Toshiba Ga 1170 Users Manual Service
2014-12-13
: Toshiba Toshiba-Ga-1170-Users-Manual-130865 toshiba-ga-1170-users-manual-130865 toshiba pdf
Open the PDF directly: View PDF 
.
Page Count: 37
| Download | |
| Open PDF In Browser | View PDF |
NETWORK EXPANSION KIT GA-1170 File No. SME04003700 R04122173800-TTEC Ver00_2005-02 © 2005 TOSHIBA TEC CORPORATION All rights reserved Parts marked with “ ” are important for maintaining the safely of the machine. Be sure to replace these parts with the replacement parts specified to maintain the safety and performance of the machine. General Precautions for Installation/Servicing/Maintenance for the GA-1170 The installation and service should be done by a qualified service technician. 1. When installing the GA-1170 to the Equipment, be sure to follow the instructions described in the "Unpacking/Set-Up Procedure for the GA-1170" booklet which comes with each unit of the GA-1170. 2. The GA-1170 should be installed by an authorized/qualified person. 3. Before starting installation, servicing or maintenance work, be sure to turn OFF and unplug the equipment first. 4. When servicing or maintaining the GA-1170, be careful about the rotating or operation sections such as gears, pulleys, sprockets, cams, belts, etc. 5. When parts are disassembled, reassembly is basically the reverse of disassembly unless otherwise noted in this manual or other related materials. Be careful not to reassemble small parts such as screws, washers, pins, E-rings, toothed washers to the wrong places. 6. Basically, the machine should not be operated with any parts removed or disassembled. 7. Delicate parts for preventing safety hazard problems (such as switches, sensors, etc. if any) should be handled/installed/adjusted correctly. 8. Use suitable measuring instruments and tools. 9. During servicing or maintenance work, be sure to check the serial No. plate and other cautionary labels (if any) to see if they are clean and firmly fixed. If not, take appropriate actions. 10. The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband, because the ICs on it may be damaged due to static electricity. Before using the wrist band, pull out the power cord plug of the equipment and make sure that there is no uninsulated charged objects in the vicinity. 11. For the recovery and disposal of used GA-1170, consumable parts and packing materials, it is recommended that the relevant local regulations/rules should be followed. 12. After completing installation, servicing and maintenance of the GA-1170, return the GA-1170 to its original state, and check operation. CONTENTS [ 1 ] CONFIGURATION ................................................................................ 1 - 1 [ 2 ] SPECIFICATIONS................................................................................. 1 - 1 [ 3 ] UNPACKING AND INSTALLATION ....................................................... 3 - 1 [ 4 ] SETUP IN A WINDOWS ENVIRONMENT ............................................ 4 - 1 [ 5 ] UPDATING NETWORK BOX FIRMWARE ............................................ 5 - 1 [ 6 ] TROUBLE CODE .................................................................................. 6 - 1 [ 7 ] CIRCUIT DIAGRAM .............................................................................. 7 - 1 [ 8 ] PWB PARTS LAYOUT .......................................................................... 8 - 1 sec01.fm 1 ページ ２００５年１月１８日 火曜日 午後１０時２３分 [ 1 ] CONFIGURATION e-STUDIO162/162D e-STUDIO151/151D GA-1170 [ 2 ] SPECIFICATIONS 1. BASIC SPECIFICATIONS ITEMS Extensible model ITEMS SPEC Accessories e-STUDIO162/162D e-STUDIO151/151D Standard memory 64MB Expansion memory DIMM 1slot 144pin 128/256MB SO-DIMM Platform of Client PC IBM PC/AT compatible, Macintosh Useable OS Windows98/Me/NT4.0/2000 professi onal/W indows XP Ho me Edition/Professional Edition Bundle software (System) The conditions of each OS which can be used are required. (HDD) Exceeding 100M is recommended. (Monitor) 800 x 600 dots (Interface) 10BASE-T/100BASE-TX Ethernet Required software Internet Explorer 5.5 or later Netscape Navigator 6 or later Extensible option PS extensible kit (GA-1180) Network Protocol TCP/IP, IPX/SPX, NetBEUI, Ether Talk Disk3:Application CD-ROM • Desktop Document Manager (3 license) PCL/PS Network Scan (The functions Scan to E-mail, Scan to FTP, which can be used differ by Scan to Desktop The MFP connected) E-mail alert status Yes (Cancels by the soft key) Power supply Supplies via copier (AC power supply built-in) AC120mA Power consumption 5.5W Outside dimension (W x D x H) 248mm x 127mm x 59mm Disk1:Driver CD-ROM for e-STUDIO162/162D, e-STUDIO151/151D • PCL driver (Win) • PS driver (Win/Mac) • SMON (Win) • PAU (Win) • NIC Manager (Win) • Online manual (Win/Mac) Disk2:Network setting CD-ROM • NIC Manager (Win) • Quick Setup (Win) • SC-Print2000 (Win) • Online manual (Win/Mac) • Setup Utility (Mac) Emulation (The functions PCL/PS (PS:Cancels by the soft key) which can be used differ by The MFP connected) Network Print USB cord x 1 (for connection to Copier) Software CD-ROM x 3 Screw for installation x1 Clamp x 1 (for harness fixation) Installation manual Installation guide *An installation manual exists in driver CD-ROM by the pdf file format. Mac OS 8.6-9.x,10.1.5,10.2-10.2.8(w/ o 10.2.2)(PS option) Required hardware(PC) SPEC GA-1170 CONFIGURATION 1–1 sec01.fm 2 ページ ２００４年１２月７日 火曜日 午後４時１１分 2. FUNCTION DESCRIPTION A. PRINT EMULATION A difference exists in the function which can be used by execution of the basic performance and composition of the MFP to connect (print size/configuration). (1) comparison table of main print function classified by driver Function General Document Style PCL6 (XL)/ SPDL2 Custom Driver PCL5e Custom Driver PS Custom Driver 1-Sided, 2-Sided(Book), 2-Sided(Tablet) Yes No Binding Edge No N-up Graphic Z Z, Reverse Z, N, Reverse N Z Custom Paper Size 1size 3 sizes Different 1st (Cover) Yes No 600/300 dpi Half tone Setting Graphics Mode 600dpi No Raster/HP-GL2 Yes No Raster/Vector No Negative Image No Yes Mirror Image No Yes Fit to Page X Yes Resident Font 136 fonts, 5 Kanji fonts (Japan only) 80 fonts Download font Others Win 9x : 2/4 Win2K/XP: 2/4/6/8/16 2/4/6/8/16 Resolution Setting Font Windows PPD file 1-Sided, 2-Sided(Book) 2-Sided(Tablet), Pamphlet Style(Tiled Pamphlet), Pamphlet Style(2-up Pamphlet) Booklet N-up Order Macintosh PPD file 35 fonts, 5 Kanji fonts (Japan only) 136 fonts, 5 Kanji fonts (Japan only) No Yes Yes Configuration Setting Yes (Automatic) No Job Compression No Yes No Bitmap Compression No