Tonika Electronics Technology TA-320B-01 Bluetooth Speaker User Manual
Tonika Electronics Technology (Shenzhen) Co., Ltd. Bluetooth Speaker
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2741023 |
| Application ID | FyvU9D/mtLB+ho3uXRHC9w== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 390.79kB (4884815 bits) |
| Date Submitted | 2015-09-09 00:00:00 |
| Date Available | 2015-09-09 00:00:00 |
| Creation Date | 0000-00-00 00:00:00 |
| Producing Software | Adobe PDF library 9.90 |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | TA-320 说明书三ç§è¯è¨€åˆæˆä¸€æœ¬ï¼ˆ2013-7-27） |
| Document Creator | Adobe Illustrator CS5 |
| Document Author: | Administrator |
LOCATION OF CONTROL (REMOTE CONTROL) POWER SOURCE Insert the small plug from the supplied AC/DC Adaptor to DC IN Jack on the rear of unit. Insert the AC/DC Adaptor to a wall outlet having AC 100-240V~, 50/60Hz. NOTE: This AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position. BATTERIES INSTALLATION(Remote Control) In first time use, slide the insulation film from the battery door and discard it as the figure on right: TO DC IN JACK To Wall Outlet When the battery is consumed, replace the battery as below: 1. Push the tap on the battery trap and slide it out as the figure below: 2. Install a new CR 2025 button cell to the battery trap as the polarity makings on the rear of remote cabinet. 3. Close the battery tray. 12 11 1. Remote Sensor（On the front of unit） 2. POWER ON/OFF Switch 3. DC IN Jack (DC 12V, 2A, 4. AUX IN 2 Jacks 5. AUX IN 1 Jack 6. FM Antenna 7. STANDBY / FM Indicator 8. Blue Tooth Indicator 9. AUX 1 Indicator 16 10. AUX 2 Indicator 13 11. V- (Volume) Button 12. V+ (Volume) Button 11 13. (Standby) Button 14. TUNE - / (Skip Backward) Button 15. TUNE + / (Skip Forward) Button 16. SOURCE -- LED ON/OFF Button Before using the unit, be sure to read all operating instructions carefully. Please note that these are general precautions and may not pertain to your unit For example, this unit may not have the capability to be connected to an outdoor antenna. 1. Read these instructions All the safety and operating instructions should be read before the product is operated. 2. Keep these instructions The sately and operating instructions should be retained for future reference. Model: CHT935BT-BLS 10 EFFECTIVE DISTANCE OF REMOTE TRANSMITTER 8 9 10 14 15 12 BATTERY PRECAUTIONS: Follow these precautions when using a battery in this device: 1. Use only the size and type of battery specified. 2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. 4. If the batteries in the device are consumed or the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s instructions.) 6. Do not dispose of battery in fire. Battery may explodes or leak. 7. Clean the battery contacts and also those of the device prior to battery installation. 1. 2. 3. 4. 5. 6. 7. TUNE -/ (Skip Backward) Button 8. TUNE+/ (Skip Forward) Button 9. RESET Button 10. � Blue Tooth Button 11. VOL (Volume) - Button 12. VOL (Volume) + Button (Standby) Button � (Mute) Button LED ON/OFF Button FM Button AUX 1 Button AUX 2 Button Remarks: ● When there is an obstacle between the unit and the transmitter, the transmitter may not operate. ● When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the unit, the remote operation may be unstable. OPERATION: GENERAL: 1. Slide the POWER ON/OFF Switch on the rear of unit to ON position to power on the unit. The STANDBY/FM Indicator will turn on. 2. Press and hole the (Standby) Button on the unit approx 2 seconds then release the button or press the (Standby) Button on the Remote Control to turn the unit ON from standby mode. The correspondence indicator will turn on. 3. Press the SOURCE Button on the unit repeatedly or correspondence buttons on the Remote Control to select the desired input source. 4. Press the VOL (Volume) +/- Buttons to adjust volume level. 5. Press the (MUTE) Button on the Remote Control to turn off the sound temporary, press again to turn it back. 6. When finished, press and hole the (Standby) Button on the unit then release the button or press the (Standby) Button on the Remote Control to turn the unit off (standby mode). 7. If long period of time will not use the unit. Turn off the unit by slide the POWER ON/OFF Switch on the rear of unit to OFF position. All the indicators will turn off. AUX IN 1 1. Insert one of the plug from the supplied Audio connection cable (with 3.5mm stereo mini plugs) to the Phones Jack; Line Out Jack or AUX Out Jack on external audio device such like iPhones; iPad; iPod; MP3 Player; Discman … etc. Insert the other end to the AUX IN 1 Jack on the rear of the unit as the figure below. 2. Power on the unit as previously procedures. 3. Press the SOURCE -- LED ON/OFF Button on the unit repeatedly until the AUX 1 Indicator is light. (Or press the AUX 1 Button on the Remote Control to go to AUX 1 mode directly.) 