Texas Instruments 2541ARC The CC2541ARC is a development tool for the 2.4 GHz CC2541 BLE System-on-Chip from TI User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1889576
Application ID	XBGoitDp1EXrS2N9PyjVmA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	70.9kB (886224 bits)
Date Submitted	2013-01-29 00:00:00
Date Available	2013-01-30 00:00:00
Creation Date	2013-01-21 16:40:52
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2013-01-21 16:40:53
Document Title	user manual
Document Creator	Microsoft® Office Word 2007
Document Author:	Magnus Wines

SWRU???
January 2013
CC2541 Advanced Remote Control Quick Start Guide
Opening the Box and Evaluating Bluetooth® Low Energy
Kit Contents
Introduction
Hardware Setup
This document will guide you through the initial
steps required in order to run the pre programmed
Bluetooth® low energy (BLE) demo application.
Insert 3xAAA (LR03) batteries in the Advanced
Remote’s battery holder. You are good to go.
You will get familiar with the hardware in the box
and how to interface the remote with different
platforms.





1 x Advanced Remote
1 x CC2540USB Dongle
1 x CC Debugger/Programmer
3 x AAA Battery
Documentation
The RF Boards in this kit are FCC and IC certified
and tested to comply with ETSI/R&TTE over
temperature from 0 to +35°C.
Pressing any button on the remote will put it
into advertising mode and make it detectable by
Bluetooth Low Energy capable hosts.
1. Evaluate using dongle. A USB dongle
pre-programmed with firmware acting as
translator between BLE HID and USB
HID is supplied in the kit and works with
most operating system platforms.
2. Evaluate using Windows 8 native.
Windows 8 includes native support for the
BLE HID over GATT profile. Using a
BT4.0 dongle or internal BT4.0 hardware
you can easily connect the Advanced
Remote to your computer.
Caution! The kit contains ESD sensitive
components. Handle with care to prevent
permanent damage.
Connect Using Single Mode BT4.0 Low Energy CC2540USB HID Dongle
1. Insert dongle in USB port
2. Advertise and connect
3. Manage connection and bonds
The dongle will be enumerated as three USB
Human Interface Device class devices.
Press any number key or consumer control key to
make the device advertise.
Pressing SW1 on the dongle will disconnect any
active connection between the dongle and an
Advanced Remote.



