Thrane and Thrane A S SP3560 SAILOR SP3560 ATEX UHF Handheld Transceiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1072569
Application ID	zkWr5IFaSa9OZwOwHTZ38g==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	190.52kB (2381463 bits)
Date Submitted	2009-02-25 00:00:00
Date Available	2009-02-25 00:00:00
Creation Date	2008-11-05 12:34:58
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2009-02-16 09:35:18
Document Title	user manual
Document Creator	Adobe InDesign CS2 (4.0)

USER MANUAL
SAILOR SP3560 ATEX UHF
0845
IMPORTANT INFORMATION
Safe use of ATEX equipment:
0850
•
Do not change the battery in wet or humid environments.
•
Always keep battery connectors dry and clean.
•
Use only with Sailor ATEX approved accessories.
Alternatively ATEX approved accessories in compliance
with the accessory connector ATEX specification may be
used.
•
Do not change accessories in wet or humid enviroments.
•
Do not charge the battery in hazardous area.
•
For charge of battery use
Part no: 403505A - ATEX CH3505 Compact Charger,
Part no: 403507B - ATEX CH3507 Single Position Charger or
Part no: 403508B - ATEX CH3508 Dual Position Charger
•
Use only battery type Sailor B3503 or B3504.
•
Do not use a mechanically damaged radio.
•
Unpacking of the radio and accessories and the removal of
the protective film in front of the display window must not
take place in the ATEX protected area.
99-127722-B
SP3560 ATEX UHF
Document number: TT 98-124309-B
Release date: January, 2009
Copyright: © 2009 Thrane & Thrane A/S. All rights reserved.
Trademark Acknowledgements
• SAILOR is a registered trademark of Thrane & Thrane A/S.
• Other product and company names mentioned in this manual may be
trademarks or trade names of their respective owners.
Warranty limitation
IMPORTANT - The radio and batteries are sealed waterproof units. To create and
maintain the waterproof integrity they were assembled in a controlled
environment using special equipment. The radio and batteries are not user
maintainable units, and under no circumstances should the units be opened
except by authorized personnel. Unauthorized opening of the units will invalidate
the warranty.
Disclaimer
Any responsibility or liability for loss or damage in connection with the use of this
product and the accompanying documentation is disclaimed by Thrane & Thrane.
The information in this manual is provided for information purposes only, is
subject to change without notice and may contain errors or inaccuracies.
Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone
relying on this information should acquire the most current version e.g. from the
Thrane & Thrane Extranet at: http://extranet.thrane.com.
Thrane & Thrane is not responsible for the content or accuracy of any translations
or reproductions, in whole or in part, of this manual from any other source.
0905
Precautions
Avoid water and salt in the I/O connector and keep it
clean frequently.
Only use original Thrane & Thrane battery packs. Make
sure they are clean and dry before attaching the
transceiver. Be careful not to damage any gaskets.
Only use the original Thrane & Thrane charger for the
rechargeable battery.
Be very careful when handling the Lithium batteries.
With correct use they are safe but any misuse might
cause dangerous situations.
Never short circuit the battery terminals, never expose
the transceiver and the batteries to extreme temperature
or fire and never use any kind of violence.
Avoid close contact between the antenna and parts of
the human body. The top of the antenna must never be
closer than 2.5 cm to the body when transmitting.
Do not submerge the transceiver more than 1 m for 30
minutes.
Keep the transceiver at least 0.3 m away from the
magnetic compass.
ii
0845
Training information
SAILOR SP3560 ATEX UHF is designed for to be operated safely. It must be
operated by licensed personnel only.
The SP3560 complies with the uncontrolled RF exposure limits.
• FCC OET Bulletin 65 Supplement C, evaluating compliance with FCC guidelines
for human exposure to radio frequency electromagnetic fields.
• American National Standards Institute (C95.1) IEEE standard for safety levels
with respect to human exposure to radio frequency electromagnetic fields,
3 kHz to 300 GHz.
• American National Standards Institute (C95.3) IEEE recommended practice for
the measurement of potentially hazardous electromagnetic fields - RF and
microwaves.
