Texas Pci445X Users Manual PC Card And 1394 OHCI Link Controller Implementation Guide
Texas-Instruments-Pci445X-Users-Manual-400209 texas-instruments-pci445x-users-manual-400209
PCI445X to the manual 5512d998-0a69-482b-90e9-a98ea45270d5
2015-02-04
: Texas Texas-Pci445X-Users-Manual-390411 texas-pci445x-users-manual-390411 texas pdf
Open the PDF directly: View PDF 
.
Page Count: 46
| Download | |
| Open PDF In Browser | View PDF |
Implementation
Guide
August 2000
PCI Bus Solutions
SCPU007
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
Notational Conventions
Preface
Read This First
About This Manual
This manual is intended to assist the designer who is attempting to implement
a solution using the PCI4450 or PCI4451. Much, but not all, of the information
contained herein can also be found elsewhere. However, the smaller size of
this manual, as well as its organization by topics of primary interest to the
hardware designer, make it a much more usable source regarding those
problems most likely to be encountered in the design process.
How to Use This Manual
This document contains the following chapters:
Chapter 1, PCI445X Device, provides the designer with information and
examples beyond that contained in the data manuals, which will be useful for
implementing solutions using the PCI4450 or PCI4451.
Appendix A, Global Reset Only Bits, PME Context Bits contains tabular listings
of those register bits that can only be cleared by a global reset, and of those
register bits used in conjunction with power management events.
Appendix B, PME and RI Behavior, provides truth tables that explain events
and conditions which can wake up a device that has been placed in partially
functional state for power conservation.
Appendix C, PCI445X Buffer Types, lists the type of signal buffering used for
input and/or output on each terminal of the device.
Notational Conventions
This document uses the following conventions.
Program listings, program examples, and interactive displays are shown
in a special typeface similar to a typewriter’s. Examples use a bold
version of the special typeface for emphasis; interactive displays use a
bold version of the special typeface to distinguish commands that you
iii
Contents
enter from items that the system displays (such as prompts, command
output, error messages, etc.).
Here is a sample program listing:
0011
0012
0013
0014
0005
0005
0005
0006
0001
0003
0006
.field
.field
.field
.even
1, 2
3, 4
6, 3
Here is an example of a system prompt and a command that you might
enter:
C:
csr –a /user/ti/simuboard/utilities
In syntax descriptions, the instruction, command, or directive is in a bold
typeface font and parameters are in an italic typeface. Portions of a syntax
that are in bold should be entered as shown; portions of a syntax that are
in italics describe the type of information that should be entered. Here is
an example of a directive syntax:
.asect “section name”, address
.asect is the directive. This directive has two parameters, indicated by
section name and address. When you use .asect, the first parameter must
be an actual section name, enclosed in double quotes; the second
parameter must be an address.
Square brackets ( [ and ] ) identify an optional parameter. If you use an
optional parameter, you specify the information within the brackets; you
don’t enter the brackets themselves. Here’s an example of an instruction
that has an optional parameter:
LALK 16–bit constant [, shift]
The LALK instruction has two parameters. The first parameter, 16-bit
constant, is required. The second parameter, shift, is optional. As this
syntax shows, if you use the optional second parameter, you must
precede it with a comma.
Square brackets are also used as part of the pathname specification for
VMS pathnames; in this case, the brackets are actually part of the pathname (they are not optional).
Braces ( { and } ) indicate a list. The symbol | (read as or) separates items
within the list. Here’s an example of a list:
{ * | *+ | *– }
This provides three choices: *, *+, or *–.
Unless the list is enclosed in square brackets, you must choose one item
from the list.
Some directives can have a varying number of parameters. For example,
the .byte directive can have up to 100 parameters. The syntax for this
directive is:
.byte value1 [, ... , valuen ]
iv
Trademarks
This syntax shows that .byte must have at least one value parameter, but
you have the option of supplying additional value parameters, separated
by commas.
Related Documentation From Texas Instruments
PCI4450 GFN/GJG PC Card and OHCI Controller Data Sheet, SCPS046
PCI4451 GFN/GJG PC Card and OHCI Controller Data Manual, SCPS054
OHCI.Lynx Configuration Information Application Report, SLLA077
PHY Layout Recommendations Application Report, SLLA020A
TSB41LV03A Data Sheet, SLLS364
http://www.ti.com/sc/1394
http://www.ti.com/sc/docs/apps/analog/1394_physical_layer_controllers.html
FCC Warning
This equipment is intended for use in a laboratory test environment only. It
generates, uses, and can radiate radio frequency energy and has not been
tested for compliance with the limits of computing devices pursuant to subpart
J of part 15 of FCC rules, which are designed to provide reasonable protection
against radio frequency interference. Operation of this equipment in other
environments may cause interference with radio communications, in which
case the user at his own expense will be required to take whatever measures
may be required to correct this interference.
Trademarks
MicroStar BGA is a trademark of Texas Instruments.
TI is a trademark of Texas Instruments.
Windows is a registered trademark of Microsoft Corporation. (Windows 95, Windows)
v
vi
Contents
Contents
1
PCI445X Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.1
System Features Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.1 Package Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.2 G_RST and PRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.3 PME and RI Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.4 ZV Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.5 EEPROM for Subsystem Vendor and Subsystem ID Registers . . . . . . . . . . . . 1-3
1.1.6 PCI and ISA Style Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.1.7 Socket Power Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.1.8 Distributed DMA (DDMA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.1.9 Optional PCI Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.1.10 Socket Activity LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.1.11 MFUNC7–MFUNC0 Terminal Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.1.12 Miscellaneous Functions Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.2
System Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.2.1 Clamping Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.2.2 PCI Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.2.3 PC Card Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
1.2.4 2-Wire (I2C) Interface for EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
1.3
Sample PCI445X EEPROM Data File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
1.3.1 P2C Interface for TPS22x6 Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
1.3.2 Zoomed Video (ZV) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
1.3.3 Interrupt Signaling Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
1.3.4 Miscellaneous Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
1.3.5 Requirement of Pullup/Pulldown Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
1.4
BIOS Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
1.4.1 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
1.4.2 System Sleeping State Consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
1.4.3 Docking System Consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
1.5
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.5.1 G_RST Clamping Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.5.2 PME/RI_OUT Bit Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.5.3 Serialized IRQ Data Stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.5.4 Socket Power Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.5.5 External CLOCK Frequency for P2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
vii
Contents
A
Global Reset Only Bits, PME Context Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
A.1 Global Reset Only Bits/PME Context Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
B
PME and RI Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
B.1 PME and RI Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
C
PCI445X Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
C.1 PCI445X Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
viii
Contents
Figures
1–1
1–2
1–3
1–4
1–5
1–6
1–7
Typical System Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Serialized Interrupt Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
EEPROM 2-Wire Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
TPS22X6 Power Switch Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Example of a ZV Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Distributed DMA Signal Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
G_RST and VCCP Relationship . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
ix
Contents
Tables
1–1
1–2
1–3
1–4
1–5
A–1
A–2
B–1
B–2
C–1
C–2
x
Registers and Bits Loadable Through Serial EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
PC Card Interface Pullup Register List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
PCI Bus Interface Pullup Register List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Miscellaneous Terminals Pullup Register List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Required Pullup/Pulldown Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
Global Reset Only Cleared Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
PME Context Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
CardBus CTSCHG and Wake-Up Signals Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
16-Bit Card RI/STSCHG and Wake-Up Signals Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . B-2
PCI445X Terminal Function Assignment and Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Buffer Type Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7
Chapter 1
PCI445X Device
This implementation guide assists platform hardware developers designing
with the PCI445X dual socket PC card and 1394 open host controller interface
(OHCI) link layer controller (LLC). The PCI445X designation refers to any
device in the PCI445X family, for example, the PCI4450 or PCI4451 device.
