Thrane and Thrane A S RTU4120B Iridium fixed mount transceiver User Manual B4150GB0 1

Download:
Mirror Download [FCC.gov]
Document ID	548949
Application ID	PQzs+7FFjYbDnULAP5Tz7w==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	250.7kB (3133698 bits)
Date Submitted	2005-06-07 00:00:00
Date Available	2005-06-03 00:00:00
Creation Date	2005-04-14 11:24:20
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2005-04-14 15:58:19
Document Title	B4150GB0-1
Document Creator	Adobe PageMaker 7.0
Document Author:	cma

OPERATION MANUAL
SAILOR SC4000 IRIDIUM
ii
0125
Handset
What Is What?
1. Display
2. Indicator lamps
Power
Call
Network
3. Escape key
4. Call transfer key
5. Loudspeaker on/off key
6. Shift key
7. Lock on/off key
0125
Cradle
10
11
12
13
14
15
16
17
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
On/off button
Earpiece
Signal level
Opens menu
Opens phone book
Volume control/navigate menu
Hook on/off key
OK key
Loudspeaker
Microphone
iii
Introduction
Iridium Satellite System
Your Iridium equipment is a modular system that consists of a
transceiver unit, control handset unit, antenna unit and an optional
analogue PSTN telephone/PABX.
Iridium is a global satellite network for telecommunications. It
consists of 66 satellites providing world-wide coverage.
You can make and receive voice calls on the control handset and the
analogue PSTN telephone. You can connect up to four handsets
and one analogue PSTN telephone or PBX switchboard to the
system.
The system provides intercom for internal calls between any control
handsets and between the analogue telephone and a control
handset.
Via the data port on the transceiver, the unit can be used as a data
modem for dial-up data calls, Internet access, SMS and E-mail
messaging.
The Iridium system makes it possible for any two locations on Earth
to establish wireless global telephone contact.
You will need an Iridium subscription with an active Subscriber
Identification Module (SIM card). The SIM card holds your phone
number and the phone number will thus follow the SIM card if used
in another Iridium equipment.
You can buy a subscription from one of the Iridium Service Partners.
The Iridium Service Partners can be found on www.iridium.com .
Different services are available from the service partners, for
example Crew Calling, Pre and Post Paid subscriptions.
Important!
Please note
For FCC RF exposure compliance, the antenna must be
installed with a minimum distance of 0.61m (2 feet) away
from all persons.
Any responsibility or liability for loss or damage in connection with
the use of this product and the accompanying documentation is
disclaimed. The information in this manual is furnished for informational use only, is subject to change without notice, may contain
errors or inaccuracies, and represents no commitment whatsoever.
This agreement is governed by the laws of Denmark.
About this Manual
This manual provides instructions on how to operate a control
handset, an analogue telephone and on using the transceiver as a
data modem.
The instructions on operating the handset are divided into two parts.
The first part deals with Basic operation, which includes e.g. making
and answering calls. The second part describes the more advanced
functions of the system.
All functions of your Iridium equipment can be operated by following
the step by step procedures described in this manual. Each
procedure is an explicit sequence of key presses that has to be
carried out.
Doc. no.: B4150GB0
Issue: F/0512
This manual covers operation on the following transceiver unit
version:
Software
03.05.00 or higher
Hardware
mk3
Unless otherwise specified, the description of the individual
procedures has been based on the assumption that the handset is
enabled and is displaying either “Ready” or “Ready Internal” in the
display. This state is through out the manual referred to as ready
state.
We recommend that you read the manual before using the equipment.
iv
0445
Contents
Abbreviations
Handset ................................................................................ iii
CU
GPS
DTMF
LBT
PABX
PSTN
UTC
What Is What? .................................................................................... iii
Introduction ......................................................................... iv
About this Manual .............................................................. iv
Iridium Satellite System ..................................................... iv
Abbreviations ....................................................................... 1
Handset Basic Operation .................................................... 2
Handset States .................................................................................... 2
Handset Enabling/Disabling ................................................................ 2
Pin Code .............................................................................................. 2
Unlocking Handset .............................................................................. 2
Call Functions ...................................................................................... 3
Making a Manual Call .......................................................................... 4
Answering a Call ................................................................................. 5
Call Transfering ................................................................................... 5
RTU
Control unit = handset
Global Positioning System
Dual Tone Multiple Frequency
L-Band Transceiver
Public Automatic Branch Exchange (also called PBX)
Public Switched Telephone Network
Universal Time Coordinated (app. the same as Greenwich
Mean Time)
Receiver and Transmitter Unit (also called Transceiver)
Handset Advanced Operation ............................................ 7
Menu System ...................................................................................... 7
Keying in Names and Numbers .......................................................... 7
Phone Book ......................................................................................... 8
Redialling ............................................................................................. 9
Security Lock Function ...................................................................... 10
Password ........................................................................................... 11
Users ................................................................................................. 12
Call Log .............................................................................................. 13
Setting Time and Date ...................................................................... 15
Setting Dimmer and Contrast ........................................................... 15
GPS ................................................................................................... 16
Display ............................................................................................... 16
Billing ................................................................................................. 17
SIM Card Handling ............................................................................ 17
Ringing Tone ..................................................................................... 19
Extension ........................................................................................... 20
Call Answer ....................................................................................... 20
Call Forwarding ................................................................................. 21
Cancel All Forwarding ....................................................................... 21
Call Forward When Unavailable
(Busy + Not Reachable + No Reply/No Answer) ............................. 22
Call Barring ........................................................................................ 22
Call Barring of Incoming Calls .......................................................... 22
Call Barring of Outgoing Calls .......................................................... 23
Voice Mail .......................................................................................... 23
Software Version ............................................................................... 24
Resetting ........................................................................................... 24
Using an Analogue Telephone ......................................... 25
Making a Manual Call ........................................................................ 25
Analogue Phone Menu ...................................................................... 26
Billing ................................................................................................. 27
Appendix A ......................................................................... 28
Tone Signalling .................................................................................. 28
Appendix B ......................................................................... 29
Function Menu Overview .................................................................. 29
0512
Handset Basic Operation
Enter PIN
You can connect up to four handsets to this Iridium equipment.
A handset can be in one of two states: enabled or disabled.
7/9/1999
12:00:48
Handset States
In each of the two states, the handset’s normal display and signalling
can be described as follows:
Key in the pin code supplied with the SIM card. If the pin code keyed
in is correct, the handset enters ready state:
Ready
Disabled State
•
The display is cleared and the light is off.
•
The indicator lamp Power is flashing briefly every 5 seconds.
