The Genie a Division of Overhead Door ACSDA1 GARAGE DOOR OPENER TRANSMITTER User Manual WK4 Page 1

The Genie Company a Division of Overhead Door Corporation GARAGE DOOR OPENER TRANSMITTER WK4 Page 1

USERS MANUAL

STEP 1: SETTING YOUR WIRELESS KEYPAD PIN(PERSONAL IDENTIFICATION NUMBER)AActivate programming mode.•Press (in order) .–Red LED blinks - once per second.•Enter your PIN (3 to 8 characters).•Press .–Red LED blinks - twice per second and turns off.STEP 1: SETTING YOUR WIRELESS KEYPAD PIN(PERSONAL IDENTIFICATION NUMBER)AActivate programming mode.•Press (in order) .–Red LED blinks - once per second.•Enter your PIN (3 to 8 characters).•Press .–Red LED blinks - twice per second and turns off.3DEF124567890GHI JKL MNOPQRSTUVWXYZ9V¤This Wireless Keypad is compatible with all INTELLICODE® radio equipped GENIE® products.•Drill with 1/16" Drill Bit •Phillips Screwdriver •Pencil•Mounting Screws INCLUDED inside Battery CompartmentInterchangeable Flip-up Cover available in 3 optional Classic Colors to match your home’sexterior decorRed LED indicates Battery Power and Status during Use and ProgrammingBacklit Keypad for Ease of Use at NightBattery Compartment9 Volt Battery(included)Instructions•Ability to Control up to threeGenie® INTELLICODE® Openers•Simple to Program and Install •PIN Codes can be up to 8 Characters •Low Battery Power Indicator•Stays Programmed During Battery Change •Temporary PIN for Special Purpose AccessOPERATING INSTRUCTIONS(KEEP FOR FUTURE REFERENCE)A Moving door can cause serious injury or death.1Keep people clear of opening while door is moving.2DoNotallow children to play with Wireless Keypad.3During programming, the door opener could begin to run, so stay away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the Opener by pulling the Emergency Release.3528135342WARNINGSTEP 3: OPERATING ONE DOOR OPENERATo move the garage door:•Enter your PIN.•Press .Proceed to Section 3 - Mounting Instructions.STEP 2: PROGRAMMING ONE DOOR OPENERAFind the Learn Code Button and Learn Code Indicator LED on your door opener.–If your door opener has a black antenna wire,the Learn Code Button and Indicator LED are located near the antenna.(The light lens may need to be opened.)–If your door opener does nothave an antenna,you have an external receiver.The external receiver cover must be removed to access the Learn Code Button and Indicator LED.•Press the Learn Code Button.–Learn Code Indicator LED (on Opener) will blink.•Enter your PIN and press on keypad.–Learn Code Indicator LED stays on.•Press again.–Learn Code Indicator LED turns off.BASIC PROGRAMMING FORONE DOOR OPENERRed IndicatorLEDLearn Code ButtonLocatedon OpenerHousingSTEP 3: PROGRAMMING DOOR OPENERSADecide which door will be door #1, #2 and #3.•Press the Learn Code Button (see Section 1 Step 2).–Learn Code Indicator LED (on Opener) blinks.•Enter your PIN and press .–Learn Code Indicator LED stays on.•Press the number you have picked for thisdoor Opener ( or or ).–Learn Code Indicator LED stays on.•Press .–Learn Code Indicator LED turns off.BRepeat step A above for each door opener.Each door opener must be programmed to receive the signal from the Wireless Keypad.STEP 4: OPERATING 2 OR 3 DOOR OPENERSATo move one of the doors.•Enter your PIN.•Press .•Press door opener number ( or or ).SEE NOTE AT BOTTOM OF SECTION 1Proceed to Section 3 - Mounting Instructions.PROGRAMMING FOR2 OR 3 DOOR OPENERS MOUNTING INSTRUCTIONSThe Keypad must be mounted in sight of the door(s), at least 5 feet above the ground and clear of any moving door parts.AMount Keypad.(Mounting screws located inside battery compartment.)•Remove Battery Cover. See Section 4 Figure 2.•Drill a 1/16”pilot hole for the top mounting screw.•Install a screw into the drilled hole,leaving a 1/8" gap between the screw headand the wall. See Figure 1.•Hook the Keypad over the screw.•Mark, drill pilot hole and fasten bottom screw.•Reinstall Battery Cover.For answers to questions, call 1-800-35 GENIE, or visitwww.geniecompany.comAdditional Genie® products can be ordered using the Accessoriespage in your Owner’s Manual or through the 800 number above.FOR CONVENIENCEProgram Keypad BEFORE mounting.SECTION1SECTION2SECTION3BASICADDITIONAL OPERATIONSSECTION4USING A TEMPORARY PIN A temporary PIN allows temporary access to your home byrepair persons, meter readers, etc.AEnter your PIN•Press .BEnter the Temporary PIN (from 3 to 8 characters).•Press .NOTE•DO NOT reprogram the Door Opener(s).•Temporary PIN remains active until the next time your normal PIN is entered.FORGOT YOUR PINORCHANGING YOUR PINAErase old PIN :•Press and hold in order - .–Red LED will blink once and turn off.•Release all buttons.BProgramming Door Opener(s).•Return to “Programming”Section 1 or Section 2.NOTE•If the door does not move, check the red LED on Keypad.If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking,re-enter your PIN and try again.•Any Keypad Button will control the door for 30 seconds after the door starts moving.•Rapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over.Wallscrew head gapFigure 1FOR CONVENIENCEProgram Keypad BEFORE mounting.STEP 2: PROGRAMMING THE KEYPAD FORMULTIPLE DOOR OPENERSAAll door openers will use the same PIN.•Enter your PIN and press .– Red LED blinks - once per second.•Press again.–Red LED blinks - twice per second.•Press the number of doors (total) you wishto control ( or ).•Press .–Red LED blinks several times and turns off.ProgramButtonFEATURES :TOOLS NEEDED:If Safety Reverse does not work properly:1Close door and disconnect the Opener using Emergency Release Cord.2Do not use door Opener, Remote Controls, or Wireless Keypad.3Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.1"8Printed in the U.S.A.©2003 The Genie Company, D.B.A. GMI Holdings, Inc.FCC and IC CERTIFIEDThis device complies with FCC Part 15 and RSS 210 of Industry Canada.This equipment has been tested andfound to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits aredesigned to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1.Re-orient or relocate the receiver antenna. 2.Increase the separation between the opener and receiver. 3.Connect theopener into an outlet on a circuit different from that to which the appliance is connected. 4.Consult the dealer.Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.CHANGING BAT TERYIf the red LED does not blink during use,the battery needs to be changed.1234567890DEFGHI JKL MNOPQRSTUVWXYZPROG9VBatteryPress hereFigure 2BottomMountingScrewRed LEDCovers available in:• Almond (P/N 00000)• Sandstone (P/N 00000)• Brown (P/N 00000)

Navigation menu