The document includes an overview of the PCI445X function and features,
terminal assignments and pinout illustrations, PCI445X I/O electrical
characteristics, identification of required passive components and
recommendations for system implementation, and PHY/Link interface signal
isolation considerations.
Advantages of the PCI445X device:
G_RST (Section 1.1.2)
Internal ring oscillator (Section 1.3.1)
Zoomed video auto-detect function (Sections 1.1.4, 1.3.2)
Integrated IEEE1394 OHCI link layer controller
Topic
Page
1.1
System Features Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.2
System Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.3
Sample PCI445X EEPROM Data File . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
1.4
BIOS Consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
1.5
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1-1
Figure 1–1 illustrates a platform using the PCI445X device along with the
TSB41LV03 3-port PHY, which provides the necessary interface to implement
a 3-port IEEE1394 node.
Figure 1–1. Typical System Architecture
North
Bridge
CPU
Memory
PCI Bus
South
Bridge
Sound
Controller
Graphics
Controller
Audio
Codec
19
PCI445X
ZV
4
PC Card
Power
Switch
14
2
Interrupt / PME / RI
TSB41LV03A
PHY
1-2
Socket
Power
EEPROM
System Features Selection
1.1 System Features Selection
This section explains selectable system features. Feature selection is required
for GPIO and MFUNC terminal assignments and PCI445X register
initialization. Detailed system implementation methods are described in the
following sections. All functions cannot necessarily be used at the same time,
because of the limitations of programmable multifunction terminals (i.e.,
MFUNC7–MFUNC0).
1.1.1
Package Types
The Texas Instruments PCI445X device is offered in two package types:
256-terminal ball grid array (BGA) and 257-terminal MicroStar BGA.
MicroStar BGA is a type of chip scale packaging (CSP).
1.1.2
G_RST and PRST
The PCI445X device has two reset inputs, G_RST and PRST. G_RST resets
all registers and state-machines; PRST resets registers that are not required
to maintain context in a low power state (see Table A–1 and Table A–2). If the
system does not support a wake-up event from D3-state (hot or cold), then
these terminals can be tied together.
1.1.3
PME and RI Signaling
For supporting a wake-up event, a power management event (PME) and/or
an RI signal should be signaled to the system. PME is available only on the
RI_OUT/PME terminal. RI_OUT is available on RI_OUT/PME or MFUNC7.
PME and RI_OUT signals are usually connected to the south bridge or
embedded controller (EC). Detailed PME and RI signal behavior is explained
later.
1.1.4
ZV Support
The PCI445X device has internal zoomed video (ZV) buffers. It can support
three ZV sources, from two PC cards and one external source. Refer to the
detailed implementation guide in Section 1.3.2. The PCI445X device has the
ZV autodetect function for supporting a third external zoomed video source.
ZVSTAT and ZVPCLK are required to support the third source. (The ZV
autodetect function needs ZVPCLK for input, and ZVSTAT for enabling.)
ZVSTAT can be assigned on the MFUNC0, MFUNC1, or MFUNC4 terminal.
1.1.5
EEPROM for Subsystem Vendor and Subsystem ID Registers
Subsystem vendor ID and subsystem ID registers (PCI offsets 40h and 42h)
can be loaded from EEPROM through a two-wire serial interface. These
registers can be configured by BIOS if the PCI445X device is implemented on
the motherboard, by setting the SUBSYSRW bit (system control register, PCI
offset 80h, bit 5). EEPROM may be required for docking systems and is
required for add-in cards. The EEPROM interface terminals SDA and SCL are
PCI445X Device
1-3
System Features Selection
automatically assigned on the dedicated SDA and SCL terminals. A pullup
resistor (typically 10 kΩ) must be added on SDA and SCL when using an
EEPROM. The value of the pullup resistor can vary for different EEPROMs.
Refer to the EEPROM data sheet or contact the manufacturer for the
recommended pullup resistor value.
1.1.6
PCI and ISA Style Interrupt
The PCI445X device provides three modes of interrupt signaling:
Parallel PCI interrupts only
Parallel PCI interrupts and serialized ISA interrupts
Serialized PCI interrupts and serialized ISA interrupts
Three PCI interrupts (INTA, INTB, and INTC) may be used and signaled in
either the parallel mode using the MFUNC terminals or in the serial mode. The
number of PCI interrupts may be reduced by setting the INTRTIE bit (system
control register, PCI offset 80h, bit 29), which allows both the CardBus
functions (function 0 and function 1) to report and use INTA or by setting the
TIEALL bit (system control register, PCI offset 80h, bit 28) which allows all 3
functions (both CardBus + OHCI) to report and use INTA.
1.1.7
Socket Power Switches
The PCI445X device supports TPS2206 and TPS2216 power switches. Refer
to the detailed explanation on each data sheet. The interface between the
power switch and the PCI445X device is serialized, so an external or internal
clock source is required. By default an external power switch clock is assumed
but this can be changed to use the oscillator internal to the PCI445X device
by setting P2CCLK bit (system control register, PCI offset 80h, bit 27).
1.1.8
Distributed DMA (DDMA)
Most of the systems do not use this function. This function needs PCGNT and
PCREQ signals. PCGNT can be assigned to the MFUNC2 or MFUNC3
terminal. PCREQ can be assigned to the MFUNC0, MFUNC4, or MFUNC7
terminal. (See Section 1.3.4.5, Distributed DMA.)
1.1.9
1.1.9.1
Optional PCI Signals
CLKRUN
CLKRUN is the primary method for power reduction on the PCI bus. Most of
the notebook PCs implement CLKRUN. The PCI445X device has a dedicated
CLKRUN terminal. If it is not used, then a pulldown resistor is required to
prevent oscillations on this input.
1.1.9.2
LOCK
This signal can be assigned on the MFUNC1, MFUNC3 or MFUNC7 terminal.
1-4
System Features Selection
1.1.10 Socket Activity LEDs
Socket activity signals can be assigned on MFUNC4 (slot 1), MFUNC3 (slot 2),
MFUNC5 (OHCI_LED), MFUNC6 (OHCI_LED), and MFUNC7 (OHCI_LED).
1.1.11 MFUNC7–MFUNC0 Terminal Assignments
After selecting required functions for the system, multifunction terminals
MFUNC7–MFUNC0 are ready to be assigned. Texas Instruments offers
Windows-based software, named TIROUTE.EXE, to assist with terminal
assignment.
1.1.12 Miscellaneous Functions Description
1.1.12.1 Serialized Interrupt Control
Serialized interrupt signaling is described below.
Figure 1–2. Serialized Interrupt Signal
PCLK
IRQSER
START Frame
IRQ0
IRQ1
SMI
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ10
IRQ11
IRQ12
PCLK
IRQSER
IRQ13
IRQ14
IRQ15 IOCHCK
INTA
INTB
INTC
INTD
STOP Frame
The start frame width may vary from four to eight PCI clock cycles. The STOP
frame width is two clock cycles for quiet mode and three clock cycles for
continuous mode. Default mode is continuous mode for all slave devices and
a host device. PIIX4 does not support IRQ0, IRQ8, and IRQ13.
The PCI445X can generate serial IRQ frames for ISA and PCI interrupts.
Below are related registers and their definitions.
INTMODE bits (device control register, PCI offset 92h, bits 2–1). Select
interrupt mode
SER_STEP bits (system control register, PCI offset 80h, bits 31–30).