Warning! Your Thrane & Thrane UHF radio generates
electromagnetic RF (radio frequency) energy when
transmitting. To ensure that you are not exposed to excessive
amounts of energy and thus to avoid health hazards from
excessive exposure to RF energy, all persons must be at least
2.5 cm away from the antenna when the radio is transmitting.
Correct use
For best performance, hold the radio vertically and 5 cm away from the head when
talking into the microphone.
Channel programming
Sailor SP3560 ATEX UHF always requires a license to operate.
For the U.S and Canadian market there are no channels pre-programmed into the
radio when leaving the factory. The users have to apply the authority for a license
and a channel allocation. The licensed channels can then only be programmed
into the radio by a general agent or the manufacture by special Service tools.
Users are not able to access or change any of the programmed channels.
0905
iii
Power settings
Power settings are adjusted at the factory. The settings for the normal "High"
power and the reduced "Low" power are saved and locked in the radio and is not
accessible for the user. The user is not able to change any of the preset power
settings. The user can only select the preset Low power or High power by pushing
a button on the keyboard.
iv
0905
Contents
Chapter 1 Introduction
Your ATEX UHF .....................................................................1
Performance ........................................................................ 2
Channels ............................................................................. 2
Chapter 2 Operation
Controls ............................................................................... 5
Keys and buttons ................................................................5
The display .........................................................................7
Using the ATEX UHF ............................................................ 8
Basic functions ...................................................................8
Other functions .................................................................. 11
Chapter 3 Batteries
Battery level indication ......................................................13
Removing and inserting the battery pack ...........................13
The battery chargers ..........................................................14
Installing the charger ........................................................14
Recharging the battery ......................................................15
Chapter 4 Configuring the radio
Configuration mode ...........................................................17
Entering and using configuration mode .............................17
List of configuration settings ............................................. 18
0845
Chapter 5 Equipment and accessories
External equipment ............................................................23
List of equipment .............................................................. 23
Connecting external equipment ........................................ 23
Impact on radio operation ................................................ 24
Accessorie connector ........................................................ 24
Accessories ....................................................................... 25
List of accessories ............................................................. 25
Attaching and removing the belt clip ................................ 27
Attaching the lanyard ....................................................... 27
Chapter 6 Troubleshooting
Displaying errors .............................................................. 29
App. A
Technical specifications
Technical data SP3560 ....................................................... 31
General .............................................................................31
Transmitter ....................................................................... 32
Receiver ........................................................................... 32
Battery life guidelines ....................................................... 34
Battery (rechargeable) ..................................................... 34
Dimensional drawing, transceiver .....................................35
Dimensional drawing, charger ...........................................36
Declaration of Conformity ..................................................38
App. B
Attention
Goretex Membran ..............................................................39
vi
0845
Chapter 1
Introduction
Your ATEX UHF
The ATEX UHF is designed for flexibility in daily
use. It connects easily to external equipment like
headsets and fist mikes, making the SP3560
suitable for any noisy environment.
Main features:
„ Unique man machine interface, an excellent
grip even with gloves, and large tactile
buttons.
„ Display with red adjustable backlight which
makes the display visible even at night.
„ Built-in “sleep” function, minimizing power
consumption and improving battery lifetime.
„ Selectable 12.5 kHz narrow band or 25 kHz
wide band operation.
„ Scrambling function for privacy calls.
„ CTCSS function for selective opening of
Squelch.
„ A lanyard and belt clip included.
A huge accessory program comes with the
SAILOR SP3500 series.
Please find the nearest SAILOR distributor on
www.thrane.com.
0845
Introduction
Performance
For best performance of the transceiver keep the following in mind:
•
Keep clear of metal environment.
•
Hold the transceiver vertically and 5 cm from lips and push the PTT
when transmitting.
•
In receive mode carry the transceiver vertically with belt clips.
•
To preserve battery power, adjust squelch to close the loudspeaker
when there is no signal.
•
If you are in a lifeboat keep the antenna as high as possible.
Channels
This radio is not programmed with any channels for USA and Canada.
The user have to apply at the authorities for a licens.
