Toplink Technology Development TOP-MS04 Wireless module User Manual
Shenzhen Toplink Technology Development CO.,LTD Wireless module
user manual
Shenzhen Toplink Technology.,Ltd User Manual Product Name: Wireless module Model Number: TOP-MS04 1/6 | ADD:2F,BldgB,JindingshengIndustrial Park, DaHe Road, Longhua,Shenzhen Call:0755-85225016/89345781 Fax:0755-28471983 Shenzhen Toplink Technology.,Ltd 1.Introduction TOP-MS04 is a WLAN module supporting IEEE 802.11b/g/n standards with 4-pin connector supporting USB2.0 interface. This is a low cost compact WLAN module designed in the product with embedded system for the wireless connectivity. Scope: TOP-MS04 WLAN module is designed to operate in 2.4GHz ISM frequency band it applies a highly integrated MAC/BBP and RF single chip RT5070 with 150Mbps PHY rate supporting it fully complies with 802.11b/g/n draft 3.0 and 802.11b/g/n feature 802.11b:1,2,5.5,11Mbps; 802.11g:6,9,12,18,24,36,48,54Mbps 802.11n:(20MHz)MCS0-7,Support 40MHz) OFDM,Peak rate Security support Operates in Antenna 150Mbps,Peak for 2.4GHz On 2.Product to 72Mbps MCS0-7,Support up to 150Mbp throughput 90Mbps. 64/128 WEP,WPA,WPA2,TKIP,AES frequency configuration:I-PEX Built-in up bands. Power receptacle for Management external antenna/ Board Information Standards Operating Frequency IEEE802.11b/g&802.11n(1T1R Protocols 802.11b: CCK, Antenna External Antenna Security WPA/WP2,64/128/152-bit mode) USA(FCC):2.412GHz~2.462GHz(channel Europe 1–11)ISM (CE):2.412GHz~2.472GHz(channel QPSK, BPSK, via an WEP, band 1–13)ISM band 802.11g/n:OFDM I-PEX receptacle/Built-in WPS 2/6 | ADD:2F,BldgB,JindingshengIndustrial Park, DaHe Road, Longhua,Shenzhen Call:0755-85225016/89345781 Fax:0755-28471983 On Board Shenzhen Toplink Technology.,Ltd ReceiveSensitivity 11b:-86dBm@11Mbps;11g:-72dBm@54Mpbs. 802.11n:(HT20),-68dBm@MSC7,(HT40),-64dBm@MSC7 Operating Voltage 5.0VDC±5%(or3.3VDV±5%upon Operating Current <110mA Bus Interface USB USB Interface USB2.0 Antenna at 5.0V DC special requirement) input. 2.0/USB1.1 Impedance I-PEX receptacle for external antenna/Built-in onBoard Specification Overview Operation System CPU Supplier Driver Linux 2.4/2.6 ARM, MIPSII Available Windows 2000/XP/Vista X86 Platform Available Windows CE 5.0/6.0 ARM, MIPSII Available Mac OS X 10.3/10.4/10.5/10.6 N/A Available Software and syste Information 3.Temperature Operating Temperature Continuous reliable operation in Storage ambient temperature:-20ºC to+45ºC Temperature The product is not damaged or degraded when keeping in -20ºC to +85ºC 3/6 | ADD:2F,BldgB,JindingshengIndustrial Park, DaHe Road, Longhua,Shenzhen Call:0755-85225016/89345781 Fax:0755-28471983 Shenzhen Toplink Technology.,Ltd 4.Humidity Operating Humidity Conditions The product is capable of continuous reliable operation when subjected to relative humidity in the range of 20% to 80% (non-condensing) Non-Operating Humidity Conditions (including warehouse) The product is not damaged or degraded when kept in the relative humidity range from 20% to 80% 5.Disclaimer These MaterIals And Information Are Provided“AS IS” Without.Warranty of Any Ki nd, Either Express or Implied, Including But Not. Limited To, The Implled Warranties Of Merchantability, Fitness For A. particular Purpose or Non-infringement. We uses reasonable efforts to include accurate and up-to-date information on th is document.it does not, however, make any representations as to its accuracy or co mpleteness of the.information, text, graphics, links or other items contained within these materials. Your use ofthis Document is at your own risk. TOPLINK, its suppliers , and other parties involved in.creating and delivering this Document’s contents shall not be liable for any special, indirect,incidental, or consequential damages, includin g without limitation, lost revenues or lost profits. 4/6 | ADD:2F,BldgB,JindingshengIndustrial Park, DaHe Road, Longhua,Shenzhen Call:0755-85225016/89345781 Fax:0755-28471983 Shenzhen Toplink Technology.,Ltd FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two condi tions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could v oid the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital de vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec tion against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructio ns, may cause harmful interference to radio communications. However, there is no guarantee tha t interference will not occur in a particular installation. If this equipment does cause harmful inter ference to radio or television reception, which can be determined by turning the equipment off a nd on, the user is encouraged to try to correct the interference by one or more of the following m easures: ‐ Reorient or relocate the receiving antenna. ‐ Reorient or relocate the receiving antenna. ‐ Reorient or relocate the receiving antenna. ‐Consult the dealer or an experienced radio/TV technician for help important announcement Important Note: Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions: 1. The transmitter module may not be co-located with any other transmitter or antenna, As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Important Note: In the event that these conditions cannot be met (for example co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following" Contains FCC ID: 2AATNTOP-MS04 ". 5/6 | ADD:2F,BldgB,JindingshengIndustrial Park, DaHe Road, Longhua,Shenzhen Call:0755-85225016/89345781 Fax:0755-28471983 Shenzhen Toplink Technology.,Ltd Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 6/6 | ADD:2F,BldgB,JindingshengIndustrial Park, DaHe Road, Longhua,Shenzhen Call:0755-85225016/89345781 Fax:0755-28471983
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2016:06:21 18:03:13+08:00 Create Date : 2016:06:21 18:03:13+08:00 Format : application/pdf Title : Microsoft Word - User Manual Creator : Administrator Document ID : uuid:63589306-47d0-444d-9ced-3c80a388de3b Instance ID : uuid:a5e61927-ae2d-41dc-9e1e-98016bc981a9 Page Count : 6 Author : AdministratorEXIF Metadata provided by EXIF.tools