Change PCI interrupt data frame (serial interrupts only)
INTRTIE bit (system control register, PCI offset 80h, bit 29). Tie CardBus
PCI interrupts to INTA
TIEALL bit (system control register, PCI offset 80h, bit 28). Tie all PCI
interrupts internally
Refer to the Serialized IRQ Support for PCI Systems specification,
revision 6.0.
1.1.12.2 CSC Interrupt Routing for Windows Compatibility
The CSC interrupt routing control bit (diagnostic register, PCI offset 93h, bit 5)
should be set to 1 (default) to keep Windows compatibility.
PCI445X Device
1-5
System Features Selection
1.1.12.3 Asynchronous CSC Interrupt Generation
The ASYNC_CSC bit (diagnostic register, PCI offset 93h, bit 0) controls the
CSC interrupt signaling method. If this bit is set to 0, then CSC is generated
synchronously to PCLK (recommended). By default this bit is set to 1, which
is the asynchronous mode.
1.1.12.4 CardBus Reserved Terminal Signaling
The CardBus interface has reserved terminals. Usually the CardBus controller
drives these terminals low. If the CBRSVD bit (system control register, PCI
offset 80h, bit 22) is set to 0, then the CardBus reserved terminal signals are
in a high-impedance state when a CardBus card is inserted in the socket.
1.1.12.5 Memory Burst R/W Operation Control
Memory read bursting is controlled via the MRBURSTDN bit (system control
register, PCI offset 80h, bit 15) for downstream burst transactions (PCI-to-PC
Card) and the MRBURSTUP bit (system control register, PCI offset 80h,
bit 14) for upstream burst transactions (PC Card-to-PCI). Memory write
bursting is controlled via the POSTEN bit (bridge control register, PCI offset
3Eh, bit 10). This bit enables write posting if disabled. No write data can be
accepted (including burst writes) until any previous write data has been
forwarded to its destination. By default, write posting and upstream read bursts
are disabled.
1.1.12.6 Power Savings Mode
The PCI445X device has a proprietary power-saving mode. It can be disabled
by changing the PWRSAVINGS bit (system control register, PCI offset 80h,
bit 6) to 0. When this bit is enabled (default), PCI CLOCK is internally gated
for a nonfunctioning circuit. For example, the CardBus interface does not
function when a 16-bit card is inserted. This power-saving mode will not
degrade performance; therefore, the default setting is recommended.
1.1.12.7 PME/RI_OUT Terminal Control Clarification
PME/RI_OUT terminal can be set up to signal a combination of these events.
The terminal is set up using the PME/RI_OUT bit (system control register, PCI
offset 80h, bit 0), the RIENB bit (card control register, PCI offset 91h, bit 7), and
PME enable bit (power management control/status, PCI offset A4h, bit 8). If
the terminal is set up as RI_OUT and RIENB has ring indicate enabled, then
this signal follows the RI_OUT signal for 16-bit I/O cards. If RIENB has ring
indicate disabled but PME has PME enabled, then this line reflects the state
of the PMESTAT bit (power management control/status, PCI offset A4h,
bit 15). If both PME and ring indicate are disabled, then the line remains high.
If the line is configured as PME and PME is enabled, then this line follows the
state of the PMESTAT bit; otherwise, the line remains high.
1.1.12.8 CLKRUN Control
PCLK can be kept running using CLKRUN protocol by setting the KEEPCLK
bit (system control register, PCI offset 80h, bit 1) to 1.
1-6
System Features Selection
CCLK can be slowed down rather than stopped by CCLKRUN. If CCLKRUN
is set, the CLKCTRLEN (CardBus socket 20h, bit 16) and CLKCTR (CardBus
socket 20h, bit 0) bits are both set to 1. The clock is slowed down to 1/16. In
this mode the PCI clock is not allowed to stop.
1.1.12.9 SMI
A PC card power change event can be reported to the system as SMI (IRQ2
or CSC). It can be controlled with the SMIROUTE, SMISTATUS, and SMIENB
bits (system control register, PCI offset 80h, bits 26, 25, and 24, respectively).
1.1.12.10 Socket Power Lock
Socket power can be protected from software control in the D3hot state. It can
be done with the socket power lock bit (device control register, PCI offset 92h,
bit 7).
1.1.12.11VCC Protection
The VCCPROT bit (system control register, PCI offset 80h, bit 21) controls VCC
protection for 16-bit cards. This feature protects applying the wrong (higher)
VCC to the 16-bit card. If a 3.3-V-only card is inserted, then it protects against
applying 5 V to the card. Default is 0 (enabled).
1.1.12.12 ZV Port Control and Auto Detect Function
Internal zoomed video buffers can be controlled with the ZV autodetect
function. It can be turned on by setting the zoomed video autodetect bit
(multimedia control register, PCI offset 84h, bit 5) to 1. Autodetect priority
encoding bits (multimedia control register, PCI offset 84h, bits 4–2) can control
the priority scheme.
PCI445X Device
1-7
System Implementation
1.2 System Implementation
This section describes signal connection for each interface, PCI bus, PC card
interface, I2C interface, P2C interface, ZV interface, interrupt interface (parallel
and serial), miscellaneous signals, and the PHY-Link interface. It also explains
pullup/pulldown resistor requirements.
1.2.1
Clamping Rails
The PCI445X device has three clamping rails: VCCA, VCCB, and VCCP. VCCA
and VCCB are not power supplies for PC cards. After a card is powered up, the
supply voltage to the card is fed back into the VCCA (or VCCB) input to the
controller. This provides the controller a clamping level for signals to the card.
Technically the power switch controlling VCCA is also supplying power to the
card via this signal, but actually VCCA is not a signal via which the controller
supplies power to the card.
The PCI445X device only drives out a maximum signal of 3.3 V due to the
3.3-V core. This is not a problem, as 3.3 V is still seen as a logic 1 to a 5-V
system.
VCCA and VCCB
PC Card interface clamping rails. CD1, CD2, VS1, VS2, and STSCHG/RI
are not clamped, because these terminals should be able to signal without
VCCA/VCCB.
VCCP
PCI bus interface clamping rail. It includes the MFUNC7/LOCK,
MFUNC7–MFUNC0, IRQSER, GRST, and P2C terminals. It excludes
INTA, INTB, INTC, and PME.
Note:
The PME/RI_OUT terminal uses an open drain (OD) buffer.
1.2.2
PCI Bus Interface
PCLK, AD31–AD0, C/BE3–C/BE0, PAR, DEVSEL, FRAME, STOP,
TRDY, IRDY, GNT, REQ
These terminals can be connected to the system PCI bus directly. GNT
and REQ are dedicated signals from the PCI bus arbitrator.
PERR, SERR, and LOCK
PERR and SERR are required signals. LOCK is an optional signal and
available in MFUNC1, MFUNC3, and MFUNC7.
IDSEL
If there is a pulldown on LATCH, then the IDSEL will be routed to AD23, but
the consequence of this is that the system designer must use AD23 as
1-8
System Implementation
IDSEL, there is no alternative. If another AD line is to be used for IDSEL,
then the system designer must leave the pullup off LATCH and use
MFUNC7 to route IDSEL. Also, if AD23 is used, then the resistive coupling
should not be used.
Refer to the Implementation Note: System Generation of IDSEL in the PCI
Local Bus Specification, Revision 2.2 (section 3.2.2.3.5). PCI Local Bus
Specification, Revision 2.2 (section 4.2.6, footnote 31) recommends
resistive coupling. A 100-Ω resistor is recommended.
