Tonika Electronics Technology TA-320B-01 Bluetooth Speaker User Manual

Tonika Electronics Technology (Shenzhen) Co., Ltd. Bluetooth Speaker

User Manual

12 TO DC IN JACKTo Wall Outlet1512108 971114161342147116812539105 67OPERATION:8AUX IN 2 9 10GENERAL SPECIFICATIONS:Accessories:Before using the unit, be sure to read all operatinginstructions carefully. Please note that these are generalprecautions and may not pertain to your unit For example,this unit may not have the capability to be connected to anoutdoor antenna.1. Read these instructions All the safety and operating instructions should be read before the product is operated.2. Keep these instructions The sately and operating instructions should be retained for future reference.POWER SOURCEInsert the small plug from the supplied AC/DC Adaptor to DC IN Jack on the rear of unit. Insert the AC/DC Adaptor to a wall outlet having AC 100-240V~, 50/60Hz.NOTE: This AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position.1. Remote Sensor（On the front of unit）2. POWER ON/OFF Switch3. DC IN Jack (DC 12V, 2A, )4. AUX IN 2 Jacks5. AUX IN 1 Jack6. FM Antenna7. STANDBY / FM Indicator 8. Blue Tooth Indicator9. AUX 1 Indicator10. AUX 2 Indicator11. V- (Volume) Button12. V+ (Volume) Button13. (Standby) Button14. TUNE - / (Skip Backward) Button15. TUNE + / (Skip Forward) Button16. SOURCE -- LED ON/OFF Button1. (Standby) Button2. � (Mute) Button3. LED ON/OFF Button4. FM Button5. AUX 1 Button6. AUX 2 ButtonLOCATION OF CONTROL (REMOTE CONTROL)7. TUNE -/ (Skip Backward) Button8. TUNE+/ (Skip Forward) Button9. RESET Button10. � Blue Tooth Button11. VOL (Volume) - Button12. VOL (Volume) + ButtonIn first time use, slide the insulation film from the battery door and discard it as the figure on right:BATTERIES INSTALLATION(Remote Control)When the battery is consumed, replace the battery as below:1. Push the tap on the battery trap and slide it out as the figure below:2. Install a new CR 2025 button cell to the battery trap as the polarity makings on the rear of remote cabinet.3. Close the battery tray.BATTERY PRECAUTIONS:Follow these precautions when using a battery in this device:1. Use only the size and type of battery specified.2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device.3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.4. If the batteries in the device are consumed or the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s instructions.)6. Do not dispose of battery in fire. Battery may explodes or leak.7. Clean the battery contacts and also those of the device prior to battery installation.EFFECTIVE DISTANCE OF REMOTE TRANSMITTERRemarks:● When there is an obstacle between the unit and the transmitter, the transmitter may not operate.● When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the unit, the remote operation may be unstable.GENERAL:1. Slide the POWER ON/OFF Switch on the rear of unit to ON position to power on the unit. The STANDBY/FM Indicator will turn on.2. Press and hole the (Standby) Button on the unit approx 2 seconds then release the button or press the (Standby) Button on the Remote Control to turn the unit ON from standby mode. The correspondence indicator will turn on.3. Press the SOURCE Button on the unit repeatedly or correspondence buttons on the Remote Control to select the desired input source.4. Press the VOL (Volume) +/- Buttons to adjust volume level.5. Press the (MUTE) Button on the Remote Control to turn off the sound temporary, press again to turn it back.6. When finished, press and hole the (Standby) Button on the unit then release the button or press the (Standby) Button on the Remote Control to turn the unit off (standby mode). 7. If long period of time will not use the unit. Turn off the unit by slide the POWER ON/OFF Switch on the rear of unit to OFF position. All the indicators will turn off. DECORATIVE LED1. To turn on the Decorative LED, press and hold the SOURCE -- LED ON/OFF Button on the unit or press the LED ON/OFF Button on the remote control.2. To turn it off, press and hold the SOURCE -- LED ON/OFF Button on the unit or press the LED ON/OFF Button on the remote control.Radio:1. Power on the unit as previous procedures.2. Press the SOURCE -- LED ON/OFF Button on the unit repeatedly until the STANDBY/FM Indicator is light and blinking. (Or press the FM Button on the Remote Control to go to radio FM mode directly.)3. Press the TUNE+/ or TUNE -/ Button to auto search the next or pervious available FM station. 4. Repeated the same procedures until the desired FM Station is searched and play.FM Antenna:The Antenna wire on the rear of unit is for radio reception. If reception is weak, unwound and extended the wire or relocation the wire to improve the radio reception.BT (Blue Tooth):In first time use or re-pairing to new BT Device, pairing the unit to external BT Device as below: 1. Power on the unit as previous procedures.2. Press the SOURCE Button on the unit repeatedly until the BT Indicator is light and blinking.(Or press the 　　Blue Tooth Button the Remote Control to go to BT mode directly.)3. Power on the external BT Device and enter to searching mode. Start pairing as the on screen instructions on the external BT Device. After paired, the BT Indicator will stop blinking. (For details pairing procedures, please refer to the user’s manual of your BT Device.).Notes:● When the external BT Device searched the unit, our model number “CHT935BT-BLS” will appear on the display of the external BT Device.● Pairing code “0000” may need to enter. Normal operation after paired: 1. Turn on the BT function of the external BT Device. 2. Power on the unit and set the input source to BT mode as previous procedures. 