date                     : 2012:07:16 09:50:42-05:00
Creator Tool                    : TopLeaf 7.6.028
Modify Date                     : 2012:07:16 09:55:28-05:00
Metadata Date                   : 2012:07:16 09:55:28-05:00
Keywords                        : SCBU050,SCBU050
Producer                        : iText 2.1.7 by 1T3XT
Top Leaf-Profile                : draft
Top Leaf-Version                : Version=tlapi 7.6 28 2012/06/21 mailbox@turnkey.com.au Licence=tls05103
Document ID                     : uuid:f5c58ad6-f132-4d9e-90b2-49fb718cb53a
Instance ID                     : uuid:6846700a-63ed-462e-b504-fccdfad2522f
Page Mode                       : UseOutlines
Page Count                      : 22
PDF Version                     : 1.4
Author                          : Texas Instruments, Incorporated
Subject                         : User's Guide

EXIF Metadata provided by EXIF.tools