For Europe this radio can be programmed according to the following
tables:
Table 1: Single frequency simplex channels (25 kHz or 12.5 kHz use)
Channel designator
Frequency
Channel A
467.525 MHz
Channel B
467.550 MHz
Channel C
467.575 MHz
Channel D
457.525 MHz
Channel E
457.550 MHz
Channel F
457.575 MHz
0845
Introduction
Table 2: Additional channels for 12.5 kHz equipment
Channel designator
Frequency
Channel M
467.5375 MHz
Channel N
467.5625 MHz
Channel O
457.5375 MHz
Channel P
457.5625 MHz
Table 3: Two-frequency simplex channels for use with repeater only
Channel designator
Repeater RX Frequency
Repeater TX Frequency
Channel G
467.525 MHz
457.525 MHz
Channel H
467.550 MHz
457.550 MHz
Channel J
467.575 MHz
457.575 MHz
Channel K
467.5375 MHz
457.5375 MHz
Channel L
467.5625 MHz
457.5625 MHz
0845
Introduction
0845
Chapter 2
Operation
Controls
Keys and buttons
1.
On/off/volume
2. Light/Lock
3. Push To Talk (PTT)
4. Up key
5. Down key
6. Hi/Lo output power
7.
Squelch
8. Scan
9. D/P0 quick channel select
10. Loudspeaker/microphone
10
0845
Operation
Key presses
Pressing and holding certain keys gives access to additional functions,
shown in the table below.
Key
Short press
(1 beep)
Show next available
item in the list (up or
down).
Default: Channel
selection
Long press
(2 beeps)
Run through available
items, or
select tagged channels
P1 (T) or P2 (S).
Activate Squelch
control (Adjust with
up/down arrows).
Monitor function. Open
Squelch completely.
Set period of time in
configuration mode.
1 press: Activate/
terminate Dual watch.
Add/Delete channel
from memory scan.
Extra long
press
(3 beeps)
Run through
available
items if an P1
or P2 channel
is tagged
2 presses: Activate
memory scan.
Toggle between high
and low transmitter
power.
Select channel D.
Select preprogrammed
channel P0.
0845
Operation
The display
The display holds various fields of information, explained below.
10
1.
Current working channel.
2. “Lo”: Reduced transmitter power.
Full transmitter power is not shown in display.
3. Dual watch activated.
4. Current working channel is marked for scanning.
5. Keypad is locked.
6. Battery level indicator.
7.
Transmitting (TX) /Receiving (RX).
8. Accessory is connected.
9. Service line for various purposes. In this example the volume level.
10. Semi-duplex channel.
0845
Operation
Using the ATEX UHF
Basic functions
Note
Before using the radio, mount the antenna at the top of the
radio. The antenna is delivered with the radio.
Switching the radio on and off
•
To switch the radio on, turn the knob at the top
of the radio clockwise.
The display lights up showing the last used
channel and the battery level.
•
To switch the radio off, Turn the knob back
counter-clockwise until it clicks.
Selecting the working channel
•
To select channel D, press the D/P0 key.
•
To select among all available channels, press S or T on the keypad.
For fast selection, press and hold S or T.
The display shows the currently selected channel. The bottom left corner
of the display shows “Dup” if the channel is a semi-duplex channel.
Note
Long press on S or T can also be used to select preferred
channels. For information on how to program preferred
channels, see Configuring the radio on page 17.
0845
Operation
Activating a call
To activate a call to the selected channel, press and
hold the PTT button on the side of the radio.
The radio transmits as long as the PTT button is
pressed. A small TX sign next to the channel number indicates when the radio is in transmit mode.
Adjusting the volume
•
To increase the volume, turn the on/off knob at the top of the radio
clockwise.
•
To decrease the volume, turn the knob counter-clockwise.
The display shows the level of the volume, e.g. “VOL 5”, while it is
adjusted.
Using Squelch control
•
To activate Squelch control, press the SQ key.
•
To set the Squelch level, press S (closing) or T (opening). The
display shows the Squelch level while it is adjusted, e.g. “SQ 5”.
Adjusting the display backlight
•
To turn on the backlight, press the
Light/Lock button on the side of the radio.
•
To adjust the backlight level, press S or T
within 3 seconds after turning on the light.
The display shows the level while it is
adjusted, e.g. “DIM MED”.
0845
Operation
Using Dual watch (requires priority channel is programmed)
•
To activate Dual watch, press the SCN key.
