Thomson 2-8108AH INTERCOM SPEAKER User Manual USERS MANUAL
Thomson Inc. INTERCOM SPEAKER USERS MANUAL
Thomson >
USERS MANUAL
Model 28108
00023528 (Rev. 0 DOM E)
08-10
Printed in China
Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
On the bottom of this equipment is a label indicating, among other information, the
US number and Ringer Equivalence Number (REN) for the equipment. You must,
upon request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number
is called. In most (but not all) areas, the sum of the RENs of all devices connected
to one line should not exceed 5. To be certain of the number of devices you may
connect to your line as determined by the REN, you should contact your local
telephone company.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. See installation instructions for details.
• This equipment may not be used on coin service provided by the telephone
company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use
your own telephone equipment if you are on a party line. Check with your local
telephone company.
• Notice must be given to the telephone company upon permanent disconnection of
your telephone from your line.
101 West 103rd Street
Indianapolis, IN 46290-1102
© 2008 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
• If your home has specially wired alarm equipment connected to the telephone
line, ensure the installation of this product does not disable your alarm equipment.
If you have questions about what will disable alarm equipment, consult your
telephone company or a qualied installer.
Should your equipment cause trouble on your line which may harm the telephone
network, the telephone company shall, where practicable, notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately. In case of such temporary discontinuance, the
telephone company must: (1) promptly notify you of such temporary discontinuance;
(2) afford you the opportunity to correct the situation; and (3) inform you of your right
to bring a complaint to the Commission pursuant to procedures set forth in Subpart
E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the operation
of its business and not inconsistent with FCC Rules and Regulations. If these changes
are expected to affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to allow you to
maintain uninterrupted service.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference; and (2) This
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or
television that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different
from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available from the U.S.
Government Printing Ofce, Washington, D.C. 20402. Please specify stock number 004-
000-00345-4 when ordering copies.
Notice: The changes or modications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensed under US Patent 6,427,009.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.
This intercom speaker is compliant with the DECT 6.0 standard
which operates in the 1.92GHz to 1.93GHz frequency range.
Installation of this equipment is subject to notication and coordination with
UTAM. Any relocation of this equipment must be coordinated through and
approved by UTAM. UTAM may be contacted at 1-800-429-8826.
Make sure your package includes the items shown here.
If one or more GE-28108’s becomes lost, you should de-register all GE-28108’s to
ensure proper system operation. Follow the steps below to de-register all
GE-28108’s at the same time.
1. Disconnect power from the telephone base by pulling the plug out of the back
of the unit.
2. Press and hold the button and while holding the page button reconnect
the power.
3. Continue to hold the button until the Charge/in use indicator ashes
rapidly.
4. Release the button.
5. Press and release the button on the telephone base once. All handsets or
the GE-28108 are de-registered and NEEDS REGISTRATION shows in the
GE-28108 display.
The system uses a menu structure to give you access to all of the built-in features.
You may program the following items in main menu: Set Language, Ring Melodies,
Ringer Volume, Key Tone, and Default setting.
1. Make sure your phone is (not in TALK mode).
2. Press the button to go to the main menu.
3. Use the ( 3or 4) button to scroll to sub-menu.
4. Press the button to enter the menu. SET LANGUAGE 1ENG 2FRA 3ESP
shows in the display. The default setting is 1ENG.
5. Use the ( 3or 4) button to scroll to the desired language.
6. Press the button to save your selection. You will hear a conrmation tone
and the selected language shows in the display.
You may choose from ten different melodies.
1. Use the ( 3or 4) button to scroll to sub-menu.
2. Press the button to enter the menu. RING MELODY 01 shows in the
display. The default setting is 01.
3. Use the ( 3or 4) button to scroll to the desired setting (01 through 10).
You will hear a sample of the ringer melody you select.
4. Press the button to save your selection. You will hear a conrmation tone
and the selected melody shows in the display.
1. Use the ( 3or 4) button to scroll to sub-menu.
2. Press the button to enter the menu. SET RINGER LEVEL 5 shows in the
display. The default setting is LEVEL 5.
3. Use the ( 3or 4) button to scroll to your selection.
4. Press the button to save your selection. You will hear a conrmation tone
and the new volume setting shows in the display.
ringer off
1. Use the ( 3or 4) button to scroll to sub-menu.
2. Press the button to enter the menu. SET KEY TONE 1ON 2 OFF shows in
the display. The default setting is 1ON.
3. Use the ( 3or 4) button to scroll to your selection.
4. Press the button to conrm and the key tone setting shows in the display.
As you become familiar with this system, you may prefer to use the system’s
original settings. Follow the steps below to return to the factory default settings.
1. Use the ( 3or 4) button to scroll to sub-menu.
2. Press the button to enter the menu. DEFAULT SETTING 1YES 2NO shows
in the display. The default setting is 2NO.
3. Use the ( 3or 4) button to or .
4. Press the button to save your selection. You will hear a conrmation tone.
1. When the phone rings, press the button on the GE-28108.
2. When nished, press the button again to hang up.
34
1. Press the button on the GE-28108 rst.
2. Dial the number on your handset or telephone base.
3. Press on the handset or telephone base to transfer the call to the
GE-28108.
4. When nished, press the button to hang up.
1. Initiate the intercom from your handset or telephone base.
2. Locate the GE-28108 from your list of registered handsets on your handset or
telephone base.
3. When the GE-28108 is being paged, it will immediately join the intercom
conversation, you can talk to the intercom party freely without pressing any
buttons.
4. When nished, press the or button on the original handset or
telephone base to end the intercom call.
1. Make sure the GE-28108 is (not in TALK mode).
2. Press the button on the GE-28108.
3. Use the ( 3or 4) button to select the handset you want to page.
4. Wait for the person at the receiving handset to press the button.
NO
ANSWER
5. When nished, press the or button on the GE-28108 to end the
intercom call.