Enabled State
• In the enabled state, various information is shown on the display.
An example:
Ready
01/01/1999
23:59:59
•
7/9/1999
12:00:49
If for some reason the Iridium network is not available at the time,
the display will show “Ready Internal” and you will only be able to
make internal calls between the handsets and the analogue phone.
If you did not key in the correct pin code, you will have to try again. If
you key in a wrong pin code three times in a row, the SIM card will
be blocked and you will have to enter the PUK code to unblock it.
(The PUK code is supplied with the SIM card). See section “SIM
Card Handling” under “Handset Advanced Operation” for further
details.
The indicator lamp Power is on.
Unlocking Handset
Handset Enabling/Disabling
If the handset is locked, you have to unlock it before it can be used.
To enable/disable the handset:
Locked
1. Press and hold the on/off button.
7/9/1999
12:05:06
2. Wait until you hear the continuous tone signalling or see that the
indicator lamps Power, Call and Network are turned on simultaneously.
3. Release the on/off button.
Pin Code
Each time a valid SIM card with an enabled PIN code is inserted,
you are asked to enter your pin code:
To unlock the handset:
1. Press:
The display shows a list of user names. Your user name (I.e. the
current value of the associated priority level) determines which
facilities you have access to. Furthermore, the user name that is
used for unlocking the handset is the name stored in the call log
each time an external call is made.
>Captain
Commander
Crew
Officer
0512
1. Handset removed from hook,
but hooked on by hook key.
2. To find the right user name on the list, eg. Commander,
use:
2. Hook off.
3. No icon: Handset placed in hook, and hook on.
Volume
3. Confirm:
During a conversation, the speaker and earpiece volume can be
adjusted by means of:
Password for
Commander
4. Key in the password that corresponds to the selected user
name:
........
How to make an External Call
Entering a telephone number on a handset follows the procedure
shown with this example:
5. Confirm:
1. Hook off either by removing the handset from the hook
or by pressing the hook key
Call Functions
Speaker, Earpiece and Microphone
The earpiece is always turned on. The speaker and
microphone are always in opposite states, i.e. if the speaker is on,
the microphone is off, and vice versa.
You can toggle the speaker and microphone states by means of the
speaker key. The speaker icon appears on the display when the
speaker is on, and disappears when the microphone is on.
2. External call
3. Prefix for automatic call
00
4. Country code, e.g.
45
5. Area code, e.g.
70
Hands free operation is not possible. You can call or receive a call,
and toggle the speaker on - for listening purposes only.
Note: When the speaker is off, you can see that you are being
called (the display will show “Incoming Call”) - but there will be
no sound in the speaker.
6. Subscriber’s number, e.g. 1 3 7 0 0 0
Hooking On/Off
Before a call can be initiated, the handset must be hooked off. To do
so, either remove the handset from the hook or use the on/off-hook
key.
The handset icon on the display indicates three states, depending on
whether the handset has been hooked on or off.
0512
7. Confirmation
How to make an Internal Call
Entering a telephone number on a handset follows the procedure
shown with this example:
1. Hook off either by removing the handset from the hook
or by pressing the hook key
2. Internal number, e.g.
1001
depending on whether an internal or external call is in progress.
If the system is ready to make a call, a dialling tone is heard in the
earpiece/speaker, and the display shows:
Enter number
Type 0 for
ext. calls
or
Enter number
Internal
calls only
2. Use the numeric keys to key in the number you want to dial.
For external calls, first key: 0
3. Confirmation
To delete the previous digit, if desired, press:
Factory setup of extension numbers are:
PSTN/PABX:
Handset 1:
Handset 2:
Handset 3:
Handset 4:
An example
1000
1001
1002
1003
1004
Enter number
0 0 0 4 5 7 0 1 3 7 0 0
0_
Making a Manual Call
3. Confirm the call and start dialling by pressing:
Provided that no internal or external calls are in progress and that
the handset is enabled and unlocked, it is possible to make an
internal call.
Furthermore, if a valid SIM card has been inserted into the SIM card
slot and the correct PIN code has been entered or the PIN code has
been disabled, it is also possible to make an external call.
In order to be able to make a manual call, the handset must either be
in ready state or inside the phone book. For a description on how to
return to ready state, see section “About this Manual”. If the idle text
differs from ‘Ready’ (e.g. SIM card messages) only internal calls are
possible.
Now in order to make a manual call, do the following:
4. A calling tone is heard from the earpiece/speaker, and the
display shows:
Connecting
5. When the connection has been established, the display shows:
Connected to
0 0 0 4 5 7 0 1 3 7 0 0
0_
1. Hook off.
If the system is occupied, a busy tone is heard in the earpiece/
speaker, and the display shows either
Internal
call
External
call
or
6. When one of the calling parties end the call or if for some reason
the call is dropped, the display will show:
Call
terminated
0512
Answering a Call
NOTE: When the speaker is off you can see that you are being
called, (the display will show “Incoming Call”) but there will be
no sound in the speaker. The speaker can be toggled on and off
using:
2. Now, key in the extension number to which the call should be
transferred.
3. To transfer the call, press:
Call is
transferred
1. When the handset rings, remove it from the hook and communicate as on an ordinary telephone.
2. Adjust the volume in the earpiece or loudspeaker by means of:
- or:
To cancel transferring the call, press:
Automatic Transferring BEFORE Answering
3. When you want to stop communicating, hang up or press hook
key.
A call can be transferred to another handset automatically before it is
answered. To see if the auto transferring function is enabled,
press:
The display will show eg.:
Call Transfering
A call can be transfered to another handset. The procedure depends
on whether or not the call is answered before it is transferred.
Transferring AFTER Answering
Call transfer enabled
Local:
1001
Delay: 0 sec 10
or
Call transfer disabled
The auto transferring parameters can be set up individually for each
handset in the function menu:
When you answer a call, the display shows:
1. To enter the function menu, press:
Connected
2. To select the “Setup” item, press:
To transfer the call:
3. To find the “Transfer” item, use:
1. Press:
Enter number
and press:
0512
4. To select “Enable” or “Disable”, use :
and press:
The function has now been enabled or disabled depending on your
choice.
To select to which extension number(s) incoming calls should be
transferred, follow the steps described above. In step 4, however,
select “Extension”, after which you can key in and confirm the
wanted extension number.
To specify the time in seconds (0-60) that the call should ring before
it is transferred to the specified unit, follow the steps described
above. In step 4, however, select “Delay”. If the delay is set to 0
seconds, the call is transferred immediately; before the first handset
rings, the call is transferred to the chosen transfer destination.
