The Whistler Group WH17 Radar Detector User Manual Manual

The Whistler Group Radar Detector Manual

Manual

Download: The Whistler Group WH17 Radar Detector User Manual Manual
Mirror Download [FCC.gov]The Whistler Group WH17 Radar Detector User Manual Manual
Document ID638415
Application ID9g/OsCsuIbrt9KnEelxUyg==
Document DescriptionManual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize17.1kB (213696 bits)
Date Submitted2006-03-20 00:00:00
Date Available2006-03-20 00:00:00
Creation Date2006-03-01 08:07:14
Producing SoftwareQuarkXPress(tm) 6.5
Document Lastmod2006-03-01 08:08:25
Document TitleManual
Document CreatorQuarkXPress(tm) 6.5

POP MODE ALERTS
™
Because POP Mode travels on regular radar
bandwidth, there is no particular alert for POP™
Mode transmissions. POP™ Mode alerts will be
displayed as a regular radar alert.
™
Safety Warning System
™
In communities where transmitters are located,
the Safety Warning System™ displays over 60 text
messages. When Safety Radar is detected, the
audio alert is geiger counter-like.
Safety Warning System Text (XTR-520 Only)
Example: Poor - Road - Surface.
• XTR-220 Model displays a “S.” to indicate
a SWS™ message has been received.
NOTE: Not all areas have Safety Warning
System™ transmitters.
LASER/RADAR ALERTS
Speed Radar Audio/Visual Alerts
When X, K, or Ka is detected, the band ID and
signal strength are displayed. The audio alert is
continuous and has a geiger counter-like
pattern. The faster the beep, the closer or
stronger the radar source.
Laser Audio/Visual Alerts
When a laser signal is detected, the audio alert is
continuous for a minimum of 3 seconds.
• Model XTR-520 displays:
The more “|||”, the closer the laser source.
• Model XTR-220 displays:
14
SPEED MONITORING
Laser Facts
It’s well documented that many radar guns
cannot reliably provide the speed of a targeted
vehicle that is traveling in a group of vehicles. In
contrast, a laser gun can target a specific vehicle
out of a line of traffic and determine its speed.
The advantage of laser over radar in terms of
target identification is the result of the laser gun’s
narrow beam. A radar transmission can cover
more than a four-lane highway at a distance of
1,000 feet, compared with a laser transmission
which covers about 3 feet at the same distance.
For best protection, keep these points in mind:
• Because your vehicle’s license plate or
headlights are the laser gun’s primary targets,
mounting your Whistler detector on the
dashboard can improve laser detection at
short range.
• Do not follow closely behind any vehicle you
cannot see through. If you can’t see past a
vehicle ahead of you, chances are your
detector won’t either.
• The receiving range of your laser detector will
not be the same as a radar detector. Laser
guns are most often used at short range.
Whistler Laser-Radar detectors receive all
current laser guns which operate at a laser
wavelength of 905 +/- 10mm.
•Pro Laser™ I II III •LT1 20-20
•Ultra Lyte
Laser Tips
LASER/RADAR ALERTS
If you are the targeted vehicle, a laser gun can
often determine your speed within a few
seconds after you receive an alert. In this
situation there is generally no time to safely
adjust your speed. However, if you are traveling
near or behind the targeted vehicle and receive
an alert, response time should be sufficient. Any
laser alert, regardless of duration, requires
immediate action!
21
VG-2 ALERTS
Alert Priority
Pulse Protection®
POP™ Mode Alerts
Pulse (or instant-on) radar is more difficult to
detect than conventional radar because it
remains ‘off’ until activated to measure the speed
of a targeted vehicle.
When a pulse type transmission is detected, your
Whistler detector sounds an urgent 3-second
audio warning and:
• Model XTR-520 displays:
• Model XTR-220 displays:
After the 3-second pulse alert, the standard alert
pattern continues for as long as the signal is
present.
It is important to respond promptly to a pulse
alert, since warning time may be minimal.
VG-2 Audio/Visual Alerts
NOTE: You must turn this feature on before it
will detect VG-2.
When a VG-2 signal is detected, the detector ‘hides’ its
own radiated signal and becomes undetectable by
the VG-2.
