The Coleman 830-500 Tent Lighting System (315MHz Tx) User Manual 830 500 Series

The Coleman Company Inc. Tent Lighting System (315MHz Tx) 830 500 Series

User Manual

Carefully read all instructions before use and save for future reference.TO INSTALL OR REPLACE POWER PACK BATTERIESYour new Coleman®Tent Lighting System operates on 8 “D” cell batteries.For longest life use alkaline batteries.1. If Red Button on front of battery pack is glowing, push button to turn power “OFF”. (Fig. 1)2. Turn battery pack over and place coin into slot and rotate to unlock. (Fig. 2)3. Lift up lid and install 8 batteries in the correct orientation as shown on the battery compartment. Always be careful that batteries are installed correctly. (Fig. 3)4. Close lid, insert coin into slot and rotate to locked position.5. Place battery pack in pocket sewn into side of tent. (Fig. 4)NOTE: Never operate tent light if battery pack is not stored in upright position, with red button facing outward, in pocket.TO REPLACE REMOTE CONTROL BATTERYNOTE: Remote control feature is not available on all versions of this Coleman®Tent Lighting System.1. Remove 4 screws from back of transmitter and install one12v, 23AE alkaline battery. (Fig. 7)2. Reassemble transmitter.This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance couldvoid the user’s authority to operate this equipment.This device complies with Part 18 of the FCC Rules.Note: This product may cause interference to radio equipment and should not be installed near maritime safety NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between equipment and receiver.The Responsible Party information as below:• Applicant name in full: The Coleman Company, Inc.• Address: 3600 N. Hydraulic, Wichita, KS 67219• Contact in USA: Rex Weigand / Director of Product Safety & Compliance• Phone: (316) 832-3056• Fax: (316) 832-6193• Email address: RWeigand@coleman.com• Connect the equipment into an outlet on a circuit different from that which the receiver is needed.• Consult the dealer or an experienced radio/TV technician for help.NAMELOC ®NAMELOC ETNET ED EGARIALCÉ / METSYS GNITHGIL TNET®Model 830-500 SeriesModèle de la série 830-50011/2006For products purchased in Canada:Sunbeam Corporation (Canada) LimitedDBA Jarden Consumer Solutions5975 Falbourne StreetMississauga, Ontario, Canada L5R 3V85-Year Limited WarrantyThe Coleman Company, Inc. (“Coleman”) warrants that for a period of five years from the date of original retail purchase,this product will be free from defects in material and workmanship. Coleman, at its option, will repair or replace this product orany component of the product found to be defective during the warranty period. Replacement will be made with a new orremanufactured product or component. If the product is no longer available, replacement may be made with a similar productof equal or greater value. No warranty is provided for batteries and light bulbs. This is your exclusive warranty.This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep theoriginal sales receipt. Proof of purchase is required to obtain warranty performance. Coleman dealers, service centers or retailstores selling Coleman®products do not have the right to alter, modify or in any way change the terms and conditions of thiswarranty.What This Warranty Does Not CoverThis warranty does not cover normal wear of parts, parts that are not genuine Coleman®parts, or damage resulting from anyof the following: negligent use or misuse of the product; use on improper voltage or current; commercial use of the product;use contrary to the operating instructions or disassembly, repair or alteration by anyone other than Coleman or an authorizedservice center. Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes. Warranty void ifdamage to product results from the use of a part other than a genuine Coleman®part.COLEMAN SHALL NOT BE LIABLE FOR DEFECTS THAT ARE CAUSED BY THE USE OF UNAUTHORIZED PARTS ORSERVICE. COLEMAN SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THEBREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITIONS. EXCEPT TO THE EXTENT PROHIBITED BYAPPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ISLIMITED IN DURATION TO THE DURATION OF THE ABOVE WARRANTY OR CONDITIONS. SOME STATES, PROVINCES,OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGESOR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSION MAYNOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHERRIGHTS THAT VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.How to Obtain Warranty ServiceTake the product to an authorized Coleman service center.You can find the nearest authorized Coleman service center by visiting www.coleman.com or calling 1-800-835-3278 orTDD 316-832-8707 in the United States or 1 800 387-6161 in Canada. If a service center is not conveniently located, attach tothe product a tag that includes your name, address, daytime telephone number and description of the problem. Include a copyof the original sales receipt. Carefully package the product and send either by courier or insured mail with shipping andinsurance prepaid to:For products purchased in the United States:The Coleman Company, Inc.3600 North HydraulicWichita, KS 67219The costs of transporting the product to Coleman or an authorized service center for warranty service is the responsibility ofthe purchaser.DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.If you have any questions regarding this warranty please call 1-800-835-3278 orTDD 316-832-8707 in the United States or 1 800 387-6161 in Canada.