0512
Handset Advanced Operation
The system features a large number of special functions. For those
of the functions that are likely to be used the most, there are special
buttons or shifted functions in connection with the numeric keys. The
functions used less often can be found in the menu system.
Menu System
The handset contains several functions for changing the system
settings, showing the status of certain system parameters, configurations, and functions for testing the system.
The menu system can always be entered from an enabled and
unlocked handset which is in ready state. See section “Handset
States” on how to return to ready state.
To confirm that you want to select an item, use the OK key:
To regret the last step, use the Escape key:
Functions marked with an asterisk (*) concern the specific handset.
All other functions are global, i.e. they concern the whole system.
The following table contains a total list of the entries in the function
menu system.
Keying in Names and Numbers
When keying in letters and numbers in the phone book, or in
connection with user names and passwords, you will need to know
To enter the function menu system, press the following key:
how many times to press each key. Pressing the key
The function menus appear:
MENU
> Setup
Call log
System
The “Setup” menu contains all functions for changing the system
parameters, such as volume, ringing tone, user names and passwords.
The “Call log” menu contains information on each call made,
including details about when the call was made, its duration, and the
receiver’s telephone number.
The “System” menu contains all functions needed for the system
administrator/super user to test and configure the system.
for instance, will give a “D”; pressing the key twice, will give an “E”,
etc.
1st push:
2nd push:
3rd push:
4th push:
5th push:
6th push:
7th push:
After each character keyed in, wait a little while to go to the next
character (the cursor appears when it is ready), or use the right
arrow key. The left arrow key deletes the last character entered.
When inside the phone book or user list;
•
to create a new entry, press:
•
to begin editing the entry selected on the list,
To navigate the menus, use the arrow keys:
press:
•
0512
once,
to delete the entry selected on the list, press:
Phone Book
The phone book offers the following facilities:
•
Up to 100 entries with names and numbers can be stored. A
telephone number may consist of up to 24 digits, and a name
may contain a maximum of 11 characters.
•
Any of the 100 stored telephone numbers can be used to initiate
a call.
•
Each entry in the phone book can be deleted.
•
New entries can be added to the phone book as long as some of
the 100 entries are free.
•
The name and/or number stored in every entry can be changed.
•
The stored entries can be searched alphabetically.
•
The current extension/local number for all connected control
units are stored in the phone book. However, only one control
unit at a time can operate in new, edit, or delete mode. If a
control unit tries to enter one of these modes, and another
control unit has done the same, the display will show: Phone
book occupied.
When you have reached the last entry, the phone book starts from
the top again with the first entry.
Alphanumeric Search
You can also search the phone book by means of the alphanumeric
keys. When inside the phone book, pressing e.g.
moves the cursor to the first entry beginning with an A. If no entry
begins with an A, or if the key is pressed twice, the cursor moves on
to the first entry beginning with a B, etc.
>Andrew
Brian
Claus
Dennis
Storing a New Entry in Phone Book
To store a new entry (name and number) in the phone book:
1. To enter the phone book, press:
Entering the phone book
The phone book can always be entered from an enabled and
unlocked handset, which is in ready state. See section “Handset
States” on how to return to ready state.
Open the phone book by pressing:
2. To enter the shifted functions, press:
3. To select the new mode, press:
4. Key in the name that corresponds to the number.
Searching the Phone Book
When entering the phone book, the display shows a list beginning
with the first entry in the phone book:
5. To store the name, press:
6. Key in the number using of the numeric keys.
7. To store the number, press:
To find previous/following entries, use:
Remember to add “0” in front of country prefix to allow external calls
An example:
Enter number
0 0 0 4 5 7 0 1 3 7 0 0
0_
0512
Changing a Number Stored in the Phone Book
Calling a Number from the Phone Book
To edit a stored number in the phone book:
To call a number stored in the phone book:
1. To enter the phone book, press:
1. To enter the phone book, press:
2. To select the desired entry in the phone book, press:
2. To select the desired entry in the phone book, press:
3. To enter the shifted functions, press:
3. To prepare for making the call:
• Lift the handset
or
4. To select the edit mode, press:
5. Key in the name that corresponds to the number.
• Press:
Now, follow the steps described in connection with “Making a manual
call”, beginning with step 3.
6. To store the name, press:
7. Key in the number using of the numeric keys.
Redialling
It is possible to redial the last number dialled by the current user. To
do so:
8. To store the new number, press:
1. Hook off.
Deleting a Stored Entry in the Phone Book
1. To enter the phone book, press:
2. Press:
3. Press:
4. To initiate the call, press:
2. To select the desired entry in the phone book, press:
A ringing tone is now heard from the handset. To go on with the call,
follow the steps described in connection with “Making a manual call”,
beginning with step 4.
3. To enter the shifted functions, press:
4. To select the delete mode, press:
5. To confirm deleting the selected entry, press:
0512
Security Lock Function
The handset can be protected against unauthorized use via the
security lock function. This works together with the list of user names
and corresponding passwords. The security lock requires that the
user selects his user name from the list, and then keys in his
personal password before the handset can be used for making calls.
The default password for all the users on the user list is “password”,
i.e. 61778562. Passwords can be edited in the Setup/Password menu
(the user’s own password) or in the /Setup/Users menu using
value of the item and the user’s priority value determine
whether the user has access to the item or not. The blocked items
are indicated by a star * in front of the item.
The user ID is written in the call log and it is thus possible to identify
who has made which calls.
Enabling Security Lock
If the security lock function has been disabled, it can be enabled by
users with a priority value of 4 or less:
1. To enter the function menu, press:
(Passwords of users with a lower priority than the current user).
The security lock function ensures that only users recognized by the
system can unlock the handset and make calls through the Iridium
system.
2. To select the “Setup” item, press:
Answering incoming calls is not protected by the security lock.
Note that from a PSTN phone (stand alone or via PABX), the
security lock is not an option.
The security lock function affects all control units. That means that if
one control unit disables the lock, the lock is disabled on all control
units connected. The same goes for enabling the lock.
User ID/User Name List
Every user specified in the system is given a priority value. The
priority value determines what the user is allowed to do in the
system. By default, the user list contains 6 entries with different
priority values. The 6 default users are shown below.
User ID/User Name
SUPER USER
Captain
Commander
Officer
Crew
Passenger
Priority value
10
100
200
3. Find the “Lock” item using:
and press:
4. To select the “Enable” item, press:
5. Find a user name of priority level 4 or less, using:
and press:
6. Enter the password using the numeric keys, and press:
The SUPERUSER has the highest priority in the system and is
therefore not restricted in any action. The SUPERUSER can edit all
other users. A user can create, edit, and delete users of a lower
priority; e.g. a user of priority value 4 may create, edit, and delete
users of priority values 10, 100, and 200.