PRST (PCI reset) and G_RST (Global reset)
G_RST initializes all of the registers and state-machines of the PCI445X
device, and PRST does not. G_RST should be asserted during power-on
and rebooting. It puts the PCI445X device into the initialized state. PRST
does not initialize global-reset-only bits and, if PME is enabled, PME
context bits. Refer to Table A–1, Global Reset Only Cleared Bits, and
Table A–2, PME Context Bits. PRST is connected to PCI RESET; G_RST
requires a special signal in the motherboard. It will come from the chipset.
If the system does not support wake-up from D3cold, then PRST and
G_RST can be tied together. Note that G_RST and PRST are clamped to
VCCP.
INTA, INTB, and INTC
When using one of the parallel PCI interrupt modes, INTA, INTB, and INTC
should be connected to the PCI interrupt lines. If the INTRTIE bit (system
control register, PCI offset 80h, bit 29) is set, then both CardBus functions
(functions 0 and 1) will signal and report INTA, and only INTA and INTC will
need to be routed. If the TIEALL bit (system control register, PCI offset
80h, bit 28) is set, then all functions (0, 1, and 2) will report INTA and INTA
will be the only interrupt required.
CLKRUN
This signal is optional. However, if saving power is a concern, this signal
should be implemented. Refer to the PCI Mobile Design Guide
Revision 1.1 (Section 2).
PME
This signal is required for the ACPI systems. In a notebook PC, this signal
is usually connected to the south bridge (ex., PIIX4) or embedded
controller (EC). The PME terminal uses an open-drain type buffer.
Note: Pullup Resistor Requirements
A pullup resistor is required for each of the following terminals: IRDY, TRDY,
FRAME, STOP, DEVSEL, PERR, SERR, LOCK, PRST, G_RST, INTA, INTB,
INTC, CLKRUN, and PME.
PCI445X Device
1-9
System Implementation
1.2.3
PC Card Interface
The PC Card interface has two modes: the 16-bit interface mode and the
CardBus 32-bit interface mode.
Damping resistor on CCLK terminal
A series-damping resistor is recommended on the CCLK signal. The
damping resistor is system dependent. If line impedance is in the 60 – 90-Ω
range, a 47-Ω resistor is recommended (see PC Card Standard,
Revision 7).
CD line filtering
PCI445X device has the advanced CDx line filtering circuit. It provides
90 µs of noise immunity. A 270-pF filtering capacitor is still recommended
for each of the power supply terminals: VCC, VCCS, and VCCP.
Socket power supply
Socket power is supplied through TPS22X6 power switches. The
PCI445X device requires VCCA and VCCB for the protection of the other
device(s) on the bus.
1.2.4
2-Wire (I2C) Interface for EEPROM
The PCI445X device can load configuration registers from EEPROM after
G_RST assertion. The SDA and SCL lines require pullup resistors to enable
this function. Depending on the EEPROM requirements, the SDA and SCL
lines must be pulled up to 3.3 V or 5 V.
Figure 1–3. EEPROM 2-Wire Interface
EEPROM
SDA
PCI445X
TPS22X6
SCL
EEPROM slave address should be 101 0000b.
1-10
System Implementation
Table 1–1. Registers and Bits Loadable Through Serial EEPROM
Register Offset
Register
Bits Loaded From
EEPROM
The following are configuration registers for the OHCI function (function 2)
PCI register (2Ch)
PCI subsystem ID
15–0
PCI register (2Dh)
PCI vendor ID
15–0
PCI register (3Eh)
PCI maximum latency, minimum grant
PCI register (F0h)
PCI miscellaneous configuration
PCI register (F4h)
Link enhancements control
7, 2, 1
OHCI register (24h)
1394 global unique ID Hi
31–0
OHCI register (28h)
1394 global unique ID Lo
31–0
11–8, 3–0
15, 13, 10, 3–0
The following are configuration registers for PC Card functions (functions 0 and 1)
PCI register (40h)
Subsystem vendor ID
15–0
PCI register (42h)
Subsystem ID
15–0
PCI register (80h)
System control
31–24, 22–14, 6–3, 1, 0
PCI register (86h)
General control
3–0
PCI register (89h)
General-purpose event enable
PCI register (8Bh)
General-purpose output
PCI register (8Ch)
Multifunction routing
PCI register (91h)
Card control
7, 6, 2–0
PCI register (92h)
Device control
7, 6, 2–0
PCI register (93h)
Diagnostic
PCI register (A2h)
Power management capabilities
15
PCI register
ExCA ID and revision
7–0
7, 6, 3–0
3–0
30–28, 26–24, 22–20,
18–16, 14–12, 10–8,
6–4, 2–0
7, 5, 0
PCI445X Device
1-11
System Implementation
1.3 Sample PCI445X EEPROM Data File
Following is an example EEPROM data file used with the PCI445X device:
;PCI4450 default EEPROM Data File
;Register
0xXX
Binary
Description
;––––––––
––––
––––––
–––––––––––
00
0x43
;01000011
PCI max_lat (lower
4 bits)/PCI min gnt (lower 4 bits)
01
0x4C
;01001100
PCI Subsystem Vendor ID (lsbyte) ** Insert
02
0x10
your SSVID MSB
;00010000
PCI Subsystem Vendor ID (msbyte) ** Insert
03
0x11
your SSID LSB
;00010001
PCI Subsystem ID (lsbyte)
** Insert
04
0x80
your SSID MSB
;10000000
PCI Subsystem ID (Msbyte)
** Insert
05
defaults
0xC2
;11000010
Link
06
0x40
;01000000
MiniROM_Addr
07
008
109
20A
30B
incremented
0x56 ;01010110
0x28 ;00101000
0x00 ;00000000
0x08 ;00001000
0xXX ;XXXXXXXX
from ;serial.dat
your SSVID LSB
1394
1394
1394
1394
1394
Enhancement
GUIDHi
GUIDHi
GUIDHi
GUIDHi
GUIDLo
Register/HC
(lsbyte)**
(lsbyte)**
(msbyte)**
(msbyte)**
(lsbyte)**
Control
Insert GUIDHi
Insert GUIDHi
Insert GUIDHi
Insert GUIDHi
GUIDLo byte 0
byte
byte
byte
byte
auto
0C
0xXX ;XXXXXXXX
incremented from ;serial.dat
1394 GUIDLo (lsbyte)** GUIDLo byte 1
auto
0D
0xXX ;XXXXXXXX
incremented from ;serial.dat
1394 GUIDLo (msbyte)** GUIDLo byte 2
auto
0E
0xXX ;XXXXXXXX
incremented from ;serial.dat
1394 GUIDLo (msbyte)** GUIDLo byte 3
auto
0F
0xXX
;XXXXXXXX
10
0x10
;00010000
11
0x00
;00000000
PCI Misc Byte 0
12
0x24
;00100100
PCI Misc Byte 1
13
0xFF
;11111111
this area reserved
19
0xFF
;11111111
1A
0xFF
;11111111
1B
0xFF
;11111111
1C
0xFF
;11111111
1-12
ROM CRC
(Calculated by EELynx)
Link_Enh Byte 1
System Implementation
1D
0xFF
;11111111
1E
0xFF
;11111111
1F
0xFF
;11111111
20
and 1)
0x00
;00000000
21
0x12
;00010010
SubSys Byte 3
** Insert your SSVID MSB
22
0x34
;00110100
SubSys Byte 2
** Insert your SSVID LSB
23
0x56
;01010110
SubSys Byte 1
** Insert your SSID MSB
24
0x78
;01111000
SubSys Byte 0
** Insert your SSID LSB
25
0x60
;01100000
SysCtrl Byte 0
26
0xB0
;10110000
SysCtrl Byte 1
27
0x44
;01000100
SysCtrl Byte 2
28
0x08
;00001000
SysCtrl Byte 3
29
0x00
;00000000
General Control
2A
0x00
;00000000
GP Event Enable
2B
0x00
;00000000
GP Output
2C
0x22
;00100010
MF Route Byte 0
2D
0x22
;00100010
MF Route Byte 1
2E
0x22
;00100010
MF Route Byte 2
2F
0x04
;00000100
MF Route Byte 3
30
0x02
;00000010
Card Control
31
0x66
;01100110
Device Control
32
0x61
;01100001
Diagnostic
33
0x00
;00000000
PMC Byte 1
34
0x82
;10000010
ExCA ID and Rev
Flag Byte (if 0xFF do not load Function 0
PCI445X Device
1-13
System Implementation
1.3.1
P2C Interface for TPS22X6 Power Switch
The interface between the PCI445X device and TPS22X6 power switch is
serialized to reduce the number of signal lines. The P2C interface requires only
three lines to control the switch. As a PCI445X default, the CLOCK signal is
selected from an external source. It is usually provided from RTC, 32.768 kHz.