Once VG-2 is detected, every 30 seconds, the
detector checks for a VG-2 signal. If a VG-2 signal
is still present, the unit continues to hide and
repeats the VG-2 alert. If no signal is detected, two
beeps are provided, indicating an ‘all clear’ condition.
During VG-2 Alert X, K, and Ka band signals
cannot be received (Reference page 19 for VG-2
information).
NOTE: Having a radar detector capable of detecting
the VG-2 may alert you to the presence of a speed
trap. As of this printing , the newest tool Police have to
detect radar detectors is called Spectre, as of this
printing. Spectre can detect all undetectable (VG-2)
laser/radar detectors on the market.
15
When two or more signals are received at the
same time, the alert priority is:
1. Laser
2. VG-2
3. Speed Radar
4. Safety Radar
Example:
If X band is alerting, then suddenly VG-2 is
detected, the VG-2 warning will override the X
band alert.
Reset Features
All user features can be reset to factory settings.
• Unplug Power Cord from unit.
• Plug Power Cord into unit.
Unit is now reset.
Default factory settings are:
1. Audio to level (5).
2. Display reads Highway. (XTR-520 only)
’H’ illuminates on XTR-220
3. Dim/Dark Mode to Dim-Bright
4. Auto Quiet Mode OFF.
5. VG-2 Detection Mode OFF.
6. Safety OFF.
7. Vehicle Battery Saver ON.
8. Full Power Up sequence.
9. Default TONE 3.
10. POP ON
11. Voice On (XTR-520 only)
• Pacing - A patrol car drives behind you and
matches your driving speed.
• Vascar/Aircraft - The time it takes a vehicle to
travel a known distance is measured.
WARRANTY INFORMATION
Consumer Warranty
This Whistler Laser-Radar detector is warranted
to the original purchaser for a period of one year
from the date of original purchase against all
defects in materials and workmanship. This
limited warranty is void if the unit is abused,
modified, installed improperly, if the housing has
been removed, or if the serial number is missing.
There are no express warranties covering this product
other than those set forth in this warranty. All
express or implied warranties for this product are
limited to the above time. Whistler is not liable
for damages arising from the use, misuse, or
operation of this product.
NOTE: Any damage to the remote battery or
battery leakage, water damage or any physical
damage is not covered under the warranty.
Check with the battery manufacturer about this
warranty.
22
• Check fuse in Whistler plug; replace if necessary with
a 2 amp 3AG type.
• Check fuse for lighter socket; replace if necessary.
• Make sure lighter socket is clean.
PROBLEM: The unit alarms when vehicle hits
bumps.
• Check for loose lighter socket; tighten and clean.
• Check connections at both ends of power cord.
Substitute another cord to determine if cord is
defective. Return defective cord to the factory.
PROBLEM: The unit alarms when using vehicle
electrical accessories (brakes, power mirrors,
power windows, turn signals, horn, etc.).
• Vehicle’s electrical system, including battery and
alternator, may have electrical noise. Install a filter
capacitor (470mfd. 25 volt or larger capacitance value)
on the back of the lighter socket.
PROBLEM: The remote no longer controls the
detector
• Make sure the remote is pointed at the front display.
• Possible weak or dead remote battery, replace battery.
CARE AND MAINTENANCE
16
WARRANTY INFORMATION
Service Under Warranty
During the warranty period, defective units will
be repaired without charge when returned with a
dated store receipt to the address below. Units
returned without dated store receipt will be
handled as described in section “Service Out
Of Warranty.” Due to the specialized equipment
necessary for testing a Laser-Radar receiver, there
are no authorized service stations for Whistler
brand detectors other than Whistler.
When returning a unit for service, please follow
these instructions:
1.
Ship the unit in the original carton or in a
suitable sturdy equivalent, fully insured, with
return receipt requested to:
NOTE: It is the responsibility of the individual
During the summer months, avoid prolonged
exposure to direct sunlight by removing your unit
from the dash when your vehicle is parked for an
extended period of time. Do not spray water,
cleaners, or polishes directly onto the unit. The
spray may penetrate through the openings and
damage the unit. Also, do not use any abrasive
cleaners on the unit’s exterior.
(1) This device may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
Radar Facts
ARE DETECTORS LEGAL?
