The Genie a Division of Overhead Door ACSDA1 GARAGE DOOR OPENER TRANSMITTER User Manual WK4 Page 1
The Genie Company a Division of Overhead Door Corporation GARAGE DOOR OPENER TRANSMITTER WK4 Page 1
USERS MANUAL
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 367768 |
| Application ID | KoNhhhCyzfyPYXELLUuZtg== |
| Document Description | USERS MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 12.66kB (158189 bits) |
| Date Submitted | 2003-10-23 00:00:00 |
| Date Available | 2003-10-23 00:00:00 |
| Creation Date | 2003-10-21 07:33:36 |
| Producing Software | Acrobat Distiller 5.0.5 for Macintosh |
| Document Lastmod | 2003-10-21 07:33:36 |
| Document Title | WK4 (Page 1) |
| Document Creator | QuarkXPress(tm) 5.01 |
FEATURES : 3528135342 • Ability to Control up to three • Genie® INTELLICODE® Openers Simple to Program and Install PIN Codes can be up to 8 Characters Low Battery Power Indicator Stays Programmed During Battery Change Temporary PIN for Special Purpose Access TOOLS NEEDED: This Wireless Keypad is compatible with all INTELLICODE® radio equipped GENIE® products. • • • • Red LED indicates Battery Power and Status during Use and Programming Drill with 1/16" Drill Bit Phillips Screwdriver Pencil Mounting Screws INCLUDED inside Battery Compartment OPERATING INSTRUCTIONS (KEEP FOR FUTURE REFERENCE) WARNING SECTION PROGRAMMING FOR 2 2 OR 3 DOOR OPENERS Program Keypad BEFORE mounting. Program Keypad BEFORE mounting. STEP 1: SETTING YOUR WIRELESS KEYPAD PIN STEP 1: SETTING YOUR WIRELESS KEYPAD PIN (PERSONAL IDENTIFICATION NUMBER) Activate programming mode. • Press (in order) – Red LED blinks - once per second. • Enter your PIN (3 to 8 characters). • Enter your PIN (3 to 8 characters). • Press • Press STEP 2: PROGRAMMING ONE DOOR OPENER Find the Learn Code Button and Learn Code Indicator LED on your door opener. – If your door opener has a black antenna wire, Red Indicator the Learn Code Button LED and Indicator LED are located near the antenna. (The light lens may need to be opened.) Located – If your door opener does not have an antenna, you have an external receiver. The external receiver cover must be removed to access the Learn Code Button and Indicator LED. STEP 2: PROGRAMMING THE KEYPAD FOR MULTIPLE DOOR OPENERS – Red LED blinks - twice per second. • Press the number of doors (total) you wish • Press Learn Code Button – Learn Code Indicator LED (on Opener) will blink. or on keypad. STEP 3: ¤ 9V MOUNTING INSTRUCTIONS Erase old PIN : – Red LED will blink once and turn off. • Release all buttons. PROGRAMMING DOOR OPENERS Programming Door Opener(s). USING A TEMPORARY PIN A temporary PIN allows temporary access to your home by repair persons, meter readers, etc. Decide which door will be door #1,#2 and #3. • Press the Learn Code Button (see Section 1 Step 2). – Learn Code Indicator LED (on Opener) blinks. again. • Enter your PIN and press OPERATING ONE DOOR OPENER door Opener ( • Press or or • Press NOTE • DO NOT reprogram the Door Opener(s). • Temporary PIN remains active until the next time your normal PIN is entered. CHANGING BATTERY Repeat step A above for each door opener. Each door opener must be programmed to receive the signal from the Wireless Keypad. (P/N 00000) • Sandstone 9V Battery DEF GHI JKL MNO PQRS TUV WXYZ Bottom Mounting Screw Press here (P/N 00000) To move one of the doors. • Brown (P/N 00000) • Enter your PIN. FCC and IC CERTIFIED • Press door opener number ( or or For answers to questions, call 1-800-35 GENIE, or visit www.geniecompany.com Additional Genie® products can be ordered using the Accessories page in your Owner’s Manual or through the 800 number above. Covers available in: • Almond STEP 4: OPERATING 2 OR 3 DOOR OPENERS • Press PROG If the red LED does Figure 2 not blink during use, the battery