1. During an external call, press the button on GE-28108 to conrm.
2. Use the ( 3or 4) button to scroll to the handset you want to page.
3. Press the button on GE-2108 to conrm. You will hear a paging tone
and PAGING shows in the GE-28108 display.
PAGING FROM...
4. When the receiving handset connects, press the button on the
GE-28108 to conference with the receiving handset and the external caller.
CONFERENCE shows in the display on the GE-28108 and receiving handset.
During an external call, you may transfer the external call to another handset or
GE-28108.
1. Press the button on the GE-28108 to conrm.
2. Use the ( 3or 4) button to select Handset # then press the
button on GE-2108 to conrm. You will hear a paging tone. PAGING shows on
the GE-28108’s display, and PAGING FROM... shows on the receiving handset’s
display.
3. When the receiving handset connects, press the button on the GE-28108
to transfer the call.
-OR-
4. Press the button on the GE-28108 to transfer the call. If the receiving
handset does not answer within 30 seconds, the GE-28108 rings back and
displays CALLBACK. If the GE-28108 does not answer within 20 seconds, the
call is automatically dropped.
1. Initiate room monitor from your handset or telephone base.
2. Locate the GE-28108 from the list of registered handsets on your handset or
telephone base.
3. The GE-28108 will turn on the microphone and the initiating handset or
telephone base will turn on the speakerphone to monitor sound from GE-28108.
4. If you receive an incoming call during room monitor mode, the caller ID
information will be displayed on GE-28108 and other registered handsets or
telephone base, press the button to quit room monitor mode and answer
the incoming call.
If trouble is experienced with this equipment, for warranty information, please
contact customer service at . If the equipment is causing harm to
the telephone network, the telephone company may require that you disconnect
the equipment until the problem is resolved.
Any unauthorized repairs, changes or modications not expressly approved
by Thomson Inc. could void the user’s authority to operate this product. For
instructions on how to obtain a replacement unit, refer to the warranty included in
this guide or call customer service at .
Or refer inquiries to:
Attach your sales receipt to this booklet for future reference or jot down the date
this product was purchased or received as a gift. This information will be valuable
if service should be required during the warranty period.
Purchase Date
Name of Store
1. Locate battery and battery door which are packaged together inside a plastic
bag and are separate from the GE-28108.
2. Locate the battery compartment on the back of the GE-28108.
3. Plug the battery pack cord into the jack inside the compartment.
4. Insert the battery pack.
5. Close the battery compartment by pushing
the door up until it snaps into place.
6. Plug the AC power adaptor cord into the
power jack on the back of the
GE-28108 and the other end into an
electrical outlet. The Charge/in use
indicator turns on, verifying the battery is
charging.
7. Allow the GE-28108 to charge (for
hours) prior to rst use.
After the optional GE-28108 has charged for 16 hours on the extra charger,
NEEDS
REGISTRATION
1. Press the button. HOLD BASE PAGE FOR 5 SECONDS, THEN PRESS
SPEAKER MENU shows in the display. (Your GE-28108 should be held near the
telephone base during registration process.)
2. Press and hold the button on the telephone base unit until the Charge/in
use indicator ashes. Press the GE-28108 button. REGISTERING shows in
the display. HANDSET X REGISTERED shows in the GE-28108 display, where X is
the GE-28108 number.
1. Press the ( 3or 4) button to scroll to the DEREGISTRATION
sub-menu.
2. Press the button to enter the menu. DEREGISTRATION 1YES 42NO - - -
shows in the display. The default setting is "2NO".
3. Use the ( 3or 4) button to scroll to 1YES or 2NO.
4. Select , if you do not want to de-register.
5. If you select 1YES, press the button and MOVE NEAR TO BASE displays for
2 seconds, then CONFIRM? 1YES 2NO appears in the display.
6. Use the ( 3or 4) button to scroll to 1YES or 2NO.
7. If you select , press the button to conrm. DE-REGISTER... shows in
the display. You will hear a conrmation tone. Then HANDSET X DEREGISTERED
shows in the display to conrm the GE-28108 is de-registered.
NEEDS
REGISTRATION
• Defects in materials or workmanship.
• One year, from date of purchase.
(The warranty period for rental units begins with the rst rental or 45 days
from date of shipment to the rental rm, whichever comes rst.)
• Provide you with a new unit. The exchange unit is under warranty for the
remainder of the original product’s warranty period.
• Properly pack your unit. Include any cables, etc., which were originally
provided with the product. We recommend using the original carton and
packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted invoice which is
evidence that the product is within the warranty period, must be presented to
obtain warranty service.” For rental rms, proof of rst rental is also required.
Also print your name and address and a description of the defect. Send via
standard UPS or its equivalent to:
• Insure your shipment for loss or damage. Thomson Inc. accepts no liability in
case of damage or loss.
• A new unit will be shipped to you freight prepaid.
does not
• Customer instruction. (Your Owner’s Manual provides information regarding
operating instructions and user controls. Any additional information, should
be obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modied or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
• Please complete and mail the Product Registration Card packed with your
unit. It will make it easier to contact you should it ever be necessary. The
return of the card is not required for warranty coverage.
• Some states do not allow the exclusion nor limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts
so the above limitations or exclusions may not apply to you.
• This warranty gives you specic legal rights, and you also may have other
rights that vary from state to state.
• This warranty does not apply. Contact your dealer for warranty information.
To place order, have your Visa, MasterCard, or Discover Card ready and call toll-free
.
A shipping and handling fee will be charged upon ordering.
We are required by law to collect appropriate sales tax for each individual state,
country, and locality to which the merchandise is being sent.
Items are subject to availability.