The display shows “Dual” at the top and “D” at the bottom right.
The radio toggles between the selected channel and channel D (if
channel D is programmed as the priority channel).
•
To terminate Dual watch, press SCN again.
Scanning channels
•
To activate scanning memory, press 2 times SCN within ½ a second.
During scanning, the display shows “SC” in the channel field. The
radio toggles between channel D and each of the channels are
marked for scanning (only if a priority channel, e.g. D was
programmed).
•
To terminate scanning, press SCN once.
Changing the transmitter power
To change the transmitter power, press the Hi/Lo key. The display shows
“Lo” when power is set to low. Otherwise maximum power is used.
Locking the keypad
•
To lock the keypad, press and hold the Light/Lock button. The display
shows a key symbol when the keypad is locked.
•
To unlock the keypad, press and hold the Light/Lock button again.
10
0845
Operation
Other functions
Programming the scanning memory
To add a channel to the scanning memory, select the channel and then
press and hold the SCN key until the display shows MEM at the top.
To remove a channel from the scanning memory, select the channel and
then press and hold the SCN key until the MEM sign disappears from the
display.
Low power operation
The radio can be operated in low power mode. In this mode battery life
time is dramatically increased. Up to the first second of a received call
might be lost if this mode is selected. Refer to SLEEP on page 18.
Continuous Tone Coded Squelch System
Selective squelch opening by sub-tone detection (CTCSS) can be enabled,
using the configuration mode (see CTCSS on page 21). Please note that if
the radio is operating with CTCSS on a channel, and a carrier is received,
it may not be recognized in the loud speaker if the matching sub-tone is
not detected. For this reason, be very careful not to use CTCSS
programmed channels in emergency situations. For the same reason
transmitting is prohibited (reporting "BUSY") if a (silent) carrier
containing any sub-tone is active on the channel while pressing PTT.
Channels programmed with CTCSS will have a clear identification in the
service field, e.g. "CTCSS 22", while selected. Not all channels are allowed
for CTCSS use.
For maritime channels CTCSS is automatically disabled when
•
0845
Product is turned off
11
Operation
•
A new channel is selected
For private channels, the feature will remain until manually removed.
Scrambler
On channels where it is allowed, you can set up voice scrambling, using
configuration mode (see SCRM on page 22).
Please note that if the radio is operating with scrambling on a channel, it
is impossible to communicate with other radios that are not programmed
with the same scrambler code. For this reason, be very careful not to use
scrambled channels in emergency situations. Scrambled channels will
have a clear identification in the service field, e.g. "SCRM 3", while
selected. Not all regions allow the use of voice scrambling.
For maritime channels scrambling is automatically disabled when
•
Product is turned off
•
A new channel is selected
For private channels, scrambling will remain until manually removed.
Note
Prior to any initiation of scrambling, the operator must always
identify the calling station in clear voice (unscrambled) on that
channel. Use of scrambling may also be restricted by national
laws.
Narrow band operation
The radio is prepared for narrow band operation. (see BAND on page 22).
Narrow band configuration is indicated with an “n” next to the channel
designator.
12
0845
Chapter 3
Batteries
Battery level indication
When the battery level is low, you should recharge the battery.
The radio display shows the battery
status. When the battery symbol is empty
and flashing, the battery should be
recharged as soon as possible.
Removing and inserting the battery pack
To remove the battery pack, do as follows:
1.
Open the safety lock as shown.
2. Remove the battery.
To insert the battery pack, attach the battery
and then close the safety lock.
If the radio is not used for several weeks it is
recommended to store the radio and battery
separated to reduce self discharge of the
battery.
0845
13
Batteries
The battery chargers
The chargers has two compartments.
CH3505
•
A compartment for recharging the
battery alone or while attached to
the radio.
CH3507
•
A rear compartment only for
storing a spare battery. It does not
have a charger function.
•
A front compartment for
recharging the battery alone or
while attached to the radio.
CH3508
•
It is possible to charge a battery in
rear compartment simultaneously
with the radio/battery in front.
Installing the charger
Mounting the charger
There are several options for
mounting one or more chargers on a
table or a wall.
For information on dimensions and
screw positions, refer to Dimensional
drawing, charger on page 36.
