Toro Reelmaster 3100 D 03170 Specifications

: Toro Toro-Reelmaster-3100-D-03170-Specifications-138665 toro-reelmaster-3100-d-03170-specifications-138665 toro pdf

Open the PDF directly: View PDF .
Page Count: 3

59

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

Reelmaster® 3100-D

The 3100-D triplex trim mower provides superb cutting, ultra comfort and ease of service – featuring

a unique rear engine layout and optional Sidewinder™ cutting units.

60

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

Reelmaster® 3100-D Specifications*

REELMASTER 3100-D, MODEL 03170 REELMASTER 3100-D, MODEL 03171 w/SIDEWINDER

ENGINE

Kubota® liquid-cooled diesel, 3-cylinder, 21.5 hp (16 kW) net @ 2500 RPM. HIgh idle: 2,600 rpm, Low idle: 1,400 rpm (+/- 50 rpm). 68.5 cu. in. (1123 cm3)

displacement. Pressurized lubrication system with 3.5 U.S. qt. (3.3 liter) capacity. Heavy-duty, radial seal air cleaner. Fuel/water separator with visible bowl.

CONFIGURATION

Rear mounted engine, front operator position. Rear mounted radiator. Two post ROPS and seat belt standard.

FUEL CAPACITY

7.5 gallons (28 liters). Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleum blend).

TRACTION DRIVE

Series/Parallel hydraulic traction circuit provides continuous 3-wheel drive, in mow and transport. Hydrostatic traction drive

provides infinitely variable speed in forward and reverse. 6 gallon (23 liter) hydraulic system capacity.

GROUND SPEED

Mow: 0-6 mph (0-10 km/h); Transport: 0-9 mph (0-14 km/h). Reverse: 0-4 mph. (0-6 km/h).

CONTROLS

Forward and reverse traction control pedals, mow/transport lever, hand activated park brake, ignition key switch, tilt steering wheel lock, PTO switch, throttle, joystick

control for cutting unit raise and lower (and for moving cutting units side-to-side on Sidewinder equipped models), cutting unit transport lock, reel speed and

backlap control knob.

GAUGES

Hour meter, fuel gauge, cluster gauge with glow plug and charge indicator lights, and low engine oil pressure and high coolant

temperature warning lights (high temperature safety shut off).

ELECTRICAL &

INTERLOCKS

12-volt, 585 cold cranking amps at 0° F (-18° C), 40 amps with regulator/rectifier. Traction pedal, operator presence in seat, PTO engage or disengage, and cutting

unit mow or transport safety interlock switches.

TIRES

Front: 20 x 12-10, 4-ply Turf Tread. Rear: 20 x 10-10, 4-ply Turf Tread

FRAME

Formed steel, welded steel and steel tubing.

BRAKES

Hydrostatic service brake, hand-operated parking brake.

STEERING

Power steering with tilt steering wheel.

OVERALL

DIMENSIONS

Track Width: 55" (140 cm) Overall Height: 71" (180 cm) with ROPS

Wheel Base: 56" (142 cm) Transport Width: 80" (203 cm) in 72" (183 cm) woc

92" (234 cm) in 85" (216 cm) woc

Overall Length: 93" (248 cm) Approx. Weight with Cutting units: 1860 lbs. (844 kg)

CUTTING UNIT

CONFIGURATION

Fixed position cutting units.

Operator controlled moveable cutting units travel ±12" (30 cm)

left or right from center; total of 24" (61 cm) of infinite variability.

CUTTING UNIT

OFFSET

3" (7.6 cm) in 72" (183 cm) width of cut

10" (25 cm) in 85" (216 cm) width of cut

Maximum 15" (38 cm) in 72" (183 cm) width of cut.

Maximum 22" (56 cm) in 85" (216 cm) width of cut.

CERTIFICATION

This product complies with the American National Standards Institute (ANSI B71-4 – 2012) and European Community

specifications (CE Certified). EN ISO 5395.