The PCI445X device can also generate this clock from an internal ring
oscillator. The typical frequency of the internal ring oscillator is 16 kHz. If using
the internal clock source, then a pulldown resistor is required on the CLOCK
terminal. If arranging for D3 wake implementation, then connect the power
switch RESET terminal to GRST.
Figure 1–4. TPS22X6 Power Switch Interface
VPPA
VCCA
VCCB
PCI445X
DATA
SLOT
A
VCCA
CLOCK
TPS22X6
LATCH
VPPB
SLOT
B
VCCB
Pulldown on
CLOCK
1.3.2
Zoomed Video (ZV) Interface
The PCI445X device has an internally buffered and selectable ZV interface.
It supports three ZV sources, two from PC Cards and one from an external
source. An auto ZV detect function provides software independent ZV
switching. The auto ZV detect function senses the pixel clocks, arbitrates three
inputs, and selects one of them according to priority bits.
Figure 1–5. Example of a ZV Interface
3rd ZV
Source
Buffer
ZVPCLK ZVSTAT
SLOT
A
23
19
Graphic
Controller
PCI445X
SLOT
B
1-14
23
4
Audio
Codec
Stereo
Sound
Controller
System Implementation
If the third ZV source is not implemented, ZVPCLK and ZVSTAT are not
required. To support ZV audio, an audio codec device is required for L and R
sound decoding.
1.3.3
Interrupt Signaling Interface
Serialized Interrupt Interface
The serialized interrupt (ISA and PCI) interface is a single-line interface,
IRQSER. A pullup resistor is required on this terminal. The signal is
synchronous to PCLK, so PCLK is a required signal. Please remember
that SUSPEND gates PCLK internally. Usually this signal is connected to
the south bridge (ex., PIIX4). The IRQSER signal is sharable with other
devices.
Parallel PCI Interrupt
See Section 1.2.2, PCI Bus Interface.
1.3.4
1.3.4.1
Miscellaneous Signals
SUSPEND
The SUSPEND signal gates the PRST and G_RST signals from the PCI445X
device. SUSPEND also gates PCLK inside the PCI445X device in order to
minimize power consumption. Gating PCLK makes the IRQSER state
machine stop until SUSPEND is deasserted. Two requirements for
implementing suspend mode are that the PCI bus must not be parked on the
PCI445X device and IRQSER signaling is not proceeding when SUSPEND is
asserted.
1.3.4.2
RI_OUT and PME
RI_OUT can be programmed on the RI_OUT/PME or MFUNC7 terminal. PME
can be programmed only on the RI_OUT/PME terminal. To support both
RI_OUT and PME in a system, the RI_OUT/PME terminal must be
programmed as PME. These signals are usually connected to the south bridge
(ex., PIIX4) or an embedded controller (EC). Buffers of the RI_OUT/PME type
are open-drain; therefore, a pullup resistor is required on this terminal.
1.3.4.3
SPKROUT
SPKROUT is a dedicated terminal and it is usually mixed to PC sound, and
connected to a sound device.
1.3.4.4
Activity LEDs
Activity LEDs can be programmed on MFUNC terminals. These signals are
active-high and driven for 64 ms duration.
1.3.4.5
Distributed DMA (DDMA)
The PCI445X device supports both PC/PCI (centralized) DMA and a
distributed DMA slave engine for 16-bit PC Card DMA support.
PCI445X Device
1-15
System Implementation
Figure 1–6. Distributed DMA Signal Connection
PCREQ
PCI445X
South
Bridge
PCGNT
(ex., PIIX4)
1.3.5
Requirement of Pullup/Pulldown Resistors
Note:
The PCI445X device has integrated pullup resistors and does not require
external pullups.
Table 1–2. PC Card Interface Pullup Resistor List†‡
Terminal Name
Terminal Name
Terminal Name
(16-bit Memory PC Card)
(16-bit I/O PC Card)
(CardBus PC Card)
Pull Up to Voltage
CD1
CD1
CCD1
VCC
CD2
CD2
CCD2
VCC
VS1
VS1
CVS1
VCC
VS2
VS2
CVS2
VCC
A19
A19
CBLOCK
VCCA or VCCB
A20
A20
CSTOP
VCCA or VCCB
A21
A21
CDEVSEL
VCCA or VCCB
A22
A22
CTRDY
VCCA or VCCB
RESET
RESET
CRST
VCCA or VCCB
WAIT
WAIT
CSERR
VCCA or VCCB
RFU
INPACK
CREQ
VCCA or VCCB
BVD2
SPKR
CAUDIO
VCCA or VCCB
BVD1
STSCHG
CSTSCHG
VCCA or VCCB
A14
A14
CPERR
VCCA or VCCB
READY
IREQ
CINT
VCCA or VCCB
A15
A15
CIRDY
VCCA or VCCB
WP
IOIS16
CCLKRUN
VCCA or VCCB
† The PCI445X device has integrated pullup resistors and does not require external pullups.
‡ CFRAME needs a pullup resistor, but it should be implemented on each PC Card.
1-16
System Implementation
Table 1–3. PCI Bus Interface Pullup Resistor List
PCI Signal
Pull-Up Voltage
FRAME
VCCP
TRDY
VCCP
IRDY
VCCP
DEVSEL
VCCP
STOP
VCCP
SERR
VCCP
PERR
VCCP
LOCK
VCCP
INTA
INTB
INTC
VCCP
CLKRUN
VCCP
PRST
VCCP
G_RST
VCCP
PME
System dependent
The pullup/pulldown on MFUNC depends on how it is implemented. Some
signals may require pullups, others pulldowns, and for a GPI or GPO only the
system designer would know how that line should be pulled.
Table 1–4. Miscellaneous Terminals Pullup Resistor List
PCI Signal
Required Situation
Pullup/Pulldown
Voltage
MFUNC7–MFUNC4
N/C or used as output
VCCP or GND
MFUNC3–MFUNC0
(GPIO3–GPIO0)
N/C or used as output
VCCP or GND
MFUNC7(LOCK)
N/C or used as output
VCCP
CLOCK
Internal OSC is selected
GND
LATCH
If MFUNC7 is used for IDSEL
GND
IRQSER
VCCP
RI_OUT/PME
System dependent
SUSPEND
System dependent
Note: Removing clamping voltage makes all the clamped signals low.