Yes No (2) comparison table of printing function for each driver The model to connect Function General e-STUDIO162/162D, e-STUDIO151/151D PCL5e PCL6 PS Copies Orientation Win PPD Portrait/Landscape Collate Collate/Group Document Style 1-Sided, 2-Sided(Book), 2-Sided(Tablet), Pamphlet Style(Tiled Pamphlet), Pamphlet Style(2-up Pamphlet) Booklet (e-STUDIO162/162D, e-STUDIO151/151D) Invoice on Letter, A5 on A4, Letter on Letter, A4 on A4 Binding Edge 1-Sided, 2-Sided(Book), 2-Sided(Tablet) No No Margin Shift No N-up N-up order Mac PPD 1-999 2/4/6/8/16 Z Z, Reverse Z, N, Reverse N GA-1170 SPECIFICATIONS 1–2 Win9x: 2/4 Win2k/XP: 2/4/6/8/16 *2 Z sec01.fm 3 ページ ２００４年１２月７日 火曜日 午後４時１１分 The model to connect e-STUDIO162/162D, e-STUDIO151/151D Function PCL5e PCL6 PS On/Off Mac PPD Win PPD Yes (Single hairline/Single thin line/Double hairline/Double thin line) On/Off *2 General N-up Border Paper Paper Size (e-STUDIO162/162D, e-STUDIO151/151D) A3/B4/A4/B5/A5/B6/A6/11x17/8.5x14/8.5x13/8.5x11/5.5x8.5/Folio/Executive/COM-10/Monarch/DL/C5/8K/16K Fit to Page size (e-STUDIO162/162D, e-STUDIO151/151D) A4/B5/A5/B6/A6/8.5x14/8.5x13/8.5x11/5.5x8.5/Folio/Executive/COM-10/Monarch/DL/C5/8K/16K Paper Type No Custom Paper Size 1size *1 1 size Source Selection Auto/Bypass (Auto) e-STUDIO162/162D, e-STUDIO151/151D: Different 1st (cover) No No Carbon Copy No Paper Output Output Tray Selection No Graphic Resolution Setting Staple No 600/300 dpi Half tone Setting Graphic Raster HP-GL2 No Smoothing No Toner save No Half tone Enhance No Brightness No Negative Image No Mirror Image No Resident Font Download Font No Screen Frequency 8 to 360.0 in 0.1 steps Screen angle 0.0 to 360.0 in 0.1 steps Raster Vector Fit to Page Others 600 dpi No Zoom Font Tray 1/2 On/Off Transparency Inserts Graphics Mode 3 sizes *2 On/Off Horizontal/Vertical No 25-400% On/Off No 80 fonts 136 fonts 35 fonts No Bitmap, TrueType, Graphics Configuration Setting 136 fonts Type1 True Type Yes (Automatic) ROPM No On/Off Overlay On/Off No Print Auditor No Job Retention No Watermark On/Off On/Off(With functional restriction) Page Protection No Job Compression No None, Fastest, Fast, Medium, Best No Job Compression No None, Very High, High, Medium, Draft No *1:Mac OS 10.1 is not supported. *2:Windows NT is not supported. GA-1170 SPECIFICATIONS 1–3 sec01.fm 4 ページ ２００４年１２月７日 火曜日 午後４時１１分 (3) PDF/TIFF direct printing function B. PDF and TIFF files can be specified from a web page and directly printed out. It is possible to use the MFP scanning function as a network scanner with a network scanner expansion kit. Setups can be made using a Web browser. Supported functions vary with the type of the MFP connected. (4) Limitations (printing function) If a print request for GDI/SPLC data is made, an error message is printed out. NETWORK SCANNING FUNCTION (1) Basic scanning function (5) Printer condition setup Function Item e-STUDIO162/162D, e-STUDIO151/151D Network scanner Scan to E-mail Yes Scan to Desktop Yes Scan to FTP server Yes Specify e-mail address with LDAP Yes AdHoc (Enter e-mail address from MFP.) Yes JPEG PDF (non-compression, G3, G4) TIFF (non-compression,G4, G4) Yes The following setup can be made from the web page. Default Setting Items Item Function e-STUDIO162/162D, e-STUDIO151/151D Copies 1-999 Orientation Portrait / Landscape Default Paper Size (Overseas) • Invoice • Letter • Foolscap • Legal (Domestic) • A5 • B5 • A4 (China - size of AB system) • A5 • B5 • A4 • 16K Default Paper Source Disable Blank Page Print Default 1 Destination Portrait Letter or A4 File format drop down box select values: • AUTO • Tray1 • Tray2 • BYPASS AUTO Enable/Disable Disable Item Default e-STUDIO162/162D, e-STUDIO151/151D e-STUDIO162/162D, e-STUDIO151/151D Scanning size *When destination language is Japanese. d ro p do wn b ox slect values: • 1-SIDED • 2-SIDED (BOOK) • 2-SIDED (TABLET) 1-SIDED ROPM Enable / Disable Disable TIFF/PDF multiple page support (2) Scanner settings Setting 2-Sided Print Remarks JPEG color/JPEG gray scale/PDF color/PDF gray scale/PDF monochrome, binary non-compression/PDF monochrome, binary G3 compression/PDF monochrome, binary G4 compression/TIFF color/TIFF gray scale/TIFF monochrome, binary non-compression/TIFF monochrome, binary G3 compression/TIFF monochrome, binary G4 compression TIFF monochrome, binary G4 compression Color mode Monochrome, 2 gradations/Gray scale/Full color Monochrome, 2 gradations Available only at the “monochrome”. Resolution 75/100/150/200/ 300/400/600 75 Selectable resolutions vary with different memory capacities. B/W threshold 1-254 (default: 128) 128 The network status pages shows a list of settings about the network. Data are printed out in the A4 or letter size in US English regardless of the destination and OS language selected. The status page can be printed out by pressing the status switch on the network expansion kit. Note: 1. The name of the printer is printed under the item "printer name." 2. When WINS is disabled, "WINS server 1-5" is not displayed. It is displayed when a value is set or information is acquired from the DHCP server. "WINS server" shows up to 5 values: 2 settings, 2 DHCP values, and broadcast. However, the broadcast operates only when no normal response is returned from any server. 3. The "WINS Scope ID" is displayed only when a value is set or when information is acquired from the DHCP server and more than one piece of information is valid as a WINS server. GA-1170 SPECIFICATIONS 1–4 A4 (AB region) Letter (Inch-system region) File format (6) Network status page Any server which responds normally to the registration of WINS is marked with an asterisk "∗". Remarks sec01.fm 5 ページ ２００４年１２月７日 火曜日 午後４時１１分 Setting Item Default e-STUDIO162/162D, e-STUDIO151/151D e-STUDIO162/162D, e-STUDIO151/151D Light source Red/ Green/ Blue Void On/Off White/ Red/ Green/ Blue Green White On (4) Recipient registration [e-STUDIO162/162D, e-STUDIO151/151D] Remarks • Up to 200 destinations can be registered on the network expansion kit to which the scan can be sent from the network scanner. Light source can be selected only when the color mode is in "Monochrome". • The mail address registered for each destination can be selected from the mail address which is searched using LDAP. • The information for each recipient includes the recipient name, IP address or mail address, scanning size, format type, and scan parameter. When On is selected, the edges of images are cut. • Either of LDAP-selected or directly-entered mail address scan setting is available. If the destination is a mail address entered