©2006 The Coleman Company, Inc. All rights reserved.Coleman®, , and are registered trademarks of The Coleman Company, Inc.NAMELOC®NAMELOC ETNET ED EGARIALCÉ / METSYS GNITHGIL TNET®Fig. 4TENT LIGHTINGSYSTEMHow to Use and Enjoy Your Coleman®Fig. 2Fig. 1Fig. 3TO CHANGE FLUORESCENT TUBENOTE: This tent light uses one 15-watt fluorescent spiral tube (See Parts List for replacement part #). Fluorescent spiral tubes are very fragile. Handle with care.1. Make sure power pack light is turned “OFF” and red button is not glowing.2. Grasp globe on tent light and turn clockwise to remove. (Fig. 5) 3. Gently press down on fluorescent spiraltube and turn counterclockwise until both alignment tabs are visible in locating slots of housings. Remove tube. (Fig. 6)4. Install new fluorescent spiral tube by placing alignment tabs in locating slots of reflector. Gently push down and rotate clockwise until secure.5. Reattach globe to light housing by turning counterclockwise until tightened. Do not overtighten.POCKETTENT FLOORSIDE OF TENTFig. 6Fig. 5Fig. 7TO OPERATE TENT LIGHT1. Screw tent light into socket at top of tentby turning clockwise. (Fig. 8)2. Unsnap rubber plug from side of power packand plug the power cord that was installed in your tent into the power pack. (Fig. 9)3. Push the red button on the power pack to turn on main power. The button on the power pack and the tent light will glow when main power is “ON”. (Fig. 9)4. Push red button on tent light: a) once for “HIGH” light setting, twice for “LOW” light setting, a third time will turn light “OFF”.(Fig. 10)TO OPERATE TENT LIGHT WITH REMOTE CONTROL1. Push the red button on the power pack to turn on main power. The button on the power pack and the tent light will glow when main power is “ON”. (Fig. 10)2. Push the button on the remote control transmitter: a) once for “HIGH” light setting, twice for “LOW” light setting, a third time will turn light “OFF”. (Fig. 11)Fig. 9RED BUTTONFig. 10LIGHTRED BUTTONFig. 11TRANSMITTERBUTTONSYSTÈME D’ÉCLAIRAGE DE TENTEProfitez au maximum de ce système Coleman®ALIGNMENTTABSCLOSE OPEN830-500_Series.qxd 11/17/06 2:23 PM Page 1Fig. 8
Carefully read all instructions before use and save for future reference.TO INSTALL OR REPLACE POWER PACK BATTERIESYour new Coleman®Tent Lighting System operates on 8 “D” cell batteries.For longest life use alkaline batteries.1. If Red Button on front of battery pack is glowing, push button to turn power “OFF”. (Fig. 1)2. Turn battery pack over and place coin into slot and rotate to unlock. (Fig. 2)3. Lift up lid and install 8 batteries in the correct orientation as shown on the battery compartment. Always be careful that batteries are installed correctly. (Fig. 3)4. Close lid, insert coin into slot and rotate to locked position.5. Place battery pack in pocket sewn into side of tent. (Fig. 4)NOTE: Never operate tent light if battery pack is not stored in upright position, with red button facing outward, in pocket.TO REPLACE REMOTE CONTROL BATTERYNOTE: Remote control feature is not available on all versions of this Coleman®Tent Lighting System.1. Remove 4 screws from back of transmitter and install one12v, 23AE alkaline battery. (Fig. 7)2. Reassemble transmitter.This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance couldvoid the user’s authority to operate this equipment.This device complies with Part 18 of the FCC Rules.Note: This product may cause interference to radio equipment and should not be installed near maritime safety NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between equipment and receiver.The Responsible Party information as below:• Applicant name in full: The Coleman Company, Inc.• Address: 3600 N. Hydraulic, Wichita, KS 67219• Contact in USA: Rex Weigand / Director of Product Safety & Compliance• Phone: (316) 832-3056• Fax: (316) 832-6193• Email address: RWeigand@coleman.com• Connect the equipment into an outlet on a circuit different from that which the receiver is needed.