14
0845
Batteries
When mounting the charger, make sure it is placed in a dry place and
away from direct sunlight. The charger is not waterproof.
Connecting to power
The charger can be supplied from DC or from AC using an AC/DC
converter.
DC: Connect the 12-24VDC Connection Cable between the DC supply and
the connector on the underside of the charger.
AC: Connect the AC/DC converter to the connector on the underside of the
charger. Then connect the AC/DC converter to the AC outlet.
Recharging the battery
To recharge the battery, place the radio with battery or the battery alone
in the front position of the charger cradle.
If the radio cannot turn on due to complete discharged battery, then turn
of the radio and place it in the charger or charge the battery alone.
The light indicators on the charger cradle show the status as follows:
•
Green light: Power is connected to the charger.
•
Slow red flash: Charging in progress.
•
Quick red flash (twice per second): Charging error, e.g. battery defect
or temperature out of range.
•
Steady red light: Charging completed. Trickle charge mode.
0845
15
Batteries
Charging time with emtpy battery: UHF off
approx. 4 hours, UHF on: approx. 5 hours.
The battery indicator on the radio display
indicates if the radio is placed in the
charger while radio and charger are both
powered.
16
0845
Chapter 4
Configuring the radio
Configuration mode
Entering and using configuration mode
Note
The radio is not operational in configuration mode.
•
To enter configuration mode, press and hold the Light/Lock button
while turning on the radio.
The bottom line of the display shows the current menu item/setting.
•
To exit configuration mode, turn off the radio or press any key except
S, T and the Light/Lock button.
Using the PTT button or leaving the radio inactive for 10 seconds also
causes the radio to exit configuration mode.
•
To change a setting, press S or T.
•
To confirm the current setting and go to the next menu item, press the
Light/Lock button.
0845
17
Configuring the radio
List of configuration settings
The following settings are available in configuration mode.
Name
LIGHT
Values
Description
MAN
Only Light/Lock button activates the backlight.
KEY
All keys and buttons, except PTT and volume
control, activate the backlight.
MAX
Status click/beep sound on key press, long
press (settings/programming saved) and
battery alarm. Maximum level.
MIN
Status click/beep sound on key press, long
press (settings/programming saved) and
battery alarm. Minimum level.
OFF
All beeps off.
VER
X.XX.XX
Software version. Read-only.
BAT
X.XX
Battery voltage (V). Read-only.
TEMP
XX.X
Temperature (°C). Read-only.
SLEEP
ON
Enable sleep mode (to minimize power
consumption).
BEEP
Sleeps for periods of 1 second after 15 seconds
of idle mode. Idle mode is: no signal detected
and no operation of the radio.
OFF
18
Disable sleep mode.
0845
Configuring the radio
Name
Values
Description
CONTRST
1, 2, 3, 4, 5 Contrast.
1 = lowest and 5 = highest.
SHANG
OFF
Off. Resumes scanning when signal
disappears.
4, 6, 8, 10
Scan hang time (in seconds) on an active
receiving working channel. The time is
measured from signal detected - remains on
channel even if signal disappears.
OFF
Automatic resume deactivated.
RESCN
Scanning/watch can be automatically resumed
3, 6, 10,
15, 20, 25, after this time (seconds) if previously
terminated with PTT.
30
SQ
WORK
TIME
A long press on SQ opens squelch. The squelch
level resumes to setting 3 seconds after SQ is
released.
MAN
A long press on SQ opens squelch. The squelch
level resumes to setting as soon SQ is
released.
ON
If the default channel D is selected using the
D/P0 key, any push on S or T will select the
working channel active before D/P0 was
pushed.
OFF
If on a distress or call channel, any push on
S or T will select the channel next to the
displayed channel.
0845
19
Configuring the radio
Name
P0
Values
Description
OFF
Remove tag “P0” for current working channel.
ON
Tag current working channel with “P0”. If
another channel was previously tagged “P0”,
this is overruled.
• The working channel can now be selected
with a long press on “D/P0”.
P1
OFF
Remove tag “P1” for current working channel.
ON
Tag current working channel with “P1”. If
another channel was previously tagged “P1”,
this is overruled.
• The working channel can now be selected
with a long press on T.
