The Genie a Division of Overhead Door ACSCT1 Garage Door Opener Transmitter User Manual 2 Page 1

The Genie Company a Division of Overhead Door Corporation Garage Door Opener Transmitter 2 Page 1

User Manual

3 4Battery and HolderBlueButtons!Moving Door or Gate can cause serious injury or death• Do Not program Remote Control unless the Door Safety Reverse works as described in Operator’s Manual.• Keep people clear of opening while Door is moving.• Do Not allow children to play with the Remote Control, or Door Operator.If Safety Reverse does not work properly:• This Remote Controller WILL NOT WORK.• Disconnect Operator using Manual Release.• Do Not use Remote Control, or Door Operator.• Refer to Operator Owner’s Manual before attempting any repairs.Button assignments can be mixed and matched any wayyou wish. For example, button #1 used for INTELLICODE2®, button #2 used for INTELLICODE®, button #3 (if applicable) used for INTELLICODE2®. Simply follow the steps of the appropriate section foreach individual button.1. On your Remote Controller—Press and hold any twobuttons from 5 — 30 seconds, (the green light will come on when the buttons are pressed and will begin blinking after 2 seconds)(repeating one blink—pause). Your random access code is set depending on how long you hold the buttons. Fig. 1.Release the buttons, (the green light will continue to blink). NOTE: Programming can only be done while the green light is blinking.NOTE: The Green Light (LED) also indicates the strength of thebattery. It will get dimmer as the battery gets weaker. When theLight no longer comes on, you will have several operationcycles remaining, but be aware you will need to replace the battery soon. The expected life of the ENERGIZER CR2032Lithium/Manganese Dioxide Battery is at least 5 years.2. On your Remote Controller—Press any one button, (the green light will go out.3. On your Door Operator—Locate the Learn Code Button. (Refer to your Owner’s Manual.)4. On your Door Operator—Press the Learn Code Button, (the Learn Code Light will begin blinking twice each second). 5. On your Remote Controller—Press the button you wish to use for controlling the first door operator, (the Learn Code Light will stay on, no blinking). Press the same button again, (the Learn Code Light will go out).Press the same button again, (the door should operate).6. Repeat Steps 3 — 5 for any additional INTELLICODE2®equipped door operator you wish to control with this Remote.NOTE: Once programming is complete, it cannot be changedsimply by pressing a button or combination of buttons. Thishelps prevent accidental disabling of your Remote Controller.If you need to reprogram your remote for any reason, see“REPROGRAMMING” Section on back.340000000012GreenLight ScrewINTELLICODE2SectionRemoteControllerw/WARNINGCatchYour new INTELLICODE2®Remote Controlleris equipped to operate both the latest INTELLICODE2®Garage Door Operators andall previous models built with INTELLICODE®. Look on your Garage Door Operator for the INTELLICODE2®label. If you have a INTELLICODE2®unit, follow thesteps in the “INTELLICODE2” Section below. If you have a previous style INTELLICODE®unit,follow the steps in the “INTELLICODE” Sectionon back.
1. On your Remote Controller—Press and hold any twobuttons from 5 — 30 seconds, (the green light will come on when the buttons are pressed and will begin blinking after 2 seconds)(repeating one blink—pause). Your random access code is set depending on how long you hold the buttons.Release the buttons, (the green light will continue to blink).NOTE: Programming can only be done while the green light isblinking.2. On your Remote Controller—Press the same two buttons and hold until after the Green Light begins blinking, (the green light will come on and stay on as the buttons are held down, and after 2 seconds will begin blinking, repeating 2 blinks—pause).3. On your Remote Controller—Press the button you wish to use to control the door operator. (The green light will continue blinking as you hold down the button). Release the button, (the green light will go out).Repeat Step 3 for each button that will be assigned to a previous style INTELLICODE®Operator. 4. On your Door Operator—Locate the Learn Code Button. (Refer to your Owner’s Manual.)5. On your Door Operator—Press the Learn Code Button, (the Learn Code Light will begin blinking twice each second). 6. On your Remote Controller—Press the button you wish to use for controlling the first door operator, (the Learn Code Light will stay on, no blinking). Press the same button again, (the Learn Code Light will go out).Press the same button again, (the door should operate).7. Repeat Steps 4 —6 for any additional INTELLICODE®equipped door operator you wish to control with this Remote.NOTE: Once programming is complete, it cannot be changedsimply by pressing a button or combination of buttons. Thishelps prevent accidental disabling of your Remote Controller.If you need to reprogram your remote for any reason, see“REPROGRAMMING” Section.If, during the first few weeks of operation, you wish to reprogram your Remote for any reason, simply follow the initial programming procedure again. If you attempt reprogramming at some point long after initialprogramming (usually beyond 3 weeks), when you press thetwo buttons in Step 1 you may see an immediate rapid flashing of the Green Light. Your Remote has considered theinitial program as permanent and is protecting against unauthorized attempts to change your code. You Must then:1. Remove the Battery, and with the battery removed,2. Press and hold one of the blue buttons on the circuit board for 1 or 2 seconds. (This insures all power is drained from the circuit.) Fig. 5.3. Replace the battery.4. Begin programming as before.1. Slide the visor Clip off the back of the Remote and remove the small screw.2. With a thin flat object (the visor clip works well) push in on the catch located in the small notch at the base of the Remote. This releases the hinged section of the case. Fig. 2.3. Holding the Top half of the case in one hand, and the hinged section in the other, gently pull the two halves apart. Fig. 3.4. Flip the hinged section out of the way and slide the battery out of its holder. Fig. 4.5. Using a new ENERGIZER CR2032 Long Life Lithium/Manganese Dioxide Battery, reverse the process.WARNINGAlways keep batteries out of the reach of children. They pose an extreme internal health hazard. If swallowed contact a physician immediately. CAUTIONBe sure to comply with Local and Federal Regulations Concerning the disposal of Lithium/Manganese Dioxide Batteries.FCC CertifiedThis device complies with FCC Part 15 of the FCC Rules. Operationis subject to the following conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.Changes or modifications not expressly approved by the manufacturercould void the user’s authority to operate the equipment.Certificado por la FCCEste dispositivo cumple con las normas de la FCC (Comisión Federalde Comunicaciones), Parte 15 de Dominio de FCC. La operación estésujeta a las dos condiciones siguientes: (1) Este dispositivo puede nocausar interferencia dañina, y (2) este dispositivo debe aceptarcualquier interferencia, incluyendo la interferencia que pueda causar laoperación indeseable.Los cambios o modificaciones no aprobados expresamente por el fabricante pueden invalidar la autoridad del usuario de operar el equipoCertifié conforme à la réglementation FCCCe dispositif est conforme aux normes FCC section 15 de Ordonnancede FCC. Son fonctionnement est soumis aux deux conditions suivantes: (1) Il ne doit pas causer une interférence dangereuse et (2) ce dispositif doit accepter toute interférence y compris l’interférence quipeut causer le fonctionnement non désiré.Les changements ou les modifications non approuvés expressémentpar le fabricant peuvent annuler l’autorisation del’utilisateur à actionnerl’équipement.BATTERY REPLACEMENTINTELLICODE SectionREPROGRAMMINGBATTERY STORAGE & HANDLING

Navigation menu