Toro Greensmaster 3250 D 04384 Specifications

3250-D to the manual 509e4b13-5f60-4ee2-8900-fa984931aa61

: Toro Toro-Greensmaster-3250-D-04384-Specifications-138998 toro-greensmaster-3250-d-04384-specifications-138998 toro pdf

Open the PDF directly: View PDF .
Page Count: 3

Download
Open PDF In Browser	View PDF

Greensmaster® 3250-D
Unmatched diesel power, innovative design and a lighter footprint make this the ideal greensmower for greens and
surrounding areas.

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

52

Greensmaster® 3250-D Specifications*
GREENSMASTER 3250-D, MODEL 04384
ENGINE
FUEL CAPACITY

Kubota® 902 tier 4i, 3-cylinder liquid-cooled diesel engine. 55.0 cu. in. (902 cc). Full pressure lubrication, oil filter. 24.8 hp (18.5 kW) @ 3600 rpm. Engine governed
to 2760 rpm high idle, 1500 rpm low idle (no load).
6 gallons (22.7 liters). Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleum blend).

TRACTION DRIVE

Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic or 3WD Series Parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.

GROUND SPEED

Forward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum
Greensmaster 3250-D transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph
(4.0 km/h) maximum.

TURF COMPACTION
STEERING
CONTROLS/GAUGES
ELECTRICAL FEATURES
SOUND LEVEL
OVERALL DIMENSIONS
TIRES
LEAK DETECTION
BACKLAPPING
BRAKES

10 psi (.68 bar) average at recommended minimum tire pressures, with a 200 lb. operator, and cutting units down.
Power steering. No-tool quick adjust steering arm position, with arm motion allowing a wide range of operator sizes. Steering cylinder has through shaft design for
accurate straight line steering.
Raise/lower-mow lever. Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter
and 4 bulb warning cluster. Hand operated choke, throttle. Mechanical engine speed control.
Maintenance-free 12-volt battery with 530 minimum cold cranking amps at 0° F (-17.7° C) and 95 minutes minimum reserve capacity at 85° F (29.4° C) 40 amp
alternator, circuit fused at 40 amps. Ignition switch/key. Seat switch. High temperature engine kill override switch. Harness terminals, fuse slot, and console switch
location available for optional lights installation.
84 dBA at operator ear under normal conditions.
	
	
	
	
	

Width of Cut:	
Wheel Tread:	
Wheel Base:	
Overall Length (w/baskets):	
Overall Width:	

59.0" (150 cm)	
50.5" (128 cm)	
48.6" (123 cm)	
93.9" (238 cm)	
68.0" (173 cm)

Overall Height:	
77.5" (197 cm)
Net Weight (no fuel, no operator):	 1,216 lbs. (552 kg)
Reel Speed:	
Approx.1950 rpm @ 2760 rpm (Adjustable)

Three 19 x 10.5-8, 2 ply pneumatic tubeless demountable and interchangeable. Smooth tread (approx. 1290 rev/mile). 8-12 psi front; 8-15 psi rear.
Turf Guardian™ optional.
Standard equipment.
6" (15.2 cm) drum type mechanical with rack and pawl lock for parking.

SEAT

Contour seat with high backrest. 7" (17.8 cm) fore/aft slider adjustment with two mounting positions, allowing 9" (22.8 cm) total seat travel. Operator manual tube
mounted on the seat back for easy access.

ROPS

Roll over protection system standard.

CERTIFICATION
WARRANTY

Certified to meet ANSI specification B71.4-2012 and European CE standards with appropriate kits installed.
Two-year limited warranty. Refer to the Operator’s Manual for further details.

8 BLADE DPA CUTTING UNITS, 04618
11-BLADE DPA CUTTING UNITS, 04619 14-BLADE CUTTING UNITS, 04624
TRACTOR
HEIGHT OF CUT (HOC) RANGE
REEL WELDMENT
REEL BEARINGS
MAINTENANCE
REEL DRIVE

These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlex 33xx/34xx series).
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit,
range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.
Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat treated to RC 48-54 hardness. The
reel is ground for diameter and concentricity, and backgrind.
Two double row, self-aligning ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft with lock nut. Multiple seal barriers on both sides of bearing for
added protection. Reel position maintained by a wave washer with no adjusting nut.
No grease zerks, sealed bearing design eliminates daily maintenance.
The reel weldment shaft is a 1.375" (35 mm) diameter tube with drive inserts permanently pressed in both ends. A replaceable floating coupler with an internal eight
tooth spline is factory installed on the right end, and held in place by a snap ring. The floating coupler may be moved to the other end when the cutting unit is used
on the GR3250-D front right position.

FRAME
AGGRESSIVENESS
BEDKNIFE
BEDKNIFE ADJUSTMENT

Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.

FRONT & REAR ROLLERS

Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced roller.
Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.

GRASS SHIELD
TOTAL WEIGHT

Aggressiveness stays constant throughout the life of the reel. Patented design.
Replaceable single edged EdgeMaxTM Microcut Bedknife is standard.
Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm) bedknife movement for each position.

Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.
8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller. 14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.

*Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

53

The Greensmaster 3250-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.