P2
OFF
Remove tag “B” for current working channel.
ON
Tag current working channel with “P2”. If
another channel was previously tagged “P2”,
this is overruled.
• The working channel can now be selected
with a long press on S.
20
0845
Configuring the radio
Name
SUBC
Values
OFF
Description
SUBC disabled. Squelch opens on all received
signals.
1, 2, ..., 38 Sub-tone carrier ID.
Squelch opens if the received signal contains
the desired subtone. During transmission the
sub-tone with the corresponding ID is
generated.
Two radios on the same channel and with the
same sub-tone ID, can reduce unwanted
incoming traffic from other users on the same
channel.
CTCSS
OFF
CTCSS disabled.
ON
Activate CTCSS on working channel. Two
radios on the same channel and with SUBC
enabled, can have a certain level of privacy.
Note that if you choose this option, the radio
immediately exits configuration mode and
starts CTCSS on the working channel.
GROUP
0845
SEL
Selective Mode. Squelch opens only if the
programmed sub-tone is received in the
signal.
ANY
Squelch opens on reception of any of the 38
sub-tones.
21
Configuring the radio
Name
SCODE
Values
Description
OFF
No scrambler code is assigned to the channel
(selecting “ON” in the SCRM setting will have
no effect).
1, 2, 3, 4,
5, CC
A selection between 5 fixed sets of scrambler
characteristics, and a custom code (CC), can be
assigned to the channel.
Note that the custom code can be defined in
the service interface.
SCRM
OFF
Scrambler disabled.
ON
Activate scrambling on working channel. Two
radios on the same channel and with
scrambling enabled, can have a certain level of
privacy.
Note that if you choose this option, the radio
immediately exits configuration mode and
starts scrambling on the working channel.
BAND
22
25.0
Wide band operation selected.
12.5
Narrow band operation selected.
0845
Chapter 5
Equipment and accessories
External equipment
List of equipment
The following equipment can be connected to the radio:
•
SAVOX 400E Push-To Talk unit
•
SAVOX C500 Fist Mike
•
SAVOX NC/400 Noise-com
•
SAVOX HC-E Helmet-com
•
SAVOX K53004 Helmet unit
•
Peltor MT7H79 Headset
We recommend to remove all accessories during emergency use.
All accessories listed might be used when body worn.
Connecting external equipment
Connect the dedicated interface cable between the external equipment
and the top connector on the radio.
Interface cable
Order number
For SAVOX 400E
403500-940
For SAVOX C500
403500-950
For Peltor FL5261
403500-952
0845
23
Equipment and accessories
When external equipment is connected
to the radio, the right side of the display
will show a headset.
Impact on radio operation
The external equipment can have a built-in PTT, speaker and
microphone. Thus connecting it to the radio will have the following
impact on the radio operation:
•
If a microphone is built into the detected external equipment, the
external equipment microphone is used, and the internal radio
microphone is disabled.
•
If a speaker or earpiece is built into the detected external equipment,
the external equipment sound device is used, and the internal radio
speaker is disabled.
•
If a PTT or VOX is built into the detected external equipment, the
external equipment PTT control is used, and the radio PTT button is
disabled.
Accessorie connector
Pin 1. Loudspeaker,
minimum 8 ohm impedance.
Pin 2. Accessory power,
3.5V maximum 13mA.
Pin 3. Microphone input,
Ri = 2.2kohm, 3V phantom power.
Pin 4. GND.
24
0905
Equipment and accessories
Accessories
List of accessories
The following accessories are delivered with your radio:
Accessory
Part number
ATEX Rechargeable battery, B3504
403504A
ATEX Compact Charger, CH3505
403505A
AC/DC converter, length 150cm (100-240V~ /12VDC out)
88-125538
12-24VDC Connection cable, length 150cm
37-124381
Belt clip
62-124320
Antenna
88-125662
Lanyard
41-124375
SP3560 User Manual (this manual)
TT 98-124309
Batteries, charger, AC/DC Converter and 12VDC Connection are described
in Batteries on page 13.
To mount the antenna, simply screw it into the threaded bush at the top
of the radio.
Use of lanyard is only for hand held operation. Put it around the wrist to
prevent dropping the radio.