4. Plays the music on the connected external Audio device as usual. (Make sure the volume level of the external device is in high level. Otherwise, sound from this unit is weak). TROUBLESHOOTING GUIDE Check the follows before requesting service: SYMPTOM POSSIBLE CAUSE POSSIBLE SOULTION No power AC/DC Adaptor had not plug in wall outlet Plug it to the wall outlet properly Small plug from the supplied Insert the small plug from AC/DC Adaptor had not connected to the unit the supplied AC/DC Adaptor to the DC in Jack on the FM Antenna: The Antenna wire on the rear of unit is for radio reception. If reception is weak, unwound and extended the wire or relocation the wire to improve the radio reception. BT (Blue Tooth): In first time use or re-pairing to new BT Device, pairing the unit to external BT Device as below: 1. Power on the unit as previous procedures. 2. Press the SOURCE Button on the unit repeatedly until the BT Indicator is light and blinking.(Or press the Blue Tooth Button the Remote Control to go to BT mode directly.) 3. Power on the external BT Device and enter to searching mode. Start pairing as the on screen instructions on the external BT Device. After paired, the BT Indicator will stop blinking. (For details pairing procedures, please refer to the user’s manual of your BT Device.). Notes: ● When the external BT Device searched the unit, our model number “CHT935BT-BLS” will appear on the display of the external BT Device. ● Pairing code “0000” may need to enter. AUX IN 2 1. Insert one end of RCA connection cable ( Not supplied ) to the Audio Out Jacks (RCA Type) on external Video/Audio device such like TV; DVD Player; VCR … etc. Insert the other end to the AUX in 2 Jacks on the rear of the unit as the figure below. 2. Power on the unit as previously procedures. 3. Press the SOURCE -- LED ON/OFF Button on the unit repeatedly until the AUX 2 Indicator is light. (Or press the AUX 2 Button on the Remote Control to go to AUX 2 mode directly.) 4. Plays the music on the connected external Audio device as usual. (Make sure the volume level of the external device is in high level. Otherwise, sound from this unit is weak). POWER Switch is in OFF position Slide the POWER Switch on the rear of unit to ON position The unit in standby mode Press and hold the (Standby) Button on the unit approx. 2 seconds then release the button or Press the (Standby) Button on the Remote Control to turn on the unit from standby mode. No Sound Sound distortion BT not functioning Normal operation after paired: 1. Turn on the BT function of the external BT Device. 2. Power on the unit and set the input source to BT mode as previous procedures. 3. Wait a few seconds until the unit paired to the external BT Device automatically. (The BT Indicator will stop blinking). 4. Plays the music in the paired BT Device as usual. 5. During playback: ● Press and release the (Standby) Button on the unit to pause, press and release again to resume normal playback. ● Press the /TUNE – or /TUNE + Button on the unit or Remote Control to skip tracks. LIMITED WARRANTY Power Source: ………………………………DC 12V, 2A, Centre Positive Power Source of Remote Control: ….DC 3V, 1 x CR 2025 Button Cell (Included) Power Consumption: ………………………………………………………….. Max. 24 W Radio FM Band Coverage: …………………………………………….…. 87.5-108MHz BT Effective Range: ...................................…………......... Up to 32 Feet in open area Remote Control Effective Range ……………………………Up to 12 Feet in open area Audio Power: ………………………………………………………………..….20W (RMS) Impedance of Speakers: ……………………………………………….. 4 Ohm; 6 W x 4 rear of unit DECORATIVE LED 1. To turn on the Decorative LED, press and hold the SOURCE -- LED ON/OFF Button on the unit or press the LED ON/OFF Button on the remote control. 2. To turn it off, press and hold the SOURCE -- LED ON/OFF Button on the unit or press the LED ON/OFF Button on the remote control. Radio: 1. Power on the unit as previous procedures. 2. Press the SOURCE -- LED ON/OFF Button on the unit repeatedly until the STANDBY/FM Indicator is light and blinking. (Or press the FM Button on the Remote Control to go to radio FM mode directly.) 3. Press the TUNE+/ or TUNE -/ Button to auto search the next or pervious available FM station. 4. Repeated the same procedures until the desired FM Station is searched and play. GENERAL SPECIFICATIONS: Remote not functioning Volume in minimum position Rise volume level by press the VOL (Volume) + Button The connected device is not in playback mode Plays the music/movie in the connected device as usual Sound output of the connected device weak Rise the volume level of the connected device Input source incorrect Set the input source as the connection Volume level too high Reduce the volume level by press the VOL (Volume) - Button Volume level of the connected device too high Reduce the volume and/or bass level of the connected device The external BT device too Place the external BT far from the unit device close to the unit The batteries in the remote Replace by new batteries FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Craig Electronics Inc. 1160 NW 163 Drive Miami, Fl 33169 Accessories: 1 x User’s Manual 1 x Remote Control (Use 1 x CR 2025 button cell, already installed) 1 x Audio Connection Cable with 3.5mm Stereo Mini Plugs 1 x AC/DC Adaptor (Input: AC 100-240V~, 50/60Hz 1A; Output: DC 12V, 2A , Centre Positive） NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable This warranty is void if the product has been: a) Used in a commercial application or rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by anyone other than an authorized Craig service center. d) Damaged because it is improperly connected to any other equipment. Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s Manual which can be performed by the customer. b) Damage to equipment not properly connected to the product. c) Any cost incurred in shipping the product for repair. d) Damage to the product not used in the USA. This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter. Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state. Some states do not allow limitations on implied warranties or exclusion of consequential damage. Therefore, these restrictions may not apply to you. To Obtain Service on your Product email:service@craigelectronics.com protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm Printed in China control consumed Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange; or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money Order for $18.00 (to cover shipping and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please make sure that the cashier check or money order is redeemable through a U.S. bank. Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt of your unit. Please ship your unit to: 10 CHT935BT-BLS_WC_E0FG1_V0US between the radiator & your body
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : Administrator Create Date : 0000:01:01 00:00:00 Modify Date : 0000:01:01 00:00:00 XMP Toolkit : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00 Creation Date--Text : Producer : Adobe PDF library 9.90 Mod Date--Text : Format : application/pdf Creator : Administrator Title : TA-320 说明书三种语言合成一本（2013-7-27） Creator Tool : Adobe Illustrator CS5 Metadata Date : 2015:08:19 16:37:20+08:00 Thumbnail Width : 256 Thumbnail Height : 28 Thumbnail Format : JPEG Thumbnail Image : (Binary data 4671 bytes, use -b option to extract) Document ID : xmp.did:AF02069251F6E2118E7CE2B78F816B38 Instance ID : uuid:dc2e8061-f7f5-412d-9181-f044fe28303e Rendition Class : proof:pdf Original Document ID : uuid:cb39e346-47d6-479b-b32d-df1ba4edad9c Derived From Instance ID : uuid:18644943-05a6-4e80-8554-0a5e6973d09c Derived From Document ID : xmp.did:851BE9142CE8E211BD1EA7399068977F Derived From Original Document ID: uuid:cb39e346-47d6-479b-b32d-df1ba4edad9c Derived From Rendition Class : proof:pdf History Action : saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:5B2EA942E2B5E211B256CEE51BA50F41, xmp.iid:71DFE2FABEB6E21185B6DF76922F5637, xmp.iid:72DFE2FABEB6E21185B6DF76922F5637, xmp.iid:25686EB2EAB6E21185B6DF76922F5637, xmp.iid:26686EB2EAB6E21185B6DF76922F5637, xmp.iid:7319526053D5E211AB8F84E3E18FE501, xmp.iid:851BE9142CE8E211BD1EA7399068977F, xmp.iid:AF02069251F6E2118E7CE2B78F816B38 History When : 2013:05:06 08:16:56+08:00, 2013:05:07 10:36:54+08:00, 2013:05:07 10:37:10+08:00, 2013:05:07 20:53:44+08:00, 2013:05:07 20:55:32+08:00, 2013:06:15 08:34:44+08:00, 2013:07:09 08:11:20+08:00, 2013:07:27 08:31:34+08:00 History Software Agent : Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5 History Changed : /, /, /, /, /, /, /, / N Pages : 1 Has Visible Transparency : False Has Visible Overprint : True Max Page Size W : 1983.996901 Max Page Size H : 281.516667 Max Page Size Unit : Millimeters Font Name : Arial-BoldMT, ArialMT, CTHeiTiSJ, AdobeSongStd-Light, SimSun, MicrosoftYaHei, Helvetica_cyr-Bold Font Family : Arial MT, Arial, 创艺简黑体, Adobe 宋体 Std, 宋体, 微软雅黑, Helvetica Font Face : Bold, Regular, Regular, L, Regular, Regular Font Type : Open Type, Open Type, TrueType, Open Type, TrueType, Open Type, Unknown Font Version : 001.001, Version 3.00, Version 5.002;PS 5.002;hotconv 1.0.49;makeotf.lib2.0.15106, Version 3.12, Version 5.00, 1.0 Tue Mar 09 12:38:27 1993 Font Composite : False, False, False, False, False, False, False Font File Name : Arial-BoldMT.otf, ARIAL.TTF, 创艺简黑体.TTF, AdobeSongStd-Light.otf, simsun.ttc, MSYH.TTF, Helvetica Bold.Ttf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Swatch Groups Colorants Swatch Name: AutoCAD Color Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Cyan : 92.971700 Swatch Groups Colorants Magenta : 87.972802 Swatch Groups Colorants Yellow : 89.019603 Swatch Groups Colorants Black : 79.998499 Page Count : 1 For : Administrator, Bounding Box : 129 136 5586 733 Container Version : 11 Creator Version : 15 Image Height : 597 Image Width : 5457 Image Size : 5457x597 Megapixels : 3.3EXIF Metadata provided by EXIF.tools