Each item in the handset menu has a priority value. The priority
10
The handset from which the system lock was enabled, is not actually
locked before an explicit lock is issued via pressing:
0512
and confirming by
5. Find the right user name using:
This action can only be carried out if the handset is in ready state.
See section “About this Manual” on how to return to ready state.
When the lock is enabled, all other control units are automatically
locked if they are in ready state (no call in progress and not inside
the menu system or phone book). If one of these control units is not
in ready state, it is automatically locked when returning to ready
state.
Disabling Security Lock
To disable the security lock, the user has to be identified with a
priority value of 4 or less (Commander, Captain, or SUPER USER).
To disable the security lock:
1. To enter the function menu, press:
and press:
6. Key in the password, and press:
The security lock function is now disabled. This means that the
handset is ready for use for everyone without any identification of the
user. To avoid misuse of the handset, the user who disables the
security lock is asked to set the priority value. This is done by
selecting a user name from the user list and keying in the associated
password. That user name is then used as the default user of the
unlocked system. Information about subsequent outgoing calls from
any handset will be logged under this default user name.
2. To select the “Setup” item, press:
Note:
If the security lock is used for keeping track of the crew calls, each
crew member must unlock the handset before use. Do not forget to
lock the handset after use. The handsets are not locked automatically.
3. Find the “Lock” item using:
Password
A user may change his password at any time. To do so:
1. To enter the function menu, press
and press:
2. To select the “Setup” item, press
4. Find the “Disable” item using :
3. To find the “Password” item, use:
and press:
4. To confirm, press:
0512
11
Editing the Properties of an Existing User:
5. Key in the old password and confirm by pressing
6. Key in the new password and confirm by pressing
1. To enter the function menu, press:
2. To select the “Setup” item, press:
7. Re-enter the new password and confirm by pressing
3. To find the “Users” item, use
and confirm by
Users
Up to 25 users can be registered in the system by manually creating
an entry for each user. Both a user name and a temporary password
must be entered for each user.
A user may create, edit, and delete users with a priority value higher
than the user’s own priority value.
4. To find the user to be edited, use:
Adding a New User to the System:
1. To enter the function menu, press:
5. To edit the user, press:
2. To select the “Setup” item, press:
6. To go to the user property to be edited, use
3. To find the “Users” item, use
and confirm
and confirm by
by
4. To create a new user, press:
Deleting an Existing User:
5. Key in the new user name, and confirm by
1. To enter the function menu, press:
6. Key in the password, and confirm by
2. To select the “Setup” item, press:
A new user has now been added to the system with a default priority.
The priority is one of the properties that can be edited using the
procedure described next.
3. To find the “Users” item, use
12
and confirm by
0512
2. Find the item “Call Log” using
4. To find the user to be deleted, use:
and confirm by
5. To delete the user, press
3. Find the item “Private” using
and confirm by
6. Confirm by
Call Log
Information about all outgoing calls are logged. The latest 50
outgoing calls can be found in the call log. The duration of the last
outgoing call can be retrieved.
4. Find the item “Outgoing” using
and confirm by
Notice! The user name that is used for unlocking the handset is the
name stored in the call log each time an external call is made.
A list showing the phone numbers of the outgoing calls made by the
current user now appears on the display.
Viewing the Last Call
1. To enter the function menu, press:
To see more details about a specific call, find the call using
and confirm by
2. Find the item “Call Log” using
and confirm by
The total account of the current user can be retrieved by choosing
“Account” instead of “Outgoing” at step 4.
Viewing the Global Call Log
3. Find the item “Last Call” using
and confirm by
The global call log for all users in the system can be retrieved as
shown in the following:
1. To enter the function menu, press
Viewing the Last Private Call Log
The call log for the current user can be retrieved as shown in the
following:
1. To enter the function menu, press:
0512
2. Find the item “Call Log” using
and confirm by
13
Print Call Log to a Personal Computer
3. Find the item “Global” using
and confirm by
Connect a PC/Laptop to the RS232 service interface port with a
standard 9 wire serial cable. (RX on pin 2, TX on pin 3 and Ground
on pin 5)
On the PC/Laptop you can use a terminal program (e.g. hyper
terminal) to read out the call log.
Terminal port set-up: 9600 baud, 8 data bit, no parity and 1 stop bit.
A list of all outgoing calls made from the system can now be
retrieved by choosing the item “Outgoing” and pressing
In the terminal program press ESC twice and you will
see:
Thrane & Thrane a/s service interface
SI>
To see more details about a specific call, find the call using
The call log can be read out in 3 different modes.
1) Continues print mode
2) Latest calls
3) Calls made by a specific user
and confirm by
The call log record format is as follows:
Alternatively, the account of each user can be retrieved as shown
below:
An example:
A call made April 4, year 2004, time 12.01.22, by SUPERUSER to a
telephone number 00045 70101155 (labelled with HOME in the
address book) and the call duration was 1 minute and 16 seconds.
1. Follow steps 1-3 above.
2. Find the item “Account” using
[Date], [Time], [Call duration], [User name], [Subscriber name],
[Telephone number]
and confirm by
Will be read out as:
04/04-2004,12:01:22,01:16,SUPERUSER,HOME,0004570101155
A comma separates each position.
The available items are now:
Continues print mode
To read out a list of all completed calls, write “CALLS ON” on the
command line and press enter.
>Users
Phone
Unknown
Deleted Users
An example:
SI> CALLS ON [enter]
To select e.g. a specific user, choose “Users” and press
Now the call records are listed continuously until the mode is
disabled or the transceiver unit is restarted.
To disable the continuous print mode write “CALLS OFF” on the
command line and press enter.
Now, find the user by means of
14
and press
An example:
SI> CALLS OFF [enter]
0512
Latest calls
To read out a list of the latest calls, write “CALLS [number of last
calls] on the command line and press enter. Up to 50 calls can be
listed.
An example:
SI> CALLS 27 [enter]
When following this example, the last 27 calls will be read out,
starting with the latest call.
Calls made by a specific user
To read out calls made by a specified user, write CALLS [USER
NAME]
An example:
SI> CALLS SUPERUSER [enter]
This will sort out all calls made by SUPERUSER among the last 50
calls in the call log and read out each record.
Setting Time and Date
Time and date can be displayed and adjusted manually. The time is
used in the call log. Adjusting the time requires that the user is
identified with a priority value of 4 or less (Commander, Captain, or
SUPER USER).