In Most States YES!
Laser-Radar detectors are legal in every state
(with the exception of Virginia and Washington,
D.C., which have local regulations restricting the
use of radar receivers in any vehicle) when used
in automobiles or light trucks (under 10,000 lbs.).
Concerning trucks over 10,000 lbs., the Federal
Highway Administration (FHWA) issued a
regulation, effective January, 1994 which prohibits
radar and laser detector use in these types of
vehicles nationally. Prior to the FHWA regulation,
laws existed in the state of New York restricting
the use of radar detectors in trucks over 18,000
lbs. and in Illinois in trucks over 26,000 lbs.
• Cancel Auto Quiet Mode or City Mode.
• Check audio level setting (see page 7).
Whistler Repair Dept.
1201 North Dixieland Rd
Rogers, AR. 72756
Please allow 3 weeks turnaround time.
IMPORTANT: Whistler will not assume
responsibility for loss or damage incurred in
shipping. Therefore, please ship your unit
insured with return receipt requested. CODs
will not be accepted!
2. Include with your unit the following
information, clearly printed:
• Your name and street address (for shipping
via UPS), a daytime telephone number and
email address, if applicable.
• A detailed description of the problem (e.g.,
“Unit performs self-test but does not respond
to radar”).
• A copy of your dated store receipt or bill of
sale.
23
SPEED MONITORING
Radar Detector Detectors (VG-2)
The Interceptor VG-2, or simply VG-2, is a
microwave receiver used by police to detect
signals radiated by the local oscillator of a radar
detector. Because its purpose is to identify
persons driving with radar detectors, the VG-2 is
known as a ‘radar detector detector’.
The VG-2 is the primary tool used by the police
to identify radar detector equipped vehicles. If
caught in a state where detectors are illegal,
(see page 18), drivers risk losing their radar
detector and receiving a fine. In addition,
instant-on radar is almost always used in
combination with a VG-2, leaving unsuspecting
motorists vulnerable to receiving two tickets one potentially for speeding, the other for
possession of a detector.
WARRANTY INFORMATION
IMPORTANT: When returning your unit for
service, be certain to include a daytime
telephone number and an email address (if
applicable).
IMPORTANT: To validate that your unit is
within the warranty period, make sure you
keep a copy of your dated store receipt. You
may register your warranty online at
www.whistlergroup.com, however, for
warranty verification purposes, a copy of
your dated store receipt must accompany any
unit sent in for warranty work.
If you have questions concerning the operation of
your Whistler detector, or require service during
or after the warranty period, please call
Customer Service at: 1-800-531-0004
Representatives are available to answer your
questions Monday - Friday from 8:00 a.m. to 5:00
p.m. (CT) or visit the FAQ’s at
www.whistlergroup.com.
The minimum out of warranty service fee for
your Whistler detector is $55.00 (U.S.). If you
require out of warranty service, please return
your unit as outlined in the section “Service
Under Warranty” along with a certified check or
money order for $55.00. Payment may also be
made by MasterCard, VISA or American
Express; personal checks are not accepted.
In the event repairs cannot be covered by the
minimum $55.00 service fee, you will be
contacted by a Whistler technical service
specialist who will outline options available to
you. If you elect not to have your unit repaired,
it will be returned to you along with your
certified check or money order.
24
FCC requirements state that changes or
modifications not expressly approved by Whistler
could void the user’s authority to operate the
equipment.
18
3. Be certain your unit is returned with its serial
number. For reference, please write your unit’s
serial number in the following space: s/n_______.
Units without serial numbers are not covered under
warranty.
• A dated store receipt is not supplied.
• The unit has been returned without its serial
number.
• The unit has been abused, modified,
installed improperly, or had its housing
removed.
IMPORTANT
www.whistlergroup.com
17
Units will be repaired at ‘out of warranty’ service
rates when:
• The units original warranty has expired.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
Having a radar detector capable of detecting
the VG-2 may alert you to the presence of a speed
trap. For more information on speed monitoring
technologies, please visit our FAQ page on our
website:
If difficulties occur which cannot be solved by
Service Out of Warranty
SPEED MONITORING
FCC ID: HSXWH17
PROBLEM:The audio alerts are not loud enough.