through the main system or selected by LDAP, this scan setting is used. (3) Send file (message and filename) • Information contained in filename • The destination name is displayed on the LCD. Sender name : Use MFP product name. Date & Time : Date and time at which file is sent Session page counter : Unique identifier : Automatically created based on the information of the date and time and image send counter. (5) Scanning size [e-STUDIO162/162D, e-STUDIO151/151D] Image send counter • Scanning size is the size set up in main unit(Copier). (Apply to the main scan, a subscan, ADF, and OC) (6) Scanner limitations [e-STUDIO162/162D, e-STUDIO151/151D] Example: e-STUDIO162D_20000620_155114_0057_06a3f3393948.pdf • The scanning function is allocated to the network expansion kit. The b Button Manager settings are disabled. • Mail subject • When the network expansion kit is connected, the scanner function through TWAIN (pull scan) and push scan which used button manager on pc are not available. Can be freely set. Default: Scanned image. device name: e-STUDIOXXX (MFP product name) Example: Scanned image. device name: e-STUDIO162D • Mail message The following messages are added to the image send mail. Device name: Freely set Model: MFP product name Location: Freely set File type: File type of send image Resolution: Resolution of send image Example; Device name :e-STUDIO162D Model name :e-STUDIO162D Location :D2) Planning dept. File type :PDF MMR (G4) Resolution :200 dpi x 200 dpi GA-1170 SPECIFICATIONS 1–5 sec01.fm C. 6 ページ ２００４年１２月７日 火曜日 午後４時１１分 FUNCTIONS BY INTERFACE F. When the network expansion kit is connected, the following functions are available by system interface. System I/F (main unit) USB2.0 SPLC Net Scan No No Yes Yes Yes Yes No No No No IEEE1284 ➝ Yes No No No No USB2.0 ➝ Yes No No No No USB1.1 IEEE1284 [e-STUDIO162/162D, e-STUDIO151/151D] 1) Connection to the system unit PCL5e/6 PS (*1) ➝ IEEE1284 RJ45 (LAN) GDI USB1.1 USB1.1 Supplied by the main unit Function GA-1170 I/F RJ45 (LAN) ➝ No No Yes No RJ45 (LAN) ➝ No No No Yes Yes (*2) Yes (*2) No No Yes (*2) Yes (*2) No HARDWARE SETUP No • Connect to the USB2.0 port 2) Power supply Supplied by the main unit. No No No No (*1): PS requires soft keys of the GA-1180. (*2): Some functions are not available. D. NETWORK SETUP Network setups should be performed by the system administrator. Use a setup tool such as TCP/IP, Netware, Ether Talk or Web interface. E. SOFTWARE SETUP The network expansion kit can be installed by setting up NIC, installing a printer driver with the total installer, and installing Desktop Document Manager. (1) Installing driver The network expansion kit printer is connected only through the network. The port setup required for installing a printer driver is the network only. The following items should be set up. • TCP/IP peer-to-peer port 1) Search for the network expansion kit on the network and select the network expansion kit you want or enter the IP address of the applicable network expansion kit to create a TCP/IP port. 2) Install the driver to the created port. • Windows printer shared port When the setup of the above client PC is completed and the printer is set to "Windows shared printer," other client PCs can select this printer shared port and then proceed to installation of the driver. GA-1170 SPECIFICATIONS 1–6 sec03.fm 1 ページ ２００５年１月２５日 火曜日 午前１０時５５分 [ 3 ] UNPACKING AND INSTALLATION The unpacking and set-up procedure shall be done by a qualified service technician. 1. UNPACKING 3. INSTALLATION PROCEDURE This installation procedure is provided for e-STUDIO162/162D, e-STUDIO151/151D. For Installation to other models, see the operation manual of the main unit or the service manual. Turn off the main switch of the main unit and remove the power plug of the copier from the outlet. 1. Cut the rear cabinet. 1) Remove the ADF/ RADF from the main unit and gently place it on the document glass as shown in the illustration. 2) Cut out two cut-out portions from the rear cabinet using a cutter or the like. 3) Use a Phillips screwdriver or the like to open a hole. 4) Remove the screw and then remove the rear cabinet cover. 5) Cut out a part of the rear cabinet cover with nippers or the like as shown in illustration. (Be careful about the orientation of the nippers so that the cross section is flat.) 2. PACKAGED GOODS Parts included CD-ROM ... 3 pcs. Network expansion kit Screw (3 x 14) ... 1 pc. 2. Attach the network expansion kit. USB cable ... 1 pc. Clamp ... 1 pc. 1) Engage the two pawls on the rear of the network expansion kit with the cutout portions of the main unit and secure the kit with the supplied screw (3 x 14). Important information ... 1 sheet 2) Connect the connector of the network expansion kit to the connector of the main unit. 3) Secure the rear cabinet cover to the main unit with the screw. 4) Attach the ADF/ RADF to the main unit. GA-1170 UNPACKING AND INSTALLATION 3–1 sec03.fm 2 ページ ２００４年１２月７日 火曜日 午後４時４分 3. Connect the USB cable and the network cable. 1) Attach the supplied cable clamp to the position shown in the illustration. 2) Connect the USB cable to the network expansion kit and the main unit. At this time, reduce slack of the cable with the cable clamp as shown in the illustration. 3) Connect the network cable. Insert the power plug of the copier to the outlet, turn the main switch of the copier to the “ON” position, and then perform network setting and installation of the software. GA-1170 UNPACKING AND INSTALLATION 3–2 sec04.fm 1 ページ ２００４年１２月７日 火曜日 午後４時４分 [ 4 ] SETUP IN A WINDOWS ENVIRONMENT 1. SETTING THE IP ADDRESS OF THE MACHINE 8) Click the "NICManager" button. Before installing the printer driver, be sure to set the IP address of the machine. Consult your network administrator for the correct IP address, subnet mask, and default gateway to be entered. If a DHCP server will automatically assign an IP address to the machine, the following procedure is not necessary. (To check the IP address assigned to the machine by DHCP, see "2. CHECKING THE IP ADDRESS" .) Note: If the machine is used in a DHCP environment, the machine's IP address may change automatically. If this happens, printing will no longer be possible. In this event, use a WINS server or do not use the machine in a DHCP environment. 1) Make sure that the LAN cable is connected to the machine and then turn on the machine. 2) Insert the network expansion kit GA-1170 "Software" CD-ROM into your computer's CD-ROM drive. 