1. To enter the function menu, press:
2. Go to the “System” item using:
and press:
You can now choose between “Status”, “Set”, “System update”,
“GPS update” and “CNT update”
Set
Sys.update
GPS.update
>CNT.update
DATE-TIME
>Status
Set
Sys.update
Status: Shows current time and date (from system).
Set: Allows you to edit time and date manually, using the numeric keys.
Sys. update: If this option is chosen, the time written in the display
is updated using an internal clock in the transceiver unit.
If power is removed from the transceiver the clock will continue
running for up to 24 hours.
GPS. update: If this option is chosen, the time written in the display
is updated using the connected GPS, if any. Consequently, even if
your Iridium system is turned off and then on again, the clock will still
be adjusted to the correct time each time a GPS update is received.
If no GPS is available, it makes no sense choosing this option.
CNT. update: If this option is chosen, the time written in the display
is updated using a software counter. Consequently,
if your Iridium system is turned off and then on again, the
clock will be reset to a default time. The correct time must then be
set again manually each time.
Setting Dimmer and Contrast
To adjust the background light and the contrast level, first press the
two keys:
and press:
The dimmer/contrast menu appears:
3. Go to “Time/date” using:
0512
DIM/CONTRAST
>Dimmer
Contrast
15
Now, move to the desired item – dimmer or contrast – by means of:
GPS
Via this menu item, it is possible to obtain the geographical position
in terms of longitude and latitude if an optional GPS receiver is
connected via the transceiver. If this is the case, the position is
available by going through the following steps:
1. To enter the function menu, press:
Then, to select the item, press:
2. To select the “Setup” item, press:
An example
When you select dimmer in the dimmer/contrast menu, the display
shows the dimmer menu:
DIMMER
>On
Off
Level
3. Find the “GPS” item using
To enable or disable the light, select the On or Off item respectively.
To adjust the dimmer level, select the Level item.
Then, to increase or decrease the dimmer level, use:
For the changes to take effect, press:
The dimmer/contrast menu may also be entered via the “Setup”
menu as follows:
For each handset, the user may select the information to be shown in
the display when the handset is in ready state. However, the state of
the system will always be shown in the display. The available
choices are:
• Time/date: Both the time (hours, minutes, seconds) and the date
is shown.
• Time: Only the time (hours and minutes) is shown.
• Position: If a GPS receiver is connected to the transceiver,
choosing “Position” will show the geographic position in terms of
latitude and longitude.
• State only: Only the state of the transceiver is shown.
If for instance you want to choose time/date;
2. To select the “Setup” item, press:
2. To select the “Setup” item, press:
16
Display
1. To enter the function menu, press:
1. To enter the function menu, press:
3. Find the “Light” item using
and press:
and press:
3. Find the “Display” item using
and press:
0512
SIM Card Handling
4. Find the “Time/date” item using
and press:
Your Iridium equipment monitors the SIM card status. The status
information is shown in the display of each handset in ready state.
SIM Card Messages
To see the effect, exit the menu system.
Billing
When a mobile originated call is initiated from the RJ11 port (PSTN/
PABX) and the call is connected to the remote user, the system
sends the billing tone to the PSTN/PABX at the RJ11 port. The tone
lasts for 500ms. Some PABX can catch this tone and start billing the
user at the PABX for the call.
Enter Billing Menu
1. To enter the function menu press:
2. Select the setup item
3. Select billing item
The following options are available in the billing menu.
As long as one of the following messages are seen in the display,
the SIM card currently inserted in the transceiver cannot be used for
making external outgoing calls.
• SIM card blocked: This message indicates that a wrong pin
code has been entered three times in a row with the current SIM
card inserted into the transceiver. To unblock the SIM card, enter the
correct PUK1 code.
• Card blocked permanently: This message indicates that a
wrong PUK1 code has been entered ten times in a row. The SIM
card is now permanently blocked and cannot be unblocked.
• SIM card defective: This message indicates that your Iridium
equipment has detected that a SIM card has been inserted into the
SIM card slot. For some reason, however, the Iridium equipment
cannot communicate with the SIM card.
• SIM card validation: This message indicates that a valid SIM
card has been inserted into the SIM card slot, and that the pin code
just entered is being validated by the Iridium system.
Note: In case of SIM card problems you must contact your Iridium
Service Partner for help.
Status
Select status will show if the billing is enabled or disabled and also
show the billing frequency.
Enabling and Disabling PIN Codes
Each SIM card has an associated PIN code. In order to prevent
unauthorized use of SIM cards, your Iridium equipment is capable of
enabling and disabling the associated PIN codes.
Enable
Select enable will enable the billing tone
Disable
Select disable will disable the billing tone
Frequency
Select frequency, select 12kHz or 16kHz, refer to PABX manual to
select correct frequency.
0512
When the PIN code from a given SIM card is enabled, the user must
enter the current value of this PIN code each time the SIM card is reentered into the SIM card holder in the transceiver. When the PIN
code for a given SIM card is disabled, the SIM card can be used for
making external outgoing calls, provided that it is not defect or
blocked.
Enabling the PIN Code
1. To enter the function menu, press:
17
Entering the PIN Code
2. Find the “System” item using:
Each time a valid SIM card with an enabled PIN code is inserted into
the SIM card holder, the current value of the associated PIN code
must be entered using the alphanumeric keys. The PIN code must be
a number consisting of 4 to 8 digits.
In order to enter the PIN code, do the following:
and press:
1. Key in the 4-8 digit PIN code and press:
Changing the PIN Code
3. Find the “SIM Card” item using:
1. To enter the function menu, press:
and press:
2. Find the “System” item using:
4. Find the “PIN enable” item using:
and press:
and press:
3. Find the “SIM Card” item using:
5. Key in the PIN code and press:
and press:
Disabling the PIN code
Follow steps 1 – 5 above with the following substitution:
4. Find the “Change PIN” item using:
Find the “PIN disable” item using:
and press:
and press:
5. Enter the current PIN code and press:
18
0512
7. Reenter the new PIN code and press:
For internal incoming calls (local calls), the resulting tones are
respectively:
• Deep dual
• High dual
• Deep dual
• High dual
Unblocking a Blocked SIM Card
As mentioned above, choosing a ringing tone affects both the
external incoming ringing tone and the internal incoming (local call)
ringing tone according to the following table:
6. Enter the new PIN code and press:
If a wrong PIN code has been entered 3 times in a row, the
transceiver blocks the SIM card. If a blocked SIM card is inserted
into the SIM card holder or if a SIM card already in the SIM card
holder is blocked, the display will show “SIM Card blocked” when the
handset is in ready state. In order to unblock a blocked SIM card:
Follow step 1 – 3 above.