WARRANTY INFORMATION
FCC INFORMATION
Care And Maintenance
information in this Troubleshooting Guide, please
call Whistler Customer Service at 1-800-531-0004
or visit our FAQ page at
www.whistlergroup.com/faq-detectors.asp,
before returning your unit for service.
SPEED MONITORING
Other Speed Detection Systems
Several techniques other than radar or laser are
used to measure vehicle speeds. When these
methods are being used, no detector can
provide a warning. These techniques include:
TROUBLESHOOTING
Your Whistler detector is expertly engineered
and designed to exacting quality standards to
provide you with reliable, trouble-free operation.
If your unit has been correctly installed following
the guidelines in this manual, but is not
operating optimally, please refer to the
troubleshooting guide below.
PROBLEM: No display or audio.
Customer Service
Laser Wavelength: 905 ± 50 nanometers (nm)
Radar Frequencies:
10.500 - 10.550 GHz (X Band)
24.050 - 24.250 GHz (K Band )
33.400 - 36.000 GHz (Ka Superwideband)
Operating Temperature Range: -20˚ C to +80˚
C (-4˚ F to +176˚ F)
Power Requirements:
Operational 12 to 15 volts DC, 250mA nominal
Vehicle Battery Saver, 30mA nominal.
Remote: 3V Coin Cell CR2032
One or more U.S. patents may apply:
#5,146,227, #5,379,456, #5,666,120, #5,990,821
Price
$ 9.95
$ 14.95
$ 15.95
$ 9.95
(for wiring to fuse box)
Modular Cord Package
$ 17.95
(includes coiled and straight cords,
and power adapter)
Package of 8 Suction Cups
Non-Skid Dash Pad
Straight Modular Cord &
Socket Multiplier
Coiled Modular Cord &
Socket Multiplier
Remote Control
Retractable Lanyard Key Ring
$ 2.95
$ 6.95
$ 11.95
XTR-220/520
Total Band Protection
LASER-RADAR
DETECTOR
The Whistler Group Corporate Headquarters
$ Call
$ Call
13016 N. Walton Blvd. • Bentonville, AR 72712
Tel 479.273.6012 • Fax 479.273.2927
Customer Return Center
1201 N. Dixieland Rd. • Rogers, AR 72756
Customer Service Tel 800.531.0004
www.whistlergroup.com
P/N 200010, © 2006 The Whistler Group, Inc.
26
™
$ 12.95
*Modular: Interconnecting pieces cord and plug. Shipping
and handling (per order) $5.00 Prices are subject to change
without notice.
POP™ Mode is a trademark of MPH Industries,
Inc. Specifications are subject to change
without notice.
25
Total Band Protection™
OWNER’S MANUAL
Windshield Bracket Kit
Straight Power Cord (5’)
Coiled Power Cord (7’)
Hardwire Kit (10' )
260251
260250
POP™ Mode is a feature on some newer radar
guns operating on K and Ka bands. When the
gun is in POP™ Mode and activated, a brief burst
of energy, less that 1/15 of a second, is
transmitted and the vehicle’s speed is quickly
acquired. A detector without POP™ Mode
detection capability cannot respond to this brief
transmission. This detector has the power to
report this new gun where other detectors
cannot!
ACCESSORIES
202151
206552
206553
206880
206661
POP™ Mode
20
Description
159032
402081
206660
Note: A radar detector will not alarm if an
officer is not transmitting on any one of the above
radar bands.
19
Order#
206666
A radar gun operates by transmitting radio
waves at certain frequencies which reflect off
objects and are then picked up by the radar
gun’s receiving section. When a radar beam
reflects off a moving target, a measurable
frequency shift occurs. The radar unit converts this
shift into miles per hour to determine your
vehicle’s speed. Currently, the FCC (Federal
Communications Commission) permits
operation of traffic radar guns at X Band (10.500
- 10.550 GHz), K Band (24.050 - 24.250 GHz), and
Ka Band (33.400 - 36.000 GHz).
Complete Band Coverage that detects laser,
radar, VG-2 and safety radar bands.
These and other accessories can be ordered
directly from Whistler by calling 1-800-531-0004 or
visit our online store at www.whistlergroup.com
SPECIFICATIONS
radar detector operator to know and understand
the laws in your area regarding the legality of the
use of radar detectors.