3) Click the "start" button, click "My Computer" ( click the CD-ROM icon ( ). ), and then double9) The printer or printers connected to the network will be detected. Click the printer to be configured (the machine). In Windows 95/98/Me/NT 4.0/2000, double-click "My Computer" and then double-click the CD-ROM icon. 4) Double-click the "setup" icon ( Select the "GA-1170". ). Note: If the language selection screen appears after you double click the "setup" icon, select the language that you wish to use and click the "Next" button. (Normally the correct language is selected automatically.) 5) The "SOFTWARE LICENSE" window will appear. Make sure that you understand the contents of the license agreement, and then click the "Yes" button. 6) Read the message in the "Welcome" window and then click the "Next" button. 10) Click the "Print Server Card Setup" button. 7) Click the "Administrator Tools" button. Enter your password in the password entry screen and click "OK". The Print Server Card Setup window will appear. The password for this product has been initially set to "TOSHIBA". If the "Guest user" checkbox is selected, the settings can be viewed but not configured. 11) Click the "TCP/IP" tab. GA-1170 SETUP IN A WINDOWS ENVIRONMENT 4–1 sec04.fm 2 ページ ２００５年１月２７日 木曜日 午後７時１６分 3. PRODUCT KEY SETTING 12) Configure the settings and then click the "Update" button. To enable the PS3 function and the e-mail status & alerts function, follow the procedures below. In addition, to enable the PS3 function, you need GA-1180 (option). 1) Make sure that the LAN cable is connected to the machine and then turn on the machine. 2) Enter the IP address in web browser to open the web page. 3) Select "Product Key Setting" in "Device Setup" from MENU. Be sure to ask your network administrator for the correct IP address, subnet mask, and default gateway to be entered. 13) Your changes to the settings appear. Make sure that the changes are correct and then click the "OK" button. 14) Restart the machine. 4) Set "User name" to "admin" and "Password" to "TOSHIBA" in the screen displayed. Power off the machine and then power it back on. 15) Select "Search" from the "File" menu. 5) Click the "OK" button to obtain the "Product Number". The IP address that you entered will appear. Make sure that it is correct. The completes the IP address settings. 2. CHECKING THE IP ADDRESS To check the IP address of the machine, press the status button on the network expansion kit to print out a network status page. 6) Fill in the product number in the following column of the product sheet (MACHINE SERIAL NUMBER). APPLICATION NUMBER MACHINE SERIAL NUMBER PRODUCT KEY XXXXXXXXX 7) Obtain the product key with APPLICATION NUMBER and MACHINE SERIAL NUMBER in the product sheet. For specific procedure to obtain the product key, contact the TOSHIBA authorized dealer. In addition, keep the product sheet after filling in since the product key is important information. 8) Enter the product key in the web page displayed in 5), and click the "Submit" button. This completes the PS3 setting. 9) Select "E-mail status & alerts" from the "Option Name" list in the "Product Key Setting" screen. 10) Click the "Submit" button. This completes the e-mail status & alerts function setting. GA-1170 SETUP IN A WINDOWS ENVIRONMENT 4–2 sec05.fm 1 ページ ２００５年１月１８日 火曜日 午後１０時３９分 [ 5 ] Updating Network Box Firmware The page changes to the Network Box firmware upload mode. Update the Network Box firmware in the following procedure using a Web browser. The browser is automatically reloaded and then the screen looks like this. 1. Display the web page for updating Network Box firmware *When the screen shown in fig.3 is not displayed, refresh a browser manually. Start the browser on your PC and specify the following URL. A web page, as shown in Fig. 1, appears on screen. http:///firmware_upload.html [Fig. 3: Upload mode] [Fig.1: Web page for updating Network Box firmware] 3. Specifying the file 2. Switch to firmware upload mode Click the Browse button. Selects the firmware of the Network Box version you want to update, from the file selection menu indicated in Fig.4. Click the button on the screen, the message shown in Fig. 2 appears. [Fig. 4: Specifying the file] Note: If you want to set the IP address of the Network Box at first, use the NIC Manager. Select and set your model name and an appropriate Ethernet address from the list. Both the Boot and Main files can be updated in the same procedure as mentioned above. However, when you want to update both at the same time, you need to update them separately by repeating the same procedure twice. When updating both files, it is required to first update Boot and then Main. [Fig.2: Switch to firmware upload mode] GA-1170 Updating Network Box Firmware 5–1 sec05.fm 2 ページ ２００５年１月１８日 火曜日 午後９時８分 Caution: If a DHCP is used, the browser may not be able to reload automatically in some cases when transferring to the upload mode because different IP addresses are read. Therefore, we recommend that you use a fixed IP address when updating firmware. 4. Updating the firmware After you select the file, click the Submit button. The firmware is transmitted to Network Box, and it is updated. The message indicated in Fig.5 blinks repeatedly until the updating process is completed. Do not turn off the power supply. If the upload mode is operating with different IP addresses, check the IP address obtained by the Ethernet address of Network Box from the DHCP server and display the updating mode URL again using the browser. When a proxy server is used, the screen may not be updated by reloading. In that case, you need to update manually. [Fig.5: Updating in progress] 5. Restarting your MFP When updating is completed, the message shown in Fig.6 appears on screen. Turn off the power and then turn it on again to restart Network Box. [Fig.6: Updating completed] GA-1170 Updating Network Box Firmware 5–2 sec06.fm 1 ページ ２００４年１２月８日 水曜日 午前１０時２４分 [ 6 ] TROUBLE CODE 1. TROUBLE CODE (CE CODE) If "CE" blinks in the display, press the [START] key. An error code will appear.