Choice of ringing tone
Deep
High
Alternating slowly
Alternating fast
External incoming calls
Deep
High
Alternating slowly
Alternating fast
Internal incoming calls
Deep dual
High dual
Deep dual
High dual
An internal incoming call (local call) can always be recognized by
two equal consecutive tones (hence the term “dual” in the table)
followed by a pause. The tones may be deep or high.
4. Find the “PUK Code” item and press:
5. Enter the correct PUK code and press:
An external incoming call can always be recognized by a single
continuous sound sequence (deep, high, alternating slowly or
alternating fast), followed by a pause.
6. Enter a new 4-8 digit PIN code and press:
An example: To set the external incoming ringing tone to alternating
slowly, and the internal incoming ringing tone to deep dual (remember that they cannot be set independently as described above):
7. Re-enter the new PIN code and press:
1. To enter the function menu, press:
2. To select the “Setup” item, press:
Ringing Tone
When configuring each handset, the user can choose among a
number of different ringing tones.
The procedure is to choose one of the following 4 ringing tones:
• Deep
• High
• Alternating slowly
• Alternating fast
The ringing tone for internal incoming calls as well as the ringing
tone for external incoming calls are both affected by this single
choice. Therefore they cannot be set independently.
3. Find the “Ring tone” item using
4. Find the “Slow alt.” item using
and press:
and press:
For external incoming calls, resulting tones are respectively:
• Deep
• High
• Alternating slowly
• Alternating fast
0512
19
Extension
At any time, each handset is uniquely characterised by an extension
number. That is, only one handset at a time may have a given
extension number. The extension numbers may be changed, but no
two handsets can have the same extension number simultaneously.
To change the extension number of a handset do the following:
1. To enter the function menu, press:
2. Find the item “System” using
and press:
1. To enter the function menu, press:
2. To select the “Setup” item, press:
3. Find the item “Call Answer” using
3. Find the “Extension” item using
and press:
and press:
4. Key in a number below 10.000 that is not in use by any other
control unit, and press:
4.
Find the item “One CU” using
and press:
5. Find the extension number of the handset to which you want all
Note: The PSTN extension number cannot be changed.
external incoming calls to be directed, using
Call Answer
If your Iridium equipment includes more than one control unit or a
control unit and a PSTN telephone, you may configure the answering
of external incoming calls in a number of different ways. The
available choices are:
• One CU: Choosing this option, you must specify the extension of
the control unit to which you want external incoming calls to be
directed automatically.
and press:
Alternatively, if you want to direct external incoming calls to your
PSTN telephone (if any), follow steps 1-3 above, and proceed as
follows:
• PSTN: If there is a PSTN telephone connected to your Iridium
equipment, selecting this option will direct external incoming calls to
your PSTN telephone.
4. Find the item “PSTN” using
• All: Choosing this option will make all control units and the
PSTN telephone (if any) ring when your Iridium equipment receives
an external incoming call. Any of these units may be used for
answering the call.
An example: If you want all external incoming calls to be directed to
a control unit with the extension number 1001:
20
5. Press
and press:
again to confirm that external incoming calls
should be directed to the PSTN telephone.
0512
Call Forwarding
NOTE: This feature is a supplementary service available from
the Iridium network. Thrane & Thrane has no influence
on the availability and cannot guarantee that the service
is available. Please check the availability with your
Iridium Service Partner.
Cancel:
1. Hook off
2. Enter the following code
by pressing the keys:
#21#OK
The Iridium network offers the possibility of forwarding incoming calls
to another phone number. This facility can be configured from your
Iridium equipment. The call forwarding can be divided into the
following two categories:
• Forward all calls: All external incoming calls will immediately be
forwarded to the number you specify when you activate this
category.
• Forward on not reachable: When your Iridium equipment has
been turned off or cannot for some reason be contacted by the
network or when the line of your Iridium equipment is occupied,
either by an internal or an external call, external incoming calls will
be forwarded to the number you specify when you activate this
category.
Review forwarding number:
1. Hook off
2. Enter the following code
by pressing the keys:
*#21#OK
Note: By default, the above two categories of calls will all be
forwarded to your personal mailbox. When you activate a category,
the calls in this category will be forwarded to the number that you
specify and no longer to your personal mailbox.
In the following, the procedures for activating, restoring and reviewing settings for the above two categories are described. As usual,
when manually dialling a number to call, this must be done from
ready state.
Cancel All Forwarding
Activate:
1. Hook off
2. Enter the following code
by pressing:
#002#OK
Forwarding all Calls (Unconditional Call
Forwarding)
Activate:
1. Hook off
2. Enter the following code
*21*00 [country code]
[telephone number] # OK
by pressing the keys:
Reactivate and restore previous settings:
1. Hook off
2. Enter the following code
by pressing:
*004#OK
[country code] [telephone number]
0512
21
Call Forward When Unavailable (Busy + Not
Reachable + No Reply/No Answer)
Activate:
1. Hook off
2. Enter the following code
*004*00[country code]
[telephone number]#OK
by pressing:
Call Barring
NOTE: This feature is a supplementary service available from
the Iridium network. Thrane & Thrane has no influence
on the availability and cannot guarantee that the service
is available. Please check the availability with your
Iridium Service Partner.
Call barring allows you to bar either all external incoming or all
external outgoing calls. If you bar external incoming calls, your
Iridium equipment will not receive external incoming calls. If you bar
external outgoing calls, nobody will be able to place external
outgoing calls from your Iridium equipment.
[country code] [telephone number]
Note: External incoming calls will not be sent to your personal
mailbox if call barring of external incoming calls is active.
Before activating call barring, disable all types of call forwarding.
Call Barring of Incoming Calls
Restore forwarding to personal mailbox:
1. Hook off
2. Enter the following code
*004*00[personal mailbox
retrieval number]#OK
Activate:
1. Hook off
2. Before activating, cancel all forwarding
by pressing the keys:
#002#OK
by pressing:
[personal mailbox retrieval number]
3. Enter the following code
by pressing the keys:
Note:
*35*[password]#OK
Personal mailbox retrieval number is currently:
881631462990000
[password]
Cancel:
1. Hook off
2. Enter the following code
by pressing the keys:
22
#35*[password]#OK
0512
by pressing the keys:
[password]
Call Barring of Outgoing Calls
[old password]
Activate:
1. Hook off
2. Before activating, cancel all forwarding
by pressing the keys:
#002#OK
[new password]
[new password]
Voice Mail
3. Enter the following code
by pressing the keys:
*33*[password]#OK
Voice mail allows callers to leave a voice message in your personal
mailbox. As described in section “Call Forwarding”, by default
external incoming calls are forwarded to your personal mailbox if the
call is not answered, if your equipment is switched off, if your Iridium
system is occupied by an internal or external call or cannot, for some
reason, be contacted by the Iridium network. Therefore these calls
will be forwarded to your personal mailbox unless you set a new
telephone number to transfer to.