Dear Whistler Owner,
If you have questions concerning the operation of
this Whistler product please call:
CuSTOmer SeRVICE
1-800-531-0004
Monday - Friday • 8:00 am - 5:00 pm CT
or visit our website
www.whistlergroup.com
Please keep the receipt in a safe place. You may
whistlergroup.com.
register your product online at www.w
For warranty verification purposes, a copy of your dated
store receipt must accompany any unit sent in for
warranty work. If the unit is returned without a dated
store receipt an out of warranty service charge applies.
Note: Your warranty period begins at the time of
purchase. The warranty is validated only by the dated
store receipt! Please record the serial number of the
unit in the space provided in the warranty section of
the manual.
To fully acquaint yourself with the operation of your
Whistler laser radar detector we recommend reading
this entire manual or visiting our FAQ page on our
website www.whistlergroup.com
Enjoy your Whistler and please drive safely.
Sincerely,
The Whistler Group, Inc.
OPERATION
Replacing the Remote Battery
The remote control is powered by a 3 volt coin
type cell, model CR 2032. However, all batteries
eventually need replacing. When the time comes,
follow these steps:
• Remove the Phillips head screw located at the
bottom back side of the remote.
• Separate the two halves of the plastic case
• Gently lift out the PC board as the battery is
located opposite the buttons.
• The battery should slide out from its holder. Make
note of the correct polarity. Positive (+) is facing
away from the PC board.
• Insert the new battery, being mindful of the
correct polarity.
• Reassemble the reverse of disassembly
Setting Saver
Setting Saver saves your personalized settings so
that when the detector is turned off and then on
again, you do not have to re-enter them.
Feature Engaged Confirmation
Each time a button is pressed, one beep confirms
feature “on”, two beeps confirm feature “off”.
Audio Level Adjustment
Model Features Summary........................ 2 - 3
Installation............................................... 3 - 5
• Mounting Guidelines................................... 4
• Windshield Mounting.................................. 4 - 5
• Power Connection and Fuse Replacement..5
Operation................................................ 6 - 13
• Power On and Self-Test................................6
• Remote Control Operation.......................... 6
• Replacing the Remote Battery..................... 7
• Setting Saver.................................................7
• Feature Engaged Confirmation....................7
• Audio Level Adjustment..............................7
• Integrated Real Voice® ...................................7
• Auto Quiet Mode..........................................8
• Quiet Mode...................................................8
• City/City 1/ City 2 Mode............................9
• Highway Mode.............................................9
• Dim/Dark Mode.......................................... 9
• Teach/Tutorial Mode....................................10
• Engaging/Disengaging VG-2...................... 11
• Vehicle Battery Saver Mode......................... 11
• Option Select Mode (XTR-520 only)............ 12
• Stay Alert Feature.........................................13
POP™ Mode Alerts................................... 14
Safety Warning System™.......................... 14
Laser/Radar Alerts................................... 14 - 15
• Speed Radar Audio/Visual Alerts...............14
• Laser Audio/Visual Alerts...........................14
• Pulse Protection®...........................................15
VG-2 Alerts.............................................. 16
• Alert Priority.................................................16
• Reset Features...............................................16
Troubleshooting Guide............................ 17
Care and Maintenance............................. 18
Are Detectors Legal?............................... 18
FCC Information.......................................19
Speed Monitoring.................................... 19 - 22
• Radar Facts................................................... 20
• POP™ Mode...................................................20
• Total Band Protection™................................. 20
• Laser Facts.................................................... 21
• Other Speed Detection Systems.................22
Warranty Information...............................22 - 25
Specifications........................................... 25
Accessories.............................................. 26
OPERATION
Integrated Real Voice® (XTR-520 only)
When selected, Real Voice® will be used to
articulate the following:
1. Band Identification
2. Safety Warning System messages
3. Feature Selection
NOTE: In certain cases, the voice message does
not replicate the text message.
Auto Quiet Mode
Auto Quiet reduces the selected audio level to
level (1) approximately 5 seconds after a radar
or safety radar signal is detected. The alert for
any new signal within 20 seconds will resume at
level (1). Auto Quiet does not affect VG-2 or
laser alerts.