(Only e-STUDIO162/162D, e-STUDIO151/151D displays an error code automatically.) Solve the problem as explained below. Error Code Solution CE-00 Error which cannot be specified occurred. Turn off the power and turn it back on. Consult with your network administrator to make sure that no problems exist on the network or in the server. CE-01 Network Server card error. Turn off the power and turn it back on. Consult with your network administrator to make sure that no problems exist on the network or in the server. CE-02 Server access denied. The scanned image was not sent because a connection to the server could not be established. Make sure that the SMTP server settings or FTP server settings in the Web page are correct. CE-03 The scanned image was not sent because the server was busy or there was too much traffic. Wait briefly and then try again. CE-04 It has not logged in to the FTP server and the mail server. Please reconfirm the login name and a password. CE-05 The scanned image was not sent because the directory of the destination FTP server was not correct. Make sure that the correct FTP server information is configured in the Web page. CE-09 The size of the scanned image file exceeds the upper limit set in "Maximum Size of File" in the Web page. Reduce the number of original pages scanned into the file, or change the upper limit set in "Maximum Size of File". CE-10 A transmission method assigned to a [SCAN MENU] key cannot be used. Check the transmission methods assigned to the [SCAN MENU] keys in "Enable Scanner Delivery to:" in the Web page whether or not the method can be used. CE-11 The memory filled with scanner data. It was not able to process by the size of a scanner data being too large. Please drop resolution of data by setup of scaner and retry scan. CE-12 The quantity of the result for which LDAP searched ex ceeded th e m aximu m quantit y which can be searched. There are too many addresses which were in agreement with reference conditions. Please increase the number of reference characters and perform re-reference. GA-1170 TROUBLE CODE 6–1 A B C 8 DP83816 (MAC/PHY) USB2.0 ISP1561 (RS-232C Connector) 4Pin Connector OSC 25MHz 7 12MHz LCX14 PCI BUS 33MHz/32bit UART PCIC 6 Bridge IRC EBUSC PIO EBIF SDRAMC Tx49Core G-Bus IM-Bus PCI Connector Ethernet Connector USB Connector CPUCLK = 200MHz 5 ACE BUSSPRT DATA[63:0] ADDR[19:0] 100MHz/64bit System BUS LCX244 TMPR4927TB MEMA[14:5] 4 MEMD[31:0] D LCX245 1. BLOCK DIAGRAM LCH 4 3.3V LD[31:0] LA[20:0] 3 LCX125 HC125 256MB(Max) 256Mbit RTC 2 32.768KHz 256Kbit Serial EEPROM SDRAM1 SO_DIMM SDRAM0(H) 2 256Mbit On Board 64MB 3 SDRAM0(L) MEMD[15:0] [ 7 ] CIRCUIT DIAGRAM 5 MEMD[31:16] Flash SO-DIMM slot0 12MB or 16MB 6 Flash SO-DIMM slot1 8MB MEMD[63:0] 7 Flash SO-DIMM (Mask ROM) slot2 32MB 8 UART Ch1 7–1 LCX373 CIRCUIT DIAGRAM LD[31:0] GA-1170 LD[31:0] SPD 1 1 1/16 A B C D Sec07.fm 1 ページ ２００４年１２月７日 火曜日 午後４時５分 A B C 8 VCCIO 4 1 10,16 CLK OUT 0.1uF C1 SCO-10 25MHz GND CONT VDD X1 5 8 7 13,16 9,10,11 9 13,16 VCCIO PCIINTA PCIINTB INT2 NMI 33 R16 6,16 TPAD9 RXD1 TPAD7 TPAD27 VCCIO 13,16 TP381 6 G4 J5 1 J1 H3 J4 TP655 0.1uF C2 F3 F2 F1 G3 G2 G1 F4 E1 E6 D5 P23 R26 K2 L5 L4 L3 L2 C11 B11 C12 E16 K1 1 1 TP427 TP395 TP396 10K 10K 10K 10 TP650 TP660 TP659 TP658 TP656 TPAD33 R218 VCCIO T2B-SQ NOASM JP1 1 VCCIO VCCIO TP394 R33 R34 R35 CGRESET 8.2K R20 PONRST 8.2K 7,9,10,11,13,15 TP737 TP736 TP738 8.2K R18 2 D 1K R14 10K R15 R287 1K TMPR4927TB_1 5 TMPR4927/4937 RXD0 RXD1 CTS0 CTS1 SCLK INT0 INT1 INT2 INT3 INT4 INT5 NMI TCLK SDIN1 BYPASSPLL CGRESET MASTERCLK TEST0 TEST1 TEST2 TEST3 TEST4 TXD0 TXD1 RTS0 RTS1 PIO0 PIO1 BITCLK/PIO2 SDIN0/PIO3 SDOUT/PIO4 PIO5 PIO6 PIO7 CB0/PIO8 CB1/PIO9 CB2/PIO10 CB3/PIO11 CB4/PIO12 CB5/PIO13 CB6/PIO14 CB7/PIO15 TIMER0 TIMER1 WDRST HALTDOZE TPC1 TPC2 TPC3 TX4927/TX4837 1/5 TDI/DINT TPCO/TDO TCK TMS DCLK TRST RESET PCST0 PCST1 PCST2 PCST3 PCST4 PCST5 PCST6 PCST7 PCST8 IC1A E13 D13 C13 H1 J2 H2 J3 A2 A1 B2 B1 C2 C1 D3 D1 AD3 AF3 AC20 AB21 AE3 AE4 AE20 AD21 E2 E3 M2 K3 1 VCCIO TP651 TP652 TPAD35 TP752 TP753 TP754 TP743 TP744 TP745 TP746 TP747 TP748 TP749 TP750 TP751 HALTDOZE VCCIO R299 WDRST 6,16 13,16 DIMM_SCK DIMM_SDA EEP_SCK EEP_SDA RTCCLK RTCCS RTCDATA RTCR/W DBG_LED0 DBG_LED1 DBG_LED2 DBG_LED3 PIO_SW HDD_POWER VCCWCTL 5,16 5,16 8,16 8,16 8,16 8,16 8,16 8,16 13,16 13,16 13,16 13,16 13,16 9 7,16 R36 R37 R295 NO ASM 1K 1K R288 33 4 VCCIO 10K 10K TPAD6 PIO15 TPAD8 TPAD28 TP741 R294 1 1 1 VCCIO TPAD10 TXD1 10K 3 R293 R292 33 33 33 A17 C16 B16 A16 C15 B15 E14 C14 B14 33 R291 33 R290 R289 B13 1 VCCIO 3 B12 TP742 TP639 1K R22 2. MAIN PWB 4 1K R24 5 1K 6 1K R27 7 NOASM 8 1K R296 R19 10K R17 1K R297 7–2 1K CIRCUIT DIAGRAM R298 GA-1170 R300 1 1K 1K 1K 1K R247 R248 R249 R250 2 TP710 TP711 TP712 TP713 TP714 2 1 2 3 4 5 6 7 8 9 10 RF-H102TD-1130 NOASM 1 2 3 4 5 6 7 8 9 10 CN11 1 1 2/16 A B C D Sec07.fm 2 ページ ２００４年１２月７日 火曜日 午後４時５分 GA-1170 CIRCUIT DIAGRAM 7–3 A B C D 5,6,16 MEMD[63:0] 8 TMPR4927TB_2 8 MEMD63 MEMD62 MEMD61 MEMD60 MEMD59 MEMD58 MEMD57 MEMD56 MEMD52 MEMD53 MEMD54 MEMD55 MEMD48 MEMD49 MEMD50 MEMD51 MEMD47 MEMD46 MEMD45 MEMD44 MEMD43 MEMD42 MEMD41 MEMD40 MEMD39 MEMD38 MEMD37 MEMD36 MEMD35 MEMD34 MEMD33 MEMD32 MEMD28 MEMD29 MEMD30 MEMD31 MEMD27 MEMD26 MEMD25 MEMD24 MEMD22 MEMD21 MEMD20 MEMD23 MEMD19 MEMD18 MEMD17 MEMD16 MEMD12 MEMD13 MEMD14 MEMD15 MEMD11 MEMD9 MEMD10 MEMD8 MEMD7 MEMD6 MEMD5 MEMD4 MEMD3 MEMD2 MEMD1 MEMD0 VCCIO 1 2 3 4 4 BR28 3 2 1 33 8 BR4 7 6 5 33 8 BR5 7 6 5 33 8 BR7 7 6 5 33 8 BR8 7 6 5 33 8 BR10 7 6 5 33 8 BR11 7 6 5 33 1 BR12 2 3 4 33 1 BR13 2 3 4 33 8 BR14 7 6 5 33 8 BR15 7 6 5 33 8 BR17 7 6 5 33 8 BR19 7 6 5 33 5 BR20 6 7 8 33 5 BR22 6 7 8 33 4 BR25 3 33 2 1 DATA52 DATA53 DATA54 DATA55 DATA59 DATA58 DATA57 DATA56 4 3 2 1 5 6 7 8 8 7 6 5 7 4.7K NOASM BR27 DATA63 DATA62 DATA61 DATA60 DATA48 DATA49 DATA50 DATA51 4 3 2 1 5 6 7 8 DATA47 DATA46 DATA45 DATA44 DATA28 DATA29 DATA30 DATA31 8 7 6 5 1 2 3 4 DATA27 DATA26 DATA25 DATA24 8 7 6 5 DATA43 DATA42 DATA41 DATA40 DATA22 DATA21 DATA20 DATA23 1 2 3 4 1 2 3 4 DATA19 DATA18 DATA17 DATA16 1 2 3 4 DATA39 DATA38 DATA37 DATA36 DATA12 DATA13 DATA14 DATA15 1 2 3 4 1 2 3 4 DATA11 DATA9 DATA10 DATA8 1 2 3 4 DATA35 DATA34 DATA33 DATA32 DATA7 DATA6 DATA5 DATA4 1 2 3 4 1 2 3 4 DATA3 DATA2 DATA1 DATA0 1 2 3 4 7 R41 DATA[63:0] DATA1 DMAREQ0 DMAREQ1 DMAREQ2 DMAREQ3 4.7K 6 33 16 TP366 NOASM DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 DATA8 DATA9 DATA10 DATA11 DATA12 DATA13 DATA14 DATA15 DATA16 DATA17 DATA18 DATA19 DATA20 DATA21 DATA22 DATA23 DATA24 DATA25 DATA26 DATA27 DATA28 DATA29 DATA30 DATA31 DATA32 DATA33 DATA34 DATA35 DATA36 DATA37 DATA38 DATA39 DATA40 DATA41 DATA42 DATA43 DATA44 DATA45 DATA46 DATA47 DATA48 DATA49 DATA50 DATA51 DATA52 DATA53 DATA54 DATA55 DATA56 DATA57 DATA58 DATA59 DATA60 DATA61 DATA62 DATA63 DMAREQ[3:0] DMAREQ0 DMAREQ1 DMAREQ2 DMAREQ3 R68 6 TP1 1 68pF C3 E11 B9 B8 C8 E9 AF15 N3 N1 P1 R2 T5 T2 U2 V5 W1 Y4 Y1 AA2 AB4 AB2 AC1 AE1 AF21 AD22 AF22 AF24 AE25 AD26 AC26 AA22 AA25 Y23 Y25 W25 V23 V26 T22 T25 N2 P3 R3 R1 T3 U3 U1 W2 Y5 Y2 AA5 AA1 AB3 AB1 AD2 AF2 AC22 AE22 AD24 AF25 AD25 AC25 AB25 AA24 AA26 Y24 Y26 W26 V25 U25 T23 N25 ICT32 16 R45 10 BWE0/BE0 BWE1/BE1 BWE2/BE2 BWE3/BE3 ACE CE0 CE1 CE2 