3. Wait a few seconds until the unit paired to the external BT Device automatically. (The BT Indicator will stop blinking).4. Plays the music in the paired BT Device as usual.5. During playback:● Press and release the (Standby) Button on the unit to pause, press and release again to resume normal playback.● Press the /TUNE – or /TUNE + Button on the unit or Remote Control to skip tracks.AUX IN 11. Insert one of the plug from the supplied Audio connection cable (with 3.5mm stereo mini plugs) to the Phones Jack; Line Out Jack or AUX Out Jack on external audio device such like iPhones; iPad; iPod; MP3 Player; Discman … etc. Insert the other end to the AUX IN 1 Jack on the rear of the unit as the figure below.2. Power on the unit as previously procedures.3. Press the SOURCE -- LED ON/OFF Button on the unit repeatedly until the AUX 1 Indicator is light. (Or press the AUX 1 Button on the Remote Control to go to AUX 1 mode directly.)4. Plays the music on the connected external Audio device as usual. (Make sure the volume level of the external device is in high level. Otherwise, sound from this unit is weak).1. Insert one end of RCA connection cable ( Not supplied ) to the Audio Out Jacks (RCA Type) on external Video/Audio device such like TV; DVD Player; VCR … etc. Insert the other end to the AUX in 2 Jacks on the rear of the unit as the figure below.2. Power on the unit as previously procedures.3. Press the SOURCE -- LED ON/OFF Button on the unit repeatedly until the AUX 2 Indicator is light. (Or press the AUX 2 Button on the Remote Control to go to AUX 2 mode directly.)4. Plays the music on the connected external Audio device as usual. (Make sure the volume level of the external device is in high level. Otherwise, sound from this unit is weak).TROUBLESHOOTING GUIDECheck the follows before requesting service: Power Source: ………………………………DC 12V, 2A, Centre PositivePower Source of Remote Control: ….DC 3V, 1 x CR 2025 Button Cell (Included) Power Consumption: ………………………………………………………….. Max. 24 WRadio FM Band Coverage: …………………………………………….…. 87.5-108MHzBT Effective Range: ...................................…………......... Up to 32 Feet in open areaRemote Control Effective Range ……………………………Up to 12 Feet in open area Audio Power: ………………………………………………………………..….20W (RMS)Impedance of Speakers: ……………………………………………….. 4 Ohm; 6 W x 4 1 x User’s Manual1 x Remote Control (Use 1 x CR 2025 button cell, already installed) 1 x Audio Connection Cable with 3.5mm Stereo Mini Plugs1 x AC/DC Adaptor (Input: AC 100-240V~, 50/60Hz 1A; Output: DC 12V, 2A , Centre Positive）2613 4 5SYMPTOM POSSIBLE CAUSE No power AC/DC Adaptor had notplug in wall outletPlug it to the wall outletproperlySmall plug from the suppliedAC/DC Adaptor had notconnected to the unitInsert the small plug fromthe supplied AC/DC Adaptorto the DC in Jack on therear of unitPOWER Switch is in OFFpositionSlide the POWER Switch onthe rear of unit to ONpositionThe unit in standby mode Press and hold the(Standby) Button on the unitapprox. 2 seconds thenrelease the button or Pressthe (Standby) Button onthe Remote Control to turnon the unit from standbymode.No Sound Volume in minimum position Rise volume level by presstheThe connected device is notin playback modePlays the music/movie inthe connected device as usualSound output of theconnected device weakRise the volume level of theconnected deviceInput source incorrectconnectionSound distortion Volume level too highpress theVolume level of theconnected device too high the connected deviceBT not functioning The external BT device toofar from the unitPlace the external BTdevice close to the unitRemote not functioning The batteries in the remotecontrol consumedReplace by new batteriesSet the input source as theReduce the volume level byPOSSIBLE SOULTIONVOL (Volume) + ButtonVOL (Volume) - ButtonReduce the volume and/or bass level ofCraig warrants this product to be free from manufacturing defects in material andworkmanship under normal use for a period of 90 days from date of purchase. If serviceis required, please return the product to the store where it was purchased for exchange;or, pack the unit in the original packing material with all accessories if applicable, a copyof your sales receipt and a Cashier’s check or Money Order for $18.00 (to cover shippingand handling costs) payable to Craig Electronics Inc. For consumers in Canada, pleasemake sure that the cashier check or money order is redeemable through a U.S. bank.Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit cannot be repaired or replaced, a refund will be forwarded to you within four weeks of receiptof your unit. Please ship your unit to:Craig Electronics Inc.1160 NW 163 DriveMiami, Fl 33169This warranty is void if the product has been: a) Used in a commercial application or rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by anyone other than an authorized Craig service center. d) Damaged because it is improperly connected to any other equipment.Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s Manual which can be performed by the customer. b) Damage to equipment not properly connected to the product. c) Any cost incurred in shipping the product for repair. d) Damage to the product not used in the USA.This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter.Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state. Some states do not allow limitations on implied warranties or exclusion of consequential damage. Therefore, these restrictions may not apply to you.To Obtain Service on your Productemail:service@craigelectronics.comPrinted in China CHT935BT-BLS_WC_E0FG1_V0USLIMITED WARRANTYModel: CHT935BT-BLSFCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 　 Reorient or relocate the receiving antenna. 　 Increase the separation between the equipment and receiver. 　 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 　 Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Navigation menu