• Press Quiet/Menu (before a signal is detected)
to engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you
may cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
Quiet Mode
The audio levels can be adjusted high to low or
low to high two ways:
1. Press and hold the PWR/VOL ( VOL on XTR520) button and the volume level will increase
(Level 7) then proceed to lower the volume
(Level 0). Continuing to hold this button will
repeat the sequence. As audio level is adjusted,
beeps are provided and the display indicates
volume level.
2. Press either VOL UP or VOL DOWN on the
remote control.
Quiet cancels audio during an alert and any new
alert within 20 seconds. After 20 seconds,
approximately 2 beeps are provided on any
new alert and unit then remains quiet.
• Press Quiet to cancel the audio.
• Press Quiet a second time during an alert to
restore the standard audio alert pattern; or
turn the unit off, then on.
WHISTLER FEATURES
XTR-220
XTR-520
12
FEATURE DESCRIPTIONS
6.
12
10
9a
11b
11a
Accessories: Windshield Bracket Kit ,Power Cord & Remote Control
9b
10
10
13
FEATURE DESCRIPTIONS
Whistler’s ergonomic and user-friendly design provides
a new level of operating convenience. Special
features include:
Note: Not all units have all features listed.
1.
2.
3.
4.
5.
Bracket Release Button – Provides quick and
easy release of the mounting bracket.
Speaker – Provides distinct audio warnings for
X, K, Ka band radar, safety radar, laser and VG-2.
Mounting Bracket Location – Slot holds
mounting bracket firmly.
Radar Antenna – Compact, high-efficiency
antenna receives radar signals.
Front Laser Antenna – High gain optical lens
provides increased sensitivity and field of view for
leading-edge laser detection.
Rear Laser/ Remote Receiver – Receives laser
signals transmitted from the rear of the vehicle,
accepts input signals from the remote control.
7. City Button - Reduces the annoyance of false
alerts typically encountered in urban driving areas.
8. Quiet/Menu Button - Pressing QUIET before a
signal is detected engages Auto Quiet Mode
which automatically reduces the audio level after the
initial warning to a low audio level setting. Pressing
QUIET during a radar/laser encounter silences
audio alerts, while allowing visual alerts to keep
you informed. (Pressing and holding for 2
seconds allows you to enter Option Select Mode—
see page 12 (XTR-520 only.)
9. Power/Dim Dark - Turns unit on/off and
engages Dim/Dark modes (XTR-520 only.)
9a. Power/Volume - Turns unit on/off and
hold to adjust volume (XTR-220 only.)
9b. Power - Turns unit on/off
10. Volume Button – Adjust volume up or down.
11a. Text Display (XTR-520 only) – Provides distinct
visual confirmation of signals detected, signal
strength, and indicates engaged modes of
operation.
11b. 7 Segment Icon Display – Provides numeric
signal strength indicator and band identification.
12. Power Jack – Provides connection for the power cord.
13. Dim/Dark – Press and release button to select
Dim/Dark modes.
OPERATION
City/City 1/City 2 Mode
Whistler’s Three Stage City Mode is designed to
reduce the annoyance of automatic door
openers, intrusion alarms and other devices which
share frequencies with police radar. Generally X
band is used for these devices.
• Press City to cancel Highway mode and engage City.
• Press City a second time to engage City 1.
• Press City a third time to engage City 2.
• Pressing City a fourth time cancels City Modes and
returns the unit to Highway Mode.
In City Mode, a weak speed/safety radar signal
gives an initial alarm of two beeps, and then
remains quiet unless the signal becomes very
strong. When the signal strength increases, two
additional beeps are provided.
City 1 and CIty 2 Modes operate the same as
Highway Mode, but in City 1 Mode, only the X
band sensitivity is lowered. In City 2 Mode, Xband is not detected.
CAUTION: Some towns/small cities may still be
using X band radar. If Auto Quiet is engaged in
City 1 or City 2 modes and the unit receives a
strong radar signal, the unit performs the Auto
Quiet feature. City Modes do not change the
audio alert for laser or VG-2.
• Mount the unit as low as possible near the
center of the windshield.