CE3 CE4 CE5 CE6 CE7 SWE OE TMPR4927/4937 5 BUSSPRT DMAREQ0 DMAREQ1 DMAACK0 DMAREQ2/ACRESET DMAACK1 DMAREQ3 SYNC/DMAACK2 DMAACK3 DMADONE SDCLKIN ADDR0 ADDR1 ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 ADDR8 ADDR9 ADDR10 ADDR11 ADDR12 ADDR13 ADDR14 ADDR15 ADDR16 ADDR17 ADDR18 ADDR19 WE CKE SDCS0 SDCS1 SDCS2 SDCS3 DQM0 DQM1 DQM2 DQM3 DQM4 DQM5 DQM6 DQM7 RAS CAS SDCLK0 SDCLK1 SDCLK2 SDCLK3 ACK/REDY SYSCLK TX4927/TX4937 2/5 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 DATA8 DATA9 DATA10 DATA11 DATA12 DATA13 DATA14 DATA15 DATA16 DATA17 DATA18 DATA19 DATA20 DATA21 DATA22 DATA23 DATA24 DATA25 DATA26 DATA27 DATA28 DATA29 DATA30 DATA31 DATA32 DATA33 DATA34 DATA35 DATA36 DATA37 DATA38 DATA39 DATA40 DATA41 DATA42 DATA43 DATA44 DATA45 DATA46 DATA47 DATA48 DATA49 DATA50 DATA51 DATA52 DATA53 DATA54 DATA55 DATA56 DATA57 DATA58 DATA59 DATA60 DATA61 DATA62 DATA63 IC1B DATA[63:0] 5 ADDR0 ADDR1 ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 ADDR8 ADDR9 ADDR10 ADDR11 ADDR12 ADDR13 ADDR14 ADDR15 ADDR16 ADDR17 ADDR18 ADDR19 R59 D11 A8 A7 B7 DMAACK0 DMAACK1 DMAACK2 DMAACK3 BUSSPRT BWE_BEA0 BWE_BEA1 BWE_BEA2 BWE_BEA3 B3 ACE C5 33 1 1 1 1 TPAD15 TPAD16 TPAD17 TPAD18 R69 TPAD29 TPAD30 TPAD31 TPAD32 33 R62 R63 R64 R65 R66 R208 R209 A9 A10 B10 C10 33 33 4 33 33 33 33 33 33 33 33 33 33 ADDR[19:0] CE0 CE1 CE2 CE3 CE4 CE5 CE6 CE7 R67 47 47 33 33 33 D7 C7 C6 B6 A6 A5 B4 A4 1 1 1 1 TPAD11 16 16 R60 R61 1 CKE R51 R52 R53 R54 R55 1 BR9 2 3 4 DQM4 DQM5 DQM0 DQM1 SWE OE ACK_READY SYSCLKA WE CKE TP662 WE 1 BR6 2 3 4 16 16 SDCLK0A SDCLK1A SDCLK2A SDCLK3A DQM0 DQM1 DQM2 DQM3 DQM4 DQM5 DQM6 DQM7 DQM7 DQM2 DQM6 DQM3 33 33 R49 R50 CAS RAS 33 33 82 10pF R46 R47 R48 C246 10pF 16 16 16 C245 SDCLK0A SDCLK1A SDCLK2A SDCLK3A SDCS0 SDCS1 SDCS2 DQM0 DQM1 DQM2 DQM3 DQM4 DQM5 DQM6 DQM7 RAS CAS SDCS0 SDCS1 SDCS2 A3 M1 C4 L1 AF7 AE8 AF8 AB9 AE9 AD10 AE10 AB11 AC11 AE11 AD12 AF12 AD13 AE13 AD14 AD15 AE15 AB16 AD16 AE16 AE5 AD17 AC7 AD7 AE17 AB18 AB6 AE6 AC18 AE19 AD6 AF6 AD18 AB20 AE7 AF4 AF14 AF19 AF13 AF17 SDCS0 SDCS1 SDCS2 4 LACE 8 7 6 5 8 7 6 5 1 SDDQM4 SDDQM5 SDDQM0 SDDQM1 SDDQM7 SDDQM2 SDDQM6 SDDQM3 MEMDIR BUSSPRT ACE ROMCS0 ROMCS1 ROMCS2 ROMCS3 ROMCS4 ROMCS5 ROMCS6 TPAD14 ROMWE ROMOE SYSCLK SYSCLKA SWE OE SDRCS0 SDRCS1 SDRCS2 SDWE SDCKE SDRAS SDCAS SDCLK0 SDCLK1 SDCLK2 SDCLK0A SDCLK1A SDCLK2A SDCLK3A DQM[7:0] 5,15 5,15 5,16 5,16 5,16 16 16 16 16 6,15 16 16 7,15 7,15 7,15 7,15 7,15 7 7 6,15 6,15 15 16 16 16 5,15 5,15 5,15 5,15 5,15 SDDQM[7:0] 16 5,15 CE0 CE1 CE2 CE3 CE4 CE5 CE6 1 CE[6:0] R39-40 2 3 TC74LCX14FT IC3A ADDR16 ADDR11 ADDR10 ADDR8 ADDR7 ADDR5 ADDR4 ADDR3 ADDR18 ADDR9 ADDR6 ALE LACE R275 R264 R265 R276 R277 R266 R267 R268 R56 R57 R58 R42-44 R38 ADDR[2:0] R38 R39 R40 R42 R43 R44 ADDR[14:13] R*-* NO ASM NO ASM NO ASM 16 DATA[7] ADDR*/DATA* Setting Table DATA7 ADDR14 ADDR13 ADDR2 ADDR1 ADDR0 3 6,15 16 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K NOASM NOASM NOASM NOASM NOASM NOASM NOASM NOASM 4 BR26 3 2 1 33 ADDR18 ADDR16 ADDR17 ADDR19 2 4 BR23 3 2 1 33 5 6 7 8 5 6 7 8 1 BR21 8 2 7 3 6 4 5 33 4 BR18 5 3 6 2 7 1 8 33 4 BR16 5 3 6 2 7 1 8 33 ADDR13 ADDR12 ADDR15 ADDR14 ADDR11 ADDR10 ADDR8 ADDR9 ADDR4 ADDR7 ADDR5 ADDR6 ADDR3 ADDR0 ADDR1 ADDR2 ASM : Internal Timer Interrupt Disable NOASM : Internal Timer Interrupt Enable ASM/ASM : SYSCLK = G-BUSCLK/4 ASM/NOASM : SYSCLK = G-BUSCLK/3 NOASM/ASM : SYSCLK = G-BUSCLK/2 NOASM/NOASM : SYSCLK = G-BUSCLK NOASM/NOASM/NOASM : MASTERCLK : CPUCLK = 1 : 2 NOASM/NOASM/ASM : MASTERCLK : CPUCLK = 1 : 2.5 NOASM/ASM/NOASM : MASTERCLK : CPUCLK = 1 : 3 NOASM/ASM/ASM : MASTERCLK : CPUCLK = 1 : 4 ASM/NOASM/NOASM : MASTERCLK : CPUCLK = 1 : 8 ASM/NOASM/ASM : MASTERCLK : CPUCLK = 1 : 10 ASM/ASM/NOASM : MASTERCLK : CPUCLK = 1 : 12 ASM/ASM/ASM : MASTERCLK : CPUCLK = 1 : 16 FUNCTION 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 2 MEMA18 MEMA16 MEMA17 MEMA19 MEMA13 MEMA12 MEMA15 MEMA14 MEMA11 MEMA10 MEMA8 MEMA9 MEMA4 MEMA7 MEMA5 MEMA6 MEMA3 MEMA0 MEMA1 MEMA2 ASM/NOASM/NOASM NOASM/ASM ASM Default 1 1 MEMA[19:0] ADDR[19:0] 5,6,16 16 3/16 A B C D Sec07.fm 3 ページ ２００４年１２月７日 火曜日 午後４時５分 GA-1170 CIRCUIT DIAGRAM 7–4 A B C PPAR PTRDY PIRDY PFRAME 8 PLOCK 1 9,10,11 PPERR 9,10,11 PSERR 9,15 PCIGNT2 TPAD20 9 1 PCIGNT0 PCIGNT1 PCIREQ2 TPAD19 11,15 10,15 9,15 10,15 PCIREQ1 9,10,11 PSTOP 9,10,11 PDEVSEL 11,15 PCIREQ0 9,10,11 9,10,11 9,10,11 9,10,11 9,10,11 PCIBE[3:0] PCIBE0 PCIBE1 PCIBE2 PCIBE3 VCCIO 0.1uF 0.1uF 0.1uF 7 C38 C37 VCCINT C13 0.1uF 10K C12 VCCIO VCCIO 0.1uF C39 0.1uF C14 33 33 33 33 33 R242 R243 R244 R245 C41 0.1uF 0.1uF 0.1uF 0.1uF C40 C16 C15 0.1uF C42 0.1uF C17 0.1uF C43 0.1uF C18 0.1uF C44 0.1uF C19 0.1uF 0.1uF C46 0.1uF C45 C21 0.1uF 0.1uF C24 PCIAD0 PCIAD1 PCIAD2 PCIAD3 PCIAD4 PCIAD5 PCIAD6 PCIAD7 PCIAD8 PCIAD9 PCIAD10 PCIAD11 PCIAD12 PCIAD13 PCIAD14 PCIAD15 PCIAD16 PCIAD17 PCIAD18 PCIAD19 PCIAD20 PCIAD21 PCIAD22 PCIAD23 PCIAD24 PCIAD25 PCIAD26 PCIAD27 PCIAD28 PCIAD29 PCIAD30 PCIAD31 0.1uF C26 10uF C214 VCCINT 0.1uF PCICLK0 PCICLK1 PCICLK2 PCICLK3 PCICLK4 PCICLK5 PME EEPROM_DO EEPROM_CS EEPROM_SK C25 TMPR4927/4937 EEPROM_DI PCICLKIN LOCK M66EN PERR SERR GNT0 GNT1 GNT2 GNT3 REQ0 REQ1/INTOUT REQ2 REQ3 PAR FRAME IRDY TRDY STOP ID_SEL DEVSEL 0.1uF C48 16 TX4927/TX4937 3/5 C_BE0 C_BE1 C_BE2 C_BE3 IC1C 0.1uF C23 6pF NO ASM 0.1uF C47 A11 P26 C23 D20 B23 D22 J25 K24 L25 M25 K25 L22 L24 M24 C22 B25 A25 D24 B24 F24 C24 A20 B22 A26 F23 C11 0.1uF C22 TP407 C20 6 TP631 PCIBEA0 PCIBEA1 PCIBEA2 PCIBEA3 TP410 TP417 TP415 TP418 TP363 TP414 TP411 TP413 TP412 R86 33 33 33 33 33 33 33 33 R234 R235 R236 R237 R238 R239 R240 R241 33 33 33 33 33 8 7 6 5 R230 R231 R232 R233 1 2 3 4 BR32 TP362 TP361 TP390 TP393 TP406 TP364 TP365 TP416 TP408 TP409 PCIBEA0 PCIBEA1 PCIBEA2 PCIBEA3 PCIBEA[3:0] 10uF C215 0.1uF C27 H26 J26 K26 L26 M26 N26 N22 A12 A15 A14 B17 C17 A18 B18 D18 A19 B19 C19 B20 C20 E20 A21 B21 C21 E21 A22 C26 C25 D26 E26 E25 E24 E23 F26 G26 G25 G24 G23 G22 H24 J24 J22 5 0.1uF C28 TP661 PCIADA0 PCIADA1 PCIADA2 PCIADA3 PCIADA4 PCIADA5 PCIADA6 PCIADA7 PCIADA8 PCIADA9 PCIADA10 PCIADA11 PCIADA12 PCIADA13 PCIADA14 PCIADA15 PCIADA16 PCIADA17 PCIADA18 PCIADA19 PCIADA20 PCIADA21 PCIADA22 PCIADA23 PCIADA24 PCIADA25 PCIADA26 PCIADA27 PCIADA28 PCIADA29 PCIADA30 PCIADA31 5 0.1uF C29 R96 0.1uF C30 120 0.1uF C31 0.1uF C32 ICT31 10K VCCIO PME TP632 TP634 TP397 TP369 TP370 TP371 TP633 R87 0.1uF C33 1 R90 R91 R94 R95 56 56 56 56 0.1uF C34 TP3 10,11,16 1 4 0.1uF C35 0.1uF C36 PCICLK0 PCICLK1 PCICLK2 TPAD21 8 BR42 7 6 5 33 1 2 3 4 1 2 3 4 8 BR41 7 6 5 33 PCIADA26 PCIADA27 PCIADA24 PCIADA25 PCIADA30 PCIADA29 PCIADA31 PCIADA28 1 2 3 4 8 BR39 7 6 5 33 PCIADA23 PCIADA20 PCIADA22 PCIADA21 