The Watt Stopper TDWALL MRD2, MRD3, MRD4, MRD5, MRD6, MRD8, MRD9 User Manual MRD6 Wireless Room Preset

The Watt Stopper, Inc. MRD2, MRD3, MRD4, MRD5, MRD6, MRD8, MRD9 MRD6 Wireless Room Preset

Contents

User Manual MRD6

2, 4 3 3 Ø × Note: when you see Ú in the instructions, press the top and the bottom of the device rocker at the same time 3 How to install and use the wireless MiroTM room preset controller (MRD6) English Read and retain these instructions Français Español Ready? Application For more information on designing, installing and using wireless MiroTM systems, and for expert technical help, call 1-800-223-4185, or visit our web site at: www.passandseymour.com/miro Use one or more wireless MiroTM room preset controllers in a room with any number of wireless MiroTM dimming or non-dim devices. Used this way, the wireless MiroTM room preset controller provides instant recall of four user-recorded lighting scenes (or presets), plus off, as well as an overall mastering of the room’s light level. Need more than four scenes? Use two or more wireless MiroTM room preset controllers for up to sixteen recordable scenes per room! (explanation below). The wireless MiroTM room preset controller may be combined with the following wireless MiroTM control devices to control a room:  Incandescent Dimmers  Universal Dimmers  High Power Wall-mount Dimmers  Non-dim Switches  Silent Fan Controls  Plug-in Lamp Modules  Plug-in Appliance Modules  Remote Actuators  Handheld Room Remote Control Note: for whole-house control, use a wireless MiroTM whole-house preset controller Installation 1. Disconnect power to circuit by turning circuit breaker OFF before installation. 2. Remove existing wall plate and switch. 3. Strip existing wires ½” 4. Wire the LINE (black), NEUT (white), and GND supply wires to the correspondingly marked screw terminals, following the wiring diagram in figure 1 5. Mount using a MiroTM wall plate, following instructions provided 6. Switch the circuit breaker back ON INSTALL IN COMPLIANCE WITH ALL APPLICABLE CODES & STANDARDS. Failure to follow these instructions may cause personal injury or equipment damage. Get Set… Configuration Figure 2 To prevent interference between neighboring systems, wireless MiroTM devices must acquire a unique house ID before use. It’s simple! 1. With all devices installed and energized, check that every wireless MiroTM device is showing a yellow LED. If not, check that the circuit breaker is on and that the device is correctly installed. 2. All devices in a home must be ‘bound’ to the same home ID. For a new wireless MiroTM installation, simultaneously press and hold the top and bottom (Ú) of any device paddle for 2 seconds. Its LED flashes yellow, indicating that it has acquired a unique House ID. 3. Check that all other wireless MiroTM device LEDs are flashing green, indicating that they have acquired the same House ID. 4. Return to the first device, and press Ú again for 2 seconds. All device LEDs revert to green, indicating that house binding is complete. Note: if you’re adding the device to an existing wireless MiroTM installation, simply GND NEUT LINE Figure 1 Supply Wire
1 2, 4, 6 1 5 press and hold Ú on any previously bound device for 2 seconds to start the procedure, verify that the newly added device LED is flashing green, indicating that it has acquired the House ID. Press and hold Ú for 2 seconds again on the same previously installed device to terminate. Room Setup Figure 3, Room Binding When all the wireless MiroTM devices in the room are successfully bound to the House ID, it’s time to bind them together as a Room. The procedure is the same, but it must start from a wireless MiroTM room preset controller. 1. Go to the nearest wireless MiroTM room preset controller, and press Ú for 2 seconds. Its LED starts flashing yellow, and all the others start flashing green. 2. Go to each other wireless MiroTM device in the Room and press Ú for 2 seconds. The LED of each device starts flashing yellow as you add it to the Room. Be sure to bind every wireless MiroTM device in the Room. (If you miss one, you can repeat the procedure any time. Use Ú to toggle devices in and out of the Room. Flashing yellow LED = in, flashing green LED = out.) If you’re binding a Group into a Room, it’s only necessary to select one Group member. 3. Return to the first device and press Ú for 2 seconds to terminate Room binding. All Room devices revert to green status LEDs. Go! Use Figure 4 Figure 5 Setting up, recalling and modifying scenes is really easy: 1. Go around the room and set light levels to desired intensity 2. Press and hold a preset button for two seconds – until the status LED flashes once – to record the present scene in that preset. Note that the bottom preset button is always OFF, and may not be recorded. 3. Create different looks for different occasions, uses or times of day, and record them in the other preset locations. Note that if you have more than one wireless MiroTM room preset controller, you still only need record scenes once – they’ll recall from the same button on any controller in the room. 4. To recall a recorded scene, just press the appropriate preset button, and watch the scene smoothly transition from the previous lighting state. 5. To raise or lower the lighting levels in the room, press the raise/lower rocker on the wireless MiroTM room preset controller. 6. To modify a recorded scene, adjust lighting levels, and press the appropriate preset button for two seconds – until the status LED flashes once. Handheld Remote Control wireless MiroTM handheld room remote control You can have a lot of fun with a wireless MiroTM handheld room remote control! This handy unit sits right there on the coffee table, allowing you to adjust individual or room light levels, set and recall scenes, and even adjust ceiling fan speeds. Ask your wireless MiroTM supplier for a handheld room remote control to add the finishing touch to your wireless MiroTM installation! 1, 3 2 2 2 2 2 Status LED Raise/Lower Rocker Preset Buttons 1-4 (recordable) OFF button (not recordable)