• Do not mount your unit behind wipers,
ornaments, mirrored sunscreens, etc. These
obstructions have metal surfaces which can
affect radar and laser signals and reduce
critical warning time. (Regular tinted glass does
not affect reception.)
• Some windshields have an Instaclear™ or
Electriclear™ type coating, which affect radar
signals. Consult your dealer or your vehicle’s
owners manual to determine if your windshield
has this coating.
• Avoid placing unit in direct contact with
windshield.
• Avoid placing unit in direct sunlight
• To reduce the possibility of theft, conceal the
unit when not in use.
Windshield Mounting
• Install the two suction cups and rubber bumper
onto the bracket by fitting them into their
holes.
• Press the suction cups onto the windshield at
the location you have chosen.
IMPORTANT: Some newer cars have a plastic
safety coating on the inside of the windshield.
The windshield bracket may leave permanent
marks on this type of surface. To find out if your
vehicle has this type of windshield, check the
owner’s manual or ask your dealer. We
recommend that you do not leave the suction
cup bracket on the window in direct sunlight.
NOTE: On model XTR-220, City, Highway and
Dim/Dark modes are only engaged via the
remote control.
INSTALLATION
OPERATION
Highway Mode
Highway mode provides full audio warnings any
time radar (X, K, Ka, Safety Radar) or laser
signals are detected, and is recommended for
open road driving.
For more information on City and Highway mode,
please visit our FAQ page on our website:
www.whistlergroup.com
Dim/Dark Mode
Dim/Dark Mode reduces the illumination of the
display.
• Press and hold Power for 2 seconds to reduce
illumination to a Dim setting.
• Pressing and holding the power button for 2
seconds a second time engages Dark Mode.
The display illumination is further reduced.
Dim or dark can be engaged during an alert. In
Dark Mode, the display goes dark for as long as
a signal is being detected and for 20 seconds
after, then the display returns to the dimmer
setting.
• Pressing and holding the power button a
third time restores full illumination to the
display.
• Press the DIM button on the remote to select
display illumination.
Teach/Tutorial Mode (XTR-520 Only)
Provides simulated alerts for each type of signal.
• Press City and Quiet simultaneously and
release.
• Press Power to exit.
10
INSTALLATION
Windshield Mounting (Cont.)
If the detector is removed, this may cause
blistering of the dash in some vehicles.
• Slide the detector onto the bracket until it
locks into place.
• If necessary, the unit may be leveled by
bending the windshield bracket. Press the
bracket release button and remove the
detector before bending.
Power Connection
• Plug the small end of the power cord into the
unit’s power jack.
• Plug the large end into the vehicle’s cigarette
lighter.
NOTE: The cord fits tightly into detector.
When installing the cord, expect some
resistance.
Fuse Replacement
The lighter socket plug is equipped with a
replaceable 2 amp 3AG fuse located behind the
silver tip. To replace the fuse, carefully unscrew
the tip of the plug.
IMPORTANT: Unscrew slowly. The tip contains
a spring which may fly out when
disassembling.
Insert the new fuse with the spring and screw on
the tip. With use, the screw cap on plug may
loosen. Retighten it occasionally.
OPERATION
OPERATION
XTR-520: See option select mode to turn this
feature on.
XTR-220: Press and hold the quiet button. The
unit beeps once for VG-2 on, twice for off. The
“V” icon will illuminate when engaged.
When a VG-2 signal is detected, the VG-2 alert is
sounded. After 3 seconds, the audio is cancelled
and the VG-2 indicator flashes at a slower rate.
This cycle is repeated if the VG-2 signal is again
detected.
During the period a VG-2 signal is detected, a
radar signal cannot be detected. However,
because the VG-2 alert has confirmed that a
patrol car is nearby, you are already aware of the
potential for speed monitoring and can adjust
your speed accordingly. Laser detection is not
affected while a VG-2 signal is detected.
Option Select Mode (XTR-520 Only)
Entering Option Select Mode allows you to customize
options such as Tone Select, Abbreviated Power Up
Sequence and VG-2 Mode. Press and hold quiet
button to enter Select mode. When selecting options,
the
, or quiet must be pressed within 20 seconds
or option mode will automatically be exited. To enter:
XTR-520 Chart
Vehicle Battery Saver Mode
The Vehicle Battery Saver Mode automatically
shuts off your detector if you forget to turn it off. The
timer is reset if the detector is turned off, unplugged
or any button is pressed before the timer has
expired. The detector will alert you with an audible
and visual warning before it shuts off.