needs to Red LED be changed. • If the door does not move,check the red LED on Keypad. NOTE ). – Learn Code Indicator LED turns off. Proceed to Section 3 - Mounting Instructions. Enter the Temporary PIN (from 3 to 8 characters). • Press – Learn Code Indicator LED stays on. • Enter your PIN. If the LED is blinking rapidly,the PIN was entered incorrectly. After the LED stops blinking,re-enter your PIN and try again. • Any Keypad Button will control the door for 30 seconds after the door starts moving. • Rapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over. Enter your PIN • Press the number you have picked for this To move the garage door: ©2003 The Genie Company, D.B.A. GMI Holdings, Inc. – Learn Code Indicator LED stays on. • Press ). – Learn Code Indicator LED turns off. • Press and hold in order - – Red LED blinks several times and turns off. – Learn Code Indicator LED stays on. STEP 3: WXYZ • Return to “Programming”Section 1 or Section 2. • Press the Learn Code Button. • Press again. to control ( TUV FORGOT YOUR PIN OR CHANGING YOUR PIN – Red LED blinks - once per second. • Press PQRS SECTION BASIC 4 ADDITIONAL OPERATIONS All door openers will use the same PIN. • Enter your PIN and press on Opener Housing • Enter your PIN and press – Red LED blinks - twice per second and turns off. – Red LED blinks - twice per second and turns off. Activate programming mode. • Press (in order) – Red LED blinks - once per second. MNO The Keypad must be mounted in sight of the door(s), at least 5 feet above the ground and clear of any moving door parts. A Mount Keypad.(Mounting screws located inside battery compartment.) • Remove Battery Cover. See Section 4 Figure 2. • Drill a 1/16”pilot hole for the top mounting screw. • Install a screw into the drilled Figure 1 hole,leaving a 1/8" gap between the screw head 1" and the wall. See Figure 1. Wall • Hook the Keypad over the screw. • Mark,drill pilot hole and fasten bottom screw. screw head gap • Reinstall Battery Cover. (PERSONAL IDENTIFICATION NUMBER) JKL SECTION FOR CONVENIENCE FOR CONVENIENCE DEF GHI Program Button Backlit Keypad for Ease of Use at Night Battery Compartment 9 Volt Battery (included) If Safety Reverse does not work properly: 1 Close door and disconnect the Opener using Emergency Release Cord. 2 Do not use door Opener, Remote Controls, or Wireless Keypad. 3 Refer to Door and Door Opener Owner’s Manuals before attempting any repairs. A Moving door can cause serious injury or death. 1 Keep people clear of opening while door is moving. 2 Do Not allow children to play with Wireless Keypad. 3 During programming, the door opener could begin to run, so stay away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the Opener by pulling the Emergency Release. SECTION PROGRAMMING FOR 1BASIC O NE DOOR OPENER Instructions • • • • Interchangeable Flip-up Cover available in 3 optional Classic Colors to match your home’s exterior decor SEE NOTE AT BOTTOM OF SECTION 1 Proceed to Section 3 - Mounting Instructions. ). This device complies with FCC Part 15 and RSS 210 of Industry Canada.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Re-orient or relocate the receiver antenna. 2. Increase the separation between the opener and receiver. 3. Connect the opener into an outlet on a circuit different from that to which the appliance is connected. 4. Consult the dealer. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Printed in the U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2003:10:21 07:33:36Z Modify Date : 2003:10:21 07:33:36Z Creator : QuarkXPress(tm) 5.01 Page Count : 1 Creation Date : 2003:10:21 07:33:36Z Mod Date : 2003:10:21 07:33:36Z Producer : Acrobat Distiller 5.0.5 for Macintosh Metadata Date : 2003:10:21 07:33:36Z Title : WK4 (Page 1)EXIF Metadata provided by EXIF.tools