0845
25
Equipment and accessories
Accessories you may buy
Accessory
Part number
ATEX Charger CH3507
403507B
ATEX Dual Position Charger CH3508
403508B
ATEX Leather Case
403500-207
Leather Case
Warning!
The display must always be kept away from the body to reduce the RF
exposure when body worn.
26
0845
Equipment and accessories
Attaching and removing the belt clip
To attach the belt clip, slide the belt clip upwards
into the rails at the back of the radio until it locks.
To remove the belt clip, press the projection at
the top of the belt clip to release the lock and
slide the belt clip downwards out of the rails.
Release lock
Attaching the lanyard
Do as follows:
Top view
1.
Take the lanyard through the
eye at the top of the radio.
2. Put one end of the lanyard
through the loop at the other
end of the lanyard and pull to
tighten.
0845
27
Equipment and accessories
28
0845
Chapter 6
Troubleshooting
Displaying errors
Some errors result in an error message in the display. These error
messages are listed below.
Display text
Problem
Type
Actions
Err
Change/recharge
Severe.
The battery voltage is
Radio is non- the battery.
below a critical level,
functional.
where further operation
would damage the battery.
Err
Hardware error.
Service required.
Severe.
Radio is nonfunctional.
Context fails operation.
This text will appear on
the following occasions:
Fail
operation
EMPTY BAT
HW ERR
ILLEGAL
Consider operation
in a different
context.
• Multiple watch is
selected on channel 16,
or in channel regions
where it is not allowed.
• High power is selected
on a channel where it is
prohibited.
• Transmission on
blocked channels
0845
29
Troubleshooting
30
0845
Appendix A
Technical specifications
Technical data SP3560
General
Item
Specification
RX frequency range
440.000 - 470.000 MHz
TX frequency range
440.000 - 470.000 MHz
Modulation
25 kHz/12.5 kHz
16K0G3E/8K50G3E
for FCC and IC: 12.5 kHz
11K0G3E
Power supply
7.2 VDC Li battery
Current drain at 2 W TX
1.0 A
Current drain at 0.4 W TX
0.7 A
Current drain RX max audio
0.25 A
Antenna port
50 ohm
Battery
Lithium-Ion, 1800 mAh rechargeable
Operating temperature
-20°C to +55°C
Water ingress protection
IP67
Frequency stability
Better than ±1.0 kHz
Weight with battery
350g
0905
31
Technical specifications
Transmitter
Item
Specification
RF output power, landmobile
1.3 W ±1.5 dB / 0.3 W ±1.5 dB
(50 ohm)
FCC: 1.3 W ±0.79 dB / 0.3 W ±0.79 dB
IC: 1.3 W ±1 dB / 0.3 W ±1 dB
RF output power, maritime
2 W radiated / 0.4 W radiated
Max deviation
25 kHz
±5 kHz
12.5 kHz
±2.5 kHz
Spurious emission
< 0.25 µW
Adjacent channel power
25 kHz
> 70 dB
12.5 kHz
> 60 dB
Receiver
Item
Specification
Sensitivity (20 dB SINAD)
-117 dBm typical
Intermodulation
Better than
EN 300 720
68 dB
EN 300 086
65 dB
Spurious response
32
> 70 dB
0905
Technical specifications
Item
Specification
Adjacent channel selectivity
25 kHz
> 70 dB
12.5 kHz
> 60 dB
Audio output, internal
0.25 W at 10% dist.
Audio output, external
0.25 W/8 ohm
0845
33
Technical specifications
Battery life guidelines
Battery (rechargeable)
Note
New batteries should be placed in the charger CH3507B or
CH3508B for minimum 12 hours first time.
During daily use, always keep the battery fully charged and away from
hot areas.
Keep the battery terminals dry and clean.
Never discharge beyond the specifications of the battery.
Operation/Standby time depends on usage. Generally, the more the radio
is transmitting, the faster it will drain the battery. Also, the “Hi” power
setting will drain the battery faster than the “Lo” setting.
Approximate figures are:
•
A battery can be stored for 4 to 6 month at 25°C if charged to 25%.
•
The battery will normally last for 5 to 9 hours of use on a fully
charged battery.