PCI445X Device
1-17
System Implementation
Table 1–5. Required Pullup/Pulldown Resistors
Signal
Resistor
Recommended
Value (Ω)
Condition
LPS
Pulldown (Default)
1.0 k
Required
Note:
1-18
All pullup/pulldown resistor value recommendations are provided as guidelines only. The best value for an individual
design varies depending upon board characteristics, standard design rules and practices, etc.
System Implementation
1.4 BIOS Considerations
1.4.1
Initialization
This section explains which registers require initialization, but does not
discuss detailed information about the registers themselves. Refer to the
corresponding specifications.
Reference white paper:
http://www.microsoft.com/hwdev/busbios/cardbus1.htm
1.4.1.1
PCI Standard Registers Initialization
Command register (PCI offset 04h: 16-bit)
Set to 0007h (enables bus master control, memory space control, and I/O
space control)
Cache line size register (PCI offset 0Ch: 8-bit)
Set to 08h (It is dependent on host-to-PCI bridge specification). It enables
memory read line and memory read multiple command.
Latency timer (PCI offset 0Dh: 8-bit)
This register should reflect each PC Card requirement, but Windows does
not do so. Therefore, system imlementers should determine the value. A
detailed description of this register is in the PCI Local Bus Interface
Specification. Typical setting for this register is 40h.
CardBus socket registers/ExCA base address (PCI offset 10h: 32-bit)
It should be set to 0000 0000h (default).
CardBus latency timer register (PCI offset 1Bh: 8-bit)
Setup of this register is not required because the CardBus bus is a
single-device bus, and the PCI445X device does not deassert CGNT until
a transaction is finished. (It does not mean that the PCI445X device
continues the transaction. The PCI445X device would terminate and
disconnect or abort the transaction as required).
Memory and I/O windows (PCI offset 1Ch – 3Fh)
All memory and I/O windows should be closed (set to base > limit).
Interrupt line register (PCI offset 3Ch: 8-bit)
This register is set to FFh (default).
Subsystem vendor ID and subsystem ID registers (PCI offsets 40h
and 42h: 16-bit/16-bit)
These registers can be set through EEPROM or BIOS. These registers
are read-only as default. Before writing to the registers, the SUBSYSRW
bit (system control register, PCI offset 80h, bit 5) should be set to 1. After
setting up the registers, the SUBSYSRW bit should be set 0 to protect
PCI445X Device
1-19
System Implementation
against unexpected overwriting. The values are system and vendor
dependent.
PC Card 16-bit I/F legacy mode base address register (PCI offset 44h:
32-bit)
Set to 0000 03E1h (16-bit mode) and set to 0000 0001 (CardBus mode) in
response to a disable call.
Power management capabilities register (PCI offset A2h: 16-bit)
If the system does not support VAUX in D3cold state, then clear bit 15.
Power management control/status register (PCI offset A4h: 16-bit)
Clear bit 15 by writing a 1. This should be done after all the other
initialization for the PCI445X device is finished. Make sure that the
PCI445X device is in the D0 state, especially after reboot.
1.4.1.2
PCI TI Proprietary Registers Initialization
The registers listed below should be set up according to system requirements.
Refer to Section 1.1.12.
System control register (PCI offset 80h: 32-bit)
Multimedia control register (PCI offset 84h: 8-bit)
GPIO3–GPIO0 control registers (PCI offset 88h – 8Bh: 8-bit)
Multifunction routing register (PCI offset 8Ch: 32-bit)
Card control register (PCI offset 91h: 8-bit)
Device control register (PCI offset 92h: 8-bit)
Diagnostic register (PCI offset 93h: 8-bit)
DMA socket register 0 and 1 (PCI offset 94h, 98h: 32-bit)
GPE control/status register (PCI offset A8h: 16-bit)
ExCA identification and revision (ExCA offset 800h: 8-bit)
Socket power management register (CardBus socket registers offset 20h:
32-bit)
1.4.2
System Sleeping State Consideration
Supporting sleeping states, such as SUSPEND, STANDBY, and
HIBERNATION are important for a notebook PC environment. The following
describes the sleeping state in APM systems:
1) SUSPEND
Reset signals G_RST and PRST are gated while SUSPEND is asserted.
Power consumption of the PCI445X device is low if SUSPEND is asserted.
1-20
System Implementation
2) Register save/restore
Register content is not preserved in the sleeping state (it depends on the
system implementation). Therefore, BIOS should restore the register
content. Under Windows98, most of the register content is saved and
restored by the pci.vxd and cbss.vxd.
3) Troubleshooting tips for sleep/resume issues
Symptoms of sleep/resume issues are:
System hung up during resume
PC Card does not work after resume
PC Card is not recognized after resume
The probable reason for these problems is that the register content is not
preserved correctly. Checking the register content before taking the system to
the sleep mode and after resuming from the sleep mode may shed some light.
If some of the register settings are not the same after resuming from the sleep
mode, then the BIOS most likely did not restore those values.
1.4.3
Docking System Consideration
Subsystem IDs can be assigned as long as the SUBSYSRW bit (system
control register, PCI offset 80h, bit 5) is set. It is better to do this from EEPROM
as no driver will be running to set the SSID up after a hot-dock/warm-dock.
Therefore, the IDs should be loaded through the I2C interface using an
EEPROM.
PCI445X Device
1-21
Important Information
1.5 Important Information
This section clarifies important system implementation.
1.5.1
G_RST Clamping Rail
G_RST is clamped to VCCP, so removing VCCP causes assertion of G_RST.
Figure 1–7. G_RST and VCCP Relationship
VCCP
VCCP
removed
VCCP = 0
G_RST
G_RST
All other signals with clamping rails behave the same way.
1.5.2
PME/RI_OUT Bit Definition
If PME is selected, only PME is signaled on the PME/RI_OUT terminal. If
RI_OUT is selected, only RI_OUT is signaled. The PCI445X device can signal
PME and RI_OUT as completely separated signals. In this case RI_OUT
should be assigned on the MFUNC terminal.
1.5.3
Serialized IRQ Data Stream
PCI clock is needed for operation of the PCI445X serialized IRQ
state-machine. During SUSPEND assertion, the PCI445X device stops the
IRQSER stream. Before asserting SUSPEND, IRQSER must be stopped.
1.5.4
Socket Power Control
An internal or external CLOCK source is needed for the socket power control
through the P2C interface. The internal ring oscillator is on while the core VCC
is applied to the PCI445X device. External CLOCK source is dependent on the
system.
1.5.5
External CLOCK Frequency for P2C Interface
If an external P2C CLOCK is used, then it will affect:
Advanced CD line noise filtering
VS test speed
TPS22X6 power control interface speed
Use of the internal ring oscillator is recommended. Recommended external
CLOCK source is the 32.768-kHz real-time clock (RTC).