Mouse
Keyboard
Consumer control
The LED on the dongle should start blinking red,
indicating it’s scanning for a Bluetooth Low
Energy peripheral which advertises BLE HID
service capabilities.
The devices will now connect and pair using
JustWorks pairing. The dongle LED should now
blink green when data is received from the
Advanced Remote and otherwise be off.
Long term bonding entries will be stored in both
the Advanced Remote and dongle to speed up
subsequent reconnections.
Pressing SW2 on the
dongle will erase all
long
term
bond
information stored on
the dongle.
Pressing this button
will not affect bond
data stored on the
Advanced Remote.
Connect to Windows 8 with BT 4.0 LE (Smart Ready) hardware
1. Make sure LE works
2. Open PC settings
3. Add Advanced Remote
In Device manager, under Bluetooth, make sure
that you see references to Bluetooth LE.
Move your mouse to the lower right hand corner
and click on Settings.
Then click on Devices and Add a device.
Then click on Change PC settings.
Web sites:
E2E Forum:
www.ti.com/ble
www.ti.com/ble-forum
4. Select and add the remote
5. Enter pairing code
6. Remove device
If you have pressed a button on the Advanced
Remote, and it’s not connected to another host, it
will show up in the list of found devices.
The devices will now pair using Passkey entry.
On your Advanced Remote, enter the 6-digit
passkey displayed on the computer screen.
A device can be removed from Windows and
bond data deleted by clicking on the device and
then the ( – ) symbol.
The Advanced Remote is now paired with
Windows and bond data is stored on both
devices, making reconnection faster and passkey
entry unnecessary.
Using the Advanced Remote Control
Mouse
keys
Mouse speed
Action keys
1. Advertise and connect
4. Mouse input
Almost all the keys will make the Advanced Remote
start advertising and be discoverable by hosts
scanning for HID capable BLE devices.
Holding down the middle button will prompt the Advanced
Remote to interpret your movement of the remote as mouse
input and send this to the computer.
2. Keyboard input
Double clicking the middle button will lock the mouse function.
The left and right buttons act as left and right mouse buttons.
Pressing any number will act as a keyboard input of
that number. The same goes for OK which is Enter,
Back which is Backspace and the four keys
surrounding OK, which act as directional or arrow
keys.
Pressing AV and –/– will decrease and increase mouse
speed.
3. Consumer control
Pressing the Red action button will remove bonding
information stored on the Advanced Remote. Pairing will have
to be done again, using passkey entry if applicable.
Buttons such as Volume, Mute, Play/Pause etc. are
consumer control keys, and will control media
settings on your computer.
5. Remove bond information
6. Calibrate
Pressing the Blue action button will force the Advanced
Remote to recalibrate the onboard gyroscope and
accelerometer used for motion sensing.
Additional Tools and Links
BLE Packet Sniffer
SmartRF Flash Programmer
IAR Embedded Workbench
The CC2540 USB Dongle can be used as a BLE
sniffer and monitor packets while the iPhone 4S
Demo is running.
Texas Instruments has a simple tool which can
be used to program and flash the CC2541.
To develop software, program, and debug the
CC2541, you should use IAR Embedded
Workbench for 8051.
The SmartRF Protocol Packet Sniffer software
can be downloaded at www.ti.com/packetsniffer.
SmartRF Flash Programmer can be downloaded
at www.ti.com/tool/flash-programmer.
More information on IAR EW8051, including a
free evaluation version download, can be found
at www.iar.com/ew8051.
BLE E2E Forum
BLE Wiki
Useful Links
For additional help, visit the TI Bluetooth low
energy E2E forum, www.ti.com/ble-forum, for
instant support during your development.
Our BLE Wiki contains application examples,
guides and documentation covering those extra
steps you might need help with. The Wiki is not
only managed by Texas Instruments employees
but also E2E community members. Anyone can
share, edit and make use of the information
posted here.
TI BLE Stack and Software:
www.ti.com/ble-stack
CC2540/41 Mini Development Kit User Guide:
www.ti.com/lit/swru270
CC2540/41 BLE Software Developer’s Guide:
www.ti.com/lit/swru271
The Wiki is found at www.ti.com/ble-wiki.
CC2540/41 User’s Guide:
www.ti.com/lit/swru191
CC2541 Product Page:
www.ti.com/cc2541
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from
all claims arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within
30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY
MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE
EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the
product. This notice contains important safety information about temperatures and voltages. For additional information on TI's
environmental and/or safety programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine,
process, or combination in which such TI products or services might be or are used. TI currently deals with a variety of customers
for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the
Federal Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING
DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end
product fit for general consumer use. It generates, uses, and can radiate radio frequency energy and has not been tested for
compliance with the limits of computing devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to
provide reasonable protection against radio frequency interference. Operation of the equipment may cause interference with
radio communications, in which case the user at his own expense will be required to take whatever measures may be
required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated
frequency and power limits. Any use of radio frequencies and/or power availability of this EVM and its development
application(s) must comply with local laws governing radio spectrum allocation and power limits for this evaluation module. It is
the user’s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power
limitations. Any exceptions to this are strictly prohibited and unauthorized by Texas Instruments unless user has obtained
appropriate experimental/development licenses from local regulatory authorities, which is responsibility of user including its
acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the
maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in
this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider
l’autorité de l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance
isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation
de l'émetteur.
【Important Notice for Users of this Product in Japan】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this
product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect
to this product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law
of Japan with respect to this product. Also, please do not transfer this product, unless you give the same notice above
to the transferee. Please note that if you could not follow the instructions above, you will be subject to penalties of
Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注意】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
( 1 ) 電波法施行規則第 6 条第 1 項第 1 号に基づく平成 18 年 3 月 28 日総務省告示第 173 号で定められた電波暗室等の試験設備
でご使用いただく。
( 2 ) 実験局の免許を取得後ご使用いただく。
( 3 ) 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a
finished electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility
evaluation in laboratory/development environments by technically qualified electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems and subsystems. It should
not be used as all or part of a finished end product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food
and Drug Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that
of your employees, affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other
applicable regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your
employees, affiliates, contractors or designees, using the EVM. Further, you are responsible to assure that any
interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation
and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage,
injury or death, even if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental
considerations per the user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output
voltage, current, power, and environmental ranges) may cause property damage, personal injury or death. If there are
questions concerning these ratings please contact a TI field representative prior to connecting interface electronics including
input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or
inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM
User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact
a TI field representative. During normal operation, some circuit components may have case temperatures greater than 60°C as
long as the input and output are maintained at a normal ambient operating temperature. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during
normal operation, please be aware that these devices may be very warm to the touch. As with all electronic evaluation tools,
only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development
environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their
representatives harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively,
"Claims") arising out of or in connection with any use of the EVM that is not in accordance with the terms of the agreement.
This obligation shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if the EVM
fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical
applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal
injury or death, such as devices which are classified as FDA Class III or similar classification, then you must specifically notify
TI of such intent and enter into a separate Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 6
XMP Toolkit                     : 3.1-701
Part                            : 1
Conformance                     : B
Producer                        : Microsoft® Office Word 2007
Creator Tool                    : Microsoft® Office Word 2007
Create Date                     : 2013:01:21 16:40:52+01:00
Modify Date                     : 2013:01:21 16:40:53+01:00
Creator                         : Magnus Wines
Author                          : Magnus Wines

EXIF Metadata provided by EXIF.tools