Greensmaster® 3250-D Accessories*
GREENSMASTER 3250-D ACCESSORIES
TRACTION UNIT ACCESSORIES

CUTTING UNIT & REEL OPTIONS

BEDKNIFE & BEDBAR OPTIONS

04477

3-Wheel Drive Kit

04618

8-Blade Cutting Unit

93-4262

Microcut Bedknife

04479

Thatching Reel (Set of 1)

04619

11-Blade Cutting Unit

93-4263

Tournament Bedknife

04494

Greens Spiker Kit

04624

14-Blade Cutting Unit

93-4264

Low Cut Bedknife

04495

Greens Tri-Roller Kit

119-4103

8-Blade Reel (Individual)

94-6392

High Cut Bedknife

30707

Armrest Kit

121-6651

8-Blade Reel, Heavy-Duty (Individual)

63-8600

Fairway Bedknife

99-4506

Traction Tires

119-4104

11-Blade Reel (Individual)

108-4303

Extended Microcut Bedknife

104-7701

Hydraulic Oil Cooler Kit

127-2202

14-Blade Reel (Individual)

108-4302

Extended Tournament Bedknife

04554

Light Kit

115-1880

EdgeMaxTM Microcut Bedknife (Standard)

120-1951

Spark Arrestor

GROOMER OPTIONS

115-1881

EdgeMaxTM Tournament Bedknife

Leak Detector

04709

Groomer Drive (LH) (Set of 1)

112-7475

EdgeMaxTM Fairway Bedknife

112-0279

Front Wheel Weight Kit

04710

Groomer Drive (RH) (Set of 1)

106-2648-01

Bedbar (Standard)

100-6442

2WD Weight Kit

04712

Groomer Reel, Spring Steel (Set of 1)

99-3794-03

Aggressive Bedbar

99-1645

3WD Weight Kit

04713

Groomer Brush (Set of 1)

100-6430

Hose Adapter Kit

04274

Greens Perfection Brush – Soft

105-9766

Radiator Screen Kit

04275

Greens Perfection Brush – Stiff

104-9400

Ground Follow Kit

112-9248

Groomer Pull Link Kit

115-4510

Bimini Folding Shade

04744

Grooming Reel - Thin Blade (Set of 1)

115-4754

Wireless Hour Meter

04497

ROLLER OPTIONS

THATCHING REEL ACCESSORIES

125-5303

Front Narrow Wiehle Roller Scraper

117-6840

Thin dynaBLADE, (1.2mm Thickness)
(Individual)
Regular dynaBlade, (2mm Thickness)
(Individual)
Replacement Kit, 1.2mm dynaBlade (36
Blades)
Replacement Kit, 2mm dynaBlade (36
Blades)

Front Wide Wiehle Roller Scraper

SCRAPER OPTIONS

117-6824
119-1128
117-6839

04626

Front Narrow Wiehle Roller (set of 3)

125-5304

121-6675

Spring Steel Kit

04627

Front Wide Wiehle Roller (set of 3)

125-5305

Front Full Roller Scraper

121-6674

Blade, Spring Steel

04625

Front Full Roller (set of 3)

115-7377

Front Narrow Wiehle Roller Scraper Brush

121-9525

Thatching Reel Quick Change Kit

04628

Solid Steel Roller Kit
(front Wiehle & rear steel rollers)

115-7378

Front Wide Wiehle Roller Scraper Brush

115-7379

Front Full Roller Scraper Brush

04629

Anti-Bobbing Roller

115-7380

Front Narrow Wiehle Roller Scraper Comb

119-2157

Bio-Hydraulic Fluid, 5 gal. (18.9 L)

71-1550

Cast Iron Rear Wiehle Roller

115-7381

Front Wide Wiehle Roller Scraper Comb

119-2158

Bio-Hydraulic Fluid, 55 gal. (208.2 L)

107-3514

Steel Wide Wiehle Roller

115-7382

Front Full Roller Scraper Comb

108-1178

Premium Hydraulic Fluid, 5 gal. (18.9 L)

121-4675

Extended Wiehle Roller

115-7383

Rear Roller Scraper

108-1177

Premium Hydraulic Fluid, 55 gal. (208.2 L)

04258

Extended Narrow Wiehle Roller

121-2260

Adjustable Rear Roller Scraper

121-6393

Premium Engine Oil SAE 10W30, 5 gal. (18.9 L)

04267

Narrow Wiehle Roller (for paspalum)

Spring Loaded Rear Roller Scraper
(Set of 3)

Premium Engine Oil SAE 10W30, 55 gal. (208.2 L)

Steel Narrow Wiehle Roller

04646

121-6392

107-3510
120-9595

Steel Rear Roller (standard)

107-9561

Anti-Bobbing Roller Scraper Kit

125-5180

DPA Rear Roller Extension Kit

04726

Rotating Rear Roller Brush (LH) (Set of 1)

04399

Turf Evaluator

120-9600

High Height of Cut Kit

04724

Rotating Rear Roller Brush (RH) (Set of 1)

125-5610

Paper – Reel

04249

Split Full Front Roller

125-5611

Shim – Reel

04250

Split Narrow Wiehle Roller

94-9010

Height of Cut Bar Assembly

BIO-HYDRAULIC FLUID / HYDRAULIC FLUID / OIL

TOOLS

*Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

54

The Greensmaster 3250-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Create Date                     : 2015:03:10 09:25:32-05:00
Creator                         : Adobe InDesign CC 2014 (Macintosh)
Modify Date                     : 2015:03:10 09:25:40-05:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2015:03:10 09:25:40-05:00
Creator Tool                    : Adobe InDesign CC 2014 (Macintosh)
Format                          : application/pdf
Document ID                     : uuid:799cfe74-8540-4348-9d60-16e181c27e03
Instance ID                     : uuid:343594ac-b50b-b846-885c-e43788d5a4a3
Producer                        : Adobe PDF Library 11.0
Page Count                      : 3

EXIF Metadata provided by EXIF.tools