34
0845
Technical specifications
209
Dimensional drawing, transceiver
66
0845
55
35
Technical specifications
Dimensional drawing, charger
87
CH3505
Declaration of Conformity
70.4
80
Mounting Possibillities
Desktop mounting, top view
Wall mounting, rear view
46.8
30.5
40
44
22
37
36
0845
Technical specifications
CH3507 and CH3508
Mounting Possibillities
Desktop mounting, top view
0845
Wall mounting, rear view
37
Technical specifications
Declaration of Conformity
Thrane & Thrane A/S
Declaration of Conformity with R&TTE Directive
The undersigned of this letter declares that the following equipment complies with the
specifications of EC directive 1999/5/EC concerning Radio & Telecommunications Terminal
Equipment.
Equipment included in this declaration
SAILOR
SAILOR
SAILOR
SAILOR
SAILOR
SP3560
B3504
CH3505
CH3507
CH3508
ATEX Portable UHF radiotelephone
ATEX Rechargeable Li-Ion Battery
Battery Compact Charger for ATEX
Battery Charger for ATEX
Dual Battery Charger for ATEX
AC/DC Adapter
PN = 623560A
PN = 403504A
PN = 403505A
PN = 403507B
PN = 403508B
PN = 88-125538
Equipment Applicability
SAILOR SP3560 is a simplex/semi-duplex handheld UHF radiotelephone designed for maritime & landmobile communication within the frequency range 440 MHz to 470 MHz.
Declaration
The requirement with respect to the LVD directive 73/23/EC is met by conforming to the
harmonized EU standard EN 60950. The protection requirement with respect to the EMC
directive 89/336/EC is met by conforming to the harmonized EU standard EN 60945. Effective
use of frequency spectrum is met by conforming to the harmonizied EU standard ETSI
EN 300 720 and EN 300 086.
Manufacturer
Thrane & Thrane A/S
Lundtoftegårdsvej 93D, DK-2800 Kgs. Lyngby, Denmark
Porsvej 2, DK-9200 Aalborg SV, Denmark
Place and Date
Aalborg, 23. January 2009
Chief Financial Officer
Svend Åge Lundgaard Jensen
Doc. no TT99-128498-B
· Lundtoftegårdsvej 93D · DK-2800 Kgs. Lyngby · Denmark
· F +45 39 55 88 88 · info@thrane.com · www.thrane.com
· Comp. reg.: 65 72 46 18 · VAT: DK-20 64 64 46
Thrane & Thrane A/S
T +45 39 55 88 00
Bank: Danske Bank
Page 1 of 1
38
0905
Appendix B
Attention
Goretex Membran
To keep the UHF watertight, is it very important that the goretex
membran behind the label under no circumstances must be damaged or
removed.
0845
39
Attention
40
0845
TT-98-124309-B
Issue: B/0905
Thrane & Thrane A/S • info@thrane.com • www.thrane.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 52
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:efdc0a83-fc32-446b-9bcf-75e4a0ac7ed8
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2008:11:05 12:34:58+01:00
Modify Date                     : 2009:02:16 09:35:18+01:00
Metadata Date                   : 2009:02:16 09:35:18+01:00
Creator Tool                    : Adobe InDesign CS2 (4.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7299 bytes, use -b option to extract)
Instance ID                     : uuid:9479b8b2-e1b5-47e5-a02a-656bb8070b07
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:c7ea1d61-5c6b-11dc-b200-e70e930edf50
Derived From Instance ID        : c7ea1d5e-5c6b-11dc-b200-e70e930edf50
Derived From Document ID        : adobe:docid:indd:c7ea1d5d-5c6b-11dc-b200-e70e930edf50
Manifest Link Form              : ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 72.00
Manifest Placed Y Resolution    : 300.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches
Manifest Reference Document ID  : adobe:docid:photoshop:9c6d470c-5c77-11dc-a5f6-84b49ed042d1, adobe:docid:indd:fde58927-aa44-11dd-b403-d17ea70ffb3f
Manifest Reference Instance ID  : uuid:86f22677-e919-4a09-b07c-f7775f8ad5ab
Format                          : application/pdf
Creator                         : Adobe InDesign CS2 (4.0)

EXIF Metadata provided by EXIF.tools