The Kroger SZMDLNR1 CC2530 ZigBee Module User Manual 5 SRNMRG Module Manualx

Download:
Mirror Download [FCC.gov]
Document ID	1825323
Application ID	6nNhqLna7ZAkaV7i2w3NQA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.88kB (148457 bits)
Date Submitted	2012-10-29 00:00:00
Date Available	2012-10-31 00:00:00
Creation Date	2012-10-29 14:28:04
Producing Software	GPL Ghostscript 8.64
Document Lastmod	2012-10-29 14:28:04
Document Title	Microsoft Word - 5_SRNMRG Module Manual.docx
Document Creator	PScript5.dll Version 5.2
Document Author:	chirag.solanki

SRNMRG User Guide
SRNMRG
(CC2530 ZigBee MODULE)
USER GUIDE
Rev 1.2
Page 1
SRNMRG User Guide
Contents
Introduction .......................................................................................................... 4
1.1
Purpose and scope .................................................................................................. 4
1.2
Revision History ...................................................................................................... 4
Module Application Circuit ..................................................................................... 5
2.1
Sample Application Connections ............................................................................. 5
2.2
Compliance Limits ................................................................................................... 6
2.3
Module Power Supply ............................................................................................. 6
Antenna Options and PCB Footprint........................................................................ 7
3.1
Footprint Overview ................................................................................................. 7
3.2
Module Footprint.................................................................................................... 8
Agency Statements ................................................................................................ 9
4.1
Federal Communication Commission Interference Statement................................. 9
4.2
ETSI (European Telecommunications Standards Institute) Statement ..................... 9
4.3
RF Exposure ............................................................................................................ 9
4.4
End Product Labelling............................................................................................ 10
Contact Detail ..................................................................................................... 11
Rev 1.2
Page 2
SRNMRG User Guide
Figures
Figure 1: SRNMRG Application Circuit ................................................................................... 5
Figure 2: Header Board Footprint Overview .......................................................................... 7
Figure 3: SRNMRG Module Footprint overview ..................................................................... 8
Tables
Table 1: Compliance Limit ..................................................................................................... 6
Rev 1.2
Page 3
SRNMRG User Guide
1 Introduction
1.1 Purpose and scope
The purpose of this document is to provide details regarding the use of CC2530 ZigBee
Module (SRNMRG). This document describes the connections between CC2530 Module and
header board. This connection details can be used to mount Module on other Host Board.
1.2 Revision History
Date
14-Sep-2012
15-OCT-2012
29-OCT-2012
Rev 1.2
Change Description
Revision
Initial release
Sec 2.2 Updated
Sec 2.2 Updated for
compliance note
1.0
1.1
1.2
Page 4
SRNMRG User Guide
2 Module Application Circuit
2.1 Sample Application Connections
Figure 1 shows the circuit connection between SRNMRG Module and CC2530 Header board.
Header board provide the power supply to the SRNMRG Module and also debug header for
programming the CC2530.
Figure 1: SRNMRG Application Circuit
Please refer SRNMRG datasheet for module pin description. Based on application
requirements host device can be interfaced with other pins on the module. Please refer TICC2530 user guide for connection/state information of unused pins.
Rev 1.2
Page 5
SRNMRG User Guide
2.2 Compliance Limits
Depending on the country where the module is used, proper power level needs to be set to
meet compliance limit to ensure the certification of module.
Table 1 shows the register value configuration for RF Power to meet compliance limit for
ETSI standard.
Table 1: Compliance Limit
Compliance
TX POWER Register value
ETSI
0XF5
Note: The register value used for FCC compliance is maximum value and cannot be
increased by end user. The RF Output Power configuration is not accessible to End User.
2.3 Module Power Supply
The SRNMRG Module can operate between 2.7V to 3.6V power level. However, it is
recommended to provide nominal 3.3VDC supply to Module VCC and GND pins. For details
of VCC – GND pins; please refer Module datasheet.
Rev 1.2
Page 6
SRNMRG User Guide
3 Antenna Options and PCB Footprint
SRNMRG (CC2530 Module) has PCB Inverted F Antenna designed on Board.
3.1 Footprint Overview
Below figure shows the footprint detail of the Header board for SRNMRG Module. The
Header Board (or Host Board) Footprint will be designed as per the Module footprint as
mentioned in datasheet.
Figure 2: Header Board Footprint Overview
Rev 1.2
Page 7
SRNMRG User Guide
3.2 Module Footprint
Figure 3 shows the Module footprint over the Header board
Figure 3: SRNMRG Module Footprint overview
SRNMRG User Guide
4 Agency Statements
4.1 Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates; uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
4.2 ETSI (European Telecommunications Standards Institute) Statement
This device has been tested and certified for use in the European Union. If this device is used
in a product, the OEM has responsibility to verify compliance of the final product to the EU
standards.
4.3 RF Exposure
This module has been certified for remote and base radio applications and is not intended
to be operated within 20 cm of the body. If the module will be used for portable
applications, the device must undergo SAR testing.
Rev 1.2
Page 9
SRNMRG User Guide
Following instruction can be included in Final product user manual.
Instruction: To satisfy FCC RF exposure requirements for mobile transmitting devices, a
separation distance of 20 cm or more should be maintained between the antenna of this
device and persons during operation. To ensure compliance, operations at closer distances
than this are not recommended.”
4.4 End Product Labelling
The SRNMRG Module is labelled with its own FCC ID. If the FCC ID Certification Number is
not visible while installed inside another device, then the device should display the label on
it referring the enclosed module. In that case, the final end product must be labelled in a
visible area with the following:
“Contains Transmitter Module FCC ID: PBR-SZMDLNR1”
OR
“Contains FCC ID: PBR-SZMDLNR1”
The OEM should not provide information to the end user regarding installation or removal
of this RF module or change RF related parameters in the user manual of the end product.
The OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device
emissions, PC peripheral requirements, etc.).
Rev 1.2
Page 10
SRNMRG User Guide
5 Contact Detail
The Kroger Co.
11450 Groom Road
Blue Ash, OH-45242,
USA
Rev 1.2
Page 11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 11
Producer                        : GPL Ghostscript 8.64
Create Date                     : 2012:10:29 14:28:04+05:30
Modify Date                     : 2012:10:29 14:28:04+05:30
Title                           : Microsoft Word - 5_SRNMRG Module Manual.docx
Creator                         : PScript5.dll Version 5.2
Author                          : chirag.solanki

EXIF Metadata provided by EXIF.tools