1-22
Global Reset Only Bits/PME Context Bits
Appendix A
Global Reset Only Bits, PME Context Bits
Topic
A.1
Page
Global Reset Only Bits/PME Context Bits
Global Reset Only Bits, PME Context Bits
A-2
A-1
Global Reset Only Bits/PME Context Bits
A.1 Global Reset Only Bits/PME Context Bits
Table A–1.Global Reset Only Cleared Bits
Register Name
Space
Offset
Bit
Subsystem IDs
PCI
40h
31–0
PC card 16-bit legacy mode base address
PCI
44h
31–1
System control
PCI
80h
31–29, 27–24, 22–14, 6–3,
1–0
Multimedia control
PCI
84h
7–0
General status
PCI
85h
2–0
GPIO0 control
PCI
88h
7, 6, 4, 3, 1, 0
GPIO1 control
PCI
89h
7, 6, 3, 1, 0
GPIO2 control
PCI
8Ah
7, 6, 4, 3, 1, 0
GPIO3 control
PCI
8Bh
7, 6, 3, 1, 0
MFUNC routing
PCI
8Ch
31–0
Retry status
PCI
90h
7–1
Card control
PCI
91h
7, 6, 2, 1, 0
Device control
PCI
92h
7–0
Diagnostic
PCI
93h
7–0
Socket DMA register 0
PCI
94h
1–0
Socket DMA register 1
PCI
98h
15–0
GPE control/status
PCI
A8h
10, 9, 8, 2, 1, 0
Note: The following link registers are reset by global reset only.
PCI subsystem identification register—PCI offset 2Ch
MIN_GNT and MAX_LAT register—PCI offset 3Eh
PCI OHCI control register—PCI offset 40h
Power management control and status register—PCI offset 48h
PCI miscellaneous and configuration register—PCI offset F0h
Link enhancement control register—PCI offset F4h
However, there is no support in the OS for the PME-type wake events of the
1394 peripherals at this time.
A-2
Global Reset Only Bits/PME Context Bits
Table A–2.PME Context Bits
Register Name
Space
Offset
Bit
Bridge control
PCI
3Eh
6
Power management capabilities
PCI
A2h
15
Power management control/status
PCI
A4h
15, 8
ExCA power control
ExCA
802h, 842h 4, 3, 1, 0
ExCA interrupt and general control
ExCA
803h/843h
6
ExCA card status change
ExCA
804h/844h
3, 2, 1, 0
ExCA card status change interrupt
ExCA
805h/845h
3, 2, 1, 0
CardBus socket event
CardBus 00h
3, 2, 1, 0
CardBus socket mask
CardBus 04h
3, 2, 1, 0
CardBus socket status
CardBus 10h
6, 5, 4, 2, 1, 0
Global reset only bits are cleared (to default value) only when G_RST is
asserted.
PME context bits are not cleared (to default value) by PRST if the PME_EN
bit is set to 1.
Both G_RST and PRST can be gated by asserting the SUSPEND signal.
Global Reset Only Bits, PME Context Bits
A-3
A-4
Appendix B
PME and RI Behavior
This appendix clarifies PME and RI signal behavior. These signals are
important to support the wake-up event from a PC Card (CardBus and 16-bit
cards.)
Topic
B.1
Page
PME and RI Behavior
B-2
PME and RI Behavior
B-1
B.1 PME and RI Behavior
Table B–1.CardBus CTSCHG and Wake-Up Signals Truth Table
RINGEN
RIMUX
RIENB
PME_EN
PME_STAT
RI_OUT/PME
MFUNC7
0
0
0
0
Latched
–––
–––
0
0
0
1
Latched
Latched CSTSCHG
–––
0
0
1
0
Latched
–––
–––
0
0
1
1
Latched
–––
–––
0
1
0
0
Latched
–––
–––
0
1
0
1
Latched
Latched CSTSCHG
–––
0
1
1
0
Latched
–––
–––
0
1
1
1
Latched
Latched CSTSCHG
–––
1
0
0
0
Latched
–––
–––
1
0
0
1
Latched
Latched CSTSCHG
–––
1
0
1
0
Latched
CSTSCHG
CSTSCHG
1
0
1
1
Latched
CSTSCHG
CSTSCHG
1
1
0
0
Latched
–––
–––
1
1
0
1
Latched
Latched CSTSCHG
–––
1
1
1
0
Latched
–––
CSTSCHG
1
1
1
1
Latched
Latched CSTSCHG
CSTSCHG
Table B–2.16-Bit Card RI/STSCHG and Wake-Up Signals Truth Table
B-2
RINGEN RIMUX
RIENB
PME_EN
PME_STAT
RI_OUT/PME
MFUNC7
0
–––
–––
–––
–––
–––
–––
1
0
0
0
Latched
–––
–––
1
0
0
1
Latched
Latched RI
–––
1
0
1
0
Latched
RI
RI
1
0
1
1
Latched
RI
RI
1
1
0
0
Latched
–––
–––
1
1
0
1
Latched
Latched RI
–––
1
1
1
0
Latched
–––
RI
1
1
1
1
Latched
Latched RI
RI
PCI445X Buffer Types
Appendix C
PCI445X Buffer Types
Topic
C.1
Page
PCI445X Buffer Types
C-2
PCI445X Buffer Types
C-1
PCI445X Buffer Types
C.1 PCI445X Buffer Types
Table C–1. PCI445X Terminal Function Assignment and Buffer Types
Signal Name
Terminal
Type
Signal Name
Terminal
Type
A_CAD0
B8
TS
A_CAD28
N2
TS
A_CAD1
A7
TS
A_CAD29
N3
TS
A_CAD2
C8
TS
A_CAD30
P1
TS
A_CAD3
A6
TS
A_CAD31
D9
TS
A_CAD4
B7
TS
A_CAUDIO
M1
I
A_CAD5
B6
TS
A_CBLOCK
D2
P
A_CAD6
C7
TS
A_CC/BE0
A4
TS
A_CAD7
D7
TS
A_CC/BE1
C3
TS
A_CAD8
C6
TSO
A_CC/BE2
F2
TS
A_CAD9
C5
TS
A_CC/BE3
J1
TS
A_CAD10
B4
TS
A_CCD1
A8
I
A_CAD11
A3
TS
A_CCD2
M4
TS
A_CAD12
C4
TS
A_CCLK
E3
TS
A_CAD13
D5
TS
A_CLKRUN
M3
STS
A_CAD14
B2
TS
A_CDEVSEL
D1
STS
A_CAD15
B3
TS
A_CFRAME
G4
STS
A_CAD16
A2
TS
A_CGNT
C1
STS
A_CAD17
F1
TS
A_CINT
L2
I
A_CAD18
G3
TS
A_CIRDY
E1
STS
A_CAD19
G2
P
A_CPAR
C2
TS
A_CAD20
H3
TS
A_CPERR
D3
STS
A_CAD21
H1
TS
A_CREQ
J3
I
A_CAD22
J4
TS
A_CRST
H2
O
A_CAD23
J2
TS
A_CSERR
L3
I
A_CAD24
K2
TS
A_CSTOP
E4
STS
A_CAD25
K3
TS
A_CSTSCHG
M2
I
A_CAD26
K1
TS
A_CTRDY
E2
STS
A_CAD27
N1
TS
A_CVS1
L1
I/O
Note:
The voltage sense terminals (VS1/CVS1, VS2/CVS2) are always driven low except under the following conditions:
1) High-impedance state during RESET
2) Toggle during socket interrogation
C-2
PCI445X Buffer Types
Table C–1. PCI445X Terminal Function Assignment and Buffer Types (Continued)
Signal Name
Terminal
Type
Signal Name
Terminal
Type
A_CVS2
G1
I/O
AD25
N20
TS
A_RSVD
A5
TS
AD26
M17
TS
A_RSVD
B1
TS
AD27
M18
TS
A_RSVD
P2
TS
AD28
M19
TS
AD0
V13
TS
AD29
M20
TS
AD1
Y14
TS
AD30
L19
TS
AD2
W14
TS
AD31
L18
TS
AD3
Y15
TS
B_CAD0
J19
TS
AD4
W15
TS
B_CAD1
J17
TS
AD5
Y16
TS
B_CAD2
J18
TS
AD6
U14
TS
B_CAD3
H19
TS
AD7
V15
TS
B_CAD4
H20
TS
AD8
Y17
TS
B_CAD5
G20
TS
AD9
V16
TS
B_CAD6
H18
TS
AD10
W17
TS
B_CAD7
F20
TS
AD11
Y18
TS
B_CAD8
G18
TS
AD12
U16
TS
B_CAD9
E20
TS
AD13
V17
TS
B_CAD10
G17
TS
AD14
W18
TS
B_CAD11
F18
TS
AD15
Y19
TS
B_CAD12
E18
TS
AD16
T18
TS
B_CAD13
D20
TS
AD17
T19
TS
B_CAD14
C20
TS
AD18
T20
TS
B_CAD15
D19
TS
AD19
R18
TS
B_CAD16
E17
TS
AD20
P17
TS
B_CAD17
C16
TS
AD21
R19
TS
B_CAD18
B16
TS
AD22
R20
TS
B_CAD19
A16
TS
AD23
P18
TS
B_CAD20
D14
TS
AD24
N19
TS
B_CAD21
A15
TS
Note:
The voltage sense terminals (VS1/CVS1, VS2/CVS2) are always driven low except under the following conditions:
1) High-impedance state during RESET
2) Toggle during socket interrogation
PCI445X Buffer Types
C-3
PCI445X Buffer Types
Table C–1. PCI445X Terminal Function Assignment and Buffer Types (Continued)
Signal Name
Terminal
Type
Signal Name
Terminal
Type
B_CAD22
C14
TS
B_CSERR
B11
STS
B_CAD23
A14
TS
B_CSTOP
A20
STS
B_CAD24
A13
TS
B_CSTSCHG
A11
I
B_CAD25
D12
TS
B_CTRDY
C17
STS
B_CAD26
C12
TS
B_CVS1
B12
I/O
B_CAD27
C10
TS
B_CVS2
C15
I/O
B_CAD28
D10
TS
B_RSVD
C9
TS
B_CAD29
A9
TS
B_RSVD
C19
TS
B_CAD30
B9
TS
B_RSVD
G19
TS
B_CAD31
D9
TS
C/BE0
W16
TS
B_CAUDIO
C11
I
C/BE1
V18
TS
B_CBLOCK
C18
STS
C/BE2
U20
TS
B_CC/BE0
F19
TS
C/BE3
N18
TS
B_CC/BE1
D18
TS
CLKRUN
K18
O
B_CC/BE2
A17
TS
CLOCK
U12
O
B_CC/BE3
C13
I
DATA
V12
O
B_CCD1
J20
I
DEVSEL
U19
STS
B_CCD2
B10
I
FRAME
V20
STS
B_CCLK
B17
TS
G_RST
Y12
I
B_CDEVSEL
B18
STS
GND
A1
P
B_CFRAME
A18
STS
GND
D4
P
B_CGNT
A19
O
GND
D8
P
B_CINT
A12
I
GND
D13
P
B_CIRDY
D16
STS
GND
D17
P
B_CLKRUN
A10
STS
GND
H4
P
B_CPAR
B20
TS
GND
H17
P
B_CPERR
B19
STS
GND
N4
P
B_CREQ
B14
I
GND
N17
P
B_CRST
B15
O
GND
U4
P
Note:
The voltage sense terminals (VS1/CVS1, VS2/CVS2) are always driven low except under the following conditions:
1) High-impedance state during RESET
2) Toggle during socket interrogation
C-4
PCI445X Buffer Types
Table C–1. PCI445X Terminal Function Assignment and Buffer Types (Continued)
Signal Name
Terminal
Type
Signal Name
Terminal
Type
GND
U8
P
PHY_DATA6
U9
TS
GND
U13
P
PHY_DATA7
V9
TS
GND
U17
P
PHY_LREQ
Y5
O
GNT
K20
I
PME/RI_OUT
Y13
OD
IDSEL/MFUNC7
P20
I/O
PRST
K19
I
IRDY
T17
STS
REQ
L20
O
IRQSER
W13
TS
SCL
W10
TS
LATCH
W12
TS
SDA
Y9
TS
LINKON
Y6
I
SERR
Y20
OD
LPS
W5
O
SPKROUT
V11
O
MFUNC0
W11
I/O
STOP
V19
STS
MFUNC1
Y11
I/O
SUSPEND
U11
I
MFUNC2
Y10
I/O
TRDY
U18
STS
MFUNC3
V10
I/O
VCCA
B5
P
MFUNC4
W9
I/O
VCCA
F3
P
MFUNC5
V5
I/O
VCCA
L4
P
MFUNC6
Y4
I/O
VCCB
B13
P
PAR
W19
STS
VCCB
E19
P
PCLK
K17
I
VCCP
P19
P
PERR
W20
STS
VCCP
V14
P
PHY_CLK
V6
I
VCC3.3
D6
P
PHY_CTL0
U7
TS
VCC3.3
D11
P
PHY_CTL1
W6
TS
VCC3.3
D15
P
PHY_DATA0
V7
TS
VCC3.3
F4
P
PHY_DATA1
W7
TS
VCC3.3
F17
P
PHY_DATA2
Y7
TS
VCC3.3
K4
P
PHY_DATA3
V8
TS
VCC3.3
L17
P
PHY_DATA4
W8
TS
VCC3.3
R4
P
PHY_DATA5
Y8
TS
VCC3.3
R17
P
PCI445X Buffer Types
C-5
PCI445X Buffer Types
Table C–1. PCI445X Terminal Function Assignment and Buffer Types (Continued)
Signal Name
Terminal
Type
Signal Name
Terminal
Type
VCC3.3
U6
P
ZV_UV4
W1
TSO
VCC3.3
U10
P
ZV_UV5
Y1
TSO
VCC3.3
U15
P
ZV_UV6
W2
TSO
ZV_HREF
P3
TSO
ZV_UV7
Y2
TSO
ZV_LRCLK
V4
TSO
ZV_VSYNC
R2
TS
ZV_MCLK
W4
TSO
ZV_Y0
T1
TSO
ZV_PCLK
Y3
TSO
ZV_Y1
P4
TSO
ZV_SCLK
W3
TSO
ZV_Y2
R3
TSO
ZV_SDATA
U5
TSO
ZV_Y3
T2
TSO
ZV_UV0
T4
TSO
ZV_Y4
U1
TSO
ZV_UV1
V2
TSO
ZV_Y5
T3
TSO
ZV_UV2
U3
TSO
ZV_Y6
U2
TSO
ZV_UV3
V3
TSO
ZV_Y7
V1
TSO
C-6
PCI445X Buffer Types
Table C–2. Buffer Type Abbreviations
Buffer Type
Description
I/O
Standard input/output
I
Standard input only
O
Standard output only
OD
Open drain
P
Power, GND, or clamp rail
STS
Sustained 3-state bidirectional. An active-low signal must be driven high for one cycle
before deasserting.
TS
3-state bidirectional
TSO
3-state output only
PCI445X Buffer Types
C-7
C-8
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2000:08:23 15:46:40 Producer : Acrobat Distiller Command 3.02b for Solaris 2.3 and later (SPARC) Title : PCI445x PC Card and 1394 OHCI Link Controller Implementation Guide Subject : User's Guide Author : Texas Instruments, Incorporated Keywords : scpu007 Litnumver : scpu007.1 Modify Date : 2000:08:23 15:48:42-05:00 Page Count : 46EXIF Metadata provided by EXIF.tools