1 2 3 4 8 BR35 7 6 5 33 PCIADA15 PCIADA14 PCIADA13 PCIADA12 1 2 3 4 1 2 3 4 8 BR33 7 6 5 33 PCIADA11 PCIADA9 PCIADA10 PCIADA8 8 BR37 7 6 5 33 1 2 3 4 8 BR31 7 6 5 33 PCIADA7 PCIADA4 PCIADA5 PCIADA6 PCIADA19 PCIADA18 PCIADA16 PCIADA17 4 3 2 1 5 BR30 6 7 8 33 PCIADA1 PCIADA0 PCIADA3 PCIADA2 11,16 10,16 9 PCIAD30 PCIAD29 PCIAD31 PCIAD28 PCIAD26 PCIAD27 PCIAD24 PCIAD25 PCIAD23 PCIAD20 PCIAD22 PCIAD21 PCIAD19 PCIAD18 PCIAD16 PCIAD17 PCIAD15 PCIAD14 PCIAD13 PCIAD12 PCIAD11 PCIAD9 PCIAD10 PCIAD8 PCIAD7 PCIAD4 PCIAD5 PCIAD6 PCIAD1 PCIAD0 PCIAD3 PCIAD2 3 TX4927/TX4937 5/5 TMPR4927/4937 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS IC1E 9,10,11 PCIAD[31:0] K10 K11 K12 K13 K14 K15 K16 K17 L10 L11 L12 L13 L14 L15 L16 L17 M10 M11 M12 M13 M14 M15 M16 M17 N10 N11 N12 N13 N14 N15 N16 N17 16 PCIADA[31:0] 3 BLM41P600S 2 L1 1 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS 10uF P10 P11 P12 P13 P14 P15 P16 P17 R10 R11 R12 R13 R14 R15 R16 R17 T10 T11 T12 T13 T14 T15 T16 T17 U10 U11 U12 U13 U14 U15 U16 U17 10 R70 C5 10 R71 2 2 R24 P24 PVDD1 PVDD2 VCCIO VCCINT IC1D TX4927/TX4937 4/5 R25 P25 1 D4 D8 D10 D15 D17 D23 F5 G5 H23 K4 K23 M4 P22 R23 U4 U23 W4 AC4 AC10 AC12 AC17 AC19 AC23 A24 B5 C3 C9 C18 D12 D14 D16 D19 D21 D25 E4 E7 F22 F25 H4 H25 M3 M23 N5 N23 P5 R4 T4 T24 U24 V3 V4 V22 W23 Y22 AA3 AB7 AB23 AC5 AC8 AC9 AC13 AC14 AC15 AC16 AD1 AE2 AE21 AE24 AE26 AF9 AF11 AF20 AF23 TMPR4927/4937 VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIN VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO PLL1VDD_A PLL2VDD_A VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS PLL1VSS_A PLL2VSS_A A13 A23 B26 D2 D6 D9 E5 E8 E10 E12 E15 E17 E18 E19 E22 H5 H22 J23 K5 K22 L23 M5 M22 N4 N24 P2 P4 R5 R22 T1 T26 U5 U22 U26 V1 V2 V24 W3 W5 W22 W24 Y3 AA4 AA23 AB5 AB8 AB10 AB12 AB13 AB14 AB15 AB17 AB19 AB22 AB24 AB26 AC2 AC3 AC6 AC21 AC24 AD4 AD5 AD8 AD9 AD11 AD19 AD20 AD23 AE12 AE14 AE18 AE23 AF1 AF5 AF10 AF16 AF18 AF26 1 4/16 PVSS2 10 4 0.1uF R74 C4 BLM41P600S 2 L3 1 D 6 1000pF 10 TMPR4927TB_3 8.2K 8.2K 8.2K 8.2K 8.2K 8.2K 8.2K 8.2K R78 R79 R80 R81 R82 R83 R84 R85 BR29 1 2 3 4 8 7 6 5 7 1000pF R75 C6 10 R73 0.1uF 10 R72 C7 10 R76 L2 8 0 0 R88 R89 PVSS1 1 C8 10 R77 BLM41P600S 2 1 10uF C9 BLM41P600S 2 L4 A B C D Sec07.fm 4 ページ ２００４年１２月７日 火曜日 午後４時５分 GA-1170 CIRCUIT DIAGRAM 7–5 A B C D 8 MEMA[19:0] SDDQM[7:0] SDWE SDRCS0 SDRCS1 SDRCS2 SDRAS SDCAS SDCLK0 SDCLK1 SDCLK2 SDCKE DIMM_SDA DIMM_SCK 3,6,16 3,15 3,15 3,15 3,15 3,15 3,15 3,15 3,16 3,16 3,16 3,15 2,16 2,16 SDRAM 8 TP553 TP552 7 7 SDDQM3 SDDQM2 MEMA19 MEMA18 0.1uF C51 VCCIO MEMA5 MEMA6 MEMA7 MEMA8 MEMA9 MEMA10 MEMA11 MEMA12 MEMA13 MEMA14 MEMA15 MEMA16 MEMA17 SDDQM1 SDDQM0 MEMA19 MEMA18 0.1uF C49 VCCIO MEMA5 MEMA6 MEMA7 MEMA8 MEMA9 MEMA10 MEMA11 MEMA12 MEMA13 MEMA14 MEMA15 MEMA16 MEMA17 38 37 39 15 20 21 1 14 27 28 41 54 40 23 24 25 26 29 30 31 32 33 34 22 35 36 38 37 39 15 20 21 1 14 27 28 41 54 40 23 24 25 26 29 30 31 32 33 34 22 35 36 K4S561632D-TC75 CLK CKE UDQM LDQM BS0 BS1 VCC VCC VCC VSS VSS VSS NC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 IC6 K4S561632D-TC75 CLK CKE UDQM LDQM BS0 BS1 VCC VCC VCC VSS VSS VSS NC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 IC5 CS# WE# CAS# RAS# VCCQ VCCQ VCCQ VCCQ VSSQ VSSQ VSSQ VSSQ QD0 QD1 QD2 QD3 QD4 QD5 QD6 QD7 QD8 QD9 QD10 QD11 QD12 QD13 QD14 QD15 CS# WE# CAS# RAS# VCCQ VCCQ VCCQ VCCQ VSSQ VSSQ VSSQ VSSQ QD0 QD1 QD2 QD3 QD4 QD5 QD6 QD7 QD8 QD9 QD10 QD11 QD12 QD13 QD14 QD15 6 19 16 17 18 3 9 43 49 6 12 46 52 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 19 16 17 18 3 9 43 49 6 12 46 52 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 0.1uF C52 MEMD16 MEMD17 MEMD18 MEMD19 MEMD20 MEMD21 MEMD22 MEMD23 MEMD24 MEMD25 MEMD26 MEMD27 MEMD28 MEMD29 MEMD30 MEMD31 0.1uF C50 MEMD0 MEMD1 MEMD2 MEMD3 MEMD4 MEMD5 MEMD6 MEMD7 MEMD8 MEMD9 MEMD10 MEMD11 MEMD12 MEMD13 MEMD14 MEMD15 6 VCCIO VCCIO 5 5 4 4 VCCIO SDDQM0 SDDQM1 SDDQM2 SDDQM3 SDDQM4 SDDQM5 SDDQM6 SDDQM7 MEMA19 MEMA18 MEMA5 MEMA6 MEMA7 MEMA8 MEMA9 MEMA10 MEMA11 MEMA12 MEMA13 MEMA14 MEMA15 MEMA16 MEMA17 11 12 27 28 45 46 63 64 81 82 101 102 113 114 129 130 143 144 57 58 59 60 77 78 79 80 73 141 142 23 25 115 117 24 26 116 118 62 68 61 74 65 66 67 69 71 106 110 29 31 33 30 32 34 103 104 105 109 111 112 70 72 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 DM-3B1-N1210 VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD NC NC NC NC NC NC NC NC DU SDA SCL DQM0 DQM1 DQM2 DQM3 DQM4 DQM5 DQM6 DQM7 CKE0 CKE1 CLK0 CLK1 RAS CAS WE CS0 CS1 BA0 BA1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 A13 CN2 3 1 2 21 22 35 36 55 56 75 76 91 92 107 108 119 120 139 140 3 5 7 9 13 15 17 19 37 39 41 43 47 49 51 53 83 85 87 89 93 95 97 99 121 123 125 127 131 133 135 137 4 6 8 10 14 16 18 20 38 40 42 44 48 50 52 54 84 86 88 90 94 96 98 100 122 124 126 128 132 134 136 138 MEMD0 MEMD1 MEMD2 MEMD3 MEMD4 MEMD5 MEMD6 MEMD7 MEMD8 MEMD9 MEMD10 MEMD11 MEMD12 MEMD13 MEMD14 MEMD15 MEMD16 MEMD17 MEMD18 MEMD19 MEMD20 MEMD21 MEMD22 MEMD23 MEMD24 MEMD25 MEMD26 MEMD27 MEMD28 MEMD29 MEMD30 MEMD31 MEMD32 MEMD33 MEMD34 MEMD35 MEMD36 MEMD37 MEMD38 MEMD39 MEMD40 MEMD41 MEMD42 MEMD43 MEMD44 MEMD45 MEMD46 MEMD47 MEMD48 MEMD49 MEMD50 MEMD51 MEMD52 MEMD53 MEMD54 MEMD55 MEMD56 MEMD57 MEMD58 MEMD59 MEMD60 MEMD61 MEMD62 MEMD63 3 10uF C208 0.1uF 0.1uF VCCIO C54 C53 VCCIO 10uF C209 0.1uF C55 MEMD[63:0] 0.1uF 0.1uF 2 10uF C210 C57 C56 3,6,16 2 0.1uF C58 0.1uF C59 0.1uF C60 0.1uF C61 1 0.1uF C62 1 5/16 A B C D Sec07.fm 5 ページ ２００４年１２月７日 火曜日 午後４時５分 GA-1170 CIRCUIT DIAGRAM 7–6 A B C D 7 8 3,15 MEMDIR 3,5,16 MEMD[31:0] 3,5,16 MEMA[19:0] C68 0.1uF 0.1uF MEMD23 MEMD22 MEMD21 MEMD20 MEMD19 MEMD18 MEMD17 MEMD16 MEMD31 MEMD30 MEMD29 MEMD28 MEMD27 MEMD26 MEMD25 MEMD24 0.1uF C65 C67 VCCIO 0.1uF C64 VCCIO MEMA8 MEMA9 MEMA10 MEMA11 MEMA12 MEMA13 MEMA14 MEMA15 MEMA0 MEMA1 MEMA2 MEMA3 MEMA4 MEMA5 MEMA6 MEMA7 7 1 19 2 4 6 8 11 13 15 17 1 19 2 4 6 8 11 13 15 17 19 1 2 3 4 5 6 7 8 9 GND VCC B1 B2 B3 B4 B5 B6 B7 B8 RXD1 GND VCC B1 B2 B3 B4 B5 B6 B7 B8 TC74LCX245FT OE DIR A1 A2 A3 A4 A5 A6 A7 A8 IC13 TC74LCX245FT OE DIR A1 A2 A3 A4 A5 A6 A7 A8 IC11 2,16 2,16 10 20 18 16 14 12 9 7 5 3 10 20 18 16 14 12 9 7 5 3 TXD1 GND VCC 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 TC74LCX244FT 1G 2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 IC9 19 1 2 3 4 5 6 7 8 9 GND VCC 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 TC74LCX244FT 1G 2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 IC7 10 20 18 17 16 15 14 13 12 11 10 20 18 17 16 15 14 13 12 11 ADDRESS_BUFFER/DATA_BUFFER 8 LDD23 LDD22 LDD21 LDD20 LDD19 LDD18 LDD17 LDD16 LDD31 LDD30 LDD29 LDD28 LDD27 LDD26 LDD25 