Press Ú and preset B simultaneously to cause the controller to record and recall scenes 5-8 The remote switch mounts on the wall and looks just like a dimmer. But actually it’s Grouped with the lamp module behind the sofa! Now, the lamp plugged in to the lamp module is seamlessly controlled by the remote actuator on the wall -– just as if its own buttons were being pressed! 1 3 4 2 3 Advanced Users More Scenes Figure 6 You can increase the number of scenes in a room up to a total of 16. You will need one wireless MiroTM room preset controller for each four scenes. Install as described above, then set the controllers to be used for scenes above 4 as follows: Simultaneously press Ú and one of the following preset buttons for 2 seconds, to set the scenes to be controlled by each controller:  A (top) = scenes 1-4 (default)  B = scenes 5-8  C = scenes 9-12  D = scenes 13-16 Groups in Rooms Figure 7 You may want to combine wireless MiroTM Groups within Rooms. A typical example would be using a wireless MiroTM plug-in lamp module, grouped with a wireless MiroTM remote switch, providing convenient wall control of that lamp module that ended up behind the sofa – it happens! Simply configure the Group, following the instructions provided with the ‘groupable’ devices, then make sure you include one of the Group members in the room binding (see above). Now, you have the convenience of Group operation – it’s easy to control the concealed lamp module – and the sophistication of Room-level scene control. It’s so easy with wireless MiroTM. Excluding devices from a Room preset Figure 8 When wireless MiroTM records a Room scene, or preset, all devices bound into the Room acquire a level (or on/off status) associated with that scene. Therefore, when the scene is recalled, all devices in the Room move to their recorded levels. In certain circumstances it may be preferable to exclude a specific device from a room scene, so that it is unaffected when the scene is recalled. Examples might include step and pathway lighting circuits, or decorative neon fixtures, fountain pumps and the like. Use this procedure to exclude one or more circuits from a given preset. Note that the circuits will still fade or switch off when you press the bottom (off) preset button. 1. Go to the nearest wireless MiroTM room preset controller, and press Ú for 2 seconds 2. On the same wireless MiroTM room preset controller, press the appropriate preset button. The LEDs on all devices included in the preset start flashing yellow. 3. Go to each wireless MiroTM device in the Room that you want to exclude from the preset, and press Ú. The LED of each excluded device starts flashing green. Note that you can toggle a device in and out of the scene by pressing the preset button. 4. Return to the first device and press Ú for 2 seconds to terminate. All Room devices revert to green status LEDs.
Cleaning Clean only using a cloth dampened with water and a little mild detergent. Use of solvents or hydrocarbon-based cleaners may cause permanent damage. Troubleshooting Problem: At house binding, not all the wireless MiroTM devices in the house are flashing green. In larger homes, some of the devices may be out of range of the initiating device. In this case, it will be necessary to add a wireless MiroTM Radio Repeater to boost radio signal range. Problem: I messed up the configuration, and I need to clear down and start again. You can reset any wireless MiroTM device to factory default settings by pressing and holding for 10 seconds. The LED reverts to yellow, indicating that factory settings have been restored. FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by Pass & Seymour/Legrand could void your authority to operate this equipment.
Lifetime Warranty MiroTM is much more than lighting control! For information on MiroTM wiring devices, decorative wall plates, home networks and home automation solutions, visit our web site at www.passandseymour.com/miro The device you have purchased is warranted under normal use against defects in workmanship and materials for as long as you own the device. If the device fails due to manufacturing defect during normal use, return the device for replacement to the store where purchased or send to: Pass & Seymour/Legrand, Inc., 50 Boyd Avenue, Solvay, NY 13209. All requests for replacement must include a dated sales receipt (legible copies acceptable). ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF TWO YEARS FROM THE DATE OF PURCHASE. YOUR SOLE AND EXCLUSIVE REMEDY AGAINST PASS & SEYMOUR/LEGRAND UNDER ANY WARRANTY SHALL BE THE EQUIVALENT REPLACEMENT OF THE DEVICE. IN NO EVENT SHALL ANY WARRANTY APPLY TO ANY DEFECT ARISING OUT OF ANY ALTERATION OF THE DEVICE, IMPROPER INSTALLATION, MISUSE, ABNORMAL USE OR NEGLIGENCE. IN NO EVENT SHALL PASS & SEYMOUR/LEGRAND BE LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations of incidental or consequential damages. Some of the above limitations or exclusions may not apply to every purchaser. © 2003 Pass & Seymour/Legrand, Inc., PO Box 4822, Syracuse, NY 13221-4822. P/N MRD6 rev 3. Go to www.passandseymour.com/miro for MiroTM system guide and technical support.

Navigation menu