[password]
Cancel:
1. Hook off
2. Enter the following code
by pressing the keys:
#33*[password]#OK
To call your voice mailbox you shall call 00881662990000 associated
with your subscription i.e. SIM card number.
Changing your password:
1. Hook off
0512
You may record a personal greeting which the callers will hear when
they are forwarded to your mailbox. After hearing your personal
greeting, callers can leave a voice mail message which is stored in
your mailbox.
Your personal mailbox has a lot of features which can be configured
by you. The caller also has a number of facilities to choose between
when forwarded to your mailbox. See the “Iridium Services User
Guide” that comes together with your Iridium equipment.
[password]
2. Enter the following code
NOTE: This feature is a supplementary service available from
the Iridium network. Thrane & Thrane has no influence
on the availability and cannot guarantee that the service
is available. Please check the availability with your
Iridium Service Partner.
*03*330*[old password]*[new
password]*[new password]#OK
Your access code is for default the last 7 digits of your SIM card
number.
23
Software Version
Resetting
Primarily for service purposes, it is possible to get information about
the version of the software for the following pieces of hardware in
your Iridium equipment:
Primarily for service and test purposes, it is possible to reset your
Iridium equipment to force it into a well-defined state. The following
different levels of resetting are available:
• Transceiver: This software handles the configuration of your
Iridium equipment, audio routing, the information to be shown on the
displays, communication with your SIM card, etc.
• Restart: No configuration information or user data (call log, user
list, phone book) are deleted. When this command is issued/chosen,
all control units are forced back to ready state regardless of their
current state.
• LBT: This software handles the communication between the
global Iridium network and your Iridium equipment.
• Handset: This software consists of low level drivers (for each
control unit) that control the dot matrix display, the key pad, the
status indicator lamps, and the microphone, earpiece and speaker.
• Factory reset: NOTE! ALL (!) configuration information AND
(!) user data (call log, user list, phone book) are deleted. When this
command is issued, your Iridium equipment returns to the state it
was in when leaving the factory.
To restart your system:
To get information on these software modules, go through the
following steps:
1. To enter the function menu, press:
1. To enter the function menu, press:
2. Find the item “System” using
2. Find the item “System” using
and press:
3. Find the item “Reset” using
3. Find the item “SW version” using
4.
and press:
and press:
and press:
Choose the hardware whose software version you want informa4. Find the item “Restart” using
tion on, using
and press:
and press:
5. To confirm that you want to restart the equipment, press:
24
0512
Auto Restart
The auto restart menu is used for debugging/maintenance only.
When enabled, auto restart will only be carried through when the
system is not in use.
Under the auto restart menu, the available items are:
>Status
Enable
Disable
Timer
Enable
Disable
Timer
>Mode
Using an Analogue Telephone
You can connect an analogue telephone to your Iridium equipment.
Many of the system’s more advanced features, like the security lock
function, are however not accessible from an analogue telephone.
The accessible features are described in the Analogue Phone Menu.
Making a Manual Call
How to make an External Call
Entering a telephone number on an analogue telephone follows the
procedure shown with this example:
Mode
The mode setting is used together with the timer as a condition for
when the system can reset. The mode settings - 10 minutes, 1
minute or 0 minute - will allow the system to reset after the timer
expires and when the condition that the handset has not been in use
for a period of 10 minutes,1 minute or 0 minute has been fulfilled.
Hardware Restart
Pressing the restart switch next to the SIM card holder will power
recycle the unit.
1. Pick up phone:
dialling tone.
2. External call
3. Prefix for automatic call
00
4. Country code, e.g.
45
5. Area code, e.g.
70
6. Subscriber’s number, e.g. 1 3 7 0 0 0
7. To confirm you want to make the call,
press
How to make an Internal Call
Entering a telephone number on an analogue telephone follows the
procedure shown with this example:
1. Pick up phone:
dialling tone.
2. Internal number, e.g.
1001
3. To confirm you want to make the call,
press
0512
25
Factory setup of extension numbers are:
PSTN/PABX:
CU1:
CU 2:
CU 3:
CU 4:
Enter PUK code
If the SIM card is blocked the PUK code is needed to re-open the
card. The phone will repeat the following tone pulses:
1000Hz (300ms) – 1000Hz (300ms) – 1000Hz (300ms) – pause 1.5s
1000
1001
1002
1003
1004
Enter the PIN code press:
* 2 * PUKCODE * PINCODE #
PUKCODE
Up to four control units and a telephone/PABX can be connected to
the transceiver at the same time. Note that if connecting a PABX to
the transceiver, the PABX must function as a PSTN telephone.
To dial control unit 1 from a local telephone connected to your
Iridium equipment via a PABX, first pick up the phone, then:
PINCODE
The phone is ready when dialling tone is heard.
Enable PIN code
Pick up phone to enable PIN code.
1. Dial the number for the outgoing line connected to the transceiver, eg.
When dialling tone is heard,
press:
10
* 3 * 1 * PINCODE #
PINCODE
2. When you hear the dialling tone, dial the extension number of
control unit 1:
1001
Disable PIN code
Pick up phone to disable PIN code.
3. To confirm you want to make the call,
press
When dialling tone is heard,
press:
* 3 * 2 * PINCODE #
PINCODE
DTMF Tones - Limitations
When used for internal calls, control units do not generate DTMF
tones. Therefore the PABX cannot be set up for using DTMF tones
to access extension numbers.
Signal Level
The signal level can be retrieved by:
Pick up phone: dialling tone,
press:
Analogue Phone Menu
The phone menu is using tone notification for status indication.
When picking up the phone, tones will be pulsed if any user action is
required.
The signal level will be indicated by a beep per level with an 800Hz
tone for 50ms per beep.
1 beep indicates no signal
6 beeps indicate full level
SIM Card Handling
To return to dialling tone,
Enter PIN code
If SIM PIN code is enabled the phone will repeat the following tone
pulses:
297Hz (300ms) – 317Hz (150ms) – 237Hz (300ms) – pause 1.5s
press:
Enter the PIN code press
*4*
* 1* PINCODE #
PINCODE
The phone is ready when dialling tone is heard.