LDD24 R202 LAA8 LAA9 LAA10 LAA11 LAA12 LAA13 LAA14 LAA15 LAA0 LAA1 LAA2 LAA3 LAA4 LAA5 LAA6 LAA7 VCCIO VCCIO 1 2 6 0.1uF C70 MEMD7 MEMD6 MEMD5 MEMD4 MEMD3 MEMD2 MEMD1 MEMD0 MEMD15 MEMD14 MEMD13 MEMD12 MEMD11 MEMD10 MEMD9 MEMD8 TC74LCX14FT 5 3 MEMA16 MEMA17 MEMA18 MEMA19 IC29C TP470 0.1uF C69 VCCIO TP466 6 33 TC74LCX14FT IC29A 3,15 ROMWE 3,15 ROMOE 6 4 TP471 19 1 2 3 4 5 6 7 8 9 19 1 2 3 4 5 6 7 8 9 GND VCC 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 GND VCC B1 B2 B3 B4 B5 B6 B7 B8 10 20 18 17 16 15 14 13 12 11 5 GND VCC B1 B2 B3 B4 B5 B6 B7 B8 10 20 18 17 16 15 14 13 12 11 LDD7 LDD6 LDD5 LDD4 LDD3 LDD2 LDD1 LDD0 LDD15 LDD14 LDD13 LDD12 LDD11 LDD10 LDD9 LDD8 VCCIO VCC R246 10K 33 FOE FONT_OE FWE FONT_WE VCC 1 2 3 4 T4B-SQ TXD RXD 5V GND CN6 LAA16 LAA17 LAA18 LAA19 R97 R98 R99 R100 33 33 33 33 LAA[19:0] TP400 TP401 TP446 TP447 VCCIO LDD[31:0] TC74LCX245FT OE DIR A1 A2 A3 A4 A5 A6 A7 A8 IC14 9 10 20 18 16 14 12 9 7 5 3 TC74LCX14FT IC29D R201 0.1uF C63 TC74LCX245FT DIR A1 A2 A3 A4 A5 A6 A7 A8 IC12 8 TP465 VCCIO TC74LCX244FT 1G 2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 IC8 TC74LCX14FT IC29B 1 19 2 4 6 8 11 13 15 17 5 3,15 7,15 7,15 7,15 7,15 4 4 ALE LAA12 8 7 6 5 8 7 6 5 1 BR58 2 3 4 33 1 BR60 2 3 4 33 LDD15 LDD14 LDD13 LDD12 LDD11 LDD10 LDD9 LDD8 8 7 6 5 8 7 6 5 1 BR62 2 3 4 33 1 BR64 2 3 4 33 LDD7 LDD6 LDD5 LDD4 LDD3 LDD2 LDD1 LDD0 8 7 6 5 1 BR56 2 3 4 33 LDD19 LDD18 LDD17 LDD16 8 7 6 5 8 7 6 5 8 7 6 5 1 BR54 2 3 4 33 1 BR52 2 3 4 33 1 BR50 2 3 4 33 LDD23 LDD22 LDD21 LDD20 LDD27 LDD26 LDD25 LDD24 LDD31 LDD30 LDD29 LDD28 16 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 LD3 LD2 LD1 LD0 LD7 LD6 LD5 LD4 LD11 LD10 LD9 LD8 LD15 LD14 LD13 LD12 LD19 LD18 LD17 LD16 LD23 LD22 LD21 LD20 LD27 LD26 LD25 LD24 LD31 LD30 LD29 LD28 GND 10 20 2 5 6 9 12 15 16 19 8 7 6 5 8 7 6 5 8 7 6 5 1 2 3 4 1 2 3 4 LAB20 33 3 33 33 BR47 33 BR46 33 BR45 33 BR44 BR43 R210 VCC TC74LCX373FT LE OE D0 D1 D2 D3 D4 D5 D6 D7 IC10 LDD[31:0] 11 1 3 4 7 8 13 14 17 18 LAB20 1 2 3 4 LAA15 LAA14 LAA13 LAA12 LAA16 LAA17 LAA18 LAA19 1 2 3 4 LAA8 LAA9 LAA10 LAA11 8 7 6 5 8 7 6 5 1 2 3 4 LAA4 LAA5 LAA6 LAA7 LAA0 LAA1 LAA2 LAA3 3 VCCIO TP556 0.1uF C66 TP555 LA20 LA16 LA17 LA18 LA19 LA15 LA14 LA13 LA12 LA8 LA9 LA10 LA11 LA4 LA5 LA6 LA7 LA0 LA1 LA2 LA3 TP557 8 7 6 5 8 7 6 5 1 BR63 2 3 4 10K 1 BR65 2 3 4 10K LD3 LD2 LD1 LD0 8 7 6 5 LD7 LD6 LD5 LD4 1 BR61 2 3 4 10K 8 7 6 5 1 BR59 2 3 4 10K LD15 LD14 LD13 LD12 8 7 6 5 8 7 6 5 8 7 6 5 8 7 6 5 LD11 LD10 LD9 LD8 16 VCCIO LD[31:0] TP561 1 BR57 2 3 4 10K 1 BR55 2 3 4 10K 1 BR53 2 3 4 10K 1 BR51 2 3 4 10K TP560 LD19 LD18 LD17 LD16 LD23 LD22 LD21 LD20 LD27 LD26 LD25 LD24 2 TP559 LD31 LD30 LD29 LD28 TP558 7 LA[20:0] LAB20 16 2 LAA[19:0] 7 1 1 6/16 A B C D Sec07.fm 6 ページ ２００４年１２月７日 火曜日 午後４時５分 CIRCUIT DIAGRAM A B C D 8 VCCWCTL FWE PONRST 6,15 2,9,10,11,13,15 2,16 ROMCS2 FOE ROMCS1 LA[20:0] 3,15 6,15 3,15 6 3,15 33 R219 ROMCS0 10k R109 VCCIO VCCIO 10K 7 0.1uF C222 3 4 5 TC7SB66FU NOASM 2 IC34 LA20 LA0 LA1 LA2 LA3 LA4 LA5 LA6 LA7 LA8 LA9 LA10 LA11 LA12 LA13 LA14 LA15 LA16 LA17 LA18 LA19 1 20 39 44 46 47 40 42 11 30 41 43 72 12 13 14 15 16 17 18 28 31 32 29 33 34 36 65 66 67 68 69 70 71 10k R220 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30 D31 0.1uF C220 6 VCC VCC VCCW RP RY/BY BYTE DMM2-SD72A-1131 GND GND GND OE WP WE 1CE 2CE NC NC NC NC NC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 CN3 10 61 55 19 45 48 2 3 4 5 6 7 8 9 21 22 23 24 25 26 27 35 37 38 49 50 51 52 53 54 56 57 58 60 59 62 63 64 0.47uF C221 LD24 LD25 LD26 LD27 LD28 LD29 LD30 LD31 LD16 LD17 LD18 LD19 LD20 LD21 LD22 LD23 LD8 LD9 LD10 LD11 LD12 LD13 LD14 LD15 LD0 LD1 LD2 LD3 LD4 LD5 LD6 LD7 1 FWP NOASM 0 R282 0 R281 R106 0.47uF C235 0.1uF C73 VCCIO 0.1uF C71 TP690 10uF C79 TP705 0 NOASM R280 0 R279 R107 NOASM VCCIO 10K R105 FLASH 5 5 0 LA20 LA20 LA0 LA1 LA2 LA3 LA4 LA5 LA6 LA7 LA8 LA9 LA10 LA11 LA12 LA13 LA14 LA15 LA16 LA17 LA18 LA19 VCCWA 1 20 39 44 46 47 40 42 11 30 41 43 72 12 13 14 15 16 17 18 28 31 32 29 33 34 36 65 66 67 68 69 70 71 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30 D31 4 VCC VCC VCCW RP RY/BY BYTE DMM2-SD72A-1131 GND GND GND OE WP WE 1CE 2CE NC NC NC NC NC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 CN4 10 61 55 19 45 48 2 3 4 5 6 7 8 9 21 22 23 24 25 26 27 35 37 38 49 50 51 52 53 54 56 57 58 60 59 62 63 64 LD24 LD25 LD26 LD27 LD28 LD29 LD30 LD31 LD16 LD17 LD18 LD19 LD20 LD21 LD22 LD23 LD8 LD9 LD10 LD11 LD12 LD13 LD14 LD15 LD0 LD1 LD2 LD3 LD4 LD5 LD6 LD7 0.1uF C74 VCCIO 4 0.1uF C72 3,15 3,15 3 3 3 ROMCS3 ROMCS4 ROMCS5 ROMCS6 3 6,15 6,15 FONT_WE FONT_OE VCCIO LA0 LA1 LA2 LA3 LA4 LA5 LA6 LA7 LA8 LA9 LA10 LA11 LA12 LA13 LA14 LA15 LA16 LA17 LA18 LA19 LA20 26 44 94 74 75 76 77 97 3 27 47 53 25 24 72 73 23 22 18 68 19 69 20 70 21 71 7 57 8 58 9 59 10 60 11 61 12 62 13 63 14 64 15 65 16 66 17 67 GND GND GND GND GND GND GND GND GND GND Vcc Vcc Vcc Vcc Vcc Vcc Vcc Vcc Vpp Vpp D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30 D31 2 DMM-100G-432FNK31 NC NC NC CE0_ CE1_ CE2_ CE3_ NC NC NC NC NC RY/BY_ WP_ RP BYTE_ WE_ OE_ NC NC Vpp Vpp Vpp Vpp NC NC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 CN5 1 2 48 49 50 51 52 98 99 100 5 6 45 46 55 56 95 96 4 54 28 78 29 79 30 80 31 81 32 82 33 83 34 84 35 85 36 86 37 87 38 88 39 89 40 90 41 91 42 92 43 93 LD24 LD25 LD26 LD27 LD28 LD29 LD30 LD31 LD16 LD17 LD18 LD19 LD20 LD21 LD22 LD23 LD8 LD9 LD10 LD11 LD12 LD13 LD14 LD15 LD0 LD1 LD2 LD3 LD4 LD5 LD6 LD7 2 + 1 6 7/16 LD[31:0] 1 VCCIO 0.1uF C76 6 0.1uF C77 7 0.1uF 8 22uF/16V 7–7 C78 GA-1170 C75 A B C D Sec07.fm 7 ページ ２００４年１２月７日 火曜日 午後４時５分 A B C D 8 2,16 2,16 2,16 2,16 Serial_EEPROM/RTC RTCCS 7 RTCCLK RTCR/W RTCDATA IC25F 12 TC74LCX14FT 13 TP551 VCCIO 6 6 IC32A 2 1 6 1 3 1 74LCX125MTC 1 IC32B 4 EN 5 74LCX125MTC 1 IC32D 13 EN 12 74LCX125MTC 10 EN 9 IC32C 6 11 8 MM74HC125MTC 1 EN 2 IC35A MM74HC125MTC 1 IC35B 4 EN 5 MM74HC125MTC 1 11 74LCX125MTC IC35D 13 EN 12 3 8 MM74HC125MTC 1 IC35C 10 EN 9 TP666 TP563 TP562 TP664 TP663 TP665 EEP_SCK 2,16 TP550 EEP_SDA 2,16 VCC 5 1K VCC VCCIO C244 10pF 10pF 1K 8 7 6 5 C243 0.1uF C224 4 GND A0 A1 A2 3 2 7 1 6 5 0.1uF 4 1 2 3 4 NJU6356EM XT- XT DATA I/OCLK CE IC18 VSS VDD
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Modify Date : 2005:02:07 12:20:28+09:00 Create Date : 2001:07:03 17:56:59Z Page Count : 37 Has XFA : No Page Layout : SinglePage Page Mode : UseOutlines Producer : Acrobat Distiller 4.05 for Windows Author : Mod Date : 2005:02:07 12:20:28+09:00 Creation Date : 2001:07:03 17:56:59Z Metadata Date : 2005:02:07 12:20:28+09:00 Creator : Title : GA-1170 Service ManualEXIF Metadata provided by EXIF.tools