Toro 5010 H Rm5010h 0 User Manual To The 86212508 B1f8 4e00 8800 Fde94b2fc51b
User Manual: Toro 5010-H to the manual
Open the PDF directly: View PDF
Page Count: 335 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- Preface
- Table Of Contents
- Table Of Contents (Continued)
- 1 - Safety
- 2 - Product Records and Maintenance
- 3 - Kubota Diesel Engine
- Kubota Workshop Manual, 05-E4B Series
- 4 - Hydraulic System
- Table of Contents
- Specifications
- General Information
- Hydraulic Schematic
- Hydraulic Flow Diagrams
- Special Tools
- Troubleshooting
- Testing
- Traction Circuit Relief Valve (R3) and (R4) Pressure Test
- Traction Circuit Charge Pressure Test
- Gear Pump (P2) Flow Test
- Front Wheel Motor Efficiency Test
- Piston (Traction) Pump Flow Test
- Lift Relief Valve (SVRV) Pressure Test
- Gear Pump (P1) Flow Test
- Lift Cylinder Internal Leakage Test
- Steering Relief Valve (R10) Pressure Test
- Steering Cylinder Internal Leakage Test
- Service and Repairs
- General Precautions for Removing and Installing Hydraulic System Components
- Check Hydraulic Lines and Hoses
- Flush Hydraulic System
- Filtering Closed- Loop Traction Circuit
- Hydraulic System Start- up
- Hydraulic Reservoir
- Piston (Traction) Pump Control Assembly
- Hydraulic Pump Assembly
- Piston (Traction) Pump Service
- Gear Pump Service
- Hydraulic Pump Drive Shaft
- Hydraulic Pump Drive Shaft Cross and Bearing Service
- Front Wheel Motors
- Front Wheel Motor Service
- Rear Wheel Motors (Machines with Optional CrossTrax Kit)
- Rear Wheel Motor Service (Machines with Optional CrossTrax Kit)
- Control Manifold Cartridge Valve Service
- Lift Control Manifold
- Lift Control Manifold Service
- CrossTrax AWD Manifold
- CrossTrax AWD Manifold Service
- Lift Cylinders
- Lift Cylinder Service
- Steering Control Valve
- Steering Control Valve Service
- Steering Cylinder
- Steering Cylinder Service
- Hydraulic Oil Cooler
- Sauer-Danfoss LPV Closed Circuit Axial Piston Pumps Repair Manual
- Sauer-Danfoss LPV Closed Circuit Axial Piston Pumps Service Instructions
- Eaton Delta Motors Parts and Repair Manual
- Parker Torqmotor Service Procedure (TC, TB, TE, TJ, TF, TG, TH, and TL Series)
- Sauer-Danfoss Steering Unit Type OSPM Service Manual
- 5 - Electrical System
- Table of Contents
- General Information
- Electrical System Operation
- Special Tools
- InfoCenter Display
- Troubleshooting
- Electrical System Quick Checks
- Adjustments
- Component Testing
- Ignition Switch
- 12 VDC System Fuses
- 48 VDC System Fuses
- Engine Speed Switch
- Reel Engage/Disengage Switch
- Headlight Switch
- Seat Switch
- Parking Brake Switch
- Traction Neutral Switch
- Cutting Unit Down Limit Switch
- Joystick Raise and Lower Switches
- Mow/Transport Switch
- Main Power, Glow and 48 VDC Logic Relays
- Start Relay
- Main Contactor
- Toro Electronic Controller (TEC)
- Fusible Link Harness
- Diode Assembly
- 48 VDC System Protection Diode
- Location ID Module
- Cutting Reel Motor
- CAN- bus Termination Resistors
- Hydraulic Solenoid Valve Coil
- Temperature Sender
- Oil Pressure Switch
- Fuel Actuator
- Fuel Sender
- Fuel Pump
- Service and Repairs
- 6 - Chassis
- 7 - Cutting Units
- Table of Contents
- Specifications
- General Information
- Special Tools
- Factors That Can Affect Cutting Performance
- Set Up and Adjustments
- Service and Repairs
- Cutting Reel Motor
- Backlapping
- Bedbar Assembly
- Bedknife Replacement and Grinding
- Bedbar Adjuster Service
- Cutting Reel Assembly Removal and Installation
- Cutting Reel Assembly Service
- Preparing Reel for Grinding
- Front Roller
- Rear Roller
- Roller Service
- Rear Roller Brush (Optional)
- Rear Roller Brush Drive System (Optional)
- 8 - Groomer
- 9 - Foldout Drawings