26
0512
Tone signalling on DTMF menu
Tone
Enter PIN Code
Enter PUK Code
Time
39628
Billing
When a mobile originated call is initiated from the RJ11 port (PSTN/
PABX) and the call is connected to the remote user, the system
sends the billing tone to the PSTN/PABX at the RJ11 port. The tone
lasts for 500ms. Some PABX can catch this tone and start billing the
user at the PABX for the call.
Refer to “Handset Advanced Operation” for setup instructions.
0512
27
Appendix A
Tone Signalling
The system will give you information on its status as well as
instructions by means of tone signalling. This is done on four
different frequencies: 450, 900, 1440 and 1800 Hz. Appendix A
illustrates what the various tone signalling sounds like.
1800 Hz
1440 Hz
900 Hz
450 Hz
1 sec.
RECEIVING CALLS
DEEP
HIGH
ALTERNATING
SLOWLY
ALTERNATING
FAST
TRANSMITTING CALLS
READY
BUSY
WAITING FOR
CONNECTION
NON
EXISTING
36329B
28
0512
Appendix B
Function Menu Overview
M enu
Setup
1st submenu
Ringing to ne
Ring test
Ring vo l. (*)
Speaker vo l. (*)
Key beep (*)
Lo ck
2nd submenu
Deep
High
Slo w alt.
Fast alt.
External
Internal
3nd submenu
Enable
Disable
Vo lume
Enable
Disable
P asswo rd
Users
Userlist + A dd
Userlist + Edit
Name
P asswo rd
P rio rity
Clear acco unt
Userlist + Del.
Extensio n (*)
Transfer (*)
GP S
Display (*)
Light
B illing
Call lo g
Time/date
Time
P o sitio n
State o nly
Dimmer
Co ntrast
Status
Enable
Disable
Frequence
Glo bal
Outgo ing
A cco unt
P rivate
Outgo ing
A cco unt
Last call
0512
Enable
Disable
Extensio n
Delay Time
On
Off
Level
12 kHz
16 kHz
Userlist
Users
P ho ne
Unkno wn
Del. Users
4nd submenu
A ctio n
Sets ringing to ne to deep (see A ppendix A )
Sets ringing to ne to high (see A ppendix A )
Sets the ringing to ne to alternating slo wly (see A ppendix A )
Sets the ringing to ne to alternating fast (see A ppendix A )
Generate external ringing to ne in o rder to test the setting o f this so und
Generate internal ringing to ne in o rder to test the setting o f this so und
Sets the vo lume o f the ringing to ne
Sets the speaker vo lume
Turns o n the key beep functio n: When a key is pressed, a beep is heard
Turns o ff the key beep functio n: When a key is pressed, no beep is heard
Sets the vo lume o f the beep heard when a key is pressed
Requires users to lo g in. When selecting this functio n, the user is pro mpted to
lo g in
Do es no t require users to lo g in. This functio n can o nly be selected by users
with certain prio rities. When selecting the functio n, the user is asked to state
a default user prio rity level that decides what all users will be allo wed to do .
This default prio rity level canno t be higher than that o f the user disabling the lo ck
Sets the current user’ s passwo rd
B ro wses the user list, and adds new users, entering names and passwo rds
B ro wses the user list, and edits user names
B ro wses the user list, and edits user passwo rds
B ro wses the user list, and edits user prio rities
B ro wses the user list, and clears user acco unt reco rds
B ro wses the user list, and deletes users fro m the list
Selects the extensio n number o f the current handset
Enables the auto transfer functio n
Disables the auto transfer functio n
Selects the extensio n number(s) to which calls are to be transferred
Selects the delay time befo re a call is transferred
Sho ws the current po sitio n
Displays the time and date when the handset is ready
Displays the time (ho ur and minute) when the handset is ready
Displays the po sitio n when the handset is ready
Displays o nly the state o f the system when the handset is ready
Turns the display backlight o n
Turns the display backlight o ff
A djusts the level o f the display backlight
A djusts the display co ntrast
Sho ws the status o f billing to ne
Enables the billing to ne
Disables the billing to ne
Selects the to ne frequency
B ro wses the lo g o f all o utgo ing calls
B ro wses the user list, and sho ws the acco unts o f selected users
Sho ws the acco unt o f the P STN pho ne
Sho ws the acco unts o f unkno wn users
Sho ws the acco unts o f deleted users
B ro wses the lo g o f the current user’ s calls
Views the current user’ s acco unt
View the duratio n o f the last call
29
System
Time/date
SW versio n
Call answer
SIM Card
Reset
Status
Set
Sys.update
GP S update
Transceiver
LB T
Ctrl unit
Status
One CU
P STN
A ll
P IN enable
P IN disable
Change P IN
P UK co de
Restart
Facto ry res
A uto Reset
Status
Disable
Enable
Timer
M o de
30
24 ho ur
12 ho ur
6 ho ur
1ho ur
Ready
10 min
1min
0 min
Sho ws the time and date
Sets the time and date
Sets the system to update the time and date
Sets the GP S to update the time and date
Displays the so ftware versio n number o f the transceiver
Displays the so ftware versio n number o f the LB T
Displays the so ftware versio n number o f the handset
Sho ws the status o f Call A nswer, i.e. who is set to receive inco ming calls
Inco ming calls go to a specific co ntro l unit
Inco ming calls go to the P STN pho ne
Inco ming calls go to all co ntro l units and the P STN pho ne
Enable P IN co de
Disable P IN co de
Change P IN co de
Enter P UK co de
Restarts the system (wo rks like switching the po wer o ff and o n again)
Restarts the system and relo ads all facto ry settings
Sho ws the status o f the current setting
Will disable the auto -reset functio n
Will enable the auto -reset functio n
Sets the time between auto resets
Sets the time fo r ho w lo ng the co ntro l handset must have been left unused befo re auto reset
0512
Thrane & Thrane A/S
•
info@thrane.com
•
www.thrane.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Page Count                      : 36
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:bdd234ee-e0cd-4bf4-9acd-69e466d8804e
Producer                        : Acrobat Distiller 6.0 (Windows)
Keywords                        : 
Creator Tool                    : Adobe PageMaker 7.0
Modify Date                     : 2005:04:14 15:58:19+02:00
Create Date                     : 2005:04:14 11:24:20+02:00
Metadata Date                   : 2005:04:14 15:58:19+02:00
Document ID                     : uuid:f385e3f0-e5dc-44af-8984-b11a9a1e132a
Format                          : application/pdf
Title                           : B4150GB0-1
Creator                         : cma
Description                     : B4150GB0-1
Author                          : cma
Subject                         : B4150GB0-1

EXIF Metadata provided by EXIF.tools