• Consult the dealer or an experienced radio/TV technician for help.NAMELOC ®NAMELOC ETNET ED EGARIALCÉ / METSYS GNITHGIL TNET®Model 830-500 SeriesModèle de la série 830-50011/2006For products purchased in Canada:Sunbeam Corporation (Canada) LimitedDBA Jarden Consumer Solutions5975 Falbourne StreetMississauga, Ontario, Canada L5R 3V85-Year Limited WarrantyThe Coleman Company, Inc. (“Coleman”) warrants that for a period of five years from the date of original retail purchase,this product will be free from defects in material and workmanship. Coleman, at its option, will repair or replace this product orany component of the product found to be defective during the warranty period. Replacement will be made with a new orremanufactured product or component. If the product is no longer available, replacement may be made with a similar productof equal or greater value. No warranty is provided for batteries and light bulbs. This is your exclusive warranty.This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep theoriginal sales receipt. Proof of purchase is required to obtain warranty performance. Coleman dealers, service centers or retailstores selling Coleman®products do not have the right to alter, modify or in any way change the terms and conditions of thiswarranty.What This Warranty Does Not CoverThis warranty does not cover normal wear of parts, parts that are not genuine Coleman®parts, or damage resulting from anyof the following: negligent use or misuse of the product; use on improper voltage or current; commercial use of the product;use contrary to the operating instructions or disassembly, repair or alteration by anyone other than Coleman or an authorizedservice center. Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes. Warranty void ifdamage to product results from the use of a part other than a genuine Coleman®part.COLEMAN SHALL NOT BE LIABLE FOR DEFECTS THAT ARE CAUSED BY THE USE OF UNAUTHORIZED PARTS ORSERVICE. COLEMAN SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THEBREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITIONS. EXCEPT TO THE EXTENT PROHIBITED BYAPPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ISLIMITED IN DURATION TO THE DURATION OF THE ABOVE WARRANTY OR CONDITIONS. SOME STATES, PROVINCES,OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGESOR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSION MAYNOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHERRIGHTS THAT VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.How to Obtain Warranty ServiceTake the product to an authorized Coleman service center.You can find the nearest authorized Coleman service center by visiting www.coleman.com or calling 1-800-835-3278 orTDD 316-832-8707 in the United States or 1 800 387-6161 in Canada. If a service center is not conveniently located, attach tothe product a tag that includes your name, address, daytime telephone number and description of the problem. Include a copyof the original sales receipt. Carefully package the product and send either by courier or insured mail with shipping andinsurance prepaid to:For products purchased in the United States:The Coleman Company, Inc.3600 North HydraulicWichita, KS 67219The costs of transporting the product to Coleman or an authorized service center for warranty service is the responsibility ofthe purchaser.DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.If you have any questions regarding this warranty please call 1-800-835-3278 orTDD 316-832-8707 in the United States or 1 800 387-6161 in Canada.©2006 The Coleman Company, Inc. All rights reserved.Coleman®, , and are registered trademarks of The Coleman Company, Inc.NAMELOC®NAMELOC ETNET ED EGARIALCÉ / METSYS GNITHGIL TNET®Fig. 4TENT LIGHTINGSYSTEMHow to Use and Enjoy Your Coleman®Fig. 2Fig. 1Fig. 3TO CHANGE FLUORESCENT TUBENOTE: This tent light uses one 15-watt fluorescent spiral tube (See Parts List for replacement part #). Fluorescent spiral tubes are very fragile. Handle with care.1. Make sure power pack light is turned “OFF” and red button is not glowing.2. Grasp globe on tent light and turn clockwise to remove. (Fig. 5) 3. Gently press down on fluorescent spiraltube and turn counterclockwise until both alignment tabs are visible in locating slots of housings. Remove tube. (Fig. 6)4. Install new fluorescent spiral tube by placing alignment tabs in locating slots of reflector. Gently push down and rotate clockwise until secure.5. Reattach globe to light housing by turning counterclockwise until tightened. Do not overtighten.POCKETTENT FLOORSIDE OF TENTFig. 6Fig. 5Fig. 7TO OPERATE TENT LIGHT1. Screw tent light into socket at top of tentby turning clockwise. (Fig. 8)2. Unsnap rubber plug from side of power packand plug the power cord that was installed in your tent into the power pack. (Fig. 9)3. Push the red button on the power pack to turn on main power. The button on the power pack and the tent light will glow when main power is “ON”. (Fig. 9)4. Push red button on tent light: a) once for “HIGH” light setting, twice for “LOW” light setting, a third time will turn light “OFF”.(Fig. 10)TO OPERATE TENT LIGHT WITH REMOTE CONTROL1. Push the red button on the power pack to turn on main power. The button on the power pack and the tent light will glow when main power is “ON”. (Fig. 10)2. Push the button on the remote control transmitter: a) once for “HIGH” light setting, twice for “LOW” light setting, a third time will turn light “OFF”. (Fig. 11)Fig. 9RED BUTTONFig. 10LIGHTRED BUTTONFig. 11TRANSMITTERBUTTONSYSTÈME D’ÉCLAIRAGE DE TENTEProfitez au maximum de ce système Coleman®ALIGNMENTTABSCLOSE OPEN830-500_Series.qxd 11/17/06 2:23 PM Page 1Fig. 8

Navigation menu