Texas Instruments ACS6410 Vicinity Card RFID Reader User Manual Installation Guide

Download:
Mirror Download [FCC.gov]
Document ID	296762
Application ID	Pox2AomnXuhnOK2BgXH2Ug==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	68.73kB (859069 bits)
Date Submitted	2003-01-17 00:00:00
Date Available	2003-01-17 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	www.adlibsys.com:ES3125-W2KA
Document Lastmod	2002-12-16 08:05:40
Document Title	Installation Guide
Document Creator	Microsoft Word 2000/2002
Document Author:	Randy Roebuck

* Information submitted for FCC, Industry
Canada, RTTE, CE & ETL certification:
A92ACS6410 &A92ACS6420 *
Specifications
Reader Model
S6410 Wall Plate
S6420 Mullion
Part number
RI-H4R-S6H3-00
RI-H4R-S5H3-00
Operating Frequency
S6410/S6420 Access Control Reader
Installation Guide
13.56 MHz
Supported Protocols
ISO/IEC 15693 (Vicinity)
9 - 14 VDC, built-in overvoltage
and reverse polarity protection
Supply Voltage
Power Consumption
90 mA Quiescent, 200 mA Read, 300 mA Max
RS-485 Baud Rates
Communication
Interface
Data Signal Integrity
9600, 19200, 38400 (Default)
Wiegand 26-64 bit and RS-485 protocol
Data Output Format
DES Encryption Mode (Cyper Text),
Wiegand UID Mode, Wiegand ASCII mode
500 feet Wiegand, 4000 feet RS-485
Operating Temperature
-20°C to +70°C
Storage Temperature
-40°C to +85°C
Humidity
90% RH at 70°C
Protection Class
Regulatory Approvals
Overall Dimensions
Weight
IP64, Potted
FCC, R&TTE (CE), UL-94 and UL-294 (ETL)
5.0” x 5.0” x 1.0”
(12.7 x 12.7 x 2.5 cm)
5.0” x 1.7” x 1.0”
(12.7 x 4.3 x 2.5 cm)
~8.5 oz (~241 g)
~4.8 oz (~136 g)
Complete warranty information can be found on the website at:
www.ti-rfid.com
© Copyright Texas Instruments. 2002
All rights reserved.
11-06-21-713 09/02
Packing List
Before You Begin
This package includes:
Qty.
Description
S6410 or S6420 Reader with back plate
#6 Phillips-head machine mounting screws
#6 Phillips-head self-tapping mounting screws
Phillips-head cover screw
Security-head cover screw
Installation guide (this sheet)
If any items are missing from the package, please contact the
appropriate technical support agent:
1-888-937-6536 or
USA
1 (972)-575-4364
Determine the installation method, which parts are needed, and
which wires will be used. These instructions assume that the unit
is being installed on an unprepared flat surface. If this unit is to be
installed in an electrical box or door mullion opening, skip to step
3 of the installation instructions.
Typical Installation
1.
2.
Belgium (English)
+32 (0)2 7455455
3.
France (English)
+33 4 93 22 22 00
4.
Germany
+49 (0)8161 80 2200
Italy
+39 (0)39 6568 210
Netherlands (English)
+31 (0)546 879 222
Spain
+34 902 19 73 96
Sweden (English)
+46 (0)8 58755527
UK
or visit us at: www.ti-rfid.com
+44 (0)1604 88 4088
5.
6.
7.
8.
Use appropriate template (from back) to mark hole locations
for wire and screws. A set of self-tapping screws is included,
however the holes may be pre-drilled if desired.
Drill a 3/4” (20 mm) maximum diameter hole for wire to pass
through. Placement of this hole is arbitrary, but it must align
with the opening of the back plate.
Slide wiring cable through mounting plate prior to connecting
wires. Be sure the flat side of the plate is toward the wall.
Connect wires per the wire guide. Cap any unused wires to
prevent shorting.
Screw mounting plate onto surface using the appropriate
screws provided.
Attach the housing to the mounting plate by inserting the
upper tab(s) of the housing into the slots in the plate.
Secure the front housing using either the included securityhead cover screw or the Phillips-head cover screw.
Test unit for proper functionality. This can be accomplished
by bringing a card into the read field with power applied to the
reader. The LED’s and audio should function as desired.
Note that this test can only be performed when the unit is in
it’s default (Wiegand) mode as shipped.
* Information submitted for FCC, Industry Canada, RTTE, CE
& ETL certification: A92ACS6410, A92ACS6420 *
Determining Which Wires Will Be Used
Mounting
The following wire connections are essential for proper
functionality in RS-485 or Wiegand mode.
Wiegand Mode
Black Ground
Red
Power
Green Data (0)
White Data (1)
RS-485 Mode
Black
Ground
Red
Power
Gray
Data (A or -)
Violet
Data (B or +)
The remaining wires may be connected as desired to customize
functionality of the audio and LED indicators. See the S6400
User’s Guide (11-06-21-711) for more information regarding the
use of these wires.
Complete Wire Guide
Color
Black
Red
Gray
Violet
Green
White
Brown
Orange
Yellow
Blue
Function
Ground (GND)
Power (9-14 VDC)
RS-485(A or -)
RS-485(B or +)
Wiegand Data(0)
Wiegand Data(1)
Red LED
Green LED
Audio
Hold
Note: Optimum read range can be achieved by pushing excess
wire through opening in wall. Wire accumulated inside reader
housing may cause read range to diminish.
Allow 1" (25 mm) min.
for reader cover
UP
UP
2 1/8"
(54 mm)
2 3/8"
(60 mm)
3 5/16"
(84 mm)
2 1/2" min.
(63 mm)
Optimum location for
cable entry hole.
3/4" (20 mm) MAX
2 1/2" min.
(63 mm)
Wall Plate Template
7/8" min.
(22 mm)
7/8" min.
(22 mm)
Mullion Template

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Title                           :  Installation Guide
Producer                        : www.adlibsys.com:ES3125-W2KA
Version                         : Version 2.06a Pro - Developer Licence # 44B65203-B23E
Create Date                     : 9/12/2002 10:30:12
Modify Date                     : 2002:12:16 08:05:40-06:00
Author                          : Randy Roebuck
Creator                         : Microsoft Word 2000/2002
Page Count                      : 2
Has XFA                         : No

EXIF Metadata provided by EXIF.tools