WARRANTY

Two-year limited warranty, refer to operators manual for details.

27" CUTTING UNITS (03180, 03181, 03183) / 32" CUTTING UNITS (03182)

TYPE

Three hydraulically-driven, balanced, 7" (17.8 cm) diameter reels. Cutting units interchangeable to all three positions.

REEL BLADE OPTIONS

5, 8, and 11-blade reels available for 27" (68.6 cm) cutting unit. 8-blade reels available for 32" (81.3 cm) cutting unit.

HOC RANGE

Height of cut ranges .25" to 2" (.63 - 5.1 cm) standard in floating position, 1.5" to 2.5" (3.8 - 6.4 cm) in fixed position.

CUTTING WIDTH

72" (183 cm), or 85" (216 cm) width of cut dependent on cutting unit selection.

CLIP FREQUENCY/

BACKLAPPING

Manually controlled variable reel speed for adjustment of clip frequency. Standard on-board backlapping.

BEDKNIFE-TO-REEL

ADJUSTMENT

Dual point adjustment (DPA) of bedknife to reel.

ROLLERS

Full roller standard on rear of cutting unit and plastic front Wiehle roller.

The Reelmaster 3100-D is manufactured

in Tomah, WI ISO 9002 Certified Plant.

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.

Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.

61

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

TRACTION UNIT ACCESSORIES

30358 Bimini Canvas Sunshade

115-4754 myTurf® Wireless Hour Meter Assembly

32" (81 CM) DPA CUTTING UNIT ACCESSORIES

03187 Rear Roller Brush Kit

115-8282 5-Blade Service Reel

114-9369 Rear Roller Scraper Kit

114-9373-03 Wiehle Roller Scraper

114-9377 Comb/Scraper Kit

115-0849 High HOC Brush

114-9384 Full Front Roller

114-9387-03 Full Front Roller Scraper

119-0640 Shoulder Roller Asm

114-9382-03 Shoulder Roller Scraper

119-4288 Short Rear Roller Asm

119-0646-03 Fixed Plate (2 per cutting unit)

119-0649 Trim/HD Collar Kit (6 per roller)

119-0635 RM3100 Tipper Roller Kit

98-1852 Gauge Bar

BEDKNIFE OPTIONS

114-9388 Standard (27") - Production

114-9389 Standard (32") - Production

112-8910 EdgeMax™ (27")

112-8956 EdgeMax™ (32")

114-9390 Heavy-Duty (27")

114-9391 Heavy-Duty (32")

120-1641 Extended Low-Cut (27")

120-1642 Extended Low-Cut (32")

CUTTING UNIT OPTIONS

03180 27" (69 cm) 5-Blade DPA Cutting Unit

03181 27" (69 cm) 8-Blade DPA Cutting Unit

03183 27" (69 cm) 11-Blade DPA Cutting Unit

03184 27" (69 cm) Verticutter Cutting Unit

03182 32" (81 cm) 8-Blade DPA Cutting Unit

27" (69 CM) DPA CUTTING UNIT ACCESSORIES

03186 Rear Roller Brush Kit

03185 Grass Basket Kit

114-9368 Rear Roller Scraper Kit

114-9372-03 Wiehle Roller Scraper

114-9376 Comb/Scraper Kit

119-0630 Shoulder Roller Asm

114-9381-03 Shoulder Roller Scraper

114-9383 Full Front Roller

114-9386-03 Full Front Roller Scraper

119-4286 Short Rear Roller Asm

115-0838 High HOC Brush

119-0646-03 Fixed Plate (2 per cutting unit)

119-0649 Trim/HD Collar Kit (6 per roller)

119-0635 RM3100 Tipper Roller Kit

98-1852 Gauge Bar

Reelmaster® 3100-D Accessories*

The Reelmaster 3100-D is manufactured

in Tomah, WI ISO 9002 Certified Plant.

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.

Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.