During this warning you can reset the unit by
pressing any button. This will reset the timer.
If the unit has automatically turned itself off, press the
Power button to turn the unit back on. You can
manually engage the Vehicle Battery Saver Mode by
pressing and holding the City button until one
beep is heard. (XTR-520 Only)
Refer to “Option Select Mode” for instructions for
deactivating battery saver mode feature (XTR-520
Only). XTR-220 Timer = 6 hrs, XTR-520 Timer = 3 hrs
11
Each time your Whistler detector is turned on,
an automatic self-test sequence confirms that
the speaker and visual displays are functional.
• Press Power. Display shows (XTR-520 only) in order:
1. WHISTLER 2. X-band 3. K-band 4. Ka-band
5. LASER 6. SR OFF 7. VOICE ON 8.VG-2 OFF
9. POP ON 10. B SVR ON 11. HIGHWAY
• Display indicators will light in same order for
XTR-220.
Remote Control Operation
The remote packaged with this unit transmits via
Infrared or IR, the same as most TV remote
controls. The remote’s 6 buttons can change the
unit’s features and operation. The transmit range
is approximately 4 feet.
The remote is already programmed into the
radar detector so no additional programming is
necessary. If a replacement remote is necessary
(from being lost or damaged), the new remote is
“XTR ready”
The feature buttons on the remote duplicate
those found on the laser-radar detector itself
and in case of the XTR-220 more than what the
unit can do on its own.
The remote utilizes a common coin cell battery
CR 2032 which is available at most retail outlets.
This battery should provide similar battery life as
a vehicle’s keyless entry remotes and IR
controllers
Unscrew the tip of the lighter socket
plug carefully when replacing the 2
Engaging/Disengaging VG-2
OPERATION
Power On and Self-Test
Mounting Guidelines
OPERATION
Stay Alert Feature
The Stay Alert Feature is designed to test a
driver’s alertness. To engage (when unit is not
alarming) :
• Press and hold City for approximately 2
seconds. Release button during or immediately
after the alert is given.
—XTR-520 only: Display shows:
Within 30-60 seconds two beeps are sounded;
to show alertness, the driver must press either
the City, Volume, or Quiet buttons within 3-5
seconds. If a button is pressed within 3-5
seconds, the cycle is repeated.
If a button was not pressed within 3-5 seconds
alarm sounds and the display shows:
—XTR-220 only: The “H” or “C” will flash
indicating Stay Alert is activated.
Within 30-60 seconds two beeps are sounded;
to show alertness, the driver must press either
the Volume, City or Quiet button within 3-5
seconds.
If the button is pressed within 3-5 seconds, the
cycle is repeated. If a button was not pressed within
3-5 seconds, alarm sounds and the display will
flash all LED’s.
• Press Power to exit for both models.
WARNING!!! Stay Alert is NOT intended as a
substitute for adequate rest. You should NOT operate
a vehicle if you are drowsy. During extended periods
of vehicle operation, you should take frequent
breaks. Improper reliance on the Stay Alert feature
may result in vehicle damage, personal injury or
death. NEVER OPERATE A VEHICLE IF YOU
ARE DROWSY.
12
13

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2006:03:01 08:07:14Z
Creator Tool                    : QuarkXPress(tm) 6.5
Modify Date                     : 2006:03:01 08:08:25-06:00
Metadata Date                   : 2006:03:01 08:08:25-06:00
Producer                        : QuarkXPress(tm) 6.5
X Press Private                 : %%DocumentProcessColors: Black.%%EndComments
Format                          : application/pdf
Document ID                     : uuid:da44d654-a92c-11da-8c18-0003930e16a8
Instance ID                     : uuid:da44e9ac-a92c-11da-8c18-0003930e16a8
Page Count                      : 2
Creator                         : QuarkXPress(tm) 6.5
EXIF Metadata provided by EXIF.tools
FCC ID Filing: HSXWH17

Navigation menu